
ASCEND-CALL-LOGGING-MIB
File:
ASCEND-CALL-LOGGING-MIB.mib (7074 bytes)
Imported modules
Imported symbols
Defined Objects
| callLoggingServerEntry |
1.3.6.1.4.1.529.25.2.1 |
| Entry holding information about the currently active Call Logging Server and the address of a Server. |
| OBJECT-TYPE |
|
|
|
| |
CallLoggingServerEntry |
|
|
| callLoggingServerIndex |
1.3.6.1.4.1.529.25.2.1.1 |
| The index number for this Call Logging server entry. Its value ranges from 1 to 'callLoggingNumServers'. and identifies which server entry is associated with. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| callLoggingEnableActiveServer |
1.3.6.1.4.1.529.25.2.1.4 |
| This is used to set the active call Logging server. If set to enable(2) it will enable the call Logging server, A read on the variable will return notApplicable(1). |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
notApplicable(1), enable(2) |
|
| callLoggingStatus |
1.3.6.1.4.1.529.25.3 |
| Enable/Disable call loggin support. Note: Prior to enable the call Logging, one of the Call Logging server must be setup with a valid IP address. If the server IP address is not setup, a SET to this object will return with a bad value error. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| callLoggingKey |
1.3.6.1.4.1.529.25.5 |
| The (RADIUS_ACCT) call logging key to access server. |
| OBJECT-TYPE |
|
|
|
| |
OCTET STRING |
SIZE(0..20) |
|
| callLoggingTimeout |
1.3.6.1.4.1.529.25.6 |
| Number of seconds to wait for a response to previous Call Logging request sent to server. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| callLoggingIdBase |
1.3.6.1.4.1.529.25.7 |
| The Base to use in reporting Call Logging ID. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
other(1), invalid(2), base10(10), base16(16) |
|
| callLoggingStopPacketsOnly |
1.3.6.1.4.1.529.25.9 |
| Send call log Stop packets that have username=0. These are caused by connections that are dropped before authentication is done. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| callLoggingRetryLimit |
1.3.6.1.4.1.529.25.10 |
| Number of retries before removing Call Logging packet. 0 means leave on retry list until maximum retry entries are exceeded. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| callLoggingAssStatus |
1.3.6.1.4.1.529.25.11 |
| Indicates the status of Active Session Snapshot protocol. Writing the attribute with a nonzero value causes the start of an Active Session Snapshot. If no server is configured the Active Session Snapshot will abort immediatly, an active session can not be aborted |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
idle(1), active(2), aborted(3) |
|
| callLoggingRadCompatMode |
1.3.6.1.4.1.529.25.13 |
| Indicates call logging RADIUS compatibility mode. This variable is deprecated, starting with TAOS Release 8.0. this variable has a fixed value of radVendorSpecific(4) |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
other(1), invalid(2), radOldAscend(3), radVendorSpecific(4) |
|
Defined Objects
| CallLoggingServerEntry |
|
| SEQUENCE |
|
|
|
| |
INTEGER as callLoggingServerIndex |
|
|
| |
INTEGER as callLoggingCurrentServerFlag |
|
|
| |
IpAddress as callLoggingServerIPAddress |
|
|
| |
INTEGER as callLoggingEnableActiveServer |
|
|