
AWC-VLAN-CFG-MIB
File:
AWC-VLAN-CFG-MIB.mib (15449 bytes)
Imported modules
Imported symbols
Defined Objects
| awcVlanEncapMode |
1.3.6.1.4.1.522.3.21.1.2 |
| The encapsulation mode setting controls transmit tagging logic for all ports. The value of this object is derived from other settings within the VLAN MIB. |
| OBJECT-TYPE |
|
|
|
| |
AwcVlanEncapType |
|
|
| awcNativeVlanId |
1.3.6.1.4.1.522.3.21.1.3 |
| Native VLAN ID for the device. The default Native VLAN ID is 0, for no VLAN ID. If the device is attached to an Ethernet bridge/switch VLAN port then a non-zero Native VLAN ID must match the Port VLAN ID of the bridge/switch port. The Native VLAN ID is the default VLAN ID for frames that are not otherwise associated with a VLAN ID. |
| OBJECT-TYPE |
|
|
|
| |
AwcVlanId |
|
|
| awcVlanAllowEncrypted |
1.3.6.1.4.1.522.3.21.1.4 |
| When this attribute is true, the STA shall indicate at the MAC service interface received MSDUs regardless of the setting of the WEP subfield of the Frame Control field, so long as no other VLAN parameters necessitate use of encryption. The default value of this attribute shall be true. The general use for awcVlanAllowEncrypted to be true even when no static WEP keys are set for a VLAN is to allow a station to utilize EAP authentication to encrypt directed packets, even while multicast packets are unencrypted. |
| OBJECT-TYPE |
|
|
|
| |
TruthValue |
|
|
| awcVlanAnyEnabled |
1.3.6.1.4.1.522.3.21.1.5 |
| When this attribute is true, VLAN operation of the system is enabled when any awcVlanEnabled value is true. When this attribute is false, VLAN operation is disabled. The awcVlanAnyEnabled thus acts as a master switch to enable or disable VLAN operation. |
| OBJECT-TYPE |
|
|
|
| |
TruthValue |
|
|
| awcVlanCfgEntry |
1.3.6.1.4.1.522.3.21.1.6.1 |
| VLAN table entry containing parameters for configuring and managing a particular VLAN. |
| OBJECT-TYPE |
|
|
|
| |
AwcVlanCfgEntry |
|
|
| awcVlanIndex |
1.3.6.1.4.1.522.3.21.1.6.1.1 |
| VLAN ID to which the parameters in this conceptual row shall be applied. If 4095, the parameters in this conceptual row shall be applied to non-VLAN-tagged frames. |
| OBJECT-TYPE |
|
|
|
| |
AwcVlanIndex |
|
|
| awcVlanNUcastKeyTable |
1.3.6.1.4.1.522.3.21.1.7 |
| Default Shared WEP Keys for all 802.11 packets transmitted and received as non-VLAN-tagged frames over a port with the Port VLAN ID specified as awcVlanIndex. If WEP encryption is enabled for transmitted 802.11 frames, then the set of 1 to 4 default shared WEP keys are used to encrypt transmitted 802.11 broadcast/multicast frames associated with the Port VLAN ID. The shared WEP keys are also used to encrypt/decrypt unicast frames, associated with the Port VLAN ID, if an individual session key is not defined for the target station address. |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
AwcVlanNUcastKeyEntry |
|
| awcVlanNUcastKeyEntry |
1.3.6.1.4.1.522.3.21.1.7.1 |
| An entry in the awcVlanNUcastKeyTable table. |
| OBJECT-TYPE |
|
|
|
| |
AwcVlanNUcastKeyEntry |
|
|
| awcVlanNUcastKeyIndex |
1.3.6.1.4.1.522.3.21.1.7.1.1 |
| 802.11 WEP Key Index, + 1, used when transmitting or receiving frames with this key. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..4 |
|
| awcVlanNUcastKeyLen |
1.3.6.1.4.1.522.3.21.1.7.1.2 |
| Length in octets of awcVlanNUcastKeyValue. Common values are 5 for 40-bit WEP and 13 for 128-bit WEP. A value of 0 means that the key is not set. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0..13 |
|
Defined Objects
| AwcVlanIndex |
|
| A value used to index per-VLAN tables. Represents an IEEE 802.1Q VLAN-ID with global scope within a given bridged domain (see AwcVlanId textual convention). The value 4095 indicates that the conceptual row applies to non-VLAN-tagged frames (though it would be more directly representative of the packet format, 0 can not be used for this purpose, per SNMP conventions). |
| TEXTUAL-CONVENTION |
|
|
|
| |
Unsigned32 |
1..4095 |
|
| AwcVlanEncapType |
|
| The 802.1Q encapsulation mode. Valid values are: dot1qDisabled (1), Disabled dot1qPriority (2) 802.1Q Priority Tagging dot1qHybrid (3), 802.1Q VLAN Hybrid Trunk dot1qTrunk (4) 802.1Q VLAN Trunk The default value is normally Disabled. |
| TEXTUAL-CONVENTION |
|
|
|
| |
INTEGER |
dot1qDisabled(1), dot1qPriority(2), dot1qHybrid(3), dot1qTrunk(4) |
|
| AwcVlanCfgEntry |
|
| SEQUENCE |
|
|
|
| |
AwcVlanIndex as awcVlanIndex |
|
|
| |
AwcPolId as awcVlanPolId |
|
|
| |
TruthValue as awcVlanEnabled |
|
|
| |
INTEGER as awcVlanNUcastKeyRotationInterval |
|
|
| |
RowStatus as awcVlanRowStatus |
|
|
| |
AwcDot11MicAlgorithm as awcVlanMicAlgorithm |
|
|
| |
AwcDot11WEPKeyPermuteAlgorithm as awcVlanWEPKeyPermuteAlgorithm |
|
|
| |
OCTET STRING as awcVlanName |
|
|
| |
AwcPfPriority as awcVlanDefaultUserPriority |
|
|
| |
TruthValue as awcVlanAlert |
|
|
| AwcVlanNUcastKeyEntry |
|
| SEQUENCE |
|
|
|
| |
INTEGER as awcVlanNUcastKeyIndex |
|
|
| |
INTEGER as awcVlanNUcastKeyLen |
|
|
| |
WEPKeytype128 as awcVlanNUcastKeyValue |
|
|