
| SNMPv2-SMI | SNMPv2-TC | BAS-MIB |
| MODULE-IDENTITY | OBJECT-TYPE | Counter32 |
| Gauge32 | Integer32 | IpAddress |
| TEXTUAL-CONVENTION | TruthValue | RowStatus |
| basAliasOspf | BasChassisId | BasSlotId |
| BasInterfaceId | BasLogicalPortId |
| basOspf | 1.3.6.1.4.1.3493.2.7.7.1 | ||
| This module defines the MIB objects for a Broadband Access System IP Forwarding component. | |||
| MODULE-IDENTITY | |||
| basOspfObjects | 1.3.6.1.4.1.3493.2.7.7.1 | ||
| OBJECT IDENTIFIER | |||
| basOspfGeneralGroupTable | 1.3.6.1.4.1.3493.2.7.7.1.1 | ||
| A list of Route Server forwarding table distribution mechanism statistics. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| BasOspfGeneralGroupEntry | |||
| basOspfGeneralGroupEntry | 1.3.6.1.4.1.3493.2.7.7.1.1.1 | ||
| Objects for the CIDR mib. | |||
| OBJECT-TYPE | |||
| BasOspfGeneralGroupEntry | |||
| basOspfRouterId | 1.3.6.1.4.1.3493.2.7.7.1.1.1.1 | ||
| A 32-bit integer uniquely identifying the router in the Autonomous System. By convention, to ensure uniqueness, this should default to the value of one of the router's IP interface addresses. | |||
| OBJECT-TYPE | |||
| RouterID | |||
| basOspfAdminStat | 1.3.6.1.4.1.3493.2.7.7.1.1.1.2 | ||
| The administrative status of OSPF in the router. The value 'enabled' denotes that the OSPF Process is active on at least one inter- face; 'disabled' disables it on all inter- faces. | |||
| OBJECT-TYPE | |||
| Status | |||
| basOspfVersionNumber | 1.3.6.1.4.1.3493.2.7.7.1.1.1.3 | ||
| The current version number of the OSPF proto- col is 2. | |||
| OBJECT-TYPE | |||
| INTEGER | version2(2) | ||
| basOspfAreaBdrRtrStatus | 1.3.6.1.4.1.3493.2.7.7.1.1.1.4 | ||
| A flag to note whether this router is an area border router. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| basOspfASBdrRtrStatus | 1.3.6.1.4.1.3493.2.7.7.1.1.1.5 | ||
| A flag to note whether this router is config- ured as an Autonomous System border router. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| basOspfExternLsaCount | 1.3.6.1.4.1.3493.2.7.7.1.1.1.6 | ||
| The number of external (LS type 5) link-state advertisements in the link-state database. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| basOspfExternLsaCksumSum | 1.3.6.1.4.1.3493.2.7.7.1.1.1.7 | ||
| The 32-bit unsigned sum of the LS checksums of the external link-state advertisements con- tained in the link-state database. This sum can be used to determine if there has been a change in a router's link state database, and to compare the link-state database of two routers. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| basOspfTOSSupport | 1.3.6.1.4.1.3493.2.7.7.1.1.1.8 | ||
| The router's support for type-of-service rout- ing. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| basOspfOriginateNewLsas | 1.3.6.1.4.1.3493.2.7.7.1.1.1.9 | ||
| The number of new link-state advertisements that have been originated. This number is in- cremented each time the router originates a new LSA. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| basOspfRxNewLsas | 1.3.6.1.4.1.3493.2.7.7.1.1.1.10 | ||
| The number of link-state advertisements re- ceived determined to be new instantiations. This number does not include newer instantia- tions of self-originated link-state advertise- ments. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| basOspfExtLsdbLimit | 1.3.6.1.4.1.3493.2.7.7.1.1.1.11 | ||
| The maximum number of non-default AS- external-LSAs entries that can be stored in the link-state database. If the value is -1, then there is no limit. When the number of non-default AS-external-LSAs in a router's link-state database reaches ospfExtLsdbLimit, the router enters Overflow- State. The router never holds more than ospfExtLsdbLimit non-default AS-external-LSAs in its database. OspfExtLsdbLimit MUST be set identically in all routers attached to the OSPF backbone and/or any regular OSPF area. (i.e., OSPF stub areas and NSSAs are excluded). | |||
| OBJECT-TYPE | |||
| Integer32 | -1..'7FFFFFFF'h | ||
| basOspfMulticastExtensions | 1.3.6.1.4.1.3493.2.7.7.1.1.1.12 | ||
| A Bit Mask indicating whether the router is forwarding IP multicast (Class D) datagrams based on the algorithms defined in the Multi- cast Extensions to OSPF. Bit 0, if set, indicates that the router can forward IP multicast datagrams in the router's directly attached areas (called intra-area mul- ticast routing). Bit 1, if set, indicates that the router can forward IP multicast datagrams between OSPF areas (called inter-area multicast routing). Bit 2, if set, indicates that the router can forward IP multicast datagrams between Auto- nomous Systems (called inter-AS multicast rout- ing). Only certain combinations of bit settings are allowed, namely: 0 (no multicast forwarding is enabled), 1 (intra-area multicasting only), 3 (intra-area and inter-area multicasting), 5 (intra-area and inter-AS multicasting) and 7 (multicasting everywhere). By default, no mul- ticast forwarding is enabled. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| basOspfExitOverflowInterval | 1.3.6.1.4.1.3493.2.7.7.1.1.1.13 | ||
| The number of seconds that, after entering OverflowState, a router will attempt to leave OverflowState. This allows the router to again originate non-default AS-external-LSAs. When set to 0, the router will not leave Overflow- State until restarted. | |||
| OBJECT-TYPE | |||
| PositiveInteger | |||
| basOspfDemandExtensions | 1.3.6.1.4.1.3493.2.7.7.1.1.1.14 | ||
| The router's support for demand routing. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| basOspfGeneralGroupChassis | 1.3.6.1.4.1.3493.2.7.7.1.1.1.15 | ||
| The BAS Chassis ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasChassisId | |||
| basOspfGeneralGroupSlot | 1.3.6.1.4.1.3493.2.7.7.1.1.1.16 | ||
| The BAS Slot ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasSlotId | |||
| basOspfGeneralGroupIf | 1.3.6.1.4.1.3493.2.7.7.1.1.1.17 | ||
| The BAS interface ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasInterfaceId | |||
| basOspfGeneralGroupLPort | 1.3.6.1.4.1.3493.2.7.7.1.1.1.18 | ||
| The BAS logical port ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasLogicalPortId | |||
| basOspfAreaTable | 1.3.6.1.4.1.3493.2.7.7.1.2 | ||
| Information describing the configured parame- ters and cumulative statistics of the router's attached areas. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| BasOspfAreaEntry | |||
| basOspfAreaEntry | 1.3.6.1.4.1.3493.2.7.7.1.2.1 | ||
| Information describing the configured parame- ters and cumulative statistics of one of the router's attached areas. | |||
| OBJECT-TYPE | |||
| BasOspfAreaEntry | |||
| basOspfAreaId | 1.3.6.1.4.1.3493.2.7.7.1.2.1.1 | ||
| A 32-bit integer uniquely identifying an area. Area ID 0.0.0.0 is used for the OSPF backbone. | |||
| OBJECT-TYPE | |||
| AreaID | |||
| basOspfAuthType | 1.3.6.1.4.1.3493.2.7.7.1.2.1.2 | ||
| The authentication type specified for an area. Additional authentication types may be assigned locally on a per Area basis. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| basOspfImportAsExtern | 1.3.6.1.4.1.3493.2.7.7.1.2.1.3 | ||
| The area's support for importing AS external link- state advertisements. | |||
| OBJECT-TYPE | |||
| INTEGER | importExternal(1), importNoExternal(2), importNssa(3) | ||
| basOspfSpfRuns | 1.3.6.1.4.1.3493.2.7.7.1.2.1.4 | ||
| The number of times that the intra-area route table has been calculated using this area's link-state database. This is typically done using Dijkstra's algorithm. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| basOspfAreaBdrRtrCount | 1.3.6.1.4.1.3493.2.7.7.1.2.1.5 | ||
| The total number of area border routers reach- able within this area. This is initially zero, and is calculated in each SPF Pass. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| basOspfAsBdrRtrCount | 1.3.6.1.4.1.3493.2.7.7.1.2.1.6 | ||
| The total number of Autonomous System border routers reachable within this area. This is initially zero, and is calculated in each SPF Pass. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| basOspfAreaLsaCount | 1.3.6.1.4.1.3493.2.7.7.1.2.1.7 | ||
| The total number of link-state advertisements in this area's link-state database, excluding AS External LSA's. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| basOspfAreaLsaCksumSum | 1.3.6.1.4.1.3493.2.7.7.1.2.1.8 | ||
| The 32-bit unsigned sum of the link-state ad- vertisements' LS checksums contained in this area's link-state database. This sum excludes external (LS type 5) link-state advertisements. The sum can be used to determine if there has been a change in a router's link state data- base, and to compare the link-state database of two routers. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| basOspfAreaSummary | 1.3.6.1.4.1.3493.2.7.7.1.2.1.9 | ||
| The variable ospfAreaSummary controls the im- port of summary LSAs into stub areas. It has no effect on other areas. If it is noAreaSummary, the router will neither originate nor propagate summary LSAs into the stub area. It will rely entirely on its de- fault route. If it is sendAreaSummary, the router will both summarize and propagate summary LSAs. | |||
| OBJECT-TYPE | |||
| INTEGER | noAreaSummary(1), sendAreaSummary(2) | ||
| basOspfAreaStatus | 1.3.6.1.4.1.3493.2.7.7.1.2.1.10 | ||
| This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent. | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| basOspfAreaChassis | 1.3.6.1.4.1.3493.2.7.7.1.2.1.11 | ||
| The BAS Chassis ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasChassisId | |||
| basOspfAreaSlot | 1.3.6.1.4.1.3493.2.7.7.1.2.1.12 | ||
| The BAS Slot ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasSlotId | |||
| basOspfAreaIf | 1.3.6.1.4.1.3493.2.7.7.1.2.1.13 | ||
| The BAS interface ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasInterfaceId | |||
| basOspfAreaLPort | 1.3.6.1.4.1.3493.2.7.7.1.2.1.14 | ||
| The BAS logical port ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasLogicalPortId | |||
| basOspfStubAreaTable | 1.3.6.1.4.1.3493.2.7.7.1.3 | ||
| The set of metrics that will be advertised by a default Area Border Router into a stub area. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| BasOspfStubAreaEntry | |||
| basOspfStubAreaEntry | 1.3.6.1.4.1.3493.2.7.7.1.3.1 | ||
| The metric for a given Type of Service that will be advertised by a default Area Border Router into a stub area. | |||
| OBJECT-TYPE | |||
| BasOspfStubAreaEntry | |||
| basOspfStubAreaId | 1.3.6.1.4.1.3493.2.7.7.1.3.1.1 | ||
| The 32 bit identifier for the Stub Area. On creation, this can be derived from the in- stance. | |||
| OBJECT-TYPE | |||
| AreaID | |||
| basOspfStubTOS | 1.3.6.1.4.1.3493.2.7.7.1.3.1.2 | ||
| The Type of Service associated with the metric. On creation, this can be derived from the instance. | |||
| OBJECT-TYPE | |||
| TOSType | |||
| basOspfStubMetric | 1.3.6.1.4.1.3493.2.7.7.1.3.1.3 | ||
| The metric value applied at the indicated type of service. By default, this equals the least metric at the type of service among the inter- faces to other areas. | |||
| OBJECT-TYPE | |||
| BigMetric | |||
| basOspfStubStatus | 1.3.6.1.4.1.3493.2.7.7.1.3.1.4 | ||
| This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent. | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| basOspfStubMetricType | 1.3.6.1.4.1.3493.2.7.7.1.3.1.5 | ||
| This variable displays the type of metric ad- vertised as a default route. | |||
| OBJECT-TYPE | |||
| INTEGER | ospfMetric(1), comparableCost(2), nonComparable(3) | ||
| basOspfStubAreaChassis | 1.3.6.1.4.1.3493.2.7.7.1.3.1.6 | ||
| The BAS Chassis ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasChassisId | |||
| basOspfStubAreaSlot | 1.3.6.1.4.1.3493.2.7.7.1.3.1.7 | ||
| The BAS Slot ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasSlotId | |||
| basOspfStubAreaIf | 1.3.6.1.4.1.3493.2.7.7.1.3.1.8 | ||
| The BAS interface ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasInterfaceId | |||
| basOspfStubAreaLPort | 1.3.6.1.4.1.3493.2.7.7.1.3.1.9 | ||
| The BAS logical port ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasLogicalPortId | |||
| basOspfLsdbTable | 1.3.6.1.4.1.3493.2.7.7.1.4 | ||
| The OSPF Process's Link State Database. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| BasOspfLsdbEntry | |||
| basOspfLsdbEntry | 1.3.6.1.4.1.3493.2.7.7.1.4.1 | ||
| A single Link State Advertisement. | |||
| OBJECT-TYPE | |||
| BasOspfLsdbEntry | |||
| basOspfLsdbAreaId | 1.3.6.1.4.1.3493.2.7.7.1.4.1.1 | ||
| The 32 bit identifier of the Area from which the LSA was received. | |||
| OBJECT-TYPE | |||
| AreaID | |||
| basOspfLsdbType | 1.3.6.1.4.1.3493.2.7.7.1.4.1.2 | ||
| The type of the link state advertisement. Each link state type has a separate advertise- ment format. | |||
| OBJECT-TYPE | |||
| INTEGER | routerLink(1), networkLink(2), summaryLink(3), asSummaryLink(4), asExternalLink(5), multicastLink(6), nssaExternalLink(7) | ||
| basOspfLsdbLsid | 1.3.6.1.4.1.3493.2.7.7.1.4.1.3 | ||
| The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| basOspfLsdbRouterId | 1.3.6.1.4.1.3493.2.7.7.1.4.1.4 | ||
| The 32 bit number that uniquely identifies the originating router in the Autonomous System. | |||
| OBJECT-TYPE | |||
| RouterID | |||
| basOspfLsdbSequence | 1.3.6.1.4.1.3493.2.7.7.1.4.1.5 | ||
| The sequence number field is a signed 32-bit integer. It is used to detect old and dupli- cate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| basOspfLsdbAge | 1.3.6.1.4.1.3493.2.7.7.1.4.1.6 | ||
| This field is the age of the link state adver- tisement in seconds. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| basOspfLsdbChecksum | 1.3.6.1.4.1.3493.2.7.7.1.4.1.7 | ||
| This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connec- tionless datagrams; it is commonly referred to as the Fletcher checksum. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| basOspfLsdbAdvertisement | 1.3.6.1.4.1.3493.2.7.7.1.4.1.8 | ||
| The entire Link State Advertisement, including its header. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(1..65535) | ||
| basOspfLsdbChassis | 1.3.6.1.4.1.3493.2.7.7.1.4.1.9 | ||
| The BAS Chassis ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasChassisId | |||
| basOspfLsdbSlot | 1.3.6.1.4.1.3493.2.7.7.1.4.1.10 | ||
| The BAS Slot ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasSlotId | |||
| basOspfLsdbIf | 1.3.6.1.4.1.3493.2.7.7.1.4.1.11 | ||
| The BAS interface ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasInterfaceId | |||
| basOspfLsdbLPort | 1.3.6.1.4.1.3493.2.7.7.1.4.1.12 | ||
| The BAS logical port ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasLogicalPortId | |||
| basOspfHostTable | 1.3.6.1.4.1.3493.2.7.7.1.6 | ||
| The list of Hosts, and their metrics, that the router will advertise as host routes. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| BasOspfHostEntry | |||
| basOspfHostEntry | 1.3.6.1.4.1.3493.2.7.7.1.6.1 | ||
| A metric to be advertised, for a given type of service, when a given host is reachable. | |||
| OBJECT-TYPE | |||
| BasOspfHostEntry | |||
| basOspfHostIpAddress | 1.3.6.1.4.1.3493.2.7.7.1.6.1.1 | ||
| The IP Address of the Host. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| basOspfHostTOS | 1.3.6.1.4.1.3493.2.7.7.1.6.1.2 | ||
| The Type of Service of the route being config- ured. | |||
| OBJECT-TYPE | |||
| TOSType | |||
| basOspfHostMetric | 1.3.6.1.4.1.3493.2.7.7.1.6.1.3 | ||
| The Metric to be advertised. | |||
| OBJECT-TYPE | |||
| Metric | |||
| basOspfHostStatus | 1.3.6.1.4.1.3493.2.7.7.1.6.1.4 | ||
| This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent. | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| basOspfHostAreaID | 1.3.6.1.4.1.3493.2.7.7.1.6.1.5 | ||
| The Area the Host Entry is to be found within. By default, the area that a subsuming OSPF in- terface is in, or 0.0.0.0 | |||
| OBJECT-TYPE | |||
| AreaID | |||
| basOspfHostChassis | 1.3.6.1.4.1.3493.2.7.7.1.6.1.6 | ||
| The BAS Chassis ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasChassisId | |||
| basOspfHostSlot | 1.3.6.1.4.1.3493.2.7.7.1.6.1.7 | ||
| The BAS Slot ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasSlotId | |||
| basOspfHostIf | 1.3.6.1.4.1.3493.2.7.7.1.6.1.8 | ||
| The BAS interface ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasInterfaceId | |||
| basOspfHostLPort | 1.3.6.1.4.1.3493.2.7.7.1.6.1.9 | ||
| The BAS logical port ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasLogicalPortId | |||
| basOspfIfTable | 1.3.6.1.4.1.3493.2.7.7.1.7 | ||
| The OSPF Interface Table describes the inter- faces from the viewpoint of OSPF. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| BasOspfIfEntry | |||
| basOspfIfEntry | 1.3.6.1.4.1.3493.2.7.7.1.7.1 | ||
| The OSPF Interface Entry describes one inter- face from the viewpoint of OSPF. | |||
| OBJECT-TYPE | |||
| BasOspfIfEntry | |||
| basOspfIfIpAddress | 1.3.6.1.4.1.3493.2.7.7.1.7.1.1 | ||
| The IP address of this OSPF interface. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| basOspfAddressLessIf | 1.3.6.1.4.1.3493.2.7.7.1.7.1.2 | ||
| For the purpose of easing the instancing of addressed and addressless interfaces; This variable takes the value 0 on interfaces with IP Addresses, and the corresponding value of ifIndex for interfaces having no IP Address. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| basOspfIfAreaId | 1.3.6.1.4.1.3493.2.7.7.1.7.1.3 | ||
| A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0.0.0.0 is used for the OSPF backbone. | |||
| OBJECT-TYPE | |||
| AreaID | |||
| basOspfIfType | 1.3.6.1.4.1.3493.2.7.7.1.7.1.4 | ||
| The OSPF interface type. By way of a default, this field may be intuited from the corresponding value of ifType. Broad- cast LANs, such as Ethernet and IEEE 802.5, take the value 'broadcast', X.25 and similar technologies take the value 'nbma', and links that are definitively point to point take the value 'pointToPoint'. | |||
| OBJECT-TYPE | |||
| INTEGER | broadcast(1), nbma(2), pointToPoint(3), pointToMultipoint(5) | ||
| basOspfIfAdminStat | 1.3.6.1.4.1.3493.2.7.7.1.7.1.5 | ||
| The OSPF interface's administrative status. The value formed on the interface, and the in- terface will be advertised as an internal route to some area. The value 'disabled' denotes that the interface is external to OSPF. | |||
| OBJECT-TYPE | |||
| Status | |||
| basOspfIfRtrPriority | 1.3.6.1.4.1.3493.2.7.7.1.7.1.6 | ||
| The priority of this interface. Used in multi-access networks, this field is used in the designated router election algorithm. The value 0 signifies that the router is not eligi- ble to become the designated router on this particular network. In the event of a tie in this value, routers will use their Router ID as a tie breaker. | |||
| OBJECT-TYPE | |||
| DesignatedRouterPriority | |||
| basOspfIfTransitDelay | 1.3.6.1.4.1.3493.2.7.7.1.7.1.7 | ||
| The estimated number of seconds it takes to transmit a link state update packet over this interface. | |||
| OBJECT-TYPE | |||
| UpToMaxAge | |||
| basOspfIfRetransInterval | 1.3.6.1.4.1.3493.2.7.7.1.7.1.8 | ||
| The number of seconds between link-state ad- vertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database descrip- tion and link-state request packets. | |||
| OBJECT-TYPE | |||
| UpToMaxAge | |||
| basOspfIfHelloInterval | 1.3.6.1.4.1.3493.2.7.7.1.7.1.9 | ||
| The length of time, in seconds, between the Hello packets that the router sends on the in- terface. This value must be the same for all routers attached to a common network. | |||
| OBJECT-TYPE | |||
| HelloRange | |||
| basOspfIfRtrDeadInterval | 1.3.6.1.4.1.3493.2.7.7.1.7.1.10 | ||
| The number of seconds that a router's Hello packets have not been seen before it's neigh- bors declare the router down. This should be some multiple of the Hello interval. This value must be the same for all routers attached to a common network. | |||
| OBJECT-TYPE | |||
| PositiveInteger | |||
| basOspfIfPollInterval | 1.3.6.1.4.1.3493.2.7.7.1.7.1.11 | ||
| The larger time interval, in seconds, between the Hello packets sent to an inactive non- broadcast multi- access neighbor. | |||
| OBJECT-TYPE | |||
| PositiveInteger | |||
| basOspfIfState | 1.3.6.1.4.1.3493.2.7.7.1.7.1.12 | ||
| The OSPF Interface State. | |||
| OBJECT-TYPE | |||
| INTEGER | down(1), loopback(2), waiting(3), pointToPoint(4), designatedRouter(5), backupDesignatedRouter(6), otherDesignatedRouter(7) | ||
| basOspfIfDesignatedRouter | 1.3.6.1.4.1.3493.2.7.7.1.7.1.13 | ||
| The IP Address of the Designated Router. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| basOspfIfBackupDesignatedRouter | 1.3.6.1.4.1.3493.2.7.7.1.7.1.14 | ||
| The IP Address of the Backup Designated Router. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| basOspfIfEvents | 1.3.6.1.4.1.3493.2.7.7.1.7.1.15 | ||
| The number of times this OSPF interface has changed its state, or an error has occurred. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| basOspfIfAuthKey | 1.3.6.1.4.1.3493.2.7.7.1.7.1.16 | ||
| The Authentication Key. If the Area's Author- ization Type is simplePassword, and the key length is shorter than 8 octets, the agent will left adjust and zero fill to 8 octets. Note that unauthenticated interfaces need no authentication key, and simple password authen- tication cannot use a key of more than 8 oc- tets. Larger keys are useful only with authen- tication mechanisms not specified in this docu- ment. When read, ospfIfAuthKey always returns an Oc- tet String of length zero. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..256) | ||
| basOspfIfStatus | 1.3.6.1.4.1.3493.2.7.7.1.7.1.17 | ||
| This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent. | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| basOspfIfMulticastForwarding | 1.3.6.1.4.1.3493.2.7.7.1.7.1.18 | ||
| The way multicasts should forwarded on this interface; not forwarded, forwarded as data link multicasts, or forwarded as data link uni- casts. Data link multicasting is not meaning- ful on point to point and NBMA interfaces, and setting ospfMulticastForwarding to 0 effective- ly disables all multicast forwarding. | |||
| OBJECT-TYPE | |||
| INTEGER | blocked(1), multicast(2), unicast(3) | ||
| basOspfIfDemand | 1.3.6.1.4.1.3493.2.7.7.1.7.1.19 | ||
| Indicates whether Demand OSPF procedures (hel- lo supression to FULL neighbors and setting the DoNotAge flag on proogated LSAs) should be per- formed on this interface. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| basOspfIfAuthType | 1.3.6.1.4.1.3493.2.7.7.1.7.1.20 | ||
| The authentication type specified for an in- terface. Additional authentication types may be assigned locally. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..255 | ||
| basOspfIfChassis | 1.3.6.1.4.1.3493.2.7.7.1.7.1.21 | ||
| The BAS Chassis ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasChassisId | |||
| basOspfIfSlot | 1.3.6.1.4.1.3493.2.7.7.1.7.1.22 | ||
| The BAS Slot ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasSlotId | |||
| basOspfIfIf | 1.3.6.1.4.1.3493.2.7.7.1.7.1.23 | ||
| The BAS interface ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasInterfaceId | |||
| basOspfIfLPort | 1.3.6.1.4.1.3493.2.7.7.1.7.1.24 | ||
| The BAS logical port ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasLogicalPortId | |||
| basOspfIfMetricTable | 1.3.6.1.4.1.3493.2.7.7.1.8 | ||
| The TOS metrics for a non-virtual interface identified by the interface index. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| BasOspfIfMetricEntry | |||
| basOspfIfMetricEntry | 1.3.6.1.4.1.3493.2.7.7.1.8.1 | ||
| A particular TOS metric for a non-virtual in- terface identified by the interface index. | |||
| OBJECT-TYPE | |||
| BasOspfIfMetricEntry | |||
| basOspfIfMetricIpAddress | 1.3.6.1.4.1.3493.2.7.7.1.8.1.1 | ||
| The IP address of this OSPF interface. On row creation, this can be derived from the in- stance. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| basOspfIfMetricAddressLessIf | 1.3.6.1.4.1.3493.2.7.7.1.8.1.2 | ||
| For the purpose of easing the instancing of addressed and addressless interfaces; This variable takes the value 0 on interfaces with IP Addresses, and the value of ifIndex for in- terfaces having no IP Address. On row crea- tion, this can be derived from the instance. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| basOspfIfMetricTOS | 1.3.6.1.4.1.3493.2.7.7.1.8.1.3 | ||
| The type of service metric being referenced. On row creation, this can be derived from the instance. | |||
| OBJECT-TYPE | |||
| TOSType | |||
| basOspfIfMetricValue | 1.3.6.1.4.1.3493.2.7.7.1.8.1.4 | ||
| The metric of using this type of service on this interface. The default value of the TOS 0 Metric is 10^8 / ifSpeed. | |||
| OBJECT-TYPE | |||
| Metric | |||
| basOspfIfMetricStatus | 1.3.6.1.4.1.3493.2.7.7.1.8.1.5 | ||
| This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent. | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| basOspfIfMetricChassis | 1.3.6.1.4.1.3493.2.7.7.1.8.1.6 | ||
| The BAS Chassis ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasChassisId | |||
| basOspfIfMetricSlot | 1.3.6.1.4.1.3493.2.7.7.1.8.1.7 | ||
| The BAS Slot ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasSlotId | |||
| basOspfIfMetricIf | 1.3.6.1.4.1.3493.2.7.7.1.8.1.8 | ||
| The BAS interface ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasInterfaceId | |||
| basOspfIfMetricLPort | 1.3.6.1.4.1.3493.2.7.7.1.8.1.9 | ||
| The BAS logical port ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasLogicalPortId | |||
| basOspfVirtIfTable | 1.3.6.1.4.1.3493.2.7.7.1.9 | ||
| Information about this router's virtual inter- faces. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| BasOspfVirtIfEntry | |||
| basOspfVirtIfEntry | 1.3.6.1.4.1.3493.2.7.7.1.9.1 | ||
| Information about a single Virtual Interface. | |||
| OBJECT-TYPE | |||
| BasOspfVirtIfEntry | |||
| basOspfVirtIfAreaId | 1.3.6.1.4.1.3493.2.7.7.1.9.1.1 | ||
| The Transit Area that the Virtual Link traverses. By definition, this is not 0.0.0.0 | |||
| OBJECT-TYPE | |||
| AreaID | |||
| basOspfVirtIfNeighbor | 1.3.6.1.4.1.3493.2.7.7.1.9.1.2 | ||
| The Router ID of the Virtual Neighbor. | |||
| OBJECT-TYPE | |||
| RouterID | |||
| basOspfVirtIfTransitDelay | 1.3.6.1.4.1.3493.2.7.7.1.9.1.3 | ||
| The estimated number of seconds it takes to transmit a link- state update packet over this interface. | |||
| OBJECT-TYPE | |||
| UpToMaxAge | |||
| basOspfVirtIfRetransInterval | 1.3.6.1.4.1.3493.2.7.7.1.9.1.4 | ||
| The number of seconds between link-state ad- vertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database descrip- tion and link-state request packets. This value should be well over the expected round- trip time. | |||
| OBJECT-TYPE | |||
| UpToMaxAge | |||
| basOspfVirtIfHelloInterval | 1.3.6.1.4.1.3493.2.7.7.1.9.1.5 | ||
| The length of time, in seconds, between the Hello packets that the router sends on the in- terface. This value must be the same for the virtual neighbor. | |||
| OBJECT-TYPE | |||
| HelloRange | |||
| basOspfVirtIfRtrDeadInterval | 1.3.6.1.4.1.3493.2.7.7.1.9.1.6 | ||
| The number of seconds that a router's Hello packets have not been seen before it's neigh- bors declare the router down. This should be some multiple of the Hello interval. This value must be the same for the virtual neigh- bor. | |||
| OBJECT-TYPE | |||
| PositiveInteger | |||
| basOspfVirtIfState | 1.3.6.1.4.1.3493.2.7.7.1.9.1.7 | ||
| OSPF virtual interface states. | |||
| OBJECT-TYPE | |||
| INTEGER | down(1), pointToPoint(4) | ||
| basOspfVirtIfEvents | 1.3.6.1.4.1.3493.2.7.7.1.9.1.8 | ||
| The number of state changes or error events on this Virtual Link | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| basOspfVirtIfAuthKey | 1.3.6.1.4.1.3493.2.7.7.1.9.1.9 | ||
| If Authentication Type is simplePassword, the device will left adjust and zero fill to 8 oc- tets. Note that unauthenticated interfaces need no authentication key, and simple password authen- tication cannot use a key of more than 8 oc- tets. Larger keys are useful only with authen- tication mechanisms not specified in this docu- ment. When read, ospfVifAuthKey always returns a string of length zero. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..256) | ||
| basOspfVirtIfStatus | 1.3.6.1.4.1.3493.2.7.7.1.9.1.10 | ||
| This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent. | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| basOspfVirtIfAuthType | 1.3.6.1.4.1.3493.2.7.7.1.9.1.11 | ||
| The authentication type specified for a virtu- al interface. Additional authentication types may be assigned locally. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..255 | ||
| basOspfVirtIfChassis | 1.3.6.1.4.1.3493.2.7.7.1.9.1.12 | ||
| The BAS Chassis ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasChassisId | |||
| basOspfVirtIfSlot | 1.3.6.1.4.1.3493.2.7.7.1.9.1.13 | ||
| The BAS Slot ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasSlotId | |||
| basOspfVirtIfIf | 1.3.6.1.4.1.3493.2.7.7.1.9.1.14 | ||
| The BAS interface ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasInterfaceId | |||
| basOspfVirtIfLPort | 1.3.6.1.4.1.3493.2.7.7.1.9.1.15 | ||
| The BAS logical port ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasLogicalPortId | |||
| basOspfNbrTable | 1.3.6.1.4.1.3493.2.7.7.1.10 | ||
| A table of non-virtual neighbor information. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| BasOspfNbrEntry | |||
| basOspfNbrEntry | 1.3.6.1.4.1.3493.2.7.7.1.10.1 | ||
| The information regarding a single neighbor. | |||
| OBJECT-TYPE | |||
| BasOspfNbrEntry | |||
| basOspfNbrIpAddr | 1.3.6.1.4.1.3493.2.7.7.1.10.1.1 | ||
| The IP address this neighbor is using in its IP Source Address. Note that, on addressless links, this will not be 0.0.0.0, but the ad- dress of another of the neighbor's interfaces. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| basOspfNbrAddressLessIndex | 1.3.6.1.4.1.3493.2.7.7.1.10.1.2 | ||
| On an interface having an IP Address, zero. On addressless interfaces, the corresponding value of ifIndex in the Internet Standard MIB. On row creation, this can be derived from the instance. | |||
| OBJECT-TYPE | |||
| InterfaceIndex | |||
| basOspfNbrRtrId | 1.3.6.1.4.1.3493.2.7.7.1.10.1.3 | ||
| A 32-bit integer (represented as a type IpAd- dress) uniquely identifying the neighboring router in the Autonomous System. | |||
| OBJECT-TYPE | |||
| RouterID | |||
| basOspfNbrOptions | 1.3.6.1.4.1.3493.2.7.7.1.10.1.4 | ||
| A Bit Mask corresponding to the neighbor's op- tions field. Bit 0, if set, indicates that the system will operate on Type of Service metrics other than TOS 0. If zero, the neighbor will ignore all metrics except the TOS 0 metric. Bit 1, if set, indicates that the associated area accepts and operates on external informa- tion; if zero, it is a stub area. Bit 2, if set, indicates that the system is ca- pable of routing IP Multicast datagrams; i.e., that it implements the Multicast Extensions to OSPF. Bit 3, if set, indicates that the associated area is an NSSA. These areas are capable of carrying type 7 external advertisements, which are translated into type 5 external advertise- ments at NSSA borders. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| basOspfNbrPriority | 1.3.6.1.4.1.3493.2.7.7.1.10.1.5 | ||
| The priority of this neighbor in the designat- ed router election algorithm. The value 0 sig- nifies that the neighbor is not eligible to be- come the designated router on this particular network. | |||
| OBJECT-TYPE | |||
| DesignatedRouterPriority | |||
| basOspfNbrState | 1.3.6.1.4.1.3493.2.7.7.1.10.1.6 | ||
| The State of the relationship with this Neigh- bor. | |||
| OBJECT-TYPE | |||
| INTEGER | down(1), attempt(2), init(3), twoWay(4), exchangeStart(5), exchange(6), loading(7), full(8) | ||
| basOspfNbrEvents | 1.3.6.1.4.1.3493.2.7.7.1.10.1.7 | ||
| The number of times this neighbor relationship has changed state, or an error has occurred. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| basOspfNbrLsRetransQLen | 1.3.6.1.4.1.3493.2.7.7.1.10.1.8 | ||
| The current length of the retransmission queue. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| basOspfNbmaNbrStatus | 1.3.6.1.4.1.3493.2.7.7.1.10.1.9 | ||
| This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent. | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| basOspfNbmaNbrPermanence | 1.3.6.1.4.1.3493.2.7.7.1.10.1.10 | ||
| This variable displays the status of the en- try. 'dynamic' and 'permanent' refer to how the neighbor became known. | |||
| OBJECT-TYPE | |||
| INTEGER | dynamic(1), permanent(2) | ||
| basOspfNbrHelloSuppressed | 1.3.6.1.4.1.3493.2.7.7.1.10.1.11 | ||
| Indicates whether Hellos are being suppressed to the neighbor | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| basOspfNbrChassis | 1.3.6.1.4.1.3493.2.7.7.1.10.1.12 | ||
| The BAS Chassis ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasChassisId | |||
| basOspfNbrSlot | 1.3.6.1.4.1.3493.2.7.7.1.10.1.13 | ||
| The BAS Slot ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasSlotId | |||
| basOspfNbrIf | 1.3.6.1.4.1.3493.2.7.7.1.10.1.14 | ||
| The BAS interface ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasInterfaceId | |||
| basOspfNbrLPort | 1.3.6.1.4.1.3493.2.7.7.1.10.1.15 | ||
| The BAS logical port ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasLogicalPortId | |||
| basOspfVirtNbrTable | 1.3.6.1.4.1.3493.2.7.7.1.11 | ||
| A table of virtual neighbor information. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| BasOspfVirtNbrEntry | |||
| basOspfVirtNbrEntry | 1.3.6.1.4.1.3493.2.7.7.1.11.1 | ||
| Virtual neighbor information. | |||
| OBJECT-TYPE | |||
| BasOspfVirtNbrEntry | |||
| basOspfVirtNbrArea | 1.3.6.1.4.1.3493.2.7.7.1.11.1.1 | ||
| The Transit Area Identifier. | |||
| OBJECT-TYPE | |||
| AreaID | |||
| basOspfVirtNbrRtrId | 1.3.6.1.4.1.3493.2.7.7.1.11.1.2 | ||
| A 32-bit integer uniquely identifying the neighboring router in the Autonomous System. | |||
| OBJECT-TYPE | |||
| RouterID | |||
| basOspfVirtNbrIpAddr | 1.3.6.1.4.1.3493.2.7.7.1.11.1.3 | ||
| The IP address this Virtual Neighbor is us- ing. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| basOspfVirtNbrOptions | 1.3.6.1.4.1.3493.2.7.7.1.11.1.4 | ||
| A Bit Mask corresponding to the neighbor's op- tions field. Bit 1, if set, indicates that the system will operate on Type of Service metrics other than TOS 0. If zero, the neighbor will ignore all metrics except the TOS 0 metric. Bit 2, if set, indicates that the system is Network Multicast capable; ie, that it imple- ments OSPF Multicast Routing. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| basOspfVirtNbrState | 1.3.6.1.4.1.3493.2.7.7.1.11.1.5 | ||
| The state of the Virtual Neighbor Relation- ship. | |||
| OBJECT-TYPE | |||
| INTEGER | down(1), attempt(2), init(3), twoWay(4), exchangeStart(5), exchange(6), loading(7), full(8) | ||
| basOspfVirtNbrEvents | 1.3.6.1.4.1.3493.2.7.7.1.11.1.6 | ||
| The number of times this virtual link has changed its state, or an error has occurred. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| basOspfVirtNbrLsRetransQLen | 1.3.6.1.4.1.3493.2.7.7.1.11.1.7 | ||
| The current length of the retransmission queue. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| basOspfVirtNbrHelloSuppressed | 1.3.6.1.4.1.3493.2.7.7.1.11.1.8 | ||
| Indicates whether Hellos are being suppressed to the neighbor | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| basOspfVirtNbrChassis | 1.3.6.1.4.1.3493.2.7.7.1.11.1.9 | ||
| The BAS Chassis ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasChassisId | |||
| basOspfVirtNbrSlot | 1.3.6.1.4.1.3493.2.7.7.1.11.1.10 | ||
| The BAS Slot ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasSlotId | |||
| basOspfVirtNbrIf | 1.3.6.1.4.1.3493.2.7.7.1.11.1.11 | ||
| The BAS interface ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasInterfaceId | |||
| basOspfVirtNbrLPort | 1.3.6.1.4.1.3493.2.7.7.1.11.1.12 | ||
| The BAS logical port ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasLogicalPortId | |||
| basOspfExtLsdbTable | 1.3.6.1.4.1.3493.2.7.7.1.12 | ||
| The OSPF Process's Links State Database. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| BasOspfExtLsdbEntry | |||
| basOspfExtLsdbEntry | 1.3.6.1.4.1.3493.2.7.7.1.12.1 | ||
| A single Link State Advertisement. | |||
| OBJECT-TYPE | |||
| BasOspfExtLsdbEntry | |||
| basOspfExtLsdbType | 1.3.6.1.4.1.3493.2.7.7.1.12.1.1 | ||
| The type of the link state advertisement. Each link state type has a separate advertise- ment format. | |||
| OBJECT-TYPE | |||
| INTEGER | asExternalLink(5) | ||
| basOspfExtLsdbLsid | 1.3.6.1.4.1.3493.2.7.7.1.12.1.2 | ||
| The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| basOspfExtLsdbRouterId | 1.3.6.1.4.1.3493.2.7.7.1.12.1.3 | ||
| The 32 bit number that uniquely identifies the originating router in the Autonomous System. | |||
| OBJECT-TYPE | |||
| RouterID | |||
| basOspfExtLsdbSequence | 1.3.6.1.4.1.3493.2.7.7.1.12.1.4 | ||
| The sequence number field is a signed 32-bit integer. It is used to detect old and dupli- cate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| basOspfExtLsdbAge | 1.3.6.1.4.1.3493.2.7.7.1.12.1.5 | ||
| This field is the age of the link state adver- tisement in seconds. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| basOspfExtLsdbChecksum | 1.3.6.1.4.1.3493.2.7.7.1.12.1.6 | ||
| This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connec- tionless datagrams; it is commonly referred to as the Fletcher checksum. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| basOspfExtLsdbAdvertisement | 1.3.6.1.4.1.3493.2.7.7.1.12.1.7 | ||
| The entire Link State Advertisement, including its header. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(36) | ||
| basOspfExtLsdbChassis | 1.3.6.1.4.1.3493.2.7.7.1.12.1.8 | ||
| The BAS Chassis ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasChassisId | |||
| basOspfExtLsdbSlot | 1.3.6.1.4.1.3493.2.7.7.1.12.1.9 | ||
| The BAS Slot ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasSlotId | |||
| basOspfExtLsdbIf | 1.3.6.1.4.1.3493.2.7.7.1.12.1.10 | ||
| The BAS interface ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasInterfaceId | |||
| basOspfExtLsdbLPort | 1.3.6.1.4.1.3493.2.7.7.1.12.1.11 | ||
| The BAS logical port ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasLogicalPortId | |||
| basOspfRouteGroup | 1.3.6.1.4.1.3493.2.7.7.1.13 | ||
| OBJECT IDENTIFIER | |||
| basOspfIntraArea | 1.3.6.1.4.1.3493.2.7.7.1.13.1 | ||
| OBJECT IDENTIFIER | |||
| basOspfInterArea | 1.3.6.1.4.1.3493.2.7.7.1.13.2 | ||
| OBJECT IDENTIFIER | |||
| basOspfExternalType1 | 1.3.6.1.4.1.3493.2.7.7.1.13.3 | ||
| OBJECT IDENTIFIER | |||
| basOspfExternalType2 | 1.3.6.1.4.1.3493.2.7.7.1.13.4 | ||
| OBJECT IDENTIFIER | |||
| basOspfAreaAggregateTable | 1.3.6.1.4.1.3493.2.7.7.1.14 | ||
| A range of IP addresses specified by an IP address/IP network mask pair. For example, class B address range of X.X.X.X with a network mask of 255.255.0.0 includes all IP addresses from X.X.0.0 to X.X.255.255. Note that if ranges are configured such that one range sub- sumes another range (e.g., 10.0.0.0 mask 255.0.0.0 and 10.1.0.0 mask 255.255.0.0), the most specific match is the preferred one. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| BasOspfAreaAggregateEntry | |||
| basOspfAreaAggregateEntry | 1.3.6.1.4.1.3493.2.7.7.1.14.1 | ||
| A range of IP addresses specified by an IP address/IP network mask pair. For example, class B address range of X.X.X.X with a network mask of 255.255.0.0 includes all IP addresses from X.X.0.0 to X.X.255.255. Note that if ranges are range configured such that one range subsumes another range (e.g., 10.0.0.0 mask 255.0.0.0 and 10.1.0.0 mask 255.255.0.0), the most specific match is the preferred one. | |||
| OBJECT-TYPE | |||
| BasOspfAreaAggregateEntry | |||
| basOspfAreaAggregateAreaID | 1.3.6.1.4.1.3493.2.7.7.1.14.1.1 | ||
| The Area the Address Aggregate is to be found within. | |||
| OBJECT-TYPE | |||
| AreaID | |||
| basOspfAreaAggregateLsdbType | 1.3.6.1.4.1.3493.2.7.7.1.14.1.2 | ||
| The type of the Address Aggregate. This field specifies the Lsdb type that this Address Ag- gregate applies to. | |||
| OBJECT-TYPE | |||
| INTEGER | summaryLink(3), nssaExternalLink(7) | ||
| basOspfAreaAggregateNet | 1.3.6.1.4.1.3493.2.7.7.1.14.1.3 | ||
| The IP Address of the Net or Subnet indicated by the range. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| basOspfAreaAggregateMask | 1.3.6.1.4.1.3493.2.7.7.1.14.1.4 | ||
| The Subnet Mask that pertains to the Net or Subnet. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| basOspfAreaAggregateStatus | 1.3.6.1.4.1.3493.2.7.7.1.14.1.5 | ||
| This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent. | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| basOspfAreaAggregateEffect | 1.3.6.1.4.1.3493.2.7.7.1.14.1.6 | ||
| Subnets subsumed by ranges either trigger the advertisement of the indicated aggregate (ad- vertiseMatching), or result in the subnet's not being advertised at all outside the area. | |||
| OBJECT-TYPE | |||
| INTEGER | advertiseMatching(1), doNotAdvertiseMatching(2) | ||
| basOspfAreaAggregateChassis | 1.3.6.1.4.1.3493.2.7.7.1.14.1.7 | ||
| The BAS Chassis ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasChassisId | |||
| basOspfAreaAggregateSlot | 1.3.6.1.4.1.3493.2.7.7.1.14.1.8 | ||
| The BAS Slot ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasSlotId | |||
| basOspfAreaAggregateIf | 1.3.6.1.4.1.3493.2.7.7.1.14.1.9 | ||
| The BAS interface ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasInterfaceId | |||
| basOspfAreaAggregateLPort | 1.3.6.1.4.1.3493.2.7.7.1.14.1.10 | ||
| The BAS logical port ID of the Route Server. | |||
| OBJECT-TYPE | |||
| BasLogicalPortId | |||
| AreaID | |||
| An OSPF Area Identifier. | |||
| TEXTUAL-CONVENTION | |||
| IpAddress | |||
| RouterID | |||
| A OSPF Router Identifier. | |||
| TEXTUAL-CONVENTION | |||
| IpAddress | |||
| Metric | |||
| The OSPF Internal Metric. | |||
| TEXTUAL-CONVENTION | |||
| Integer32 | 0..'FFFF'h | ||
| BigMetric | |||
| The OSPF External Metric. | |||
| TEXTUAL-CONVENTION | |||
| Integer32 | 0..'FFFFFF'h | ||
| Status | |||
| The status of an interface: 'enabled' indicates that it is willing to communicate with other OSPF Routers, while 'disabled' indicates that it is not. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | enabled(1), disabled(2) | ||
| PositiveInteger | |||
| A positive integer. Values in excess are precluded as unnecessary and prone to interoperability issues. | |||
| TEXTUAL-CONVENTION | |||
| Integer32 | 0..'7FFFFFFF'h | ||
| HelloRange | |||
| The range of intervals on which hello messages are exchanged. | |||
| TEXTUAL-CONVENTION | |||
| Integer32 | 1..'FFFF'h | ||
| UpToMaxAge | |||
| The values that one might find or configure for variables bounded by the maximum age of an LSA. | |||
| TEXTUAL-CONVENTION | |||
| Integer32 | 0..3600 | ||
| InterfaceIndex | |||
| The range of ifIndex. | |||
| TEXTUAL-CONVENTION | |||
| Integer32 | |||
| DesignatedRouterPriority | |||
| The values defined for the priority of a system for becoming the designated router. | |||
| TEXTUAL-CONVENTION | |||
| Integer32 | 0..'FF'h | ||
| TOSType | |||
| Type of Service is defined as a mapping to the IP Type of Service Flags as defined in the IP Forwarding Table MIB +-----+-----+-----+-----+-----+-----+-----+-----+ | | | | | PRECEDENCE | TYPE OF SERVICE | 0 | | | | | +-----+-----+-----+-----+-----+-----+-----+-----+ IP TOS IP TOS Field Policy Field Policy Contents Code Contents Code 0 0 0 0 ==> 0 0 0 0 1 ==> 2 0 0 1 0 ==> 4 0 0 1 1 ==> 6 0 1 0 0 ==> 8 0 1 0 1 ==> 10 0 1 1 0 ==> 12 0 1 1 1 ==> 14 1 0 0 0 ==> 16 1 0 0 1 ==> 18 1 0 1 0 ==> 20 1 0 1 1 ==> 22 1 1 0 0 ==> 24 1 1 0 1 ==> 26 1 1 1 0 ==> 28 1 1 1 1 ==> 30 The remaining values are left for future definition. | |||
| TEXTUAL-CONVENTION | |||
| Integer32 | 0..30 | ||
| BasOspfGeneralGroupEntry | |||
| SEQUENCE | |||
| RouterID as basOspfRouterId | |||
| Status as basOspfAdminStat | |||
| INTEGER as basOspfVersionNumber | |||
| TruthValue as basOspfAreaBdrRtrStatus | |||
| TruthValue as basOspfASBdrRtrStatus | |||
| Gauge32 as basOspfExternLsaCount | |||
| Integer32 as basOspfExternLsaCksumSum | |||
| TruthValue as basOspfTOSSupport | |||
| Counter32 as basOspfOriginateNewLsas | |||
| Counter32 as basOspfRxNewLsas | |||
| Integer32 as basOspfExtLsdbLimit | |||
| Integer32 as basOspfMulticastExtensions | |||
| PositiveInteger as basOspfExitOverflowInterval | |||
| TruthValue as basOspfDemandExtensions | |||
| BasChassisId as basOspfGeneralGroupChassis | |||
| BasSlotId as basOspfGeneralGroupSlot | |||
| BasInterfaceId as basOspfGeneralGroupIf | |||
| BasLogicalPortId as basOspfGeneralGroupLPort | |||
| BasOspfAreaEntry | |||
| SEQUENCE | |||
| AreaID as basOspfAreaId | |||
| Integer32 as basOspfAuthType | |||
| INTEGER as basOspfImportAsExtern | |||
| Counter32 as basOspfSpfRuns | |||
| Gauge32 as basOspfAreaBdrRtrCount | |||
| Gauge32 as basOspfAsBdrRtrCount | |||
| Gauge32 as basOspfAreaLsaCount | |||
| Integer32 as basOspfAreaLsaCksumSum | |||
| INTEGER as basOspfAreaSummary | |||
| RowStatus as basOspfAreaStatus | |||
| BasChassisId as basOspfAreaChassis | |||
| BasSlotId as basOspfAreaSlot | |||
| BasInterfaceId as basOspfAreaIf | |||
| BasLogicalPortId as basOspfAreaLPort | |||
| BasOspfStubAreaEntry | |||
| SEQUENCE | |||
| AreaID as basOspfStubAreaId | |||
| TOSType as basOspfStubTOS | |||
| BigMetric as basOspfStubMetric | |||
| RowStatus as basOspfStubStatus | |||
| INTEGER as basOspfStubMetricType | |||
| BasChassisId as basOspfStubAreaChassis | |||
| BasSlotId as basOspfStubAreaSlot | |||
| BasInterfaceId as basOspfStubAreaIf | |||
| BasLogicalPortId as basOspfStubAreaLPort | |||
| BasOspfLsdbEntry | |||
| SEQUENCE | |||
| AreaID as basOspfLsdbAreaId | |||
| INTEGER as basOspfLsdbType | |||
| IpAddress as basOspfLsdbLsid | |||
| RouterID as basOspfLsdbRouterId | |||
| Integer32 as basOspfLsdbSequence | |||
| Integer32 as basOspfLsdbAge | |||
| Integer32 as basOspfLsdbChecksum | |||
| OCTET STRING as basOspfLsdbAdvertisement | |||
| BasChassisId as basOspfLsdbChassis | |||
| BasSlotId as basOspfLsdbSlot | |||
| BasInterfaceId as basOspfLsdbIf | |||
| BasLogicalPortId as basOspfLsdbLPort | |||
| BasOspfHostEntry | |||
| SEQUENCE | |||
| IpAddress as basOspfHostIpAddress | |||
| TOSType as basOspfHostTOS | |||
| Metric as basOspfHostMetric | |||
| RowStatus as basOspfHostStatus | |||
| AreaID as basOspfHostAreaID | |||
| BasChassisId as basOspfHostChassis | |||
| BasSlotId as basOspfHostSlot | |||
| BasInterfaceId as basOspfHostIf | |||
| BasLogicalPortId as basOspfHostLPort | |||
| BasOspfIfEntry | |||
| SEQUENCE | |||
| IpAddress as basOspfIfIpAddress | |||
| Integer32 as basOspfAddressLessIf | |||
| AreaID as basOspfIfAreaId | |||
| INTEGER as basOspfIfType | |||
| Status as basOspfIfAdminStat | |||
| DesignatedRouterPriority as basOspfIfRtrPriority | |||
| UpToMaxAge as basOspfIfTransitDelay | |||
| UpToMaxAge as basOspfIfRetransInterval | |||
| HelloRange as basOspfIfHelloInterval | |||
| PositiveInteger as basOspfIfRtrDeadInterval | |||
| PositiveInteger as basOspfIfPollInterval | |||
| INTEGER as basOspfIfState | |||
| IpAddress as basOspfIfDesignatedRouter | |||
| IpAddress as basOspfIfBackupDesignatedRouter | |||
| Counter32 as basOspfIfEvents | |||
| INTEGER as basOspfIfAuthType | |||
| OCTET STRING as basOspfIfAuthKey | |||
| RowStatus as basOspfIfStatus | |||
| INTEGER as basOspfIfMulticastForwarding | |||
| TruthValue as basOspfIfDemand | |||
| BasChassisId as basOspfIfChassis | |||
| BasSlotId as basOspfIfSlot | |||
| BasInterfaceId as basOspfIfIf | |||
| BasLogicalPortId as basOspfIfLPort | |||
| BasOspfIfMetricEntry | |||
| SEQUENCE | |||
| IpAddress as basOspfIfMetricIpAddress | |||
| Integer32 as basOspfIfMetricAddressLessIf | |||
| TOSType as basOspfIfMetricTOS | |||
| Metric as basOspfIfMetricValue | |||
| RowStatus as basOspfIfMetricStatus | |||
| BasChassisId as basOspfIfMetricChassis | |||
| BasSlotId as basOspfIfMetricSlot | |||
| BasInterfaceId as basOspfIfMetricIf | |||
| BasLogicalPortId as basOspfIfMetricLPort | |||
| BasOspfVirtIfEntry | |||
| SEQUENCE | |||
| AreaID as basOspfVirtIfAreaId | |||
| RouterID as basOspfVirtIfNeighbor | |||
| UpToMaxAge as basOspfVirtIfTransitDelay | |||
| UpToMaxAge as basOspfVirtIfRetransInterval | |||
| HelloRange as basOspfVirtIfHelloInterval | |||
| PositiveInteger as basOspfVirtIfRtrDeadInterval | |||
| INTEGER as basOspfVirtIfState | |||
| Counter32 as basOspfVirtIfEvents | |||
| INTEGER as basOspfVirtIfAuthType | |||
| OCTET STRING as basOspfVirtIfAuthKey | |||
| RowStatus as basOspfVirtIfStatus | |||
| BasChassisId as basOspfVirtIfChassis | |||
| BasSlotId as basOspfVirtIfSlot | |||
| BasInterfaceId as basOspfVirtIfIf | |||
| BasLogicalPortId as basOspfVirtIfLPort | |||
| BasOspfNbrEntry | |||
| SEQUENCE | |||
| IpAddress as basOspfNbrIpAddr | |||
| InterfaceIndex as basOspfNbrAddressLessIndex | |||
| RouterID as basOspfNbrRtrId | |||
| Integer32 as basOspfNbrOptions | |||
| DesignatedRouterPriority as basOspfNbrPriority | |||
| INTEGER as basOspfNbrState | |||
| Counter32 as basOspfNbrEvents | |||
| Gauge32 as basOspfNbrLsRetransQLen | |||
| RowStatus as basOspfNbmaNbrStatus | |||
| INTEGER as basOspfNbmaNbrPermanence | |||
| TruthValue as basOspfNbrHelloSuppressed | |||
| BasChassisId as basOspfNbrChassis | |||
| BasSlotId as basOspfNbrSlot | |||
| BasInterfaceId as basOspfNbrIf | |||
| BasLogicalPortId as basOspfNbrLPort | |||
| BasOspfVirtNbrEntry | |||
| SEQUENCE | |||
| AreaID as basOspfVirtNbrArea | |||
| RouterID as basOspfVirtNbrRtrId | |||
| IpAddress as basOspfVirtNbrIpAddr | |||
| Integer32 as basOspfVirtNbrOptions | |||
| INTEGER as basOspfVirtNbrState | |||
| Counter32 as basOspfVirtNbrEvents | |||
| Gauge32 as basOspfVirtNbrLsRetransQLen | |||
| TruthValue as basOspfVirtNbrHelloSuppressed | |||
| BasChassisId as basOspfVirtNbrChassis | |||
| BasSlotId as basOspfVirtNbrSlot | |||
| BasInterfaceId as basOspfVirtNbrIf | |||
| BasLogicalPortId as basOspfVirtNbrLPort | |||
| BasOspfExtLsdbEntry | |||
| SEQUENCE | |||
| INTEGER as basOspfExtLsdbType | |||
| IpAddress as basOspfExtLsdbLsid | |||
| RouterID as basOspfExtLsdbRouterId | |||
| Integer32 as basOspfExtLsdbSequence | |||
| Integer32 as basOspfExtLsdbAge | |||
| Integer32 as basOspfExtLsdbChecksum | |||
| OCTET STRING as basOspfExtLsdbAdvertisement | |||
| BasChassisId as basOspfExtLsdbChassis | |||
| BasSlotId as basOspfExtLsdbSlot | |||
| BasInterfaceId as basOspfExtLsdbIf | |||
| BasLogicalPortId as basOspfExtLsdbLPort | |||
| BasOspfAreaAggregateEntry | |||
| SEQUENCE | |||
| AreaID as basOspfAreaAggregateAreaID | |||
| INTEGER as basOspfAreaAggregateLsdbType | |||
| IpAddress as basOspfAreaAggregateNet | |||
| IpAddress as basOspfAreaAggregateMask | |||
| RowStatus as basOspfAreaAggregateStatus | |||
| INTEGER as basOspfAreaAggregateEffect | |||
| BasChassisId as basOspfAreaAggregateChassis | |||
| BasSlotId as basOspfAreaAggregateSlot | |||
| BasInterfaceId as basOspfAreaAggregateIf | |||
| BasLogicalPortId as basOspfAreaAggregateLPort | |||