ALCATEL-IND1-ETHERNET-OAM-MIB

File: ALCATEL-IND1-ETHERNET-OAM-MIB.mib (14320 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
ALCATEL-IND1-BASE IEEE8021-CFM-MIB

Imported symbols

OBJECT-TYPE MODULE-IDENTITY OBJECT-IDENTITY
Integer32 Unsigned32 MacAddress
OBJECT-GROUP MODULE-COMPLIANCE softentIND1EthernetOam
Dot1agCfmMepId dot1agCfmMaIndex Dot1agCfmMepIdOrZero
dot1agCfmMdIndex dot1agCfmMepIdentifier dot1agCfmMepEntry

Defined Objects

alcatelIND1EoamMIB 1.3.6.1.4.1.6486.800.1.2.1.40.1
This module describes an authoritative enterprise- specific Simple Network Management Protocol (SNMP) Management Information Base (MIB): For the Birds Of Prey Product Line Ethernet OAM for the Connectivity Fault Management. The right to make changes in specification and other information contained in this document without prior notice is reserved. No liability shall be assumed for any incidental, indirect, special, or consequential damages whatsoever arising from or related to this document or the information contained herein. Vendors, end-users, and other interested parties are granted non-exclusive license to use this specification in connection with management of the products for which it is intended to be used. Copyright (C) 1995-2002 Alcatel Internetworking, Incorporated ALL RIGHTS RESERVED WORLDWIDE
MODULE-IDENTITY    

alcatelIND1CfmMIBObjects 1.3.6.1.4.1.6486.800.1.2.1.40.1.1
Branch For Connectivity Fault Management (Ethernet OAM) Objects.
OBJECT-IDENTITY    

alaCfmBase 1.3.6.1.4.1.6486.800.1.2.1.40.1.1.1
OBJECT IDENTIFIER    

alaCfmGlobalClearStats 1.3.6.1.4.1.6486.800.1.2.1.40.1.1.1.1
Defines the global clear statistics control for Ethernet OAM. The value reset (1) indicates that Ethernet OAM should clear all statistic counters related to all MEPs in the system. By default, this object contains a zero value.
OBJECT-TYPE    
  INTEGER default(0), reset(1)  

alaCfmGlobalOWDClear 1.3.6.1.4.1.6486.800.1.2.1.40.1.1.1.2
Defines the global clear of one-way-delay entries control for Ethernet OAM. The value reset (1) indicates that Ethernet OAM should remove all the one-way-delay entries in the delay result table. By default, this object contains a zero value.
OBJECT-TYPE    
  INTEGER default(0), reset(1)  

alaCfmGlobalTWDClear 1.3.6.1.4.1.6486.800.1.2.1.40.1.1.1.3
Defines the global clear of two-way-delay entries control for Ethernet OAM. The value reset (1) indicates that Ethernet OAM should remove all the two-way-delay entries in the delay result table. By default, this object contains a zero value.
OBJECT-TYPE    
  INTEGER default(0), reset(1)  

alaCfmMep 1.3.6.1.4.1.6486.800.1.2.1.40.1.1.2
OBJECT IDENTIFIER    

alaCfmMepTable 1.3.6.1.4.1.6486.800.1.2.1.40.1.1.2.1
This table augments the MEP table for clearing statistics based on MdIndex/MaIndex/MEPId. This table also contains the objects for initiating 1DM and DMM.
OBJECT-TYPE    
  SEQUENCE OF  
    AlaCfmMepEntry

alaCfmMepEntry 1.3.6.1.4.1.6486.800.1.2.1.40.1.1.2.1.1
Each row entry in the alaCfmMepTable represents additional column for proprietary extension to the existing MEP table. It provides the facility to clear the statistics based on uniquely identified MEP. It also provides the facility to intiate 1DM and DMM
OBJECT-TYPE    
  AlaCfmMepEntry  

alaCfmMepClearStats 1.3.6.1.4.1.6486.800.1.2.1.40.1.1.2.1.1.1
Reset all statistics parameters corresponding to this MEP. By default, this objects contains a zero value.
OBJECT-TYPE    
  INTEGER default(0), reset(1)  

alaCfmMepOWDTMacAddress 1.3.6.1.4.1.6486.800.1.2.1.40.1.1.2.1.1.2
Specifies the MAC address used as a target for the One-Way-Delay Test (OWDT). Setting this object will trigger a One-Way-Delay test to the specified MAC address. The number of messages transmitted per initiation will be 2. Upon completion of the test, the MacAddress will revert to it's default value, indicating that another test is possible.
OBJECT-TYPE    
  MacAddress  

alaCfmMepOWDTRMepIdentifier 1.3.6.1.4.1.6486.800.1.2.1.40.1.1.2.1.1.3
Specifies the Mep-Id assigned to the Remote MEP.
OBJECT-TYPE    
  Dot1agCfmMepId  

alaCfmMepOWDTPriority 1.3.6.1.4.1.6486.800.1.2.1.40.1.1.2.1.1.4
Specifies the priority used in the generated test frame for the One-Way-Delay test.
OBJECT-TYPE    
  Unsigned32 0..7  

alaCfmMepTWDTMacAddress 1.3.6.1.4.1.6486.800.1.2.1.40.1.1.2.1.1.5
Specifies the MAC address used as a target for the Two-Way-Delay Test (TWDT). Setting this object will trigger a Two-Way-Delay test to the specified MAC address. The number of messages transmitted per initiation will be 2. Upon completion of the test, the MacAddress will revert to it's default value, indicating that another test is possible.
OBJECT-TYPE    
  MacAddress  

alaCfmMepTWDTRMepIdentifier 1.3.6.1.4.1.6486.800.1.2.1.40.1.1.2.1.1.6
Specifies the Mep-Id assigned to the Remote MEP.
OBJECT-TYPE    
  Dot1agCfmMepId  

alaCfmMepTWDTPriority 1.3.6.1.4.1.6486.800.1.2.1.40.1.1.2.1.1.7
Specifies the priority used in the generated test frame for the Two-Way-Delay test.
OBJECT-TYPE    
  Unsigned32 0..7  

alaCfmDelayResult 1.3.6.1.4.1.6486.800.1.2.1.40.1.1.3
OBJECT IDENTIFIER    

alaCfmDelayResultTable 1.3.6.1.4.1.6486.800.1.2.1.40.1.1.3.1
Indicates the results of all the One-Way/Two-Way Delay Tests from the originating MAC addresses. This table is not persistent over reboots of the chassis.
OBJECT-TYPE    
  SEQUENCE OF  
    AlaCfmDelayResultEntry

alaCfmDelayResultEntry 1.3.6.1.4.1.6486.800.1.2.1.40.1.1.3.1.1
The MEP delay result table.
OBJECT-TYPE    
  AlaCfmDelayResultEntry  

alaCfmDelayResultType 1.3.6.1.4.1.6486.800.1.2.1.40.1.1.3.1.1.1
Indicates the type of test this row details.
OBJECT-TYPE    
  INTEGER oneWayTest(1), twoWayTest(2)  

alaCfmDelayResultRMepMacAddress 1.3.6.1.4.1.6486.800.1.2.1.40.1.1.3.1.1.2
Indicates the MAC address of the Remote MEP.
OBJECT-TYPE    
  MacAddress  

alaCfmDelayResultRMepIdentifier 1.3.6.1.4.1.6486.800.1.2.1.40.1.1.3.1.1.3
Indicates the Mep-Id of the Remote MEP. Valid only in the case of two-way delay. When initiated for a target Mep-Id contains the Mep-Id of the target, else if two-way delay initiated for a target mac-address contains '0'.
OBJECT-TYPE    
  Dot1agCfmMepIdOrZero  

alaCfmDelayResultTestDelay 1.3.6.1.4.1.6486.800.1.2.1.40.1.1.3.1.1.4
Indicates the amount of time, measured in microseconds, from when the test-frame was transmitted to the time it was received minus the local processing time taken by the remote system.
OBJECT-TYPE    
  Integer32  

alaCfmDelayResultVariation 1.3.6.1.4.1.6486.800.1.2.1.40.1.1.3.1.1.5
Indicates the amount of time delay variation, measured in microseconds, from the two most recent time delay measurements
OBJECT-TYPE    
  Unsigned32  

alaCfmConformance 1.3.6.1.4.1.6486.800.1.2.1.40.1.2
OBJECT IDENTIFIER    

alaCfmGroups 1.3.6.1.4.1.6486.800.1.2.1.40.1.2.1
OBJECT IDENTIFIER    

alaCfmBaseGroup 1.3.6.1.4.1.6486.800.1.2.1.40.1.2.1.1
Mandatory objects for the Base group
OBJECT-GROUP    

alaCfmMepGroup 1.3.6.1.4.1.6486.800.1.2.1.40.1.2.1.2
Mandatory objects for the MEP group. Proprietary extension to support statistics clearing and one-way and two-way delay tests.
OBJECT-GROUP    

alaCfmDelayResultGroup 1.3.6.1.4.1.6486.800.1.2.1.40.1.2.1.3
Mandatory objects for the Delay Result Group.
OBJECT-GROUP    

alaCfmCompliances 1.3.6.1.4.1.6486.800.1.2.1.40.1.2.2
OBJECT IDENTIFIER    

alaCfmCompliance 1.3.6.1.4.1.6486.800.1.2.1.40.1.2.2.1
The compliance statement for support of CFM.
MODULE-COMPLIANCE    

Defined Objects

AlaCfmMepEntry  
SEQUENCE    
  INTEGER as alaCfmMepClearStats  
  MacAddress as alaCfmMepOWDTMacAddress  
  Dot1agCfmMepId as alaCfmMepOWDTRMepIdentifier  
  Unsigned32 as alaCfmMepOWDTPriority  
  MacAddress as alaCfmMepTWDTMacAddress  
  Dot1agCfmMepId as alaCfmMepTWDTRMepIdentifier  
  Unsigned32 as alaCfmMepTWDTPriority  

AlaCfmDelayResultEntry  
SEQUENCE    
  INTEGER as alaCfmDelayResultType  
  MacAddress as alaCfmDelayResultRMepMacAddress  
  Dot1agCfmMepIdOrZero as alaCfmDelayResultRMepIdentifier  
  Integer32 as alaCfmDelayResultTestDelay  
  Unsigned32 as alaCfmDelayResultVariation