ALLIEDTELESYN-MIB

File: ALLIEDTELESYN-MIB.mib (113981 bytes)

Imported modules

RFC1155-SMI RFC1213-MIB RFC-1215
RFC-1212 IF-MIB

Imported symbols

enterprises IpAddress Counter
TimeTicks DisplayString PhysAddress
TRAP-TYPE OBJECT-TYPE InterfaceIndex

Defined Objects

alliedTelesyn 1.3.6.1.4.1.207
OBJECT IDENTIFIER    

products 1.3.6.1.4.1.207.1
OBJECT IDENTIFIER    

bridgeRouter 1.3.6.1.4.1.207.1.1
OBJECT IDENTIFIER    

centreCOM-AR300Router 1.3.6.1.4.1.207.1.1.8
OBJECT IDENTIFIER    

centreCOM-AR720Router 1.3.6.1.4.1.207.1.1.11
OBJECT IDENTIFIER    

centreCOM-AR300LRouter 1.3.6.1.4.1.207.1.1.12
OBJECT IDENTIFIER    

centreCOM-AR310Router 1.3.6.1.4.1.207.1.1.13
OBJECT IDENTIFIER    

centreCOM-AR300LURouter 1.3.6.1.4.1.207.1.1.14
OBJECT IDENTIFIER    

centreCOM-AR300URouter 1.3.6.1.4.1.207.1.1.15
OBJECT IDENTIFIER    

centreCOM-AR310URouter 1.3.6.1.4.1.207.1.1.16
OBJECT IDENTIFIER    

centreCOM-AR350Router 1.3.6.1.4.1.207.1.1.17
OBJECT IDENTIFIER    

centreCOM-AR370Router 1.3.6.1.4.1.207.1.1.18
OBJECT IDENTIFIER    

centreCOM-AR330Router 1.3.6.1.4.1.207.1.1.19
OBJECT IDENTIFIER    

centreCOM-AR395Router 1.3.6.1.4.1.207.1.1.20
OBJECT IDENTIFIER    

centreCOM-AR390Router 1.3.6.1.4.1.207.1.1.21
OBJECT IDENTIFIER    

centreCOM-AR370URouter 1.3.6.1.4.1.207.1.1.22
OBJECT IDENTIFIER    

mibObject 1.3.6.1.4.1.207.8
OBJECT IDENTIFIER    

brouterMib 1.3.6.1.4.1.207.8.4
OBJECT IDENTIFIER    

atRouter 1.3.6.1.4.1.207.8.4.4
OBJECT IDENTIFIER    

objects 1.3.6.1.4.1.207.8.4.4.1
OBJECT IDENTIFIER    

boards 1.3.6.1.4.1.207.8.4.4.1.1
OBJECT IDENTIFIER    

ppr-icm-ar023 1.3.6.1.4.1.207.8.4.4.1.1.39
OBJECT IDENTIFIER    

ppr-icm-ar021 1.3.6.1.4.1.207.8.4.4.1.1.40
OBJECT IDENTIFIER    

ppr-icm-ar022 1.3.6.1.4.1.207.8.4.4.1.1.41
OBJECT IDENTIFIER    

ppr-icm-ar025 1.3.6.1.4.1.207.8.4.4.1.1.45
OBJECT IDENTIFIER    

ppr-icm-ar024 1.3.6.1.4.1.207.8.4.4.1.1.46
OBJECT IDENTIFIER    

ppr-ar300 1.3.6.1.4.1.207.8.4.4.1.1.49
OBJECT IDENTIFIER    

ppr-ar300L 1.3.6.1.4.1.207.8.4.4.1.1.52
OBJECT IDENTIFIER    

ppr-ar310 1.3.6.1.4.1.207.8.4.4.1.1.53
OBJECT IDENTIFIER    

ppr-ar300Lu 1.3.6.1.4.1.207.8.4.4.1.1.55
OBJECT IDENTIFIER    

ppr-ar300u 1.3.6.1.4.1.207.8.4.4.1.1.56
OBJECT IDENTIFIER    

ppr-ar310u 1.3.6.1.4.1.207.8.4.4.1.1.57
OBJECT IDENTIFIER    

ppr-ar350 1.3.6.1.4.1.207.8.4.4.1.1.58
OBJECT IDENTIFIER    

ppr-ar720 1.3.6.1.4.1.207.8.4.4.1.1.63
OBJECT IDENTIFIER    

ppr-ar010 1.3.6.1.4.1.207.8.4.4.1.1.67
OBJECT IDENTIFIER    

ppr-ar012 1.3.6.1.4.1.207.8.4.4.1.1.68
OBJECT IDENTIFIER    

ppr-ar011 1.3.6.1.4.1.207.8.4.4.1.1.69
OBJECT IDENTIFIER    

ppr-ar370 1.3.6.1.4.1.207.8.4.4.1.1.70
OBJECT IDENTIFIER    

ppr-ar330 1.3.6.1.4.1.207.8.4.4.1.1.71
OBJECT IDENTIFIER    

ppr-ar395 1.3.6.1.4.1.207.8.4.4.1.1.72
OBJECT IDENTIFIER    

ppr-ar390 1.3.6.1.4.1.207.8.4.4.1.1.73
OBJECT IDENTIFIER    

ppr-ar370u 1.3.6.1.4.1.207.8.4.4.1.1.75
OBJECT IDENTIFIER    

ppr-icm-ar020 1.3.6.1.4.1.207.8.4.4.1.1.76
OBJECT IDENTIFIER    

release 1.3.6.1.4.1.207.8.4.4.1.2
OBJECT IDENTIFIER    

iftypes 1.3.6.1.4.1.207.8.4.4.1.3
OBJECT IDENTIFIER    

iface-eth 1.3.6.1.4.1.207.8.4.4.1.3.1
OBJECT IDENTIFIER    

iface-syn 1.3.6.1.4.1.207.8.4.4.1.3.2
OBJECT IDENTIFIER    

iface-asyn 1.3.6.1.4.1.207.8.4.4.1.3.3
OBJECT IDENTIFIER    

iface-bri 1.3.6.1.4.1.207.8.4.4.1.3.4
OBJECT IDENTIFIER    

iface-pri 1.3.6.1.4.1.207.8.4.4.1.3.5
OBJECT IDENTIFIER    

iface-pots 1.3.6.1.4.1.207.8.4.4.1.3.6
OBJECT IDENTIFIER    

chips 1.3.6.1.4.1.207.8.4.4.1.4
OBJECT IDENTIFIER    

chip-68020-cpu 1.3.6.1.4.1.207.8.4.4.1.4.1
OBJECT IDENTIFIER    

chip-68340-cpu 1.3.6.1.4.1.207.8.4.4.1.4.2
OBJECT IDENTIFIER    

chip-68302-cpu 1.3.6.1.4.1.207.8.4.4.1.4.3
OBJECT IDENTIFIER    

chip-68360-cpu 1.3.6.1.4.1.207.8.4.4.1.4.4
OBJECT IDENTIFIER    

chip-860T-cpu 1.3.6.1.4.1.207.8.4.4.1.4.5
OBJECT IDENTIFIER    

chip-rtc1 1.3.6.1.4.1.207.8.4.4.1.4.21
OBJECT IDENTIFIER    

chip-rtc2 1.3.6.1.4.1.207.8.4.4.1.4.22
OBJECT IDENTIFIER    

chip-rtc3 1.3.6.1.4.1.207.8.4.4.1.4.23
OBJECT IDENTIFIER    

chip-rtc4 1.3.6.1.4.1.207.8.4.4.1.4.24
OBJECT IDENTIFIER    

chip-ram-1mb 1.3.6.1.4.1.207.8.4.4.1.4.31
OBJECT IDENTIFIER    

chip-ram-2mb 1.3.6.1.4.1.207.8.4.4.1.4.32
OBJECT IDENTIFIER    

chip-ram-3mb 1.3.6.1.4.1.207.8.4.4.1.4.33
OBJECT IDENTIFIER    

chip-ram-4mb 1.3.6.1.4.1.207.8.4.4.1.4.34
OBJECT IDENTIFIER    

chip-ram-6mb 1.3.6.1.4.1.207.8.4.4.1.4.36
OBJECT IDENTIFIER    

chip-ram-8mb 1.3.6.1.4.1.207.8.4.4.1.4.38
OBJECT IDENTIFIER    

chip-ram-12mb 1.3.6.1.4.1.207.8.4.4.1.4.42
OBJECT IDENTIFIER    

chip-ram-16mb 1.3.6.1.4.1.207.8.4.4.1.4.46
OBJECT IDENTIFIER    

chip-ram-20mb 1.3.6.1.4.1.207.8.4.4.1.4.50
OBJECT IDENTIFIER    

chip-ram-32mb 1.3.6.1.4.1.207.8.4.4.1.4.62
OBJECT IDENTIFIER    

chip-flash-1mb 1.3.6.1.4.1.207.8.4.4.1.4.71
OBJECT IDENTIFIER    

chip-flash-2mb 1.3.6.1.4.1.207.8.4.4.1.4.72
OBJECT IDENTIFIER    

chip-flash-3mb 1.3.6.1.4.1.207.8.4.4.1.4.73
OBJECT IDENTIFIER    

chip-flash-4mb 1.3.6.1.4.1.207.8.4.4.1.4.74
OBJECT IDENTIFIER    

chip-flash-6mb 1.3.6.1.4.1.207.8.4.4.1.4.76
OBJECT IDENTIFIER    

chip-flash-8mb 1.3.6.1.4.1.207.8.4.4.1.4.78
OBJECT IDENTIFIER    

chip-pem 1.3.6.1.4.1.207.8.4.4.1.4.120
OBJECT IDENTIFIER    

traps 1.3.6.1.4.1.207.8.4.4.2
OBJECT IDENTIFIER    

sysinfo 1.3.6.1.4.1.207.8.4.4.3
OBJECT IDENTIFIER    

modules 1.3.6.1.4.1.207.8.4.4.4
OBJECT IDENTIFIER    

ethernet 1.3.6.1.4.1.207.8.4.4.4.23
OBJECT IDENTIFIER    

ethIntTable 1.3.6.1.4.1.207.8.4.4.4.23.1
The table of Ethernet interfaces.
OBJECT-TYPE    
  SEQUENCE OF  
    EthIntEntry

ethIntEntry 1.3.6.1.4.1.207.8.4.4.4.23.1.1
A single entry in the Ethernet interfaces table.
OBJECT-TYPE    
  EthIntEntry  

ethIntIndex 1.3.6.1.4.1.207.8.4.4.4.23.1.1.1
The ifIndex of the Ethernet interface.
OBJECT-TYPE    
  InterfaceIndex  

ethIntBoardIndex 1.3.6.1.4.1.207.8.4.4.4.23.1.1.2
The index in the arBoardTable of the board on which this Ethernet interface resides. If this Ethernet interface is not found, the value of this object is 0.
OBJECT-TYPE    
  INTEGER  

ethIntBoardPosition 1.3.6.1.4.1.207.8.4.4.4.23.1.1.3
The position on this Ethernet interface's board of this Ethernet interface. If this Ethernet interface is not found, the value of this object is 0.
OBJECT-TYPE    
  INTEGER  

ethIntDuplexMode 1.3.6.1.4.1.207.8.4.4.4.23.1.1.4
The duplex mode of this Ethernet interface. The value unknown is returned when the interface cannot or has not yet made a determination of its duplex mode, or when the interface cannot be found.
OBJECT-TYPE    
  INTEGER full-duplex(1), half-duplex(2), unknown(3)  

cc 1.3.6.1.4.1.207.8.4.4.4.37
OBJECT IDENTIFIER    

ccDetailsTable 1.3.6.1.4.1.207.8.4.4.4.37.1
The table of call details parameters.
OBJECT-TYPE    
  SEQUENCE OF  
    CcDetailsEntry

ccDetailsEntry 1.3.6.1.4.1.207.8.4.4.4.37.1.1
A single entry of ISDN call details. This contains the parameters of a single ISDN call details.
OBJECT-TYPE    
  CcDetailsEntry  

ccDetailsIndex 1.3.6.1.4.1.207.8.4.4.4.37.1.1.1
The index of the call details entry in the call details table. When an entry is created in this table, the index does not have to be written. However, to reference the values that are written, an unused index must be found by reading the index values of the table until a no such object error is returned. Attempting to create a row by using an already used index will result in simply changing the parameters of an existing call details entry.
OBJECT-TYPE    
  INTEGER 1..128  

ccDetailsName 1.3.6.1.4.1.207.8.4.4.4.37.1.1.2
The name of the ISDN call details. This must be unique for all ISDN call details, when comparisons are done ignoring the case of letters. Valid characters in the ISDN call name include 0-9, a-z, A-Z and '-'. A name consisting of all digits is not valid. Setting this object is mandatory on row creation. However, this object cannot be set for an existing call. This is because for the command line interface calls are identified by name. There is one exception. Setting ccDetailsName to an empty string will cause the call details to be deleted.
OBJECT-TYPE    
  DisplayString SIZE(0..15)  

ccDetailsRemoteName 1.3.6.1.4.1.207.8.4.4.4.37.1.1.3
The remote ISDN call name. This name can be referenced by certain other call details parameters related with setting up the Q.931 SETUP message for outgoing calls, or searching for calls for incoming calls. Valid characters in the ISDN remote call name include 0-9, a-z, A-Z and '-'. A remote name consisting of all digits is valid.
OBJECT-TYPE    
  DisplayString SIZE(0..15)  

ccDetailsCalledNumber 1.3.6.1.4.1.207.8.4.4.4.37.1.1.4
The number called when this call details is activated. The number should include all telephone network access codes, country codes and area codes required to make a call from the particular ISDN interface. Setting this object is mandatory on row creation.
OBJECT-TYPE    
  DisplayString SIZE(0..31)  

ccDetailsCallingNumber 1.3.6.1.4.1.207.8.4.4.4.37.1.1.5
The number used as the calling number when this call is activated. The calling number can optionally be placed in the outgoing SETUP message.
OBJECT-TYPE    
  DisplayString SIZE(0..31)  

ccDetailsAlternateNumber 1.3.6.1.4.1.207.8.4.4.4.37.1.1.6
The number called when all retries with the main called number have failed. In this event, the router tries once with the alternate number, then checks the ccDetailsKeepup object to determine whether to try again with the main number.
OBJECT-TYPE    
  DisplayString SIZE(0..31)  

ccDetailsEnabled 1.3.6.1.4.1.207.8.4.4.4.37.1.1.7
Whether this ISDN call is enabled or disabled for incoming and outgoing calls. If the call details entry is disabled, all existing active calls based on this call details entry are left active.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

ccDetailsDirection 1.3.6.1.4.1.207.8.4.4.4.37.1.1.8
The direction for which calls may be made or received using this call details entry.
OBJECT-TYPE    
  INTEGER in-only(1), out-only(2), both(3)  

ccDetailsPrecedence 1.3.6.1.4.1.207.8.4.4.4.37.1.1.9
The precedence of this call details entry in the event of call collision. Call collision occurs when an incoming call for a given details entry is detected while an outgoing call is waiting to complete. This object configures whether the router treats the incoming or outgoing call as having precedence. Since the device at the other end will also probably be experiencing a call collision, the precedence should be configured to the opposite value at the other end. Setting this object is mandatory on row creation.
OBJECT-TYPE    
  INTEGER in(1), out(2)  

ccDetailsHoldupTime 1.3.6.1.4.1.207.8.4.4.4.37.1.1.10
The time, in seconds, that active calls created from this call details should be held up after initial activation. The call will be held up for at least this time, unless cleared from the network. Thus, for example, PPP idle timeouts will not bring the call down.
OBJECT-TYPE    
  INTEGER 0..7200  

ccDetailsPreferredIfIndex 1.3.6.1.4.1.207.8.4.4.4.37.1.1.11
The ifIndex of an ISDN interface on this router which is the preferred ISDN interface on which to make an outgoing call using this call details entry. The ifIndex, if not 0, should reference the ifEntry which contains information about the entire ISDN interface, at the lowest layer. If a channel is not available on this interface, the call can try other interfaces in order to make the call. This object is not used on incoming calls. If the value of this object is set to 0, no interface will be preferred over any other. If the value of this object does not reference the ifEntry for the entire ISDN interface, no interface will be preferred.
OBJECT-TYPE    
  InterfaceIndexOrZero  

ccDetailsRequiredIfIndex 1.3.6.1.4.1.207.8.4.4.4.37.1.1.12
The ifIndex of an ISDN interface on this router which is the required ISDN interface on which to make an outgoing call using this call details entry. The ifIndex, if not 0, must reference the ifEntry which contains information about the entire ISDN interface, at the lowest layer. If a channel is not available on this interface, the call fails. This object is not used on incoming calls. If the value of this object is set to 0, no interface will be required. If the value of this object does not reference the ifEntry for the entire ISDN interface, no interface will be required.
OBJECT-TYPE    
  InterfaceIndexOrZero  

ccDetailsPriority 1.3.6.1.4.1.207.8.4.4.4.37.1.1.13
The priority of calls generated from this call details entry. The priority determines whether calls can be bumped for higher priority calls. The value of priority falls into ranges: 0-19 - call bumped by incoming or outgoing, voice or data calls 20-39 - call bumped by outgoing voice and incoming or outgoing data calls 40-59 - call bumped by emergency voice calls or incoming or outgoing data calls 60-99 - call bumped by emergency voice calls or outgoing data calls. Note that when the call is bumped by a data call, the data call must have higher priority than the call being bumped.
OBJECT-TYPE    
  INTEGER 0..99  

ccDetailsRetryT1 1.3.6.1.4.1.207.8.4.4.4.37.1.1.14
The time in seconds between retries of calls generated from this call details entry.
OBJECT-TYPE    
  INTEGER 5..120  

ccDetailsRetryN1 1.3.6.1.4.1.207.8.4.4.4.37.1.1.15
The number of retries in a retry group for calls generated from this call details entry. Note that the default value means that by default the call will not be retried.
OBJECT-TYPE    
  INTEGER 0..10  

ccDetailsRetryT2 1.3.6.1.4.1.207.8.4.4.4.37.1.1.16
The time in seconds between retry groups for retries of calls generated from this call details entry.
OBJECT-TYPE    
  INTEGER 300..1200  

ccDetailsRetryN2 1.3.6.1.4.1.207.8.4.4.4.37.1.1.17
The number of retry groups for calls generated from this call details entry. Note that the default value means that by default no retry groups will be attempted.
OBJECT-TYPE    
  INTEGER 0..5  

ccDetailsKeepup 1.3.6.1.4.1.207.8.4.4.4.37.1.1.18
A flag indicating whether calls generated from this call details entry should be kept up always. Inspection of this flag takes place when a call is cleared from an external source. If set to 'yes', the call will be retried.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

ccDetailsOutSetupCli 1.3.6.1.4.1.207.8.4.4.4.37.1.1.19
The CLI information placed into outgoing SETUP messages when this call details is used to generate an outgoing call. The value 'off' means that no CLI information in placed in the SETUP message. The value 'calling' means that the calling number from the call details entry is placed in the SETUP message. The value 'interface' means that the Q.931 interface number for the interface and DLC on which the call is made is placed in the SETUP message. The value 'nonumber' means that the CLI information element is placed in the SETUP message with no number information. The network will fill the number in.
OBJECT-TYPE    
  INTEGER off(1), calling(2), interface(3), nonumber(4)  

ccDetailsOutSetupUser 1.3.6.1.4.1.207.8.4.4.4.37.1.1.20
The user-user information placed into outgoing SETUP messages when this call details is used to generate an outgoing call. The value 'off' means that no user-user information in placed in the SETUP message. The value 'local' means that the call name from the call details entry is placed in the SETUP message. The value 'remote' means that the remote call name from the call details entry is placed in the SETUP message.
OBJECT-TYPE    
  INTEGER off(1), local(2), remote(3)  

ccDetailsOutSetupCalledSub 1.3.6.1.4.1.207.8.4.4.4.37.1.1.21
The called subaddress information placed into outgoing SETUP messages when this call details is used to generate an outgoing call. The value 'off' means that no called subaddress information in placed in the SETUP message. The value 'local' means that the call name from the call details entry is placed in the SETUP message. The value 'remote' means that the remote call name from the call details entry is placed in the SETUP message. Note that the action of this object is overridden by the value of the object ccDetailsOutSubaddress.
OBJECT-TYPE    
  INTEGER off(1), local(2), remote(3)  

ccDetailsOutSubaddress 1.3.6.1.4.1.207.8.4.4.4.37.1.1.22
This object gives a way to override the called subaddress information placed into outgoing SETUP messages when this call details is used to generate an outgoing call, as given by the ccDetailsOutSetupCalledSub object. The object is an arbitrary string of ASCII characters, from 0 to 31 characters long.
OBJECT-TYPE    
  DisplayString SIZE(0..31)  

ccDetailsCallback 1.3.6.1.4.1.207.8.4.4.4.37.1.1.23
A flag indicating whether or not to call back the caller when an incoming call is generated from this call details entry. If set to 'yes', the incoming call will be cleared, and after a short delay, an outgoing call will be activated for this call details entry.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

ccDetailsCallbackDelay 1.3.6.1.4.1.207.8.4.4.4.37.1.1.24
The time, in tenths of a second, which the router will wait after clearing an incoming call whose call details entry specified that the caller should be called back before making the return call. The purpose of this object is to allow the user to specify a delay in callback which will allow the network to properly clear the call at both this end and the remote end.
OBJECT-TYPE    
  INTEGER 0..100  

ccDetailsInSetupCalledSubSearch 1.3.6.1.4.1.207.8.4.4.4.37.1.1.25
Determines whether this call details entry is used in a search of call details for an incoming call based on the contents of the called subaddress information in the incoming SETUP message. The value 'off' means that this call details entry is not used in the search. The value 'local' means that the call details entry is used in the search and the called subaddress information is compared with the call details entry name. The value 'remote' means that the call details entry is used in the search and the called subaddress information is compared with the call details entry remote name. A number of searches are carried out until a matching call is found. First a search against the called subaddress in the SETUP message, then a search against the user-user information in the SETUP message, then a search against the calling number information in the SETUP message, then a search for any call that is configured to respond to any incoming call.
OBJECT-TYPE    
  INTEGER off(1), local(2), remote(3)  

ccDetailsInSetupUserSearch 1.3.6.1.4.1.207.8.4.4.4.37.1.1.26
Determines whether this call details entry is used in a search of call details for an incoming call based on the contents of the user-user information in the incoming SETUP message. The value 'off' means that this call details entry is not used in the search. The value 'local' means that the call details entry is used in the search and the user-user information is compared with the call details entry name. The value 'remote' means that the call details entry is used in the search and the user-user information is compared with the call details entry remote name. A number of searches are carried out until a matching call is found. First a search against the called subaddress in the SETUP message, then a search against the user-user information in the SETUP message, then a search against the calling number information in the SETUP message, then a search for any call that is configured to respond to any incoming call.
OBJECT-TYPE    
  INTEGER off(1), local(2), remote(3)  

ccDetailsInSetupCliSearch 1.3.6.1.4.1.207.8.4.4.4.37.1.1.27
Determines whether this call details entry is used in a search of call details for an incoming call based on the contents of the calling number information in the incoming SETUP message. The value 'off' means that this call details entry is not used in the search. The value 'on' means that the call details entry is used in the search and the calling number information is compared with the call details entry called number. The value 'list' means that the call details entry is used in the search and the calling number information is compared with the numbers on the CLI list reference by the object ccDetailsInSetupCliSearchList. The value 'list' cannot be set by an SNMP management entity. Rather the ccDetailsInSetupCliSearchList object should be set to a non-zero value, which will automatically set this object to 'list'. A number of searches are carried out until a matching call is found. First a search against the called subaddress in the SETUP message, then a search against the user-user information in the SETUP message, then a search against the calling number information in the SETUP message, then a search for any call that is configured to respond to any incoming call.
OBJECT-TYPE    
  INTEGER off(1), on(2), list(3)  

ccDetailsInSetupCliSearchList 1.3.6.1.4.1.207.8.4.4.4.37.1.1.28
If the ccDetailsInSetupCliSearch object is set to 'list', this object gives the index of the CLI list to search. The value of CLI list indices is 1..100. The value 0 is returned when the ccDetailsInSetupCliSearch object is not set to 'list'. If the value of this object is set to 0 via SNMP, then the ccDetailsInSetupCliSearch object will be internally set to 'off'. Subsequently setting the value of this object to a non-zero value will set the ccDetailsInSetupCliSearch object to 'list'.
OBJECT-TYPE    
  INTEGER 0..100  

ccDetailsInAnyFlag 1.3.6.1.4.1.207.8.4.4.4.37.1.1.29
Determines whether this call details entry will match any incoming call. After all searched for incoming calls have been carried out based on called subaddress, user-user information and calling number, a search is carried out for the first call found with this flag set to 'yes'.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

ccDetailsInSetupCalledSubCheck 1.3.6.1.4.1.207.8.4.4.4.37.1.1.30
Determines whether to perform a check when an incoming call matches this call details entry based on the contents of the called subaddress information in the incoming SETUP message. The value 'off' means that the check is not carried out. The value 'local' means that the check is carried out and the called subaddress information is compared with the call details entry name. The value 'remote' means that the check is carried out and the called subaddress information is compared with the call details entry remote name. A number of checks are optionally carried out once a matching call is found. The first check is against the called subaddress in the SETUP message, then against the user-user information in the SETUP message, then against the calling number information in the SETUP message.
OBJECT-TYPE    
  INTEGER off(1), local(2), remote(3)  

ccDetailsInSetupUserCheck 1.3.6.1.4.1.207.8.4.4.4.37.1.1.31
Determines whether to perform a check when an incoming call matches this call details entry based on the contents of the user-user information in the incoming SETUP message. The value 'off' means that the check is not carried out. The value 'local' means that the check is carried out and the user-user information is compared with the call details entry name. The value 'remote' means that the check is carried out and the user-user information is compared with the call details entry remote name. A number of checks are optionally carried out once a matching call is found. The first check is against the called subaddress in the SETUP message, then against the user-user information in the SETUP message, then against the calling number information in the SETUP message.
OBJECT-TYPE    
  INTEGER off(1), local(2), remote(3)  

ccDetailsInSetupCliCheck 1.3.6.1.4.1.207.8.4.4.4.37.1.1.32
Determines whether to perform a check and which check to perform when an incoming call matches this call details entry based on the contents of the calling number information in the incoming SETUP message. The value 'off' means that the check is not carried out. The value 'present' means that the check is carried out only if calling number information is present. The value 'required' means that the calling number must be present for the check to pass. When the check is carried out, the calling number information is compared with the numbers in the CLI list referenced by the object ccDetailsInSetupCliCheckList. A number of checks are optionally carried out once a matching call is found. The first check is against the called subaddress in the SETUP message, then against the user-user information in the SETUP message, then against the calling number information in the SETUP message.
OBJECT-TYPE    
  INTEGER off(1), present(2), required(3)  

ccDetailsInSetupCliCheckList 1.3.6.1.4.1.207.8.4.4.4.37.1.1.33
If the ccDetailsInSetupCliCheck object is set to 'present' or 'required', this object gives the index of the CLI list to check against. The value of CLI list indices is 1..100. The value 0 means that no list to check against is defined and the check immediately fails.
OBJECT-TYPE    
  INTEGER 0..100  

ccDetailsUserType 1.3.6.1.4.1.207.8.4.4.4.37.1.1.34
The type of user of this call. The value 'attach' means that users have to attach to this call before the call can be used for outgoing or incoming calls. The value 'ppp' means that for incoming calls only dynamic PPP interfaces will be created whenever this call details entry is matched.
OBJECT-TYPE    
  INTEGER attach(1), ppp(2)  

ccDetailsLoginType 1.3.6.1.4.1.207.8.4.4.4.37.1.1.35
The type of login for calls generated using this call details entry, for incoming calls only. Incoming calls can be configured to go through a logging in phase before the call is brought up. This object defines which login types are used. The value 'none' means don't do a login phase. The value 'userdb' means use the user database on the router to check login parameters. The value 'radius' means use the router's configured RADIUS servers to check the login parameters. The values 'pap-tacacs', 'chap' and 'pap-radius' apply only when the user is 'ppp' and determine how the dynamic PPP interface are configured for authentication. The value 'pap-tacacs' means use PAP to authenticate and use the TACACS server to check the login parameters. The value 'pap-radius' means use PAP to authenticate and use the RADIUS server to check the login parameters. The value 'chap' means use CHAP to authenticate. The value 'tacacs' means use the TACACS server to check login parameters. The value 'all' means use the user database, TACACS and RADIUS to check the login parameters. The login parameters for values 'userdb', 'radius', 'tacacs' and 'all' are determined by the ccDetailsUsername and ccDetailsPassword objects.
OBJECT-TYPE    
  INTEGER none(1), userdb(2), radius(3), pap-tacacs(4), chap(5), pap-radius(6), tacacs(7), all(8)  

ccDetailsUsername 1.3.6.1.4.1.207.8.4.4.4.37.1.1.36
The source of the username when the ccDetailsLoginType object has a value of 'userdb', 'radius', 'tacacs' or 'all'. The value 'none' means no username is defined. The value 'cli' means take the username from the calling number information in the SETUP message. The value 'calledsub' means take the username from the called subaddress information in the SETUP message. The value 'useruser' means take the username from the user-user information in the SETUP message. The value 'callname' means take the username from the call details entry name.
OBJECT-TYPE    
  INTEGER none(1), cli(2), calledsub(3), useruser(4), callname(5)  

ccDetailsPassword 1.3.6.1.4.1.207.8.4.4.4.37.1.1.37
The source of the password when the ccDetailsLoginType object has a value of 'userdb', 'radius', 'tacacs' or 'all'. The value 'none' means no password is defined. The value 'cli' means take the password from the calling number information in the SETUP message. The value 'calledsub' means take the password from the called subaddress information in the SETUP message. The value 'useruser' means take the password from the user-user information in the SETUP message. The value 'callname' means take the password from the call details entry name.
OBJECT-TYPE    
  INTEGER none(1), cli(2), calledsub(3), useruser(4), callname(5)  

ccDetailsBumpDelay 1.3.6.1.4.1.207.8.4.4.4.37.1.1.38
The time, in tenths of a second, which the router will wait after clearing an existing call which has been bumped to make way for a call based on this call details entry.
OBJECT-TYPE    
  INTEGER 0..100  

ccDetailsDataRate 1.3.6.1.4.1.207.8.4.4.4.37.1.1.39
The data rate to use for active calls based on this call details entry. The actual data rate for outgoing calls is determined by both this object and the data rate parameter for the Q.931 interface chosen for the call. If either this object or the interface object specify a rate of 56k, then 56k will be the rate for the call. Otherwise, the default rate of 64k will be used. This allows interoperability between ISDNs which only allow 56k of data on a B channel.
OBJECT-TYPE    
  INTEGER rate-64k(1), rate-56k(2)  

ccDetailsPppTemplate 1.3.6.1.4.1.207.8.4.4.4.37.1.1.40
The PPP template to use when creating dynamic PPP interfaces for calls generated from this call details entry. The value 33 represents a default PPP template, the values 1 to 32 represent PPP templates that are currently defined in the router.
OBJECT-TYPE    
  INTEGER 1..33  

ccDetailsUserModule 1.3.6.1.4.1.207.8.4.4.4.37.1.1.41
The module ID of the user module currently attached to this ISDN call details entry.
OBJECT-TYPE    
  INTEGER  

ccDetailsNumberAttachments 1.3.6.1.4.1.207.8.4.4.4.37.1.1.42
The number of attachments from the user module currently attached to this call details entry. The ccAttachmentsTable gives the actual attachments for each call details entry.
OBJECT-TYPE    
  INTEGER  

ccCliListTable 1.3.6.1.4.1.207.8.4.4.4.37.2
The table of CLI list entries.
OBJECT-TYPE    
  SEQUENCE OF  
    CcCliListEntry

ccCliListEntry 1.3.6.1.4.1.207.8.4.4.4.37.2.1
A single entry in the CLI list table. This contains a single number, as well as index information.
OBJECT-TYPE    
  CcCliListEntry  

ccCliListListIndex 1.3.6.1.4.1.207.8.4.4.4.37.2.1.1
The index of the CLI list. CLI lists from 1 to 100 are defined in the router.
OBJECT-TYPE    
  INTEGER 1..100  

ccCliListEntryIndex 1.3.6.1.4.1.207.8.4.4.4.37.2.1.2
The index of the CLI list entry within the CLI list. The minimum CLI list entry is 1. CLI lists are unlimited in length, although internal memory requirements could result in failure to create a given entry. When creating a row in this table, the entry index should be set to index the first empty row. Only one CLI list row in a given list should be created in any one SNMP message. Attempting to create more than one row will result in failure.
OBJECT-TYPE    
  INTEGER  

ccCliListNumber 1.3.6.1.4.1.207.8.4.4.4.37.2.1.3
The number for this CLI list entry. Setting the number to a zero length string removes the entry from the CLI list, with consequent reshuffling of CLI entry indices. Thus the easiest way to delete an entire CLI list is to repeatedly set the first element in the list to a zero length string. A failure to SET will occur when this is attempted on an empty list.
OBJECT-TYPE    
  DisplayString SIZE(0..31)  

ccActiveCallTable 1.3.6.1.4.1.207.8.4.4.4.37.3
The table of ISDN active calls.
OBJECT-TYPE    
  SEQUENCE OF  
    CcActiveCallEntry

ccActiveCallEntry 1.3.6.1.4.1.207.8.4.4.4.37.3.1
A single entry in the active call table.
OBJECT-TYPE    
  CcActiveCallEntry  

ccActiveCallIndex 1.3.6.1.4.1.207.8.4.4.4.37.3.1.1
The index of the active call. There are 128 possible active calls in the router simultaneously.
OBJECT-TYPE    
  INTEGER 1..128  

ccActiveCallDetailsIndex 1.3.6.1.4.1.207.8.4.4.4.37.3.1.2
The index of the call details entry which generated this active call. Thus the index into the ccDetailsTable for this call.
OBJECT-TYPE    
  INTEGER 1..128  

ccActiveCallIfIndex 1.3.6.1.4.1.207.8.4.4.4.37.3.1.3
The interface index of the interface on which this active call is being made or received. A value of zero indicates that the active has not yet had an interface assigned to it. The ifEntry indexed by this object is the ifEntry for the entire ISDN interface, not the ifEntry for the active call's B channel.
OBJECT-TYPE    
  InterfaceIndexOrZero  

ccActiveCallDataRate 1.3.6.1.4.1.207.8.4.4.4.37.3.1.4
The data rate in use for this active call. This is determined by the call details setting of data rate, the ISDN interface setting for data rate, and the contents of the bearer capability information in the incoming SETUP message.
OBJECT-TYPE    
  INTEGER rate-64k(1), rate-56k(2)  

ccActiveCallState 1.3.6.1.4.1.207.8.4.4.4.37.3.1.5
The state of this active call. The value 'null' indicates that this active call does not actually exist, in other words it is in the process of being created or destroyed. The value 'off' means that the active call is just being activated. The value 'try' means that the active call is attempting to establish. The value 'on' means that the active call is established. The value 'wait' means that the active call is waiting to retry. The value 'await1' means that the active call is waiting for authentication to succeed before becoming established.
OBJECT-TYPE    
  INTEGER null(1), off(2), try(3), on(4), wait(5), await1(6)  

ccActiveCallDirection 1.3.6.1.4.1.207.8.4.4.4.37.3.1.6
The direction of this active call. The value 'in' indicates that this active call is an incoming call, the value 'out' indicates that the active call is an outgoing call. The value 'undefined' indicates that the active call has just been created and a direction has not been assigned to it yet.
OBJECT-TYPE    
  INTEGER in(1), out(2), undefined(3)  

ccActiveCallUserModule 1.3.6.1.4.1.207.8.4.4.4.37.3.1.7
The module ID of the user module attached to this ISDN active call.
OBJECT-TYPE    
  INTEGER  

ccActiveCallUserInstance 1.3.6.1.4.1.207.8.4.4.4.37.3.1.8
The instance of the user module attached to this ISDN active call.
OBJECT-TYPE    
  INTEGER  

ccActiveCallBchannelIndex 1.3.6.1.4.1.207.8.4.4.4.37.3.1.9
The B channel number for this active entry. BRI interfaces have B channels in the range 1..2, PRI interfaces have B channels in the range 1..31, excluding a channel which is the D channel. A value of 0 for this entry means that either a B channel is not currently allocated for this call, or that more than one B channel is allocated. In the second case, the management client will have to walk the B channel allocation table looking for channels with the same active call index as this call's.
OBJECT-TYPE    
  INTEGER 0..31  

ccCallLogTable 1.3.6.1.4.1.207.8.4.4.4.37.4
The table of ISDN call log entries.
OBJECT-TYPE    
  SEQUENCE OF  
    CcCallLogEntry

ccCallLogEntry 1.3.6.1.4.1.207.8.4.4.4.37.4.1
A single entry in the ISDN call log table.
OBJECT-TYPE    
  CcCallLogEntry  

ccCallLogIndex 1.3.6.1.4.1.207.8.4.4.4.37.4.1.1
The index of the call log entry. Since the call log table is dynamic, there is no guarantee that this index will continue to refer to the same log entry over time.
OBJECT-TYPE    
  INTEGER  

ccCallLogName 1.3.6.1.4.1.207.8.4.4.4.37.4.1.2
The name of the call details entry which generated the active call for which this is the log entry.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

ccCallLogState 1.3.6.1.4.1.207.8.4.4.4.37.4.1.3
The state of the log entry. The value 'initial' means that the call is being established. The value 'active' means that the call is currently established. The value 'disconnected' means that the call was disconnected after being established for some time. The value 'cleared' means that the call was cleared abormally while in the establishment phase.
OBJECT-TYPE    
  INTEGER initial(1), active(2), disconnected(3), cleared(4)  

ccCallLogTimeStarted 1.3.6.1.4.1.207.8.4.4.4.37.4.1.4
A string in the format 'dd-mmm-yyyy hh:mm:ss' which gives the start time of the call for which this is the log entry. If the call never reached or has not yet reached the active state, this object will be a zero-length string.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

ccCallLogDirection 1.3.6.1.4.1.207.8.4.4.4.37.4.1.5
The direction of the call for which this is the log entry.
OBJECT-TYPE    
  INTEGER in(1), out(2)  

ccCallLogDuration 1.3.6.1.4.1.207.8.4.4.4.37.4.1.6
The duration in seconds, of the call for which this is the log entry. A value of 0 in this field means either that the call has just started, that the call was cleared before becoming established, or that the call is still active. In other words, a non-zero value is present in this object only for calls which reach establishment and have since been cleared.
OBJECT-TYPE    
  INTEGER  

ccCallLogRemoteNumber 1.3.6.1.4.1.207.8.4.4.4.37.4.1.7
For incoming calls, the calling number, if this was made available in the SETUP message. For outgoing calls, the number dialed. If the number was not available, this object is a zero length string.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

ccAttachmentTable 1.3.6.1.4.1.207.8.4.4.4.37.5
The table of call detail attachment entries.
OBJECT-TYPE    
  SEQUENCE OF  
    CcAttachmentEntry

ccAttachmentEntry 1.3.6.1.4.1.207.8.4.4.4.37.5.1
A single entry in the attachment table.
OBJECT-TYPE    
  CcAttachmentEntry  

ccAttachmentDetailsIndex 1.3.6.1.4.1.207.8.4.4.4.37.5.1.1
The index of the call details entry to which this attachment entry belongs.
OBJECT-TYPE    
  INTEGER 1..128  

ccAttachmentEntryIndex 1.3.6.1.4.1.207.8.4.4.4.37.5.1.2
The index of the attachment entry within the attachment list.
OBJECT-TYPE    
  INTEGER  

ccAttachmentActiveCallIndex 1.3.6.1.4.1.207.8.4.4.4.37.5.1.3
The index of the active call for this attachment. A value of 0 indicates that there is currently no active call for this attachment. A value of 1 to 128 references the active call currently in place for this attachment.
OBJECT-TYPE    
  INTEGER 0..128  

ccAttachmentUserInstance 1.3.6.1.4.1.207.8.4.4.4.37.5.1.4
The instance of the user module attached to the ISDN active call for this attachment. This object should return the same value as the object ccActiveCallUserInstance for the active call indexed by ccAttachmentActiveCallIndex, if this is not 0.
OBJECT-TYPE    
  INTEGER  

ccBchannelTable 1.3.6.1.4.1.207.8.4.4.4.37.6
The table of B channel attachment entries.
OBJECT-TYPE    
  SEQUENCE OF  
    CcBchannelEntry

ccBchannelEntry 1.3.6.1.4.1.207.8.4.4.4.37.6.1
A single entry in the B channel attachment table.
OBJECT-TYPE    
  CcBchannelEntry  

ccBchannelIfIndex 1.3.6.1.4.1.207.8.4.4.4.37.6.1.1
The interface index of the interface which this B channel entry is on. The ifEntry indexed by this object is the ifEntry for the entire ISDN interface, not the ifEntry for the active call's B channel.
OBJECT-TYPE    
  InterfaceIndexOrZero  

ccBchannelChannelIndex 1.3.6.1.4.1.207.8.4.4.4.37.6.1.2
The B channel number for this B channel entry. BRI interfaces have B channels in the range 1..2, PRI interfaces have B channels in the range 1..31, excluding a channel which is the D channel.
OBJECT-TYPE    
  INTEGER 1..31  

ccBchannelAllocated 1.3.6.1.4.1.207.8.4.4.4.37.6.1.3
A flag indicating whether this B channel is actually allocated to a call or not.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

ccBchannelCallType 1.3.6.1.4.1.207.8.4.4.4.37.6.1.4
The type of call on this B channel. If the B channel is not allocated, the call type will be undefined.
OBJECT-TYPE    
  INTEGER undefined(1), data(2), voice(3), x25(4)  

ccBchannelActiveCallIndex 1.3.6.1.4.1.207.8.4.4.4.37.6.1.5
The index of the active call which is currently attached to this B channel. If the value of this object is 0 the channel is either not allocated, or is not allocated to a data call.
OBJECT-TYPE    
  INTEGER 0..128  

ccBchannelPriority 1.3.6.1.4.1.207.8.4.4.4.37.6.1.6
The priority of the call which has this B channel allocated to it. This is in the range 0..99 for data calls, 150 for voice calls and 200 for emergency voice calls. A B channel which is not allocated will have a priority of 0.
OBJECT-TYPE    
  INTEGER  

ccBchannelDirection 1.3.6.1.4.1.207.8.4.4.4.37.6.1.7
The direction of the call which has this B channel allocated to it. If this B channel is not allocated the value will be 'unallocated'.
OBJECT-TYPE    
  INTEGER in(1), out(2), unallocated(3)  

bri 1.3.6.1.4.1.207.8.4.4.4.41
OBJECT IDENTIFIER    

briIntTable 1.3.6.1.4.1.207.8.4.4.4.41.1
The table of BRI interfaces.
OBJECT-TYPE    
  SEQUENCE OF  
    BriIntEntry

briIntEntry 1.3.6.1.4.1.207.8.4.4.4.41.1.1
A single entry in the BRI interfaces table.
OBJECT-TYPE    
  BriIntEntry  

briIntIndex 1.3.6.1.4.1.207.8.4.4.4.41.1.1.1
The ifIndex of the BRI interface.
OBJECT-TYPE    
  INTEGER  

briIntBoardIndex 1.3.6.1.4.1.207.8.4.4.4.41.1.1.2
The index in the arBoardTable of the board on which this BRI interface resides.
OBJECT-TYPE    
  INTEGER  

briIntBoardPosition 1.3.6.1.4.1.207.8.4.4.4.41.1.1.3
The position on this BRI interface's board of this BRI interface.
OBJECT-TYPE    
  INTEGER  

briIntMode 1.3.6.1.4.1.207.8.4.4.4.41.1.1.4
The mode of operation of this BRI interface. The value isdn means that the entire interface is operating as an ISDN interface, the value tdm means that the entire interface is operating as TDM groups and the value mixed means that some channels in the interface are dedicated to ISDN and some to TDM groups.
OBJECT-TYPE    
  INTEGER isdn(1), tdm(2), mixed(3)  

briIntTdmChannelMap 1.3.6.1.4.1.207.8.4.4.4.41.1.1.5
A bit map of the channels in the BRI interface which are dedicated to TDM. Channel B1 has channel map value of 1, channel B2 has a channel map value of 2.
OBJECT-TYPE    
  INTEGER  

briIntIsdnChannelMap 1.3.6.1.4.1.207.8.4.4.4.41.1.1.6
A bit map of the channels in the BRI interface which are dedicated to ISDN. Channel B1 has channel map value of 1, channel B2 has a channel map value of 2.
OBJECT-TYPE    
  INTEGER  

briChanTable 1.3.6.1.4.1.207.8.4.4.4.41.2
The table of channels on BRI interfaces.
OBJECT-TYPE    
  SEQUENCE OF  
    BriChanEntry

briChanEntry 1.3.6.1.4.1.207.8.4.4.4.41.2.1
A single entry in the BRI channels table.
OBJECT-TYPE    
  BriChanEntry  

briChanIntIndex 1.3.6.1.4.1.207.8.4.4.4.41.2.1.1
The ifIndex of the BRI interface.
OBJECT-TYPE    
  INTEGER  

briChanChannelIndex 1.3.6.1.4.1.207.8.4.4.4.41.2.1.2
The channel index of the BRI channel. Channel B1 has index 1, channel B2 has index 2 and the D channel has index 3.
OBJECT-TYPE    
  INTEGER 1..3  

briChanMode 1.3.6.1.4.1.207.8.4.4.4.41.2.1.3
The mode of this BRI channel. The value isdn means that the channel is reserved for use in ISDN calls. The value tdm means that the channel is reserved for use by TDM. For the D channel, this object will always have the value isdn.
OBJECT-TYPE    
  INTEGER isdn(1), tdm(2), none(3)  

briChanState 1.3.6.1.4.1.207.8.4.4.4.41.2.1.4
The state of this BRI channel. The value inactive means that the channel does not currently have an active user, either an ISDN call or an active TDM group. The value active means that the channel is in use, either by an ISDN call or an active TDM group. For the D channel, this object will have the value active if LAPD is using the D channel (either for call control or X.25), or the value inactive otherwise.
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

pri 1.3.6.1.4.1.207.8.4.4.4.42
OBJECT IDENTIFIER    

priIntTable 1.3.6.1.4.1.207.8.4.4.4.42.1
The table of PRI interfaces.
OBJECT-TYPE    
  SEQUENCE OF  
    PriIntEntry

priIntEntry 1.3.6.1.4.1.207.8.4.4.4.42.1.1
A single entry in the PRI interfaces table.
OBJECT-TYPE    
  PriIntEntry  

priIntIndex 1.3.6.1.4.1.207.8.4.4.4.42.1.1.1
The ifIndex of the PRI interface.
OBJECT-TYPE    
  INTEGER  

priIntBoardIndex 1.3.6.1.4.1.207.8.4.4.4.42.1.1.2
The index in the arBoardTable of the board on which this PRI interface resides.
OBJECT-TYPE    
  INTEGER  

priIntBoardPosition 1.3.6.1.4.1.207.8.4.4.4.42.1.1.3
The position on this PRI interface's board of this PRI interface.
OBJECT-TYPE    
  INTEGER  

priIntMode 1.3.6.1.4.1.207.8.4.4.4.42.1.1.4
The mode of operation of this PRI interface. The value isdn means that the entire interface is operating as an ISDN interface, the value tdm means that the entire interface is operating as TDM groups and the value mixed means that some channels in the interface are dedicated to ISDN and some to TDM groups.
OBJECT-TYPE    
  INTEGER isdn(1), tdm(2), mixed(3)  

priIntTdmChannelMap 1.3.6.1.4.1.207.8.4.4.4.42.1.1.5
A bit map of the channels in the PRI interface which are dedicated to TDM. PRI channels are numbered from 0 to 31, 0 is unused, 16 (E1) or 24 (T1) is the D channel. The map values are 2 to the power of the channel number.
OBJECT-TYPE    
  INTEGER  

priIntIsdnChannelMap 1.3.6.1.4.1.207.8.4.4.4.42.1.1.6
A bit map of the channels in the PRI interface which are dedicated to ISDN. PRI channels are numbered from 0 to 31, 0 is unused, 16 (E1) or 24 (T1) is the D channel. The map values are 2 to the power of the channel number.
OBJECT-TYPE    
  INTEGER  

priIntType 1.3.6.1.4.1.207.8.4.4.4.42.1.1.7
The type of primary rate interface. E1 has 30 B + D channel, T1 has 23 B + D channel. If the value unknown is returned for this object, the exact PRI type has not yet been determined.
OBJECT-TYPE    
  INTEGER e1(1), t1(2), unknown(3)  

priChanTable 1.3.6.1.4.1.207.8.4.4.4.42.2
The table of channels on PRI interfaces.
OBJECT-TYPE    
  SEQUENCE OF  
    PriChanEntry

priChanEntry 1.3.6.1.4.1.207.8.4.4.4.42.2.1
A single entry in the PRI channels table.
OBJECT-TYPE    
  PriChanEntry  

priChanIntIndex 1.3.6.1.4.1.207.8.4.4.4.42.2.1.1
The ifIndex of the PRI interface.
OBJECT-TYPE    
  INTEGER  

priChanChannelIndex 1.3.6.1.4.1.207.8.4.4.4.42.2.1.2
The channel index of the PRI channel. Valid channels have indices from 1 to 31. The D channel on an E1 interface has index 16, the D channel on a T1 interface has index 24.
OBJECT-TYPE    
  INTEGER 1..3  

priChanMode 1.3.6.1.4.1.207.8.4.4.4.42.2.1.3
The mode of this PRI channel. The value isdn means that the channel is reserved for use in ISDN calls. The value tdm means that the channel is reserved for use by TDM. For the D channel, this object will usually have the value isdn. An exception is if the interface is running common D channel mode and the D channel is reserved for TDM.
OBJECT-TYPE    
  INTEGER isdn(1), tdm(2), neither(3)  

priChanState 1.3.6.1.4.1.207.8.4.4.4.42.2.1.4
The state of this PRI channel. The value inactive means that the channel does not currently have an active user, either an ISDN call or an active TDM group. The value active means that the channel is in use, either by an ISDN call or an active TDM group.
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

loader 1.3.6.1.4.1.207.8.4.4.4.48
OBJECT IDENTIFIER    

loadTable 1.3.6.1.4.1.207.8.4.4.4.48.1
The table of load parameters, dynamic and static.
OBJECT-TYPE    
  SEQUENCE OF  
    LoadEntry

loadEntry 1.3.6.1.4.1.207.8.4.4.4.48.1.1
A single entry of load parameters. This contains the parameters required to perform a load from the router.
OBJECT-TYPE    
  LoadEntry  

loadIndex 1.3.6.1.4.1.207.8.4.4.4.48.1.1.1
There are two sets of load information, dynamic and static. The dynamic information is used once, then cleared. The static information is used whenever the dynamic information is not available. The dynamic information is also used to indicate the current load parameters when a load is in progress.
OBJECT-TYPE    
  INTEGER static(1), dynamic(2)  

loadServer 1.3.6.1.4.1.207.8.4.4.4.48.1.1.2
The IP address from which load will load.
OBJECT-TYPE    
  IpAddress  

loadDestination 1.3.6.1.4.1.207.8.4.4.4.48.1.1.3
The destination of the file loaded, either flash or nvs memory, or undefined.
OBJECT-TYPE    
  INTEGER undefined(1), nvs(2), flash(3)  

loadFilename 1.3.6.1.4.1.207.8.4.4.4.48.1.1.4
The file name of the file being loaded.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

loadDelay 1.3.6.1.4.1.207.8.4.4.4.48.1.1.5
A delay in seconds between the initiation of the load and the start of the load. This allows for time to set up TFTP servers in cases where the terminal and TFTP server are using the same piece of equipment but will not work simultaneously.
OBJECT-TYPE    
  INTEGER  

loadStatus 1.3.6.1.4.1.207.8.4.4.4.48.2
Status and action object for the load module. The values 1 to 5 are read-only values and reflect the state of the load module. Values 4 and 5 (complete and reset) are 'read-once', that is, if their values are read, either by SNMP or by manager console command, then they will be changed back to idle. The action values (6 and 7) cause a start and stop of the load process respectively. Starting the load can only occur if this field has the values 1, 4, or 5. Stopping the load can only occur is this field has the values 2 or 3. Reading the value of the loadStatus after one of actionstart or actionstop has been set will give one of the values 1 to 5.
OBJECT-TYPE    
  INTEGER idle(1), wait(2), loading(3), complete(4), reset(5), actionstart(6), actionstop(7)  

install 1.3.6.1.4.1.207.8.4.4.4.49
OBJECT IDENTIFIER    

installTable 1.3.6.1.4.1.207.8.4.4.4.49.1
The list of install configurations for the router.
OBJECT-TYPE    
  SEQUENCE OF  
    InstallEntry

installEntry 1.3.6.1.4.1.207.8.4.4.4.49.1.1
An entry in the list of install configurations.
OBJECT-TYPE    
  InstallEntry  

instIndex 1.3.6.1.4.1.207.8.4.4.4.49.1.1.1
The index for the install table. There are three install configurations defined in the router, default, preferred and temporary. The router will attempt to use these in the order temporary, preferred, default when it boots. An install that is undefined will be skipped, an install which points to a file which is not present will be skipped. When the temporary install is used, the information is deleted.
OBJECT-TYPE    
  INTEGER temporary(1), preferred(2), default(3)  

instRelDevice 1.3.6.1.4.1.207.8.4.4.4.49.1.1.2
The device for the release in the install. If the device is flash the file for the release is given in instRelName. Devices none(1) or flash(3) are invalid for the default(3) release.
OBJECT-TYPE    
  INTEGER none(1), eprom(2), flash(3)  

instRelName 1.3.6.1.4.1.207.8.4.4.4.49.1.1.3
The file name for the release in the install, if the instRelDevice is flash(3). If the instRelDevice is none(1) or eprom(2), this object should be a null string.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

instRelMajor 1.3.6.1.4.1.207.8.4.4.4.49.1.1.4
The major release number for this install. This information is obtained by the router when the other elements in the row are set and is thus not directly set by management. If the release number is a.b.c, the major release number is a.
OBJECT-TYPE    
  INTEGER  

instRelMinor 1.3.6.1.4.1.207.8.4.4.4.49.1.1.5
The minor release number for this install. This information is obtained by the router when the other elements in the row are set and is thus not directly set by management. If the release number is a.b.c, the major release number is b.
OBJECT-TYPE    
  INTEGER  

instPatDevice 1.3.6.1.4.1.207.8.4.4.4.49.1.1.6
The device for the patch in the install. The file for the patch is given in instPatName unless the device is none(1).
OBJECT-TYPE    
  INTEGER none(1), flash(3), nvs(4)  

instPatName 1.3.6.1.4.1.207.8.4.4.4.49.1.1.7
The file name for the patch in the install.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

instRelInterim 1.3.6.1.4.1.207.8.4.4.4.49.1.1.8
The interim release number for this install. This information is obtained by the router when the other elements in the row are set and is thus not directly set by management. If the release number is a.b.c, the major release number is c. If the release number is a.b, the interim release number is 0.
OBJECT-TYPE    
  INTEGER  

installHistoryTable 1.3.6.1.4.1.207.8.4.4.4.49.2
The table of descriptions of events in the install history of the router.
OBJECT-TYPE    
  SEQUENCE OF  
    InstallHistoryEntry

installHistoryEntry 1.3.6.1.4.1.207.8.4.4.4.49.2.1
A single line describing part of the install history of the router.
OBJECT-TYPE    
  InstallHistoryEntry  

instHistIndex 1.3.6.1.4.1.207.8.4.4.4.49.2.1.1
The index of this event in the install history. Indices run from 1 to the maximum number. The maximum number is not available as a managed object so this table will have to be traversed in order to find out how large it is.
OBJECT-TYPE    
  INTEGER  

instHistLine 1.3.6.1.4.1.207.8.4.4.4.49.2.1.2
A line of text describing a single event in the install history of the router.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

configFile 1.3.6.1.4.1.207.8.4.4.4.49.3
The name of the file that the router will configure from at boot. The format of the name is the same as that for fileName described above. If the configuration file name is a zero length string, then there is no configuration file defined in the router.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

licenceTable 1.3.6.1.4.1.207.8.4.4.4.49.4
The list of release licences in the router.
OBJECT-TYPE    
  SEQUENCE OF  
    LicenceEntry

licenceEntry 1.3.6.1.4.1.207.8.4.4.4.49.4.1
An entry in the list of release licences.
OBJECT-TYPE    
  LicenceEntry  

licenceIndex 1.3.6.1.4.1.207.8.4.4.4.49.4.1.1
A unique licence index. Licence indices are recalculated every time the router reboots to reflect the current licences on the router. As licences are added, new indices are allocated to the new licences.
OBJECT-TYPE    
  INTEGER  

licenceStatus 1.3.6.1.4.1.207.8.4.4.4.49.4.1.2
The status of the file. When read, this object will always return a value of ok(1), since the object will not exist if the value is deleting(2). Write the value deleting(2) to this object to delete the file.
OBJECT-TYPE    
  INTEGER ok(1), deleting(2)  

licenceRelease 1.3.6.1.4.1.207.8.4.4.4.49.4.1.3
The file name for the release whose licence this is.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

licenceMajor 1.3.6.1.4.1.207.8.4.4.4.49.4.1.4
The major release number for the release whose licence this is.
OBJECT-TYPE    
  INTEGER  

licenceMinor 1.3.6.1.4.1.207.8.4.4.4.49.4.1.5
The minor release number for the release whose licence this is.
OBJECT-TYPE    
  INTEGER  

licencePassword 1.3.6.1.4.1.207.8.4.4.4.49.4.1.6
The password for this release. The password is a string of hex digits.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

licenceExpiry 1.3.6.1.4.1.207.8.4.4.4.49.4.1.7
A human-readable string that gives the expiry date of this licence.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

licenceInterim 1.3.6.1.4.1.207.8.4.4.4.49.4.1.8
The interim release number for the release whose licence this is.
OBJECT-TYPE    
  INTEGER  

createConfigFile 1.3.6.1.4.1.207.8.4.4.4.49.5
The name of a file to create containing the current router configuration. A read from this variable will return the same as the variable configFile. Thus to save the current configuration in the current configuration file, read createConfigFile first, then write the result back to createConfigFile. If this variable is written with the name of an existing file, the file will be replaced with the current configuration.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

file 1.3.6.1.4.1.207.8.4.4.4.56
OBJECT IDENTIFIER    

fileTable 1.3.6.1.4.1.207.8.4.4.4.56.1
A list of all the files in the router's non-volatile storage.
OBJECT-TYPE    
  SEQUENCE OF  
    FileEntry

fileEntry 1.3.6.1.4.1.207.8.4.4.4.56.1.1
An entry in the list of files containing information about a single file in the router.
OBJECT-TYPE    
  FileEntry  

fileIndex 1.3.6.1.4.1.207.8.4.4.4.56.1.1.1
A unique file index. File indices are recalculated every time the router reboots to reflect the current files on the router. As files are added, new indices are allocated to the new files.
OBJECT-TYPE    
  INTEGER  

fileName 1.3.6.1.4.1.207.8.4.4.4.56.1.1.2
The name of the file, in the form . The name is up to eight characters long, the type is up to three characters long.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

fileDevice 1.3.6.1.4.1.207.8.4.4.4.56.1.1.3
The device on which the file resides.
OBJECT-TYPE    
  INTEGER flash(1), nvs(2)  

fileCreationTime 1.3.6.1.4.1.207.8.4.4.4.56.1.1.4
The creation date and time for the file, in the format .
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

fileStatus 1.3.6.1.4.1.207.8.4.4.4.56.1.1.5
The status of the file. When read, this object will always return a value of ok(1), since the object will not exist if the value is deleting(2). Write the value deleting(2) to this object to delete the file.
OBJECT-TYPE    
  INTEGER ok(1), deleting(2)  

fileSize 1.3.6.1.4.1.207.8.4.4.4.56.1.1.6
The size, in bytes, of the file.
OBJECT-TYPE    
  INTEGER  

firewall 1.3.6.1.4.1.207.8.4.4.4.77
OBJECT IDENTIFIER    

firewallTrapMessage 1.3.6.1.4.1.207.8.4.4.4.77.1
The last message sent in a firewall TRAP. This variable is really just a placeholder for the object sent in the firewall TRAP, but can be read independently if required. Note however that a new TRAP will cause this variable to be overwritten.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

firewallTrap 1.3.6.1.4.1.207.8.4.4.4.77.1
A firewall trap is generated when the firewall detects an intrusion or attack and notifies the router manager. Firewall trap notifications are enabled with the command ENABLE FIREWALL NOTIFY=SNMP.
TRAP-TYPE    
  firewallTrapMessage  

arInterfaces 1.3.6.1.4.1.207.8.4.4.5
OBJECT IDENTIFIER    

arBoardMaxIndex 1.3.6.1.4.1.207.8.4.4.5.1
The maximum index of boards in the board table. Index 1 is reserved for the main system board of the router.
OBJECT-TYPE    
  INTEGER  

arBoardTable 1.3.6.1.4.1.207.8.4.4.5.2
The table of boards in the AR router.
OBJECT-TYPE    
  SEQUENCE OF  
    ArBoardEntry

arBoardEntry 1.3.6.1.4.1.207.8.4.4.5.2.1
A single entry in the board table. Each entry consists of information about one board in the router.
OBJECT-TYPE    
  ArBoardEntry  

arBoardIndex 1.3.6.1.4.1.207.8.4.4.5.2.1.1
The index of the board in the board table. Index 1 is reserved for the main system board of the router. Other boards will take index numbers as they are initialised at router startup, or for routers with hot-swap capability, as boards are added to and removed from the router.
OBJECT-TYPE    
  INTEGER  

arBoardId 1.3.6.1.4.1.207.8.4.4.5.2.1.2
The type of board in this board entry. The values of this object are taken from the ppr-xxx object IDs under the boards sub-tree.
OBJECT-TYPE    
  OBJECT IDENTIFIER  

arBoardName 1.3.6.1.4.1.207.8.4.4.5.2.1.3
The name of the board in this board entry. This is a readable string which identifies the board to the manager.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

arBoardRevision 1.3.6.1.4.1.207.8.4.4.5.2.1.4
The manufacturing revision of the board in this board entry. This string has the format Xm-n, where X is P for prototype, or M for manufacturing, m is the major revision number for this board, and n is the field upgrade revision number for this board.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

arBoardSerialNumber 1.3.6.1.4.1.207.8.4.4.5.2.1.5
The serial number of the board in this board entry. Serial numbers are strings of decimal numbers up to 10 digits in length. Each and every serial number is globally unique. It is possible for the serial number of a board to be invalid. In this case the value returned for this object will be '*** Invalid ***'
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

arBoardTotalSlots 1.3.6.1.4.1.207.8.4.4.5.2.1.6
The number of slots on this board. Each slot from 1 to the value of this object may be empty or occupied by another board. By searching the arSlotTable with this board's board index and all values of slot index from 1 to the value of this object, a tree of the boards in this router can be built. The value 0 for this object means that it has no slots.
OBJECT-TYPE    
  INTEGER  

arBoardTotalPositions 1.3.6.1.4.1.207.8.4.4.5.2.1.7
The number of positions on this board. Each position from 1 to the value of this object contains a single router interface. Note that positions are different from slots. An position contains an actual interface while a slot contains a different board which itself may contain interfaces in its positions.
OBJECT-TYPE    
  INTEGER  

arSlotTable 1.3.6.1.4.1.207.8.4.4.5.3
The table of slots in the router, indexed by board index and slot index.
OBJECT-TYPE    
  SEQUENCE OF  
    ArSlotEntry

arSlotEntry 1.3.6.1.4.1.207.8.4.4.5.3.1
A single entry in the board slot table.
OBJECT-TYPE    
  ArSlotEntry  

arSlotBoardIndex 1.3.6.1.4.1.207.8.4.4.5.3.1.1
The index of the board for this slot entry. Index 1 is reserved for the main system board of the router.
OBJECT-TYPE    
  INTEGER  

arSlotSlotIndex 1.3.6.1.4.1.207.8.4.4.5.3.1.2
The index of the slot for this slot entry. Indices start from 1 and are specific to each different board type. There are no gaps in the sequence of slot indices. The maximum value for slot index is given by the value of arBoardTotalSlots for this board.
OBJECT-TYPE    
  INTEGER  

arSlotHeldBoardIndex 1.3.6.1.4.1.207.8.4.4.5.3.1.3
The index of the board held in the slot for this slot entry. This is an index into the arBoardTable. A value of 0 for this object means that the slot is not populated.
OBJECT-TYPE    
  INTEGER  

arSlotDescription 1.3.6.1.4.1.207.8.4.4.5.3.1.4
A description for this slot entry. This is a textual description which gives the manager a clue as to what the slot for this entry is. For example, the slots on an AR 720 have descriptions 'Bay0', 'Bay1' and 'MAC'.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

arInterfaceTable 1.3.6.1.4.1.207.8.4.4.5.4
The table of physical interfaces in the AR router.
OBJECT-TYPE    
  SEQUENCE OF  
    ArInterfaceEntry

arInterfaceEntry 1.3.6.1.4.1.207.8.4.4.5.4.1
A single entry in the interface table. Each entry consists of information about one interface in the router, and is indexed by the board index and the position of the interface on the board.
OBJECT-TYPE    
  ArInterfaceEntry  

arInterfaceBoardIndex 1.3.6.1.4.1.207.8.4.4.5.4.1.1
The index of the board in the board table which contains this interface. Index 1 is reserved for the main system board of the router.
OBJECT-TYPE    
  INTEGER  

arInterfacePosition 1.3.6.1.4.1.207.8.4.4.5.4.1.2
The position of the interface on the board. Each board type will have well-known positions which are the interfaces provided by the board. The number of positions on a given board is given by the object arBoardTotalPositions for this board.
OBJECT-TYPE    
  INTEGER  

arInterfaceIfIndex 1.3.6.1.4.1.207.8.4.4.5.4.1.3
The ifIndex for the interface represented by this entry of the interfaces table. This is the ifIndex of the ifEntry used to represent the physical interface. The value 0 is used for interfaces which don't have an ifIndex.
OBJECT-TYPE    
  InterfaceIndexOrZero  

arInterfaceName 1.3.6.1.4.1.207.8.4.4.5.4.1.4
The name of this interface. This is the name that the manager can use to refer to this interface in entering router commands.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

protocols 1.3.6.1.4.1.207.8.4.4.6
OBJECT IDENTIFIER    

Defined Objects

InterfaceIndexOrZero  
INTEGER 0..2147483647    

ArBoardEntry  
SEQUENCE    
  INTEGER as arBoardIndex  
  OBJECT IDENTIFIER as arBoardId  
  DisplayString as arBoardName  
  DisplayString as arBoardRevision  
  DisplayString as arBoardSerialNumber  
  INTEGER as arBoardTotalSlots  
  INTEGER as arBoardTotalPositions  

ArSlotEntry  
SEQUENCE    
  INTEGER as arSlotBoardIndex  
  INTEGER as arSlotSlotIndex  
  INTEGER as arSlotHeldBoardIndex  
  INTEGER as arSlotDescription  

ArInterfaceEntry  
SEQUENCE    
  INTEGER as arInterfaceBoardIndex  
  INTEGER as arInterfacePosition  
  InterfaceIndexOrZero as arInterfaceIfIndex  
  DisplayString as arInterfaceName  

EthIntEntry  
SEQUENCE    
  InterfaceIndex as ethIntIndex  
  INTEGER as ethIntBoardIndex  
  INTEGER as ethIntBoardPosition  
  INTEGER as ethIntDuplexMode  

CcDetailsEntry  
SEQUENCE    
  INTEGER as ccDetailsIndex  
  DisplayString as ccDetailsName  
  DisplayString as ccDetailsRemoteName  
  DisplayString as ccDetailsCalledNumber  
  DisplayString as ccDetailsCallingNumber  
  DisplayString as ccDetailsAlternateNumber  
  INTEGER as ccDetailsEnabled  
  INTEGER as ccDetailsDirection  
  INTEGER as ccDetailsPrecedence  
  INTEGER as ccDetailsHoldupTime  
  InterfaceIndexOrZero as ccDetailsPreferredIfIndex  
  InterfaceIndexOrZero as ccDetailsRequiredIfIndex  
  INTEGER as ccDetailsPriority  
  INTEGER as ccDetailsRetryT1  
  INTEGER as ccDetailsRetryN1  
  INTEGER as ccDetailsRetryT2  
  INTEGER as ccDetailsRetryN2  
  INTEGER as ccDetailsKeepup  
  INTEGER as ccDetailsOutSetupCli  
  INTEGER as ccDetailsOutSetupUser  
  INTEGER as ccDetailsOutSetupCalledSub  
  DisplayString as ccDetailsOutSubaddress  
  INTEGER as ccDetailsCallback  
  INTEGER as ccDetailsCallbackDelay  
  INTEGER as ccDetailsInSetupCalledSubSearch  
  INTEGER as ccDetailsInSetupUserSearch  
  INTEGER as ccDetailsInSetupCliSearch  
  INTEGER as ccDetailsInSetupCliSearchList  
  INTEGER as ccDetailsInAnyFlag  
  INTEGER as ccDetailsInSetupCalledSubCheck  
  INTEGER as ccDetailsInSetupUserCheck  
  INTEGER as ccDetailsInSetupCliCheck  
  INTEGER as ccDetailsInSetupCliCheckList  
  INTEGER as ccDetailsUserType  
  INTEGER as ccDetailsLoginType  
  INTEGER as ccDetailsUsername  
  INTEGER as ccDetailsPassword  
  INTEGER as ccDetailsBumpDelay  
  INTEGER as ccDetailsDataRate  
  INTEGER as ccDetailsPppTemplate  
  INTEGER as ccDetailsUserModule  
  INTEGER as ccDetailsNumberAttachments  

CcCliListEntry  
SEQUENCE    
  INTEGER as ccCliListListIndex  
  INTEGER as ccCliListEntryIndex  
  DisplayString as ccCliListNumber  

CcActiveCallEntry  
SEQUENCE    
  INTEGER as ccActiveCallIndex  
  INTEGER as ccActiveCallDetailsIndex  
  InterfaceIndexOrZero as ccActiveCallIfIndex  
  INTEGER as ccActiveCallDataRate  
  INTEGER as ccActiveCallState  
  INTEGER as ccActiveCallDirection  
  INTEGER as ccActiveCallUserModule  
  INTEGER as ccActiveCallUserInstance  
  INTEGER as ccActiveCallBchannelIndex  

CcCallLogEntry  
SEQUENCE    
  INTEGER as ccCallLogIndex  
  DisplayString as ccCallLogName  
  INTEGER as ccCallLogState  
  DisplayString as ccCallLogTimeStarted  
  INTEGER as ccCallLogDirection  
  INTEGER as ccCallLogDuration  
  DisplayString as ccCallLogRemoteNumber  

CcAttachmentEntry  
SEQUENCE    
  INTEGER as ccAttachmentDetailsIndex  
  INTEGER as ccAttachmentEntryIndex  
  INTEGER as ccAttachmentActiveCallIndex  
  INTEGER as ccAttachmentUserInstance  

CcBchannelEntry  
SEQUENCE    
  INTEGER as ccBchannelIfIndex  
  INTEGER as ccBchannelChannelIndex  
  INTEGER as ccBchannelAllocated  
  INTEGER as ccBchannelCallType  
  INTEGER as ccBchannelActiveCallIndex  
  INTEGER as ccBchannelPriority  
  INTEGER as ccBchannelDirection  

BriIntEntry  
SEQUENCE    
  INTEGER as briIntIndex  
  INTEGER as briIntBoardIndex  
  INTEGER as briIntBoardPosition  
  INTEGER as briIntMode  
  INTEGER as briIntTdmChannelMap  
  INTEGER as briIntIsdnChannelMap  

BriChanEntry  
SEQUENCE    
  INTEGER as briChanIntIndex  
  INTEGER as briChanChannelIndex  
  INTEGER as briChanMode  
  INTEGER as briChanState  

PriIntEntry  
SEQUENCE    
  INTEGER as priIntIndex  
  INTEGER as priIntBoardIndex  
  INTEGER as priIntBoardPosition  
  INTEGER as priIntMode  
  INTEGER as priIntTdmChannelMap  
  INTEGER as priIntIsdnChannelMap  
  INTEGER as priIntType  

PriChanEntry  
SEQUENCE    
  INTEGER as priChanIntIndex  
  INTEGER as priChanChannelIndex  
  INTEGER as priChanMode  
  INTEGER as priChanState  

LoadEntry  
SEQUENCE    
  INTEGER as loadIndex  
  IpAddress as loadServer  
  INTEGER as loadDestination  
  DisplayString as loadFilename  
  INTEGER as loadDelay  

InstallEntry  
SEQUENCE    
  INTEGER as instIndex  
  INTEGER as instRelDevice  
  DisplayString as instRelName  
  INTEGER as instRelMajor  
  INTEGER as instRelMinor  
  INTEGER as instPatDevice  
  DisplayString as instPatName  
  INTEGER as instRelInterim  

InstallHistoryEntry  
SEQUENCE    
  INTEGER as instHistIndex  
  DisplayString as instHistLine  

LicenceEntry  
SEQUENCE    
  INTEGER as licenceIndex  
  INTEGER as licenceStatus  
  DisplayString as licenceRelease  
  INTEGER as licenceMajor  
  INTEGER as licenceMinor  
  DisplayString as licencePassword  
  DisplayString as licenceExpiry  
  INTEGER as licenceInterim  

FileEntry  
SEQUENCE    
  INTEGER as fileIndex  
  DisplayString as fileName  
  INTEGER as fileDevice  
  DisplayString as fileCreationTime  
  INTEGER as fileStatus  
  INTEGER as fileSize