
| RFC1155-SMI | RFC1213-MIB | RFC-1215 |
| SNMP-REPEATER-MIB |
| IpAddress | enterprises | Counter |
| OBJECT-TYPE | DisplayString | TRAP-TYPE |
| rptrAddrTrackNewLastSrcAddress |
| alliedTelesyn | 1.3.6.1.4.1.207 | ||
| OBJECT IDENTIFIER | |||
| products | 1.3.6.1.4.1.207.1 | ||
| OBJECT IDENTIFIER | |||
| bridge | 1.3.6.1.4.1.207.1.1 | ||
| OBJECT IDENTIFIER | |||
| repeater | 1.3.6.1.4.1.207.1.2 | ||
| OBJECT IDENTIFIER | |||
| hub3600 | 1.3.6.1.4.1.207.1.2.1 | ||
| OBJECT IDENTIFIER | |||
| hub3100 | 1.3.6.1.4.1.207.1.2.10 | ||
| OBJECT IDENTIFIER | |||
| intruderProtectionTrap | 1.3.6.1.4.1.207.1.2.20 | ||
| This trap is replaced by atiIntruderProtectionTrap starting from firmware ver 3.0. AT-3100 and TurboStack product families only. This trap is sent when an Intruder Alert occurs on a port due to a received packet with an unauthorized source MAC address. Intruder Protection for the module must be enabled. The varBind list contains the MAC address of the intruder. | |||
| TRAP-TYPE | |||
| rptrAddrTrackNewLastSrcAddress | |||
| atiIntruderProtectionTrap | 1.3.6.1.4.1.207.1.2.21 | ||
| AT-3100 and TurboStack product families only. This trap is sent when an Intruder Alert occurs on a module/port due to a received packet with an unauthorized source MAC address. Intruder Protection for the module must be enabled. The varBind list contains the module number, port number, and the MAC address of the intruder. | |||
| TRAP-TYPE | |||
| atiTrapIntruderModuleNumber | |||
| atiTrapIntruderPortNumber | |||
| atiTrapIntruderMacAddress | |||
| atiRedundantPortChangeTrap | 1.3.6.1.4.1.207.1.2.22 | ||
| TurboStack product family only. This trap is sent when ports, which are configured for redundant links, change from primary to secondary or secondary to primary. | |||
| TRAP-TYPE | |||
| atiPortGroupIndex | |||
| atiPortIndex | |||
| portRedundantPort | |||
| atiPortChangeDirection | |||
| hubTurboStack | 1.3.6.1.4.1.207.1.2.65 | ||
| OBJECT IDENTIFIER | |||
| mibObject | 1.3.6.1.4.1.207.8 | ||
| OBJECT IDENTIFIER | |||
| hubMib | 1.3.6.1.4.1.207.8.1 | ||
| OBJECT IDENTIFIER | |||
| rptrInfo | 1.3.6.1.4.1.207.8.1.1 | ||
| OBJECT IDENTIFIER | |||
| actualIPAddr | 1.3.6.1.4.1.207.8.1.1.1 | ||
| The actual IP Address that is currently being used by the hub. This could be the same value as hubIPAddr, or it may be different if another IP Address was received via Bootp. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| hubIPAddr | 1.3.6.1.4.1.207.8.1.1.2 | ||
| The configured IP Address of the hub. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| subnetMask | 1.3.6.1.4.1.207.8.1.1.3 | ||
| Subnet mask of the hub. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| routerAddr | 1.3.6.1.4.1.207.8.1.1.4 | ||
| Gateway/router address of the hub. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| snmpManager | 1.3.6.1.4.1.207.8.1.1.5 | ||
| IP Address of the hub's SNMP manager to which Traps will be sent. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| softwareProduct | 1.3.6.1.4.1.207.8.1.1.6 | ||
| The ATI software product model number running in the hub. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| softwareLevel | 1.3.6.1.4.1.207.8.1.1.7 | ||
| The software release level running in the hub. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| configurationChanged | 1.3.6.1.4.1.207.8.1.1.8 | ||
| A flag, set to the value changed(1) when any of the hub's status or configuration has been changed. When this object is read, then the value is reset to nochange(2). | |||
| OBJECT-TYPE | |||
| INTEGER | changed(1), nochange(2) | ||
| rptrNmMgrTable | 1.3.6.1.4.1.207.8.1.1.9 | ||
| A list of SNMP Trap Manager stations Entries. The number of entries is given by the rptrNmMgrTotal mib object. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| RptrNmMgrEntry | |||
| rptrNmMgrEntry | 1.3.6.1.4.1.207.8.1.1.9.1 | ||
| An Trap receipt Manager Entry containing ipaddress of the configured NMS's to which Traps are sent. | |||
| OBJECT-TYPE | |||
| RptrNmMgrEntry | |||
| rptrNmMgrIndex | 1.3.6.1.4.1.207.8.1.1.9.1.1 | ||
| The Index of SNMP Managers IP Address. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..4 | ||
| rptrNmMgrIpAddr | 1.3.6.1.4.1.207.8.1.1.9.1.2 | ||
| The IP Address of the NMS host configured. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| deviceTable | 1.3.6.1.4.1.207.8.1.1.10 | ||
| The table contains the mapping of all devices in the chassis. For all hubs and switches, the object 'deviceQuadrant' returns 'right' (1). For docking devices, then it will reflect the position of the device in the docking station. This object is specific to Turbo Stack. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| DeviceEntry | |||
| deviceEntry | 1.3.6.1.4.1.207.8.1.1.10.1 | ||
| The device entry in the DeviceTable. | |||
| OBJECT-TYPE | |||
| DeviceEntry | |||
| deviceIndex | 1.3.6.1.4.1.207.8.1.1.10.1.1 | ||
| The Slot number in the chassis where the device is installed. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..8 | ||
| deviceQuadrant | 1.3.6.1.4.1.207.8.1.1.10.1.2 | ||
| The Quadrant of the device. | |||
| OBJECT-TYPE | |||
| INTEGER | right(1), left(2) | ||
| deviceDescr | 1.3.6.1.4.1.207.8.1.1.10.1.3 | ||
| TurboStack product family only. A textual description of the device. For devices that are repeaters, this value is identical to the rptrGroupDescr object. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| deviceObjectID | 1.3.6.1.4.1.207.8.1.1.10.1.4 | ||
| TurboStack product family only. The sysObject identification of the device. For devices that are repeaters, this value is identical to the rptrGroupObjectID object. | |||
| OBJECT-TYPE | |||
| OBJECT IDENTIFIER | |||
| deviceIpAddr | 1.3.6.1.4.1.207.8.1.1.10.1.5 | ||
| TurboStack product family only. The IP address (if present) of the device. For hubs devices, this object will return the same value as hubIPAddr. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| devicePortCapacity | 1.3.6.1.4.1.207.8.1.1.10.1.6 | ||
| TurboStack product family only. The number of ports contained within the device. Valid range is 1-1024. Within each device, the ports are uniquely numbered in the range from 1 to devicePortCapacity. For devices that are repeaters, this value is identical to the rptrGroupPortCapacity object. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..1024 | ||
| localOmegaState | 1.3.6.1.4.1.207.8.1.1.11 | ||
| This object enables the Local Omega to be enabled or disabled. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| remoteOmegaState | 1.3.6.1.4.1.207.8.1.1.12 | ||
| This object enables the Remote Omega to be enabled or disabled. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| groupInfo | 1.3.6.1.4.1.207.8.1.2 | ||
| OBJECT IDENTIFIER | |||
| ledInfo | 1.3.6.1.4.1.207.8.1.2.1 | ||
| See groupLEDInfo | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| groupInfoTable | 1.3.6.1.4.1.207.8.1.2.2 | ||
| Table of group specific information. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| GroupInfoEntry | |||
| groupInfoEntry | 1.3.6.1.4.1.207.8.1.2.2.1 | ||
| An entry in the table, containing information about a single group of ports. | |||
| OBJECT-TYPE | |||
| GroupInfoEntry | |||
| groupInfoIndex | 1.3.6.1.4.1.207.8.1.2.2.1.1 | ||
| This object identifies the group within the repeater for which this entry contains information. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..1024 | ||
| groupLEDInfo | 1.3.6.1.4.1.207.8.1.2.2.1.2 | ||
| This information encodes the current state of the module per-port LEDs. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| groupSegmentation | 1.3.6.1.4.1.207.8.1.2.2.1.3 | ||
| AT-3100 product family only. This object controls the segmentation option for this group. It may be segmented, connected, or using the module's external segmentation switch. | |||
| OBJECT-TYPE | |||
| INTEGER | segmented(1), connected(2), external(3) | ||
| groupSecurity | 1.3.6.1.4.1.207.8.1.2.2.1.4 | ||
| AT-3100 product family only. This object controls the Security option for this group. It may be enabled, disabled, or using module's external security switch. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2), external(3) | ||
| groupIntruderProtection | 1.3.6.1.4.1.207.8.1.2.2.1.5 | ||
| AT-3100 and TurboStack product families only. This object controls the Intruder Protection option for this group/module. For TurboStack products, disabled turns off Intruder Protection and places the module into source address Learning Mode. Enabled turns on Intruder Protection and places the module into Secure Mode. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| groupSrcAddrLearningMode | 1.3.6.1.4.1.207.8.1.2.2.1.6 | ||
| AT-3100 product family only. This object indicates the Source Address Learning Mode. Mode1 : Automatic; passive devices: Automatic MAC address learning. Re-learn port MAC address after a port is disabled/re-enabled. Passive devices connected to a port will see all backbone traffic. Mode2 : Automatic; passive devices: Automatic MAC address learning. Re-learn port MAC address after link test fails (cable removed). Passive devices connected to a port will see all backbone traffic. Mode3 : Manual: No automatic MAC address learning (disabled). Mode4 : Automatic; active devices: Automatic MAC address learning. Re-learn port MAC address after a port is disabled/re-enabled. Passive devices connected to a port will see no backbone traffic. | |||
| OBJECT-TYPE | |||
| INTEGER | mode1(1), mode2(2), mode3(3), mode4(4) | ||
| groupIntruderTrap | 1.3.6.1.4.1.207.8.1.2.2.1.7 | ||
| AT-3100 and TurboStack product families only. This object controls the action to be taken by this group/module when an Intruder Alert event occurs. When this option is enabled, the detection of an intruder (a received packet with an unlearned or undefined source address) causes a Trap to be sent to the configured host manager. When this option is disabled then no Trap is sent on an Intruder Alert event. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| groupIntruderDisable | 1.3.6.1.4.1.207.8.1.2.2.1.8 | ||
| AT-3100 and TurboStack product families only. This object controls the action to be taken by this group/module when an Intruder Alert event occurs. When this option is enabled, the detection of an intruder (a received packet with an unlearned or undefined source address) causes the port where the intruder was detected to be automatically disabled. When this option is disabled then the port will not be disabled on an Intruder Alert event. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| groupOperStatus | 1.3.6.1.4.1.207.8.1.2.2.1.9 | ||
| TurboStack product family only. An object that indicates the operational status of the module. For modules that are repeaters, this value is identical to the rptrGroupOperStatus object. A status of operational(2) indicates that the module is present and functional within the chassis. A status of malfunctioning(3) indicates that the module is present within the chassis but is not functional. A status of notPresent(4) indicates that the module is temporarily or permanently physically and/or logically not a part of the chassis. | |||
| OBJECT-TYPE | |||
| INTEGER | operational(2), malfunctioning(3), notPresent(4) | ||
| groupDescr | 1.3.6.1.4.1.207.8.1.2.2.1.10 | ||
| TurboStack product family only. A textual description of the module. For modules that are repeaters, this value is identical to the rptrGroupDescr object. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| groupObjectID | 1.3.6.1.4.1.207.8.1.2.2.1.11 | ||
| TurboStack product family only. The sysObject identification of the module. For modules that are repeaters, this value is identical to the rptrGroupObjectID object. | |||
| OBJECT-TYPE | |||
| OBJECT IDENTIFIER | |||
| groupIPAddress | 1.3.6.1.4.1.207.8.1.2.2.1.12 | ||
| TurboStack product family only. The IP address (if any) of the module. For modules that are repeaters, this value is identical to the actualIPAddr object. For non-repeater modules, this object identifies the IP address that may be used to communicate directly with the module. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| groupPortCapacity | 1.3.6.1.4.1.207.8.1.2.2.1.13 | ||
| TurboStack product family only. The number of ports contained within the module. Valid range range is 1-1024. Within each module, the ports are uniquely numbered in the range from 1 to groupPortCapacity. For modules that are repeaters, this value is identical to the rptrGroupPortCapacity object. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..1024 | ||
| groupEraseSourceAddressTable | 1.3.6.1.4.1.207.8.1.2.2.1.14 | ||
| TurboStack product family only. This object, when Set to the erase value, will clear (empty) the module Source Address Table, deleting all learned MAC addresses; this object will then automatically revert back to the noerase state. When Set to noerase, no action is taken and the Source Address Table remains unmodified. A Get of this object will always return the noerase value. | |||
| OBJECT-TYPE | |||
| INTEGER | noerase(1), erase(2) | ||
| groupAddSourceAddress | 1.3.6.1.4.1.207.8.1.2.2.1.15 | ||
| TurboStack product family only. This object, when Set with a 48-bit MAC address value, will add the new MAC address to the module Source Address Table. A Get of this object will return a string of length zero. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(6) | ||
| groupDeleteSourceAddress | 1.3.6.1.4.1.207.8.1.2.2.1.16 | ||
| TurboStack product family only. This object, when Set with a 48-bit MAC address value, will delete the MAC address from the module Source Address Table. A Get of this object will return a string of length zero. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(6) | ||
| groupLimitAddressPerPort | 1.3.6.1.4.1.207.8.1.2.2.1.17 | ||
| TurboStack product family only. This object configures the module to allow no limitation on number of source addresses on its ports, or limit to only 1 source address per port. | |||
| OBJECT-TYPE | |||
| INTEGER | noLimit(1), limit1Address(2) | ||
| groupCheckPrimaryTimer | 1.3.6.1.4.1.207.8.1.2.2.1.18 | ||
| TurboStack product family only. The Check Primary Timer is the timer value in seconds which determines how long to wait before checking if the primary port could receive again. This timer applies when the secondary port is enabled, and the primary port's failure is NOT due to loss of link. Range: 1 - 65535 in seconds, 0 means don't check receives. Default is 60 seconds. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..65535 | ||
| groupReceiveFailureTimer | 1.3.6.1.4.1.207.8.1.2.2.1.19 | ||
| TurboStack product family only. The Receive Failure Timer is the timer value in seconds which determines how long to wait before the secondary port takes over when the primary port is not receiving data. This timer applies only when the primary port's failure is NOT due to loss of link. Range: 0 - 65535 in seconds, 0 means don't check receives. Default is 60 seconds. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..65535 | ||
| groupCheckResampleTimer | 1.3.6.1.4.1.207.8.1.2.2.1.20 | ||
| TurboStack product family only. The Resample Timer is the timer value in milliseconds which determines how long to sample/test if the primary port could receive data or is no longer partitioned. This timer begins once groupCheckPrimaryTimer has expired, and during this sampling time, the secondary port cannot repeat data. Range: 100 - 65535 milliseconds. Default is 200 milliseconds. | |||
| OBJECT-TYPE | |||
| INTEGER | 100..65535 | ||
| portInfo | 1.3.6.1.4.1.207.8.1.3 | ||
| OBJECT IDENTIFIER | |||
| atiPortTable | 1.3.6.1.4.1.207.8.1.3.1 | ||
| Table of descriptive and status information about the ports. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AtiPortEntry | |||
| atiPortEntry | 1.3.6.1.4.1.207.8.1.3.1.1 | ||
| An entry in the table, containing information about a single port. | |||
| OBJECT-TYPE | |||
| AtiPortEntry | |||
| atiPortGroupIndex | 1.3.6.1.4.1.207.8.1.3.1.1.1 | ||
| This object identifies the group containing the port for which this entry contains information. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..1024 | ||
| atiPortIndex | 1.3.6.1.4.1.207.8.1.3.1.1.2 | ||
| This object identifies the port within the group for which this entry contains information. This value can never be greater than rptrGroupPortCapacity for the associated group. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..1024 | ||
| portName | 1.3.6.1.4.1.207.8.1.3.1.1.3 | ||
| Port Name | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| portState | 1.3.6.1.4.1.207.8.1.3.1.1.4 | ||
| Port State option: enabled allow repeating of packets through the port; disabled turns off the port and prevents packets repeating through the port. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2), enabledByRedund(3), disabledByRedund(4) | ||
| linkTest | 1.3.6.1.4.1.207.8.1.3.1.1.5 | ||
| Link Test option: enabled turns on checking for link test signals for the port; disabled turns off checking for link test signals. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| altReconnection | 1.3.6.1.4.1.207.8.1.3.1.1.6 | ||
| Reconnection Method: 1=IEEE Standard, 2=Alternate. | |||
| OBJECT-TYPE | |||
| INTEGER | standardIEEE(1), alternate(2) | ||
| polarityCorrection | 1.3.6.1.4.1.207.8.1.3.1.1.7 | ||
| Polarity Correction option: enabled turns on automatic polarity correction for the port; disabled turns off automatic polarity correction. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| partitionedLED | 1.3.6.1.4.1.207.8.1.3.1.1.8 | ||
| This object reflects the current actual partitioning state of the port. The notpartitioned value means that the port is operational and repeating through the port is enabled. The partitioned value means that the port is not operational and repeating through the port is disabled. | |||
| OBJECT-TYPE | |||
| INTEGER | notpartitioned(1), partitioned(2) | ||
| linkTestLED | 1.3.6.1.4.1.207.8.1.3.1.1.9 | ||
| This object reflects the current actual link test state of the port. The nolinktesterror value means that valid link integrity test signals have been detected on the port, indicating that an operable device is cabled to the port. The linktesterror value means that no link integrity test signals have been detected, indicating removal or failure of the port-to-device cable, or that the device is not operational. This object applies only to UTP (twisted pair) and fiber optic ports (not AUI or BNC ports). | |||
| OBJECT-TYPE | |||
| INTEGER | nolinktesterror(1), linktesterror(2) | ||
| polarityLED | 1.3.6.1.4.1.207.8.1.3.1.1.10 | ||
| This object reflects the current actual polarity state of the port. The notreversed value means that the port-to-device cable connection is properly polarized. The reversed value means that the cable connection has reversed polarity. This object applies only to UTP (twisted pair) and fiber optic ports (not AUI or BNC ports). | |||
| OBJECT-TYPE | |||
| INTEGER | notreversed(1), reversed(2) | ||
| portMACAddress | 1.3.6.1.4.1.207.8.1.3.1.1.11 | ||
| AT-3100 product family only. This object is either the MAC address of the last readable frame (i.e., counted by rptrMonitorPortReadableFrames) received by this port, or a manually input MAC address. If neither of those exists, then a string of length zero is returned. If a 'read' operation is performed on this object, the value it returns is the same as the value returned by object 'rptrAddrTrackNewLastSrcAddress' in the Standard Repeater MIB (RFC1516). | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| portFrames-64-127bytes | 1.3.6.1.4.1.207.8.1.3.1.1.12 | ||
| TurboStack product family only. The number of readable frames received on this port where the frame length was in the range 64 through 127 octets. | |||
| OBJECT-TYPE | |||
| Counter | |||
| portFrames-128-255bytes | 1.3.6.1.4.1.207.8.1.3.1.1.13 | ||
| TurboStack product family only. The number of readable frames received on this port where the frame length was in the range 128 through 255 octets. | |||
| OBJECT-TYPE | |||
| Counter | |||
| portFrames-256-511bytes | 1.3.6.1.4.1.207.8.1.3.1.1.14 | ||
| TurboStack product family only. The number of readable frames received on this port where the frame length was in the range 256 through 511 octets. | |||
| OBJECT-TYPE | |||
| Counter | |||
| portFrames-512-1023bytes | 1.3.6.1.4.1.207.8.1.3.1.1.15 | ||
| TurboStack product family only. The number of readable frames received on this port where the frame length was in the range 512 through 1023 octets. | |||
| OBJECT-TYPE | |||
| Counter | |||
| portFrames-1024-1518bytes | 1.3.6.1.4.1.207.8.1.3.1.1.16 | ||
| TurboStack product family only. The number of readable frames received on this port where the frame length was in the range 1024 through 1518 octets. | |||
| OBJECT-TYPE | |||
| Counter | |||
| portRedundantPort | 1.3.6.1.4.1.207.8.1.3.1.1.17 | ||
| TurboStack product family only. This is the redundant port for atiPortIndex. If the port is a secondary port as indicated in portRedundantPosition, then it serves as a backup port. This would indicate paired ports with redundant link. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| portRedundantPosition | 1.3.6.1.4.1.207.8.1.3.1.1.18 | ||
| TurboStack product family only. This object will retrieve the redundant position of the port, primary or secondary port, if the port has a redundant link to it. | |||
| OBJECT-TYPE | |||
| INTEGER | primary(1), secondary(2), notapplicable(3) | ||
| portLearningState | 1.3.6.1.4.1.207.8.1.3.1.1.19 | ||
| TurboStack product family only. This object enable the learning on a port to be shut ON or OFF. Once the learning is Shut Off, the learning of MAC Address will stop. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| rptrStat | 1.3.6.1.4.1.207.8.1.4 | ||
| OBJECT IDENTIFIER | |||
| hubReadableFrames | 1.3.6.1.4.1.207.8.1.4.1 | ||
| The sum total of the Readable Frames Counters of all ports on all modules/groups | |||
| OBJECT-TYPE | |||
| Counter | |||
| hubReadableOctets | 1.3.6.1.4.1.207.8.1.4.2 | ||
| The sum total of the Readable Octets (bytes) Counters of all ports on all modules/groups | |||
| OBJECT-TYPE | |||
| Counter | |||
| hubFCSError | 1.3.6.1.4.1.207.8.1.4.3 | ||
| The sum total of the FCS (CRC) Error Counters of all ports on all modules/groups | |||
| OBJECT-TYPE | |||
| Counter | |||
| hubAlignError | 1.3.6.1.4.1.207.8.1.4.4 | ||
| The sum total of the Alignment Error Counters of all ports on all modules/groups | |||
| OBJECT-TYPE | |||
| Counter | |||
| hubFrameTooLong | 1.3.6.1.4.1.207.8.1.4.5 | ||
| The sum total of the Frame Too Long Error Counters of all ports on all modules/groups | |||
| OBJECT-TYPE | |||
| Counter | |||
| hubShortEvent | 1.3.6.1.4.1.207.8.1.4.6 | ||
| The sum total of the Short Event Error Counters of all ports on all modules/groups | |||
| OBJECT-TYPE | |||
| Counter | |||
| hubRunt | 1.3.6.1.4.1.207.8.1.4.7 | ||
| The sum total of the Runt Error Counters of all ports on all modules/groups | |||
| OBJECT-TYPE | |||
| Counter | |||
| hubLateEvent | 1.3.6.1.4.1.207.8.1.4.8 | ||
| The sum total of the Late Event Error Counters of all ports on all modules/groups | |||
| OBJECT-TYPE | |||
| Counter | |||
| hubVeryLongEvent | 1.3.6.1.4.1.207.8.1.4.9 | ||
| The sum total of the Very Long Event Error (Jabber) Counters of all ports on all modules/groups | |||
| OBJECT-TYPE | |||
| Counter | |||
| hubDataRateMism | 1.3.6.1.4.1.207.8.1.4.10 | ||
| The sum total of the Data Rate Mismatch Error Counters of all ports on all modules/groups | |||
| OBJECT-TYPE | |||
| Counter | |||
| hubAutoPartition | 1.3.6.1.4.1.207.8.1.4.11 | ||
| The sum total of the Auto Port Partition Counters of all ports on all modules/groups | |||
| OBJECT-TYPE | |||
| Counter | |||
| hubTotalError | 1.3.6.1.4.1.207.8.1.4.12 | ||
| The sum total of all Error Counters of all ports on all modules/groups | |||
| OBJECT-TYPE | |||
| Counter | |||
| hubPortCollision | 1.3.6.1.4.1.207.8.1.4.13 | ||
| The sum total of the Port Collision Counters of all ports on all modules/groups | |||
| OBJECT-TYPE | |||
| Counter | |||
| hubFrames-64-127bytes | 1.3.6.1.4.1.207.8.1.4.14 | ||
| TurboStack product family only. The sum total number of readable frames received on all ports on all modules/groups, where the frame length was in the range 64 through 127 octets. | |||
| OBJECT-TYPE | |||
| Counter | |||
| hubFrames-128-255bytes | 1.3.6.1.4.1.207.8.1.4.15 | ||
| TurboStack product family only. The sum total number of readable frames received on all ports on all modules/groups, where the frame length was in the range 128 through 255 octets. | |||
| OBJECT-TYPE | |||
| Counter | |||
| hubFrames-256-511bytes | 1.3.6.1.4.1.207.8.1.4.16 | ||
| TurboStack product family only. The sum total number of readable frames received on all ports on all modules/groups, where the frame length was in the range 256 through 511 octets. | |||
| OBJECT-TYPE | |||
| Counter | |||
| hubFrames-512-1023bytes | 1.3.6.1.4.1.207.8.1.4.17 | ||
| TurboStack product family only. The sum total number of readable frames received on all ports on all modules/groups, where the frame length was in the range 512 through 1023 octets. | |||
| OBJECT-TYPE | |||
| Counter | |||
| hubFrames-1024-1518bytes | 1.3.6.1.4.1.207.8.1.4.18 | ||
| TurboStack product family only. The sum total number of readable frames received on all ports on all modules/groups, where the frame length was in the range 1024 through 1518 octets. | |||
| OBJECT-TYPE | |||
| Counter | |||
| groupStat | 1.3.6.1.4.1.207.8.1.5 | ||
| OBJECT IDENTIFIER | |||
| groupStatTable | 1.3.6.1.4.1.207.8.1.5.1 | ||
| Table of performance and error statistics for the groups. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| GroupStatEntry | |||
| groupStatEntry | 1.3.6.1.4.1.207.8.1.5.1.1 | ||
| An entry in the table, containing total performance and error statistics for a single group. Regular retrieval of the information in this table provides a means of tracking the performance and health of the networked devices attached to this group's ports. The counters in this table are redundant in the sense that they are the summations of information already available through other objects. However, these sums provide a considerable optimization of network management traffic over the otherwise necessary retrieval of the individual counters included in each sum. | |||
| OBJECT-TYPE | |||
| GroupStatEntry | |||
| groupStatIndex | 1.3.6.1.4.1.207.8.1.5.1.1.1 | ||
| This object identifies the group within the repeater for which this entry contains information. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..1024 | ||
| groupFCSError | 1.3.6.1.4.1.207.8.1.5.1.1.2 | ||
| The sum total of the FCS (CRC) Error Counters of all ports on this module/group | |||
| OBJECT-TYPE | |||
| Counter | |||
| groupAlignError | 1.3.6.1.4.1.207.8.1.5.1.1.3 | ||
| The sum total of the Alignment Error Counters of all ports on this module/group | |||
| OBJECT-TYPE | |||
| Counter | |||
| groupFrameTooLong | 1.3.6.1.4.1.207.8.1.5.1.1.4 | ||
| The sum total of the Frame Too Long Error Counters of all ports on this module/group | |||
| OBJECT-TYPE | |||
| Counter | |||
| groupShortEvent | 1.3.6.1.4.1.207.8.1.5.1.1.5 | ||
| The sum total of the Short Event Error Counters of all ports on this module/group | |||
| OBJECT-TYPE | |||
| Counter | |||
| groupRunt | 1.3.6.1.4.1.207.8.1.5.1.1.6 | ||
| The sum total of the Runt Error Counters of all ports on this module/group | |||
| OBJECT-TYPE | |||
| Counter | |||
| groupPortCollision | 1.3.6.1.4.1.207.8.1.5.1.1.7 | ||
| The sum total of the Port Collision Counters of all ports on this module/group | |||
| OBJECT-TYPE | |||
| Counter | |||
| groupLateEvent | 1.3.6.1.4.1.207.8.1.5.1.1.8 | ||
| The sum total of the Late Event Error Counters of all ports on this module/group | |||
| OBJECT-TYPE | |||
| Counter | |||
| groupVeryLongEvent | 1.3.6.1.4.1.207.8.1.5.1.1.9 | ||
| The sum total of the Very Long Event Error (Jabber) Counters of all ports on this module/group | |||
| OBJECT-TYPE | |||
| Counter | |||
| groupDataRateMism | 1.3.6.1.4.1.207.8.1.5.1.1.10 | ||
| The sum total of the Data Rate Mismatch Error Counters of all ports on this module/group | |||
| OBJECT-TYPE | |||
| Counter | |||
| groupAutoPartition | 1.3.6.1.4.1.207.8.1.5.1.1.11 | ||
| The sum total of the Auto Port Partition Counters of all ports on this module/group | |||
| OBJECT-TYPE | |||
| Counter | |||
| groupFrames-64-127bytes | 1.3.6.1.4.1.207.8.1.5.1.1.12 | ||
| TurboStack product family only. The sum total number of readable frames received on all ports on this module/group, where the frame length was in the range 64 through 127 octets. | |||
| OBJECT-TYPE | |||
| Counter | |||
| groupFrames-128-255bytes | 1.3.6.1.4.1.207.8.1.5.1.1.13 | ||
| TurboStack product family only. The sum total number of readable frames received on all ports on this module/group, where the frame length was in the range 128 through 255 octets. | |||
| OBJECT-TYPE | |||
| Counter | |||
| groupFrames-256-511bytes | 1.3.6.1.4.1.207.8.1.5.1.1.14 | ||
| TurboStack product family only. The sum total number of readable frames received on all ports on this module/group, where the frame length was in the range 256 through 511 octets. | |||
| OBJECT-TYPE | |||
| Counter | |||
| groupFrames-512-1023bytes | 1.3.6.1.4.1.207.8.1.5.1.1.15 | ||
| TurboStack product family only. The sum total number of readable frames received on all ports on this module/group, where the frame length was in the range 512 through 1023 octets. | |||
| OBJECT-TYPE | |||
| Counter | |||
| groupFrames-1024-1518bytes | 1.3.6.1.4.1.207.8.1.5.1.1.16 | ||
| TurboStack product family only. The sum total number of readable frames received on all ports on this module/group, where the frame length was in the range 1024 through 1518 octets. | |||
| OBJECT-TYPE | |||
| Counter | |||
| groupSAT | 1.3.6.1.4.1.207.8.1.6 | ||
| OBJECT IDENTIFIER | |||
| groupSourceAddressTable | 1.3.6.1.4.1.207.8.1.6.1 | ||
| TurboStack product family only. Table of learned and/or configured source MAC addresses which defines the only valid and allowable source addresses for this module (if Intruder Protection is enabled). | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| GroupSATEntry | |||
| groupSATEntry | 1.3.6.1.4.1.207.8.1.6.1.1 | ||
| TurboStack product family only. An entry in the Source Address Table, containing information about a single source MAC address. | |||
| OBJECT-TYPE | |||
| GroupSATEntry | |||
| groupSATModule | 1.3.6.1.4.1.207.8.1.6.1.1.1 | ||
| TurboStack product family only. This object identifies the group within the repeater for which this entry contains information. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..1024 | ||
| groupSATIndex | 1.3.6.1.4.1.207.8.1.6.1.1.2 | ||
| TurboStack product family only. This object identifies the index within the Source Address Table for which this entry contains information. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..1024 | ||
| groupSATMacAddress | 1.3.6.1.4.1.207.8.1.6.1.1.3 | ||
| TurboStack product family only. This object is the learned or configured source MAC address. If no MAC address has been learned for this table entry (if this is beyond the logical end of the table) then a string of zero length will be returned. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(6) | ||
| groupSATPort | 1.3.6.1.4.1.207.8.1.6.1.1.4 | ||
| TurboStack product family only. This object is the port number where the source MAC address was last detected. If the MAC address has not been detected since the system was last started, then this object will be zero. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..1024 | ||
| atiTrapAttrs | 1.3.6.1.4.1.207.9 | ||
| OBJECT IDENTIFIER | |||
| atiTrapIntruderMacAddress | 1.3.6.1.4.1.207.9.1 | ||
| The Mac address of the Intruder which is different from the rfc1516 object rptrAddrTrackLastSourceAddress is seen on port which is the the next object | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(6) | ||
| atiTrapIntruderModuleNumber | 1.3.6.1.4.1.207.9.2 | ||
| This is the module number on which an intruder was seen. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| atiTrapIntruderPortNumber | 1.3.6.1.4.1.207.9.3 | ||
| This is the port number on which an intruder was seen. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| atiPortChangeDirection | 1.3.6.1.4.1.207.9.4 | ||
| This is the direction of redundant port change. These two values are used in the trap atiRedundantPortChangeTrap. | |||
| OBJECT-TYPE | |||
| INTEGER | primarytosecondary(1), secondarytoprimary(2) | ||
| MacAddress | |||
| OCTET STRING | SIZE(6) | ||
| RptrNmMgrEntry | |||
| SEQUENCE | |||
| INTEGER as rptrNmMgrIndex | |||
| IpAddress as rptrNmMgrIpAddr | |||
| DeviceEntry | |||
| SEQUENCE | |||
| INTEGER as deviceIndex | |||
| INTEGER as deviceQuadrant | |||
| DisplayString as deviceDescr | |||
| OBJECT IDENTIFIER as deviceObjectID | |||
| IpAddress as deviceIpAddr | |||
| INTEGER as devicePortCapacity | |||
| GroupInfoEntry | |||
| SEQUENCE | |||
| INTEGER as groupInfoIndex | |||
| OCTET STRING as groupLEDInfo | |||
| INTEGER as groupSegmentation | |||
| INTEGER as groupSecurity | |||
| INTEGER as groupIntruderProtection | |||
| INTEGER as groupSrcAddrLearningMode | |||
| INTEGER as groupIntruderTrap | |||
| INTEGER as groupIntruderDisable | |||
| INTEGER as groupOperStatus | |||
| DisplayString as groupDescr | |||
| OBJECT IDENTIFIER as groupObjectID | |||
| IpAddress as groupIPAddress | |||
| INTEGER as groupPortCapacity | |||
| INTEGER as groupEraseSourceAddressTable | |||
| OCTET STRING as groupAddSourceAddress | |||
| OCTET STRING as groupDeleteSourceAddress | |||
| INTEGER as groupLimitAddressPerPort | |||
| INTEGER as groupCheckPrimaryTimer | |||
| INTEGER as groupReceiveFailureTimer | |||
| INTEGER as groupCheckResampleTimer | |||
| GroupStatEntry | |||
| SEQUENCE | |||
| INTEGER as groupStatIndex | |||
| Counter as groupFCSError | |||
| Counter as groupAlignError | |||
| Counter as groupFrameTooLong | |||
| Counter as groupShortEvent | |||
| Counter as groupRunt | |||
| Counter as groupPortCollision | |||
| Counter as groupLateEvent | |||
| Counter as groupVeryLongEvent | |||
| Counter as groupDataRateMism | |||
| Counter as groupAutoPartition | |||
| Counter as groupFrames-64-127bytes | |||
| Counter as groupFrames-128-255bytes | |||
| Counter as groupFrames-256-511bytes | |||
| Counter as groupFrames-512-1023bytes | |||
| Counter as groupFrames-1024-1518bytes | |||
| GroupSATEntry | |||
| SEQUENCE | |||
| INTEGER as groupSATModule | |||
| INTEGER as groupSATIndex | |||
| OCTET STRING as groupSATMacAddress | |||
| INTEGER as groupSATPort | |||
| AtiPortEntry | |||
| SEQUENCE | |||
| INTEGER as atiPortGroupIndex | |||
| INTEGER as atiPortIndex | |||
| DisplayString as portName | |||
| INTEGER as portState | |||
| INTEGER as linkTest | |||
| INTEGER as altReconnection | |||
| INTEGER as polarityCorrection | |||
| INTEGER as partitionedLED | |||
| INTEGER as linkTestLED | |||
| INTEGER as polarityLED | |||
| MacAddress as portMACAddress | |||
| Counter as portFrames-64-127bytes | |||
| Counter as portFrames-128-255bytes | |||
| Counter as portFrames-256-511bytes | |||
| Counter as portFrames-512-1023bytes | |||
| Counter as portFrames-1024-1518bytes | |||
| INTEGER as portRedundantPort | |||
| INTEGER as portRedundantPosition | |||
| INTEGER as portLearningState | |||