
| ASCEND-WAN-MIB | RFC-1212 |
| wanTypeHdsl2 | OBJECT-TYPE |
| hdsl2LineStatusTable | 1.3.6.1.4.1.529.4.12.1 | ||
| HDSL2 status parameters. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| Hdsl2LineStatusEntry | |||
| hdsl2LineStatusEntry | 1.3.6.1.4.1.529.4.12.1.1 | ||
| A interface status entry containing objects to describe the interface. | |||
| OBJECT-TYPE | |||
| Hdsl2LineStatusEntry | |||
| hdsl2StatusIfEntryIndex | 1.3.6.1.4.1.529.4.12.1.1.1 | ||
| Interface group index assigned to this port. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| hdsl2StatusShelfIndex | 1.3.6.1.4.1.529.4.12.1.1.2 | ||
| TNT's HDSL2 modules Shelf ID. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| hdsl2StatusSlotIndex | 1.3.6.1.4.1.529.4.12.1.1.3 | ||
| TNT's HDSL2 modules Slot ID. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| hdsl2StatusLineIndex | 1.3.6.1.4.1.529.4.12.1.1.4 | ||
| HDSL2 modules line ID. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| hdsl2StatusUnitType | 1.3.6.1.4.1.529.4.12.1.1.5 | ||
| Unit type defines if the unit is operating either as a Central Office Equipment (COE) or Customer Premiss equipment (CPE). | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), coe(2), cpe(3) | ||
| hdsl2StatusLineState | 1.3.6.1.4.1.529.4.12.1.1.6 | ||
| Interface state describes the current ports operating state. States are: Config, Pend Down, Up, Down, Start-up, or N/A. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), configure(2), deactivate(3), deactive-lost(4), start-up(5), pend-port-up(6), up(7), pend-deactivate(8), out-of-service(9), analog-loopback(10), digital-loopback(11) | ||
| hdsl2StatusOpRate | 1.3.6.1.4.1.529.4.12.1.1.7 | ||
| The current symetrical operation rate | |||
| OBJECT-TYPE | |||
| INTEGER | m1552000(1552000) | ||
| hdsl2StatusVendorId | 1.3.6.1.4.1.529.4.12.1.1.8 | ||
| Vendor identification. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| hdsl2StatusMajorFirmWareVer | 1.3.6.1.4.1.529.4.12.1.1.9 | ||
| Major firmware version. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| hdsl2StatusMinorFirmWareVer | 1.3.6.1.4.1.529.4.12.1.1.10 | ||
| Minor firmware version. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| hdsl2StatusHardWareVer | 1.3.6.1.4.1.529.4.12.1.1.11 | ||
| Hardware version. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| hdsl2LineStatisticTable | 1.3.6.1.4.1.529.4.12.2 | ||
| HDSL2 statistical parameters. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| Hdsl2LineStatisticEntry | |||
| hdsl2LineStatisticEntry | 1.3.6.1.4.1.529.4.12.2.1 | ||
| A interface statistical entry containing objects to describe the interface. | |||
| OBJECT-TYPE | |||
| Hdsl2LineStatisticEntry | |||
| hdsl2StatIfEntryIndex | 1.3.6.1.4.1.529.4.12.2.1.1 | ||
| The interface groups interface index is used to index into this table. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| hdsl2StatShelfIndex | 1.3.6.1.4.1.529.4.12.2.1.2 | ||
| HDSL2 modules Shelf ID. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| hdsl2StatSlotIndex | 1.3.6.1.4.1.529.4.12.2.1.3 | ||
| HDSL2 modules Slot ID. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| hdsl2StatLineIndex | 1.3.6.1.4.1.529.4.12.2.1.4 | ||
| HDSL2 modules interface ID. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| hdsl2StatConnUpDays | 1.3.6.1.4.1.529.4.12.2.1.5 | ||
| Connection up day count. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| hdsl2StatConnUpHours | 1.3.6.1.4.1.529.4.12.2.1.6 | ||
| Connection Up 24 hour count. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| hdsl2StatConnUpMinutes | 1.3.6.1.4.1.529.4.12.2.1.7 | ||
| Connection up minute count. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| hdsl2StatRxSignalPresent | 1.3.6.1.4.1.529.4.12.2.1.8 | ||
| Receive signal present detection. | |||
| OBJECT-TYPE | |||
| INTEGER | no(1), yes(2) | ||
| hdsl2StatLineQualityDb | 1.3.6.1.4.1.529.4.12.2.1.9 | ||
| Lines noise margin. Reliable data will transfer with a reading of ??? or greater. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| hdsl2StatUpDwnCntr | 1.3.6.1.4.1.529.4.12.2.1.10 | ||
| Line Up Down counter value displays the number of times the interface transitions from a down to up state. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| hdsl2StatLineSelfTest | 1.3.6.1.4.1.529.4.12.2.1.11 | ||
| Line hardware self test results (Passed or Failed). | |||
| OBJECT-TYPE | |||
| INTEGER | other(4), selfTestFailed(1), localLoopBackFailed(2), passed(3) | ||
| hdsl2StatTxPower | 1.3.6.1.4.1.529.4.12.2.1.12 | ||
| Lines transmit power. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..'7fffffff'h | ||
| hdsl2StatFramerCrcErrors | 1.3.6.1.4.1.529.4.12.2.1.13 | ||
| Lines framer CRC errors. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..'7fffffff'h | ||
| hdsl2StatFramerSyncStatus | 1.3.6.1.4.1.529.4.12.2.1.14 | ||
| Lines framer sync status . | |||
| OBJECT-TYPE | |||
| INTEGER | 1..'7fffffff'h | ||
| hdsl2StatFramerLosdCnt | 1.3.6.1.4.1.529.4.12.2.1.15 | ||
| Lines framer ???. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..'7fffffff'h | ||
| hdsl2StatFramerSegaCnt | 1.3.6.1.4.1.529.4.12.2.1.16 | ||
| Lines framer ???. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..'7fffffff'h | ||
| hdsl2StatFramerSegdCnt | 1.3.6.1.4.1.529.4.12.2.1.17 | ||
| Lines framer ???. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..'7fffffff'h | ||
| hdsl2StatFramerRxHecErrors | 1.3.6.1.4.1.529.4.12.2.1.18 | ||
| Lines framer ???. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..'7fffffff'h | ||
| hdsl2StatBertTimer | 1.3.6.1.4.1.529.4.12.2.1.19 | ||
| BER test duration configuration. The BER test lasts for the duration of this timer. | |||
| OBJECT-TYPE | |||
| INTEGER | one-minute(1), two-minutes(2), three-minutes(3), four-minutes(4), five-minutes(5), ten-minutes(6), fifteen-minutes(7), twenty-minutes(8), thirty-minutes(9) | ||
| hdsl2StatBertEna | 1.3.6.1.4.1.529.4.12.2.1.20 | ||
| Enable/disable of the BER test. If nodes are connected, then the BER test is ran between the units. If this node is not connected to a remote node, then the interface is placed into analog loopback and the BER test is started. | |||
| OBJECT-TYPE | |||
| INTEGER | no(1), yes(2) | ||
| hdsl2StatBertState | 1.3.6.1.4.1.529.4.12.2.1.21 | ||
| BER test states. When this node is not connected to another node, the test is disabled. When two nodes are connected then the BER test waits for the other node to start it's BER test and then starts collecting bit errors immediately. | |||
| OBJECT-TYPE | |||
| INTEGER | active(1), stopped(2), start-up(3), waiting(4), pend-active(5), bert-los(6) | ||
| hdsl2StatBertErrorCounter | 1.3.6.1.4.1.529.4.12.2.1.22 | ||
| BER test bit error counter. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| Hdsl2LineStatusEntry | |||
| SEQUENCE | |||
| INTEGER as hdsl2StatusIfEntryIndex | |||
| INTEGER as hdsl2StatusShelfIndex | |||
| INTEGER as hdsl2StatusSlotIndex | |||
| INTEGER as hdsl2StatusLineIndex | |||
| INTEGER as hdsl2StatusUnitType | |||
| INTEGER as hdsl2StatusLineState | |||
| INTEGER as hdsl2StatusOpRate | |||
| INTEGER as hdsl2StatusVendorId | |||
| INTEGER as hdsl2StatusMajorFirmWareVer | |||
| INTEGER as hdsl2StatusMinorFirmWareVer | |||
| INTEGER as hdsl2StatusHardWareVer | |||
| Hdsl2LineStatisticEntry | |||
| SEQUENCE | |||
| INTEGER as hdsl2StatIfEntryIndex | |||
| INTEGER as hdsl2StatShelfIndex | |||
| INTEGER as hdsl2StatSlotIndex | |||
| INTEGER as hdsl2StatLineIndex | |||
| INTEGER as hdsl2StatConnUpDays | |||
| INTEGER as hdsl2StatConnUpHours | |||
| INTEGER as hdsl2StatConnUpMinutes | |||
| INTEGER as hdsl2StatRxSignalPresent | |||
| INTEGER as hdsl2StatLineQualityDb | |||
| INTEGER as hdsl2StatUpDwnCntr | |||
| INTEGER as hdsl2StatLineSelfTest | |||
| INTEGER as hdsl2StatTxPower | |||
| INTEGER as hdsl2StatFramerCrcErrors | |||
| INTEGER as hdsl2StatFramerSyncStatus | |||
| INTEGER as hdsl2StatFramerLosdCnt | |||
| INTEGER as hdsl2StatFramerSegaCnt | |||
| INTEGER as hdsl2StatFramerSegdCnt | |||
| INTEGER as hdsl2StatFramerRxHecErrors | |||
| INTEGER as hdsl2StatBertTimer | |||
| INTEGER as hdsl2StatBertEna | |||
| INTEGER as hdsl2StatBertState | |||
| INTEGER as hdsl2StatBertErrorCounter | |||