
ALTEON-TIGON-SWITCH-MIB
File:
ALTEON-TIGON-SWITCH-MIB.mib (49797 bytes)
Imported modules
Imported symbols
Defined Objects
| hardware |
1.3.6.1.4.1.1872.2.1.1 |
| OBJECT IDENTIFIER |
|
|
|
| hwRevision |
1.3.6.1.4.1.1872.2.1.1.2 |
| The hardware revision. If the revision is not available, a zero length string should be returned. |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
SIZE(0..16) |
|
| hwSensor2Temp |
1.3.6.1.4.1.1872.2.1.1.7 |
| The temperature of the rear middle sensor in degrees Celsius. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| hwSensor3Temp |
1.3.6.1.4.1.1872.2.1.1.8 |
| The temperature of the front middle sensor in degrees Celsius. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| hwSensor4Temp |
1.3.6.1.4.1.1872.2.1.1.9 |
| The temperature of the front right sensor in degrees Celsius. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| agent |
1.3.6.1.4.1.1872.2.1.2 |
| OBJECT IDENTIFIER |
|
|
|
| agGeneral |
1.3.6.1.4.1.1872.2.1.2.1 |
| OBJECT IDENTIFIER |
|
|
|
| agSaveConfiguration |
1.3.6.1.4.1.1872.2.1.2.1.1 |
| This is an action object to write current configuration to nonvolatile storage. When issued with the saveActive, the active configuration in flash is saved to backup in flash and then the new configuration is saved to the active configuration in flash. When issued with notSaveActive, the active configuration is NOT saved to the flash and the active configuration is overwritten with the new configuration. ok(1) is returned always when read. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
ok(1), saveActive(2), notSaveActive(3) |
|
| agApplyConfiguration |
1.3.6.1.4.1.1872.2.1.2.1.2 |
| This is an action object to apply the changes made to configuration of the switch. By setting the value to apply(2), all the changes made since the last apply are written to the new_config block. other(1) is returned when this object ie read. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
other(1), apply(2) |
|
| agApplyPending |
1.3.6.1.4.1.1872.2.1.2.1.3 |
| This object, when read, gives the user information whether an apply action is needed and that the configuration has been chaged by the user actions. The user then can apply the changes by setting proper value to the object agApplyConfiguration described above. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
applyNeeded(2), noApplyNeeded(3) |
|
| agReset |
1.3.6.1.4.1.1872.2.1.2.1.4 |
| This is an action object to reboot the agent. other(1) is returned always when read. The following values are writable: coldReset(2)... warmReset(3)... |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
other(1), coldReset(2), warmReset(3) |
|
| agConfigForNxtReset |
1.3.6.1.4.1.1872.2.1.2.1.5 |
| The configuration information to be loaded from at next reset. The following values are writable: active(2)...active configuration block backup(3)...backup configuration block default(4)..default configuration block |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
active(2), backup(3), default(4) |
|
| agImageForNxtReset |
1.3.6.1.4.1.1872.2.1.2.1.6 |
| The software image to be booted from at next reset. The following values are writable: image1(2)...image 1 image2(3)...image 2 |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
image1(2), image2(3) |
|
| agSoftwareVersion |
1.3.6.1.4.1.1872.2.1.2.1.7 |
| The version of the software image that is currently running on the system in the form of 'major.minor.maintenance.bugfix'. A zero length string is returned if version is not available. |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
SIZE(0..16) |
|
| agBootVer |
1.3.6.1.4.1.1872.2.1.2.1.8 |
| The version of the boot code in the form of 'major.minor.bugfix'. A zero length string is returned if version is not available. |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
SIZE(0..16) |
|
| agImage1Ver |
1.3.6.1.4.1.1872.2.1.2.1.9 |
| The version of the software image stored in image 1 storage in the form of 'major.minor.maintenance.bugfix'. A zero length string is returned if version is not available or there is no valid software image. |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
SIZE(0..128) |
|
| agImage2Ver |
1.3.6.1.4.1.1872.2.1.2.1.10 |
| The version of the software image stored in image 2 storage in the form of 'major.minor.maintenance.bugfix'. A zero length string is returned if version is not available or there is no valid software image. |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
SIZE(0..128) |
|
| agRtcDate |
1.3.6.1.4.1.1872.2.1.2.1.11 |
| The date on the real time clock in the form of 'mm/dd/yy'. A zero length string is returned if date is not available. |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
SIZE(0..16) |
|
| agRtcTime |
1.3.6.1.4.1.1872.2.1.2.1.12 |
| The time on the real time clock in the form of 'hh:mm:ss'. A zero length string is returned if time is not available. |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
SIZE(0..16) |
|
| agTftpImage |
1.3.6.1.4.1.1872.2.1.2.1.15 |
| Whether the image file should be loaded in image1 or image2 in flash. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
image1(2), image2(3) |
|
| agTftpDownload |
1.3.6.1.4.1.1872.2.1.2.1.16 |
| This is an action object to cause to download software image according to the setup of agTftpServerIpAddr, agTftpImageFileName, agTftpImage when download(2) is issued. other(1) is returned always when read. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
other(1), download(2) |
|
| agTftpAction |
1.3.6.1.4.1.1872.2.1.2.1.21 |
| This is an action object to perform various TFTP Get or Put functions. The TFTP sever is specified in agTftpServer object. img-get(2) - Download switch image from a specified image file (agTftpImageFileName) on the TFTP server to the destinated storage (agTftpImage). cfg-get(3) - Download switch configuration from a specified file (agTftpCfgFileName) on the TFTP server. cfg-put(4) - Upload switch configuration to a specified file (agTftpCfgFileName) on the TFTP server. dump-put(5)- Download switch core dump to a specified file (agTftpDumpFileName) on the TFTP server. other(1) is returned always when read. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
other(1), img-get(2), cfg-get(3), cfg-put(4), dump-put(5) |
|
| agRevert |
1.3.6.1.4.1.1872.2.1.2.1.23 |
| This is an action object to revert the unapplied changes made to the switch. By setting the value to revert(2), all the unapplied changes will be reverted. This action will copy the current_config to the new_config block. other(1) is returned when this object is read. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
other(1), revert(2) |
|
| agRevertApply |
1.3.6.1.4.1.1872.2.1.2.1.24 |
| This is an action object to revert the unsaved changes made to the switch. By setting the value to revertApply(2), all the unsaved as well as unapplied changes will be reverted. other(1) is returned when this object is read. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
other(1), revertApply(2) |
|
| agSavePending |
1.3.6.1.4.1.1872.2.1.2.1.27 |
| This object, when read, gives the user information whether an save action is needed and that the configuration has been applied but not saved to the flash. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
saveNeeded(1), noSaveNeeded(2) |
|
| agEnabledGslbKey |
1.3.6.1.4.1.1872.2.1.2.1.28 |
| Query if software key Global slb enabled on switch. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| agEnabledBwmKey |
1.3.6.1.4.1.1872.2.1.2.1.29 |
| Query if software key Bandwidth Mgmt. enabled on switch. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| agSlotNumber |
1.3.6.1.4.1.1872.2.1.2.1.30 |
| Identifies the slot in which this switch is installed. If the agent implementing this MIB is not a blade in a chassis this value has no meaning. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..10 |
|
| agNewCfgBootp |
1.3.6.1.4.1.1872.2.1.2.2.3 |
| Enable or disable the use of BootP, in the new_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(2), disabled(3) |
|
| agCurCfgBootp |
1.3.6.1.4.1.1872.2.1.2.2.4 |
| Enable or disable the use of BootP, as currently configured in the current_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(2), disabled(3) |
|
| agNewCfgSpanningTree |
1.3.6.1.4.1.1872.2.1.2.2.5 |
| Turn On or Off Spanning Tree Protocol for the switch, in the new_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
on(2), off(3) |
|
| agCurCfgSpanningTree |
1.3.6.1.4.1.1872.2.1.2.2.6 |
| The state of Spanning Tree Protocol for the switch, as currently configured in the current_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
on(2), off(3) |
|
| agCurCfgTrapHostEntry |
1.3.6.1.4.1.1872.2.1.2.2.8.1 |
| A row in the trap host table in the current_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
AgCurCfgTrapHostEntry |
|
|
| agNewCfgTrapHostEntry |
1.3.6.1.4.1.1872.2.1.2.2.9.1 |
| A row in the trap host table in the new_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
AgNewCfgTrapHostEntry |
|
|
| agCurCfgHttpServerPort |
1.3.6.1.4.1.1872.2.1.2.2.10 |
| The TCP port number that the HTTP server is listening to in the current_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..65535 |
|
| agNewCfgHttpServerPort |
1.3.6.1.4.1.1872.2.1.2.2.11 |
| The TCP port number that the HTTP server is listening to in the new_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..65535 |
|
| agCurCfgSyslogFac |
1.3.6.1.4.1.1872.2.1.2.2.16 |
| The facility of syslog host in the current_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
local0(1), local1(2), local2(3), local3(4), local4(5), local5(6), local6(7), local7(8) |
|
| agNewCfgSyslogFac |
1.3.6.1.4.1.1872.2.1.2.2.17 |
| The facility of syslog host in the new_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
local0(1), local1(2), local2(3), local3(4), local4(5), local5(6), local6(7), local7(8) |
|
| agCurCfgSyslog2Fac |
1.3.6.1.4.1.1872.2.1.2.2.18 |
| The facility of syslog2 host in the current_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
local0(1), local1(2), local2(3), local3(4), local4(5), local5(6), local6(7), local7(8) |
|
| agNewCfgSyslog2Fac |
1.3.6.1.4.1.1872.2.1.2.2.19 |
| The facility of syslogs host in the new_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
local0(1), local1(2), local2(3), local3(4), local4(5), local5(6), local6(7), local7(8) |
|
| agCurCfgConsole |
1.3.6.1.4.1.1872.2.1.2.2.22 |
| Enable or disable console output of syslog messages. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| agNewCfgConsole |
1.3.6.1.4.1.1872.2.1.2.2.23 |
| Enable or disable console output of syslog messages. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| agNTP |
1.3.6.1.4.1.1872.2.1.2.2.28 |
| OBJECT IDENTIFIER |
|
|
|
| agLog |
1.3.6.1.4.1.1872.2.1.2.2.29 |
| OBJECT IDENTIFIER |
|
|
|
| agCurCfgSyslogTrapConsole |
1.3.6.1.4.1.1872.2.1.2.2.29.2 |
| Enable or disable console syslog and SNMP trap, as currently configured in the current_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| agNewCfgSyslogTrapSystem |
1.3.6.1.4.1.1872.2.1.2.2.29.3 |
| Enable or disable system level syslog and SNMP trap, in the new_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| agCurCfgSyslogTrapSystem |
1.3.6.1.4.1.1872.2.1.2.2.29.4 |
| Enable or disable system level syslog and SNMP trap, as currently configured in the current_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| agNewCfgSyslogTrapMgmt |
1.3.6.1.4.1.1872.2.1.2.2.29.5 |
| Enable or disable management(flash, config, login) syslog and SNMP trap, in the new_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| agCurCfgSyslogTrapMgmt |
1.3.6.1.4.1.1872.2.1.2.2.29.6 |
| Enable or disable management(flash, config, login) syslog and SNMP trap, as currently configured in the current_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| agNewCfgSyslogTrapCli |
1.3.6.1.4.1.1872.2.1.2.2.29.7 |
| Enable or disable CLI generated error syslog and SNMP trap, in the new_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| agCurCfgSyslogTrapCli |
1.3.6.1.4.1.1872.2.1.2.2.29.8 |
| Enable or disable CLI generated error syslog and SNMP trap, as currently configured in the current_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| agNewCfgSyslogTrapStp |
1.3.6.1.4.1.1872.2.1.2.2.29.9 |
| Enable or disable spanning tree syslog and SNMP trap, in the new_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| agCurCfgSyslogTrapStp |
1.3.6.1.4.1.1872.2.1.2.2.29.10 |
| Enable or disable spanning tree syslog and SNMP trap, as currently configured in the current_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| agNewCfgSyslogTrapVlan |
1.3.6.1.4.1.1872.2.1.2.2.29.11 |
| Enable or disable VLAN syslog and SNMP trap, in the new_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| agCurCfgSyslogTrapVlan |
1.3.6.1.4.1.1872.2.1.2.2.29.12 |
| Enable or disable VLAN syslog and SNMP trap, as currently configured in the current_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| agNewCfgSyslogTrapSlb |
1.3.6.1.4.1.1872.2.1.2.2.29.13 |
| Enable or disable SLB syslog and SNMP trap, in the new_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| agCurCfgSyslogTrapSlb |
1.3.6.1.4.1.1872.2.1.2.2.29.14 |
| Enable or disable SLB syslog and SNMP trap, as currently configured in the current_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| agNewCfgSyslogTrapGslb |
1.3.6.1.4.1.1872.2.1.2.2.29.15 |
| Enable or disable GSLB syslog and SNMP trap, in the new_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| agCurCfgSyslogTrapGslb |
1.3.6.1.4.1.1872.2.1.2.2.29.16 |
| Enable or disable GSLB syslog and SNMP trap, as currently configured in the current_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| agNewCfgSyslogTrapFilter |
1.3.6.1.4.1.1872.2.1.2.2.29.17 |
| Enable or disable filter syslog and SNMP trap, in the new_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| agCurCfgSyslogTrapFilter |
1.3.6.1.4.1.1872.2.1.2.2.29.18 |
| Enable or disable filter syslog and SNMP trap, as currently configured in the current_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| agNewCfgSyslogTrapSsh |
1.3.6.1.4.1.1872.2.1.2.2.29.19 |
| Enable or disable SSH, RADIUS syslog and SNMP trap, in the new_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| agCurCfgSyslogTrapSsh |
1.3.6.1.4.1.1872.2.1.2.2.29.20 |
| Enable or disable SSH, RADIUS syslog and SNMP trap, as currently configured in the current_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| agNewCfgSyslogTrapVrrp |
1.3.6.1.4.1.1872.2.1.2.2.29.21 |
| Enable or disable VRRP syslog and SNMP trap, in the new_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| agCurCfgSyslogTrapVrrp |
1.3.6.1.4.1.1872.2.1.2.2.29.22 |
| Enable or disable VRRP syslog and SNMP trap, as currently configured in the current_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| agNewCfgSyslogTrapBgp |
1.3.6.1.4.1.1872.2.1.2.2.29.23 |
| Enable or disable BGP syslog and SNMP trap, in the new_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| agCurCfgSyslogTrapBgp |
1.3.6.1.4.1.1872.2.1.2.2.29.24 |
| Enable or disable BGP syslog and SNMP trap, as currently configured in the current_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| agNewCfgSyslogTrapNtp |
1.3.6.1.4.1.1872.2.1.2.2.29.25 |
| Enable or disable NTP syslog and SNMP trap, in the new_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| agCurCfgSyslogTrapNtp |
1.3.6.1.4.1.1872.2.1.2.2.29.26 |
| Enable or disable NTP syslog and SNMP trap, as currently configured in the current_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| agNewCfgSyslogTrapIsd |
1.3.6.1.4.1.1872.2.1.2.2.29.27 |
| Enable or disable ISD syslog and SNMP trap, in the new_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| agCurCfgSyslogTrapIsd |
1.3.6.1.4.1.1872.2.1.2.2.29.28 |
| Enable or disable ISD syslog and SNMP trap, as currently configured in the current_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| agNewCfgSyslogTrapIp |
1.3.6.1.4.1.1872.2.1.2.2.29.31 |
| Enable or disable IP related syslog and SNMP trap, in the new_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| agCurCfgSyslogTrapIp |
1.3.6.1.4.1.1872.2.1.2.2.29.32 |
| Enable or disable IP related syslog and SNMP trap, as currently configured in the current_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| agNewCfgSyslogTrapWeb |
1.3.6.1.4.1.1872.2.1.2.2.29.35 |
| Enable or disable WEBUI related syslog and SNMP trap, in the new_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| agCurCfgSyslogTrapWeb |
1.3.6.1.4.1.1872.2.1.2.2.29.36 |
| Enable or disable WEBUI related syslog and SNMP trap, as currently configured in the current_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| agNewCfgSyslogTrapSynAtk |
1.3.6.1.4.1.1872.2.1.2.2.29.37 |
| Enable or disable SYN attack detection related syslog and SNMP trap, in the new_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| agCurCfgSyslogTrapSynAtk |
1.3.6.1.4.1.1872.2.1.2.2.29.38 |
| Enable or disable SYN attack detection related syslog and SNMP trap, as currently configured in the current_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| agNewCfgSyslogTrapTcpLim |
1.3.6.1.4.1.1872.2.1.2.2.29.39 |
| Enable or disable TCP rate limiting related syslog and SNMP trap, in the new_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| agCurCfgSyslogTrapTcpLim |
1.3.6.1.4.1.1872.2.1.2.2.29.40 |
| Enable or disable TCP rate limiting related syslog and SNMP trap, as currently configured in the current_configuration block. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| stats |
1.3.6.1.4.1.1872.2.1.8 |
| OBJECT IDENTIFIER |
|
|
|
| memStats |
1.3.6.1.4.1.1872.2.1.8.12 |
| OBJECT IDENTIFIER |
|
|
|
| pktStats |
1.3.6.1.4.1.1872.2.1.8.13 |
| OBJECT IDENTIFIER |
|
|
|
| mpCpuStats |
1.3.6.1.4.1.1872.2.1.8.16 |
| OBJECT IDENTIFIER |
|
|
|
| operCmds |
1.3.6.1.4.1.1872.2.1.14 |
| OBJECT IDENTIFIER |
|
|
|
| radius |
1.3.6.1.4.1.1872.2.1.16 |
| OBJECT IDENTIFIER |
|
|
|
| radCurCfgTimeout |
1.3.6.1.4.1.1872.2.1.16.7 |
| The maximum number of seconds before resending authentication to RADIUS server. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..10 |
|
| radNewCfgTimeout |
1.3.6.1.4.1.1872.2.1.16.8 |
| The maximum number of seconds before resending authentication to RADIUS server. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..10 |
|
| radCurCfgState |
1.3.6.1.4.1.1872.2.1.16.11 |
| Enable or disbale RADIUS authentication. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(2), disabled(3) |
|
| radNewCfgState |
1.3.6.1.4.1.1872.2.1.16.12 |
| Enable or disable RADIUS authentication. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(2), disabled(3) |
|
| radCurCfgTelnet |
1.3.6.1.4.1.1872.2.1.16.15 |
| Enable or disbale RADIUS backdoor for telnet. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| radNewCfgTelnet |
1.3.6.1.4.1.1872.2.1.16.16 |
| Enable or disable RADIUS backdoor for telnet. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
Defined Objects
| AgCurCfgTrapHostEntry |
|
| SEQUENCE |
|
|
|
| |
INTEGER as agCurCfgTrapHostIndx |
|
|
| |
IpAddress as agCurCfgTrapHostIpAddr |
|
|
| |
DisplayString as agCurCfgTrapHostCommString |
|
|
| AgNewCfgTrapHostEntry |
|
| SEQUENCE |
|
|
|
| |
INTEGER as agNewCfgTrapHostIndx |
|
|
| |
IpAddress as agNewCfgTrapHostIpAddr |
|
|
| |
DisplayString as agNewCfgTrapHostCommString |
|
|