AT-DS3-MIB

File: AT-DS3-MIB.mib (4494 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC IF-MIB
AT-SMI-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
DisplayString TruthValue ifIndex
modules DisplayStringUnsized

Defined Objects

ds3 1.3.6.1.4.1.207.8.4.4.4.109
This MIB file contains definitions of managed objects for the DS3 module.
MODULE-IDENTITY    

ds3Traps 1.3.6.1.4.1.207.8.4.4.4.109.0
OBJECT IDENTIFIER    

tcaTrap 1.3.6.1.4.1.207.8.4.4.4.109.0.1
A DS3 trap is generated when a threshold crossing alert occurs. This happens when an error count exceeds a pre determined value. The values are counted over 15 minute and 24 hour periods. Once a trap has occured in a given period it may not occur again within the same period.
NOTIFICATION-TYPE    
  ds3TrapError  
  ds3TrapLoc  
  ds3TrapInterval  

ds3TrapTable 1.3.6.1.4.1.207.8.4.4.4.109.1
The ATR enterprise DS3 trap table.
OBJECT-TYPE    
  SEQUENCE OF  
    Ds3TrapEntry

ds3TrapEntry 1.3.6.1.4.1.207.8.4.4.4.109.1.1
An entry in the ATR enterprise DS3 trap table.
OBJECT-TYPE    
  Ds3TrapEntry  

ds3TcaTrapEnable 1.3.6.1.4.1.207.8.4.4.4.109.1.1.1
Indicates whether the threshold crossing alert traps should be generated for this interface.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

ds3TrapError 1.3.6.1.4.1.207.8.4.4.4.109.1.1.2
This variable shows which kind of parameter or primitive caused the trap. This variable is really just a placeholder for the object sent in the DS3 TRAP, but can be read independently if required. The variable will hold the value at the latest trap. A value of ds3NoError shows no trap has occured
OBJECT-TYPE    
  INTEGER ds3NoError(1), ds3PES(2), ds3PSES(3), ds3SEFs(4), ds3UAS(5), ds3LCVs(6), ds3PCVs(7), ds3LESs(8), ds3CCVs(9), ds3CESs(10), ds3CSESs(11)  

ds3TrapLoc 1.3.6.1.4.1.207.8.4.4.4.109.1.1.3
This variable shows whether the trap was caused by a problem at the local or remote end. This variable is really just a placeholder for the object sent in the DS3 TRAP, but can be read independently if required. The variable will hold the value at the latest trap. A value of ds3NoLoc shows no trap had occured.
OBJECT-TYPE    
  INTEGER ds3NoLoc(1), ds3Near(2), ds3Far(3)  

ds3TrapInterval 1.3.6.1.4.1.207.8.4.4.4.109.1.1.4
This variable shows whether the counter which has crossed the threshold is a twenty four hour or fifteen minute counter. This variable is really just a placeholder for the object sent in the DS3 TRAP, but can be read independently if required. The variable will hold the value at the latest trap. A value of ds3NoInt shows no trap has occured.
OBJECT-TYPE    
  INTEGER ds3NoInt(1), ds3Fifteen(2), ds3Twentyfour(3)  

Defined Objects

Ds3TrapEntry  
SEQUENCE    
  INTEGER as ds3TcaTrapEnable  
  INTEGER as ds3TrapError  
  INTEGER as ds3TrapLoc  
  INTEGER as ds3TrapInterval