APTIS-ACTIONS-MIB

File: APTIS-ACTIONS-MIB.mib (19405 bytes)

Imported modules

APTIS-MIB APTIS-REG-MIB SNMPv2-SMI
SNMPv2-TC

Imported symbols

aptis-actions Boolean aptis-modules
MODULE-IDENTITY OBJECT-TYPE IpAddress
DisplayString RowStatus

Defined Objects

aptisActionsModule 1.3.6.1.4.1.2637.1.1.5
The following variables describe the administrative actions that may be invoked through SNMP.
MODULE-IDENTITY    

slotControlTable 1.3.6.1.4.1.2637.2.3.203
slot control
OBJECT-TYPE    
  SEQUENCE OF  
    SlotControlEntry

slotControlEntry 1.3.6.1.4.1.2637.2.3.203.1
This is the structure of entries in the slotControlTable.
OBJECT-TYPE    
  SlotControlEntry  

slotControlInstance 1.3.6.1.4.1.2637.2.3.203.1.1
Each invocation of this action will have a unique instance number, assigned by the switch.
OBJECT-TYPE    
  INTEGER  

slotControlStatusGeneral 1.3.6.1.4.1.2637.2.3.203.1.2
like, did it work, or what? This is the standard actionStatus enum used for all actions.
OBJECT-TYPE    
  INTEGER started(0), succeeded(1), failed(2), errParam(4)  

slotControlStatusSpecific 1.3.6.1.4.1.2637.2.3.203.1.3
like, did it work, or what? If the generalStatus is err-param or failed, this will hold a more specific error number.
OBJECT-TYPE    
  INTEGER unknown(0), noCard(1), notAllowed(2), badSlot(3), inUse(4), inappropriate(5)  

slotControlSlotIndex 1.3.6.1.4.1.2637.2.3.203.1.11
The physical slot number.
OBJECT-TYPE    
  INTEGER 1..18  

slotControlSlotAction 1.3.6.1.4.1.2637.2.3.203.1.12
The action requested for this slot.
OBJECT-TYPE    
  INTEGER slotNoChange(0), slotDown(1), slotDownPend(2), slotUp(3), slotReset(4), slotDownTimed(5), slotAbortDry(6)  

sessionTerminateTable 1.3.6.1.4.1.2637.2.3.230
This action allows a remote manager to terminate an active session.
OBJECT-TYPE    
  SEQUENCE OF  
    SessionTerminateEntry

sessionTerminateEntry 1.3.6.1.4.1.2637.2.3.230.1
This is the structure of entries in the sessionTerminateTable.
OBJECT-TYPE    
  SessionTerminateEntry  

sessionTerminateInstance 1.3.6.1.4.1.2637.2.3.230.1.1
Each invocation of this action will have a unique instance number, assigned by the switch.
OBJECT-TYPE    
  INTEGER  

sessionTerminateStatusGeneral 1.3.6.1.4.1.2637.2.3.230.1.2
This is the standard actionStatus enum used for all actions.
OBJECT-TYPE    
  INTEGER started(0), succeeded(1), failed(2), errParam(4)  

sessionTerminateStatusSpecific 1.3.6.1.4.1.2637.2.3.230.1.3
If generalStatus is err-param or failed, this will hold a more specific error number.
OBJECT-TYPE    
  INTEGER noError(0), badSignature(1), badSession(2), genFail(3)  

sessionTerminateBootEra 1.3.6.1.4.1.2637.2.3.230.1.11
An input parameter to the session-terminate action. Together with the sessionID, uniquely identifies the session to terminate. If a value is provided, it must match the current value of bootEra, so this field is only provided as a safeguard to ensure that sessions from the wrong boot era can't be terminated accidentally.
OBJECT-TYPE    
  INTEGER  

sessionTerminateSessionID 1.3.6.1.4.1.2637.2.3.230.1.12
An input parameter to the session-terminate action, naming the session which should be terminated.
OBJECT-TYPE    
  INTEGER  

sessionTerminateSignature 1.3.6.1.4.1.2637.2.3.230.1.13
An input parameter to the session-terminate action, providing a cryptographically secure verification that the manager requesting the termination has the appropriate credentials to do so. NOTE: the exact algorithm for generating the signature has not yet been determined.
OBJECT-TYPE    
  DisplayString  

t1TestTable 1.3.6.1.4.1.2637.2.3.2106
T1 Testing Control.
OBJECT-TYPE    
  SEQUENCE OF  
    T1TestEntry

t1TestEntry 1.3.6.1.4.1.2637.2.3.2106.1
This is the structure of entries in the t1TestTable.
OBJECT-TYPE    
  T1TestEntry  

t1TestInstance 1.3.6.1.4.1.2637.2.3.2106.1.1
T1 Test Instance.
OBJECT-TYPE    
  INTEGER  

t1TestTestType 1.3.6.1.4.1.2637.2.3.2106.1.2
type of test to run.
OBJECT-TYPE    
  INTEGER ones(1), zeros(2), fives(3), qrss(4)  

t1TestSlotNumber 1.3.6.1.4.1.2637.2.3.2106.1.3
ID of the slot to run the test on.
OBJECT-TYPE    
  INTEGER slot1(1), slot2(2), slot3(3), slot4(4), slot5(5), slot6(6), slot7(7), slot8(8), slot11(11), slot12(12), slot13(13), slot14(14), slot15(15), slot16(16), slot17(17), slot18(18)  

t1TestPortNumber 1.3.6.1.4.1.2637.2.3.2106.1.4
ID of the DS1 to run the test on.
OBJECT-TYPE    
  INTEGER ds11(1), ds12(2), ds13(3), ds14(4), ds15(5), ds16(6), ds17(7), ds18(8), ds19(9), ds110(10), ds111(11), ds112(12), ds113(13), ds114(14), ds115(15), ds116(16), ds117(17), ds118(18), ds119(19), ds120(20), ds121(21), ds122(22), ds123(23), ds124(24), ds125(25), ds126(26), ds127(27), ds128(28), ds129(29), ds130(30), ds131(31), ds132(32), ds133(33), ds134(34), ds135(35), ds136(36), ds137(37), ds138(38), ds139(39), ds140(40), ds141(41), ds142(42), ds143(43), ds144(44), ds145(45), ds146(46), ds147(47), ds148(48), ds149(49), ds150(50), ds151(51), ds152(52), ds153(53), ds154(54), ds155(55), ds156(56)  

t1TestTestLength 1.3.6.1.4.1.2637.2.3.2106.1.5
number of bytes of data to send.
OBJECT-TYPE    
  INTEGER 1..30000  

t1TestErrorRate 1.3.6.1.4.1.2637.2.3.2106.1.6
percentage of data received with errors.
OBJECT-TYPE    
  INTEGER 0..100  

t1TestState 1.3.6.1.4.1.2637.2.3.2106.1.7
current state of test.
OBJECT-TYPE    
  INTEGER initializing(1), loopingUp(2), sendingData(3), checkingResults(4), loopingDown(5), complete(6), failed(7), cancelled(8)  

flashWriteTable 1.3.6.1.4.1.2637.2.3.3501
This action causes a portion of the configuration subtree to be written out to a text file on one of the CVX system's local flash cards.
OBJECT-TYPE    
  SEQUENCE OF  
    FlashWriteEntry

flashWriteEntry 1.3.6.1.4.1.2637.2.3.3501.1
This is the structure of entries in the flashWriteTable.
OBJECT-TYPE    
  FlashWriteEntry  

flashWriteInstance 1.3.6.1.4.1.2637.2.3.3501.1.1
Each invocation of this action will have a unique instance number, assigned by the switch.
OBJECT-TYPE    
  INTEGER  

flashWriteStatusGeneral 1.3.6.1.4.1.2637.2.3.3501.1.2
This is the standard actionStatus enum used for all actions.
OBJECT-TYPE    
  INTEGER started(0), succeeded(1), failed(2), errParam(4)  

flashWriteStatusSpecific 1.3.6.1.4.1.2637.2.3.3501.1.3
If generalStatus is err-param or failed, this will hold a more specific error number.
OBJECT-TYPE    
  INTEGER noError(0), badArgs(1), lackOfResources(2), genFail(3)  

flashWritePathString 1.3.6.1.4.1.2637.2.3.3501.1.11
The starting node in the configuration tree. The contents of all the nodes under this node will be written out to the text file.
OBJECT-TYPE    
  DisplayString  

flashWriteFileName 1.3.6.1.4.1.2637.2.3.3501.1.12
The relative file name to hold the text config. The CVX file system uses drive C: to refer to the bottom flash card, and D: to refer to the top flash card. If the drive letter is not specified, then C: is assumed. If this file exists, it will only be overwritten with a complete copy of the output from this action. NOTE that the file CONFIG.CVX is not accessible through this action. To save the config to flash where it will be used at the next reboot, use the flashSave action instead.
OBJECT-TYPE    
  DisplayString SIZE(0..16)  

flashWriteBytesWritten 1.3.6.1.4.1.2637.2.3.3501.1.13
On success, the total number of bytes written to flash.
OBJECT-TYPE    
  INTEGER  

flashWriteVerboseMode 1.3.6.1.4.1.2637.2.3.3501.1.14
Setting this field to TRUE requests that the output file contain all configuration values, otherwise only those that differ from the default values.
OBJECT-TYPE    
  Boolean  

flashReadTable 1.3.6.1.4.1.2637.2.3.3502
This action causes the configuration subtree to be read to one of the CVX system's local flash cards.
OBJECT-TYPE    
  SEQUENCE OF  
    FlashReadEntry

flashReadEntry 1.3.6.1.4.1.2637.2.3.3502.1
This is the structure of entries in the flashReadTable.
OBJECT-TYPE    
  FlashReadEntry  

flashReadInstance 1.3.6.1.4.1.2637.2.3.3502.1.1
Each invocation of this action will have a unique instance number, assigned by the switch.
OBJECT-TYPE    
  INTEGER  

flashReadStatusGeneral 1.3.6.1.4.1.2637.2.3.3502.1.2
This is the standard actionStatus enum used for all actions.
OBJECT-TYPE    
  INTEGER started(0), succeeded(1), failed(2), badFile(4), genFail(5)  

flashReadFileName 1.3.6.1.4.1.2637.2.3.3502.1.12
The relative file name to hold the text config. The CVX file system uses drive C: to refer to the bottom flash card, and D: to refer to the top flash card. If the drive letter is not specified, then C: is assumed.
OBJECT-TYPE    
  DisplayString SIZE(0..16)  

flashReadLinesRead 1.3.6.1.4.1.2637.2.3.3502.1.13
On success, the total number of lines read from flash.
OBJECT-TYPE    
  INTEGER  

flashSaveTable 1.3.6.1.4.1.2637.2.3.3503
This action saves the configuration to the flash file CONFIG.CVX. It is equivalent to the 'write' command in the CLI.
OBJECT-TYPE    
  SEQUENCE OF  
    FlashSaveEntry

flashSaveEntry 1.3.6.1.4.1.2637.2.3.3503.1
This is the structure of entries in the flashSaveTable.
OBJECT-TYPE    
  FlashSaveEntry  

flashSaveInstance 1.3.6.1.4.1.2637.2.3.3503.1.1
Each invocation of this action will have a unique instance number, assigned by the switch.
OBJECT-TYPE    
  INTEGER  

flashSaveStatusGeneral 1.3.6.1.4.1.2637.2.3.3503.1.2
This is the standard actionStatus enum used for all actions.
OBJECT-TYPE    
  INTEGER started(0), succeeded(1), failed(2), errParam(4)  

flashSaveStatusSpecific 1.3.6.1.4.1.2637.2.3.3503.1.3
If generalStatus is err-param or failed, this will hold a more specific error number.
OBJECT-TYPE    
  INTEGER noError(0), lackOfResources(2), genFail(3)  

resetTable 1.3.6.1.4.1.2637.2.3.3510
CVX Chassis Options.
OBJECT-TYPE    
  SEQUENCE OF  
    ResetEntry

resetEntry 1.3.6.1.4.1.2637.2.3.3510.1
This is the structure of entries in the resetTable.
OBJECT-TYPE    
  ResetEntry  

resetInstance 1.3.6.1.4.1.2637.2.3.3510.1.1
Each invocation of this action will have a unique instance number, assigned by the switch.
OBJECT-TYPE    
  INTEGER  

resetStatusGeneral 1.3.6.1.4.1.2637.2.3.3510.1.2
This is the standard actionStatus enum used for all actions.
OBJECT-TYPE    
  INTEGER started(0), succeeded(1), failed(2), errParam(4)  

resetResetType 1.3.6.1.4.1.2637.2.3.3510.1.11
Select the type of reset requested.
OBJECT-TYPE    
  INTEGER hard(1), cold(2), warm(3)  

Defined Objects

ResetEntry  
SEQUENCE    
  INTEGER as resetInstance  
  INTEGER as resetStatusGeneral  
  INTEGER as resetResetType  

FlashWriteEntry  
SEQUENCE    
  INTEGER as flashWriteInstance  
  INTEGER as flashWriteStatusGeneral  
  INTEGER as flashWriteStatusSpecific  
  DisplayString as flashWritePathString  
  DisplayString as flashWriteFileName  
  INTEGER as flashWriteBytesWritten  
  Boolean as flashWriteVerboseMode  

FlashReadEntry  
SEQUENCE    
  INTEGER as flashReadInstance  
  INTEGER as flashReadStatusGeneral  
  DisplayString as flashReadFileName  
  INTEGER as flashReadLinesRead  

FlashSaveEntry  
SEQUENCE    
  INTEGER as flashSaveInstance  
  INTEGER as flashSaveStatusGeneral  
  INTEGER as flashSaveStatusSpecific  

SessionTerminateEntry  
SEQUENCE    
  INTEGER as sessionTerminateInstance  
  INTEGER as sessionTerminateStatusGeneral  
  INTEGER as sessionTerminateStatusSpecific  
  INTEGER as sessionTerminateBootEra  
  INTEGER as sessionTerminateSessionID  
  DisplayString as sessionTerminateSignature  

SlotControlEntry  
SEQUENCE    
  INTEGER as slotControlInstance  
  INTEGER as slotControlStatusGeneral  
  INTEGER as slotControlStatusSpecific  
  INTEGER as slotControlSlotIndex  
  INTEGER as slotControlSlotAction  

T1TestEntry  
SEQUENCE    
  INTEGER as t1TestInstance  
  INTEGER as t1TestTestType  
  INTEGER as t1TestSlotNumber  
  INTEGER as t1TestPortNumber  
  INTEGER as t1TestTestLength  
  INTEGER as t1TestErrorRate  
  INTEGER as t1TestState