ASCEND-MIBDMTALNET-MIB

File: ASCEND-MIBDMTALNET-MIB.mib (27763 bytes)

Imported modules

ASCEND-MIB RFC1155-SMI RFC-1212

Imported symbols

configuration IpAddress OBJECT-TYPE

Defined Objects

mibdmtAlDslNetworkProfile 1.3.6.1.4.1.529.23.10
OBJECT IDENTIFIER    

mibdmtAlDslNetworkProfileTable 1.3.6.1.4.1.529.23.10.1
A list of mibdmtAlDslNetworkProfile profile entries.
OBJECT-TYPE    
  SEQUENCE OF  
    MibdmtAlDslNetworkProfileEntry

mibdmtAlDslNetworkProfileEntry 1.3.6.1.4.1.529.23.10.1.1
A mibdmtAlDslNetworkProfile entry containing objects that maps to the parameters of mibdmtAlDslNetworkProfile profile.
OBJECT-TYPE    
  MibdmtAlDslNetworkProfileEntry  

dmtAlDslNetworkProfile-Shelf-o 1.3.6.1.4.1.529.23.10.1.1.1
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-Slot-o 1.3.6.1.4.1.529.23.10.1.1.2
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-Item-o 1.3.6.1.4.1.529.23.10.1.1.3
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-Name 1.3.6.1.4.1.529.23.10.1.1.4
For future use. The current design does not use the name field but instead references Cell Based Dmt Adsl lines by the physical address; we may in the future support referencing Cell Based Dmt Adsl lines by name as well as by address. The name consists of a null terminated ascii string supplied by the user; it defaults to the ascii form of the Cell Based Dmt Adsl line physical address.
OBJECT-TYPE    
  DisplayString  

dmtAlDslNetworkProfile-PhysicalAddress-Shelf 1.3.6.1.4.1.529.23.10.1.1.5
The number of the shelf that the addressed physical device resides on.
OBJECT-TYPE    
  INTEGER anyShelf(1), shelf1(2), shelf2(3), shelf3(4), shelf4(5), shelf5(6), shelf6(7), shelf7(8), shelf8(9), shelf9(10)  

dmtAlDslNetworkProfile-PhysicalAddress-Slot 1.3.6.1.4.1.529.23.10.1.1.6
The number of the slot that the addressed physical device resides on.
OBJECT-TYPE    
  INTEGER anySlot(1), slot1(2), slot2(3), slot3(4), slot4(5), slot5(6), slot6(7), slot7(8), slot8(9), slot9(10), slot10(11), slot11(12), slot12(13), slot13(14), slot14(15), slot15(16), slot16(17), slot17(18), slot18(19), slot19(20), slot20(21), slot21(22), slot22(23), slot23(24), slot24(25), slot25(26), slot26(27), slot27(28), slot28(29), slot29(30), slot30(31), slot31(32), slot32(33), slot33(34), slot34(35), slot35(36), slot36(37), slot37(38), slot38(39), slot39(40), slot40(41), aLim(55), bLim(56), cLim(57), dLim(58), leftController(49), rightController(50), controller(42), firstControlModule(53), secondControlModule(54), trunkModule1(45), trunkModule2(46), controlModule(51), slotPrimary(59)  

dmtAlDslNetworkProfile-PhysicalAddress-ItemNumber 1.3.6.1.4.1.529.23.10.1.1.7
A number that specifies an addressable entity within the context of shelf and slot.
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-Enabled 1.3.6.1.4.1.529.23.10.1.1.8
TRUE if the line is enabled, otherwise FALSE.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

dmtAlDslNetworkProfile-ProfileNumber 1.3.6.1.4.1.529.23.10.1.1.9
For potential backwards compatibility. The current design consists of one line profile numbered 0.
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-LineConfig-NailedGroup 1.3.6.1.4.1.529.23.10.1.1.11
A number that identifies the set of lines that makes up a nailed group. 0 means this line is not part of a nailed group.
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-LineConfig-RateAdaptModeUp 1.3.6.1.4.1.529.23.10.1.1.19
The up stream rate adaptive mode of operation. ONLY OPERATOR_CONTROLLED and AUTOMATIC_AT_STARTUP are currently supported.
OBJECT-TYPE    
  INTEGER operator(1), automaticAtStartup(2), dynamic(3)  

dmtAlDslNetworkProfile-LineConfig-RateAdaptModeDown 1.3.6.1.4.1.529.23.10.1.1.20
The down stream rate adaptive mode of operation. ONLY OPERATOR_CONTROLLED and AUTOMATIC_AT_STARTUP are currently supported.
OBJECT-TYPE    
  INTEGER operator(1), automaticAtStartup(2), dynamic(3)  

dmtAlDslNetworkProfile-LineConfig-RateAdaptRatioUp 1.3.6.1.4.1.529.23.10.1.1.21
The ratio in percent of excess bitrate distribution over the up stream fast and interleaved latencies. 100% - fast path , 0% - interleaved path. Valid ONLY in rate-adapt-mode = AUTOMATIC_AT_STARTUP or DYNAMIC .
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-LineConfig-RateAdaptRatioDown 1.3.6.1.4.1.529.23.10.1.1.22
The ratio in percent of excess bitrate distribution over the down stream fast and interleaved latencies. 100% - fast path , 0% - interleaved path. Valid ONLY in rate-adapt-mode = AUTOMATIC_AT_STARTUP or DYNAMIC .
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-LineConfig-MaxPowerSpectralDensity 1.3.6.1.4.1.529.23.10.1.1.25
The power spectral density in dBm/Hz allowed on the line. Decreasing the value may reduce capacity. Defined for downstream only. Actual value is negative.
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-FastPathConfig-MinBitrateUp 1.3.6.1.4.1.529.23.10.1.1.26
The up stream minimum requested bitrate, in Kbps. NOT valid in rate-adapt-mode = OPERATOR_CONTROLLED.
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-FastPathConfig-MinBitrateDown 1.3.6.1.4.1.529.23.10.1.1.27
The down stream minimum requested bitrate, in Kbps. NOT valid in rate-adapt-mode = OPERATOR_CONTROLLED.
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-FastPathConfig-MaxBitrateUp 1.3.6.1.4.1.529.23.10.1.1.28
The up stream maximum requested bitrate, in Kbps. NOT valid in rate-adapt-mode = OPERATOR_CONTROLLED.
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-FastPathConfig-MaxBitrateDown 1.3.6.1.4.1.529.23.10.1.1.29
The down stream maximum requested bitrate, in Kbps. NOT valid in rate-adapt-mode = OPERATOR_CONTROLLED.
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-FastPathConfig-PlannedBitrateUp 1.3.6.1.4.1.529.23.10.1.1.30
The up stream rate that will be used, in Kbps. ONLY valid in rate-adapt-mode = OPERATOR_CONTROLLED.
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-FastPathConfig-PlannedBitrateDown 1.3.6.1.4.1.529.23.10.1.1.31
The down stream rate that will be used, in Kbps. ONLY valid in rate-adapt-mode = OPERATOR_CONTROLLED.
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-InterleavePathConfig-MinBitrateUp 1.3.6.1.4.1.529.23.10.1.1.32
The up stream minimum requested bitrate, in Kbps. NOT valid in rate-adapt-mode = OPERATOR_CONTROLLED.
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-InterleavePathConfig-MinBitrateDown 1.3.6.1.4.1.529.23.10.1.1.33
The down stream minimum requested bitrate, in Kbps. NOT valid in rate-adapt-mode = OPERATOR_CONTROLLED.
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-InterleavePathConfig-MaxBitrateUp 1.3.6.1.4.1.529.23.10.1.1.34
The up stream maximum requested bitrate, in Kbps. NOT valid in rate-adapt-mode = OPERATOR_CONTROLLED.
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-InterleavePathConfig-MaxBitrateDown 1.3.6.1.4.1.529.23.10.1.1.35
The down stream maximum requested bitrate, in Kbps. NOT valid in rate-adapt-mode = OPERATOR_CONTROLLED.
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-InterleavePathConfig-PlannedBitrateUp 1.3.6.1.4.1.529.23.10.1.1.36
The up stream rate that will be used, in Kbps. ONLY valid in rate-adapt-mode = OPERATOR_CONTROLLED.
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-InterleavePathConfig-PlannedBitrateDown 1.3.6.1.4.1.529.23.10.1.1.37
The down stream rate that will be used, in Kbps. ONLY valid in rate-adapt-mode = OPERATOR_CONTROLLED.
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-InterleavePathConfig-MaxDelayUp 1.3.6.1.4.1.529.23.10.1.1.38
The maximum allowed up stream interleaver induced delay, in msec.
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-InterleavePathConfig-MaxDelayDown 1.3.6.1.4.1.529.23.10.1.1.39
The maximum allowed down stream interleaver induced delay, in msec.
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-MarginConfig-TargetNoiseMarginUp 1.3.6.1.4.1.529.23.10.1.1.40
The up stream noise margin in dB that the modem shall achieve relative to BER 10^-7.
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-MarginConfig-TargetNoiseMarginDown 1.3.6.1.4.1.529.23.10.1.1.41
The down stream noise margin in dB that the modem shall achieve relative to BER 10^-7.
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-MarginConfig-MinNoiseMarginUp 1.3.6.1.4.1.529.23.10.1.1.42
The up stream minimum noise margin in dB that the modem shall tolerate relative to BER 10^-7. If current noise margin falls below this level the ATU shall attempt to increase far-end output power to get margin above this limit, by means of bit swapping.
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-MarginConfig-MinNoiseMarginDown 1.3.6.1.4.1.529.23.10.1.1.43
The down stream minimum noise margin in dB that the modem shall tolerate relative to BER 10^-7. If current noise margin falls below this level the ATU shall attempt to increase far-end output power to get margin above this limit, by means of bit swapping.
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-MarginConfig-MaxAddNoiseMarginUp 1.3.6.1.4.1.529.23.10.1.1.44
The up stream maximum noise margin in dB on top of the target-noise-margin that the modem shall tolerate relative to BER 10^-7. If current noise margin is above this level the ATU shall attempt to reduce far-end output power to get margin below this limit, by means of bit swapping.
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-MarginConfig-MaxAddNoiseMarginDown 1.3.6.1.4.1.529.23.10.1.1.45
The down stream maximum noise margin in dB on top of the target-noise-margin that the modem shall tolerate relative to BER 10^-7. If current noise margin is above this level the ATU shall attempt to reduce far-end output power to get margin below this limit, by means of bit swapping.
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-MarginConfig-RaDownshiftMarginUp 1.3.6.1.4.1.529.23.10.1.1.46
Valid ONLY in rate-adapt-mode = DYNAMIC. In dB. If current up stream noise margin is below this parameter for more than ra-downshift-int-up sec, modem shall attemp to rate adapt (bitrate down).
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-MarginConfig-RaDownshiftIntUp 1.3.6.1.4.1.529.23.10.1.1.47
Valid ONLY in rate-adapt-mode = DYNAMIC. In seconds. If current up stream noise margin is below ra-downshift-margin-up for more than this, modem shall attemp to rate adapt (bitrate down).
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-MarginConfig-RaDownshiftMarginDown 1.3.6.1.4.1.529.23.10.1.1.48
Valid ONLY in rate-adapt-mode = DYNAMIC. In dB. If current down stream noise margin is below this parameter for more than ra-downshift-int-down sec, modem shall attemp to rate adapt (bitrate down).
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-MarginConfig-RaDownshiftIntDown 1.3.6.1.4.1.529.23.10.1.1.49
Valid ONLY in rate-adapt-mode = DYNAMIC. In seconds. If current down stream noise margin is below ra-downshift-margin-down for more than this, modem shall attemp to rate adapt (bitrate down).
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-MarginConfig-RaUpshiftMarginUp 1.3.6.1.4.1.529.23.10.1.1.50
Valid ONLY in rate-adapt-mode = DYNAMIC. In dB. If current up stream noise margin is above this parameter for more than ra-downshift-int-up sec, modem shall attemp to rate adapt (bitrate up).
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-MarginConfig-RaUpshiftIntUp 1.3.6.1.4.1.529.23.10.1.1.51
Valid ONLY in rate-adapt-mode = DYNAMIC. In seconds. If current up stream noise margin is above ra-downshift-margin-up for more than this, modem shall attemp to rate adapt (bitrate up).
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-MarginConfig-RaUpshiftMarginDown 1.3.6.1.4.1.529.23.10.1.1.52
Valid ONLY in rate-adapt-mode = DYNAMIC. In dB. If current down stream noise margin is above this parameter for more than ra-downshift-int-down sec, modem shall attemp to rate adapt (bitrate up).
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-MarginConfig-RaUpshiftIntDown 1.3.6.1.4.1.529.23.10.1.1.53
Valid ONLY in rate-adapt-mode = DYNAMIC. In seconds. If current down stream noise margin is above ra-downshift-margin-down for more than this, modem shall attemp to rate adapt (bitrate up).
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-Action-o 1.3.6.1.4.1.529.23.10.1.1.54
OBJECT-TYPE    
  INTEGER noAction(1), createProfile(2), deleteProfile(3)  

dmtAlDslNetworkProfile-LineConfig-VpSwitchingVpi 1.3.6.1.4.1.529.23.10.1.1.55
The Vpi to be used for the VP switching. Rest of the VPIs within valid vpi-vci-range will be used for the VC switching. Changes in this range will take effect immediately. THE USER SHOULD BE VERY CAREFUL WHILE CHANGING THIS VALUE BECAUSE ALL CONNECTIONS ON THE LIM WHERE THIS PORT BELONGS WILL BE DROPPED IN ORDER TO MAKE THIS NEW VALUE EFFECTIVE IMMEDIATELY.
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-LineConfig-MaxAggrPowerLevelUp 1.3.6.1.4.1.529.23.10.1.1.56
The maximum aggregate output power in dBm allowed on the line in the up stream direction. Increasing value may result in capacity boosting.
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-LineConfig-MaxAggrPowerLevelDown 1.3.6.1.4.1.529.23.10.1.1.57
The maximum aggregate output power in dBm allowed on the line in the down stream direction. Increasing value may result in capacity boosting.
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-LineConfig-LineCode 1.3.6.1.4.1.529.23.10.1.1.58
The DMT line code is used for the training. NOTE: for the ADSL 12-ports LIM card only (which uses the ALCATEL chipset), setting the line code to ansi-dmt will provide better line rate than auto-select for an ansi-dmt link. Therefore, set the line code to ansi-dmt for an ansi-dmt link to obtain optimal rate.
OBJECT-TYPE    
  INTEGER autoSelect(3), gLite(2), ansiDmt(4), gDmt(5), legacyMode(6), etsiAnnexB(7)  

dmtAlDslNetworkProfile-LineConfig-LineLatencyDown 1.3.6.1.4.1.529.23.10.1.1.59
The DMT line latency to be used for the downstream data transport.
OBJECT-TYPE    
  INTEGER none(1), fast(2), interleave(3), both(4)  

dmtAlDslNetworkProfile-LineConfig-LineLatencyUp 1.3.6.1.4.1.529.23.10.1.1.60
The DMT line latency to be used for the upstream data transport.
OBJECT-TYPE    
  INTEGER none(1), fast(2), interleave(3), both(4)  

dmtAlDslNetworkProfile-LineConfig-TrellisEncoding 1.3.6.1.4.1.529.23.10.1.1.61
TRUE if trellis encoding is to be enabled, FALSE otherwise.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

dmtAlDslNetworkProfile-LineConfig-GainDefault 1.3.6.1.4.1.529.23.10.1.1.62
The default gain value in db to be used for the AGC.
OBJECT-TYPE    
  INTEGER n-20Db(2), n-16Db(1)  

dmtAlDslNetworkProfile-SparingMode 1.3.6.1.4.1.529.23.10.1.1.63
Port sparing operational mode for this port.
OBJECT-TYPE    
  INTEGER inactive(1), manual(2), automatic(3)  

dmtAlDslNetworkProfile-LineConfig-UpstreamStartBin 1.3.6.1.4.1.529.23.10.1.1.64
The starting upstream frequency bin.
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-LineConfig-UpstreamEndBin 1.3.6.1.4.1.529.23.10.1.1.65
The ending upstream frequency bin.
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-LineConfig-DownstreamStartBin 1.3.6.1.4.1.529.23.10.1.1.66
The starting downstream frequency bin.
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-LineConfig-DownstreamEndBin 1.3.6.1.4.1.529.23.10.1.1.67
The ending downstream frequency bin.
OBJECT-TYPE    
  INTEGER  

dmtAlDslNetworkProfile-LineConfig-LoopBack 1.3.6.1.4.1.529.23.10.1.1.69
Configuration of different modem loopbacks.
OBJECT-TYPE    
  INTEGER none(1), analog(2), digital(3)  

dmtAlDslNetworkProfile-LineConfig-BitSwapping 1.3.6.1.4.1.529.23.10.1.1.70
Controls wether Bit-Swapping is enabled or no. On 12 port DMT card and 48 port G.lite card has not effect.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

dmtAlDslNetworkProfile-LineConfig-FbmDbmMode 1.3.6.1.4.1.529.23.10.1.1.71
Controls wether the line is in Fixed-Bit-Map or Dual-Bit-Map mode. Only relevant for Annex-C cards.
OBJECT-TYPE    
  INTEGER fbm(1), dbm(2)  

dmtAlDslNetworkProfile-ThreshProfile 1.3.6.1.4.1.529.23.10.1.1.72
The name of the DSL-THRESHOLD profile which applies to this ADSL line.
OBJECT-TYPE    
  DisplayString  

dmtAlDslNetworkProfile-IgnoreLineup 1.3.6.1.4.1.529.23.10.1.1.73
Ignore line up value for this port.
OBJECT-TYPE    
  INTEGER systemDefined(1), no(2), yes(3)  

dmtAlDslNetworkProfile-LineConfig-AlcatelUs413Boost 1.3.6.1.4.1.529.23.10.1.1.74
Provides an increase in upstream rate in T1.413 mode for 24/48 Port Annex A boards based on the Globespan chip set when connected to an Alcatel CPE. Irrelevant for any other situtation. Use with extreme caution.
OBJECT-TYPE    
  INTEGER new(1), old(2), unknown(3)  

Defined Objects

DisplayString  
OCTET STRING    

MibdmtAlDslNetworkProfileEntry  
SEQUENCE    
  INTEGER as dmtAlDslNetworkProfile-Shelf-o  
  INTEGER as dmtAlDslNetworkProfile-Slot-o  
  INTEGER as dmtAlDslNetworkProfile-Item-o  
  DisplayString as dmtAlDslNetworkProfile-Name  
  INTEGER as dmtAlDslNetworkProfile-PhysicalAddress-Shelf  
  INTEGER as dmtAlDslNetworkProfile-PhysicalAddress-Slot  
  INTEGER as dmtAlDslNetworkProfile-PhysicalAddress-ItemNumber  
  INTEGER as dmtAlDslNetworkProfile-Enabled  
  INTEGER as dmtAlDslNetworkProfile-SparingMode  
  INTEGER as dmtAlDslNetworkProfile-ProfileNumber  
  INTEGER as dmtAlDslNetworkProfile-IgnoreLineup  
  INTEGER as dmtAlDslNetworkProfile-LineConfig-NailedGroup  
  INTEGER as dmtAlDslNetworkProfile-LineConfig-VpSwitchingVpi  
  INTEGER as dmtAlDslNetworkProfile-LineConfig-RateAdaptModeUp  
  INTEGER as dmtAlDslNetworkProfile-LineConfig-RateAdaptModeDown  
  INTEGER as dmtAlDslNetworkProfile-LineConfig-RateAdaptRatioUp  
  INTEGER as dmtAlDslNetworkProfile-LineConfig-RateAdaptRatioDown  
  INTEGER as dmtAlDslNetworkProfile-LineConfig-MaxAggrPowerLevelUp  
  INTEGER as dmtAlDslNetworkProfile-LineConfig-MaxAggrPowerLevelDown  
  INTEGER as dmtAlDslNetworkProfile-LineConfig-MaxPowerSpectralDensity  
  INTEGER as dmtAlDslNetworkProfile-LineConfig-LineCode  
  INTEGER as dmtAlDslNetworkProfile-LineConfig-LineLatencyDown  
  INTEGER as dmtAlDslNetworkProfile-LineConfig-LineLatencyUp  
  INTEGER as dmtAlDslNetworkProfile-LineConfig-TrellisEncoding  
  INTEGER as dmtAlDslNetworkProfile-LineConfig-GainDefault  
  INTEGER as dmtAlDslNetworkProfile-LineConfig-UpstreamStartBin  
  INTEGER as dmtAlDslNetworkProfile-LineConfig-UpstreamEndBin  
  INTEGER as dmtAlDslNetworkProfile-LineConfig-DownstreamStartBin  
  INTEGER as dmtAlDslNetworkProfile-LineConfig-DownstreamEndBin  
  INTEGER as dmtAlDslNetworkProfile-LineConfig-LoopBack  
  INTEGER as dmtAlDslNetworkProfile-LineConfig-BitSwapping  
  INTEGER as dmtAlDslNetworkProfile-LineConfig-FbmDbmMode  
  INTEGER as dmtAlDslNetworkProfile-LineConfig-AlcatelUs413Boost  
  INTEGER as dmtAlDslNetworkProfile-FastPathConfig-MinBitrateUp  
  INTEGER as dmtAlDslNetworkProfile-FastPathConfig-MinBitrateDown  
  INTEGER as dmtAlDslNetworkProfile-FastPathConfig-MaxBitrateUp  
  INTEGER as dmtAlDslNetworkProfile-FastPathConfig-MaxBitrateDown  
  INTEGER as dmtAlDslNetworkProfile-FastPathConfig-PlannedBitrateUp  
  INTEGER as dmtAlDslNetworkProfile-FastPathConfig-PlannedBitrateDown  
  INTEGER as dmtAlDslNetworkProfile-InterleavePathConfig-MinBitrateUp  
  INTEGER as dmtAlDslNetworkProfile-InterleavePathConfig-MinBitrateDown  
  INTEGER as dmtAlDslNetworkProfile-InterleavePathConfig-MaxBitrateUp  
  INTEGER as dmtAlDslNetworkProfile-InterleavePathConfig-MaxBitrateDown  
  INTEGER as dmtAlDslNetworkProfile-InterleavePathConfig-PlannedBitrateUp  
  INTEGER as dmtAlDslNetworkProfile-InterleavePathConfig-PlannedBitrateDown  
  INTEGER as dmtAlDslNetworkProfile-InterleavePathConfig-MaxDelayUp  
  INTEGER as dmtAlDslNetworkProfile-InterleavePathConfig-MaxDelayDown  
  INTEGER as dmtAlDslNetworkProfile-MarginConfig-TargetNoiseMarginUp  
  INTEGER as dmtAlDslNetworkProfile-MarginConfig-TargetNoiseMarginDown  
  INTEGER as dmtAlDslNetworkProfile-MarginConfig-MinNoiseMarginUp  
  INTEGER as dmtAlDslNetworkProfile-MarginConfig-MinNoiseMarginDown  
  INTEGER as dmtAlDslNetworkProfile-MarginConfig-MaxAddNoiseMarginUp  
  INTEGER as dmtAlDslNetworkProfile-MarginConfig-MaxAddNoiseMarginDown  
  INTEGER as dmtAlDslNetworkProfile-MarginConfig-RaDownshiftMarginUp  
  INTEGER as dmtAlDslNetworkProfile-MarginConfig-RaDownshiftIntUp  
  INTEGER as dmtAlDslNetworkProfile-MarginConfig-RaDownshiftMarginDown  
  INTEGER as dmtAlDslNetworkProfile-MarginConfig-RaDownshiftIntDown  
  INTEGER as dmtAlDslNetworkProfile-MarginConfig-RaUpshiftMarginUp  
  INTEGER as dmtAlDslNetworkProfile-MarginConfig-RaUpshiftIntUp  
  INTEGER as dmtAlDslNetworkProfile-MarginConfig-RaUpshiftMarginDown  
  INTEGER as dmtAlDslNetworkProfile-MarginConfig-RaUpshiftIntDown  
  DisplayString as dmtAlDslNetworkProfile-ThreshProfile  
  INTEGER as dmtAlDslNetworkProfile-Action-o