
| RFC1155-SMI | RFC-1212 | RFC1213-MIB |
| ALTEON-ROOT-MIB |
| enterprises | mgmt | NetworkAddress |
| IpAddress | Counter | Gauge |
| TimeTicks | OBJECT-TYPE | PhysAddress |
| DisplayString | aws-switch |
| agent | 1.3.6.1.4.1.1872.2.5.1 | ||
| OBJECT IDENTIFIER | |||
| agentConfig | 1.3.6.1.4.1.1872.2.5.1.1 | ||
| OBJECT IDENTIFIER | |||
| agSystem | 1.3.6.1.4.1.1872.2.5.1.1.1 | ||
| OBJECT IDENTIFIER | |||
| agApplyConfiguration | 1.3.6.1.4.1.1872.2.5.1.1.1.2 | ||
| This is an action object to apply the changes made to configuration of the switch. By setting the value to apply(2), all the changes made since the last apply are written to the new_config block. other(1) is returned when this object ie read. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), apply(2) | ||
| agSavePending | 1.3.6.1.4.1.1872.2.5.1.1.1.3 | ||
| This object, when read, gives the user information whether an save action is needed and that the configuration has been applied but not saved to the flash. | |||
| OBJECT-TYPE | |||
| INTEGER | saveNeeded(1), noSaveNeeded(2) | ||
| agSaveConfiguration | 1.3.6.1.4.1.1872.2.5.1.1.1.4 | ||
| This is an action object to write current configuration to nonvolatile storage. When issued with the saveActive, the active configuration in flash is saved to backup in flash and then the new configuration is saved to the active configuration in flash. When issued with notSaveActive, the active configuration is NOT saved to the flash and the active configuration is overwritten with the new configuration. ok(1) is returned always when read. | |||
| OBJECT-TYPE | |||
| INTEGER | ok(1), saveActive(2), notSaveActive(3) | ||
| agRevert | 1.3.6.1.4.1.1872.2.5.1.1.1.5 | ||
| This is an action object to revert the unapplied changes made to the switch. By setting the value to revert(2), all the unapplied changes will be reverted. This action will copy the current_config to the new_config block. other(1) is returned when this object is read. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), revert(2) | ||
| agRevertApply | 1.3.6.1.4.1.1872.2.5.1.1.1.6 | ||
| This is an action object to revert the unsaved changes made to the switch. By setting the value to revertApply(2), all the unsaved as well as unapplied changes will be reverted. other(1) is returned when this object is read. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), revertApply(2) | ||
| agReset | 1.3.6.1.4.1.1872.2.5.1.1.1.7 | ||
| This is an action object to reboot the agent. other(1) is returned always when read. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), reset(2) | ||
| agConfigForNxtReset | 1.3.6.1.4.1.1872.2.5.1.1.1.8 | ||
| The configuration information to be loaded from at next reset. The following values are writable: active(2)...active configuration block backup(3)...backup configuration block default(4)..default configuration block | |||
| OBJECT-TYPE | |||
| INTEGER | active(2), backup(3), default(4) | ||
| agImageForNxtReset | 1.3.6.1.4.1.1872.2.5.1.1.1.9 | ||
| The software image to be booted from at next reset. The following values are writable: image1(2)...image 1 image2(3)...image 2 | |||
| OBJECT-TYPE | |||
| INTEGER | image1(2), image2(3) | ||
| agSoftwareVersion | 1.3.6.1.4.1.1872.2.5.1.1.1.10 | ||
| The version of the software image that is currently running on the system in the form of 'major.minor.maintenance.bugfix'. A zero length string is returned if version is not available. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..16) | ||
| agBootVer | 1.3.6.1.4.1.1872.2.5.1.1.1.11 | ||
| The version of the boot code in the form of 'major.minor.bugfix'. A zero length string is returned if version is not available. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..16) | ||
| agImage1Ver | 1.3.6.1.4.1.1872.2.5.1.1.1.12 | ||
| The version of the software image stored in image 1 storage in the form of 'major.minor.bugfix'. A zero length string is returned if version is not available or there is no valid software image. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..128) | ||
| agImage2Ver | 1.3.6.1.4.1.1872.2.5.1.1.1.13 | ||
| The version of the software image stored in image 2 storage in the form of 'major.minor.bugfix'. A zero length string is returned if version is not available or there is no valid software image. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..128) | ||
| agRtcDate | 1.3.6.1.4.1.1872.2.5.1.1.1.14 | ||
| The date on the real time clock in the form of 'mm/dd/yy'. A zero length string is returned if date is not available. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..16) | ||
| agRtcTime | 1.3.6.1.4.1.1872.2.5.1.1.1.15 | ||
| The time on the real time clock in the form of 'hh:mm:ss'. A zero length string is returned if time is not available. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..16) | ||
| agLastSetErrorReason | 1.3.6.1.4.1.1872.2.5.1.1.1.16 | ||
| The error reason of the last SET failure. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..256) | ||
| agCurCfgHttpServerPort | 1.3.6.1.4.1.1872.2.5.1.1.1.17 | ||
| The TCP port number that the HTTP server is listening to in the current_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..65535 | ||
| agNewCfgHttpServerPort | 1.3.6.1.4.1.1872.2.5.1.1.1.18 | ||
| The TCP port number that the HTTP server is listening to in the new_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..65535 | ||
| agCurCfgLoginBanner | 1.3.6.1.4.1.1872.2.5.1.1.1.19 | ||
| The user defined login banner. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..79) | ||
| agNewCfgLoginBanner | 1.3.6.1.4.1.1872.2.5.1.1.1.20 | ||
| The user defined login banner. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..79) | ||
| agCurCfgSmtpHost | 1.3.6.1.4.1.1872.2.5.1.1.1.21 | ||
| The user defined SMTP host. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..127) | ||
| agNewCfgSmtpHost | 1.3.6.1.4.1.1872.2.5.1.1.1.22 | ||
| The user defined SMTP host. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..127) | ||
| agCurCfgConsole | 1.3.6.1.4.1.1872.2.5.1.1.1.23 | ||
| Enable or disable console output of syslog messages. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agNewCfgConsole | 1.3.6.1.4.1.1872.2.5.1.1.1.24 | ||
| Enable or disable console output of syslog messages. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agCurCfgMgmtNetwork | 1.3.6.1.4.1.1872.2.5.1.1.1.25 | ||
| The management network - corresponding to the mnet command of the slb configuration menu. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| agNewCfgMgmtNetwork | 1.3.6.1.4.1.1872.2.5.1.1.1.26 | ||
| The management network - corresponding to the mnet command of the system menu. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| agCurCfgMgmtMask | 1.3.6.1.4.1.1872.2.5.1.1.1.27 | ||
| The management subnet mask - corresponding to the mmask command of the system configuration menu. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| agNewCfgMgmtMask | 1.3.6.1.4.1.1872.2.5.1.1.1.28 | ||
| The management subnet mask - corresponding to the mmask command of the system configuration menu. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| agCurCfgBootp | 1.3.6.1.4.1.1872.2.5.1.1.1.29 | ||
| Enable or disable the use of BootP, as currently configured in the current_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(2), disabled(3) | ||
| agNewCfgBootp | 1.3.6.1.4.1.1872.2.5.1.1.1.30 | ||
| Enable or disable the use of BootP, in the new_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(2), disabled(3) | ||
| agSlotNumber | 1.3.6.1.4.1.1872.2.5.1.1.1.31 | ||
| Identifies the slot in which this switch is installed. If the agent implementing this MIB is not a blade in a chassis this value has no meaning. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..10 | ||
| agCurCfgSnmpTimeout | 1.3.6.1.4.1.1872.2.5.1.1.1.32 | ||
| Once SNMP operations like agApplyConfig, agDiffState and agDumpState, which use the state machine are done the resources used by these operations need to be freed by setting the state back to 'idle' so others can issue the commands via SNMP. agSnmpTimeout indicates the number of minutes before the resources are freed and the state set back to 'idle' if this operation is not performed by the user. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..30 | ||
| agNewCfgSnmpTimeout | 1.3.6.1.4.1.1872.2.5.1.1.1.33 | ||
| Once SNMP operations like agApplyConfig, agDiffState and agDumpState, which use the state machine are done the resources used by these operations need to be freed by setting the state back to 'idle' so others can issue the commands via SNMP. agSnmpTimeout indicates the number of minutes before the resources are freed and the state set back to 'idle' if this operation is not performed by the user. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..30 | ||
| agCurCfgTelnetServerPort | 1.3.6.1.4.1.1872.2.5.1.1.1.34 | ||
| The TCP port number that the telnet server listens for telnet sessions. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..65535 | ||
| agNewCfgTelnetServerPort | 1.3.6.1.4.1.1872.2.5.1.1.1.35 | ||
| The TCP port number that the telnet server listens for telnet sessions. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..65535 | ||
| agClearFlashDump | 1.3.6.1.4.1.1872.2.5.1.1.1.36 | ||
| This is an action object to clear the FLASH dump. ok(1) is returned when this object is read. | |||
| OBJECT-TYPE | |||
| INTEGER | ok(1), clear(2) | ||
| agPortConfig | 1.3.6.1.4.1.1872.2.5.1.1.2 | ||
| OBJECT IDENTIFIER | |||
| agPortTableMaxEnt | 1.3.6.1.4.1.1872.2.5.1.1.2.1 | ||
| The maximum number of rows in the port configuration host table. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| agPortCurCfgTable | 1.3.6.1.4.1.1872.2.5.1.1.2.2 | ||
| The table of port configuration in the current_configuration block. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AgPortCurCfgTableEntry | |||
| agPortCurCfgTableEntry | 1.3.6.1.4.1.1872.2.5.1.1.2.2.1 | ||
| A row in the port table in the current_configuration block. | |||
| OBJECT-TYPE | |||
| AgPortCurCfgTableEntry | |||
| agPortCurCfgIndx | 1.3.6.1.4.1.1872.2.5.1.1.2.2.1.1 | ||
| The index of the row in port configurations table. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| agPortCurCfgState | 1.3.6.1.4.1.1872.2.5.1.1.2.2.1.2 | ||
| This is the state of the port. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(2), disabled(3) | ||
| agPortCurCfgVlanTag | 1.3.6.1.4.1.1872.2.5.1.1.2.2.1.3 | ||
| This is VLAN tag state of the port | |||
| OBJECT-TYPE | |||
| INTEGER | tagged(2), untagged(3) | ||
| agPortCurCfgStp | 1.3.6.1.4.1.1872.2.5.1.1.2.2.1.4 | ||
| This object is used to turn Spanning Tree on or off for the port. | |||
| OBJECT-TYPE | |||
| INTEGER | on(2), off(3) | ||
| agPortCurCfgRmon | 1.3.6.1.4.1.1872.2.5.1.1.2.2.1.5 | ||
| This object is used to turn RMON on or off on the port. | |||
| OBJECT-TYPE | |||
| INTEGER | on(2), off(3) | ||
| agPortCurCfgPVID | 1.3.6.1.4.1.1872.2.5.1.1.2.2.1.6 | ||
| The default VLAN ID for the port. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..4093 | ||
| agPortCurCfgFastEthAutoNeg | 1.3.6.1.4.1.1872.2.5.1.1.2.2.1.7 | ||
| This object is used to turn the autonegotiation on or off for fast Ethernet connection. | |||
| OBJECT-TYPE | |||
| INTEGER | on(2), off(3) | ||
| agPortCurCfgFastEthSpeed | 1.3.6.1.4.1.1872.2.5.1.1.2.2.1.8 | ||
| Selects the port speed for fast Ethernet connection. | |||
| OBJECT-TYPE | |||
| INTEGER | mbs10(2), mbs100(3), mbs10or100(4) | ||
| agPortCurCfgFastEthMode | 1.3.6.1.4.1.1872.2.5.1.1.2.2.1.9 | ||
| This object is used to select port mode for fast Ethernet connection. | |||
| OBJECT-TYPE | |||
| INTEGER | full-duplex(2), half-duplex(3), full-or-half-duplex(4) | ||
| agPortCurCfgFastEthFctl | 1.3.6.1.4.1.1872.2.5.1.1.2.2.1.10 | ||
| Selects the port flow control for fast Ethernet connection. | |||
| OBJECT-TYPE | |||
| INTEGER | transmit(2), receive(3), both(4), none(5) | ||
| agPortCurCfgGigEthAutoNeg | 1.3.6.1.4.1.1872.2.5.1.1.2.2.1.11 | ||
| This object is used to turn the autonegotiation on or off for gigabit Ethernet connection. | |||
| OBJECT-TYPE | |||
| INTEGER | on(2), off(3) | ||
| agPortCurCfgGigEthFctl | 1.3.6.1.4.1.1872.2.5.1.1.2.2.1.12 | ||
| This object is used to select port flow control for gigabit Ethernet connection. | |||
| OBJECT-TYPE | |||
| INTEGER | transmit(2), receive(3), both(4), none(5) | ||
| agPortCurCfgPortName | 1.3.6.1.4.1.1872.2.5.1.1.2.2.1.13 | ||
| The switch port name. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..63) | ||
| agPortCurCfgBwmContract | 1.3.6.1.4.1.1872.2.5.1.1.2.2.1.14 | ||
| The switch port Bandwidth Management contract number. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| agPortCurCfgDiscardNonIPs | 1.3.6.1.4.1.1872.2.5.1.1.2.2.1.15 | ||
| Enable or disable to discard all non-IP traffic on the switch port. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(2), disabled(3) | ||
| agPortCurCfgLinkTrap | 1.3.6.1.4.1.1872.2.5.1.1.2.2.1.16 | ||
| Indicates whether linkUp/linkDown traps should be generated for this interface. By default, this object should have the value enabled(1) for interfaces which do not operate on 'top' of any other interface (as defined in the ifStackTable), and disabled(2) otherwise. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agPortNewCfgTable | 1.3.6.1.4.1.1872.2.5.1.1.2.3 | ||
| The table of port configuration in the new_configuration block. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AgPortNewCfgTableEntry | |||
| agPortNewCfgTableEntry | 1.3.6.1.4.1.1872.2.5.1.1.2.3.1 | ||
| A row in the port configuration table in the new_configuration block. | |||
| OBJECT-TYPE | |||
| AgPortNewCfgTableEntry | |||
| agPortNewCfgIndx | 1.3.6.1.4.1.1872.2.5.1.1.2.3.1.1 | ||
| The index of the row in port configurations table. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| agPortNewCfgState | 1.3.6.1.4.1.1872.2.5.1.1.2.3.1.2 | ||
| This is the state of the port. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(2), disabled(3) | ||
| agPortNewCfgVlanTag | 1.3.6.1.4.1.1872.2.5.1.1.2.3.1.3 | ||
| This is VLAN tag state of the port | |||
| OBJECT-TYPE | |||
| INTEGER | tagged(2), untagged(3) | ||
| agPortNewCfgStp | 1.3.6.1.4.1.1872.2.5.1.1.2.3.1.4 | ||
| This object is used to turn Spanning Tree on or off for the port. | |||
| OBJECT-TYPE | |||
| INTEGER | on(2), off(3) | ||
| agPortNewCfgRmon | 1.3.6.1.4.1.1872.2.5.1.1.2.3.1.5 | ||
| This object is used to turn RMON on or off on the port. | |||
| OBJECT-TYPE | |||
| INTEGER | on(2), off(3) | ||
| agPortNewCfgPVID | 1.3.6.1.4.1.1872.2.5.1.1.2.3.1.6 | ||
| The default VLAN ID for the port. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..4093 | ||
| agPortNewCfgFastEthAutoNeg | 1.3.6.1.4.1.1872.2.5.1.1.2.3.1.7 | ||
| This object is used to turn the autonegotiation on or off for fast Ethernet connection. | |||
| OBJECT-TYPE | |||
| INTEGER | on(2), off(3) | ||
| agPortNewCfgFastEthSpeed | 1.3.6.1.4.1.1872.2.5.1.1.2.3.1.8 | ||
| Selects the port speed for fast Ethernet connection. | |||
| OBJECT-TYPE | |||
| INTEGER | mbs10(2), mbs100(3), mbs10or100(4) | ||
| agPortNewCfgFastEthMode | 1.3.6.1.4.1.1872.2.5.1.1.2.3.1.9 | ||
| This object is used to select port mode for fast Ethernet connection. | |||
| OBJECT-TYPE | |||
| INTEGER | full-duplex(2), half-duplex(3), full-or-half-duplex(4) | ||
| agPortNewCfgFastEthFctl | 1.3.6.1.4.1.1872.2.5.1.1.2.3.1.10 | ||
| Selects the port flow control for fast Ethernet connection. | |||
| OBJECT-TYPE | |||
| INTEGER | transmit(2), receive(3), both(4), none(5) | ||
| agPortNewCfgGigEthAutoNeg | 1.3.6.1.4.1.1872.2.5.1.1.2.3.1.11 | ||
| This object is used to turn the autonegotiation on or off for gigabit Ethernet connection. | |||
| OBJECT-TYPE | |||
| INTEGER | on(2), off(3) | ||
| agPortNewCfgGigEthFctl | 1.3.6.1.4.1.1872.2.5.1.1.2.3.1.12 | ||
| This object is used to select port flow control for gigabit Ethernet connection. | |||
| OBJECT-TYPE | |||
| INTEGER | transmit(2), receive(3), both(4), none(5) | ||
| agPortNewCfgPortName | 1.3.6.1.4.1.1872.2.5.1.1.2.3.1.13 | ||
| The switch port name. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..63) | ||
| agPortNewCfgBwmContract | 1.3.6.1.4.1.1872.2.5.1.1.2.3.1.14 | ||
| The switch port Bandwidth Management contract number. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| agPortNewCfgDiscardNonIPs | 1.3.6.1.4.1.1872.2.5.1.1.2.3.1.15 | ||
| Enable or disable to discard all non-IP traffic on the switch port. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(2), disabled(3) | ||
| agPortNewCfgLinkTrap | 1.3.6.1.4.1.1872.2.5.1.1.2.3.1.16 | ||
| Indicates whether linkUp/linkDown traps should be generated for this interface. By default, this object should have the value enabled(1) for interfaces which do not operate on 'top' of any other interface (as defined in the ifStackTable), and disabled(2) otherwise. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agRadiusConfig | 1.3.6.1.4.1.1872.2.5.1.1.3 | ||
| OBJECT IDENTIFIER | |||
| radCurCfgPrimaryIpAddr | 1.3.6.1.4.1.1872.2.5.1.1.3.1 | ||
| The IP address of the Primary RADIUS server. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| radNewCfgPrimaryIpAddr | 1.3.6.1.4.1.1872.2.5.1.1.3.2 | ||
| The IP address of the Primary RADIUS server. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| radCurCfgSecondaryIpAddr | 1.3.6.1.4.1.1872.2.5.1.1.3.3 | ||
| The IP address of the Secondary RADIUS server. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| radNewCfgSecondaryIpAddr | 1.3.6.1.4.1.1872.2.5.1.1.3.4 | ||
| The IP address of the Secondary RADIUS server. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| radCurCfgPort | 1.3.6.1.4.1.1872.2.5.1.1.3.5 | ||
| Specify the RADIUS port number. | |||
| OBJECT-TYPE | |||
| INTEGER | 1500..3000 | ||
| radNewCfgPort | 1.3.6.1.4.1.1872.2.5.1.1.3.6 | ||
| Speicfy the RADIUS port number. | |||
| OBJECT-TYPE | |||
| INTEGER | 1500..3000 | ||
| radCurCfgTimeout | 1.3.6.1.4.1.1872.2.5.1.1.3.7 | ||
| The maximum number of seconds before resending authentication to RADIUS server. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..10 | ||
| radNewCfgTimeout | 1.3.6.1.4.1.1872.2.5.1.1.3.8 | ||
| The maximum number of seconds before resending authentication to RADIUS server. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..10 | ||
| radCurCfgRetries | 1.3.6.1.4.1.1872.2.5.1.1.3.9 | ||
| Number of retries to the RADIUS server. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..3 | ||
| radNewCfgRetries | 1.3.6.1.4.1.1872.2.5.1.1.3.10 | ||
| Number of retries to the RADIUS server. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..3 | ||
| radCurCfgState | 1.3.6.1.4.1.1872.2.5.1.1.3.11 | ||
| Enable or disbale RADIUS authentication. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(2), disabled(3) | ||
| radNewCfgState | 1.3.6.1.4.1.1872.2.5.1.1.3.12 | ||
| Enable or disable RADIUS authentication. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(2), disabled(3) | ||
| radCurCfgAuthenString | 1.3.6.1.4.1.1872.2.5.1.1.3.13 | ||
| The RADIUS authentication string. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..32) | ||
| radNewCfgAuthenString | 1.3.6.1.4.1.1872.2.5.1.1.3.14 | ||
| The RADIUS authentication string. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..32) | ||
| radCurCfgTelnet | 1.3.6.1.4.1.1872.2.5.1.1.3.15 | ||
| Enable or disbale RADIUS backdoor for telnet. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| radNewCfgTelnet | 1.3.6.1.4.1.1872.2.5.1.1.3.16 | ||
| Enable or disable RADIUS backdoor for telnet. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agNTP | 1.3.6.1.4.1.1872.2.5.1.1.4 | ||
| OBJECT IDENTIFIER | |||
| agCurCfgNTPServer | 1.3.6.1.4.1.1872.2.5.1.1.4.1 | ||
| The NTP Server Address. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| agNewCfgNTPServer | 1.3.6.1.4.1.1872.2.5.1.1.4.2 | ||
| The NTP Server Address. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| agCurCfgNTPResyncInterval | 1.3.6.1.4.1.1872.2.5.1.1.4.3 | ||
| The NTP Server resync interval in minutes. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..2880 | ||
| agNewCfgNTPResyncInterval | 1.3.6.1.4.1.1872.2.5.1.1.4.4 | ||
| The NTP Server resync interval in minutes. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..2880 | ||
| agCurCfgNTPTzoneHHMM | 1.3.6.1.4.1.1872.2.5.1.1.4.5 | ||
| The NTP Server timezone offset from GMT formatted as (+/-)HH:MM. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..6) | ||
| agNewCfgNTPTzoneHHMM | 1.3.6.1.4.1.1872.2.5.1.1.4.6 | ||
| The NTP Server timezone offset from GMT formatted as (+/-)HH:MM. The valid range is from -12:59 to +12:59. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..6) | ||
| agCurCfgNTPDlight | 1.3.6.1.4.1.1872.2.5.1.1.4.7 | ||
| Enable/disable daylight savings time. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agNewCfgNTPDlight | 1.3.6.1.4.1.1872.2.5.1.1.4.8 | ||
| Enable/disable daylight savings time. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agCurCfgNTPService | 1.3.6.1.4.1.1872.2.5.1.1.4.9 | ||
| Enable/disable NTP Service. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agNewCfgNTPService | 1.3.6.1.4.1.1872.2.5.1.1.4.10 | ||
| Enable/disable NTP Service. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agSyslog | 1.3.6.1.4.1.1872.2.5.1.1.5 | ||
| OBJECT IDENTIFIER | |||
| agCurCfgSyslogHost | 1.3.6.1.4.1.1872.2.5.1.1.5.1 | ||
| The syslog host IP address, as currently configured in the current_configuration block. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| agNewCfgSyslogHost | 1.3.6.1.4.1.1872.2.5.1.1.5.2 | ||
| The syslog host IP address, in the new_configuration block. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| agCurCfgSyslog2Host | 1.3.6.1.4.1.1872.2.5.1.1.5.3 | ||
| The second syslog host IP address, as currently configured in the current_configuration block. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| agNewCfgSyslog2Host | 1.3.6.1.4.1.1872.2.5.1.1.5.4 | ||
| The second syslog host IP address, in the new_configuration block. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| agCurCfgSyslogFac | 1.3.6.1.4.1.1872.2.5.1.1.5.5 | ||
| The facility of syslog host in the current_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | local0(1), local1(2), local2(3), local3(4), local4(5), local5(6), local6(7), local7(8) | ||
| agNewCfgSyslogFac | 1.3.6.1.4.1.1872.2.5.1.1.5.6 | ||
| The facility of syslog host in the new_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | local0(1), local1(2), local2(3), local3(4), local4(5), local5(6), local6(7), local7(8) | ||
| agCurCfgSyslog2Fac | 1.3.6.1.4.1.1872.2.5.1.1.5.7 | ||
| The facility of syslog2 host in the current_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | local0(1), local1(2), local2(3), local3(4), local4(5), local5(6), local6(7), local7(8) | ||
| agNewCfgSyslog2Fac | 1.3.6.1.4.1.1872.2.5.1.1.5.8 | ||
| The facility of syslogs host in the new_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | local0(1), local1(2), local2(3), local3(4), local4(5), local5(6), local6(7), local7(8) | ||
| agClrSyslogMsgs | 1.3.6.1.4.1.1872.2.5.1.1.5.9 | ||
| Clears all current Syslog messages. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), reset(2) | ||
| agSyslogMsgTableMaxSize | 1.3.6.1.4.1.1872.2.5.1.1.5.10 | ||
| The maximum number of rows in the syslog message table. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| agSyslogMsgTable | 1.3.6.1.4.1.1872.2.5.1.1.5.11 | ||
| The table of syslog messages. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AgSyslogMsgTableEntry | |||
| agSyslogMsgTableEntry | 1.3.6.1.4.1.1872.2.5.1.1.5.11.1 | ||
| A syslog message stored on the switch. | |||
| OBJECT-TYPE | |||
| AgSyslogMsgTableEntry | |||
| agSyslogMsgIndex | 1.3.6.1.4.1.1872.2.5.1.1.5.11.1.1 | ||
| The syslog message table index. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| agSyslogMessage | 1.3.6.1.4.1.1872.2.5.1.1.5.11.1.2 | ||
| The syslog message. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..128) | ||
| agLog | 1.3.6.1.4.1.1872.2.5.1.1.5.12 | ||
| OBJECT IDENTIFIER | |||
| agNewCfgSyslogTrapConsole | 1.3.6.1.4.1.1872.2.5.1.1.5.12.1 | ||
| Enable or disable console syslog and SNMP trap, in the new_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agCurCfgSyslogTrapConsole | 1.3.6.1.4.1.1872.2.5.1.1.5.12.2 | ||
| Enable or disable console syslog and SNMP trap, as currently configured in the current_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agNewCfgSyslogTrapSystem | 1.3.6.1.4.1.1872.2.5.1.1.5.12.3 | ||
| Enable or disable system level syslog and SNMP trap, in the new_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agCurCfgSyslogTrapSystem | 1.3.6.1.4.1.1872.2.5.1.1.5.12.4 | ||
| Enable or disable system level syslog and SNMP trap, as currently configured in the current_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agNewCfgSyslogTrapMgmt | 1.3.6.1.4.1.1872.2.5.1.1.5.12.5 | ||
| Enable or disable management(flash, config, login) syslog and SNMP trap, in the new_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agCurCfgSyslogTrapMgmt | 1.3.6.1.4.1.1872.2.5.1.1.5.12.6 | ||
| Enable or disable management(flash, config, login) syslog and SNMP trap, as currently configured in the current_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agNewCfgSyslogTrapCli | 1.3.6.1.4.1.1872.2.5.1.1.5.12.7 | ||
| Enable or disable CLI generated error syslog and SNMP trap, in the new_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agCurCfgSyslogTrapCli | 1.3.6.1.4.1.1872.2.5.1.1.5.12.8 | ||
| Enable or disable CLI generated error syslog and SNMP trap, as currently configured in the current_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agNewCfgSyslogTrapStp | 1.3.6.1.4.1.1872.2.5.1.1.5.12.9 | ||
| Enable or disable spanning tree syslog and SNMP trap, in the new_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agCurCfgSyslogTrapStp | 1.3.6.1.4.1.1872.2.5.1.1.5.12.10 | ||
| Enable or disable spanning tree syslog and SNMP trap, as currently configured in the current_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agNewCfgSyslogTrapVlan | 1.3.6.1.4.1.1872.2.5.1.1.5.12.11 | ||
| Enable or disable VLAN syslog and SNMP trap, in the new_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agCurCfgSyslogTrapVlan | 1.3.6.1.4.1.1872.2.5.1.1.5.12.12 | ||
| Enable or disable VLAN syslog and SNMP trap, as currently configured in the current_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agNewCfgSyslogTrapSlb | 1.3.6.1.4.1.1872.2.5.1.1.5.12.13 | ||
| Enable or disable SLB syslog and SNMP trap, in the new_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agCurCfgSyslogTrapSlb | 1.3.6.1.4.1.1872.2.5.1.1.5.12.14 | ||
| Enable or disable SLB syslog and SNMP trap, as currently configured in the current_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agNewCfgSyslogTrapGslb | 1.3.6.1.4.1.1872.2.5.1.1.5.12.15 | ||
| Enable or disable GSLB syslog and SNMP trap, in the new_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agCurCfgSyslogTrapGslb | 1.3.6.1.4.1.1872.2.5.1.1.5.12.16 | ||
| Enable or disable GSLB syslog and SNMP trap, as currently configured in the current_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agNewCfgSyslogTrapFilter | 1.3.6.1.4.1.1872.2.5.1.1.5.12.17 | ||
| Enable or disable filter syslog and SNMP trap, in the new_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agCurCfgSyslogTrapFilter | 1.3.6.1.4.1.1872.2.5.1.1.5.12.18 | ||
| Enable or disable filter syslog and SNMP trap, as currently configured in the current_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agNewCfgSyslogTrapSsh | 1.3.6.1.4.1.1872.2.5.1.1.5.12.19 | ||
| Enable or disable SSH, RADIUS syslog and SNMP trap, in the new_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agCurCfgSyslogTrapSsh | 1.3.6.1.4.1.1872.2.5.1.1.5.12.20 | ||
| Enable or disable SSH, RADIUS syslog and SNMP trap, as currently configured in the current_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agNewCfgSyslogTrapVrrp | 1.3.6.1.4.1.1872.2.5.1.1.5.12.21 | ||
| Enable or disable VRRP syslog and SNMP trap, in the new_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agCurCfgSyslogTrapVrrp | 1.3.6.1.4.1.1872.2.5.1.1.5.12.22 | ||
| Enable or disable VRRP syslog and SNMP trap, as currently configured in the current_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agNewCfgSyslogTrapBgp | 1.3.6.1.4.1.1872.2.5.1.1.5.12.23 | ||
| Enable or disable BGP syslog and SNMP trap, in the new_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agCurCfgSyslogTrapBgp | 1.3.6.1.4.1.1872.2.5.1.1.5.12.24 | ||
| Enable or disable BGP syslog and SNMP trap, as currently configured in the current_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agNewCfgSyslogTrapNtp | 1.3.6.1.4.1.1872.2.5.1.1.5.12.25 | ||
| Enable or disable NTP syslog and SNMP trap, in the new_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agCurCfgSyslogTrapNtp | 1.3.6.1.4.1.1872.2.5.1.1.5.12.26 | ||
| Enable or disable NTP syslog and SNMP trap, as currently configured in the current_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agNewCfgSyslogTrapIp | 1.3.6.1.4.1.1872.2.5.1.1.5.12.31 | ||
| Enable or disable IP related syslog and SNMP trap, in the new_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agCurCfgSyslogTrapIp | 1.3.6.1.4.1.1872.2.5.1.1.5.12.32 | ||
| Enable or disable IP related syslog and SNMP trap, as currently configured in the current_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agNewCfgSyslogTrapWeb | 1.3.6.1.4.1.1872.2.5.1.1.5.12.35 | ||
| Enable or disable WEBUI related syslog and SNMP trap, in the new_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agCurCfgSyslogTrapWeb | 1.3.6.1.4.1.1872.2.5.1.1.5.12.36 | ||
| Enable or disable WEBUI related syslog and SNMP trap, as currently configured in the current_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agNewCfgSyslogTrapSynAtk | 1.3.6.1.4.1.1872.2.5.1.1.5.12.37 | ||
| Enable or disable SYN attack detection related syslog and SNMP trap, in the new_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agCurCfgSyslogTrapSynAtk | 1.3.6.1.4.1.1872.2.5.1.1.5.12.38 | ||
| Enable or disable SYN attack detection related syslog and SNMP trap, as currently configured in the current_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agNewCfgSyslogTrapTcpLim | 1.3.6.1.4.1.1872.2.5.1.1.5.12.39 | ||
| Enable or disable TCP rate limiting related syslog and SNMP trap, in the new_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agCurCfgSyslogTrapTcpLim | 1.3.6.1.4.1.1872.2.5.1.1.5.12.40 | ||
| Enable or disable TCP rate limiting related syslog and SNMP trap, as currently configured in the current_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agNewCfgSyslogTrapOspf | 1.3.6.1.4.1.1872.2.5.1.1.5.12.41 | ||
| Enable or disable OSPF related syslog and SNMP trap, in the new_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agCurCfgSyslogTrapOspf | 1.3.6.1.4.1.1872.2.5.1.1.5.12.42 | ||
| Enable or disable OSPF related syslog and SNMP trap, as currently configured in the current_configuration block. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agTrapHost | 1.3.6.1.4.1.1872.2.5.1.1.6 | ||
| OBJECT IDENTIFIER | |||
| agTrapHostTableMaxEnt | 1.3.6.1.4.1.1872.2.5.1.1.6.1 | ||
| The maximum number of rows in the trap host table. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| agCurCfgTrapHostTable | 1.3.6.1.4.1.1872.2.5.1.1.6.2 | ||
| The table of trap hosts which to send SNMP traps in the current_configuration block. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AgCurCfgTrapHostEntry | |||
| agCurCfgTrapHostEntry | 1.3.6.1.4.1.1872.2.5.1.1.6.2.1 | ||
| A row in the trap host table in the current_configuration block. | |||
| OBJECT-TYPE | |||
| AgCurCfgTrapHostEntry | |||
| agCurCfgTrapHostIndx | 1.3.6.1.4.1.1872.2.5.1.1.6.2.1.1 | ||
| The index of the row in trap host table. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| agCurCfgTrapHostIpAddr | 1.3.6.1.4.1.1872.2.5.1.1.6.2.1.2 | ||
| The IP address of a trap host. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| agCurCfgTrapHostCommString | 1.3.6.1.4.1.1872.2.5.1.1.6.2.1.3 | ||
| The SNMP community string to use with the trap host | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..32) | ||
| agNewCfgTrapHostTable | 1.3.6.1.4.1.1872.2.5.1.1.6.3 | ||
| The table of trap hosts which to send SNMP traps in the new_configuration block. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AgNewCfgTrapHostEntry | |||
| agNewCfgTrapHostEntry | 1.3.6.1.4.1.1872.2.5.1.1.6.3.1 | ||
| A row in the trap host table in the new_configuration block. | |||
| OBJECT-TYPE | |||
| AgNewCfgTrapHostEntry | |||
| agNewCfgTrapHostIndx | 1.3.6.1.4.1.1872.2.5.1.1.6.3.1.1 | ||
| The index of the row in trap host table. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| agNewCfgTrapHostIpAddr | 1.3.6.1.4.1.1872.2.5.1.1.6.3.1.2 | ||
| The IP address of a trap host. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| agNewCfgTrapHostCommString | 1.3.6.1.4.1.1872.2.5.1.1.6.3.1.3 | ||
| The SNMP community string to use with the trap host | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..32) | ||
| agTftp | 1.3.6.1.4.1.1872.2.5.1.1.7 | ||
| OBJECT IDENTIFIER | |||
| agTftpServer | 1.3.6.1.4.1.1872.2.5.1.1.7.1 | ||
| The TFTP server IP address or domain name. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..64) | ||
| agTftpImage | 1.3.6.1.4.1.1872.2.5.1.1.7.2 | ||
| Whether the image file should be loaded in image1 or image2 in flash. | |||
| OBJECT-TYPE | |||
| INTEGER | image1(2), image2(3) | ||
| agTftpImageFileName | 1.3.6.1.4.1.1872.2.5.1.1.7.3 | ||
| The image file name to be downloaded. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..128) | ||
| agTftpCfgFileName | 1.3.6.1.4.1.1872.2.5.1.1.7.4 | ||
| The configuration file name. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..128) | ||
| agTftpDumpFileName | 1.3.6.1.4.1.1872.2.5.1.1.7.5 | ||
| The file name for core dump. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..128) | ||
| agTftpAction | 1.3.6.1.4.1.1872.2.5.1.1.7.6 | ||
| This is an action object to perform various TFTP Get or Put functions. The TFTP sever is specified in agTftpServer object. img-get(2) - Download switch image from a specified image file (agTftpImageFileName) on the TFTP server to the destinated storage (agTftpImage). cfg-get(3) - Download switch configuration from a specified file (agTftpCfgFileName) on the TFTP server. cfg-put(4) - Upload switch configuration to a specified file (agTftpCfgFileName) on the TFTP server. dump-put(5)- Download switch core dump to a specified file (agTftpDumpFileName) on the TFTP server. other(1) is returned always when read. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), img-get(2), cfg-get(3), cfg-put(4), dump-put(5) | ||
| agTftpLastActionStatus | 1.3.6.1.4.1.1872.2.5.1.1.7.7 | ||
| The recorded status of the previous TFTP activity. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..128) | ||
| agTftpPort | 1.3.6.1.4.1.1872.2.5.1.1.7.8 | ||
| Specify whether the TFTP operation should nbe performed over the data port or the management port. | |||
| OBJECT-TYPE | |||
| INTEGER | data(1), mgmt(2) | ||
| agApply | 1.3.6.1.4.1.1872.2.5.1.1.8 | ||
| OBJECT IDENTIFIER | |||
| agApplyPending | 1.3.6.1.4.1.1872.2.5.1.1.8.1 | ||
| This object, when read, gives the user information whether an apply action is needed and that the configuration has been chaged by the user actions. The user then can apply the changes by setting proper value to the object agApplyConfiguration described above. | |||
| OBJECT-TYPE | |||
| INTEGER | applyNeeded(2), noApplyNeeded(3) | ||
| agApplyConfig | 1.3.6.1.4.1.1872.2.5.1.1.8.2 | ||
| When this object is read the current state is returned. idle(3) indicates that there is no apply in progess. complete(5) indicates that the last apply operation is completed. Setting the value to apply(1), will write all the changes made since the last apply to the current configuration block. If the apply is successful this variable will return the state 'complete' else it will return 'failed'. In case of failure, to read the reason for failure use the agApplyTable. Once the operation is completed or the agApplyTable is read in case of failure, the apply buffer needs to be freed and the agApplyState should be set back to 'idle' state so others can issue the apply command via SNMP. | |||
| OBJECT-TYPE | |||
| INTEGER | apply(1), idle(2), inprogress(3), complete(4), failed(5) | ||
| agApplyTableSize | 1.3.6.1.4.1.1872.2.5.1.1.8.4 | ||
| The number of strings in the apply table. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| agApplyTable | 1.3.6.1.4.1.1872.2.5.1.1.8.5 | ||
| The table of URL path for URL load balancing in the current_config. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AgApplyTableEntry | |||
| agApplyTableEntry | 1.3.6.1.4.1.1872.2.5.1.1.8.5.1 | ||
| Information about an URL path for URL load balancing. | |||
| OBJECT-TYPE | |||
| AgApplyTableEntry | |||
| agApplyIndex | 1.3.6.1.4.1.1872.2.5.1.1.8.5.1.1 | ||
| The table index. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| agApplyString | 1.3.6.1.4.1.1872.2.5.1.1.8.5.1.2 | ||
| A string in the apply table. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| agMgmt | 1.3.6.1.4.1.1872.2.5.1.1.9 | ||
| OBJECT IDENTIFIER | |||
| agMgmtCurCfgIpAddr | 1.3.6.1.4.1.1872.2.5.1.1.9.1 | ||
| The IP address of the management port. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| agMgmtNewCfgIpAddr | 1.3.6.1.4.1.1872.2.5.1.1.9.2 | ||
| The IP address of the management port. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| agMgmtCurCfgMask | 1.3.6.1.4.1.1872.2.5.1.1.9.3 | ||
| The subnet mask of the management port. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| agMgmtNewCfgMask | 1.3.6.1.4.1.1872.2.5.1.1.9.4 | ||
| The subnet mask of the management port. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| agMgmtCurCfgBroadcast | 1.3.6.1.4.1.1872.2.5.1.1.9.5 | ||
| The broadcast address of the management port. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| agMgmtNewCfgBroadcast | 1.3.6.1.4.1.1872.2.5.1.1.9.6 | ||
| The broadcast address of the management port. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| agMgmtCurCfgGateway | 1.3.6.1.4.1.1872.2.5.1.1.9.7 | ||
| The default gateway for the management port. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| agMgmtNewCfgGateway | 1.3.6.1.4.1.1872.2.5.1.1.9.8 | ||
| The default gateway for the management port. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| agMgmtCurCfgState | 1.3.6.1.4.1.1872.2.5.1.1.9.9 | ||
| Enable/disable management port. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agMgmtNewCfgState | 1.3.6.1.4.1.1872.2.5.1.1.9.10 | ||
| Enable/disable management port. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agMgmtCurCfgNtp | 1.3.6.1.4.1.1872.2.5.1.1.9.11 | ||
| Specifies NTP access is over management port or data port. | |||
| OBJECT-TYPE | |||
| INTEGER | data(1), mgmt(2) | ||
| agMgmtNewCfgNtp | 1.3.6.1.4.1.1872.2.5.1.1.9.12 | ||
| Specifies NTP access is over management port or data port. | |||
| OBJECT-TYPE | |||
| INTEGER | data(1), mgmt(2) | ||
| agMgmtCurCfgRadius | 1.3.6.1.4.1.1872.2.5.1.1.9.13 | ||
| Specifies RADIUS server access is over management port or data port. | |||
| OBJECT-TYPE | |||
| INTEGER | data(1), mgmt(2) | ||
| agMgmtNewCfgRadius | 1.3.6.1.4.1.1872.2.5.1.1.9.14 | ||
| Specifies RADIUS server access is over management port or data port. | |||
| OBJECT-TYPE | |||
| INTEGER | data(1), mgmt(2) | ||
| agMgmtCurCfgSmtp | 1.3.6.1.4.1.1872.2.5.1.1.9.15 | ||
| Specifies SMTP access is over management port or data port. | |||
| OBJECT-TYPE | |||
| INTEGER | data(1), mgmt(2) | ||
| agMgmtNewCfgSmtp | 1.3.6.1.4.1.1872.2.5.1.1.9.16 | ||
| Specifies SMTP access is over management port or data port. | |||
| OBJECT-TYPE | |||
| INTEGER | data(1), mgmt(2) | ||
| agMgmtCurCfgSnmp | 1.3.6.1.4.1.1872.2.5.1.1.9.17 | ||
| Specifies SNMP trap host access is over management port or data port. | |||
| OBJECT-TYPE | |||
| INTEGER | data(1), mgmt(2) | ||
| agMgmtNewCfgSnmp | 1.3.6.1.4.1.1872.2.5.1.1.9.18 | ||
| Specifies SNMP trap host access is over management port or data port. | |||
| OBJECT-TYPE | |||
| INTEGER | data(1), mgmt(2) | ||
| agMgmtCurCfgSyslog | 1.3.6.1.4.1.1872.2.5.1.1.9.19 | ||
| Specifies syslog host access is over management port or data port. | |||
| OBJECT-TYPE | |||
| INTEGER | data(1), mgmt(2) | ||
| agMgmtNewCfgSyslog | 1.3.6.1.4.1.1872.2.5.1.1.9.20 | ||
| Specifies syslog host access is over management port or data port. | |||
| OBJECT-TYPE | |||
| INTEGER | data(1), mgmt(2) | ||
| agMgmtCurCfgTftp | 1.3.6.1.4.1.1872.2.5.1.1.9.21 | ||
| Specifies TFTP access is over management port or data port. | |||
| OBJECT-TYPE | |||
| INTEGER | data(1), mgmt(2) | ||
| agMgmtNewCfgTftp | 1.3.6.1.4.1.1872.2.5.1.1.9.22 | ||
| Specifies TFTP access is over management port or data port. | |||
| OBJECT-TYPE | |||
| INTEGER | data(1), mgmt(2) | ||
| agMgmtPort | 1.3.6.1.4.1.1872.2.5.1.1.9.23 | ||
| OBJECT IDENTIFIER | |||
| agMgmtPortCurCfgSpeed | 1.3.6.1.4.1.1872.2.5.1.1.9.23.1 | ||
| Set Management port link speed. | |||
| OBJECT-TYPE | |||
| INTEGER | mbs10(1), mbs100(2), any(3) | ||
| agMgmtPortNewCfgSpeed | 1.3.6.1.4.1.1872.2.5.1.1.9.23.2 | ||
| Set Management port link speed. | |||
| OBJECT-TYPE | |||
| INTEGER | mbs10(1), mbs100(2), any(3) | ||
| agMgmtPortCurCfgMode | 1.3.6.1.4.1.1872.2.5.1.1.9.23.3 | ||
| Set Management port full or half duplex mode. | |||
| OBJECT-TYPE | |||
| INTEGER | full(1), half(2), any(3) | ||
| agMgmtPortNewCfgMode | 1.3.6.1.4.1.1872.2.5.1.1.9.23.4 | ||
| Set Management port full or half duplex mode. | |||
| OBJECT-TYPE | |||
| INTEGER | full(1), half(2), any(3) | ||
| agMgmtPortCurCfgAuto | 1.3.6.1.4.1.1872.2.5.1.1.9.23.5 | ||
| Set Management port autonegotiation. | |||
| OBJECT-TYPE | |||
| INTEGER | on(1), off(2) | ||
| agMgmtPortNewCfgAuto | 1.3.6.1.4.1.1872.2.5.1.1.9.23.6 | ||
| Set Management port autonegotiation. | |||
| OBJECT-TYPE | |||
| INTEGER | on(1), off(2) | ||
| agMgmtCurCfgDns | 1.3.6.1.4.1.1872.2.5.1.1.9.24 | ||
| Specifies DNS access is over management port or data port. | |||
| OBJECT-TYPE | |||
| INTEGER | data(1), mgmt(2) | ||
| agMgmtNewCfgDns | 1.3.6.1.4.1.1872.2.5.1.1.9.25 | ||
| Specifies DNS access is over management port or data port. | |||
| OBJECT-TYPE | |||
| INTEGER | data(1), mgmt(2) | ||
| agentStats | 1.3.6.1.4.1.1872.2.5.1.2 | ||
| OBJECT IDENTIFIER | |||
| pktStats | 1.3.6.1.4.1.1872.2.5.1.2.1 | ||
| OBJECT IDENTIFIER | |||
| pktStatsAllocs | 1.3.6.1.4.1.1872.2.5.1.2.1.1 | ||
| Total number of packet allocations from the packet buffer pool by the TCP/IP protocol stack. | |||
| OBJECT-TYPE | |||
| Counter | |||
| pktStatsFrees | 1.3.6.1.4.1.1872.2.5.1.2.1.2 | ||
| Total number of times the packet buffers are freed(released) to the packet buffer pool by the TCP/IP protocol stack. | |||
| OBJECT-TYPE | |||
| Counter | |||
| pktStatsAllocFails | 1.3.6.1.4.1.1872.2.5.1.2.1.3 | ||
| Total number of packet allocation failures from the packet buffer pool by the TCP/IP protocol stack. | |||
| OBJECT-TYPE | |||
| Counter | |||
| pktStatsMediums | 1.3.6.1.4.1.1872.2.5.1.2.1.4 | ||
| Total number of packet allocations with size greater than 128 bytes and less than or equal to 1536 bytes from the packet buffer pool by the TCP/IP protocol stack. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| pktStatsJumbos | 1.3.6.1.4.1.1872.2.5.1.2.1.5 | ||
| Total number of packet allocations with size larger than 1536 bytes from the packet buffer pool by the TCP/IP protocol stack. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| pktStatsSmalls | 1.3.6.1.4.1.1872.2.5.1.2.1.6 | ||
| Total number of packet allocations with size less than or eqaul to 128 bytes from the packet buffer pool by the TCP/IP protocol stack. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| pktStatsMediumsHiWatermark | 1.3.6.1.4.1.1872.2.5.1.2.1.7 | ||
| The highest number of packet allocations with size greater than 128 bytes and less than or equal to 1536 bytes from the packet buffer pool by the TCP/IP protocol stack. | |||
| OBJECT-TYPE | |||
| Counter | |||
| pktStatsJumbosHiWatermark | 1.3.6.1.4.1.1872.2.5.1.2.1.8 | ||
| The highest number of packet allocations with size larger than 1536 bytes from the packet buffer pool by the TCP/IP protocol stack. | |||
| OBJECT-TYPE | |||
| Counter | |||
| pktStatsSmallsHiWatermark | 1.3.6.1.4.1.1872.2.5.1.2.1.9 | ||
| The highest number of packet allocations with size less than or eqaul to 128 bytes from the packet buffer pool by the TCP/IP protocol stack. | |||
| OBJECT-TYPE | |||
| Counter | |||
| pktStatsDiscards | 1.3.6.1.4.1.1872.2.5.1.2.1.10 | ||
| The total number of packets which were chosen to be discarded because the number of buffers available in the packet buffer pool is low. | |||
| OBJECT-TYPE | |||
| Counter | |||
| mpCpuStats | 1.3.6.1.4.1.1872.2.5.1.2.2 | ||
| OBJECT IDENTIFIER | |||
| mpCpuStatsUtil1Second | 1.3.6.1.4.1.1872.2.5.1.2.2.1 | ||
| The utilization of MP CPU over 1 second. It shows the percentage. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| mpCpuStatsUtil4Seconds | 1.3.6.1.4.1.1872.2.5.1.2.2.2 | ||
| The utilization of MP CPU over 4 seconds. It shows the percentage. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| mpCpuStatsUtil64Seconds | 1.3.6.1.4.1.1872.2.5.1.2.2.3 | ||
| The utilization of MP CPU over 64 seconds. It shows the percentage. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| portStats | 1.3.6.1.4.1.1872.2.5.1.2.3 | ||
| OBJECT IDENTIFIER | |||
| portStatsTable | 1.3.6.1.4.1.1872.2.5.1.2.3.1 | ||
| The table of port statistics. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PortStatsTableEntry | |||
| portStatsTableEntry | 1.3.6.1.4.1.1872.2.5.1.2.3.1.1 | ||
| A row in the port stats table. | |||
| OBJECT-TYPE | |||
| PortStatsTableEntry | |||
| portStatsIndx | 1.3.6.1.4.1.1872.2.5.1.2.3.1.1.1 | ||
| The port index. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| portStatsPhyIfInOctets | 1.3.6.1.4.1.1872.2.5.1.2.3.1.1.2 | ||
| The total number of octets received on the interface, including framing characters. | |||
| OBJECT-TYPE | |||
| Counter | |||
| portStatsPhyIfInUcastPkts | 1.3.6.1.4.1.1872.2.5.1.2.3.1.1.3 | ||
| The number of subnetwork-unicast packets delivered to a higher-layer protocol. | |||
| OBJECT-TYPE | |||
| Counter | |||
| portStatsPhyIfInNUcastPkts | 1.3.6.1.4.1.1872.2.5.1.2.3.1.1.4 | ||
| The number of non-unicast (i.e., subnetwork- broadcast or subnetwork-multicast) packets delivered to a higher-layer protocol. | |||
| OBJECT-TYPE | |||
| Counter | |||
| portStatsPhyIfInDiscards | 1.3.6.1.4.1.1872.2.5.1.2.3.1.1.5 | ||
| The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space. | |||
| OBJECT-TYPE | |||
| Counter | |||
| portStatsPhyIfInErrors | 1.3.6.1.4.1.1872.2.5.1.2.3.1.1.6 | ||
| The number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. | |||
| OBJECT-TYPE | |||
| Counter | |||
| portStatsPhyIfInUnknownProtos | 1.3.6.1.4.1.1872.2.5.1.2.3.1.1.7 | ||
| The number of packets received via the interface which were discarded because of an unknown or unsupported protocol. | |||
| OBJECT-TYPE | |||
| Counter | |||
| portStatsPhyIfOutOctets | 1.3.6.1.4.1.1872.2.5.1.2.3.1.1.8 | ||
| The total number of octets transmitted out of the interface, including framing characters. | |||
| OBJECT-TYPE | |||
| Counter | |||
| portStatsPhyIfOutUcastPkts | 1.3.6.1.4.1.1872.2.5.1.2.3.1.1.9 | ||
| The total number of packets that higher-level protocols requested be transmitted to a subnetwork-unicast address, including those that were discarded or not sent. | |||
| OBJECT-TYPE | |||
| Counter | |||
| portStatsPhyIfOutNUcastPkts | 1.3.6.1.4.1.1872.2.5.1.2.3.1.1.10 | ||
| The total number of packets that higher-level protocols requested be transmitted to a non- unicast (i.e., a subnetwork-broadcast or subnetwork-multicast) address, including those that were discarded or not sent. | |||
| OBJECT-TYPE | |||
| Counter | |||
| portStatsPhyIfOutDiscards | 1.3.6.1.4.1.1872.2.5.1.2.3.1.1.11 | ||
| The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space. | |||
| OBJECT-TYPE | |||
| Counter | |||
| portStatsPhyIfOutErrors | 1.3.6.1.4.1.1872.2.5.1.2.3.1.1.12 | ||
| The number of outbound packets that could not be transmitted because of errors. | |||
| OBJECT-TYPE | |||
| Counter | |||
| portStatsPhyIfOutQLen | 1.3.6.1.4.1.1872.2.5.1.2.3.1.1.13 | ||
| The length of the output packet queue (in packets). | |||
| OBJECT-TYPE | |||
| Gauge | |||
| portStatsPhyIfInBroadcastPkts | 1.3.6.1.4.1.1872.2.5.1.2.3.1.1.14 | ||
| The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer. | |||
| OBJECT-TYPE | |||
| Counter | |||
| portStatsPhyIfOutBroadcastPkts | 1.3.6.1.4.1.1872.2.5.1.2.3.1.1.15 | ||
| The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a broadcast address at this sub-layer, including those that were discarded or not sent. | |||
| OBJECT-TYPE | |||
| Counter | |||
| portStatsClear | 1.3.6.1.4.1.1872.2.5.1.2.3.1.1.16 | ||
| Setting this value to clear(2) clears the stats for this port. | |||
| OBJECT-TYPE | |||
| INTEGER | ok(1), clear(2) | ||
| spStats | 1.3.6.1.4.1.1872.2.5.1.2.4 | ||
| OBJECT IDENTIFIER | |||
| spStatsCpuUtilTable | 1.3.6.1.4.1.1872.2.5.1.2.4.1 | ||
| The table of SP CPU utilization. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SpStatsCpuUtilTableEntry | |||
| spStatsCpuUtilTableEntry | 1.3.6.1.4.1.1872.2.5.1.2.4.1.1 | ||
| A row in the SP CPU utilization table. | |||
| OBJECT-TYPE | |||
| SpStatsCpuUtilTableEntry | |||
| spStatsCpuUtilSpIndex | 1.3.6.1.4.1.1872.2.5.1.2.4.1.1.1 | ||
| The SP index. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| spStatsCpuUtil1Second | 1.3.6.1.4.1.1872.2.5.1.2.4.1.1.2 | ||
| The utilization of this SP over 1 second. It shows the percentage. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| spStatsCpuUtil4Seconds | 1.3.6.1.4.1.1872.2.5.1.2.4.1.1.3 | ||
| The utilization of this SP over 4 seconds. It shows the percentage. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| spStatsCpuUtil64Seconds | 1.3.6.1.4.1.1872.2.5.1.2.4.1.1.4 | ||
| The utilization of this SP over 64 seconds. It shows the percentage. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| spMaintStatsTable | 1.3.6.1.4.1.1872.2.5.1.2.4.2 | ||
| The table of SP maintenance statistics. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SpMaintStatsTableEntry | |||
| spMaintStatsTableEntry | 1.3.6.1.4.1.1872.2.5.1.2.4.2.1 | ||
| A row in the SP maintenance statistics table. | |||
| OBJECT-TYPE | |||
| SpMaintStatsTableEntry | |||
| spMaintStatsSpIndex | 1.3.6.1.4.1.1872.2.5.1.2.4.2.1.1 | ||
| The SP index. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| spMaintStatsPfdbFreeEmpty | 1.3.6.1.4.1.1872.2.5.1.2.4.2.1.2 | ||
| The number of times the attempts were made to add entries to an already full FDB. | |||
| OBJECT-TYPE | |||
| Counter | |||
| spMaintStatsResolveErrNoddw | 1.3.6.1.4.1.1872.2.5.1.2.4.2.1.3 | ||
| The number of times MAC address resolution failed because there were no DMA descriptors. | |||
| OBJECT-TYPE | |||
| Counter | |||
| spMaintStatsLearnErrNoddw | 1.3.6.1.4.1.1872.2.5.1.2.4.2.1.4 | ||
| The number of times MAC address learn failed because there were no DMA descriptors. | |||
| OBJECT-TYPE | |||
| Counter | |||
| spMaintStatsAgeMPNoddw | 1.3.6.1.4.1.1872.2.5.1.2.4.2.1.5 | ||
| The number of times MAC address aging failed because there were no DMA descriptors. | |||
| OBJECT-TYPE | |||
| Counter | |||
| spMaintStatsDeleteMiss | 1.3.6.1.4.1.1872.2.5.1.2.4.2.1.6 | ||
| The number of times MAC address could not be found. | |||
| OBJECT-TYPE | |||
| Counter | |||
| spMaintStatsRecvLetErrorsMP | 1.3.6.1.4.1.1872.2.5.1.2.4.2.1.7 | ||
| The number of receive letter errors from MP. | |||
| OBJECT-TYPE | |||
| Counter | |||
| spMaintStatsRecvLetErrorsSP1 | 1.3.6.1.4.1.1872.2.5.1.2.4.2.1.8 | ||
| The number of receive letter errors from SP1. If the current table index is the same as the SP number then a value of 0 is returned. | |||
| OBJECT-TYPE | |||
| Counter | |||
| spMaintStatsRecvLetErrorsSP2 | 1.3.6.1.4.1.1872.2.5.1.2.4.2.1.9 | ||
| The number of receive letter errors from SP2. If the current table index is the same as the SP number then a value of 0 is returned. | |||
| OBJECT-TYPE | |||
| Counter | |||
| spMaintStatsRecvLetErrorsSP3 | 1.3.6.1.4.1.1872.2.5.1.2.4.2.1.10 | ||
| The number of receive letter errors from SP3. If the current table index is the same as the SP number then a value of 0 is returned. | |||
| OBJECT-TYPE | |||
| Counter | |||
| spMaintStatsRecvLetErrorsSP4 | 1.3.6.1.4.1.1872.2.5.1.2.4.2.1.11 | ||
| The number of receive letter errors from SP4. If the current table index is the same as the SP number then a value of 0 is returned. | |||
| OBJECT-TYPE | |||
| Counter | |||
| spMaintStatsSendLetFailsMP | 1.3.6.1.4.1.1872.2.5.1.2.4.2.1.12 | ||
| The number of send letter failures to MP. | |||
| OBJECT-TYPE | |||
| Counter | |||
| spMaintStatsSendLetFailsSP1 | 1.3.6.1.4.1.1872.2.5.1.2.4.2.1.13 | ||
| The number of send letter failures to SP1. If the current table index is the same as the SP number then a value of 0 is returned. | |||
| OBJECT-TYPE | |||
| Counter | |||
| spMaintStatsSendLetFailsSP2 | 1.3.6.1.4.1.1872.2.5.1.2.4.2.1.14 | ||
| The number of send letter failures to SP2. If the current table index is the same as the SP number then a value of 0 is returned. | |||
| OBJECT-TYPE | |||
| Counter | |||
| spMaintStatsSendLetFailsSP3 | 1.3.6.1.4.1.1872.2.5.1.2.4.2.1.15 | ||
| The number of send letter failures to SP3. If the current table index is the same as the SP number then a value of 0 is returned. | |||
| OBJECT-TYPE | |||
| Counter | |||
| spMaintStatsSendLetFailsSP4 | 1.3.6.1.4.1.1872.2.5.1.2.4.2.1.16 | ||
| The number of send letter failures to SP4. If the current table index is the same as the SP number then a value of 0 is returned. | |||
| OBJECT-TYPE | |||
| Counter | |||
| spMaintStatsRecvLetSuccessMP | 1.3.6.1.4.1.1872.2.5.1.2.4.2.1.17 | ||
| The number of receive letter success from MP. | |||
| OBJECT-TYPE | |||
| Counter | |||
| spMaintStatsRecvLetSuccessSP1 | 1.3.6.1.4.1.1872.2.5.1.2.4.2.1.18 | ||
| The number of receive letter success from SP1. If the current table index is the same as the SP number then a value of 0 is returned. | |||
| OBJECT-TYPE | |||
| Counter | |||
| spMaintStatsRecvLetSuccessSP2 | 1.3.6.1.4.1.1872.2.5.1.2.4.2.1.19 | ||
| The number of receive letter success from SP2. If the current table index is the same as the SP number then a value of 0 is returned. | |||
| OBJECT-TYPE | |||
| Counter | |||
| spMaintStatsRecvLetSuccessSP3 | 1.3.6.1.4.1.1872.2.5.1.2.4.2.1.20 | ||
| The number of receive letter success from SP3. If the current table index is the same as the SP number then a value of 0 is returned. | |||
| OBJECT-TYPE | |||
| Counter | |||
| spMaintStatsRecvLetSuccessSP4 | 1.3.6.1.4.1.1872.2.5.1.2.4.2.1.21 | ||
| The number of receive letter success from SP4. If the current table index is the same as the SP number then a value of 0 is returned. | |||
| OBJECT-TYPE | |||
| Counter | |||
| spMaintStatsSendLetSuccessMP | 1.3.6.1.4.1.1872.2.5.1.2.4.2.1.22 | ||
| The number of send letter success to MP. | |||
| OBJECT-TYPE | |||
| Counter | |||
| spMaintStatsSendLetSuccessSP1 | 1.3.6.1.4.1.1872.2.5.1.2.4.2.1.23 | ||
| The number of send letter success to SP1. If the current table index is the same as the SP number then a value of 0 is returned. | |||
| OBJECT-TYPE | |||
| Counter | |||
| spMaintStatsSendLetSuccessSP2 | 1.3.6.1.4.1.1872.2.5.1.2.4.2.1.24 | ||
| The number of send letter success to SP2. If the current table index is the same as the SP number then a value of 0 is returned. | |||
| OBJECT-TYPE | |||
| Counter | |||
| spMaintStatsSendLetSuccessSP3 | 1.3.6.1.4.1.1872.2.5.1.2.4.2.1.25 | ||
| The number of send letter success to SP3. If the current table index is the same as the SP number then a value of 0 is returned. | |||
| OBJECT-TYPE | |||
| Counter | |||
| spMaintStatsSendLetSuccessSP4 | 1.3.6.1.4.1.1872.2.5.1.2.4.2.1.26 | ||
| The number of send letter success to SP4. If the current table index is the same as the SP number then a value of 0 is returned. | |||
| OBJECT-TYPE | |||
| Counter | |||
| mgmtStats | 1.3.6.1.4.1.1872.2.5.1.2.5 | ||
| OBJECT IDENTIFIER | |||
| mgmtStatsRxpackets | 1.3.6.1.4.1.1872.2.5.1.2.5.1 | ||
| Total number of packet allocations from the packet buffer pool by the TCP/IP protocol stack. | |||
| OBJECT-TYPE | |||
| Counter | |||
| mgmtStatsRxErrors | 1.3.6.1.4.1.1872.2.5.1.2.5.2 | ||
| The number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. | |||
| OBJECT-TYPE | |||
| Counter | |||
| mgmtStatsRxDropped | 1.3.6.1.4.1.1872.2.5.1.2.5.3 | ||
| The number of inbound packets that were dropped. | |||
| OBJECT-TYPE | |||
| Counter | |||
| mgmtStatsRxOverruns | 1.3.6.1.4.1.1872.2.5.1.2.5.4 | ||
| The number of data overruns over this link. | |||
| OBJECT-TYPE | |||
| Counter | |||
| mgmtStatsRxFrame | 1.3.6.1.4.1.1872.2.5.1.2.5.5 | ||
| The number of frames received on this link. | |||
| OBJECT-TYPE | |||
| Counter | |||
| mgmtStatsTxpackets | 1.3.6.1.4.1.1872.2.5.1.2.5.6 | ||
| Total number of packet allocations from the packet buffer pool by the TCP/IP protocol stack. | |||
| OBJECT-TYPE | |||
| Counter | |||
| mgmtStatsTxErrors | 1.3.6.1.4.1.1872.2.5.1.2.5.7 | ||
| The number of outbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. | |||
| OBJECT-TYPE | |||
| Counter | |||
| mgmtStatsTxDropped | 1.3.6.1.4.1.1872.2.5.1.2.5.8 | ||
| The number of outbound packets that were dropped. | |||
| OBJECT-TYPE | |||
| Counter | |||
| mgmtStatsTxOverruns | 1.3.6.1.4.1.1872.2.5.1.2.5.9 | ||
| The number of data overruns over this link. | |||
| OBJECT-TYPE | |||
| Counter | |||
| mgmtStatsTxCarrier | 1.3.6.1.4.1.1872.2.5.1.2.5.10 | ||
| The number of times that the carrier sense condition was lost or never asserted when attempting to transmit a frame on a this interface. | |||
| OBJECT-TYPE | |||
| Counter | |||
| mgmtStatsTxCollisions | 1.3.6.1.4.1.1872.2.5.1.2.5.11 | ||
| The number of collisions on this outbound segment. | |||
| OBJECT-TYPE | |||
| Counter | |||
| mgmtStatsTxQueueLen | 1.3.6.1.4.1.1872.2.5.1.2.5.12 | ||
| The length of the TCP transmit queue. | |||
| OBJECT-TYPE | |||
| Counter | |||
| agentInfo | 1.3.6.1.4.1.1872.2.5.1.3 | ||
| OBJECT IDENTIFIER | |||
| hardware | 1.3.6.1.4.1.1872.2.5.1.3.1 | ||
| OBJECT IDENTIFIER | |||
| hwPartNumber | 1.3.6.1.4.1.1872.2.5.1.3.1.1 | ||
| The hardware part number of the Alteon Switch. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..16) | ||
| hwRevision | 1.3.6.1.4.1.1872.2.5.1.3.1.2 | ||
| The hardware revision. If the revision is not available, a zero length string should be returned. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..16) | ||
| hwTemperatureStatus | 1.3.6.1.4.1.1872.2.5.1.3.1.3 | ||
| The status of the temperature sensor. | |||
| OBJECT-TYPE | |||
| INTEGER | ok(1), exceed(2) | ||
| hwFanStatus | 1.3.6.1.4.1.1872.2.5.1.3.1.4 | ||
| The status of the fan. | |||
| OBJECT-TYPE | |||
| INTEGER | ok(1), fail(2) | ||
| portInfo | 1.3.6.1.4.1.1872.2.5.1.3.2 | ||
| OBJECT IDENTIFIER | |||
| portInfoTable | 1.3.6.1.4.1.1872.2.5.1.3.2.1 | ||
| The table of port information. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PortInfoTableEntry | |||
| portInfoTableEntry | 1.3.6.1.4.1.1872.2.5.1.3.2.1.1 | ||
| A row in the port information table. | |||
| OBJECT-TYPE | |||
| PortInfoTableEntry | |||
| portInfoIndx | 1.3.6.1.4.1.1872.2.5.1.3.2.1.1.1 | ||
| The port index. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| portInfoSpeed | 1.3.6.1.4.1.1872.2.5.1.3.2.1.1.2 | ||
| The current operational speed of the port. | |||
| OBJECT-TYPE | |||
| INTEGER | mbs10(2), mbs100(3), mbs1000(4), any(5) | ||
| portInfoMode | 1.3.6.1.4.1.1872.2.5.1.3.2.1.1.3 | ||
| The current operational mode of the port. | |||
| OBJECT-TYPE | |||
| INTEGER | full-duplex(2), half-duplex(3) | ||
| portInfoFlowCtrl | 1.3.6.1.4.1.1872.2.5.1.3.2.1.1.4 | ||
| The current operational flow control of the port. | |||
| OBJECT-TYPE | |||
| INTEGER | transmit(2), receive(3), both(4), none(5) | ||
| portInfoLink | 1.3.6.1.4.1.1872.2.5.1.3.2.1.1.5 | ||
| The current operational link status of the port. | |||
| OBJECT-TYPE | |||
| INTEGER | up(1), down(2), disabled(3), inoperative(4) | ||
| portInfoPhyIfDescr | 1.3.6.1.4.1.1872.2.5.1.3.2.1.1.6 | ||
| A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the hardware interface. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| portInfoPhyIfType | 1.3.6.1.4.1.1872.2.5.1.3.2.1.1.7 | ||
| The type of interface, distinguished according to the physical/link protocol(s) immediately `below' the network layer in the protocol stack. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), regular1822(2), hdh1822(3), ddn-x25(4), rfc877-x25(5), ethernet-csmacd(6), iso88023-csmacd(7), iso88024-tokenBus(8), iso88025-tokenRing(9), iso88026-man(10), starLan(11), proteon-10Mbit(12), proteon-80Mbit(13), hyperchannel(14), fddi(15), lapb(16), sdlc(17), ds1(18), e1(19), basicISDN(20), primaryISDN(21), propPointToPointSerial(22), ppp(23), softwareLoopback(24), eon(25), ethernet-3Mbit(26), nsip(27), slip(28), ultra(29), ds3(30), sip(31), frame-relay(32) | ||
| portInfoPhyIfMtu | 1.3.6.1.4.1.1872.2.5.1.3.2.1.1.8 | ||
| The size of the largest datagram which can be sent/received on the interface, specified in octets. For interfaces that are used for transmitting network datagrams, this is the size of the largest network datagram that can be sent on the interface. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| portInfoPhyIfPhysAddress | 1.3.6.1.4.1.1872.2.5.1.3.2.1.1.9 | ||
| The interface's address at the protocol layer immediately `below' the network layer in the protocol stack. For interfaces which do not have such an address (e.g., a serial line), this object should contain an octet string of zero length. | |||
| OBJECT-TYPE | |||
| PhysAddress | |||
| portInfoPhyIfOperStatus | 1.3.6.1.4.1.1872.2.5.1.3.2.1.1.10 | ||
| The current operational state of the interface. The testing(3) state indicates that no operational packets can be passed. | |||
| OBJECT-TYPE | |||
| INTEGER | up(1), down(2), testing(3) | ||
| portInfoPhyIfLastChange | 1.3.6.1.4.1.1872.2.5.1.3.2.1.1.11 | ||
| The value of sysUpTime at the time the interface entered its current operational state. If the current state was entered prior to the last re- initialization of the local network management subsystem, then this object contains a zero value. | |||
| OBJECT-TYPE | |||
| TimeTicks | |||
| swKeyInfo | 1.3.6.1.4.1.1872.2.5.1.3.3 | ||
| OBJECT IDENTIFIER | |||
| agEnabledSwFeatures | 1.3.6.1.4.1.1872.2.5.1.3.3.1 | ||
| The software features that are enabled on the switch. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| agEnabledGslbKey | 1.3.6.1.4.1.1872.2.5.1.3.3.2 | ||
| Query if software key Global slb enabled on switch. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agEnabledBwmKey | 1.3.6.1.4.1.1872.2.5.1.3.3.3 | ||
| Query if software key Bandwidth Mgmt. enabled on switch. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| agDiff | 1.3.6.1.4.1.1872.2.5.1.3.4 | ||
| OBJECT IDENTIFIER | |||
| agDiffState | 1.3.6.1.4.1.1872.2.5.1.3.4.2 | ||
| When this object is read the current state is returned. idle(3) indicates that there is no diff in progess. complete(5) indicates that the last diff operation is completed. Setting the value to diff(1), will start a new diff operation Diff compares the new configuration with the current configuration and shows the pending configuration changes. Setting the value to flashdiff(1), will start a new diff operation. flashdiff compares new configuration with the flash configuration. To read the configuration changes use the agDiffTable once the state of this variable returns complete. Once the agDiffTable is read the state should be set back to 'idle' which frees the diff buffer and others can issue a diff command via SNMP. | |||
| OBJECT-TYPE | |||
| INTEGER | diff(1), flashdiff(2), idle(3), inprogress(4), complete(5) | ||
| agDiffTableSize | 1.3.6.1.4.1.1872.2.5.1.3.4.3 | ||
| The number of strings in the diff table. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| agDiffTable | 1.3.6.1.4.1.1872.2.5.1.3.4.4 | ||
| The table of diff strings. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AgDiffTableEntry | |||
| agDiffTableEntry | 1.3.6.1.4.1.1872.2.5.1.3.4.4.1 | ||
| An entry in the diff table. | |||
| OBJECT-TYPE | |||
| AgDiffTableEntry | |||
| agDiffIndex | 1.3.6.1.4.1.1872.2.5.1.3.4.4.1.1 | ||
| The table index. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| agDiffString | 1.3.6.1.4.1.1872.2.5.1.3.4.4.1.2 | ||
| A string in the diff table. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| agCfgDump | 1.3.6.1.4.1.1872.2.5.1.3.5 | ||
| OBJECT IDENTIFIER | |||
| agCfgDumpState | 1.3.6.1.4.1.1872.2.5.1.3.5.2 | ||
| When this object is read the current state is returned. idle(2) indicates that there is no dump in progess. complete(4) indicates that the last dump operation is completed. Setting the value to dump(1), will start a new dump operation Dump will show the current configuration. To read the configuration dump use the agCfgDumpTable once the state of this variable returns complete. Once the agCfgDumpTable is read the state should be set back to 'idle' which frees the dump buffer and others can issue a dump command via SNMP. | |||
| OBJECT-TYPE | |||
| INTEGER | dump(1), idle(2), inprogress(3), complete(4) | ||
| agCfgDumpTableSize | 1.3.6.1.4.1.1872.2.5.1.3.5.3 | ||
| The number of strings in the dump table. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| agCfgDumpTable | 1.3.6.1.4.1.1872.2.5.1.3.5.4 | ||
| The table of dump strings. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AgCfgDumpTableEntry | |||
| agCfgDumpTableEntry | 1.3.6.1.4.1.1872.2.5.1.3.5.4.1 | ||
| An entry in the dump table. | |||
| OBJECT-TYPE | |||
| AgCfgDumpTableEntry | |||
| agCfgDumpIndex | 1.3.6.1.4.1.1872.2.5.1.3.5.4.1.1 | ||
| The table index. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| agCfgDumpString | 1.3.6.1.4.1.1872.2.5.1.3.5.4.1.2 | ||
| A string in the dump table. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| mgmtInfo | 1.3.6.1.4.1.1872.2.5.1.3.6 | ||
| OBJECT IDENTIFIER | |||
| mgmtPortInfoSpeed | 1.3.6.1.4.1.1872.2.5.1.3.6.1 | ||
| The current operational speed of the management port. | |||
| OBJECT-TYPE | |||
| INTEGER | mbs10(1), mbs100(2), any(3) | ||
| mgmtPortInfoMode | 1.3.6.1.4.1.1872.2.5.1.3.6.2 | ||
| The current operational mode of the management port. | |||
| OBJECT-TYPE | |||
| INTEGER | full-duplex(1), half-duplex(2), any(3) | ||
| mgmtPortInfoLink | 1.3.6.1.4.1.1872.2.5.1.3.6.3 | ||
| The current operational link status of the management port. | |||
| OBJECT-TYPE | |||
| INTEGER | up(1), down(2), disabled(3) | ||
| agentOper | 1.3.6.1.4.1.1872.2.5.1.4 | ||
| OBJECT IDENTIFIER | |||
| agPortOperTable | 1.3.6.1.4.1.1872.2.5.1.4.1 | ||
| The table of port operations. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AgPortOperTableEntry | |||
| agPortOperTableEntry | 1.3.6.1.4.1.1872.2.5.1.4.1.1 | ||
| A row in the port operations table. | |||
| OBJECT-TYPE | |||
| AgPortOperTableEntry | |||
| portOperIdx | 1.3.6.1.4.1.1872.2.5.1.4.1.1.1 | ||
| The port index. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| portOperState | 1.3.6.1.4.1.1872.2.5.1.4.1.1.2 | ||
| Enable/Disable port. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| portOperRmon | 1.3.6.1.4.1.1872.2.5.1.4.1.1.3 | ||
| Enable/Disable RMON for port. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| AgPortOperTableEntry | |||
| SEQUENCE | |||
| INTEGER as portOperIdx | |||
| INTEGER as portOperState | |||
| INTEGER as portOperRmon | |||
| PortInfoTableEntry | |||
| SEQUENCE | |||
| INTEGER as portInfoIndx | |||
| INTEGER as portInfoSpeed | |||
| INTEGER as portInfoMode | |||
| INTEGER as portInfoFlowCtrl | |||
| INTEGER as portInfoLink | |||
| DisplayString as portInfoPhyIfDescr | |||
| INTEGER as portInfoPhyIfType | |||
| INTEGER as portInfoPhyIfMtu | |||
| PhysAddress as portInfoPhyIfPhysAddress | |||
| INTEGER as portInfoPhyIfOperStatus | |||
| TimeTicks as portInfoPhyIfLastChange | |||
| AgSyslogMsgTableEntry | |||
| SEQUENCE | |||
| INTEGER as agSyslogMsgIndex | |||
| DisplayString as agSyslogMessage | |||
| AgCurCfgTrapHostEntry | |||
| SEQUENCE | |||
| INTEGER as agCurCfgTrapHostIndx | |||
| IpAddress as agCurCfgTrapHostIpAddr | |||
| DisplayString as agCurCfgTrapHostCommString | |||
| AgNewCfgTrapHostEntry | |||
| SEQUENCE | |||
| INTEGER as agNewCfgTrapHostIndx | |||
| IpAddress as agNewCfgTrapHostIpAddr | |||
| DisplayString as agNewCfgTrapHostCommString | |||
| AgPortCurCfgTableEntry | |||
| SEQUENCE | |||
| INTEGER as agPortCurCfgIndx | |||
| INTEGER as agPortCurCfgState | |||
| INTEGER as agPortCurCfgVlanTag | |||
| INTEGER as agPortCurCfgStp | |||
| INTEGER as agPortCurCfgRmon | |||
| INTEGER as agPortCurCfgPVID | |||
| INTEGER as agPortCurCfgFastEthAutoNeg | |||
| INTEGER as agPortCurCfgFastEthSpeed | |||
| INTEGER as agPortCurCfgFastEthMode | |||
| INTEGER as agPortCurCfgFastEthFctl | |||
| INTEGER as agPortCurCfgGigEthAutoNeg | |||
| INTEGER as agPortCurCfgGigEthFctl | |||
| DisplayString as agPortCurCfgPortName | |||
| INTEGER as agPortCurCfgBwmContract | |||
| INTEGER as agPortCurCfgDiscardNonIPs | |||
| INTEGER as agPortCurCfgLinkTrap | |||
| AgPortNewCfgTableEntry | |||
| SEQUENCE | |||
| INTEGER as agPortNewCfgIndx | |||
| INTEGER as agPortNewCfgState | |||
| INTEGER as agPortNewCfgVlanTag | |||
| INTEGER as agPortNewCfgStp | |||
| INTEGER as agPortNewCfgRmon | |||
| INTEGER as agPortNewCfgPVID | |||
| INTEGER as agPortNewCfgFastEthAutoNeg | |||
| INTEGER as agPortNewCfgFastEthSpeed | |||
| INTEGER as agPortNewCfgFastEthMode | |||
| INTEGER as agPortNewCfgFastEthFctl | |||
| INTEGER as agPortNewCfgGigEthAutoNeg | |||
| INTEGER as agPortNewCfgGigEthFctl | |||
| DisplayString as agPortNewCfgPortName | |||
| INTEGER as agPortNewCfgBwmContract | |||
| INTEGER as agPortNewCfgDiscardNonIPs | |||
| INTEGER as agPortNewCfgLinkTrap | |||
| AgApplyTableEntry | |||
| SEQUENCE | |||
| INTEGER as agApplyIndex | |||
| OCTET STRING as agApplyString | |||
| PortStatsTableEntry | |||
| SEQUENCE | |||
| INTEGER as portStatsIndx | |||
| Counter as portStatsPhyIfInOctets | |||
| Counter as portStatsPhyIfInUcastPkts | |||
| Counter as portStatsPhyIfInNUcastPkts | |||
| Counter as portStatsPhyIfInDiscards | |||
| Counter as portStatsPhyIfInErrors | |||
| Counter as portStatsPhyIfInUnknownProtos | |||
| Counter as portStatsPhyIfOutOctets | |||
| Counter as portStatsPhyIfOutUcastPkts | |||
| Counter as portStatsPhyIfOutNUcastPkts | |||
| Counter as portStatsPhyIfOutDiscards | |||
| Counter as portStatsPhyIfOutErrors | |||
| Gauge as portStatsPhyIfOutQLen | |||
| Counter as portStatsPhyIfInBroadcastPkts | |||
| Counter as portStatsPhyIfOutBroadcastPkts | |||
| INTEGER as portStatsClear | |||
| AgDiffTableEntry | |||
| SEQUENCE | |||
| INTEGER as agDiffIndex | |||
| OCTET STRING as agDiffString | |||
| AgCfgDumpTableEntry | |||
| SEQUENCE | |||
| INTEGER as agCfgDumpIndex | |||
| OCTET STRING as agCfgDumpString | |||
| SpStatsCpuUtilTableEntry | |||
| SEQUENCE | |||
| INTEGER as spStatsCpuUtilSpIndex | |||
| INTEGER as spStatsCpuUtil1Second | |||
| INTEGER as spStatsCpuUtil4Seconds | |||
| INTEGER as spStatsCpuUtil64Seconds | |||
| SpMaintStatsTableEntry | |||
| SEQUENCE | |||
| INTEGER as spMaintStatsSpIndex | |||
| Counter as spMaintStatsPfdbFreeEmpty | |||
| Counter as spMaintStatsResolveErrNoddw | |||
| Counter as spMaintStatsLearnErrNoddw | |||
| Counter as spMaintStatsAgeMPNoddw | |||
| Counter as spMaintStatsDeleteMiss | |||
| Counter as spMaintStatsRecvLetErrorsMP | |||
| Counter as spMaintStatsRecvLetErrorsSP1 | |||
| Counter as spMaintStatsRecvLetErrorsSP2 | |||
| Counter as spMaintStatsRecvLetErrorsSP3 | |||
| Counter as spMaintStatsRecvLetErrorsSP4 | |||
| Counter as spMaintStatsSendLetFailsMP | |||
| Counter as spMaintStatsSendLetFailsSP1 | |||
| Counter as spMaintStatsSendLetFailsSP2 | |||
| Counter as spMaintStatsSendLetFailsSP3 | |||
| Counter as spMaintStatsSendLetFailsSP4 | |||
| Counter as spMaintStatsRecvLetSuccessMP | |||
| Counter as spMaintStatsRecvLetSuccessSP1 | |||
| Counter as spMaintStatsRecvLetSuccessSP2 | |||
| Counter as spMaintStatsRecvLetSuccessSP3 | |||
| Counter as spMaintStatsRecvLetSuccessSP4 | |||
| Counter as spMaintStatsSendLetSuccessMP | |||
| Counter as spMaintStatsSendLetSuccessSP1 | |||
| Counter as spMaintStatsSendLetSuccessSP2 | |||
| Counter as spMaintStatsSendLetSuccessSP3 | |||
| Counter as spMaintStatsSendLetSuccessSP4 | |||