ATM-SOFT-PVC-MIB

File: ATM-SOFT-PVC-MIB.mib (35932 bytes)

Imported modules

RFC1155-SMI SNMPv2-SMI RFC-1212
RFC-1215 SNMPv2-TC-v1 IF-MIB
ATM-MIB

Imported symbols

enterprises Counter32 Gauge32
OBJECT-TYPE TRAP-TYPE RowStatus
TruthValue TimeStamp ifIndex
atmVplVpi atmVclVpi atmVclVci

Defined Objects

atmForum 1.3.6.1.4.1.353
OBJECT IDENTIFIER    

atmForumNetworkManagement 1.3.6.1.4.1.353.5
OBJECT IDENTIFIER    

atmfSoftPvc 1.3.6.1.4.1.353.5.5
OBJECT IDENTIFIER    

atmSoftPvcMIB 1.3.6.1.4.1.353.5.5.1
OBJECT IDENTIFIER    

atmSoftPvcMIBObjects 1.3.6.1.4.1.353.5.5.1.1
OBJECT IDENTIFIER    

atmSoftPvcBaseGroup 1.3.6.1.4.1.353.5.5.1.1.1
OBJECT IDENTIFIER    

atmSoftPvcCallFailuresTrapEnable 1.3.6.1.4.1.353.5.5.1.1.1.1
Allows the generation of traps in response to call failures. By default, this object is set to 'false'.
OBJECT-TYPE    
  TruthValue  

atmSoftPvcCallFailures 1.3.6.1.4.1.353.5.5.1.1.1.2
The number of times a series of call attempts has failed to establish a Soft PVCC or Soft PVPC. The number of call attempts in a series is determined by atmSoftPVccRetryThreshold or atmSoftPVpcRetryThreshold, respectively.
OBJECT-TYPE    
  Counter32  

atmSoftPvcCurrentlyFailingSoftPVccs 1.3.6.1.4.1.353.5.5.1.1.1.3
The current number of Soft PVCCs for which there is an active row in the atmSoftPVccTable having an atmSoftPVccOperStatus with a value other than 'connected'.
OBJECT-TYPE    
  Gauge32  

atmSoftPvcCurrentlyFailingSoftPVpcs 1.3.6.1.4.1.353.5.5.1.1.1.4
The current number of Soft PVPCs for which there is an active row in the atmSoftPVpcTable having an atmSoftPVpcOperStatus with a value other than 'connected'.
OBJECT-TYPE    
  Gauge32  

atmSoftPvcNotificationInterval 1.3.6.1.4.1.353.5.5.1.1.1.5
The minimum interval between the sending of atmSoftPvcCallFailuresTrap notifications.
OBJECT-TYPE    
  INTEGER 0..3600  

atmSoftPVccTable 1.3.6.1.4.1.353.5.5.1.1.2
The (conceptual) table used to manage Soft Permanent Virtual Channel Connections (Soft PVCCs). The Soft PVCC table is applicable only to switches.
OBJECT-TYPE    
  SEQUENCE OF  
    AtmSoftPVccEntry

atmSoftPVccEntry 1.3.6.1.4.1.353.5.5.1.1.2.1
Each entry in this table represents a Soft Permanent Virtual Channel Connection (Soft PVCC) originating at a switch interface. A Soft PVCC is a VCC that is: - provisioned at the originating (source) interface of the connection - established by signalling procedures across a network to a destination interface. A row in the atmVclTable must be created, defining a VCL on the source interface, prior to creating an atmSoftPVccEntry row. The row in the atmVclTable must be active prior to activating the atmSoftPVccEntry row. The contents of this table reflect only the characteristics unique to a Soft PVCC. The traffic parameters are defined in the VCL row for the source interface, as specified in the ATOMMIB (RFC1695) and the forthcoming addition, the Supplemental ATOMMIB. Note that the atmSigDescrParamTable contains some objects such as the AAL parameters, Broadband high layer information and Broadband low layer information elements which are used to carry end-to-end information. For this reason, these objects are not relevant to Soft PVCCs. When a row is made active, an attempt is made to set up a switched connection to an interface at the destination switch. No objects (other than atmSoftPVccRowStatus) can be set while the row is active. At the destination, the VCL may be defined (but not cross-connected) prior to arrival of the Setup request. The combination of ifIndex, atmVclVpi, and atmVclVci specified in the index clause of this entry serves to identify the VCL on the source interface. The atmSoftPVccLeafReference object aids in distinguishing between leaves of a point-to-multipoint Soft PVCC.
OBJECT-TYPE    
  AtmSoftPVccEntry  

atmSoftPVccLeafReference 1.3.6.1.4.1.353.5.5.1.1.2.1.1
An arbitrary integer which, in the case of the source VCL having an atmVclCastType of 'p2mpRoot', serves to distinguish between the multiple leaves attached to a root of a point-to-multipoint Soft PVCC. If the atmVclCastType is not 'p2mpRoot' the value 1 shall be used.
OBJECT-TYPE    
  INTEGER 1..65535  

atmSoftPVccTargetAddress 1.3.6.1.4.1.353.5.5.1.1.2.1.2
The target ATM Address of this Soft PVCC. If no address is supplied, no attempts to establish the Soft PVCC are initiated.
OBJECT-TYPE    
  AtmAddr  

atmSoftPVccTargetSelectType 1.3.6.1.4.1.353.5.5.1.1.2.1.3
Indicates whether the target VPI/VCI values are to be used at the destination. If the value 'any' is specified, the destination switch will choose the VPI/VCI values. In such a case, once the Soft PVCC atmSoftPVccOperStatus value is 'connected', the value of this object changes to 'required', such that the same VPI/VCI values will continue to be used even if the connection is subsequently torn down and re-established. The VPI/VCI values chosen will be available for reading in atmSoftPVccTargetVpi and atmSoftPVccTargetVci. If the value 'required' is specified, then values must be supplied for objects atmSoftPVccTargetVpi and atmSoftPVccTargetVci prior to activation of the row. These values are then to be used at the destination.
OBJECT-TYPE    
  INTEGER required(1), any(2)  

atmSoftPVccTargetVpi 1.3.6.1.4.1.353.5.5.1.1.2.1.4
The VPI value of the VCL used at the target interface. This value is not relevant when the value of atmSoftPVccTargetSelectType is 'any'.
OBJECT-TYPE    
  INTEGER 0..4095  

atmSoftPVccTargetVci 1.3.6.1.4.1.353.5.5.1.1.2.1.5
The VCI value of the VCL used at the target interface. This value must be filled in when the atmSoftPVccTargetSelectType is set to 'required'.This value is not relevant when the value of atmSoftPVccTargetSelectType is 'any'.
OBJECT-TYPE    
  INTEGER 0..65535  

atmSoftPVccLastReleaseCause 1.3.6.1.4.1.353.5.5.1.1.2.1.6
Value of the Cause field of the Cause Information Element in the last RELEASE signalling message received for this Soft PVCC. Indicates the reason for the Release.
OBJECT-TYPE    
  INTEGER 1..127  

atmSoftPVccLastReleaseDiagnostic 1.3.6.1.4.1.353.5.5.1.1.2.1.7
Value of the first 8 bytes of diagnostic information from the Cause field of the Cause Information Element in the last RELEASE signalling message received for this Soft PVCC.
OBJECT-TYPE    
  OCTET STRING SIZE(0..8)  

atmSoftPVccOperStatus 1.3.6.1.4.1.353.5.5.1.1.2.1.8
Describes the status of the Soft PVCC. Valid values are: other - none of the types specified below establishmentInProgress - connection or party is not operational, but setup or add party attempts are ongoing connected - connection or party is currently operational retriesExhausted - retry limit has been reached and setup or add party attempts have ceased noAddressSupplied - no remote address has been configured, so no setup or add party attempts are initiated lowerLayerDown - underlying ATM interface is not operational When the row is not 'active', the value of this object is 'other'.
OBJECT-TYPE    
  INTEGER other(1), establishmentInProgress(2), connected(3), retriesExhausted(4), noAddressSupplied(5), lowerLayerDown(6)  

atmSoftPVccRestart 1.3.6.1.4.1.353.5.5.1.1.2.1.9
When the value is set to 'restart' the Soft PVCC is released if necessary and a new setup procedure is begun. As a result of this action, the atmSoftPVccOperStatus object transitions to 'establishmentInProgress' (if not already in this state) and the atmSoftPVccRetryFailures object is cleared When the value is set to 'noop' no operation is performed. When read, the value 'noop' is returned.
OBJECT-TYPE    
  INTEGER restart(1), noop(2)  

atmSoftPVccRetryInterval 1.3.6.1.4.1.353.5.5.1.1.2.1.10
Defines the period to wait before attempting to establish the Soft PVCC after the first failed call attempt. The time to wait between subsequent call attempts may differ to implement a backoff scheme. Zero represents an infinite interval indicating no retries.
OBJECT-TYPE    
  INTEGER 0..3600  

atmSoftPVccRetryTimer 1.3.6.1.4.1.353.5.5.1.1.2.1.11
Indicates the current value of the retry timer for this connection. When the value reaches zero an attempt will be made to establish the Soft PVCC. When the timer is not running, the value zero shall be returned.
OBJECT-TYPE    
  INTEGER 0..86400  

atmSoftPVccRetryThreshold 1.3.6.1.4.1.353.5.5.1.1.2.1.12
Indicates the number of consecutive call setup attempts for the same Soft PVCC which need to fail before the atmSoftPvcCallFailures object is incremented. A value of zero indicates that an infinite number of call attempts are required to increment the atmSoftPvcCallFailures object and thus disables alarms for the Soft PVCC.
OBJECT-TYPE    
  INTEGER 0..65535  

atmSoftPVccRetryFailures 1.3.6.1.4.1.353.5.5.1.1.2.1.13
Indicates how many attempts to establish the connection have failed. This count is reset whenever a connection is successfully established or the Soft PVCC is restarted.
OBJECT-TYPE    
  Gauge32  

atmSoftPVccRetryLimit 1.3.6.1.4.1.353.5.5.1.1.2.1.14
Sets a maximum limit on how many consecutive unsuccessful call setup attempts can be made before stopping the attempt to set up the connection. If this limit is reached then management action will be required (e.g. setting atmSoftPVccRestart to 'restart') to initiate a new attempt to establish the connection. A value of zero indicates no limit - the attempts will continue until successful.
OBJECT-TYPE    
  INTEGER 0..65535  

atmSoftPVccRowStatus 1.3.6.1.4.1.353.5.5.1.1.2.1.15
Used to create and delete a Soft PVCC. When this object is set to 'active' an attempt is made to set up the Soft PVCC. When this object has the value 'active' and is set to another value, any set-up or connection in-progress is released.
OBJECT-TYPE    
  RowStatus  

atmSoftPVpcTable 1.3.6.1.4.1.353.5.5.1.1.3
The (conceptual) table used to manage Soft Permanent Virtual Path Connections (Soft PVPCs) The Soft PVPC table is applicable only to switches.
OBJECT-TYPE    
  SEQUENCE OF  
    AtmSoftPVpcEntry

atmSoftPVpcEntry 1.3.6.1.4.1.353.5.5.1.1.3.1
Each entry in this table represents a Soft Permanent Virtual Path Connection (Soft PVPC) originating at a switch interface. A Soft PVPC is a VPC that is: - provisioned at the originating (source) interface of the connection - established by signalling procedures across a network to a destination interface. A row in the atmVplTable must be created, defining a VPL on the source interface, prior to creating an atmSoftPVpcEntry row. The row in the atmVplTable must be active prior to activating the atmSoftPVpcEntry row. The contents of this table reflect only the characteristics unique to a Soft PVPC. The traffic parameters are defined in the VPL row for the source interface, as specified in the ATOMMIB (RFC1695) and the forthcoming addition, the Supplemental ATOMMIB. Note that the atmSigDescrParamTable contains some objects such as the AAL parameters, Broadband high layer information, and Broadband low layer information elements which are used to carry end-to-end information. For this reason, these objects are not relevant to Soft PVPCs. When a row is made active, an attempt is made to set up a switched connection to an interface at the destination switch. No objects (other than atmSoftPVpcRowStatus) can be set while the row is active. At the destination, the VPL may be defined (but not cross-connected) prior to arrival of the Setup request. The combination of ifIndex, atmVplVpi specified in the index clause of this entry serves to identify the VPL on the source interface. The atmSoftPVpcLeafReference object aids in distinguishing between leaves of a point-to-multipoint Soft PVPC.
OBJECT-TYPE    
  AtmSoftPVpcEntry  

atmSoftPVpcLeafReference 1.3.6.1.4.1.353.5.5.1.1.3.1.1
An arbitrary integer which, in the case of the source VPL having a atmVplCastType of 'p2mpRoot', serves to distinguish between the multiple leaves attached to a root of a point-to-multipoint Soft PVPC. If the atmVplCastType is not 'p2mpRoot', the value 1 shall be used.
OBJECT-TYPE    
  INTEGER 1..63535  

atmSoftPVpcTargetAddress 1.3.6.1.4.1.353.5.5.1.1.3.1.2
The target ATM Address of this Soft PVPC. If no address is supplied, no attempts to establish the Soft PVPC are initiated.
OBJECT-TYPE    
  AtmAddr  

atmSoftPVpcTargetSelectType 1.3.6.1.4.1.353.5.5.1.1.3.1.3
Indicates whether the target VPI value is to be used at the destination. If the value 'any' is specified, the destination switch will choose the VPI value. In such a case, once the Soft PVPC atmSoftPVpcOperStatus value is 'connected', the value of this object changes to 'required', such that the same VPI value will continue to be used even if the connection is subsequently torn down and re-established. The VPI value chosen will be available for reading in atmSoftPVpcTargetVpi. If the value 'required' is specified, then a value must be supplied for object atmSoftPVpcTargetVpi prior to activation of the row. This value is then to be used at the destination.
OBJECT-TYPE    
  INTEGER required(1), any(2)  

atmSoftPVpcTargetVpi 1.3.6.1.4.1.353.5.5.1.1.3.1.4
The VPI value of the VPL used at the target interface. This value must be filled in when the atmSoftPVpcTargetSelectType is set to 'required'. This value is not relevant when the value of atmSoftPVpcTargetSelectType is 'any'.
OBJECT-TYPE    
  INTEGER 0..4095  

atmSoftPVpcLastReleaseCause 1.3.6.1.4.1.353.5.5.1.1.3.1.5
Value of the Cause field of the Cause Information Element in the last RELEASE signalling message received for this Soft PVPC. Indicates the reason for the Release.
OBJECT-TYPE    
  INTEGER 1..127  

atmSoftPVpcLastReleaseDiagnostic 1.3.6.1.4.1.353.5.5.1.1.3.1.6
Value of the first 8 bytes of diagnostic information from the Cause field of the Cause Information Element in the last RELEASE signalling message received for this Soft PVPC.
OBJECT-TYPE    
  OCTET STRING SIZE(0..8)  

atmSoftPVpcOperStatus 1.3.6.1.4.1.353.5.5.1.1.3.1.7
Describes the status of the Soft PVPC. other - none of the types specified below establishmentInProgress - connection or party is not operational, but setup or add party attempts are ongoing connected - connection or party is currently operational retriesExhausted - retry limit has been reached and setup or add party attempts have ceased noAddressSupplied - no remote address has been configured, so no setup or add party attempts are initiated lowerLayerDown - underlying ATM interface is not operational When the row is not 'active', the value of this object is 'other'.
OBJECT-TYPE    
  INTEGER other(1), establishmentInProgress(2), connected(3), retriesExhausted(4), noAddressSupplied(5), lowerLayerDown(6)  

atmSoftPVpcRestart 1.3.6.1.4.1.353.5.5.1.1.3.1.8
When the value is set to 'restart', the Soft PVPC is released if necessary and a new setup procedure is begun. As a result of this action, the atmSoftPVpcOperStatus object transitions to 'establishmentInProgress' (if not already in this state) and the atmSoftPVpcRetryFailures object is cleared. When the value is set to 'noop', no operation is performed. When read, the value 'noop' is returned.
OBJECT-TYPE    
  INTEGER restart(1), noop(2)  

atmSoftPVpcRetryInterval 1.3.6.1.4.1.353.5.5.1.1.3.1.9
Defines the period to wait before attempting to establish the Soft PVPC after the first failed call attempt. The time to wait between subsequent call attempts may differ to implement a backoff scheme. Zero represents an infinite interval indicating no retries.
OBJECT-TYPE    
  INTEGER 0..3600  

atmSoftPVpcRetryTimer 1.3.6.1.4.1.353.5.5.1.1.3.1.10
Indicates the current value of the retry timer for this connection. When the value reaches zero an attempt will be made to establish the Soft PVPC. When the timer is not running, the value zero shall be returned.
OBJECT-TYPE    
  INTEGER 0..86400  

atmSoftPVpcRetryThreshold 1.3.6.1.4.1.353.5.5.1.1.3.1.11
Indicates the number of consecutive call setup attempts for the same Soft PVPC which need to fail before the atmSoftPvcCallFailures object is incremented. A value of zero indicates that an infinite number of call attempts are required to increment the atmSoftPvcCallFailures object and thus disables alarms for the Soft PVPC.
OBJECT-TYPE    
  INTEGER 0..65535  

atmSoftPVpcRetryFailures 1.3.6.1.4.1.353.5.5.1.1.3.1.12
Indicates how many attempts to establish the connection have failed. This count is reset whenever a connection is successfully established or the Soft PVPC is restarted.
OBJECT-TYPE    
  Gauge32  

atmSoftPVpcRetryLimit 1.3.6.1.4.1.353.5.5.1.1.3.1.13
Sets a maximum limit on how many consecutive unsuccessful call setup attempts can be made before stopping the attempt to set up the connection. If this limit is reached then management action will be required (e.g. setting atmSoftPVpcRestart to 'restart') to initiate a new attempt to establish the connection. A value of zero indicates no limit - the attempts will continue until successful.
OBJECT-TYPE    
  INTEGER 0..65535  

atmSoftPVpcRowStatus 1.3.6.1.4.1.353.5.5.1.1.3.1.14
Used to create and delete a Soft PVPC. When this object is set to 'active' an attempt is made to set up the Soft PVPC. When this object has the value 'active' and is set to another value, any set-up or connection in-progress is released.
OBJECT-TYPE    
  RowStatus  

atmInterfaceSoftPvcAddressTable 1.3.6.1.4.1.353.5.5.1.1.4
This table is used to configure ATM addresses at an ATM interface on this node prior to setting up Soft PVPCs or Soft PVPCs at that interface.
OBJECT-TYPE    
  SEQUENCE OF  
    AtmInterfaceSoftPvcAddressEntry

atmInterfaceSoftPvcAddressEntry 1.3.6.1.4.1.353.5.5.1.1.4.1
ATM address entry for configuring Soft PVCCs or Soft PVPCs at an ATM interface.
OBJECT-TYPE    
  AtmInterfaceSoftPvcAddressEntry  

atmInterfaceSoftPvcAddress 1.3.6.1.4.1.353.5.5.1.1.4.1.1
Specifies the address that can be used to establish a Soft PVCC or Soft PVPC to this interface.
OBJECT-TYPE    
  AtmAddr  

atmInterfaceSoftPvcAddressRowStatus 1.3.6.1.4.1.353.5.5.1.1.4.1.2
Used to create and delete an ATM address at this interface for setting up Soft PVCCs or Soft PVPCs.
OBJECT-TYPE    
  RowStatus  

atmCurrentlyFailingSoftPVccTable 1.3.6.1.4.1.353.5.5.1.1.5
A table indicating all Soft Permanent Virtual Channel Connections (Soft PVCCs) for which the atmSoftPVccRowStatus is 'active' and the atmSoftPVccOperStatus is other than 'connected'.
OBJECT-TYPE    
  SEQUENCE OF  
    AtmCurrentlyFailingSoftPVccEntry

atmCurrentlyFailingSoftPVccEntry 1.3.6.1.4.1.353.5.5.1.1.5.1
Each entry in this table represents a Soft Permanent Virtual Channel Connection (Soft PVCC) for which the atmSoftPVccRowStatus is 'active' and the atmSoftPVccOperStatus is other than 'connected'.
OBJECT-TYPE    
  AtmCurrentlyFailingSoftPVccEntry  

atmCurrentlyFailingSoftPVccTimeStamp 1.3.6.1.4.1.353.5.5.1.1.5.1.1
The time at which this Soft PVCC began to fail.
OBJECT-TYPE    
  TimeStamp  

atmCurrentlyFailingSoftPVpcTable 1.3.6.1.4.1.353.5.5.1.1.6
A table indicating all Soft Permanent Virtual Path Connections (Soft PVPCs) for which the atmSoftPVpcRowStatus is 'active' and the atmSoftPVpcOperStatus is other than 'connected'.
OBJECT-TYPE    
  SEQUENCE OF  
    AtmCurrentlyFailingSoftPVpcEntry

atmCurrentlyFailingSoftPVpcEntry 1.3.6.1.4.1.353.5.5.1.1.6.1
Each entry in this table represents a Soft Permanent Virtual Path Connection (Soft PVPC) for which the atmSoftPVpcRowStatus is 'active' and the atmSoftPVpcOperStatus is other than 'connected'.
OBJECT-TYPE    
  AtmCurrentlyFailingSoftPVpcEntry  

atmCurrentlyFailingSoftPVpcTimeStamp 1.3.6.1.4.1.353.5.5.1.1.6.1.1
The time at which this Soft PVPC began to fail.
OBJECT-TYPE    
  TimeStamp  

atmSoftPvcMIBTraps 1.3.6.1.4.1.353.5.5.1.2
OBJECT IDENTIFIER    

atmSoftPvcTraps 1.3.6.1.4.1.353.5.5.1.2.1
OBJECT IDENTIFIER    

atmSoftPvcTrapsPrefix 1.3.6.1.4.1.353.5.5.1.2.1.0
OBJECT IDENTIFIER    

atmSoftPvcCallFailuresTrap 1.3.6.1.4.1.353.5.5.1.2.1.1
A notification indicating that one or more series of call attempts in trying to establish a Soft PVPC or Soft PVCC have failed since the last atmSoftPvcCallFailureTrap was sent. If this trap has not been sent for the last atmSoftPvcNotificationInterval, then it will be sent on the next increment of atmSoftPvcCallFailures.
TRAP-TYPE    
  atmSoftPvcCallFailures  
  atmSoftPvcCurrentlyFailingSoftPVccs  
  atmSoftPvcCurrentlyFailingSoftPVpcs  

atmSoftPvcMIBConformance 1.3.6.1.4.1.353.5.5.1.3
OBJECT IDENTIFIER    

atmSoftPvcMIBCompliances 1.3.6.1.4.1.353.5.5.1.3.1
OBJECT IDENTIFIER    

atmSoftPvcMIBCompliance 1.3.6.1.4.1.353.5.5.1.3.1.1
OBJECT IDENTIFIER    

atmSoftPvcMIBGroups 1.3.6.1.4.1.353.5.5.1.3.2
OBJECT IDENTIFIER    

atmSoftPvcBaseMIBGroup 1.3.6.1.4.1.353.5.5.1.3.2.1
OBJECT IDENTIFIER    

atmSoftPvcVccMIBGroup 1.3.6.1.4.1.353.5.5.1.3.2.2
OBJECT IDENTIFIER    

atmSoftPvcVpcMIBGroup 1.3.6.1.4.1.353.5.5.1.3.2.3
OBJECT IDENTIFIER    

atmSoftPvcAddressMIBGroup 1.3.6.1.4.1.353.5.5.1.3.2.4
OBJECT IDENTIFIER    

atmCurrentlyFailingSoftPVccMIBGroup 1.3.6.1.4.1.353.5.5.1.3.2.5
OBJECT IDENTIFIER    

atmCurrentlyFailingSoftPVpcMIBGroup 1.3.6.1.4.1.353.5.5.1.3.2.6
OBJECT IDENTIFIER    

Defined Objects

AtmAddr  
OCTET STRING SIZE(0 | 8 | 20)    

AtmSoftPVccEntry  
SEQUENCE    
  INTEGER as atmSoftPVccLeafReference  
  AtmAddr as atmSoftPVccTargetAddress  
  INTEGER as atmSoftPVccTargetSelectType  
  INTEGER as atmSoftPVccTargetVpi  
  INTEGER as atmSoftPVccTargetVci  
  INTEGER as atmSoftPVccLastReleaseCause  
  OCTET STRING as atmSoftPVccLastReleaseDiagnostic  
  INTEGER as atmSoftPVccOperStatus  
  INTEGER as atmSoftPVccRestart  
  INTEGER as atmSoftPVccRetryInterval  
  INTEGER as atmSoftPVccRetryTimer  
  INTEGER as atmSoftPVccRetryThreshold  
  Gauge32 as atmSoftPVccRetryFailures  
  INTEGER as atmSoftPVccRetryLimit  
  RowStatus as atmSoftPVccRowStatus  

AtmSoftPVpcEntry  
SEQUENCE    
  INTEGER as atmSoftPVpcLeafReference  
  AtmAddr as atmSoftPVpcTargetAddress  
  INTEGER as atmSoftPVpcTargetSelectType  
  INTEGER as atmSoftPVpcTargetVpi  
  INTEGER as atmSoftPVpcLastReleaseCause  
  OCTET STRING as atmSoftPVpcLastReleaseDiagnostic  
  INTEGER as atmSoftPVpcOperStatus  
  INTEGER as atmSoftPVpcRestart  
  INTEGER as atmSoftPVpcRetryInterval  
  INTEGER as atmSoftPVpcRetryTimer  
  INTEGER as atmSoftPVpcRetryThreshold  
  Gauge32 as atmSoftPVpcRetryFailures  
  INTEGER as atmSoftPVpcRetryLimit  
  RowStatus as atmSoftPVpcRowStatus  

AtmInterfaceSoftPvcAddressEntry  
SEQUENCE    
  AtmAddr as atmInterfaceSoftPvcAddress  
  RowStatus as atmInterfaceSoftPvcAddressRowStatus  

AtmCurrentlyFailingSoftPVccEntry  
SEQUENCE    
  TimeStamp as atmCurrentlyFailingSoftPVccTimeStamp  

AtmCurrentlyFailingSoftPVpcEntry  
SEQUENCE    
  TimeStamp as atmCurrentlyFailingSoftPVpcTimeStamp