ALCATEL-IND1-PIM-MIB

File: ALCATEL-IND1-PIM-MIB.mib (26226 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
ALCATEL-IND1-BASE

Imported symbols

MODULE-IDENTITY OBJECT-TYPE IpAddress
Integer32 TimeTicks RowStatus
MODULE-COMPLIANCE OBJECT-GROUP routingIND1Pim

Defined Objects

alcatelIND1PIMMIB 1.3.6.1.4.1.6486.800.1.2.1.10.6.1
This module describes an authoritative enterprise-specific Simple Network Management Protocol (SNMP) Management Information Base (MIB): This proprietary MIB contains management information for the configuration of PIM-SM and PIM-DM global configuration parameters. The right to make changes in specification and other information contained in this document without prior notice is reserved. No liability shall be assumed for any incidental, indirect, special, or consequential damages whatsoever arising from or related to this document or the information contained herein. Vendors, end-users, and other interested parties are granted non-exclusive license to use this specification in connection with management of the products for which it is intended to be used. Copyright (C) 1995-2007 Alcatel-Lucent ALL RIGHTS RESERVED WORLDWIDE
MODULE-IDENTITY    

alcatelIND1PIMMIBObjects 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1
OBJECT IDENTIFIER    

alaPimsmGlobalConfig 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.1
OBJECT IDENTIFIER    

alaPimsmAdminStatus 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.1.1
Administratively enables/disables the PIM-SM protocol on this router.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaPimsmAdminBSRAddress 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.1.2
The IP address used to source the bootstrap message when the router is configured to be a candidate bootstrap router (C-BSR). This IP address should belong to a PIM-enabled VLAN.
OBJECT-TYPE    
  IpAddress  

alaPimsmAdminBSRHashmasklen 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.1.3
The length (in bits) of the mask to use in the hash function when computing the rendezvous point (RP) for a multicast group. This value may be changed to facilitate vendor inter-operability. For IPV4 we recommend a value of 30.
OBJECT-TYPE    
  Integer32 1..32  

alaPimsmAdminBSRPriority 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.1.4
The candidate bootstrap router's (C-BSR) priority. The C-BSR with the biggest priority value will be elected as the BSR for this domain.
OBJECT-TYPE    
  Integer32 0..255  

alaPimsmCRPExpiryTime 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.1.5
The maximum time a PIM-SM router considers the current candidate rendezvous point (C-RP) active.
OBJECT-TYPE    
  Integer32 1..300  

alaPimsmCRPInterval 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.1.6
This is the interval at which the candidate rendezvous point router's advertisements (C-RP-Adv) are sent to the bootstrap router.
OBJECT-TYPE    
  Integer32 1..300  

alaPimsmAdminCRPAddress 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.1.7
The IP Address of the C-RP when this router is configured to be a Candidate RP. This IP address should belong to a PIM-enabled vlan. The value of 0 indicates that this router is not configured to be a C-RP.
OBJECT-TYPE    
  IpAddress  

alaPimsmAdminCRPPriority 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.1.8
The candidate rendezvous point (C-RP) router's priority. A lower numeric value denotes a higher priority.
OBJECT-TYPE    
  Integer32 0..128  

alaPimsmDataTimeout 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.1.9
This is the time after which (S,G) state for a silent source will be deleted.
OBJECT-TYPE    
  Integer32 1..300  

alaPimsmMaxRPs 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.1.10
The maximum number of C-RPs allowed in the PIM-SM domain.
OBJECT-TYPE    
  Integer32 1..100  

alaPimsmProbeTime 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.1.11
When NULL Registers are used, this is the time between sending a NULL Register and the Register- Suppression-Timer expiring unless it is restarted by receiving a Register-Stop.
OBJECT-TYPE    
  Integer32 1..300  

alaPimsmOldRegisterMessageSupport 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.1.12
Specifies the application of the checksum function on received Register messages in the PIM-SM domain. When set to full(2), the checksum for a register message is computed for the entire packet (i.e. includes data). When set to header(1), the checksum is done only on the first 8 bytes of the packet. This variable is provided for interoperability reasons and may be required for Compatibility with older implementations of PIM-SM v2. This parameter must be set the same throughout the PIM-SM domain.
OBJECT-TYPE    
  INTEGER header(1), full(2)  

alaPimsmRegisterSuppressionTimeout 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.1.13
This is the amount of time a Designated Router (DR) will stop sending Registers on behalf of sources to the RP once a Register-Stop has been received.
OBJECT-TYPE    
  Integer32 1..300  

alaPimsmAdminStaticRPConfig 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.1.14
Administratively enables/disables Static RP Configuration on this router.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaPimsmStaticRPTable 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.1.15
The (conceptual) table listing the IP multicast groups to be used in the group-to-RP mapping when the value of alaPimsmAdminStaticRPConfig is enabled.
OBJECT-TYPE    
  SEQUENCE OF  
    AlaPimsmStaticRPEntry

alaPimsmStaticRPEntry 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.1.15.1
An entry (conceptual row) in the alaPimsmStaticRPTable.
OBJECT-TYPE    
  AlaPimsmStaticRPEntry  

alaPimsmStaticRPGroupAddress 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.1.15.1.1
The IP multicast group address which, when combined with alaPimsmStaticRPGroupMask, identifies a group prefix to be used in the group-to-rp mapping algorithm.
OBJECT-TYPE    
  IpAddress  

alaPimsmStaticRPGroupMask 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.1.15.1.2
The multicast group address mask which, when combined with alaPimsmStaticRPGroupMask, identifies a group prefix to be used in the group-to-rp mapping algorithm.
OBJECT-TYPE    
  IpAddress  

alaPimsmStaticRPAddress 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.1.15.1.3
The (unicast) address of the interface which will be an RP.
OBJECT-TYPE    
  IpAddress  

alaPimsmStaticRPRowStatus 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.1.15.1.4
The status of this row, by which new entries may be created, or old entries deleted from this table.
OBJECT-TYPE    
  RowStatus  

alaPimsmAdminSPTConfig 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.1.16
Administratively enables/disables SPT Switchover upon receiving the first data packet.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaPimsmRPThreshold 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.1.17
Sets the RP threshold value (in bps) to be used in determining when to switch to native forwarding at the RP. The value of 0 disables the RP Threshold functionality.
OBJECT-TYPE    
  Integer32 0..2147483647  

alaPimsmV6AdminStatus 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.1.18
Administratively enables/disables the PIM-SM IPv6 protocol on this router.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaPimsmV6SPTConfig 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.1.19
Administratively enables/disables PIM IPv6 SPT Switchover upon receiving the first data packet.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaPimsmV6RPSwitchover 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.1.20
Administratively enables/disables whether PIM IPv6 will attempt to switch to native forwarding at the RP upon receiving the first register-encapsulated packet.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaPimsmDebugConfig 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.2
OBJECT IDENTIFIER    

alaPimsmDebugLevel 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.2.1
This Object is deprecated in favor of alaDrcTmPimsmDebug Configuration
OBJECT-TYPE    
  Integer32 0..255  

alaPimsmDebugError 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.2.2
This Object is deprecated in favor of alaDrcTmPimsmDebugError MIB Object of alaDrcTmPimsmDebug Configuration
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaPimsmDebugHello 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.2.3
This Object is deprecated in favor of alaDrcTmPimsmDebugHello MIB Object of alaDrcTmPimsmDebug Configuration
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaPimsmDebugNbr 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.2.4
This Object is deprecated in favor of alaDrcTmPimsmDebugNbr MIB Object of alaDrcTmPimsmDebug Configuration
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaPimsmDebugBootstrap 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.2.5
This Object is deprecated in favor of alaDrcTmPimsmDebugBootstrap MIB Object of alaDrcTmPimsmDebug Configuration
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaPimsmDebugCRP 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.2.6
This Object is deprecated in favor of alaDrcTmPimsmDebugCRP MIB Object of alaDrcTmPimsmDebug Configuration
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaPimsmDebugRoute 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.2.7
This Object is deprecated in favor of alaDrcTmPimsmDebugRoute MIB Object of alaDrcTmPimsmDebug Configuration
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaPimsmDebugJoinPrune 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.2.8
This Object is deprecated in favor of alaDrcTmPimsmDebugJoinPrune MIB Object of alaDrcTmPimsmDebug Configuration
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaPimsmDebugAssert 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.2.9
This Object is deprecated in favor of alaDrcTmPimsmDebugAssert MIB Object of alaDrcTmPimsmDebug Configuration
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaPimsmDebugTime 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.2.10
This Object is deprecated in favor of alaDrcTmPimsmDebugTime MIB Object of alaDrcTmPimsmDebug Configuration
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaPimsmDebugIgmp 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.2.11
This Object is deprecated in favor of alaDrcTmPimsmDebugIgmp MIB Object of alaDrcTmPimsmDebug Configuration
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaPimsmDebugSpt 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.2.12
This Object is deprecated in favor of alaDrcTmPimsmDebugSpt MIB Object of alaDrcTmPimsmDebug Configuration
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaPimsmDebugMip 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.2.13
This Object is deprecated in favor of alaDrcTmPimsmDebugMip MIB Object of alaDrcTmPimsmDebug Configuration
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaPimsmDebugInit 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.2.14
This Object is deprecated in favor of alaDrcTmPimsmDebugInit MIB Object of alaDrcTmPimsmDebug Configuration
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaPimsmDebugTm 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.2.15
This Object is deprecated in favor of alaDrcTmPimsmDebugTm MIB Object of alaDrcTmPimsmDebug Configuration
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaPimsmDebugIpmrm 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.2.16
This Object is deprecated in favor of alaDrcTmPimsmDebugIpmrm MIB Object of alaDrcTmPimsmDebug Configuration
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaPimsmDebugMisc 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.2.17
This Object is deprecated in favor of alaDrcTmPimsmDebugMisc MIB Object of alaDrcTmPimsmDebug Configuration
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaPimsmDebugAll 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.2.18
This Object is deprecated in favor of alaDrcTmPimsmDebugAll MIB Object of alaDrcTmPimsmDebug Configuration
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaPimdmGlobalConfig 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.3
OBJECT IDENTIFIER    

alaPimdmAdminStatus 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.3.1
Administratively enables/disables the PIM-DM protocol on this router.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaPimdmStateRefreshTimeToLive 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.3.2
The TTL to be used by this router's originated State Refresh messages if the data packet's TTL is not recorded.
OBJECT-TYPE    
  Integer32  

alaPimdmStateRefreshLimitInterval 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.3.3
This router will not forward successive State Refresh messages received at less than this interval.
OBJECT-TYPE    
  TimeTicks  

alaPimdmV6AdminStatus 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.1.3.4
Administratively enables/disables the PIM-DM IPv6 protocol on this router.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alcatelIND1PIMMIBConformance 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.2
OBJECT IDENTIFIER    

alcatelIND1PIMMIBCompliances 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.2.1
OBJECT IDENTIFIER    

alaPimsmCompliance 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.2.1.1
The compliance statement for routers running PIM Sparse Mode and implementing the ALCATEL-IND1-PIM MIB.
MODULE-COMPLIANCE    

alaPimdmCompliance 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.2.1.2
The compliance statement for routers running PIM Dense Mode and implementing the ALCATEL-IND1-PIM MIB.
MODULE-COMPLIANCE    

alcatelIND1PIMMIBGroups 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.2.2
OBJECT IDENTIFIER    

alaPimsmConfigMIBGroup 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.2.2.1
A collection of objects to support management of global configuration parameters of PIM Sparse Mode routers.
OBJECT-GROUP    

alaPimsmDebugMIBGroup 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.2.2.2
A collection of optional objects to provide debugging support of PIM Sparse Mode routers.
OBJECT-GROUP    

alaPimdmConfigMIBGroup 1.3.6.1.4.1.6486.800.1.2.1.10.6.1.2.2.3
A collection of objects to support management of global configuration parameters of PIM Dense Mode routers.
OBJECT-GROUP    

Defined Objects

AlaPimsmStaticRPEntry  
SEQUENCE    
  IpAddress as alaPimsmStaticRPGroupAddress  
  IpAddress as alaPimsmStaticRPGroupMask  
  IpAddress as alaPimsmStaticRPAddress  
  RowStatus as alaPimsmStaticRPRowStatus