
| RFC1155-SMI | RFC-1212 |
| Counter | OBJECT-TYPE |
| org | 1.3 | ||
| OBJECT IDENTIFIER | |||
| dod | 1.3.6 | ||
| OBJECT IDENTIFIER | |||
| internet | 1.3.6.1 | ||
| OBJECT IDENTIFIER | |||
| private | 1.3.6.1.4 | ||
| OBJECT IDENTIFIER | |||
| enterprises | 1.3.6.1.4.1 | ||
| OBJECT IDENTIFIER | |||
| bintec | 1.3.6.1.4.1.272 | ||
| OBJECT IDENTIFIER | |||
| bibo | 1.3.6.1.4.1.272.4 | ||
| OBJECT IDENTIFIER | |||
| x21 | 1.3.6.1.4.1.272.4.10 | ||
| OBJECT IDENTIFIER | |||
| x21IfTable | 1.3.6.1.4.1.272.4.10.1 | ||
| The x21IfTable contains information relating to the interfaces found on the system. Each entry corresponds to a connected X21 interface. Entries can only be added or deleted by the system. Creating entries: Entries are created by the system only when a new X21 module is installed. Deleting entries: Entries are removed by the system after the appropriate X21 module is removed. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| X21IfEntry | |||
| x21IfEntry | 1.3.6.1.4.1.272.4.10.1.1 | ||
| OBJECT-TYPE | |||
| X21IfEntry | |||
| x21IfIndex | 1.3.6.1.4.1.272.4.10.1.1.1 | ||
| Unique index of the X21 interface. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| x21IfL1State | 1.3.6.1.4.1.272.4.10.1.1.2 | ||
| The X21 physical layer state dn(1) physical layer is inactive; up(2) physical layer is active; | |||
| OBJECT-TYPE | |||
| INTEGER | dn(1), up(2) | ||
| x21IfL1Mode | 1.3.6.1.4.1.272.4.10.1.1.3 | ||
| The physical layer (layer 1) mode. When configured as DCE(2) the X21 interface provides the clock. | |||
| OBJECT-TYPE | |||
| INTEGER | dte(1), dce(2) | ||
| x21IfIfLeads | 1.3.6.1.4.1.272.4.10.1.1.4 | ||
| The value of IfLeads has influence on the state of the physical layer (L1State). When configured as IfLeads=enabled(1), the state of the physical layer depends on the signals of the X.21 interface pins `Indication' and `Control'. When configured as IfLeads=disabled(2), the state of the physical layer stays always up. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| x21IfSpeed | 1.3.6.1.4.1.272.4.10.1.1.5 | ||
| The X21 interface speed in bits per second. The range can be configured between 2Mbits and 2400 Bits per second. | |||
| OBJECT-TYPE | |||
| INTEGER | s2048k(1), s1024k(2), s512k(3), s256k(4), s128k(5), s64000(6), s38400(7), s19200(8), s14400(9), s9600(10), s2400(11) | ||
| x21IfL2Mode | 1.3.6.1.4.1.272.4.10.1.1.6 | ||
| The layer 2 mode. This value has influence on the HDLC address field (first byte of a HDCL frame). When configured as DTE(1) the address in a command frame is 0x01, when configured as DCE(2) it is 0x03. For response frames it is vice versa. When configured as AUTO(3), layer 2 is set to the same mode like L1Mode is set. | |||
| OBJECT-TYPE | |||
| INTEGER | dte(1), dce(2), auto(3) | ||
| x21IfSpeedReal | 1.3.6.1.4.1.272.4.10.1.1.7 | ||
| The measured X21 interface speed in bits per second. | |||
| OBJECT-TYPE | |||
| Counter | |||
| x21IfRxPackets | 1.3.6.1.4.1.272.4.10.1.1.8 | ||
| Count of received valid Frames. | |||
| OBJECT-TYPE | |||
| Counter | |||
| x21IfRxOctets | 1.3.6.1.4.1.272.4.10.1.1.9 | ||
| Count of received bytes. | |||
| OBJECT-TYPE | |||
| Counter | |||
| x21IfTxPackets | 1.3.6.1.4.1.272.4.10.1.1.10 | ||
| Count of transmitted valid Frames. | |||
| OBJECT-TYPE | |||
| Counter | |||
| x21IfTxOctets | 1.3.6.1.4.1.272.4.10.1.1.11 | ||
| Count of transmitted bytes. | |||
| OBJECT-TYPE | |||
| Counter | |||
| x21IfRxResets | 1.3.6.1.4.1.272.4.10.1.1.12 | ||
| Count of receiver resets. Under rare circumstances it might be necessary to reset the receiver to work properly. | |||
| OBJECT-TYPE | |||
| Counter | |||
| x21IfRxAborts | 1.3.6.1.4.1.272.4.10.1.1.13 | ||
| Count of receiver aborts. The sender of a frame can indicate a frame as aborted with a special Abort sequence. | |||
| OBJECT-TYPE | |||
| Counter | |||
| x21IfRxOverruns | 1.3.6.1.4.1.272.4.10.1.1.14 | ||
| Count of receiver overruns. If the X21 card is unable to grant sufficiently soon/often the bus, the 32-character RxFIFO may fill up. This leads to loss of data. | |||
| OBJECT-TYPE | |||
| Counter | |||
| x21IfRxCRCErrors | 1.3.6.1.4.1.272.4.10.1.1.15 | ||
| Count of corrupted frames. Errors due to interference on the X21 cable. | |||
| OBJECT-TYPE | |||
| Counter | |||
| x21IfRxGiantFrames | 1.3.6.1.4.1.272.4.10.1.1.16 | ||
| Count of received frames with illegal framesize. This can occur if a frame delimiter is destroyed. | |||
| OBJECT-TYPE | |||
| Counter | |||
| x21IfTxResets | 1.3.6.1.4.1.272.4.10.1.1.17 | ||
| Count of transmitter resets. Under rare circumstances it might be necessary to reset the transmitter to work properly. | |||
| OBJECT-TYPE | |||
| Counter | |||
| x21IfTxAborts | 1.3.6.1.4.1.272.4.10.1.1.18 | ||
| Count of transmitter aborts. While sending a frame it might be necessary to indicate this frame as aborted. In this case the receiver regards this frame as illegal. | |||
| OBJECT-TYPE | |||
| Counter | |||
| x21IfTxUnderruns | 1.3.6.1.4.1.272.4.10.1.1.19 | ||
| Count of transmitter underruns. The serial data for the X21 card is supplied too slowly. | |||
| OBJECT-TYPE | |||
| Counter | |||
| x21IfTxGiantFrames | 1.3.6.1.4.1.272.4.10.1.1.20 | ||
| Count of transmitted frames with illegal framesize. This can occur if an upper module creates packets with more than the maximum allowed packet size. | |||
| OBJECT-TYPE | |||
| Counter | |||
| Date | |||
| INTEGER | |||
| HexValue | |||
| INTEGER | |||
| X21IfEntry | |||
| SEQUENCE | |||
| INTEGER as x21IfIndex | |||
| INTEGER as x21IfL1State | |||
| INTEGER as x21IfL1Mode | |||
| INTEGER as x21IfIfLeads | |||
| INTEGER as x21IfSpeed | |||
| INTEGER as x21IfL2Mode | |||
| Counter as x21IfSpeedReal | |||
| Counter as x21IfRxPackets | |||
| Counter as x21IfRxOctets | |||
| Counter as x21IfTxPackets | |||
| Counter as x21IfTxOctets | |||
| Counter as x21IfRxResets | |||
| Counter as x21IfRxAborts | |||
| Counter as x21IfRxOverruns | |||
| Counter as x21IfRxCRCErrors | |||
| Counter as x21IfRxGiantFrames | |||
| Counter as x21IfTxResets | |||
| Counter as x21IfTxAborts | |||
| Counter as x21IfTxUnderruns | |||
| Counter as x21IfTxGiantFrames | |||