
| SNMPv2-SMI | SNMPv2-CONF | IF-MIB |
| ALCATEL-IND1-BASE | SNMPv2-TC |
| alcatelIND1PortMIB | 1.3.6.1.4.1.6486.800.1.2.1.5.1 | ||
| This module describes an authoritative enterprise-specific Simple Network Management Protocol (SNMP) Management Information Base (MIB): This group contains the configuration information data for the Ethernet Switching Module. The right to make changes in specification and other information contained in this document without prior notice is reserved. No liability shall be assumed for any incidental, indirect, special, or consequential damages whatsoever arising from or related to this document or the information contained herein. Vendors, end-users, and other interested parties are granted non-exclusive license to use this specification in connection with management of the products for which it is intended to be used. Copyright (C) 1995-2007 Alcatel-Lucent ALL RIGHTS RESERVED WORLDWIDE | |||
| MODULE-IDENTITY | |||
| alcatelIND1PortNotifications | 1.3.6.1.4.1.6486.800.1.2.1.5.1.0 | ||
| OBJECT IDENTIFIER | |||
| ddmNotifications | 1.3.6.1.4.1.6486.800.1.2.1.5.1.0.1 | ||
| OBJECT IDENTIFIER | |||
| ddmTemperatureThresholdViolated | 1.3.6.1.4.1.6486.800.1.2.1.5.1.0.1.0.1 | ||
| This object notifies management station if an SFP/XFP/SFP+ temperature has crossed any threshold or reverted from previous threshold violation for a port represented by ifIndex. It also provides the current realtime value of SFP/XFP/SFP+ temperature. | |||
| NOTIFICATION-TYPE | |||
| ifIndex | |||
| ddmNotificationType | |||
| ddmTemperature | |||
| ddmVoltageThresholdViolated | 1.3.6.1.4.1.6486.800.1.2.1.5.1.0.1.0.2 | ||
| This object notifies management station if an SFP/XFP/SFP+ supply voltage has crossed any threshold or reverted from previous threshold violation for a port represented by ifIndex. It also provides the current realtime value of SFP/XFP/SFP+ supply voltage. | |||
| NOTIFICATION-TYPE | |||
| ifIndex | |||
| ddmNotificationType | |||
| ddmSupplyVoltage | |||
| ddmCurrentThresholdViolated | 1.3.6.1.4.1.6486.800.1.2.1.5.1.0.1.0.3 | ||
| This object notifies management station if an SFP/XFP/SFP+ Tx bias current has crossed any threshold or reverted from previous threshold violation for a port represented by ifIndex. It also provides the current realtime value of SFP/XFP/SFP+ Tx bias current. | |||
| NOTIFICATION-TYPE | |||
| ifIndex | |||
| ddmNotificationType | |||
| ddmTxBiasCurrent | |||
| ddmTxPowerThresholdViolated | 1.3.6.1.4.1.6486.800.1.2.1.5.1.0.1.0.4 | ||
| This object notifies management station if an SFP/XFP/SFP+ Tx output power has crossed any threshold or reverted from previous threshold violation for a port represented by ifIndex. It also provides the current realtime value of SFP/XFP/SFP+ Tx output power. | |||
| NOTIFICATION-TYPE | |||
| ifIndex | |||
| ddmNotificationType | |||
| ddmTxOutputPower | |||
| ddmRxPowerThresholdViolated | 1.3.6.1.4.1.6486.800.1.2.1.5.1.0.1.0.5 | ||
| This object notifies management station if an SFP/XFP/SFP+ Rx optical power has crossed any threshold or reverted from previous threshold violation for a port represented by ifIndex. It also provides the current realtime value of SFP/XFP/SFP+ Rx optical power. | |||
| NOTIFICATION-TYPE | |||
| ifIndex | |||
| ddmNotificationType | |||
| ddmRxOpticalPower | |||
| esmViolationNotifications | 1.3.6.1.4.1.6486.800.1.2.1.5.1.0.2 | ||
| OBJECT IDENTIFIER | |||
| esmViolationRecoveryTimeout | 1.3.6.1.4.1.6486.800.1.2.1.5.1.0.2.0.1 | ||
| This object notifies management station if User-Port ports get re-enabled after esm violation recovery time | |||
| NOTIFICATION-TYPE | |||
| ifIndex | |||
| esmViolationRecoveryNotificationType | |||
| alcatelIND1PortMIBObjects | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1 | ||
| OBJECT IDENTIFIER | |||
| esmConfTrap | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.1 | ||
| OBJECT IDENTIFIER | |||
| esmDrvTrapDrops | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.1.1 | ||
| Partitioned port (separated due to errors). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| physicalPort | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2 | ||
| OBJECT IDENTIFIER | |||
| esmConfTable | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1 | ||
| A list of ESM Physical Port instances. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| EsmConfEntry | |||
| esmConfEntry | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1 | ||
| A ESM Physical Port entry. | |||
| OBJECT-TYPE | |||
| EsmConfEntry | |||
| esmPortSlot | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.1 | ||
| The physical Slot number for this Ethernet Port. Slot number has been added to be used by the private Trap. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| esmPortIF | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.2 | ||
| The on-board interface number for this Ethernet Port. Port Number has been added to be used by the private Trap. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| esmPortAutoSpeed | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.3 | ||
| The automatically detected port line speed of this ESM port. | |||
| OBJECT-TYPE | |||
| INTEGER | speed100(1), speed10(2), speedAuto(3), unknown(4), speed1000(5), speed10000(6) | ||
| esmPortAutoDuplexMode | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.4 | ||
| The automatically detected port duplex mode of this ESM port. Note: GigaEthernet supports only Full duplex mode. Default value for 10/100 = Half duplex mode. | |||
| OBJECT-TYPE | |||
| INTEGER | fullDuplex(1), halfDuplex(2), autoDuplex(3), unknown(4) | ||
| esmPortCfgSpeed | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.5 | ||
| The configured port line speed of this ESM port. | |||
| OBJECT-TYPE | |||
| INTEGER | speed100(1), speed10(2), speedAuto(3), speed1000(5), speed10000(6), speedMax100(8), speedMax1000(9) | ||
| esmPortCfgDuplexMode | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.6 | ||
| The configured port duplex mode of this ESM port. Note: GigaEthernet support only full-duplex. | |||
| OBJECT-TYPE | |||
| INTEGER | fullDuplex(1), halfDuplex(2), autoDuplex(3) | ||
| esmPortCfgIFG | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.7 | ||
| Contains the setting of Inter-Frame Gap (IFG), in bytes for receive and transmit. The range is from 9 to 12 bytes. Note: The default value changed according to the Port type Default Bandwidth value 12 bytes 10Mbps 9600 nsec 100Mbps 960 nsec 1Gbps 96 nsec 10Gbps 9.6 nsec. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| esmPortPauseSlotTime | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.8 | ||
| Indicates the number of microseconds the other end-station waits after the reception of a pause frame. Note: Pause Flow control is not available for 10Mbps. For 100Mbps, the possible value range is 5120 nanosec to 0.3 sec. For 1Gbps, the possible value range is 512 nanosec to 0.03 sec. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| esmPortMaxFloodRate | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.9 | ||
| Broadcast flood threshold type. To set the type, set esmPortMaxFloodRateLimit also. | |||
| OBJECT-TYPE | |||
| INTEGER | mbps(1), percentage(2), pps(3) | ||
| esmPortFloodMcastEnable | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.10 | ||
| Enable/disable the maximum flood rate for multicast. | |||
| OBJECT-TYPE | |||
| INTEGER | disableMulticastFlood(2), enableMulticastFlood(1) | ||
| esmPortCfgMaxFrameSize | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.11 | ||
| Configure the value of the maximum frame size allow. For 10/100: It is a range between 1518(untagged) and 1553 bytes. For GigaEthernet: It is a range between 1518 and 10240 bytes.(OS7700,OS7800,OS8800) It is a range between 1518 and 9216 bytes.(OS6800) | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| esmPortCfgLongEnable | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.12 | ||
| Allow the user to change the maximun Frame size. Note: It is not configurable for 10/100 Ethernet port. | |||
| OBJECT-TYPE | |||
| INTEGER | disable(0), enable(1) | ||
| esmPortCfgRuntEnable | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.13 | ||
| Allow the user to change the minimum Frame size. | |||
| OBJECT-TYPE | |||
| INTEGER | disable(2), enable(3) | ||
| esmPortCfgRuntSize | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.14 | ||
| Configure the value of the minimum frame size allow per ports. The range is 0 to 64. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| esmPortCfgAutoNegotiation | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.15 | ||
| Allow the user to enable or disable the port auto negotiation. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| esmPortCfgCrossover | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.16 | ||
| Allow the user to configure port crossover. | |||
| OBJECT-TYPE | |||
| INTEGER | mdi(1), mdix(2), auto(3) | ||
| esmPortCfgFlow | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.17 | ||
| Use the dot3PauseAdminMode from the standard MIB to configure the flow control. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| esmPortCfgHybridActiveType | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.18 | ||
| This object is only applicable to hybrid ports . It indicates configured active media type.(the operational media type may be different if esmPortCfgHybridMode is configured to be preferredFiber or preferredCopper) For non hybrid ports notapplicable is returned as a status. | |||
| OBJECT-TYPE | |||
| INTEGER | notapplicable(0), fiber(1), copper(2) | ||
| esmPortCfgHybridMode | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.19 | ||
| This object is only applicable to hybrid ports. This allows the user the user to configure the media type with which the port should come up. The user can configure the port to come as copper only or fiber only or either fiber/copper (with preference to one of them). | |||
| OBJECT-TYPE | |||
| INTEGER | notapplicable(0), preferredCopper(1), forcedCopper(2), preferredFiber(3), forcedFiber(4) | ||
| esmPortOperationalHybridType | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.20 | ||
| This object is only applicable to hybrid ports . It indicates the actual media type that has link up and is or will be passing traffic. If link is not present the object will return none(0) value. | |||
| OBJECT-TYPE | |||
| INTEGER | none(0), fiber(1), copper(2) | ||
| esmPortCfgMMULowWaterMarkCellSetLimit | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.21 | ||
| Per-port-per-CoS Head of Line blocking cell limits. Range is 0 - 16383 Firebolt register Offset: 0x006pp30 - 0x37 Bits: 13:0 CellSetLimit , Default: 0x0100 This setting allocates the guaranteed cells for one port's CoSx queue. After cell count over this limit, it will start using dynamic cells in port dynamic space. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..16383 | ||
| esmPortCfgMMUDynamicCellSetLimit | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.22 | ||
| Per-egress port cell-based dynamic (shared buffer pool) memory usage drop and resume thresholds. This sets the limit for which the eight CoS-Qs within a port may share once the LWMCOSCELL limit is exceeded. Range is 0 - 16383 Firebolt register Offset: 0x006pp040 Bits: 13:0 Dynamic CellSetLimit , Chip Default: 0x0400 (1024). The system default value for Dynamic CellSetLimit is 0x100 (256). | |||
| OBJECT-TYPE | |||
| INTEGER | 0..16383 | ||
| esmPortViolationBitMap | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.23 | ||
| A bit map that identifies the set of Application that have blocked a port as a result of a particular violation | |||
| OBJECT-TYPE | |||
| BITS | bEniSecurityBlockPortENI(0), bEniSecurityBlockPortSTP(1), bEniSecurityBlockPortSL(2), bEniSecurityBlockPortQoS(3), bEniSecurityBlockPortUDLD(4), bEniSecurityBlockPortETHBLK(5) | ||
| esmPortViolationClearAll | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.24 | ||
| Clear all port vioaltion | |||
| OBJECT-TYPE | |||
| INTEGER | 0 | ||
| esmPortFloodBcastEnable | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.25 | ||
| Enable/disable the maximum flood rate for Broadcast. | |||
| OBJECT-TYPE | |||
| INTEGER | disableBcastFlood(2), enableBcastFlood(1) | ||
| esmPortFloodUnknownUcastEnable | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.26 | ||
| Enable/disable the maximum flood rate for unknown unicast. | |||
| OBJECT-TYPE | |||
| INTEGER | disableUnknownUcastFlood(2), enableUnknownUcastFlood(1) | ||
| esmPortMaxUnknownUcastFloodRate | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.27 | ||
| Unknown-Unicast flood threshold type. To set the type, set esmPortMaxUnknownUcastFloodRateLimit also | |||
| OBJECT-TYPE | |||
| INTEGER | mbps(1), percentage(2), pps(3) | ||
| esmPortMaxMcastFloodRate | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.28 | ||
| Multicast flood threshold type. To set the type, set esmPortMaxFloodRateLimit also. | |||
| OBJECT-TYPE | |||
| INTEGER | mbps(1), percentage(2), pps(3) | ||
| esmPortMaxFloodRateLimit | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.29 | ||
| The value of the maximum broadcast flood limit. The actual range of the flood limit depends on the port speed. example: Percentage: 1 - 100 Mbps: 1 - 1000 (1G speed) PPS: 244 - 244262 (1G speed) To set the limit, set esmPortMaxFloodRate first | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| esmPortMaxUnknownUcastFloodRateLimit | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.30 | ||
| The value of the maximum unknown-unicast flood limit The actual range of the flood limit depends on the port speed. example: Percentage: 1 - 100 Mbps: 1 - 1000 (1G speed) PPS: 244 - 244262 (1G speed) To set the limit, set esmPortMaxUnknownUcastFloodRate first | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| esmPortMaxMcastFloodRateLimit | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.31 | ||
| The value of the maximum multicast flood limit The actual range of the flood limit depends on the port speed. example: Percentage: 1 - 100 Mbps: 1 - 1000 (1G speed) PPS: 244 - 244262 (1G speed) To set the limit, set esmPortMaxMcastFloodRate first | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| esmPortCfgSFPType | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.1.1.32 | ||
| This object is only applicable to fiber ports. The string indicates the type of SFP/GBIC of active media. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..64) | ||
| alcetherStatsTable | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2 | ||
| A list of Ethernet statistics entries. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AlcetherStatsEntry | |||
| alcetherStatsEntry | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1 | ||
| A collection of statistics kept for a particular Ethernet interface. As an example, an instance of the etherStatsPkts object might be named alcetherStatsPkts.1 | |||
| OBJECT-TYPE | |||
| AlcetherStatsEntry | |||
| alcetherClearStats | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.1 | ||
| Used to Clear all Statistics counters. By default, this object contains zero value. | |||
| OBJECT-TYPE | |||
| INTEGER | default(0), reset(1) | ||
| alcetherLastClearStats | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.2 | ||
| The value of SysUpTime at the time of all the statistics counters are cleared. By default, this object contains a zero value. | |||
| OBJECT-TYPE | |||
| TimeTicks | |||
| alcetherStatsCRCAlignErrors | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.3 | ||
| The total number of packets received that had a length (excluding framing bits, but including FCS octets) of between 64 and 1518 octets, inclusive, but but had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error). | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alcetherStatsRxUndersizePkts | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.4 | ||
| The total number of packets received that were less than 64 octets long (excluding framing bits, but including FCS octets) and were otherwise well formed. | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alcetherStatsTxUndersizePkts | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.5 | ||
| The total number of packets transmitted that were less than 64 octets long (excluding framing bits, but including FCS octets) and were otherwise well formed. | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alcetherStatsTxOversizePkts | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.6 | ||
| The total number of packets transmitted that were longer than 1518 octets long (excluding framing bits, but including FCS octets) and were otherwise well formed. | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alcetherStatsRxJabbers | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.7 | ||
| The total number of packets received that were longer than 1518 octets (excluding framing bits, but including FCS octets), and had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error). Note that this definition of jabber is different than the definition in IEEE-802.3 section 8.2.1.5 (10BASE5) and section 10.3.1.4 (10BASE2). These documents define jabber as the condition where any packet exceeds 20 ms. The allowed range to detect jabber is between 20 ms and 150 ms. | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alcetherStatsRxCollisions | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.8 | ||
| The best estimate of the total number of collisions on this Ethernet segment (in reception). Only for Ethernet Interfaces. The value returned will depend on the location of the RMON probe. Section 8.2.1.3 (10BASE-5) and section 10.3.1.3 (10BASE-2) of IEEE standard 802.3 states that a station must detect a collision, in the receive mode, if three or more stations are transmitting simultaneously. A repeater port must detect a collision when two or more stations are transmitting simultaneously. Thus a probe placed on a repeater port could record more collisions than a probe connected to a station on the same segment would. Probe location plays a much smaller role when considering 10BASE-T. 14.2.1.4 (10BASE-T) of IEEE standard 802.3 defines a collision as the simultaneous presence of signals on the DO and RD circuits (transmitting and receiving at the same time). A 10BASE-T station can only detect collisions when it is transmitting. Thus probes placed on a station and a repeater, should report the same number of collisions. Note also that an RMON probe inside a repeater should ideally report collisions between the repeater and one or more other hosts (transmit collisions as defined by IEEE 802.3k) plus receiver collisions observed on any coax segments to which the repeater is connected. | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alcetherStatsTxCollisions | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.9 | ||
| The best estimate of the total number of collisions on this Ethernet segment (in transmition). Only for Ethernet Interfaces. The value returned will depend on the location of the RMON probe. Section 8.2.1.3 (10BASE-5) and section 10.3.1.3 (10BASE-2) of IEEE standard 802.3 states that a station must detect a collision, in the receive mode, if three or more stations are transmitting simultaneously. A repeater port must detect a collision when two or more stations are transmitting simultaneously. Thus a probe placed on a repeater port could record more collisions than a probe connected to a station on the same segment would. Probe location plays a much smaller role when considering 10BASE-T. 14.2.1.4 (10BASE-T) of IEEE standard 802.3 defines a collision as the simultaneous presence of signals on the DO and RD circuits (transmitting and receiving at the same time). A 10BASE-T station can only detect collisions when it is transmitting. Thus probes placed on a station and a repeater, should report the same number of collisions. Note also that an RMON probe inside a repeater should ideally report collisions between the repeater and one or more other hosts (transmit collisions as defined by IEEE 802.3k) plus receiver collisions observed on any coax segments to which the repeater is connected. | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alcetherStatsPkts64Octets | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.10 | ||
| The total number of packets (including bad packets) received that were 64 octets in length (excluding framing bits but including FCS octets). | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alcetherStatsPkts65to127Octets | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.11 | ||
| The total number of packets (including bad packets) received that were between 65 and 127 octets in length inclusive (excluding framing bits but including FCS octets). | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alcetherStatsPkts128to255Octets | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.12 | ||
| The total number of packets (including bad packets) received that were between 128 and 255 octets in length inclusive (excluding framing bits but including FCS octets). | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alcetherStatsPkts256to511Octets | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.13 | ||
| The total number of packets (including bad packets) received that were between 256 and 511 octets in length inclusive (excluding framing bits but including FCS octets). | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alcetherStatsPkts512to1023Octets | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.14 | ||
| The total number of packets (including bad packets) received that were between 512 and 1023 octets in length inclusive (excluding framing bits but including FCS octets). | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alcetherStatsPkts1024to1518Octets | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.15 | ||
| The total number of packets (including bad packets) received that were between 1024 and 1518 octets in length inclusive (excluding framing bits but including FCS octets). For both Ethernet and GigaEthernet. | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| gigaEtherStatsPkts1519to4095Octets | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.16 | ||
| The total number of packets (including bad packets) received that were between 1519 and 4095 octets in length inclusive (excluding framing bits but including FCS octets). Only for GigaEthernet interfaces | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| gigaEtherStatsPkts4096to9215Octets | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.17 | ||
| The total number of packets (including bad packets) received that were between 4096 and 9215 octets in length inclusive (excluding framing bits but including FCS octets). Only for GigaEthernet interfaces | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alcetherStatsPkts1519to2047Octets | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.18 | ||
| The total number of frames(including error packets) received that were between 1519 and 2047 bytes in length inclusive (excluding framing bits but including FCS bytes). | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alcetherStatsPkts2048to4095Octets | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.19 | ||
| The total number of frames(including error packets) received that were between 2048 and 4095 bytes in length inclusive (excluding framing bits but including FCS bytes). | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alcetherStatsPkts4096Octets | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.20 | ||
| The total number of frames(including error packets) received that were greater than or equal to 4096 bytes in length inclusive (excluding framing bits but including FCS bytes). | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alcetherStatsRxGiantPkts | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.21 | ||
| The total number of frames that are greater than the specified Max length value, with a valid CRC, dropped because too long. | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alcetherStatsRxDribbleNibblePkts | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.22 | ||
| The total number of frames for which a dribble nibble has been received and CRC is correct. | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alcetherStatsRxLongEventPkts | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.23 | ||
| The total number of frames for which the Carrier sense exceeds 50000 bit times for 10 Mbits/sec or 80000 bit times for 100 Mbits/sec. | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alcetherStatsRxVlanTagPkts | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.24 | ||
| The total number of frames for which Type/Length field contains the VLAN protocol identifier (0x8100). | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alcetherStatsRxControlPkts | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.25 | ||
| The total number of frames that were recognized as control frames. | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alcetherStatsRxLenChkErrPkts | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.26 | ||
| The total number of frames for which the frame length field value in the Type/Length field does not match the actual data bytes length and is NOT a type field. | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alcetherStatsRxCodeErrPkts | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.27 | ||
| The total number of frames for which one or more nibbles were signaled as errors during reception of the frame. | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alcetherStatsRxDvEventPkts | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.28 | ||
| The total number of frames for which a RX_DV event (packet not too long enough to be valid packet) has been seen before the correct frame. | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alcetherStatsRxPrevPktDropped | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.29 | ||
| The total number of frames for which a packet has been dropped (because of too small IFG) before the correct frame. | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alcetherStatsTx64Octets | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.30 | ||
| The total number of transmitted frames of 64 bytes. | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alcetherStatsTx65to127Octets | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.31 | ||
| The total number of transmitted frames that were between 65 and 127 bytes in length inclusive (excluding framing bits but including FCS bytes). | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alcetherStatsTx128to255Octets | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.32 | ||
| The total number of transmitted frames that were between 128 and 255 bytes in length inclusive (excluding framing bits but including FCS bytes). | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alcetherStatsTx256to511Octets | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.33 | ||
| The total number of transmitted frames that were between 256 and 511 bytes in length inclusive (excluding framing bits but including FCS bytes). | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alcetherStatsTx512to1023Octets | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.34 | ||
| The total number of transmitted frames that were between 512 and 1023 bytes in length inclusive (excluding framing bits but including FCS bytes). | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alcetherStatsTx1024to1518Octets | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.35 | ||
| The total number of transmitted frames that were between 1024 and 1518 bytes in length inclusive (excluding framing bits but including FCS bytes). | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alcetherStatsTx1519to2047Octets | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.36 | ||
| The total number of transmitted frames that were between 1519 and 2047 bytes in length inclusive (excluding framing bits but including FCS bytes). | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alcetherStatsTx2048to4095Octets | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.37 | ||
| The total number of transmitted frames that were between 2048 and 4095 bytes in length inclusive (excluding framing bits but including FCS bytes). | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alcetherStatsTx4096Octets | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.38 | ||
| The total number of transmitted frames that were greater than or equal to 4096 bytes in length and less than Max frame length (excluding framing bits but including FCS bytes). | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alcetherStatsTxRetryCount | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.39 | ||
| The total number of collisions that the frames faced during transmission attempts. | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alcetherStatsTxVlanTagPkts | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.40 | ||
| The total number of transmitted frames for which Type/Length field contains the VLAN protocol identifier (0x8100). | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alcetherStatsTxControlPkts | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.41 | ||
| The total number of transmitted frames that were recognised as control frames. | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alcetherStatsTxLatePkts | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.42 | ||
| The total number of late collisions that occured beyond the collision window. | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alcetherStatsTxTotalBytesOnWire | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.43 | ||
| The total number of bytes transmitted on wire, including all bytes from collided attempts. | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alcetherStatsTxLenChkErrPkts | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.44 | ||
| The total number of transmitted frames for which the frame length field value in the Type/Length field does not match the actual data bytes length and is NOT a Type field. | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| alcetherStatsTxExcDeferPkts | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.2.1.45 | ||
| The total number of frames that were deferred in excess of 6071 nibble-times in 100 Mbps, 24287 bit-times in 10 Mbps mode. These frames are dropped.(This stat is only in case of Half duplex and excessive defer bit reset). | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| esmHybridConfTable | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.3 | ||
| A list of inactive hybrid port instances. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| EsmHybridConfEntry | |||
| esmHybridConfEntry | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.3.1 | ||
| A ESM Physical Port entry. | |||
| OBJECT-TYPE | |||
| EsmHybridConfEntry | |||
| esmHybridPortCfgSpeed | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.3.1.1 | ||
| The configured port line speed of this ESM port. | |||
| OBJECT-TYPE | |||
| INTEGER | speed100(1), speed10(2), speedAuto(3), speed1000(5), speed10000(6), speedMax100(8), speedMax1000(9) | ||
| esmHybridPortCfgDuplexMode | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.3.1.2 | ||
| The configured port duplex mode of this ESM port. Note: GigaEthernet support only full-duplex. | |||
| OBJECT-TYPE | |||
| INTEGER | fullDuplex(1), halfDuplex(2), autoDuplex(3) | ||
| esmHybridPortCfgAutoNegotiation | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.3.1.3 | ||
| Allow the user to enable or disable the port auto negotiation. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| esmHybridPortCfgCrossover | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.3.1.4 | ||
| Allow the user to configure port crossover. | |||
| OBJECT-TYPE | |||
| INTEGER | mdi(1), mdix(2), auto(3) | ||
| esmHybridPortCfgFlow | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.3.1.5 | ||
| This object is used for flow control of hybrid ports. It is similar to the dot3PauseAdminMode object in dot3PauseTable. It is used to configure pause for fiber media. | |||
| OBJECT-TYPE | |||
| INTEGER | disable(1), enabledXmit(2), enabledRcv(3), enabledXmitAndRcv(4) | ||
| esmHybridPortCfgInactiveType | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.3.1.6 | ||
| This object is only applicable to hybrid ports . It indicates the configured inactive media type. | |||
| OBJECT-TYPE | |||
| INTEGER | fiber(1), copper(2) | ||
| esmHybridPortCfgSFPType | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.3.1.7 | ||
| This object is only applicable to fiber ports. The string indicates the type of SFP/GBIC of active media. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..64) | ||
| alcether10GigTable | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.4 | ||
| A list of 10 Gig specifics entries. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| Alcether10GigEntry | |||
| alcether10GigEntry | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.4.1 | ||
| This table will be populated with the 10 gig only entries. The management interface can use it to specify if A or B is the primary. | |||
| OBJECT-TYPE | |||
| Alcether10GigEntry | |||
| alcether10GigPrimary | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.4.1.1 | ||
| Setting the object to 1 will make phy A as primary, 2- phy B as pirmary. Value 3 should not be set. | |||
| OBJECT-TYPE | |||
| INTEGER | phyAprimary(1), phyBprimary(2), notApplicable(3) | ||
| ddmInfoTable | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5 | ||
| The ddmInfoTable has an entry for each SFP/XFP in the system that supports Digital Diagnostic Monitoring (DDM). The table is indexed by ifIndex. Each row in this table is dynamically added and removed internally by the system based on the presence or absence of DDM capable SFP/XFP components. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| DdmEntry | |||
| ddmInfoEntry | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1 | ||
| Each row represents a particular SFP/XFP that supports Digital Diagnostic Monitoring. Entries are created and deleted internally by the system. | |||
| OBJECT-TYPE | |||
| DdmEntry | |||
| ddmTemperature | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.1 | ||
| The value of ddmTemperature indicates the current temperature of the SFP/XFP in 1000s of degrees Celsius. A value of -200000 indicates this object is not applicable. | |||
| OBJECT-TYPE | |||
| Integer32 | -200000 | -150000..150000 | ||
| ddmTempLowWarning | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.2 | ||
| The value of ddmTempLowWarning indicates the temperature of the SFP/XFP in 1000s of degrees Celsius that triggers a low-warning. A value of -200000 indicates this object is not applicable. | |||
| OBJECT-TYPE | |||
| Integer32 | -200000 | -150000..150000 | ||
| ddmTempLowAlarm | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.3 | ||
| The value of ddmTempLowAlarm indicates the temperature of the SFP/XFP in 1000s of degrees Celsius that triggers a low-alarm. A value of -200000 indicates this object is not applicable. | |||
| OBJECT-TYPE | |||
| Integer32 | -200000 | -150000..150000 | ||
| ddmTempHiWarning | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.4 | ||
| The value of ddmTempHiWarning indicates the temperature of the SFP/XFP in 1000s of degrees Celsius that triggers a hi-warning. A value of -200000 indicates this object is not applicable. | |||
| OBJECT-TYPE | |||
| Integer32 | -200000 | -150000..150000 | ||
| ddmTempHiAlarm | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.5 | ||
| The value of ddmTempHiAlarm indicates the temperature of the SFP/XFP in 1000s of degrees Celsius that triggers a hi-alarm. A value of -200000 indicates this object is not applicable. | |||
| OBJECT-TYPE | |||
| Integer32 | -200000 | -150000..150000 | ||
| ddmSupplyVoltage | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.6 | ||
| The value of ddmSupplyVoltage indicates the current supply voltage of the SFP/XFP in 1000s of Volts (V). A value of -200000 indicates this object is not applicable. | |||
| OBJECT-TYPE | |||
| Integer32 | -200000 | 0..10000 | ||
| ddmSupplyVoltageLowWarning | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.7 | ||
| The value of ddmSupplyVoltageLowWarning indicates the supply voltage of the SFP/XFP in 1000s of Volts (V) that triggers a low-warning. A value of -200000 indicates this object is not applicable. | |||
| OBJECT-TYPE | |||
| Integer32 | -200000 | 0..10000 | ||
| ddmSupplyVoltageLowAlarm | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.8 | ||
| The value of ddmSupplyVoltageLowAlarm indicates the supply voltage of the SFP/XFP in 1000s of Volts (V) that triggers a low-alarm. A value of -200000 indicates this object is not applicable. | |||
| OBJECT-TYPE | |||
| Integer32 | -200000 | 0..10000 | ||
| ddmSupplyVoltageHiWarning | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.9 | ||
| The value of ddmSupplyVoltageHiWarning indicates the supply voltage of the SFP/XFP in 1000s of Volts (V) that triggers a hi-warning. A value of -200000 indicates this object is not applicable. | |||
| OBJECT-TYPE | |||
| Integer32 | -200000 | 0..10000 | ||
| ddmSupplyVoltageHiAlarm | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.10 | ||
| The value of ddmSupplyVoltageHiAlarm indicates the supply voltage of the SFP/XFP in 1000s of Volts (V) that triggers a hi-alarm. A value of -200000 indicates this object is not applicable. | |||
| OBJECT-TYPE | |||
| Integer32 | -200000 | 0..10000 | ||
| ddmTxBiasCurrent | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.11 | ||
| The value of ddmTxBiasCurrent indicates the current Transmit Bias Current of the SFP/XFP in 1000s of milli-Amperes (mA). A value of -200000 indicates this object is not applicable. | |||
| OBJECT-TYPE | |||
| Integer32 | -200000 | 0..10000 | ||
| ddmTxBiasCurrentLowWarning | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.12 | ||
| The value of ddmTxBiasCurrentLowWarning indicates the Transmit Bias Current of the SFP/XFP in 1000s of milli-Amperes (mA) that triggers a low-warning. A value of -200000 indicates this object is not applicable. | |||
| OBJECT-TYPE | |||
| Integer32 | -200000 | 0..10000 | ||
| ddmTxBiasCurrentLowAlarm | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.13 | ||
| The value of ddmTxBiasCurrentLowAlarm indicates the Transmit Bias Current of the SFP/XFP in 1000s of milli-Amperes (mA) that triggers a low-alarm. A value of -200000 indicates this object is not applicable. | |||
| OBJECT-TYPE | |||
| Integer32 | -200000 | 0..10000 | ||
| ddmTxBiasCurrentHiWarning | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.14 | ||
| The value of ddmTxBiasCurrentHiWarning indicates the Transmit Bias Current of the SFP/XFP in 1000s milli-Amperes (mA) that triggers a hi-warning. A value of -200000 indicates this object is not applicable. | |||
| OBJECT-TYPE | |||
| Integer32 | -200000 | 0..10000 | ||
| ddmTxBiasCurrentHiAlarm | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.15 | ||
| The value of ddmTxBiasCurrentHiAlarm indicates the Transmit Bias Current of the SFP/XFP in 1000s milli-Amperes (mA) that triggers a hi-alarm. A value of -200000 indicates this object is not applicable. | |||
| OBJECT-TYPE | |||
| Integer32 | -200000 | 0..10000 | ||
| ddmTxOutputPower | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.16 | ||
| The value of ddmTxOutputPower indicates the current Output Power of the SFP/XFP in 1000s of dBm. A value of -200000 indicates this object is not applicable. | |||
| OBJECT-TYPE | |||
| Integer32 | -200000 | -40000..10000 | ||
| ddmTxOutputPowerLowWarning | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.17 | ||
| The value of ddmTxOutputPowerLowWarning indicates the Output Power of the SFP/XFP in 1000s of dBm that triggers a low-warning. A value of -200000 indicates this object is not applicable. | |||
| OBJECT-TYPE | |||
| Integer32 | -200000 | -40000..10000 | ||
| ddmTxOutputPowerLowAlarm | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.18 | ||
| The value of ddmTxOutputPowerLowAlarm indicates the Output Power of the SFP/XFP in 1000s of dBm that triggers a low-alarm. A value of -200000 indicates this object is not applicable. | |||
| OBJECT-TYPE | |||
| Integer32 | -200000 | -40000..10000 | ||
| ddmTxOutputPowerHiWarning | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.19 | ||
| The value of ddmTxOutputPowerHiWarning indicates the Output Power of the SFP/XFP in 1000s of dBm that triggers a hi-alarm. A value of -200000 indicates this object is not applicable. | |||
| OBJECT-TYPE | |||
| Integer32 | -200000 | -40000..10000 | ||
| ddmTxOutputPowerHiAlarm | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.20 | ||
| The value of ddmTxOutputPowerHiAlarm indicates the Output Power of the SFP/XFP in 1000s of dBm that triggers a hi-alarm. A value of -200000 indicates this object is not applicable. | |||
| OBJECT-TYPE | |||
| Integer32 | -200000 | -40000..10000 | ||
| ddmRxOpticalPower | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.21 | ||
| The value of ddmRxOpticalPower indicates the current Received Optical Power of the SFP/XFP in 1000s of dBm. A value of -200000 indicates this object is not applicable. | |||
| OBJECT-TYPE | |||
| Integer32 | -200000 | -40000..10000 | ||
| ddmRxOpticalPowerLowWarning | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.22 | ||
| The value of ddmRxOpticalPowerLowWarning indicates the Received Optical Power of the SFP/XFP in 1000s of dBm that triggers a low-warning. A value of -200000 indicates this object is not applicable. | |||
| OBJECT-TYPE | |||
| Integer32 | -200000 | -40000..10000 | ||
| ddmRxOpticalPowerLowAlarm | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.23 | ||
| The value of ddmRxOpticalPowerLowAlarm indicates the Received Optical Power of the SFP/XFP in 1000s of dBm that triggers a low-alarm. A value of -200000 indicates this object is not applicable. | |||
| OBJECT-TYPE | |||
| Integer32 | -200000 | -40000..10000 | ||
| ddmRxOpticalPowerHiWarning | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.24 | ||
| The value of ddmRxOpticalPowerHiWarning indicates the Received Optical Power of the SFP/XFP in 1000s of dBm that triggers a hi-warning. A value of -200000 indicates this object is not applicable. | |||
| OBJECT-TYPE | |||
| Integer32 | -200000 | -40000..10000 | ||
| ddmRxOpticalPowerHiAlarm | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.5.1.25 | ||
| The value of ddmRxOpticalPowerHiAlarm indicates the Received Optical Power of the SFP/XFP in 1000s of dBm that triggers a hi-alarm. A value of -200000 indicates this object is not applicable. | |||
| OBJECT-TYPE | |||
| Integer32 | -200000 | -40000..10000 | ||
| esmPortModeTable | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.6 | ||
| A list of ESM Physical Port Mode instances. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| EsmPortModeEntry | |||
| esmPortModeEntry | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.6.1 | ||
| A ESM Physical Port Mode entry. | |||
| OBJECT-TYPE | |||
| EsmPortModeEntry | |||
| esmPortModeIndex | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.6.1.1 | ||
| Valid ni/port values | |||
| OBJECT-TYPE | |||
| INTEGER | 1001..8128 | ||
| esmPortRunningMode | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.6.1.2 | ||
| Currently configured Etna port 25,26 as 10G uplink user port or stacking port. Default is uplink 10G port. User can not set the current mode. | |||
| OBJECT-TYPE | |||
| INTEGER | uplink(1), stackable(2) | ||
| esmPortSavedMode | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.2.6.1.3 | ||
| Next configured Etna port 25,26 as 10G uplink user port or stacking port. At boot up, it has the same value as current esmPortRunningMode. It takes some time to write to the EEPROM. Have at least more than 7 sec between each write operation | |||
| OBJECT-TYPE | |||
| INTEGER | uplink(1), stackable(2) | ||
| esmE2EFlowVlan | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.3 | ||
| 0 - Deleting End-to-End flow control 1-4094 - Enable End-to-End flow control and use the Vlan configured as for End-to-End flow | |||
| OBJECT-TYPE | |||
| INTEGER | 0..4094 | ||
| ddmConfiguration | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.4 | ||
| OBJECT IDENTIFIER | |||
| ddmConfig | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.4.1 | ||
| This object enables/disables DDM software feature in the system. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| ddmTrapConfig | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.4.2 | ||
| This objects enables/disables traps for DDM warning/alarm threshold violations. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| ddmNotificationType | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.4.3 | ||
| This object defines the trap type for monitored DDM parameters. | |||
| OBJECT-TYPE | |||
| INTEGER | clearViolation(1), highAlarm(2), highWarning(3), lowWarning(4), lowAlarm(5) | ||
| esmViolationRecovery | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.5 | ||
| OBJECT IDENTIFIER | |||
| esmViolationRecoveryTrap | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.5.1 | ||
| This objects enables/disables traps for user-port shutdown | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| esmViolationRecoveryTime | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.5.2 | ||
| 0 - Disable the timer 30 - 600 - timeout value to re-enable the UserPort ports | |||
| OBJECT-TYPE | |||
| INTEGER | 0..600 | ||
| esmViolationRecoveryNotificationType | 1.3.6.1.4.1.6486.800.1.2.1.5.1.1.5.3 | ||
| This object defines the trap type for monitored violation-recovery parameters. | |||
| OBJECT-TYPE | |||
| INTEGER | clearViolation(1) | ||
| alcatelIND1PortMIBConformance | 1.3.6.1.4.1.6486.800.1.2.1.5.1.2 | ||
| OBJECT IDENTIFIER | |||
| alcatelIND1PortMIBCompliances | 1.3.6.1.4.1.6486.800.1.2.1.5.1.2.1 | ||
| OBJECT IDENTIFIER | |||
| esmConfPortCompliance | 1.3.6.1.4.1.6486.800.1.2.1.5.1.2.1.1 | ||
| The compliance statement for the configuration of Ethernet ports. | |||
| MODULE-COMPLIANCE | |||
| alcEtherStatsCompliance | 1.3.6.1.4.1.6486.800.1.2.1.5.1.2.1.2 | ||
| The compliance statement for the Statistics of the Ethernet ports. | |||
| MODULE-COMPLIANCE | |||
| alcatelIND1PortMIBGroups | 1.3.6.1.4.1.6486.800.1.2.1.5.1.2.2 | ||
| OBJECT IDENTIFIER | |||
| esmConfMIBGroup | 1.3.6.1.4.1.6486.800.1.2.1.5.1.2.2.1 | ||
| A collection of objects to support the management of global configuration parameters of the Ethernet ports. | |||
| OBJECT-GROUP | |||
| esmDetectedConfMIBGroup | 1.3.6.1.4.1.6486.800.1.2.1.5.1.2.2.2 | ||
| A collection of objects to support the Detected configuration parameters of the Ethernet ports. | |||
| OBJECT-GROUP | |||
| alcEtherStatsMIBGroup | 1.3.6.1.4.1.6486.800.1.2.1.5.1.2.2.3 | ||
| A collection of objects to provide all the statistics related to the Ethernet and GigaEthernert ports. | |||
| OBJECT-GROUP | |||
| alcPortNotificationGroup | 1.3.6.1.4.1.6486.800.1.2.1.5.1.2.2.4 | ||
| The Port MIB Notification Group. | |||
| NOTIFICATION-GROUP | |||
| esmPortModeMIBGroup | 1.3.6.1.4.1.6486.800.1.2.1.5.1.2.2.5 | ||
| A collection of objects to support the management of global configuration parameters of the stacking ports. | |||
| OBJECT-GROUP | |||
| ddmInfoGroup | 1.3.6.1.4.1.6486.800.1.2.1.5.1.2.2.6 | ||
| A collection of objects to provide digital diagnostics information related to SFPs, XFPs, and SFP+s. | |||
| OBJECT-GROUP | |||
| ddmConfigGroup | 1.3.6.1.4.1.6486.800.1.2.1.5.1.2.2.7 | ||
| A collection of objects to allow configuration of DDM and DDM traps. | |||
| OBJECT-GROUP | |||
| ddmNotificationsGroup | 1.3.6.1.4.1.6486.800.1.2.1.5.1.2.2.8 | ||
| A collection of notifications used to indicate DDM threshold violations. | |||
| NOTIFICATION-GROUP | |||
| violationRecoveryGroup | 1.3.6.1.4.1.6486.800.1.2.1.5.1.2.2.9 | ||
| A collection of objects to allow configuration of violationRecovery. | |||
| OBJECT-GROUP | |||
| violationNotificationsGroup | 1.3.6.1.4.1.6486.800.1.2.1.5.1.2.2.10 | ||
| A collection of notifications used to indicate esm violation recovery timeout. | |||
| NOTIFICATION-GROUP | |||
| esmDrvTrapDropsLink | 1.3.6.1.4.1.6486.800.1.3.2.6.0.1 | ||
| When the Ethernet code drops the link because of excessive errors, a Trap is sent. | |||
| NOTIFICATION-TYPE | |||
| esmPortSlot | |||
| esmPortIF | |||
| ifInErrors | |||
| ifOutErrors | |||
| esmDrvTrapDrops | |||
| e2eStackTopoChangeTrap | 1.3.6.1.4.1.6486.800.1.3.2.6.0.2 | ||
| Trap Generated when Stack Topology changes. | |||
| NOTIFICATION-TYPE | |||
| esmE2EFlowVlan | |||
| EsmConfEntry | |||
| SEQUENCE | |||
| Integer32 as esmPortSlot | |||
| Integer32 as esmPortIF | |||
| INTEGER as esmPortAutoSpeed | |||
| INTEGER as esmPortAutoDuplexMode | |||
| INTEGER as esmPortCfgSpeed | |||
| INTEGER as esmPortCfgDuplexMode | |||
| Integer32 as esmPortCfgIFG | |||
| Integer32 as esmPortPauseSlotTime | |||
| INTEGER as esmPortMaxFloodRate | |||
| INTEGER as esmPortFloodMcastEnable | |||
| Integer32 as esmPortCfgMaxFrameSize | |||
| INTEGER as esmPortCfgLongEnable | |||
| INTEGER as esmPortCfgRuntEnable | |||
| Integer32 as esmPortCfgRuntSize | |||
| INTEGER as esmPortCfgAutoNegotiation | |||
| INTEGER as esmPortCfgCrossover | |||
| INTEGER as esmPortCfgFlow | |||
| INTEGER as esmPortCfgHybridActiveType | |||
| INTEGER as esmPortCfgHybridMode | |||
| INTEGER as esmPortOperationalHybridType | |||
| INTEGER as esmPortCfgMMULowWaterMarkCellSetLimit | |||
| INTEGER as esmPortCfgMMUDynamicCellSetLimit | |||
| BITS as esmPortViolationBitMap | |||
| INTEGER as esmPortViolationClearAll | |||
| INTEGER as esmPortFloodBcastEnable | |||
| INTEGER as esmPortFloodUnknownUcastEnable | |||
| INTEGER as esmPortMaxUnknownUcastFloodRate | |||
| INTEGER as esmPortMaxMcastFloodRate | |||
| Integer32 as esmPortMaxFloodRateLimit | |||
| Integer32 as esmPortMaxUnknownUcastFloodRateLimit | |||
| Integer32 as esmPortMaxMcastFloodRateLimit | |||
| DisplayString as esmPortCfgSFPType | |||
| EsmPortModeEntry | |||
| SEQUENCE | |||
| INTEGER as esmPortModeIndex | |||
| INTEGER as esmPortRunningMode | |||
| INTEGER as esmPortSavedMode | |||
| AlcetherStatsEntry | |||
| SEQUENCE | |||
| INTEGER as alcetherClearStats | |||
| TimeTicks as alcetherLastClearStats | |||
| Counter64 as alcetherStatsCRCAlignErrors | |||
| Counter64 as alcetherStatsRxUndersizePkts | |||
| Counter64 as alcetherStatsTxUndersizePkts | |||
| Counter64 as alcetherStatsTxOversizePkts | |||
| Counter64 as alcetherStatsRxJabbers | |||
| Counter64 as alcetherStatsRxCollisions | |||
| Counter64 as alcetherStatsTxCollisions | |||
| Counter64 as alcetherStatsPkts64Octets | |||
| Counter64 as alcetherStatsPkts65to127Octets | |||
| Counter64 as alcetherStatsPkts128to255Octets | |||
| Counter64 as alcetherStatsPkts256to511Octets | |||
| Counter64 as alcetherStatsPkts512to1023Octets | |||
| Counter64 as alcetherStatsPkts1024to1518Octets | |||
| Counter64 as gigaEtherStatsPkts1519to4095Octets | |||
| Counter64 as gigaEtherStatsPkts4096to9215Octets | |||
| Counter64 as alcetherStatsPkts1519to2047Octets | |||
| Counter64 as alcetherStatsPkts2048to4095Octets | |||
| Counter64 as alcetherStatsPkts4096Octets | |||
| Counter64 as alcetherStatsRxGiantPkts | |||
| Counter64 as alcetherStatsRxDribbleNibblePkts | |||
| Counter64 as alcetherStatsRxLongEventPkts | |||
| Counter64 as alcetherStatsRxVlanTagPkts | |||
| Counter64 as alcetherStatsRxControlPkts | |||
| Counter64 as alcetherStatsRxLenChkErrPkts | |||
| Counter64 as alcetherStatsRxCodeErrPkts | |||
| Counter64 as alcetherStatsRxDvEventPkts | |||
| Counter64 as alcetherStatsRxPrevPktDropped | |||
| Counter64 as alcetherStatsTx64Octets | |||
| Counter64 as alcetherStatsTx65to127Octets | |||
| Counter64 as alcetherStatsTx128to255Octets | |||
| Counter64 as alcetherStatsTx256to511Octets | |||
| Counter64 as alcetherStatsTx512to1023Octets | |||
| Counter64 as alcetherStatsTx1024to1518Octets | |||
| Counter64 as alcetherStatsTx1519to2047Octets | |||
| Counter64 as alcetherStatsTx2048to4095Octets | |||
| Counter64 as alcetherStatsTx4096Octets | |||
| Counter64 as alcetherStatsTxRetryCount | |||
| Counter64 as alcetherStatsTxVlanTagPkts | |||
| Counter64 as alcetherStatsTxControlPkts | |||
| Counter64 as alcetherStatsTxLatePkts | |||
| Counter64 as alcetherStatsTxTotalBytesOnWire | |||
| Counter64 as alcetherStatsTxLenChkErrPkts | |||
| Counter64 as alcetherStatsTxExcDeferPkts | |||
| Alcether10GigEntry | |||
| SEQUENCE | |||
| INTEGER as alcether10GigPrimary | |||
| EsmHybridConfEntry | |||
| SEQUENCE | |||
| INTEGER as esmHybridPortCfgSpeed | |||
| INTEGER as esmHybridPortCfgDuplexMode | |||
| INTEGER as esmHybridPortCfgAutoNegotiation | |||
| INTEGER as esmHybridPortCfgCrossover | |||
| INTEGER as esmHybridPortCfgFlow | |||
| INTEGER as esmHybridPortCfgInactiveType | |||
| DisplayString as esmHybridPortCfgSFPType | |||
| DdmEntry | |||
| SEQUENCE | |||
| Integer32 as ddmTemperature | |||
| Integer32 as ddmTempLowWarning | |||
| Integer32 as ddmTempLowAlarm | |||
| Integer32 as ddmTempHiWarning | |||
| Integer32 as ddmTempHiAlarm | |||
| Integer32 as ddmSupplyVoltage | |||
| Integer32 as ddmSupplyVoltageLowWarning | |||
| Integer32 as ddmSupplyVoltageLowAlarm | |||
| Integer32 as ddmSupplyVoltageHiWarning | |||
| Integer32 as ddmSupplyVoltageHiAlarm | |||
| Integer32 as ddmTxBiasCurrent | |||
| Integer32 as ddmTxBiasCurrentLowWarning | |||
| Integer32 as ddmTxBiasCurrentLowAlarm | |||
| Integer32 as ddmTxBiasCurrentHiWarning | |||
| Integer32 as ddmTxBiasCurrentHiAlarm | |||
| Integer32 as ddmTxOutputPower | |||
| Integer32 as ddmTxOutputPowerLowWarning | |||
| Integer32 as ddmTxOutputPowerLowAlarm | |||
| Integer32 as ddmTxOutputPowerHiWarning | |||
| Integer32 as ddmTxOutputPowerHiAlarm | |||
| Integer32 as ddmRxOpticalPower | |||
| Integer32 as ddmRxOpticalPowerLowWarning | |||
| Integer32 as ddmRxOpticalPowerLowAlarm | |||
| Integer32 as ddmRxOpticalPowerHiWarning | |||
| Integer32 as ddmRxOpticalPowerHiAlarm | |||