
| ASCEND-WAN-MIB | RFC-1212 |
| wanTypeSdsl | OBJECT-TYPE |
| sdslLineStatusTable | 1.3.6.1.4.1.529.4.8.1 | ||
| SDSL status parameters. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SdslLineStatusEntry | |||
| sdslLineStatusEntry | 1.3.6.1.4.1.529.4.8.1.1 | ||
| An interface status entry containing objects to describe the interface. | |||
| OBJECT-TYPE | |||
| SdslLineStatusEntry | |||
| sdslStatusIfEntryIndex | 1.3.6.1.4.1.529.4.8.1.1.1 | ||
| Interface group index assigned to this port. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| sdslStatusShelfIndex | 1.3.6.1.4.1.529.4.8.1.1.2 | ||
| TNT's SDSL modules Shelf ID. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| sdslStatusSlotIndex | 1.3.6.1.4.1.529.4.8.1.1.3 | ||
| TNT's SDSL modules Slot ID. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| sdslStatusLineIndex | 1.3.6.1.4.1.529.4.8.1.1.4 | ||
| SDSL modules line ID. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| sdslStatusUnitType | 1.3.6.1.4.1.529.4.8.1.1.5 | ||
| Unit type defines if the unit is operating either as a Central Office Equipment (COE) or Customer Premiss equipment (CPE). | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), coe(2), cpe(3) | ||
| sdslStatusLineState | 1.3.6.1.4.1.529.4.8.1.1.6 | ||
| Interface state describes the current ports operating state. States are: Config, Pend Down, Up, Down, Start-up, or N/A. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), configure(2), deactivate(3), deactive-lost(4), start-up(5), pend-port-up(6), up(7), pend-deactivate(8), out-of-service(9) | ||
| sdslStatusUpRate | 1.3.6.1.4.1.529.4.8.1.1.7 | ||
| The current up stream (cpe to coe) rate The object dslStatusUpRate is deprecated. To set line rate the object sdslConfigLineRate of the new sdslLineConfigTable should be used. | |||
| OBJECT-TYPE | |||
| INTEGER | m2320000(2320000), m1568000(1568000), m1552000(1552000), m1536000(1536000), m1168000(1168000), m1152000(1152000), m1040000(1040000), k784000(784000), k768000(768000), k528000(528000), k416000(416000), k400000(400000), k384000(384000), k272000(272000), k208000(208000), k192000(192000), k160000(160000), k144000(144000) | ||
| sdslStatusDownRate | 1.3.6.1.4.1.529.4.8.1.1.8 | ||
| The current down stream (coe to cpe) rate The object dslStatusDownRate is deprecated. To set line rate the object sdslConfigLineRate of the new sdslLineConfigTable should be used. | |||
| OBJECT-TYPE | |||
| INTEGER | m2320000(2320000), m1568000(1568000), m1552000(1552000), m1536000(1536000), m1168000(1168000), m1152000(1152000), m1040000(1040000), k784000(784000), k768000(768000), k528000(528000), k416000(416000), k400000(400000), k384000(384000), k272000(272000), k208000(208000), k192000(192000), k160000(160000), k144000(144000) | ||
| sdslStatusVendorId | 1.3.6.1.4.1.529.4.8.1.1.9 | ||
| Vendor identification. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| sdslStatusMajorFirmWareVer | 1.3.6.1.4.1.529.4.8.1.1.10 | ||
| Major firmware version. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| sdslStatusMinorFirmWareVer | 1.3.6.1.4.1.529.4.8.1.1.11 | ||
| Minor firmware version. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| sdslStatusHardWareVer | 1.3.6.1.4.1.529.4.8.1.1.12 | ||
| Hardware version. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| sdslStatusLineRate | 1.3.6.1.4.1.529.4.8.1.1.13 | ||
| The current line rate | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), m2320000(2320000), m1568000(1568000), m1552000(1552000), m1536000(1536000), m1168000(1168000), m1152000(1152000), m1040000(1040000), k784000(784000), k768000(768000), k528000(528000), k416000(416000), k400000(400000), k384000(384000), k272000(272000), k208000(208000), k192000(192000), k160000(160000), k144000(144000) | ||
| sdslLineStatisticTable | 1.3.6.1.4.1.529.4.8.2 | ||
| SDSL statistical parameters. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SdslLineStatisticEntry | |||
| sdslLineStatisticEntry | 1.3.6.1.4.1.529.4.8.2.1 | ||
| An interface statistical entry containing objects to describe the interface. | |||
| OBJECT-TYPE | |||
| SdslLineStatisticEntry | |||
| sdslStatIfEntryIndex | 1.3.6.1.4.1.529.4.8.2.1.1 | ||
| The interface groups interface index is used to index into this table. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| sdslStatShelfIndex | 1.3.6.1.4.1.529.4.8.2.1.2 | ||
| SDSL modules Shelf ID. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| sdslStatSlotIndex | 1.3.6.1.4.1.529.4.8.2.1.3 | ||
| SDSL modules Slot ID. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| sdslStatLineIndex | 1.3.6.1.4.1.529.4.8.2.1.4 | ||
| SDSL modules interface ID. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| sdslStatConnUpDays | 1.3.6.1.4.1.529.4.8.2.1.5 | ||
| Connection up day count. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| sdslStatConnUpHours | 1.3.6.1.4.1.529.4.8.2.1.6 | ||
| Connection Up 24 hour count. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| sdslStatConnUpMinutes | 1.3.6.1.4.1.529.4.8.2.1.7 | ||
| Connection up minute count. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| sdslStatRxSignalPresent | 1.3.6.1.4.1.529.4.8.2.1.8 | ||
| Receive signal present detection. | |||
| OBJECT-TYPE | |||
| INTEGER | no(1), yes(2) | ||
| sdslStatLineQualityDb | 1.3.6.1.4.1.529.4.8.2.1.9 | ||
| Lines noise margin. Reliable data will transfer with a reading of -5db or greater. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| sdslStatUpDwnCntr | 1.3.6.1.4.1.529.4.8.2.1.10 | ||
| Line Up Down counter value displays the number of times the interface transitions from a down to up state. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| sdslStatLineSelfTest | 1.3.6.1.4.1.529.4.8.2.1.11 | ||
| Line hardware self test results (Passed or Failed). | |||
| OBJECT-TYPE | |||
| INTEGER | other(4), selfTestFailed(1), localLoopBackFailed(2), passed(3) | ||
| sdslStatBertTimer | 1.3.6.1.4.1.529.4.8.2.1.12 | ||
| BER test duration configuration. The BER test lasts for the duration of this timer. | |||
| OBJECT-TYPE | |||
| INTEGER | one-minute(1), two-minutes(2), three-minutes(3), four-minutes(4), five-minutes(5), ten-minutes(6), fifteen-minutes(7), twenty-minutes(8), thirty-minutes(9) | ||
| sdslStatBertEna | 1.3.6.1.4.1.529.4.8.2.1.13 | ||
| Enable/disable of the BER test. If nodes are connected, then the BER test is ran between the units. If this node is not connected to a remote node, then the interface is placed into analog loopback and the BER test is started. | |||
| OBJECT-TYPE | |||
| INTEGER | no(1), yes(2) | ||
| sdslStatBertState | 1.3.6.1.4.1.529.4.8.2.1.14 | ||
| BER test states. When this node is not connected to another node, the test is disabled. When two nodes are connected then the BER test waits for the other node to start it's BER test and then starts collecting bit errors immediately. | |||
| OBJECT-TYPE | |||
| INTEGER | active(1), stopped(2), start-up(3), waiting(4), pend-active(5), bert-los(6) | ||
| sdslStatBertErrorCounter | 1.3.6.1.4.1.529.4.8.2.1.15 | ||
| BER test bit error counter. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| sdslLineConfigTable | 1.3.6.1.4.1.529.4.8.3 | ||
| SDSL status parameters. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SdslLineConfigEntry | |||
| sdslLineConfigEntry | 1.3.6.1.4.1.529.4.8.3.1 | ||
| An interface status entry containing objects to describe the interface. | |||
| OBJECT-TYPE | |||
| SdslLineConfigEntry | |||
| sdslConfigIfEntryIndex | 1.3.6.1.4.1.529.4.8.3.1.1 | ||
| Interface group index assigned to this port. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| sdslConfigShelfIndex | 1.3.6.1.4.1.529.4.8.3.1.2 | ||
| TNT's SDSL modules Shelf ID. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| sdslConfigSlotIndex | 1.3.6.1.4.1.529.4.8.3.1.3 | ||
| TNT's SDSL modules Slot ID. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| sdslConfigLineIndex | 1.3.6.1.4.1.529.4.8.3.1.4 | ||
| SDSL modules line ID. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| sdslConfigLineRate | 1.3.6.1.4.1.529.4.8.3.1.5 | ||
| The current line rate | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), m2320000(2320000), m1568000(1568000), m1552000(1552000), m1536000(1536000), m1168000(1168000), m1152000(1152000), m1040000(1040000), k784000(784000), k768000(768000), k528000(528000), k416000(416000), k400000(400000), k384000(384000), k272000(272000), k208000(208000), k192000(192000), k160000(160000), k144000(144000) | ||
| SdslLineStatusEntry | |||
| SEQUENCE | |||
| INTEGER as sdslStatusIfEntryIndex | |||
| INTEGER as sdslStatusShelfIndex | |||
| INTEGER as sdslStatusSlotIndex | |||
| INTEGER as sdslStatusLineIndex | |||
| INTEGER as sdslStatusUnitType | |||
| INTEGER as sdslStatusLineState | |||
| INTEGER as sdslStatusUpRate | |||
| INTEGER as sdslStatusDownRate | |||
| INTEGER as sdslStatusVendorId | |||
| INTEGER as sdslStatusMajorFirmWareVer | |||
| INTEGER as sdslStatusMinorFirmWareVer | |||
| INTEGER as sdslStatusHardWareVer | |||
| INTEGER as sdslStatusLineRate | |||
| SdslLineStatisticEntry | |||
| SEQUENCE | |||
| INTEGER as sdslStatIfEntryIndex | |||
| INTEGER as sdslStatShelfIndex | |||
| INTEGER as sdslStatSlotIndex | |||
| INTEGER as sdslStatLineIndex | |||
| INTEGER as sdslStatConnUpDays | |||
| INTEGER as sdslStatConnUpHours | |||
| INTEGER as sdslStatConnUpMinutes | |||
| INTEGER as sdslStatRxSignalPresent | |||
| INTEGER as sdslStatLineQualityDb | |||
| INTEGER as sdslStatUpDwnCntr | |||
| INTEGER as sdslStatLineSelfTest | |||
| INTEGER as sdslStatBertTimer | |||
| INTEGER as sdslStatBertEna | |||
| INTEGER as sdslStatBertState | |||
| INTEGER as sdslStatBertErrorCounter | |||
| SdslLineConfigEntry | |||
| SEQUENCE | |||
| INTEGER as sdslConfigIfEntryIndex | |||
| INTEGER as sdslConfigShelfIndex | |||
| INTEGER as sdslConfigSlotIndex | |||
| INTEGER as sdslConfigLineIndex | |||
| INTEGER as sdslConfigLineRate | |||