ASCEND-MIBSYS1-MIB

File: ASCEND-MIBSYS1-MIB.mib (23493 bytes)

Imported modules

ASCEND-MIB RFC1155-SMI RFC-1212

Imported symbols

configuration IpAddress OBJECT-TYPE

Defined Objects

mibsystemProfile 1.3.6.1.4.1.529.23.125
OBJECT IDENTIFIER    

mibsystemProfileTable 1.3.6.1.4.1.529.23.125.1
A list of mibsystemProfile profile entries.
OBJECT-TYPE    
  SEQUENCE OF  
    MibsystemProfileEntry

mibsystemProfileEntry 1.3.6.1.4.1.529.23.125.1.1
A mibsystemProfile entry containing objects that maps to the parameters of mibsystemProfile profile.
OBJECT-TYPE    
  MibsystemProfileEntry  

systemProfile-Index-o 1.3.6.1.4.1.529.23.125.1.1.1
OBJECT-TYPE    
  INTEGER  

systemProfile-Name 1.3.6.1.4.1.529.23.125.1.1.2
The name of the system given by the user, a standard null terminated ASCII string.
OBJECT-TYPE    
  DisplayString  

systemProfile-Contact 1.3.6.1.4.1.529.23.125.1.1.3
The name of the contact for this device. SNMP readable.
OBJECT-TYPE    
  DisplayString  

systemProfile-Location 1.3.6.1.4.1.529.23.125.1.1.4
The location of this device. SNMP readable.
OBJECT-TYPE    
  DisplayString  

systemProfile-TermRate 1.3.6.1.4.1.529.23.125.1.1.5
The bit rate of the management terminal port, as given above.
OBJECT-TYPE    
  INTEGER n-300Bps(1), n-1200Bps(2), n-2400Bps(3), n-4800Bps(4), n-9600Bps(5), n-19200Bps(6), n-38400Bps(7), n-57600Bps(8), n-115200Bps(9)  

systemProfile-Console 1.3.6.1.4.1.529.23.125.1.1.6
A MenuType specifying the type of interface to use on the console port.
OBJECT-TYPE    
  INTEGER standard(1), limited(2), mif(3)  

systemProfile-ConsoleSecurity 1.3.6.1.4.1.529.23.125.1.1.7
Serial console security for the control port.
OBJECT-TYPE    
  INTEGER consoleSecurityNone(1), consoleSecurityProfile(2), consoleSecurityAuthSetting(3)  

systemProfile-SystemRmtMgmt 1.3.6.1.4.1.529.23.125.1.1.8
Set true if this system allows remote management.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

systemProfile-SubAddressMode 1.3.6.1.4.1.529.23.125.1.1.9
Selects system wide sub-address support. See mibglob.mdf for details.
OBJECT-TYPE    
  INTEGER noSubaddress(1), routingSubaddress(2), termselSubaddress(3)  

systemProfile-SerialSubaddress 1.3.6.1.4.1.529.23.125.1.1.10
sub-address assigned to serial port connections.
OBJECT-TYPE    
  INTEGER  

systemProfile-LanSubaddress 1.3.6.1.4.1.529.23.125.1.1.11
sub-address assigned to sync lan connections.
OBJECT-TYPE    
  INTEGER  

systemProfile-DmSubaddress 1.3.6.1.4.1.529.23.125.1.1.12
sub-address assigned to digital modem connections.
OBJECT-TYPE    
  INTEGER  

systemProfile-V110Subaddress 1.3.6.1.4.1.529.23.125.1.1.13
sub-address assigned to V.110 rate adaption connections
OBJECT-TYPE    
  INTEGER  

systemProfile-UseTrunkGroups 1.3.6.1.4.1.529.23.125.1.1.14
Enables TrunkGroups for all network lines.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

systemProfile-NumDigitsTrunkGroups 1.3.6.1.4.1.529.23.125.1.1.15
Specify number of digits TrunkGroups support.
OBJECT-TYPE    
  INTEGER  

systemProfile-AutoLogout 1.3.6.1.4.1.529.23.125.1.1.16
When TRUE select the default security profile on loss of CD/DTR from the main console port.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

systemProfile-IdleLogout 1.3.6.1.4.1.529.23.125.1.1.17
When non-zero select the default security profile after this value of minutes with no keyboard activity.
OBJECT-TYPE    
  INTEGER  

systemProfile-P50SwitchUsage 1.3.6.1.4.1.529.23.125.1.1.18
What the P50 switch does.
OBJECT-TYPE    
  INTEGER switchUnused(1), switchSerialWan(2), switchNumberOfUses(3)  

systemProfile-oDS0MinRst 1.3.6.1.4.1.529.23.125.1.1.19
Has three choices: Off, 24Hr or Monthly. When enabled, the following maxSystemDS0Mins is the high water mark at which all switched connections originating on the system will be taken down.
OBJECT-TYPE    
  INTEGER off(1), daily(2), monthly(3)  

systemProfile-MaxSystemDS0Mins 1.3.6.1.4.1.529.23.125.1.1.20
Sets the high water billing mark at which all originating switched connections are brought down.
OBJECT-TYPE    
  INTEGER  

systemProfile-MaxDialoutTime 1.3.6.1.4.1.529.23.125.1.1.21
The max time in Sec, system will wait for Call Setup Complete
OBJECT-TYPE    
  INTEGER  

systemProfile-ParallelDialing 1.3.6.1.4.1.529.23.125.1.1.22
The number of simultaneous DS0 channel outdials the switch allows.
OBJECT-TYPE    
  INTEGER  

systemProfile-SingleFileIncoming 1.3.6.1.4.1.529.23.125.1.1.23
Should the calls be treated as a single-file list, or in parallel. PictureTel wants parallel others want single-file.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

systemProfile-DelayDualPortDialing 1.3.6.1.4.1.529.23.125.1.1.24
TRUE if we should delay between dual port calls, FALSE if they should be placed at the same time.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

systemProfile-EditNumber 1.3.6.1.4.1.529.23.125.1.1.25
The menu number of the default edit screen.
OBJECT-TYPE    
  DisplayString  

systemProfile-AnalogEncoding 1.3.6.1.4.1.529.23.125.1.1.26
Sets the encoding standard for digitized analog data to either u-Law or A-Law. Universally sets all codecs on the unit to the value selected. Defaults to u-Law for T1, A-Law for E1 interfaces.
OBJECT-TYPE    
  INTEGER uLaw(1), aLaw(2)  

systemProfile-SessionidBase 1.3.6.1.4.1.529.23.125.1.1.27
The base session ID value
OBJECT-TYPE    
  INTEGER  

systemProfile-TOnline 1.3.6.1.4.1.529.23.125.1.1.28
TRUE if we should route calls to T-Online, FALSE if not.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

systemProfile-TOnlineMostAvailChan 1.3.6.1.4.1.529.23.125.1.1.29
TRUE if T-Online calls are to be routed to NT line with the most available B-channels FALSE if it is based on circular basis.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

systemProfile-T302Timer 1.3.6.1.4.1.529.23.125.1.1.30
Number of milliseconds to wait for additional called number information elements for an incoming T-Online call. Defaults to 1500.
OBJECT-TYPE    
  INTEGER  

systemProfile-CallRoutingSortMethod 1.3.6.1.4.1.529.23.125.1.1.31
How to sort the Call Routing table for analog calls.
OBJECT-TYPE    
  INTEGER itemFirst(1), slotFirst(2)  

systemProfile-DigitalCallRoutingSortMethod 1.3.6.1.4.1.529.23.125.1.1.32
How to sort the Call Routing table for digital calls.
OBJECT-TYPE    
  INTEGER itemFirst(1), slotFirst(2)  

systemProfile-ExactMatchCallRouting 1.3.6.1.4.1.529.23.125.1.1.33
If yes, the system will search for an exact match of call-route profile parameters when selecting devices. Wildcard matches will be accepted only after all 4 quadrants have been searched. (APX only)
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

systemProfile-ShelfControllerType 1.3.6.1.4.1.529.23.125.1.1.34
Used to define the role of this controller in a single-shelf or multi-shelf system. Note: This variable is not applicable to the APX 8000.
OBJECT-TYPE    
  INTEGER standalone(1), master(2), slave(3)  

systemProfile-MasterShelfController 1.3.6.1.4.1.529.23.125.1.1.35
Master shelf controller number. This attribute exists only when the shelf-controller-type is SLAVE. Note: This variable is not applicable to the APX 8000.
OBJECT-TYPE    
  INTEGER  

systemProfile-NewNasPortIdFormat 1.3.6.1.4.1.529.23.125.1.1.36
Field is deprecated; use the 'nas-port-format' field to specify the NAS port format. Will be used only if 'nas-port-format' is set to 'not-applicable'. TRUE if new NAS port ID format is used, FALSE if old NAS Port ID is used. On the TNT product family the new NAS port ID format is used by default. The old format cannot be used for multi-shelf systems or if any line cards are in a slot greater than the twelfth position.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

systemProfile-ModemPriTypeOfNumber 1.3.6.1.4.1.529.23.125.1.1.37
PRI Called Party element's Type-Of-Number value for outgoing modem calls.
OBJECT-TYPE    
  INTEGER  

systemProfile-ModemPriNumberingPlanId 1.3.6.1.4.1.529.23.125.1.1.38
PRI Called Party element's Numbering-Plan-ID value for outgoing modem calls.
OBJECT-TYPE    
  INTEGER  

systemProfile-WanInterface 1.3.6.1.4.1.529.23.125.1.1.39
Sets the type of WAN interface supported: T1-CSU or Serial WAN.
OBJECT-TYPE    
  INTEGER wanT1(1), wanSwan(2)  

systemProfile-PermConnUpdMode 1.3.6.1.4.1.529.23.125.1.1.40
Enables nonintrusive remote update of permanent connections' configurations. 'Changed' means that only changed connections will be torn down and reestablished, 'All' means all existing permanent connections will be turn down and then reestablished only if they are fetched from the RADIUS server again
OBJECT-TYPE    
  INTEGER all(1), changed(2)  

systemProfile-UserstatFormat 1.3.6.1.4.1.529.23.125.1.1.41
Defines the output format of the session listing command 'userstat' and the remote user information protocol 'finger'. The following special characters will be converted to their values for each listed session. The width of each field is indicated in []. %i [10] SessionID, Unique ID assigned to the session. %l [10] Line/Chan, Physical address (shelf.slot.line/chan). %s [11] Slot:Item, shelf:slot:item/logical-item of the host port. %r [11] Tx/Rx Rate, Transmit and receive rates. %d [ 3] Svc, A three-letter code showing the type of service. %a [15] Address, IP address. %u [14] Username, Connection profile name. %c [10] ConnTime, Ammount of time connected in hours:minutes:seconds. %t [10] IdleTime, Ammount of time idle in hours:minutes:seconds. %n [24] Dialed#, Number dialed if known. %f [24] Calling#, Number calling from if known. For example set userstat-format = '%i %l %s %r %d %a %u %c %t %n' would set the format to the factory default value.
OBJECT-TYPE    
  DisplayString  

systemProfile-ControlBusType 1.3.6.1.4.1.529.23.125.1.1.42
How to send control bus messages. This attribute exists only when the shelf-controller-type is not SLAVE.
OBJECT-TYPE    
  INTEGER dpram(1), pbus(2)  

systemProfile-BootSrVersion 1.3.6.1.4.1.529.23.125.1.1.43
Place for tntsrb, the shelf controller boot loader, to provide its version. Boot loader updates the field with its version on every system reset
OBJECT-TYPE    
  DisplayString  

systemProfile-SysModemProfile-oATAnswerString 1.3.6.1.4.1.529.23.125.1.1.44
Allows the user to enter any additional AT commands in the modem answer string.
OBJECT-TYPE    
  DisplayString  

systemProfile-CallByCall 1.3.6.1.4.1.529.23.125.1.1.45
PRI Called Party element's Network Specific Facility for Call-by-Call.
OBJECT-TYPE    
  INTEGER  

systemProfile-Country 1.3.6.1.4.1.529.23.125.1.1.46
Country in which the system is located.
OBJECT-TYPE    
  INTEGER argentina(2), australia(3), belgium(4), brazil(23), china(5), costaRica(6), finland(7), france(8), germany(9), hongKong(10), italy(11), japan(12), korea(13), mexico(14), netherlands(15), newZealand(16), singapore(17), spain(18), sweden(19), switzerland(20), uk(21), us(22)  

systemProfile-PotsDigitTimeout 1.3.6.1.4.1.529.23.125.1.1.47
POTS interdigit timeout.
OBJECT-TYPE    
  INTEGER  

systemProfile-System8kClock 1.3.6.1.4.1.529.23.125.1.1.48
8KHz clock source for Stinger-10.
OBJECT-TYPE    
  INTEGER controller(2), limOrTrunkModule(3), bits(4), ami8k(5)  

systemProfile-SupportDbcs 1.3.6.1.4.1.529.23.125.1.1.49
TRUE if we should support DBCS character set, FALSE if not.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

systemProfile-IncCallDistrib 1.3.6.1.4.1.529.23.125.1.1.50
Route incoming calls to first available valid port or the least used among a set of ports.
OBJECT-TYPE    
  INTEGER firstAvailable(2), fairShare(3)  

systemProfile-IgnoreLineup 1.3.6.1.4.1.529.23.125.1.1.51
If ignore-lineup in line config profile is set to SYSTEM DEFINED, then this will take precedence.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

systemProfile-Action-o 1.3.6.1.4.1.529.23.125.1.1.52
OBJECT-TYPE    
  INTEGER noAction(1), createProfile(2), deleteProfile(3)  

systemProfile-JamFileComponents-JamFile1 1.3.6.1.4.1.529.23.125.1.1.53
File name of the first JAM file's component
OBJECT-TYPE    
  DisplayString  

systemProfile-JamFileComponents-JamFile2 1.3.6.1.4.1.529.23.125.1.1.54
File name of the second JAM file's component
OBJECT-TYPE    
  DisplayString  

systemProfile-JamFileComponents-JamFile3 1.3.6.1.4.1.529.23.125.1.1.55
File name of the third JAM file's component
OBJECT-TYPE    
  DisplayString  

systemProfile-JamFileComponents-JamFile4 1.3.6.1.4.1.529.23.125.1.1.56
File name of the fourth JAM file's component
OBJECT-TYPE    
  DisplayString  

systemProfile-JamFileComponents-JamFile5 1.3.6.1.4.1.529.23.125.1.1.57
File name of the fifth JAM file's component
OBJECT-TYPE    
  DisplayString  

systemProfile-JamFileComponents-JamFile6 1.3.6.1.4.1.529.23.125.1.1.58
File name of the sixth JAM file's component
OBJECT-TYPE    
  DisplayString  

systemProfile-NasPortFormat 1.3.6.1.4.1.529.23.125.1.1.59
Specifies NAS-Port-Format used to calculate the NAS-Port-ID. When set to 'not-applicable', indicates that the NAS Port Format is determined by the settings in the 'new-nas-port-id-format' field. Defaults to 'not-applicable'.
OBJECT-TYPE    
  INTEGER notApplicable(1), n-2455(2), n-655(3), n-122(4), n-1233(5)  

mibsystemProfile-StatusNumberTable 1.3.6.1.4.1.529.23.125.2
A list of mibsystemProfile__status_number profile entries.
OBJECT-TYPE    
  SEQUENCE OF  
    MibsystemProfile-StatusNumberEntry

mibsystemProfile-StatusNumberEntry 1.3.6.1.4.1.529.23.125.2.1
A mibsystemProfile__status_number entry containing objects that maps to the parameters of mibsystemProfile__status_number profile.
OBJECT-TYPE    
  MibsystemProfile-StatusNumberEntry  

systemProfile-StatusNumber-Index-o 1.3.6.1.4.1.529.23.125.2.1.1
OBJECT-TYPE    
  INTEGER  

systemProfile-StatusNumber-Index1-o 1.3.6.1.4.1.529.23.125.2.1.2
OBJECT-TYPE    
  INTEGER  

systemProfile-StatusNumber 1.3.6.1.4.1.529.23.125.2.1.3
An array of status screen number entries used to specify the default status screen layout.
OBJECT-TYPE    
  DisplayString  

Defined Objects

DisplayString  
OCTET STRING    

MibsystemProfileEntry  
SEQUENCE    
  INTEGER as systemProfile-Index-o  
  DisplayString as systemProfile-Name  
  DisplayString as systemProfile-Contact  
  DisplayString as systemProfile-Location  
  INTEGER as systemProfile-TermRate  
  INTEGER as systemProfile-Console  
  INTEGER as systemProfile-ConsoleSecurity  
  INTEGER as systemProfile-SystemRmtMgmt  
  INTEGER as systemProfile-SubAddressMode  
  INTEGER as systemProfile-SerialSubaddress  
  INTEGER as systemProfile-LanSubaddress  
  INTEGER as systemProfile-DmSubaddress  
  INTEGER as systemProfile-V110Subaddress  
  INTEGER as systemProfile-UseTrunkGroups  
  INTEGER as systemProfile-NumDigitsTrunkGroups  
  INTEGER as systemProfile-AutoLogout  
  INTEGER as systemProfile-IdleLogout  
  INTEGER as systemProfile-P50SwitchUsage  
  INTEGER as systemProfile-oDS0MinRst  
  INTEGER as systemProfile-MaxSystemDS0Mins  
  INTEGER as systemProfile-MaxDialoutTime  
  INTEGER as systemProfile-ParallelDialing  
  INTEGER as systemProfile-SingleFileIncoming  
  INTEGER as systemProfile-DelayDualPortDialing  
  DisplayString as systemProfile-EditNumber  
  INTEGER as systemProfile-AnalogEncoding  
  INTEGER as systemProfile-SessionidBase  
  INTEGER as systemProfile-TOnline  
  INTEGER as systemProfile-TOnlineMostAvailChan  
  INTEGER as systemProfile-T302Timer  
  INTEGER as systemProfile-CallRoutingSortMethod  
  INTEGER as systemProfile-DigitalCallRoutingSortMethod  
  INTEGER as systemProfile-ExactMatchCallRouting  
  INTEGER as systemProfile-ShelfControllerType  
  INTEGER as systemProfile-MasterShelfController  
  INTEGER as systemProfile-NewNasPortIdFormat  
  INTEGER as systemProfile-NasPortFormat  
  INTEGER as systemProfile-ModemPriTypeOfNumber  
  INTEGER as systemProfile-ModemPriNumberingPlanId  
  INTEGER as systemProfile-WanInterface  
  INTEGER as systemProfile-PermConnUpdMode  
  DisplayString as systemProfile-UserstatFormat  
  INTEGER as systemProfile-ControlBusType  
  DisplayString as systemProfile-BootSrVersion  
  DisplayString as systemProfile-SysModemProfile-oATAnswerString  
  INTEGER as systemProfile-CallByCall  
  INTEGER as systemProfile-Country  
  INTEGER as systemProfile-PotsDigitTimeout  
  INTEGER as systemProfile-System8kClock  
  INTEGER as systemProfile-SupportDbcs  
  INTEGER as systemProfile-IncCallDistrib  
  INTEGER as systemProfile-IgnoreLineup  
  DisplayString as systemProfile-JamFileComponents-JamFile1  
  DisplayString as systemProfile-JamFileComponents-JamFile2  
  DisplayString as systemProfile-JamFileComponents-JamFile3  
  DisplayString as systemProfile-JamFileComponents-JamFile4  
  DisplayString as systemProfile-JamFileComponents-JamFile5  
  DisplayString as systemProfile-JamFileComponents-JamFile6  
  INTEGER as systemProfile-Action-o  

MibsystemProfile-StatusNumberEntry  
SEQUENCE    
  INTEGER as systemProfile-StatusNumber-Index-o  
  INTEGER as systemProfile-StatusNumber-Index1-o  
  DisplayString as systemProfile-StatusNumber