
| APPIAN-SMI-MIB | APPIAN-CHASSIS-MIB | SNMPv2-SMI |
| SNMPv2-TC |
| acPport | AcAdminStatus | AcOpStatus |
| AcNodeId | acChassisCurrentTime | acChassisRingId |
| MODULE-IDENTITY | OBJECT-TYPE | IpAddress |
| NOTIFICATION-TYPE | DisplayString |
| acSerial | 1.3.6.1.4.1.2785.2.3.2 | ||
| Appian Serial Interface MIB for RS232 like interfaces. | |||
| MODULE-IDENTITY | |||
| acSerialTraps | 1.3.6.1.4.1.2785.2.3.2.0 | ||
| OBJECT IDENTIFIER | |||
| acSerialLinkDownTrap | 1.3.6.1.4.1.2785.2.3.2.0.1 | ||
| The Serial Port driver for this interface has detected the port to be in the down state. | |||
| NOTIFICATION-TYPE | |||
| acChassisCurrentTime | |||
| acChassisRingId | |||
| acSerialNodeId | |||
| acSerialSlot | |||
| acSerialPort | |||
| acSerialLinkUpTrap | 1.3.6.1.4.1.2785.2.3.2.0.2 | ||
| The Serial Port driver for this interface has detected the port to be in the down state. | |||
| NOTIFICATION-TYPE | |||
| acChassisCurrentTime | |||
| acChassisRingId | |||
| acSerialNodeId | |||
| acSerialSlot | |||
| acSerialPort | |||
| acSerialStatsResetTrap | 1.3.6.1.4.1.2785.2.3.2.0.3 | ||
| The statistics for this serial port have been reset to zero(0) and may cause problems for long term trending functions. | |||
| NOTIFICATION-TYPE | |||
| acChassisCurrentTime | |||
| acChassisRingId | |||
| acSerialNodeId | |||
| acSerialSlot | |||
| acSerialPort | |||
| acSerialCfgErrorTrap | 1.3.6.1.4.1.2785.2.3.2.0.4 | ||
| A configuration request for this serial interface has been detected as incorrect or corrupted. | |||
| NOTIFICATION-TYPE | |||
| acChassisCurrentTime | |||
| acChassisRingId | |||
| acSerialNodeId | |||
| acSerialSlot | |||
| acSerialPort | |||
| acSerialOpCode | |||
| acSerialTable | 1.3.6.1.4.1.2785.2.3.2.1 | ||
| Each Switch Control Processor supports a debug port as well as a management access or craft CLI port. The system will initialize the acSerialTable when the system boots or an SCP has been reset. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AcSerialEntry | |||
| acSerialEntry | 1.3.6.1.4.1.2785.2.3.2.1.1 | ||
| A row in the serial table contains configurable parameters and statistics for each serial interface on this platform. | |||
| OBJECT-TYPE | |||
| AcSerialEntry | |||
| acSerialNodeId | 1.3.6.1.4.1.2785.2.3.2.1.1.1 | ||
| The node id is the id for this specific node in the OSAP ring. | |||
| OBJECT-TYPE | |||
| AcNodeId | |||
| acSerialSlot | 1.3.6.1.4.1.2785.2.3.2.1.1.2 | ||
| The control processor slot upon which the serial port is located. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..4 | ||
| acSerialPort | 1.3.6.1.4.1.2785.2.3.2.1.1.3 | ||
| The physical port number on acSerialEntrySlot where this connector is located. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..2 | ||
| acSerialAdminStatus | 1.3.6.1.4.1.2785.2.3.2.1.1.4 | ||
| Appian Administrative Status attribute used to set the provisioning state as either activate(1), inactivate(2) or delete(3). Refer to the Appian-SMI.mib file for additional information. | |||
| OBJECT-TYPE | |||
| AcAdminStatus | |||
| acSerialOpStatus | 1.3.6.1.4.1.2785.2.3.2.1.1.5 | ||
| The current operational status of the serial port driver and services supporting this interface. | |||
| OBJECT-TYPE | |||
| AcOpStatus | |||
| acSerialOpCode | 1.3.6.1.4.1.2785.2.3.2.1.1.6 | ||
| Provides a detailed status code which can be used to isolate a problem or state condition reported in acSerialEntryOpStatus. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| acSerialOpMode | 1.3.6.1.4.1.2785.2.3.2.1.1.7 | ||
| Determines the mode of operation for the serial port. If the serial port is using a raw terminal(1) or if we are to run PPP over this port as an alternative EMS access mechanism. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(0), terminal(1), ppp(2) | ||
| acSerialBaudRate | 1.3.6.1.4.1.2785.2.3.2.1.1.8 | ||
| User configured baud rate for use on the serial port. When set to Auto(1), the driver will negotiate baud rate. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(0), auto(1), baud9600(2), baud19200(3), baud56000(4), baud64000(5), baud115000(6) | ||
| acSerialParity | 1.3.6.1.4.1.2785.2.3.2.1.1.9 | ||
| User configurable partity which is used on the serial port. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(0), none(1), odd(2), even(3) | ||
| acSerialNumberBits | 1.3.6.1.4.1.2785.2.3.2.1.1.10 | ||
| Number of bits-per-byte used over the serial port. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(0), bits-7(1), bits-8(2) | ||
| acSerialIpAddress | 1.3.6.1.4.1.2785.2.3.2.1.1.11 | ||
| The IP Addressed used on the serial port during PPP sessions. If chSerialMode is equal to PPP-DHCP, this field is not needed otherwise a static IP Address is required in this field. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| acSerialIpSubnet | 1.3.6.1.4.1.2785.2.3.2.1.1.12 | ||
| The IP Subnet Mask in dotted notation for use on the serial port during PPP sessions. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| acSerialRxOctets | 1.3.6.1.4.1.2785.2.3.2.1.1.13 | ||
| The number of bytes read by the serial port driver. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| acSerialTxOctets | 1.3.6.1.4.1.2785.2.3.2.1.1.14 | ||
| The number of bytes transmitted by the serial port driver. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| acSerialInterfaceName | 1.3.6.1.4.1.2785.2.3.2.1.1.15 | ||
| A user configurable ASCII name of up to 64 bytes in length, which is assigned for this interface. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..64) | ||
| AcSerialEntry | |||
| SEQUENCE | |||
| AcNodeId as acSerialNodeId | |||
| INTEGER as acSerialSlot | |||
| INTEGER as acSerialPort | |||
| AcAdminStatus as acSerialAdminStatus | |||
| AcOpStatus as acSerialOpStatus | |||
| INTEGER as acSerialOpCode | |||
| INTEGER as acSerialOpMode | |||
| INTEGER as acSerialBaudRate | |||
| INTEGER as acSerialParity | |||
| INTEGER as acSerialNumberBits | |||
| IpAddress as acSerialIpAddress | |||
| IpAddress as acSerialIpSubnet | |||
| INTEGER as acSerialRxOctets | |||
| INTEGER as acSerialTxOctets | |||
| DisplayString as acSerialInterfaceName | |||