BROTHER-MIB

File: BROTHER-MIB.mib (290460 bytes)

Imported modules

RFC1155-SMI RFC1213-MIB SNMPv2-TC
RFC-1212 IPV6-TC

Imported symbols

enterprises IpAddress Counter
DisplayString DateAndTime OBJECT-TYPE
Ipv6Address

Defined Objects

brother 1.3.6.1.4.1.2435
OBJECT IDENTIFIER    

nm 1.3.6.1.4.1.2435.2
OBJECT IDENTIFIER    

system 1.3.6.1.4.1.2435.2.3
OBJECT IDENTIFIER    

net-peripheral 1.3.6.1.4.1.2435.2.3.9
OBJECT IDENTIFIER    

net-printer 1.3.6.1.4.1.2435.2.3.9.1
OBJECT IDENTIFIER    

generalDeviceStatus 1.3.6.1.4.1.2435.2.3.9.1.1
OBJECT IDENTIFIER    

status 1.3.6.1.4.1.2435.2.3.9.1.1.2
OBJECT IDENTIFIER    

brJamPlace 1.3.6.1.4.1.2435.2.3.9.1.1.2.9
Location of JAM. 0:No Jam 1:Jam Trays 2:Jam Inside 3:Jam Rear 4:Jam Duplex unit
OBJECT-TYPE    
  INTEGER 0..4  

tonerlow 1.3.6.1.4.1.2435.2.3.9.1.1.2.10
OBJECT IDENTIFIER    

brToner1Low 1.3.6.1.4.1.2435.2.3.9.1.1.2.10.1
Black Toner status. 0:Toner Full 1:Toner Low 2:No Toner Cartridge 3:Toner Empty
OBJECT-TYPE    
  INTEGER 0..3  

brToner2Low 1.3.6.1.4.1.2435.2.3.9.1.1.2.10.2
Cyan Toner status. 0:Toner Ready 1:Toner Low 2:No Toner Cartridge 3:Toner Empty
OBJECT-TYPE    
  INTEGER 0..3  

brToner3Low 1.3.6.1.4.1.2435.2.3.9.1.1.2.10.3
Magenta Toner status. 0:Toner Ready 1:Toner Low 2:No Toner Cartridge 3:Toner Empty
OBJECT-TYPE    
  INTEGER 0..3  

brToner4Low 1.3.6.1.4.1.2435.2.3.9.1.1.2.10.4
Yellow Toner status. 0:Toner Ready 1:Toner Low 2:No Toner Cartridge 3:Toner Empty
OBJECT-TYPE    
  INTEGER 0..3  

brieee1284id 1.3.6.1.4.1.2435.2.3.9.1.1.7
IEEE1284 device ID
OBJECT-TYPE    
  OCTET STRING  

brttt1 1.3.6.1.4.1.2435.2.3.9.1.1.10
unused
OBJECT-TYPE    
  INTEGER 0..255  

net-MFP 1.3.6.1.4.1.2435.2.3.9.2
OBJECT IDENTIFIER    

fax-setup 1.3.6.1.4.1.2435.2.3.9.2.1
OBJECT IDENTIFIER    

autodial 1.3.6.1.4.1.2435.2.3.9.2.1.1
OBJECT IDENTIFIER    

onetouchDial 1.3.6.1.4.1.2435.2.3.9.2.1.1.1
OBJECT IDENTIFIER    

brOneTouchDialCount 1.3.6.1.4.1.2435.2.3.9.2.1.1.1.1
Maximum number of One touch dial.
OBJECT-TYPE    
  INTEGER 1..65535  

brOneTouchDialTable 1.3.6.1.4.1.2435.2.3.9.2.1.1.1.2
This table represents One touch dial.
OBJECT-TYPE    
  SEQUENCE OF  
    BrOneTouchDialEntry

brOneTouchDialEntry 1.3.6.1.4.1.2435.2.3.9.2.1.1.1.2.1
A row in the OneTouchDial table. Rows cannot be created or deleted.
OBJECT-TYPE    
  BrOneTouchDialEntry  

brOneTouchDialIndex 1.3.6.1.4.1.2435.2.3.9.2.1.1.1.2.1.1
The One touch dial number.
OBJECT-TYPE    
  INTEGER 1..65535  

brOneTouchDialData 1.3.6.1.4.1.2435.2.3.9.2.1.1.1.2.1.2
The One Touch dial data.
OBJECT-TYPE    
  OCTET STRING  

speedDial 1.3.6.1.4.1.2435.2.3.9.2.1.1.2
OBJECT IDENTIFIER    

brSpeedDialCount 1.3.6.1.4.1.2435.2.3.9.2.1.1.2.1
Maximum number of Speed dial.
OBJECT-TYPE    
  INTEGER 1..65535  

brSpeedDialTable 1.3.6.1.4.1.2435.2.3.9.2.1.1.2.2
This table represents Speed dial.
OBJECT-TYPE    
  SEQUENCE OF  
    BrSpeedDialEntry

brSpeedDialEntry 1.3.6.1.4.1.2435.2.3.9.2.1.1.2.2.1
A row in the speedDial table. Rows cannot be created or deleted.
OBJECT-TYPE    
  BrSpeedDialEntry  

brSpeedDialIndex 1.3.6.1.4.1.2435.2.3.9.2.1.1.2.2.1.1
The Speed dial number.
OBJECT-TYPE    
  INTEGER 1..65535  

brSpeedDialData 1.3.6.1.4.1.2435.2.3.9.2.1.1.2.2.1.2
The Speed dial Data.
OBJECT-TYPE    
  OCTET STRING  

brDialDataAllClear 1.3.6.1.4.1.2435.2.3.9.2.1.1.3
Clear the all data of Onetouch dial and Speed dial.
OBJECT-TYPE    
  INTEGER 1..65535  

fax-general 1.3.6.1.4.1.2435.2.3.9.2.1.2
OBJECT IDENTIFIER    

brFaxReceiveMode 1.3.6.1.4.1.2435.2.3.9.2.1.2.1
Fax Receive Mode 0:Auto 1:Manual 2:FaxTel 3:TAD
OBJECT-TYPE    
  INTEGER  

brRingDelayCount 1.3.6.1.4.1.2435.2.3.9.2.1.2.2
Ring Delay Count
OBJECT-TYPE    
  INTEGER 0..4  

brOwnFaxNumber 1.3.6.1.4.1.2435.2.3.9.2.1.2.3
Own Fax Number
OBJECT-TYPE    
  OCTET STRING  

scanner-setup 1.3.6.1.4.1.2435.2.3.9.2.11
OBJECT IDENTIFIER    

scanToInfo 1.3.6.1.4.1.2435.2.3.9.2.11.1
OBJECT IDENTIFIER    

brRegisterKeyInfo 1.3.6.1.4.1.2435.2.3.9.2.11.1.1
Add the ScanTo information. If device receives GET request, device should reply fix value TRUE(writable), FALSE(not writable) to the client.
OBJECT-TYPE    
  OCTET STRING  

brUnRegisterKeyInfo 1.3.6.1.4.1.2435.2.3.9.2.11.1.2
Remove the ScanTo information. If device receives GET request, device should reply fix value TRUE (writable), FALSE (not writable) to the client.
OBJECT-TYPE    
  OCTET STRING  

brNetSKeyReceiverAddress 1.3.6.1.4.1.2435.2.3.9.2.11.1.5
IP Address or the name of the S-Key Receiver.
OBJECT-TYPE    
  OCTET STRING SIZE(0..63)  

mfpCapability 1.3.6.1.4.1.2435.2.3.9.2.101
OBJECT IDENTIFIER    

mcGeneral 1.3.6.1.4.1.2435.2.3.9.2.101.1
OBJECT IDENTIFIER    

mcgRemoteSetup 1.3.6.1.4.1.2435.2.3.9.2.101.1.11
OBJECT IDENTIFIER    

brNetRemoteSetUpSupported 1.3.6.1.4.1.2435.2.3.9.2.101.1.11.1
0 indicates the Net Remote Setup function is not supported. 1 indicates the Net Remote Setup function is implemented by the firmware
OBJECT-TYPE    
  INTEGER 0..1  

brNetRemoteSetUpEnable 1.3.6.1.4.1.2435.2.3.9.2.101.1.11.2
0 indicates the Net Remote Setup is not enabled. 1 indicates that the Net Remote Setup is enabled. Writing a non-zero value will enable the Net Remote Setup if it is supported by the firmware.
OBJECT-TYPE    
  INTEGER 0..1  

brNetRemoteSetUpFileFormat 1.3.6.1.4.1.2435.2.3.9.2.101.1.11.3
It is a file format of the Net Remote Setup function.
OBJECT-TYPE    
  INTEGER rms(1), rmd(2), rmsrmd(3)  

mcFax 1.3.6.1.4.1.2435.2.3.9.2.101.2
OBJECT IDENTIFIER    

mcfGeneral 1.3.6.1.4.1.2435.2.3.9.2.101.2.1
OBJECT IDENTIFIER    

brFaxSupported 1.3.6.1.4.1.2435.2.3.9.2.101.2.1.1
0 indicates the Fax function is not supported. 1 indicates the Fax function is implemented by the firmware
OBJECT-TYPE    
  INTEGER 0..1  

brIFaxSupported 1.3.6.1.4.1.2435.2.3.9.2.101.2.1.3
0 indicates the IFax function is not supported. 1 indicates the IFax function is implemented by the firmware
OBJECT-TYPE    
  INTEGER 0..1  

mcfNetFaxShare 1.3.6.1.4.1.2435.2.3.9.2.101.2.11
OBJECT IDENTIFIER    

brNetFaxShareSupported 1.3.6.1.4.1.2435.2.3.9.2.101.2.11.1
0 indicates the Net Fax Share is not supported. 1 indicates the Net Fax Share is implemented by the firmware
OBJECT-TYPE    
  INTEGER 0..1  

brNetFaxShareEnable 1.3.6.1.4.1.2435.2.3.9.2.101.2.11.2
0 indicates the Net Fax Share is not enabled. 1 indicates that the Net Fax Share is enabled. Writing a non-zero value will enable the Net Fax Share if it is supported by the firmware.
OBJECT-TYPE    
  INTEGER 0..1  

mcfNetPcFaxRx 1.3.6.1.4.1.2435.2.3.9.2.101.2.12
OBJECT IDENTIFIER    

brNetPcFaxRxSupported 1.3.6.1.4.1.2435.2.3.9.2.101.2.12.1
0 indicates the Net PC Fax Rx is not supported. 1 indicates the Net PC Fax Rx is implemented by the firmware
OBJECT-TYPE    
  INTEGER 0..1  

brNetPcFaxRxEnable 1.3.6.1.4.1.2435.2.3.9.2.101.2.12.2
0 indicates the Net PC Fax Rx is not enabled. 1 indicates that the Net PC Fax Rx is enabled. Writing a non-zero value will enable the Net PC Fax Rx if it is supported by the firmware.
OBJECT-TYPE    
  INTEGER 0..1  

brNetRegisterPcFaxInfo 1.3.6.1.4.1.2435.2.3.9.2.101.2.12.3
Add the PcFax information. If device receives GET request, device should reply fix value TRUE(writable), FALSE(not writable) to the client.
OBJECT-TYPE    
  OCTET STRING  

mcfFaxInfomation 1.3.6.1.4.1.2435.2.3.9.2.101.2.101
OBJECT IDENTIFIER    

brPhoneNumberLastFax 1.3.6.1.4.1.2435.2.3.9.2.101.2.101.1
Phone Number of Last Fax
OBJECT-TYPE    
  OCTET STRING SIZE(0..20)  

brPagesSentLastFax 1.3.6.1.4.1.2435.2.3.9.2.101.2.101.2
Pages Sent in Last Fax
OBJECT-TYPE    
  Counter  

brTimestampLastFax 1.3.6.1.4.1.2435.2.3.9.2.101.2.101.3
Timestamp of Last Fax
OBJECT-TYPE    
  DateAndTime  

brFaxHeaderInfo 1.3.6.1.4.1.2435.2.3.9.2.101.2.101.4
Fax Header Infomation
OBJECT-TYPE    
  DisplayString SIZE(0..50)  

mcScanner 1.3.6.1.4.1.2435.2.3.9.2.101.3
OBJECT IDENTIFIER    

mcsNetScanner 1.3.6.1.4.1.2435.2.3.9.2.101.3.11
OBJECT IDENTIFIER    

brNetScannerSupported 1.3.6.1.4.1.2435.2.3.9.2.101.3.11.1
0 indicates the Net Scanner is not supported. 1 indicates the Net Scanner is implemented by the firmware
OBJECT-TYPE    
  INTEGER 0..1  

brNetScannerEnable 1.3.6.1.4.1.2435.2.3.9.2.101.3.11.2
0 indicates the Net Scanner is not enabled. 1 indicates that the Net Scanner is enabled. Writing a non-zero value will enable the Net Scanner if it is supported by the firmware.
OBJECT-TYPE    
  INTEGER 0..1  

mcsNetSKy 1.3.6.1.4.1.2435.2.3.9.2.101.3.12
OBJECT IDENTIFIER    

brNetSKeySupported 1.3.6.1.4.1.2435.2.3.9.2.101.3.12.1
0 indicates the Net S-Key is not supported. 1 indicates the Net S-Key is implemented by the firmware
OBJECT-TYPE    
  INTEGER 0..1  

brNetSKeyEnable 1.3.6.1.4.1.2435.2.3.9.2.101.3.12.2
0 indicates the Net S-Key is not enabled. 1 indicates that the Net S-Key is enabled. Writing a non-zero value will enable the Net S-Key if it is supported by the firmware.
OBJECT-TYPE    
  INTEGER 0..1  

mfpgeneral-setup 1.3.6.1.4.1.2435.2.3.9.2.111
OBJECT IDENTIFIER    

brServiceMode 1.3.6.1.4.1.2435.2.3.9.2.111.1
Service Mode
OBJECT-TYPE    
  OCTET STRING  

brLockMode 1.3.6.1.4.1.2435.2.3.9.2.111.2
Lock Mode 0:normal 1:Customer 2:Lock
OBJECT-TYPE    
  INTEGER 0..2  

brActivityReportSetting 1.3.6.1.4.1.2435.2.3.9.2.111.3
Activity Report Setting 0:off 1:every 1hour 3:every 3hour 6:every 6hour 12:every 12hour 24:every 24hour 48:every 2day 96:every 4day 240:every Sunday 241:every Monday 242:every Tueseday 243:every Wednesday 244:every Thurseday 245:every Friday 246:every Saturday 255:interval 50FAX
OBJECT-TYPE    
  INTEGER  

netPML 1.3.6.1.4.1.2435.2.3.9.4
OBJECT IDENTIFIER    

netPMLmgmt 1.3.6.1.4.1.2435.2.3.9.4.2
OBJECT IDENTIFIER    

device 1.3.6.1.4.1.2435.2.3.9.4.2.1
OBJECT IDENTIFIER    

destination-subsystem1 1.3.6.1.4.1.2435.2.3.9.4.2.1.1
OBJECT IDENTIFIER    

sleep 1.3.6.1.4.1.2435.2.3.9.4.2.1.1.1
OBJECT IDENTIFIER    

brpowerstime 1.3.6.1.4.1.2435.2.3.9.4.2.1.1.1.1
PowerSave Timeout value. 1 to 2147483647 (sec)
OBJECT-TYPE    
  INTEGER 1..2147483647  

autoc 1.3.6.1.4.1.2435.2.3.9.4.2.1.1.2
OBJECT IDENTIFIER    

brautocont 1.3.6.1.4.1.2435.2.3.9.4.2.1.1.2.7
Auto Continue. 1:Off 2:On
OBJECT-TYPE    
  INTEGER 0..2  

simm 1.3.6.1.4.1.2435.2.3.9.4.2.1.1.4
OBJECT IDENTIFIER    

specification 1.3.6.1.4.1.2435.2.3.9.4.2.1.1.4.1
OBJECT IDENTIFIER    

simmkind0 1.3.6.1.4.1.2435.2.3.9.4.2.1.1.4.1.1
OBJECT IDENTIFIER    

brsimmtype0 1.3.6.1.4.1.2435.2.3.9.4.2.1.1.4.1.1.4
SIMM type on slot0. 0: unconfirmed : 0 MB 1: empty 2: unconfirmed 3: No Supported : 0 MB 4: Read Only Memory 5: Volatility RAM : size MB 6: Un Volatility RAM : size MB 7: Flash Memory : size MB 8: Disk Drive : 0 MB 9: RAM/ROM : 0MB 10: Loading Paper Device 11: Out Paper Device 12: unconfirmed : 0 MB ato ha onaji
OBJECT-TYPE    
  INTEGER  

brsimmsize0 1.3.6.1.4.1.2435.2.3.9.4.2.1.1.4.1.1.5
SIMM size on slot0
OBJECT-TYPE    
  INTEGER  

simmkind1 1.3.6.1.4.1.2435.2.3.9.4.2.1.1.4.1.2
OBJECT IDENTIFIER    

brsimmtype1 1.3.6.1.4.1.2435.2.3.9.4.2.1.1.4.1.2.4
SIMM type on slot1. 0: unconfirmed : 0 MB 1: empty 2: unconfirmed 3: No Supported : 0 MB 4: Read Only Memory 5: Volatility RAM : size MB 6: Un Volatility RAM : size MB 7: Flash Memory : size MB 8: Disk Drive : 0 MB 9: RAM/ROM : 0MB 10: Loading Paper Device 11: Out Paper Device 12: unconfirmed : 0 MB ato ha onaji
OBJECT-TYPE    
  INTEGER  

brsimmsize1 1.3.6.1.4.1.2435.2.3.9.4.2.1.1.4.1.2.5
SIMM size on slot1
OBJECT-TYPE    
  INTEGER  

simmkind2 1.3.6.1.4.1.2435.2.3.9.4.2.1.1.4.1.3
OBJECT IDENTIFIER    

brsimmtype2 1.3.6.1.4.1.2435.2.3.9.4.2.1.1.4.1.3.4
SIMM type on slot2. 0: unconfirmed : 0 MB 1: empty 2: unconfirmed 3: No Supported : 0 MB 4: Read Only Memory 5: Volatility RAM : size MB 6: Un Volatility RAM : size MB 7: Flash Memory : size MB 8: Disk Drive : 0 MB 9: RAM/ROM : 0MB 10: Loading Paper Device 11: Out Paper Device 12: unconfirmed : 0 MB ato ha onaji
OBJECT-TYPE    
  INTEGER  

brsimmsize2 1.3.6.1.4.1.2435.2.3.9.4.2.1.1.4.1.3.5
SIMM size on slot2.
OBJECT-TYPE    
  INTEGER  

simmkind3 1.3.6.1.4.1.2435.2.3.9.4.2.1.1.4.1.4
OBJECT IDENTIFIER    

brsimmtype3 1.3.6.1.4.1.2435.2.3.9.4.2.1.1.4.1.4.4
SIMM type on slot3. 0: unconfirmed : 0 MB 1: empty 2: unconfirmed 3: No Supported : 0 MB 4: Read Only Memory 5: Volatility RAM : size MB 6: Un Volatility RAM : size MB 7: Flash Memory : size MB 8: Disk Drive : 0 MB 9: RAM/ROM : 0MB 10: Loading Paper Device 11: Out Paper Device 12: unconfirmed : 0 MB ato ha onaji
OBJECT-TYPE    
  INTEGER  

brsimmsize3 1.3.6.1.4.1.2435.2.3.9.4.2.1.1.4.1.4.5
SIMM type on slot3.
OBJECT-TYPE    
  INTEGER  

bio1-explanation 1.3.6.1.4.1.2435.2.3.9.4.2.1.1.4.3
OBJECT IDENTIFIER    

determined 1.3.6.1.4.1.2435.2.3.9.4.2.1.1.4.3.1
OBJECT IDENTIFIER    

brTBD1 1.3.6.1.4.1.2435.2.3.9.4.2.1.1.4.3.1.4
unused
OBJECT-TYPE    
  INTEGER 1..15  

destination-subsystem2 1.3.6.1.4.1.2435.2.3.9.4.2.1.2
OBJECT IDENTIFIER    

printerjob 1.3.6.1.4.1.2435.2.3.9.4.2.1.2.1
OBJECT IDENTIFIER    

jobend 1.3.6.1.4.1.2435.2.3.9.4.2.1.2.1.1
OBJECT IDENTIFIER    

brtimeout 1.3.6.1.4.1.2435.2.3.9.4.2.1.2.1.1.1
Job Timeout. 1 to 2147483647(sec)
OBJECT-TYPE    
  INTEGER 1..2147483647  

brTBD2 1.3.6.1.4.1.2435.2.3.9.4.2.1.2.1.1.5
unused
OBJECT-TYPE    
  INTEGER 1..15  

destination-subsystem3 1.3.6.1.4.1.2435.2.3.9.4.2.1.3
OBJECT IDENTIFIER    

prt-setup 1.3.6.1.4.1.2435.2.3.9.4.2.1.3.3
OBJECT IDENTIFIER    

prt-condition 1.3.6.1.4.1.2435.2.3.9.4.2.1.3.3.1
OBJECT IDENTIFIER    

brpersonality 1.3.6.1.4.1.2435.2.3.9.4.2.1.3.3.1.1
Printer Emulation setting. 1:PCL 2:HPGL 4:PS 5:AUTO 6:IBM 7:EPSON 8:HBP
OBJECT-TYPE    
  INTEGER pcl(1), hpgl(2), ps(4), auto(5), ibm(6), epson(7), hbp(8)  

brorientation 1.3.6.1.4.1.2435.2.3.9.4.2.1.3.3.1.2
Default Paper Orientation. 1:portrait 2:landscape
OBJECT-TYPE    
  INTEGER 0..4  

brcopies 1.3.6.1.4.1.2435.2.3.9.4.2.1.3.3.1.4
Default Copy Pages. 1-999 pages
OBJECT-TYPE    
  INTEGER 1..999  

brTBD3 1.3.6.1.4.1.2435.2.3.9.4.2.1.3.3.1.6
unused
OBJECT-TYPE    
  INTEGER 1..15  

brresolution 1.3.6.1.4.1.2435.2.3.9.4.2.1.3.3.1.8
Default Resolution. 300, 600 or 1200dpi
OBJECT-TYPE    
  INTEGER 0..1200  

brpageprotect 1.3.6.1.4.1.2435.2.3.9.4.2.1.3.3.1.10
Page Protect mode 1:Off 3:Auto 4:Letter 5:Legal 6:A4
OBJECT-TYPE    
  INTEGER 0..6  

brlines 1.3.6.1.4.1.2435.2.3.9.4.2.1.3.3.1.11
lines per page. 5-128
OBJECT-TYPE    
  INTEGER 5..128  

brpaper 1.3.6.1.4.1.2435.2.3.9.4.2.1.3.3.1.13
Default Paper size. -1:No Casette 1:Executive 2:Letter 3:Legal 24:A6 25:A5 26:A4 27:A3(ISO) 45:B5(JIS) 46:B4(JIS) 80:Monarch 81:COM10 90:DL 91:C5 99:B6 100:B5 890:LEDGER 891:A3PLUS(13x19) 892:Letter Short Edge 893:A4 Short Edge 894:A4LONG 895:Executive Short Edge 896:B5(ISO) Short Edge 897:CUSTOM (ANY) 898:A4/Letter 899:B5/Executive 900:Envelopes 901:DL-L 902:HAGAKI 903:FOLIO 904:ORGANIZER J 905:ORGANIZER K 906:ORGANIZER L 907:ORGANIZER M 908:USER DEFINED 911:Detect Sensor 920:3x5(inches) 921:Envelopes Y4 922:Largest envelopes of the West 923:A5L 924:B6JIS 925:16K195x270 926:16K184x260 927:197x273 999:Other 1000:No Casette 1001:Auto
OBJECT-TYPE    
  INTEGER executive(1), letter(2), legal(3), a6(24), a5(25), a4(26), a3ISO(27), b5JIS(45), b4JIS(46), monarch(80), com10(81), dl(90), c5(91), b6(99), b5(100), ledger(890), a3PLUS(891), letterShortEdge(892), a4ShortEdge(893), a4LONG(894), executiveShortEdge(895), b5ISOShortEdge(896), custom(897), a4Letter(898), b5Executive(899), envelopes(900), dll(901), hagaki(902), folio(903), organaizerJ(904), organaizerK(905), organaizerL(906), organaizerM(907), userdefined(908), detectsensor(911), inches3x5(920), envelopesY4(921), largestEnvelopesTheWest(922), prc16k195x270(925), a5l(923), b6JIS(924), prc16k184x260(926), prc16k197x273(927), auto(1001)  

brpapertype 1.3.6.1.4.1.2435.2.3.9.4.2.1.3.3.1.22
Default Media type. 0:Regular 1:Thick paper 2:Thicker paper 3:Transparency 4:Thin paper 5:Bond paper 6:ENVELOPES 7:ENV. THICK 8:ENV. THIN 9:RECYCLED 10:HAGAKI 11:LABEL 1nd (default) Tray PaperType
OBJECT-TYPE    
  INTEGER  

brpapertype2 1.3.6.1.4.1.2435.2.3.9.4.2.1.3.3.1.23
Default Media type. 0:Regular 1:Thick paper 2:Thicker paper 3:Transparency 4:Thin paper 5:Bond paper 6:ENVELOPES 7:ENV. THICK 8:ENV. THIN 9:RECYCLED 10:HAGAKI 11:LABEL 2nd Tray PaperType
OBJECT-TYPE    
  INTEGER  

brpapertypeMP 1.3.6.1.4.1.2435.2.3.9.4.2.1.3.3.1.26
Default Media type. 0:Regular 1:Thick paper 2:Thicker paper 3:Transparency 4:Thin paper 5:Bond paper 6:ENVELOPES 7:ENV. THICK 8:ENV. THIN 9:RECYCLED 10:HAGAKI 11:LABEL 1nd (default) Tray PaperType
OBJECT-TYPE    
  INTEGER  

destination-subsystem4 1.3.6.1.4.1.2435.2.3.9.4.2.1.4
OBJECT IDENTIFIER    


prt-density 1.3.6.1.4.1.2435.2.3.9.4.2.1.4.1.1
OBJECT IDENTIFIER    

brdensity 1.3.6.1.4.1.2435.2.3.9.4.2.1.4.1.1.5
Print Density. -15..15
OBJECT-TYPE    
  INTEGER -15..15  

status-prt-eng 1.3.6.1.4.1.2435.2.3.9.4.2.1.4.1.2
OBJECT IDENTIFIER    

tray 1.3.6.1.4.1.2435.2.3.9.4.2.1.4.1.3
OBJECT IDENTIFIER    

manual 1.3.6.1.4.1.2435.2.3.9.4.2.1.4.1.3.1
OBJECT IDENTIFIER    

brmanualfeed 1.3.6.1.4.1.2435.2.3.9.4.2.1.4.1.3.1.4
Manualfeed mode. 1:Off 2:On
OBJECT-TYPE    
  INTEGER 0..2  

traysize 1.3.6.1.4.1.2435.2.3.9.4.2.1.4.1.3.3
OBJECT IDENTIFIER    

mp 1.3.6.1.4.1.2435.2.3.9.4.2.1.4.1.3.3.1
OBJECT IDENTIFIER    

brmpsize 1.3.6.1.4.1.2435.2.3.9.4.2.1.4.1.3.3.1.1
MP Tray paper size -1:No Casette 1:Executive 2:Letter 3:Legal 24:A6 25:A5 26:A4 27:A3(ISO) 45:B5(JIS) 46:B4(JIS) 80:Monarch 81:COM10 90:DL 91:C5 99:B6 100:B5 890:LEDGER 891:A3PLUS(13x19) 892:Letter Short Edge 893:A4 Short Edge 894:A4LONG 895:Executive Short Edge 896:B5(ISO) Short Edge 897:CUSTOM 898:A4/Letter 899:B5/Executive 900:Envelopes 901:DL-L 902:HAGAKI 903:FOLIO 904:ORGANIZER J 905:ORGANIZER K 906:ORGANIZER L 907:ORGANIZER M 908:USER DEFINED 911:Detect Sensor
OBJECT-TYPE    
  INTEGER executive(1), letter(2), legal(3), a6(24), a5(25), a4(26), a3ISO(27), b5JIS(45), b4JIS(46), monarch(80), com10(81), dl(90), c5(91), b6(99), b5(100), ledger(890), a3PLUS(891), letterShortEdge(892), a4ShortEdge(893), a4LONG(894), executiveShortEdge(895), b5ISOShortEdge(896), custom(897), a4Letter(898), b5Executive(899), envelopes(900), dll(901), hagaki(902), folio(903), organaizerJ(904), organaizerK(905), organaizerL(906), organaizerM(907), userdefined(908), detectsensor(911), inches3x5(920), envelopesY4(921), largestEnvelopesTheWest(922)  

cassette 1.3.6.1.4.1.2435.2.3.9.4.2.1.4.1.3.3.2
OBJECT IDENTIFIER    

brtray1size 1.3.6.1.4.1.2435.2.3.9.4.2.1.4.1.3.3.2.1
Tray1 paper size -1:No Casette 1:Executive 2:Letter 3:Legal 24:A6 25:A5 26:A4 27:A3(ISO) 45:B5(JIS) 46:B4(JIS) 80:Monarch 81:COM10 90:DL 91:C5 99:B6 100:B5 890:LEDGER 891:A3PLUS(13x19) 892:Letter Short Edge 893:A4 Short Edge 894:A4LONG 895:Executive Short Edge 896:B5(ISO) Short Edge 897:CUSTOM 898:A4/Letter 899:B5/Executive 900:Envelopes 901:DL-L 902:HAGAKI 903:FOLIO 904:ORGANIZER J 905:ORGANIZER K 906:ORGANIZER L 907:ORGANIZER M 908:USER DEFINED 911:Detect Sensor
OBJECT-TYPE    
  INTEGER executive(1), letter(2), legal(3), a6(24), a5(25), a4(26), a3ISO(27), b5JIS(45), b4JIS(46), monarch(80), com10(81), dl(90), c5(91), b6(99), b5(100), ledger(890), a3PLUS(891), letterShortEdge(892), a4ShortEdge(893), a4LONG(894), executiveShortEdge(895), b5ISOShortEdge(896), custom(897), a4Letter(898), b5Executive(899), envelopes(900), dll(901), hagaki(902), folio(903), organaizerJ(904), organaizerK(905), organaizerL(906), organaizerM(907), userdefined(908), detectsensor(911), inches3x5(920), envelopesY4(921), largestEnvelopesTheWest(922)  

cassette2 1.3.6.1.4.1.2435.2.3.9.4.2.1.4.1.3.3.3
OBJECT IDENTIFIER    

brtray2size 1.3.6.1.4.1.2435.2.3.9.4.2.1.4.1.3.3.3.1
Tray2 paper size -1:No Casette 1:Executive 2:Letter 3:Legal 24:A6 25:A5 26:A4 27:A3(ISO) 45:B5(JIS) 46:B4(JIS) 80:Monarch 81:COM10 90:DL 91:C5 99:B6 100:B5 890:LEDGER 891:A3PLUS(13x19) 892:Letter Short Edge 893:A4 Short Edge 894:A4LONG 895:Executive Short Edge 896:B5(ISO) Short Edge 897:CUSTOM 898:A4/Letter 899:B5/Executive 900:Envelopes 901:DL-L 902:HAGAKI 903:FOLIO 904:ORGANIZER J 905:ORGANIZER K 906:ORGANIZER L 907:ORGANIZER M 908:USER DEFINED 911:Detect Sensor
OBJECT-TYPE    
  INTEGER executive(1), letter(2), legal(3), a6(24), a5(25), a4(26), a3ISO(27), b5JIS(45), b4JIS(46), monarch(80), com10(81), dl(90), c5(91), b6(99), b5(100), ledger(890), a3PLUS(891), letterShortEdge(892), a4ShortEdge(893), a4LONG(894), executiveShortEdge(895), b5ISOShortEdge(896), custom(897), a4Letter(898), b5Executive(899), envelopes(900), dll(901), hagaki(902), folio(903), organaizerJ(904), organaizerK(905), organaizerL(906), organaizerM(907), userdefined(908), detectsensor(911), inches3x5(920), envelopesY4(921), largestEnvelopesTheWest(922)  

cassette3 1.3.6.1.4.1.2435.2.3.9.4.2.1.4.1.3.3.4
OBJECT IDENTIFIER    

brtray3size 1.3.6.1.4.1.2435.2.3.9.4.2.1.4.1.3.3.4.1
Tray3 paper size -1:No Casette 1:Executive 2:Letter 3:Legal 24:A6 25:A5 26:A4 27:A3(ISO) 45:B5(JIS) 46:B4(JIS) 80:Monarch 81:COM10 90:DL 91:C5 99:B6 100:B5 890:LEDGER 891:A3PLUS(13x19) 892:Letter Short Edge 893:A4 Short Edge 894:A4LONG 895:Executive Short Edge 896:B5(ISO) Short Edge 897:CUSTOM 898:A4/Letter 899:B5/Executive 900:Envelopes 901:DL-L 902:HAGAKI 903:FOLIO 904:ORGANIZER J 905:ORGANIZER K 906:ORGANIZER L 907:ORGANIZER M 908:USER DEFINED 911:Detect Sensor
OBJECT-TYPE    
  INTEGER executive(1), letter(2), legal(3), a6(24), a5(25), a4(26), a3ISO(27), b5JIS(45), b4JIS(46), monarch(80), com10(81), dl(90), c5(91), b6(99), b5(100), ledger(890), a3PLUS(891), letterShortEdge(892), a4ShortEdge(893), a4LONG(894), executiveShortEdge(895), b5ISOShortEdge(896), custom(897), a4Letter(898), b5Executive(899), envelopes(900), dll(901), hagaki(902), folio(903), organaizerJ(904), organaizerK(905), organaizerL(906), organaizerM(907), userdefined(908), detectsensor(911), inches3x5(920), envelopesY4(921), largestEnvelopesTheWest(922)  

cassette4 1.3.6.1.4.1.2435.2.3.9.4.2.1.4.1.3.3.5
OBJECT IDENTIFIER    

brtray4size 1.3.6.1.4.1.2435.2.3.9.4.2.1.4.1.3.3.5.1
Tray4 paper size -1:No Casette 1:Executive 2:Letter 3:Legal 24:A6 25:A5 26:A4 27:A3(ISO) 45:B5(JIS) 46:B4(JIS) 80:Monarch 81:COM10 90:DL 91:C5 99:B6 100:B5 890:LEDGER 891:A3PLUS(13x19) 892:Letter Short Edge 893:A4 Short Edge 894:A4LONG 895:Executive Short Edge 896:B5(ISO) Short Edge 897:CUSTOM 898:A4/Letter 899:B5/Executive 900:Envelopes 901:DL-L 902:HAGAKI 903:FOLIO 904:ORGANIZER J 905:ORGANIZER K 906:ORGANIZER L 907:ORGANIZER M 908:USER DEFINED 911:Detect Sensor
OBJECT-TYPE    
  INTEGER executive(1), letter(2), legal(3), a6(24), a5(25), a4(26), a3ISO(27), b5JIS(45), b4JIS(46), monarch(80), com10(81), dl(90), c5(91), b6(99), b5(100), ledger(890), a3PLUS(891), letterShortEdge(892), a4ShortEdge(893), a4LONG(894), executiveShortEdge(895), b5ISOShortEdge(896), custom(897), a4Letter(898), b5Executive(899), envelopes(900), dll(901), hagaki(902), folio(903), organaizerJ(904), organaizerK(905), organaizerL(906), organaizerM(907), userdefined(908), detectsensor(911), inches3x5(920), envelopesY4(921), largestEnvelopesTheWest(922)  

economy 1.3.6.1.4.1.2435.2.3.9.4.2.1.4.1.6
OBJECT IDENTIFIER    

brret 1.3.6.1.4.1.2435.2.3.9.4.2.1.4.1.6.5
HRC mode. 1:Off 2:Bright 3:Medium 4:Dark
OBJECT-TYPE    
  INTEGER 0..4  

breconomode 1.3.6.1.4.1.2435.2.3.9.4.2.1.4.1.6.7
Toner Save mode. 100:Off 0:On
OBJECT-TYPE    
  INTEGER 0..100  

brorg 1.3.6.1.4.1.2435.2.3.9.4.2.1.5
OBJECT IDENTIFIER    

printersetup 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1
OBJECT IDENTIFIER    

general 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.1
OBJECT IDENTIFIER    

brPrtGeneralEmulationTimeout 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.1.1
Emulation Timeout. 1- 99(sec)
OBJECT-TYPE    
  INTEGER 1..99  

brPrtGeneralFeeder 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.1.2
Default Feeder mode. 0:Auto 1:MP Tray 2:Tray1 3:Tray2 4:Tray3 5:Tray4
OBJECT-TYPE    
  INTEGER 0..5  

brPrtGeneralPowerSave 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.1.3
Power Save mode. 1:Off 2:On
OBJECT-TYPE    
  INTEGER 0..2  

brPrtGeneralBuzzer 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.1.4
Buzzer. 1:Off 2:On
OBJECT-TYPE    
  INTEGER 0..2  

brPrtGeneralColor 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.1.5
Default Color mode 1:Monochrome 2:Color 3:Auto
OBJECT-TYPE    
  INTEGER 0..3  

brPrtGeneralDuplex 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.1.6
Duplex mode 1:Off(Simplex) 2:On(Duplex)
OBJECT-TYPE    
  INTEGER 0..2  

brPrtGeneralBinding 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.1.7
Binding type 3:Short Edge 2:Long Edge
OBJECT-TYPE    
  INTEGER 0..3  

advanced 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2
OBJECT IDENTIFIER    

brPrtAdvancedPriority 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.1
FX/XL Priority. 1:IBM XL 2:EPSON FX
OBJECT-TYPE    
  INTEGER 0..2  

brPrtAdvancedUseMPTrayFirst 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.2
MP Tray First 1:No 2:Yes
OBJECT-TYPE    
  INTEGER 0..2  

brPrtAdvancedMPTrayFeed 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.3
MP Tray feed mode. 1:Single 2:Continuous
OBJECT-TYPE    
  INTEGER 0..2  

brPrtAdvancedXOffset 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.4
X Offset. -500 to +500 pixel(600dpi)
OBJECT-TYPE    
  INTEGER -500..500  

brPrtAdvancedYOffset 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.5
Y Offset. -500 to +500 pixel(600dpi)
OBJECT-TYPE    
  INTEGER -500..500  

brPrtAdvancedImageCompression 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.6
Image Compression mode. 0:Auto 1:Off 2:On
OBJECT-TYPE    
  INTEGER 0..2  

autoff 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.7
OBJECT IDENTIFIER    

brPrtAdvancedAutoFormFeed 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.7.1
Auto Formfeed mode. 1:Off 2:On
OBJECT-TYPE    
  INTEGER 0..2  

brPrtAdvancedAutoTimeout 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.7.2
Auto Formfeed timeout. 1-99 (sec)
OBJECT-TYPE    
  INTEGER 1..99  

brPrtAdvancedFFSuppress 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.8
FF Suppress mode. 1:Off 2:On
OBJECT-TYPE    
  INTEGER 0..2  

brPrtAdvancedTonerLowPrint 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.9
Print mode on Toner Low. 1:Stop 2:Continue
OBJECT-TYPE    
  INTEGER 0..2  

brPrtAdvancedPrintDensity 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.10
Print Density. 1-15
OBJECT-TYPE    
  INTEGER 0..15  

brPrtAdvancedInputBuffer 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.11
Input Buffer size. 1-15 blocks
OBJECT-TYPE    
  INTEGER 1..15  

brPrtAdvancedLanguage 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.12
1:ENGLISH 2:DANISH 3:DUTCH 4:FINNISH 5:FRENCH 6:GERMAN 7:ITALIAN 8:NORWEGIAN 9:PORTUGUESE 10:SWEDISH 11:SPANISH 12:TURKISH 13:POLISH 14:JAPANESE 15:RUSSIAN 16:CZECH 17:HUNGARIAN 18:ROMANIAN 19:BULGARIAN 20:SLOVAKIAN 21:CHINESE 22:BRAZIL
OBJECT-TYPE    
  INTEGER english(1), danish(2), dutch(3), finish(4), french(5), german(6), italian(7), norwegian(8), portuguse(9), swedish(10), spanish(11), turkish(12), polish(13), japanese(14), russian(15), czech(16), hungarian(17), romanian(18), bulgarian(19), slovakian(20), chinese(21), brazil(22)  

brSecurePrintRAMSizeMax 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.13
The Max of Secure print RAM Size
OBJECT-TYPE    
  INTEGER 0..2147483647  

brSecurePrintRAMSize 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.14
Secure print RAM Size
OBJECT-TYPE    
  INTEGER 0..2147483647  

brPrtAdvancedJamRecovery 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.15
Jam recovery setting
OBJECT-TYPE    
  INTEGER off(1), on(2)  

brPrtAdvancedSleepIndication 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.16
By enabling the Dimmed option, the status LED is dimmed while the printer is in sleep mode.
OBJECT-TYPE    
  INTEGER off(1), dimmed(2)  

brPrtAdvancedDestination 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.17
Destination
OBJECT-TYPE    
  INTEGER standardOutputTray(1), oct(2), octStack(3)  

brPrtAdvancedLowerLCD 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.18
Lower LCD
OBJECT-TYPE    
  INTEGER nonePage(1), counter(2), jobName(3)  

brPrtAdvancedAutoOnline 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.19
Auto Online
OBJECT-TYPE    
  INTEGER off(1), on(2)  

brPrtAdvancedButtonRepeat 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.20
Button Repeat. 0.1-2.0
OBJECT-TYPE    
  INTEGER 1..20  

brPrtAdvancedMessageScroll 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.21
Message Scroll. 1-10
OBJECT-TYPE    
  INTEGER 1..20  

buzzer 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.22
OBJECT IDENTIFIER    

brPrtAdvancedErrorBuzzer 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.22.1
Error Buzzer
OBJECT-TYPE    
  INTEGER off(1), normal(2), special(3)  

brPrtAdvancedPanelBuzzer 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.22.2
Panel Buzzer
OBJECT-TYPE    
  INTEGER off(1), on(2)  

brPrtAdvancedBuzzerVolume 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.22.3
Buzzer Volume
OBJECT-TYPE    
  INTEGER high(1), low(2)  

brPrtAdvancedLCDDensity 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.23
LCDDensity
OBJECT-TYPE    
  INTEGER  

smallPaperSize 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.51
OBJECT IDENTIFIER    

brSmallPaperSizeMP 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.51.1
MP Tray Small Paper size. 1:Executive 2:Letter 3:Legal 24:A6 25:A5 26:A4 27:A3(ISO) 45:B5(JIS) 46:B4(JIS) 80:Monarch 81:COM10 90:DL 91:C5 99:B6 100:B5 890:LEDGER 891:A3PLUS(13x19) 892:Letter Short Edge 893:A4 Short Edge 894:A4LONG 895:Executive Short Edge 896:B5(ISO) Short Edge 897:CUSTOM 898:A4/Letter 899:B5/Executive 900:Envelopes 901:DL-L 902:HAGAKI 903:FOLIO 904:ORGANIZER J 905:ORGANIZER K 906:ORGANIZER L 907:ORGANIZER M 908:USER DEFINED 911:Detect Sensor 1000:No Casette
OBJECT-TYPE    
  INTEGER executive(1), letter(2), legal(3), a6(24), a5(25), a4(26), a3ISO(27), b5JIS(45), b4JIS(46), monarch(80), com10(81), dl(90), c5(91), b6(99), b5(100), ledger(890), a3PLUS(891), letterShortEdge(892), a4ShortEdge(893), a4LONG(894), executiveShortEdge(895), b5ISOShortEdge(896), custom(897), a4Letter(898), b5Executive(899), envelopes(900), dll(901), hagaki(902), folio(903), organaizerJ(904), organaizerK(905), organaizerL(906), organaizerM(907), userdefined(908), detectsensor(911), inches3x5(920), envelopesY4(921), largestEnvelopesTheWest(922), noCasette(1000)  

brSmallPaperSize1 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.51.2
Tray1 Small Paper size. 1:Executive 2:Letter 3:Legal 24:A6 25:A5 26:A4 27:A3(ISO) 45:B5(JIS) 46:B4(JIS) 80:Monarch 81:COM10 90:DL 91:C5 99:B6 100:B5 890:LEDGER 891:A3PLUS(13x19) 892:Letter Short Edge 893:A4 Short Edge 894:A4LONG 895:Executive Short Edge 896:B5(ISO) Short Edge 897:CUSTOM 898:A4/Letter 899:B5/Executive 900:Envelopes 901:DL-L 902:HAGAKI 903:FOLIO 904:ORGANIZER J 905:ORGANIZER K 906:ORGANIZER L 907:ORGANIZER M 908:USER DEFINED 911:Detect Sensor 1000:No Casette
OBJECT-TYPE    
  INTEGER executive(1), letter(2), legal(3), a6(24), a5(25), a4(26), a3ISO(27), b5JIS(45), b4JIS(46), monarch(80), com10(81), dl(90), c5(91), b6(99), b5(100), ledger(890), a3PLUS(891), letterShortEdge(892), a4ShortEdge(893), a4LONG(894), executiveShortEdge(895), b5ISOShortEdge(896), custom(897), a4Letter(898), b5Executive(899), envelopes(900), dll(901), hagaki(902), folio(903), organaizerJ(904), organaizerK(905), organaizerL(906), organaizerM(907), userdefined(908), detectsensor(911), inches3x5(920), envelopesY4(921), largestEnvelopesTheWest(922), noCasette(1000)  

brSmallPaperSize2 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.51.3
Tray2 Small Paper size. 1:Executive 2:Letter 3:Legal 24:A6 25:A5 26:A4 27:A3(ISO) 45:B5(JIS) 46:B4(JIS) 80:Monarch 81:COM10 90:DL 91:C5 99:B6 100:B5 890:LEDGER 891:A3PLUS(13x19) 892:Letter Short Edge 893:A4 Short Edge 894:A4LONG 895:Executive Short Edge 896:B5(ISO) Short Edge 897:CUSTOM 898:A4/Letter 899:B5/Executive 900:Envelopes 901:DL-L 902:HAGAKI 903:FOLIO 904:ORGANIZER J 905:ORGANIZER K 906:ORGANIZER L 907:ORGANIZER M 908:USER DEFINED 911:Detect Sensor 1000:No Casette
OBJECT-TYPE    
  INTEGER executive(1), letter(2), legal(3), a6(24), a5(25), a4(26), a3ISO(27), b5JIS(45), b4JIS(46), monarch(80), com10(81), dl(90), c5(91), b6(99), b5(100), ledger(890), a3PLUS(891), letterShortEdge(892), a4ShortEdge(893), a4LONG(894), executiveShortEdge(895), b5ISOShortEdge(896), custom(897), a4Letter(898), b5Executive(899), envelopes(900), dll(901), hagaki(902), folio(903), organaizerJ(904), organaizerK(905), organaizerL(906), organaizerM(907), userdefined(908), detectsensor(911), inches3x5(920), envelopesY4(921), largestEnvelopesTheWest(922), noCasette(1000)  

brSmallPaperSize3 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.51.4
Tray3 Small Paper size. 1:Executive 2:Letter 3:Legal 24:A6 25:A5 26:A4 27:A3(ISO) 45:B5(JIS) 46:B4(JIS) 80:Monarch 81:COM10 90:DL 91:C5 99:B6 100:B5 890:LEDGER 891:A3PLUS(13x19) 892:Letter Short Edge 893:A4 Short Edge 894:A4LONG 895:Executive Short Edge 896:B5(ISO) Short Edge 897:CUSTOM 898:A4/Letter 899:B5/Executive 900:Envelopes 901:DL-L 902:HAGAKI 903:FOLIO 904:ORGANIZER J 905:ORGANIZER K 906:ORGANIZER L 907:ORGANIZER M 908:USER DEFINED 911:Detect Sensor 1000:No Casette
OBJECT-TYPE    
  INTEGER executive(1), letter(2), legal(3), a6(24), a5(25), a4(26), a3ISO(27), b5JIS(45), b4JIS(46), monarch(80), com10(81), dl(90), c5(91), b6(99), b5(100), ledger(890), a3PLUS(891), letterShortEdge(892), a4ShortEdge(893), a4LONG(894), executiveShortEdge(895), b5ISOShortEdge(896), custom(897), a4Letter(898), b5Executive(899), envelopes(900), dll(901), hagaki(902), folio(903), organaizerJ(904), organaizerK(905), organaizerL(906), organaizerM(907), userdefined(908), detectsensor(911), inches3x5(920), envelopesY4(921), largestEnvelopesTheWest(922), noCasette(1000)  

brSmallPaperSize4 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.51.5
Tray4 Small Paper size. 1:Executive 2:Letter 3:Legal 24:A6 25:A5 26:A4 27:A3(ISO) 45:B5(JIS) 46:B4(JIS) 80:Monarch 81:COM10 90:DL 91:C5 99:B6 100:B5 890:LEDGER 891:A3PLUS(13x19) 892:Letter Short Edge 893:A4 Short Edge 894:A4LONG 895:Executive Short Edge 896:B5(ISO) Short Edge 897:CUSTOM 898:A4/Letter 899:B5/Executive 900:Envelopes 901:DL-L 902:HAGAKI 903:FOLIO 904:ORGANIZER J 905:ORGANIZER K 906:ORGANIZER L 907:ORGANIZER M 908:USER DEFINED 911:Detect Sensor 1000:No Casette
OBJECT-TYPE    
  INTEGER executive(1), letter(2), legal(3), a6(24), a5(25), a4(26), a3ISO(27), b5JIS(45), b4JIS(46), monarch(80), com10(81), dl(90), c5(91), b6(99), b5(100), ledger(890), a3PLUS(891), letterShortEdge(892), a4ShortEdge(893), a4LONG(894), executiveShortEdge(895), b5ISOShortEdge(896), custom(897), a4Letter(898), b5Executive(899), envelopes(900), dll(901), hagaki(902), folio(903), organaizerJ(904), organaizerK(905), organaizerL(906), organaizerM(907), userdefined(908), detectsensor(911), inches3x5(920), envelopesY4(921), largestEnvelopesTheWest(922), noCasette(1000)  

trayPriority 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.52
OBJECT IDENTIFIER    

brPrtAdvancedTrayPriority 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.52.1
The value of brTrayPriorityIndex corresponding to the default setting.
OBJECT-TYPE    
  INTEGER  

brTrayPriorityCount 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.52.2
Maximum number of TrayPriority INDEX.
OBJECT-TYPE    
  INTEGER  

brTrayPriorityTable 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.52.3
This table represents TrayPriority setting.
OBJECT-TYPE    
  SEQUENCE OF  
    BrTrayPriorityEntry

brTrayPriorityEntry 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.52.3.1
A row in the TrayPriority table. Rows cannot be created or deleted.
OBJECT-TYPE    
  BrTrayPriorityEntry  

brTrayPriorityIndex 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.52.3.1.1
The number.
OBJECT-TYPE    
  INTEGER 1..255  

brTrayPriorityMember 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.52.3.1.2
The TrayPriority member data. Format: valulen(1byte), value(valulen byte)
OBJECT-TYPE    
  OCTET STRING  

carbonCopy 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.53
OBJECT IDENTIFIER    

brCarbonCopyMode 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.53.1
Carbon Copy mode setting.
OBJECT-TYPE    
  INTEGER off(1), on(2), auto(3), parallel(4)  

brCarbonCopies 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.53.2
The copies setting of Carbon Copy function.
OBJECT-TYPE    
  INTEGER  

brCarbonCopyTable 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.53.10
This table represents CarbonCopy setting.
OBJECT-TYPE    
  SEQUENCE OF  
    BrCarbonCopyEntry

brCarbonCopyEntry 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.53.10.1
A row in the CarbonCopy table. Rows cannot be created or deleted.
OBJECT-TYPE    
  BrCarbonCopyEntry  

brCarbonCopyIndex 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.53.10.1.1
The number.
OBJECT-TYPE    
  INTEGER 1..65535  

brCarbonCopyTray 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.53.10.1.2
Copy Tray setting.
OBJECT-TYPE    
  INTEGER tray1(1), tray2(2), tray3(3), tray4(4), mpTray(10), auto(11)  

brCarbonCopyMacro 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.53.10.1.3
Carbon Copy Macro Setting
OBJECT-TYPE    
  INTEGER off(1), on(2)  

brCarbonCopyMacroID 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.53.10.1.4
Carbon Copy Macro ID Setting
OBJECT-TYPE    
  INTEGER  

mediaFix 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.54
OBJECT IDENTIFIER    

brMediaFixTray1 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.54.1
Media Fix setting for tray1.
OBJECT-TYPE    
  INTEGER off(1), regular(2), thick(3), thicker(4), transparency(5), thin(6), bond(7), envelopes(8), envThick(9), envThin(10), recycled(11)  

brMediaFixTray2 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.54.2
Media Fix setting for tray2.
OBJECT-TYPE    
  INTEGER off(1), regular(2), thick(3), thicker(4), transparency(5), thin(6), bond(7), envelopes(8), envThick(9), envThin(10), recycled(11)  

brMediaFixTray3 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.54.3
Media Fix setting for tray3.
OBJECT-TYPE    
  INTEGER off(1), regular(2), thick(3), thicker(4), transparency(5), thin(6), bond(7), envelopes(8), envThick(9), envThin(10), recycled(11)  

brMediaFixTray4 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.54.4
Media Fix setting for tray4.
OBJECT-TYPE    
  INTEGER off(1), regular(2), thick(3), thicker(4), transparency(5), thin(6), bond(7), envelopes(8), envThick(9), envThin(10), recycled(11)  

brMediaFixMP 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.54.10
Media Fix setting for MPtray.
OBJECT-TYPE    
  INTEGER off(1), regular(2), thick(3), thicker(4), transparency(5), thin(6), bond(7), envelopes(8), envThick(9), envThin(10), recycled(11)  

directprint 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.60
OBJECT IDENTIFIER    

brDirectPrintPaperSize 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.60.1
Default Paper size. -1:No Casette 1:Executive 2:Letter 3:Legal 24:A6 25:A5 26:A4 27:A3(ISO) 45:B5(JIS) 46:B4(JIS) 80:Monarch 81:COM10 90:DL 91:C5 99:B6 100:B5 890:LEDGER 891:A3PLUS(13x19) 892:Letter Short Edge 893:A4 Short Edge 894:A4LONG 895:Executive Short Edge 896:B5(ISO) Short Edge 897:CUSTOM (ANY) 898:A4/Letter 899:B5/Executive 900:Envelopes 901:DL-L 902:HAGAKI 903:FOLIO 904:ORGANIZER J 905:ORGANIZER K 906:ORGANIZER L 907:ORGANIZER M 908:USER DEFINED 911:Detect Sensor 920:3x5(inches) 921:Envelopes Y4 922:Largest envelopes of the West 923:A5L 924:B6JIS 925:16K195x270 926:16k184x260 927:16k197x273
OBJECT-TYPE    
  INTEGER executive(1), letter(2), legal(3), a6(24), a5(25), a4(26), a3ISO(27), b5JIS(45), b4JIS(46), monarch(80), com10(81), dl(90), c5(91), b6(99), b5(100), ledger(890), a3PLUS(891), letterShortEdge(892), a4ShortEdge(893), a4LONG(894), executiveShortEdge(895), b5ISOShortEdge(896), custom(897), a4Letter(898), b5Executive(899), envelopes(900), dll(901), hagaki(902), folio(903), organaizerJ(904), organaizerK(905), organaizerL(906), organaizerM(907), userdefined(908), detectsensor(911), inches3x5(920), envelopesY4(921), largestEnvelopesTheWest(922), a5l(923), b6jis(924), prc16k195x270(925), prc16k184x260(926), prc16k197x273(927)  

brDirectPrintMediaType 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.60.2
Default Media type. 0:Regular 1:Thick paper 2:Thicker paper 3:Transparency 4:Thin paper 5:Bond paper 6:ENVELOPES 7:ENV. THICK 8:ENV. THIN 9:RECYCLED 10:HAGAKI 11:LABEL 1nd (default) Tray PaperType
OBJECT-TYPE    
  INTEGER  

brDirectPrintMultipulPage 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.60.3
OBJECT-TYPE    
  INTEGER  

brDirectPrintOrientation 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.60.4
OBJECT-TYPE    
  INTEGER  

brDirectPrintCollate 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.60.5
OBJECT-TYPE    
  INTEGER  

brDirectPrintOutputColor 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.60.6
OBJECT-TYPE    
  INTEGER  

brDirectPrintPrintQuality 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.60.7
OBJECT-TYPE    
  INTEGER  

brDirectPrintPdfOption 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.60.8
OBJECT-TYPE    
  INTEGER  

brDirectPrintSetting 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.60.9
OBJECT-TYPE    
  INTEGER  

brDirectPrintPdfThumbnailType 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.60.10
PDF Thumbnail Type 1:AlternativeImage 2:ReductionImage
OBJECT-TYPE    
  INTEGER alternativeImage(1), reductionImage(2)  

pictbridge 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.61
OBJECT IDENTIFIER    

brPictBridgePaperSize 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.61.1
Default Paper size. -1:No Casette 1:Executive 2:Letter 3:Legal 24:A6 25:A5 26:A4 27:A3(ISO) 45:B5(JIS) 46:B4(JIS) 80:Monarch 81:COM10 90:DL 91:C5 99:B6 100:B5 890:LEDGER 891:A3PLUS(13x19) 892:Letter Short Edge 893:A4 Short Edge 894:A4LONG 895:Executive Short Edge 896:B5(ISO) Short Edge 897:CUSTOM (ANY) 898:A4/Letter 899:B5/Executive 900:Envelopes 901:DL-L 902:HAGAKI 903:FOLIO 904:ORGANIZER J 905:ORGANIZER K 906:ORGANIZER L 907:ORGANIZER M 908:USER DEFINED 911:Detect Sensor 920:3x5(inches) 921:Envelopes Y4 922:Largest envelopes of the West
OBJECT-TYPE    
  INTEGER executive(1), letter(2), legal(3), a6(24), a5(25), a4(26), a3ISO(27), b5JIS(45), b4JIS(46), monarch(80), com10(81), dl(90), c5(91), b6(99), b5(100), ledger(890), a3PLUS(891), letterShortEdge(892), a4ShortEdge(893), a4LONG(894), executiveShortEdge(895), b5ISOShortEdge(896), custom(897), a4Letter(898), b5Executive(899), envelopes(900), dll(901), hagaki(902), folio(903), organaizerJ(904), organaizerK(905), organaizerL(906), organaizerM(907), userdefined(908), detectsensor(911), inches3x5(920), envelopesY4(921), largestEnvelopesTheWest(922)  

brPictBridgeOrientation 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.61.2
OBJECT-TYPE    
  INTEGER  

brPictBridgeDateTime 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.61.3
OBJECT-TYPE    
  INTEGER  

brPictBridgeFileName 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.61.4
OBJECT-TYPE    
  INTEGER  

brPictBridgePrintQuality 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.61.5
OBJECT-TYPE    
  INTEGER  

brPictBridgePrintSetting 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.61.6
OBJECT-TYPE    
  INTEGER  

colorcorrection 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.62
OBJECT IDENTIFIER    

brColorCalibration 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.62.1
OBJECT-TYPE    
  INTEGER  

brColorCalibrationReset 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.62.2
OBJECT-TYPE    
  INTEGER  

brAutoRegistRegistrate 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.62.3
OBJECT-TYPE    
  INTEGER  

brAutoRegistSetInterval 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.62.4
OBJECT-TYPE    
  INTEGER  

brRegistrationPrintChart 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.62.5
OBJECT-TYPE    
  INTEGER  

brRegistrationXMagentaLeft 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.62.6
OBJECT-TYPE    
  INTEGER  

brRegistrationXMagentaRight 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.62.7
OBJECT-TYPE    
  INTEGER  

brRegistrationXCyanLeft 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.62.8
OBJECT-TYPE    
  INTEGER  

brRegistrationXCyanRight 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.62.9
OBJECT-TYPE    
  INTEGER  

brRegistrationXYellowLeft 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.62.10
OBJECT-TYPE    
  INTEGER  

brRegistrationXYellowRight 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.62.11
OBJECT-TYPE    
  INTEGER  

brRegistrationYMagenta 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.62.12
OBJECT-TYPE    
  INTEGER  

brRegistrationYCyan 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.62.13
OBJECT-TYPE    
  INTEGER  

brRegistrationYYellow 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.62.14
OBJECT-TYPE    
  INTEGER  

funclock 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63
OBJECT IDENTIFIER    

brFuncLockSettingInit 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.1
Init Function Lock Setting.
OBJECT-TYPE    
  INTEGER  

brFuncLockAdminPassword 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.2
Get or Set the administrator password of Function Lock.
OBJECT-TYPE    
  DisplayString  

brFuncLock 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.3
Get or Set the status of Function Lock.
OBJECT-TYPE    
  INTEGER 1..2  

brFuncLockPublicFuncCount 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.4
Return the number of functions to be locked on the public mode.
OBJECT-TYPE    
  INTEGER 0..2147483647  

brFuncLockPublicTable 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.5
OBJECT-TYPE    
  SEQUENCE OF  
    BrFuncLockPublicEntry

brFuncLockPublicEntry 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.5.1
OBJECT-TYPE    
  BrFuncLockPublicEntry  

brFuncLockPublicFuncIndex 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.5.1.1
Return the index value of functions to be locked on the public mode.
OBJECT-TYPE    
  INTEGER 1..2147483647  

brFuncLockPublicFuncMember 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.5.1.2
Return the member of functions to be locked on the public mode.
OBJECT-TYPE    
  INTEGER copycolor(1), copybr(2), faxtx(3), faxrx(4), scan(5), print(6), pcc(7)  

brFuncLockPublicFuncSupported 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.5.1.3
Return the status of availableness of functions to be locked on the public mode.
OBJECT-TYPE    
  INTEGER 0..1  

brFuncLockPublicFuncEnable 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.5.1.4
Get of Set the status of functions on the public mode.
OBJECT-TYPE    
  INTEGER 0..1  

brFuncLockUserCount 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.6
Return the number of users to be locked on function lock.
OBJECT-TYPE    
  INTEGER 0..2147483647  

brFuncLockUserTable 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.7
OBJECT-TYPE    
  SEQUENCE OF  
    BrFuncLockUserEntry

brFuncLockUserEntry 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.7.1
OBJECT-TYPE    
  BrFuncLockUserEntry  

brFuncLockUserIndex 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.7.1.1
Return the index value of users to be locked on function lock.
OBJECT-TYPE    
  INTEGER 1..2147483647  

brFuncLockUserName 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.7.1.2
Get or Set the user name of function lock.
OBJECT-TYPE    
  DisplayString  

brFuncLockUserPassword 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.7.1.3
Get or Set the user password of function lock.
OBJECT-TYPE    
  DisplayString  

brFuncLockUserFuncCount 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.8
Return the number of users to be locked on the function lock.
OBJECT-TYPE    
  INTEGER 0..2147483647  

brFuncLockUserFuncTable 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.9
OBJECT-TYPE    
  SEQUENCE OF  
    BrFuncLockUserFuncEntry

brFuncLockUserFuncEntry 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.9.1
OBJECT-TYPE    
  BrFuncLockUserFuncEntry  

brFuncLockUserFuncIndex 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.9.1.1
Return the index value of users to be locked on user mode.
OBJECT-TYPE    
  INTEGER 1..2147483647  

brFuncLockUserFuncMember 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.9.1.2
Return the function numbers to be locked on user mode.
OBJECT-TYPE    
  INTEGER copycolor(1), copybr(2), faxtx(3), faxrx(4), scan(5), print(6), pcc(7)  

brFuncLockUserFuncSupported 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.9.1.3
Return the availableness of function to be locked on user mode.
OBJECT-TYPE    
  INTEGER 0..1  

brFuncLockUserFuncEnable 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.9.1.4
Get or Set the lock status on the user mode.
OBJECT-TYPE    
  INTEGER 0..1  

brFuncLockSetting 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.10
Write the all information of function lock.
OBJECT-TYPE    
  INTEGER  

brFuncLockUserPrintPageCounterReset 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.20
Reset all user's counter of Color/Mono print page.
OBJECT-TYPE    
  INTEGER 0..0  

brFuncLockPublicPrintLimitEnable 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.21
This MIB represents Enable/Disable of print limit setting for public user.
OBJECT-TYPE    
  INTEGER 0..1  

brFuncLockPublicPrintPageMax 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.22
The Maximum of print limited for public user.
OBJECT-TYPE    
  INTEGER 1..999999  

brFuncLockPublicPrintPageCountMono 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.23
The counter of monochrome print page.
OBJECT-TYPE    
  INTEGER 0..999999  

brFuncLockPublicPrintPageCountColor 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.24
The counter of color print page for public user.
OBJECT-TYPE    
  INTEGER 0..999999  

brFuncLockUserPrintPageTable 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.25
OBJECT-TYPE    
  SEQUENCE OF  
    BrFuncLockUserPrintPageEntry

brFuncLockUserPrintPageEntry 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.25.1
OBJECT-TYPE    
  BrFuncLockUserPrintPageEntry  

brFuncLockUserPrintPageIndex 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.25.1.1
OBJECT-TYPE    
  INTEGER 1..2147483647  

brFuncLockUserPrintPageLimitEnable 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.25.1.2
The Maximum of Print Page setting for user.
OBJECT-TYPE    
  INTEGER 0..1  

brFuncLockUserPrintPageCountMono 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.25.1.3
The Counter of Monochrome Print Page for user.
OBJECT-TYPE    
  INTEGER 0..999999  

brFuncLockUserPrintPageCountColor 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.25.1.4
The counter of color print page for user.
OBJECT-TYPE    
  INTEGER 0..999999  

brFuncLockUserPrintPageMax 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.25.1.5
The Maximum of print limited for user.
OBJECT-TYPE    
  INTEGER 1..999999  

brFuncLockUserPrintPageCountMonoLast 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.25.1.6
OBJECT-TYPE    
  INTEGER 0..999999  

brFuncLockUserPrintPageCountColorLast 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.25.1.7
OBJECT-TYPE    
  INTEGER 0..999999  

brFuncLockPcLoginNameAuthEnable 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.26
This MIB represents Enable/Disable of PC Login Authentication setting.
OBJECT-TYPE    
  INTEGER 0..1  

brFuncLockPcLoginNameAuthCount 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.27
The number of PC Login Name.
OBJECT-TYPE    
  INTEGER  

brFuncLockPcLoginNameTable 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.28
OBJECT-TYPE    
  SEQUENCE OF  
    BrFuncLockPcLoginNameEntry

brFuncLockPcLoginNameEntry 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.28.1
OBJECT-TYPE    
  BrFuncLockPcLoginNameEntry  

brFuncLockPcLoginNameAuthIndex 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.28.1.1
OBJECT-TYPE    
  INTEGER 1..50  

brFuncLockPcLoginName 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.28.1.2
The PC Login Name.
OBJECT-TYPE    
  OCTET STRING  

brFuncLockPcLoginNameAuthID 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.28.1.3
PC Login ID for PC Login name.
OBJECT-TYPE    
  INTEGER 1..25  

brFuncLockPublicPrintPageCountMonoLast 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.29
OBJECT-TYPE    
  INTEGER 0..999999  

brFuncLockPublicPrintPageCountColorLast 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.30
OBJECT-TYPE    
  INTEGER 0..999999  

autocountreset 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.31
OBJECT IDENTIFIER    

brFuncLockAutoCountResetFrequency 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.31.1
OBJECT-TYPE    
  INTEGER 1..4  

brFuncLockAutoCountResetTime 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.31.2
OBJECT-TYPE    
  OCTET STRING SIZE(2..2)  

brFuncLockAutoCountResetWeek 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.31.3
OBJECT-TYPE    
  INTEGER 1..7  

brFuncLockAutoCountResetDate 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.31.4
OBJECT-TYPE    
  INTEGER 1..31  

mail 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.3
OBJECT IDENTIFIER    

brPrtMailbox 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.3.1
Mailbox Installed of not
OBJECT-TYPE    
  INTEGER 0..2  

brPrtMailboxProtectTable 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.3.2
unused
OBJECT-TYPE    
  SEQUENCE OF  
    BrPrtMailboxProtectEntry

brPrtMailboxProtectEntry 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.3.2.1
unused
OBJECT-TYPE    
  BrPrtMailboxProtectEntry  

brPrtMailboxProtectIndex 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.3.2.1.1
unused
OBJECT-TYPE    
  INTEGER 1..65535  

brPrtMailboxProtect 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.3.2.1.2
unused
OBJECT-TYPE    
  INTEGER 0..2  

brPrtAvoidMailboxFullTable 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.3.3
unused
OBJECT-TYPE    
  SEQUENCE OF  
    BrPrtAvoidMailboxFullEntry

brPrtAvoidMailboxFullEntry 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.3.3.1
unused
OBJECT-TYPE    
  BrPrtAvoidMailboxFullEntry  

brPrtAvoidMailboxFullIndex 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.3.3.1.1
unused
OBJECT-TYPE    
  INTEGER 1..65535  

brPrtAvoidMailboxFull 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.3.3.1.2
unused
OBJECT-TYPE    
  INTEGER 0..2  

brPrtMailboxOutbin 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.3.4
Outbin
OBJECT-TYPE    
  INTEGER 0..110  

brPrtMailboxProtectGroup 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.3.5
Mailbox Protect
OBJECT-TYPE    
  INTEGER 0..99  

brPrtAvoidMailboxFullGroup 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.3.6
Avoid Mailbox Full
OBJECT-TYPE    
  INTEGER 0..1  

finisher 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.4
OBJECT IDENTIFIER    

brPrtFinisher 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.4.1
Finisher type 0:no finisher 1:FS5050 2:FS5100
OBJECT-TYPE    
  INTEGER 0..255  

catch-tray 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.5
OBJECT IDENTIFIER    

brPrtCatchTray 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.5.1
catch tray Installed or not
OBJECT-TYPE    
  INTEGER 0..2  

pagesetup 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2
OBJECT IDENTIFIER    

pcl 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.1
OBJECT IDENTIFIER    

margin-p 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.1.1
OBJECT IDENTIFIER    

brPagePCLLeftMargin 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.1.1.1
PCL LeftMargin 1270N :0-145 2400Ce :0-176
OBJECT-TYPE    
  INTEGER 0..255  

brPagePCLRightMargin 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.1.1.2
PCL RightMargin 1270N :10-155 2400Ce :10-186
OBJECT-TYPE    
  INTEGER 0..255  

brPagePCLTopMargin 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.1.1.3
PCL TopMargin 0:0 33:0.33 50:0.5 100:1.0 150:1.5 200:2.0
OBJECT-TYPE    
  INTEGER 0..200  

brPagePCLBottomMargin 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.1.1.4
PCL BottomMargin 0:0 33:0.33 50:0.5 100:1.0 150:1.5 200:2.0
OBJECT-TYPE    
  INTEGER 0..200  

brPagePCLLines 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.1.1.5
PCL Form Line 5-128
OBJECT-TYPE    
  INTEGER 5..128  

auto-p 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.1.2
OBJECT IDENTIFIER    

brPagePCLAutoLF 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.1.2.1
PCL AutoLF 1:Off 2:On
OBJECT-TYPE    
  INTEGER 0..2  

brPagePCLAutoCR 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.1.2.2
PCL AutoCR 1:Off 2:On
OBJECT-TYPE    
  INTEGER 0..2  

brPagePCLAutoWrap 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.1.2.3
PCL AutoWrap 1:Off 2:On
OBJECT-TYPE    
  INTEGER 0..2  

brPagePCLAutoSkip 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.1.2.4
PCL AutoSkip 1:Off 2:On
OBJECT-TYPE    
  INTEGER 0..2  

ps 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.2
OBJECT IDENTIFIER    

brPagePSPrintPSError 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.2.1
PrintPSError 1:Off 2:On
OBJECT-TYPE    
  INTEGER off(1), on(2)  

brPagePSKeepPCLFonts 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.2.2
KeepPCLFonts 1:Off 2:On
OBJECT-TYPE    
  INTEGER off(1), on(2)  

brPagePSCAPTsetting 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.2.3
PS CAPT setting 1:Off 2:On
OBJECT-TYPE    
  INTEGER off(1), on(2)  

gl 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.3
OBJECT IDENTIFIER    

pen1 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.3.1
OBJECT IDENTIFIER    

brPageGLPen1Size 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.3.1.1
GL PenSize 1-16
OBJECT-TYPE    
  INTEGER 0..16  

brPageGLPen1GrayLevel 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.3.1.2
GLPen GrayLevel 0:15% 1:30% 2:45% 3:75% 4:90% 5:100%
OBJECT-TYPE    
  INTEGER 0..5  

pen2 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.3.2
OBJECT IDENTIFIER    

brPageGLPen2Size 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.3.2.1
GL PenSize 1-16
OBJECT-TYPE    
  INTEGER 0..16  

brPageGLPen2GrayLevel 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.3.2.2
GLPen GrayLevel 0:15% 1:30% 2:45% 3:75% 4:90% 5:100%
OBJECT-TYPE    
  INTEGER 0..5  

pen3 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.3.3
OBJECT IDENTIFIER    

brPageGLPen3Size 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.3.3.1
GL PenSize 1-16
OBJECT-TYPE    
  INTEGER 0..16  

brPageGLPen3GrayLevel 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.3.3.2
GLPen GrayLevel 0:15% 1:30% 2:45% 3:75% 4:90% 5:100%
OBJECT-TYPE    
  INTEGER 0..5  

pen4 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.3.4
OBJECT IDENTIFIER    

brPageGLPen4Size 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.3.4.1
GL PenSize 1-16
OBJECT-TYPE    
  INTEGER 0..16  

brPageGLPen4GrayLevel 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.3.4.2
GLPen GrayLevel 0:15% 1:30% 2:45% 3:75% 4:90% 5:100%
OBJECT-TYPE    
  INTEGER 0..5  

pen5 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.3.5
OBJECT IDENTIFIER    

brPageGLPen5Size 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.3.5.1
GL PenSize 1-16
OBJECT-TYPE    
  INTEGER 0..16  

brPageGLPen5GrayLevel 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.3.5.2
OBJECT-TYPE    
  INTEGER 0..5  

pen6 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.3.6
OBJECT IDENTIFIER    

brPageGLPen6Size 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.3.6.1
GL PenSize 1-16
OBJECT-TYPE    
  INTEGER 0..16  

brPageGLPen6GrayLevel 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.3.6.2
GLPen GrayLevel 0:15% 1:30% 2:45% 3:75% 4:90% 5:100%
OBJECT-TYPE    
  INTEGER 0..5  

epson 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.4
OBJECT IDENTIFIER    

margin-e 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.4.1
OBJECT IDENTIFIER    

brPageEPSONLeftMargin 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.4.1.1
EPSON LeftMargin 1270N :0-145 2400Ce :0-176
OBJECT-TYPE    
  INTEGER 0..255  

brPageEPSONRightMargin 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.4.1.2
EPSON RightMargin 1270N :10-155 2400Ce :10-186
OBJECT-TYPE    
  INTEGER 0..255  

brPageEPSONTopMargin 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.4.1.3
EPSON TopMargin 0:0 33:0.33 50:0.5 100:1.0 150:1.5 200:2.0
OBJECT-TYPE    
  INTEGER 0..200  

brPageEPSONBottomMargin 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.4.1.4
EPSON BottomMargin 0:0 33:0.33 50:0.5 100:1.0 150:1.5 200:2.0
OBJECT-TYPE    
  INTEGER 0..200  

brPageEPSONLines 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.4.1.5
EPSON Form Line 5-128
OBJECT-TYPE    
  INTEGER 5..128  

auto-e 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.4.2
OBJECT IDENTIFIER    

brPageEPSONAutoLF 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.4.2.1
EPSON AutoLF 1:Off 2:On
OBJECT-TYPE    
  INTEGER 0..2  

brPageEPSONAutoMask 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.4.2.5
EPSON AutoMask 1:Off 2:On
OBJECT-TYPE    
  INTEGER 0..2  

ibm 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.5
OBJECT IDENTIFIER    

margin-i 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.5.1
OBJECT IDENTIFIER    

brPageIBMLeftMargin 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.5.1.1
IBM LeftMargin 1270N :0-145 2400Ce :0-176
OBJECT-TYPE    
  INTEGER 0..255  

brPageIBMRightMargin 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.5.1.2
IBM LeftMargin 1270N :10-155 2400Ce :10-186
OBJECT-TYPE    
  INTEGER 0..255  

brPageIBMTopMargin 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.5.1.3
IBM BottomMargin 0:0 33:0.33 50:0.5 100:1.0 150:1.5 200:2.0
OBJECT-TYPE    
  INTEGER 0..200  

brPageIBMBottomMargin 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.5.1.4
IBM BottomMargin 0:0 33:0.33 50:0.5 100:1.0 150:1.5 200:2.0
OBJECT-TYPE    
  INTEGER 0..200  

brPageIBMLines 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.5.1.5
IBM Form Line 5-128
OBJECT-TYPE    
  INTEGER 5..128  

auto-i 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.5.2
OBJECT IDENTIFIER    

brPageIBMAutoLF 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.5.2.1
IBM AutoLF 1:Off 2:On
OBJECT-TYPE    
  INTEGER 0..2  

brPageIBMAutoCR 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.5.2.2
IBM AutoCR 1:Off 2:On
OBJECT-TYPE    
  INTEGER 0..2  

brPageIBMAutoMask 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.5.2.5
IBM AutoMask 1:Off 2:On
OBJECT-TYPE    
  INTEGER 0..2  

fontsetup 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.3
OBJECT IDENTIFIER    

brFontName 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.3.1
unused
OBJECT-TYPE    
  INTEGER 0..99999  

brFontPointSize 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.3.2
unused(400-99975)
OBJECT-TYPE    
  INTEGER 4..99999  

brFontPitch 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.3.3
unused(44-9999)
OBJECT-TYPE    
  INTEGER 0..9999  

brFontSymbolSet 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.3.4
unused
OBJECT-TYPE    
  INTEGER 0..99999  

controlpanel 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4
OBJECT IDENTIFIER    

reset 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.1
OBJECT IDENTIFIER    

brPanelResetUser 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.1.1
User Reset
OBJECT-TYPE    
  INTEGER 0..100  

brPanelResetFactory 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.1.2
Factory Reset
OBJECT-TYPE    
  INTEGER 0..100  

test 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.2
OBJECT IDENTIFIER    

brPanelTestConfiguration 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.2.1
Print Config page
OBJECT-TYPE    
  INTEGER 0..100  

brPanelTestFontList 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.2.2
Print Fonts list
OBJECT-TYPE    
  INTEGER 0..100  

brPanelTestTestPage 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.2.3
Print Test page
OBJECT-TYPE    
  INTEGER 0..100  

brPanelTestDemoPage 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.2.4
Print Demo page 0:Enable Print Demo page 1:Disable Print Demo page
OBJECT-TYPE    
  INTEGER 0..100  

panellock 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.3
OBJECT IDENTIFIER    

brPanelLockPasswd 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.3.1
unused
OBJECT-TYPE    
  INTEGER 0..100  

brPanelLock 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.3.2
The state of panel lock
OBJECT-TYPE    
  INTEGER off(1), on(2)  

brPanelLockOn 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.3.3
Panel Lock by setting a password.
OBJECT-TYPE    
  OCTET STRING  

brPanelLockOff 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.3.4
Panel Lock is canceled by inputting a password..
OBJECT-TYPE    
  OCTET STRING  

key 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.4
OBJECT IDENTIFIER    

brPanelKeyOnline 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.4.1
Press Online Key
OBJECT-TYPE    
  INTEGER 0..1  

brPanelKeyFormFeed 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.4.2
Press FormFeed Key
OBJECT-TYPE    
  INTEGER 0..1  

brPanelKeyContinue 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.4.3
Press Countinue Key
OBJECT-TYPE    
  INTEGER 0..1  

brPanelKeyMode 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.4.4
unused
OBJECT-TYPE    
  INTEGER 0..1  

brPanelKeyGo 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.4.5
Press Go Key
OBJECT-TYPE    
  INTEGER 0..1  

brPanelKeyJobCancel 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.4.6
Press JobCancel Key
OBJECT-TYPE    
  INTEGER 0..1  

brPanelKeyReprint 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.4.7
Press Reprint Key
OBJECT-TYPE    
  INTEGER 0..1  

brPanelKeySecure 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.4.8
Press SecurePrint Key
OBJECT-TYPE    
  INTEGER 0..1  

panelinfo 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.5
OBJECT IDENTIFIER    

brLCDMode1 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.5.1
LCD Display Mode. 1:fix 2:blink 3:scroll
OBJECT-TYPE    
  INTEGER fix(1), blink(2), scroll(3), blinkScroll(4)  

brLCDString1 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.5.2
LCD Display String of first line.
OBJECT-TYPE    
  OCTET STRING  

brLCDMode2 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.5.3
LCD Display Mode. 1:fix 2:blink 3:scroll
OBJECT-TYPE    
  INTEGER fix(1), blink(2), scroll(3)  

brLCDString2 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.5.4
LCD Display String of second line.
OBJECT-TYPE    
  OCTET STRING  

brLCDString16fix 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.5.5
LCD Display String of 16fix.
OBJECT-TYPE    
  DisplayString  

brBackLightColor 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.5.6
LCD Display Mode. 0:Off 1:Green 2:Orange 3:Red
OBJECT-TYPE    
  INTEGER green(1), orange(2), red(3), notsupport(255)  

brLCDMode3 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.5.7
LCD Display Mode. 1:fix 2:blink 3:scroll
OBJECT-TYPE    
  INTEGER fix(1), blink(2), scroll(3), blinkScroll(4)  

brLCDString3 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.5.8
LCD Display String of first line.
OBJECT-TYPE    
  OCTET STRING  

brLCDMode4 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.5.9
LCD Display Mode. 1:fix 2:blink 3:scroll
OBJECT-TYPE    
  INTEGER fix(1), blink(2), scroll(3), blinkScroll(4)  

brLCDString4 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.5.10
LCD Display String of first line.
OBJECT-TYPE    
  OCTET STRING  

brLCDMode5 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.5.11
LCD Display Mode. 1:fix 2:blink 3:scroll
OBJECT-TYPE    
  INTEGER fix(1), blink(2), scroll(3), blinkScroll(4)  

brLCDString5 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.5.12
LCD Display String of first line.
OBJECT-TYPE    
  OCTET STRING  

brLCDContrast 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.5.13
This value adjusts the contrast of the LCD Display.
OBJECT-TYPE    
  INTEGER  

printerinfomation 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5
OBJECT IDENTIFIER    

brInfoSerialNumber 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.1
Serial number of printer
OBJECT-TYPE    
  OCTET STRING  

brInfoType 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.2
unused
OBJECT-TYPE    
  INTEGER 0..255  

version 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.3
OBJECT IDENTIFIER    

brInfoUpperMIBVer 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.3.1
unused (upper digit of the MIB version)
OBJECT-TYPE    
  INTEGER 0..255  

brInfoLowerMIBVer 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.3.2
unused (lower digit of the MIB version)
OBJECT-TYPE    
  INTEGER 0..255  

brInfoStatus 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.4
Status message ID
OBJECT-TYPE    
  INTEGER 0..255  

brInfoNetVerUpStatus 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.5
unused
OBJECT-TYPE    
  INTEGER 0..255  

brInfoPrinterUStatus 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.6
Status ID
OBJECT-TYPE    
  INTEGER  

brInfoPConSupported 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.7
BRPCon support 0:not supported 1:supported
OBJECT-TYPE    
  INTEGER  

brInfoMaintenance 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.8
Maintenance info.
OBJECT-TYPE    
  OCTET STRING  

brInfoModelNumber 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.9
Printer Model ID 4:2400Ce 5:3400CN 6:3260 8:2460 9:2600cn 11:3450cn 13:am 14:zlhe 15:zl2 16:jigen 17:aml 18:l4c 19: ALL 20: AL LED 21: AL LCD 22: HL-4040CN 23: ALL China 24: HL-4050CDN/HL-4070CDW 25: ALL2 101:ZL MFC FB type 102:ZL MFC Normal type 103:BH MFC Nornal type 104:BH MFC FB type 105:ZL MFC with HS 106:BH MFC with HS 107: ZL2FB 108: BHL2MFC 109: BHL2FB 110: ZL2MFC 111: Mini2 112: Mini2 ADF 113: BH3FB 114: BH3MFC 115: ALL-MFC 116: ALL-FB 117: SLow4C 118: mini2eColorLCD, 119: mini2eColorLCD ADF 120: AL-FB 121: DCP540 122: DCP750 123: MFC440 124: MFC665 125: MFC850 126: MFC860 127: MFC5460 128: MFC5860 129: DCP6150 130: DCP6260 131: MFC6460 132: MFC6860 133: DCP770 134: MFC480 135: AC-FB CIS 136: AC-FB CCD 137: MFC7440 138: MFC7840 139: MFC5490 140: MFC5890 141: MFC6490 142: DCP6690 143: MFC6890 144: DCP585 145: MFC490 146: MFC790 147: MFC990 148: MFC930
OBJECT-TYPE    
  INTEGER hl2400ce(4), hl3400CN(5), hl3260(6), hl2460(8), hl2600cn(9), hl3450cn(11), am(13), zlhe(14), zl2(15), jigen(16), aml(17), l4c(18), all(19), alLedModel(20), alLcdModel(21), hl4040(22), allchn(23), hl4050hl4070(24), all2(25), zlfb(101), zl(102), bh(103), bhfb(104), zlhs(105), bhhs(106), zl2fb(107), bhl2mfc(108), bhl2fb(109), zl2mfc(110), mini2(111), mini2adf(112), bh3fb(113), bh3mfc(114), allmfc(115), allfb(116), slow4c(117), mini2eColorLCD(118), mini2eColorLCDADF(119), alfb(120), dcp540(121), dcp750(122), mfc440(123), mfc665(124), mfc850(125), mfc860(126), mfc5460(127), mfc5860(128), dcp6150(129), dcp6260(130), dcp6460(131), dcp6860(132), dcp770(133), mfc480(134), acfbCIS(135), acfbCCD(136), mfc7440(137), mfc7840(138), mfc5490(139), mfc5890(140), mfc6490(141), dcp6690(142), mfc6890(143), dcp585(144), mfc490(145), mfc790(146), mfc990(147), mfc930(148)  

brInfoCounter 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.10
Page counter
OBJECT-TYPE    
  OCTET STRING  

brInfoNextCare 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.11
Remaining life info.
OBJECT-TYPE    
  OCTET STRING  

brInfoHDDSlot1 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.12
Card Slot1 status 1:complete 2:IO error 3:memory error 4:not found 5:no device 6:no file(format)
OBJECT-TYPE    
  INTEGER 0..6  

brInfoHDDSlot2 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.13
Card Slot2 status 1:complete 2:IO error 3:memory error 4:not found 5:no device 6:no file(format)
OBJECT-TYPE    
  INTEGER 0..6  

brInfoHDDInternal 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.14
Internal HDD info. 1:complete 2:IO error 3:memory error 4:not found 5:no device 6:no file(format)
OBJECT-TYPE    
  INTEGER 0..6  

brInfoHDDSize 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.15
unused
OBJECT-TYPE    
  OCTET STRING  

brInfoSolutionsCenterURL 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.16
Brother Solutions Center's URL
OBJECT-TYPE    
  DisplayString  

brInfoDeviceRomVersion 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.17
The device rom version
OBJECT-TYPE    
  DisplayString  

brInfoCoverage 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.18
Coverage info.
OBJECT-TYPE    
  OCTET STRING  

brInfoEstimatedPagesRemaining 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.19
Estimated pages remaining info.
OBJECT-TYPE    
  Counter  

brInfoReplaceCount 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.20
Replace count info.
OBJECT-TYPE    
  OCTET STRING  

brInfoJamCount 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.21
Jam count info.
OBJECT-TYPE    
  OCTET STRING  

brInfoJamCountClear 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.22
Jam count Clear.
OBJECT-TYPE    
  INTEGER  

brInfoReplaceTime 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.23
Replace count time info.
OBJECT-TYPE    
  OCTET STRING  

brInfoDeviceSubRomVersion 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.24
The PCL/PS ROM Version.
OBJECT-TYPE    
  OCTET STRING  

brInfoAlertVersion 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.25
It indicates the version that prtAlertLocation is implemented correctly.
OBJECT-TYPE    
  INTEGER  

brInfoBlackPrint 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.26
It indicates black only print enable/disable info 0: disable 1: enable
OBJECT-TYPE    
  INTEGER 0..1  

errorHistory 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.51
OBJECT IDENTIFIER    

brErrorHistoryCount 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.51.1
Maximum number of Error History.
OBJECT-TYPE    
  INTEGER  

brErrorHistoryTable 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.51.2
This table represents Error History.
OBJECT-TYPE    
  SEQUENCE OF  
    BrErrorHistoryEntry

brErrorHistoryEntry 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.51.2.1
A row in the ErrorHistory table. Rows cannot be created or deleted.
OBJECT-TYPE    
  BrErrorHistoryEntry  

brErrorHistoryIndex 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.51.2.1.1
A unique value for the error history.
OBJECT-TYPE    
  INTEGER 1..65535  

brErrorHistoryDescription 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.51.2.1.2
The ErrorHistory Description.
OBJECT-TYPE    
  OCTET STRING  

brErrorHistoryAllClear 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.51.3
All clear Error History.
OBJECT-TYPE    
  INTEGER  

brCommunicationErrorHistoryCount 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.51.11
Maximum number of Communication Error History.
OBJECT-TYPE    
  INTEGER  

brCommunicationErrorHistoryTable 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.51.12
This table represents Communication Error History.
OBJECT-TYPE    
  SEQUENCE OF  
    BrCommunicationErrorHistoryEntry

brCommunicationErrorHistoryEntry 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.51.12.1
A row in the Communication ErrorHistory table. Rows cannot be created or deleted.
OBJECT-TYPE    
  BrCommunicationErrorHistoryEntry  

brCommunicationErrorHistoryIndex 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.51.12.1.1
A unique value for the Communication error history.
OBJECT-TYPE    
  INTEGER 1..65535  

brCommunicationErrorHistoryDescription 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.51.12.1.2
The Communication Error History Description.
OBJECT-TYPE    
  OCTET STRING  

printPages 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.52
OBJECT IDENTIFIER    

brPrintPagesTable 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.52.1
This table represents Print Pages.
OBJECT-TYPE    
  SEQUENCE OF  
    BrPrintPagesEntry

brPrintPagesEntry 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.52.1.1
A row in the PrintPages table. Rows cannot be created or deleted.
OBJECT-TYPE    
  BrPrintPagesEntry  

brPrintPagesIndex 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.52.1.1.1
A unique value for the print pages.
OBJECT-TYPE    
  INTEGER 1..65535  

brPrintPagesPaperSize 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.52.1.1.2
The paper size of print pages.
OBJECT-TYPE    
  INTEGER executive(1), letter(2), legal(3), a6(24), a5(25), a4(26), a3ISO(27), b5JIS(45), b4JIS(46), monarch(80), com10(81), dl(90), c5(91), b6(99), b5(100), ledger(890), a3PLUS(891), letterShortEdge(892), a4ShortEdge(893), a4LONG(894), executiveShortEdge(895), b5ISOShortEdge(896), custom(897), a4Letter(898), b5Executive(899), envelopes(900), dll(901), hagaki(902), folio(903), organaizerJ(904), organaizerK(905), organaizerL(906), organaizerM(907), userdefined(908), legalA4Long(909), b6A5A6(910), detectsensor(911), inches3x5(920), envelopesY4(921), largestEnvelopesTheWest(922), otherPage(999), b6JIS(924)  

brPrintPages 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.52.1.1.3
The count of Print pages.
OBJECT-TYPE    
  Counter  

brPrintPagesMediaPlaceTable 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.52.11
This table represents Print Pages of Media Place.
OBJECT-TYPE    
  SEQUENCE OF  
    BrPrintPagesMediaPlaceEntry

brPrintPagesMediaPlaceEntry 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.52.11.1
A row in the PrintPages Media Place table. Rows cannot be created or deleted.
OBJECT-TYPE    
  BrPrintPagesMediaPlaceEntry  

brPrintPagesMediaPlaceIndex 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.52.11.1.1
A unique value for the print pages of media place.
OBJECT-TYPE    
  INTEGER 1..65535  

brPrintPagesMediaPlaceType 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.52.11.1.2
The place of media.
OBJECT-TYPE    
  INTEGER face(1), back(2)  

brPrintPagesMediaPlaceCounter 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.52.11.1.3
The count of Print pages of media place.
OBJECT-TYPE    
  Counter  

brPrintPagesFuncTable 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.52.21
This table represents Print Pages of each function.
OBJECT-TYPE    
  SEQUENCE OF  
    BrPrintPagesFuncEntry

brPrintPagesFuncEntry 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.52.21.1
A row in the PrintPages Func table. Rows cannot be created or deleted.
OBJECT-TYPE    
  BrPrintPagesFuncEntry  

brPrintPagesFuncIndex 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.52.21.1.1
A unique value for the print pages of each function.
OBJECT-TYPE    
  INTEGER 1..65535  

brPrintPagesFuncType 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.52.21.1.2
The kind of function.
OBJECT-TYPE    
  INTEGER pcPrinttotal(1), faxtotal(2), copytotal(3), copycolor(4), pcPrintcolor(5), faxcolor(6), pcPrintmono(7), faxmono(8), copymono(9)  

brPrintPagesFuncCounter 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.52.21.1.3
The count of Print pages of the function.
OBJECT-TYPE    
  Counter  

brPrintPagesPaperTypeTable 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.52.31
This table represents Print Pages of Paper Type.
OBJECT-TYPE    
  SEQUENCE OF  
    BrPrintPagesPaperTypeEntry

brPrintPagesPaperTypeEntry 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.52.31.1
A row in the PrintPages Paper Type table. Rows cannot be created or deleted.
OBJECT-TYPE    
  BrPrintPagesPaperTypeEntry  

brPrintPagesPaperTypeIndex 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.52.31.1.1
A unique value for the print pages of paper type.
OBJECT-TYPE    
  INTEGER 1..32767  

brPrintPagesPaperTypeType 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.52.31.1.2
The type of paper.
OBJECT-TYPE    
  INTEGER regularthinrecycled(12), transparency(3), thickthickerbond(13), envelopesenvthickenvthin(14)  

brPrintPagesPaperTypeCounter 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.52.31.1.3
The count of Print pages of paper type.
OBJECT-TYPE    
  Counter  

capability 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53
OBJECT IDENTIFIER    

copies 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.1
OBJECT IDENTIFIER    

brCapabilityCopiesMax 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.1.1
The maximum value of copies
OBJECT-TYPE    
  INTEGER  

brCapabilityCopiesMin 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.1.2
The minimum value of copies
OBJECT-TYPE    
  INTEGER  

orientation 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.2
OBJECT IDENTIFIER    

brCapabilityOrientationCount 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.2.1
The number of support of orientation
OBJECT-TYPE    
  INTEGER  

brCapabilityOrientationTable 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.2.2
This table represents capability of orientation.
OBJECT-TYPE    
  SEQUENCE OF  
    BrCapabilityOrientationEntry

brCapabilityOrientationEntry 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.2.2.1
A row in the capability of orientation table. Rows cannot be created or deleted.
OBJECT-TYPE    
  BrCapabilityOrientationEntry  

brCapabilityOrientationIndex 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.2.2.1.1
A unique value for the capability of orientation.
OBJECT-TYPE    
  INTEGER 1..65535  

brCapabilityOrientationName 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.2.2.1.2
The name of orientation currently supported.
OBJECT-TYPE    
  DisplayString  

paper 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.3
OBJECT IDENTIFIER    

brCapabilityPaperCount 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.3.1
The number of kinds of the paper currently supported
OBJECT-TYPE    
  INTEGER  

brCapabilityPaperTable 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.3.2
This table represents capability of paper.
OBJECT-TYPE    
  SEQUENCE OF  
    BrCapabilityPaperEntry

brCapabilityPaperEntry 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.3.2.1
A row in the capability of paper table. Rows cannot be created or deleted.
OBJECT-TYPE    
  BrCapabilityPaperEntry  

brCapabilityPaperIndex 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.3.2.1.1
A unique value for the capability of paper.
OBJECT-TYPE    
  INTEGER 1..65535  

brCapabilityPaperName 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.3.2.1.2
The name of paper currently supported.
OBJECT-TYPE    
  DisplayString  

mediatype 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.4
OBJECT IDENTIFIER    

brCapabilityMediatypeCount 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.4.1
The number of kinds of the mediatype currently supported
OBJECT-TYPE    
  INTEGER  

brCapabilityMediatypeTable 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.4.2
This table represents capability of mediatype.
OBJECT-TYPE    
  SEQUENCE OF  
    BrCapabilityMediatypeEntry

brCapabilityMediatypeEntry 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.4.2.1
A row in the capability of mediatype table. Rows cannot be created or deleted.
OBJECT-TYPE    
  BrCapabilityMediatypeEntry  

brCapabilityMediatypeIndex 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.4.2.1.1
A unique value for the capability of mediatype.
OBJECT-TYPE    
  INTEGER 1..65535  

brCapabilityMediatypeName 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.4.2.1.2
The name of mediatype currently supported.
OBJECT-TYPE    
  DisplayString  

resolution 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.5
OBJECT IDENTIFIER    

brCapabilityResolutionCount 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.5.1
The number of kinds of the resolution currently supported
OBJECT-TYPE    
  INTEGER  

brCapabilityResolutionTable 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.5.2
This table represents capability of resolution.
OBJECT-TYPE    
  SEQUENCE OF  
    BrCapabilityResolutionEntry

brCapabilityResolutionEntry 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.5.2.1
A row in the capability of resolution table. Rows cannot be created or deleted.
OBJECT-TYPE    
  BrCapabilityResolutionEntry  

brCapabilityResolutionIndex 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.5.2.1.1
A unique value for the capability of resolution.
OBJECT-TYPE    
  INTEGER 1..65535  

brCapabilityResolution 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.5.2.1.2
The value of resolution currently supported.
OBJECT-TYPE    
  INTEGER  

countinfo 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.54
OBJECT IDENTIFIER    

pfkit 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.54.1
OBJECT IDENTIFIER    

brPfKitIndexCount 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.54.1.1
Maximum number of PF kit.
OBJECT-TYPE    
  INTEGER  

brPfKitTable 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.54.1.2
This table represents PF kit.
OBJECT-TYPE    
  SEQUENCE OF  
    BrPfKitEntry

brPfKitEntry 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.54.1.2.1
A row in the PfKit table. Rows cannot be created or deleted.
OBJECT-TYPE    
  BrPfKitEntry  

brPfKitIndex 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.54.1.2.1.1
A unique value for the PF kit.
OBJECT-TYPE    
  INTEGER 1..65535  

brPfKitType 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.54.1.2.1.2
The PF kit ID.
OBJECT-TYPE    
  INTEGER pfkit1(1), pfkit2(2), pfkit3(3), pfkit4(4), pfkitmp(10), pfkitdx(20)  

brPfKitCount 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.54.1.2.1.3
Counter of the PF kit.
OBJECT-TYPE    
  Counter  

scancount 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.54.2
OBJECT IDENTIFIER    

brScanCountIndexCount 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.54.2.1
Maximum number of Scan place.
OBJECT-TYPE    
  INTEGER  

brScanCountTable 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.54.2.2
This table represents scan count.
OBJECT-TYPE    
  SEQUENCE OF  
    BrScanCountEntry

brScanCountEntry 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.54.2.2.1
A row in the ScanCount table. Rows cannot be created or deleted.
OBJECT-TYPE    
  BrScanCountEntry  

brScanCountIndex 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.54.2.2.1.1
A unique value for the scan count place.
OBJECT-TYPE    
  INTEGER 1..65535  

brScanCountType 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.54.2.2.1.2
The scan place ID.
OBJECT-TYPE    
  INTEGER adf(1), fb(2), adfdx(3)  

brScanCountCounter 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.54.2.2.1.3
Counter of the scan.
OBJECT-TYPE    
  Counter  

firmwareupdatekeyword 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.55
OBJECT IDENTIFIER    

brFirmwareUpdateKeywordCount 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.55.1
The number of Firmware for update the device.
OBJECT-TYPE    
  INTEGER 1..4  

brFirmwareUpdateKeywordTable 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.55.2
The table represents the number of Firmware for Update.
OBJECT-TYPE    
  SEQUENCE OF  
    BrFirmwareUpdateKeywordEntry

brFirmwareUpdateKeywordEntry 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.55.2.1
A row in the FirmwareUpdateKeyword table. Rows cannot be created or deleted.
OBJECT-TYPE    
  BrFirmwareUpdateKeywordEntry  

brFirmwareUpdateKeywordIndex 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.55.2.1.1
OBJECT-TYPE    
  INTEGER 0..4  

brFirmwareUpdateKeyword 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.55.2.1.2
The keyword for firemware update the device.
OBJECT-TYPE    
  OCTET STRING SIZE(0..255)  

printerstatus 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.6
OBJECT IDENTIFIER    

brStatusSleep 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.6.1
Sleeping status 0:ready 1:sleep
OBJECT-TYPE    
  INTEGER 0..2  

secret 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.7
OBJECT IDENTIFIER    

brSecretMPRetry 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.7.1
unused
OBJECT-TYPE    
  INTEGER 0..255  

brSecretReprint 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.7.2
Secret Reprint mode 0:Off 111:On 222:Job
OBJECT-TYPE    
  INTEGER  

brFontSetting 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.7.3
Font Setting 0:Brother Font 1:Agfa Font
OBJECT-TYPE    
  INTEGER 0..1  

brFontSwitchOn 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.7.4
Switch of Agfa Font On
OBJECT-TYPE    
  INTEGER 0..999999  

brFontSwitchOff 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.7.5
Switch of Agfa Font Off
OBJECT-TYPE    
  INTEGER 0..999999  

adminsetting 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.8
OBJECT IDENTIFIER    

clockfunction 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.8.1
OBJECT IDENTIFIER    

brClockFuncTimeStyle 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.8.1.1
Time format 0:YMD 1:MDY 2:DMY
OBJECT-TYPE    
  INTEGER 0..2  

brClockFuncSummerTime 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.8.1.2
Summer time 1:Off 2:On
OBJECT-TYPE    
  INTEGER 0..2  

brClockFuncTimeZone 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.8.1.3
TimeZone
OBJECT-TYPE    
  INTEGER -24..24  

brClockFuncZoneSet 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.8.1.4
TimeZone enable 1:Off 2:On
OBJECT-TYPE    
  INTEGER 0..2  

interface 1.3.6.1.4.1.2435.2.4
OBJECT IDENTIFIER    

npCard 1.3.6.1.4.1.2435.2.4.3
OBJECT IDENTIFIER    

npSys 1.3.6.1.4.1.2435.2.4.3.1
OBJECT IDENTIFIER    

npConfig 1.3.6.1.4.1.2435.2.4.3.1.1
OBJECT IDENTIFIER    

brBasicSettingConfigured 1.3.6.1.4.1.2435.2.4.3.1.1.1
This value indicates that the basic setting is configured or not. The condition entry of this value is model dependent.
OBJECT-TYPE    
  INTEGER unconfigured(1), configured(2)  

adminCapa 1.3.6.1.4.1.2435.2.4.3.1.99
OBJECT IDENTIFIER    

brAdminCapability 1.3.6.1.4.1.2435.2.4.3.1.99.1
AdminCapability
OBJECT-TYPE    
  OCTET STRING  

userSetting 1.3.6.1.4.1.2435.2.4.3.1.100
OBJECT IDENTIFIER    

brUserPasswordVerify 1.3.6.1.4.1.2435.2.4.3.1.100.1
Submit the print server's user password for verification. An error will be returned if the password is incorrect.
OBJECT-TYPE    
  DisplayString  

brUserPassword 1.3.6.1.4.1.2435.2.4.3.1.100.2
Set the print server's user password value.
OBJECT-TYPE    
  DisplayString  

verify 1.3.6.1.4.1.2435.2.4.3.1.101
OBJECT IDENTIFIER    

brpsVerifyPhysAddress 1.3.6.1.4.1.2435.2.4.3.1.101.1
For verify physical address.
OBJECT-TYPE    
  OCTET STRING SIZE(0..6)  

npTcp 1.3.6.1.4.1.2435.2.4.3.6
OBJECT IDENTIFIER    

lpd 1.3.6.1.4.1.2435.2.4.3.6.99
OBJECT IDENTIFIER    


brLPDBannerPage 1.3.6.1.4.1.2435.2.4.3.6.99.1.1
LPR banner page 0: disabled. 1: enabled. 2: force to print.
OBJECT-TYPE    
  INTEGER 0..2  

npCtl 1.3.6.1.4.1.2435.2.4.3.7
OBJECT IDENTIFIER    

etherN 1.3.6.1.4.1.2435.2.4.3.7.99
OBJECT IDENTIFIER    

eNet 1.3.6.1.4.1.2435.2.4.3.7.99.1
OBJECT IDENTIFIER    

brENetModeSupported 1.3.6.1.4.1.2435.2.4.3.7.99.1.1
ENet Mode 0:not supported 1:supported
OBJECT-TYPE    
  INTEGER 0..1  

brENetMode 1.3.6.1.4.1.2435.2.4.3.7.99.1.2
ENet Mode 0:Auto 1:FD100B 2:100Base 3:FD10B 4:10BASE
OBJECT-TYPE    
  INTEGER 0..255  

npPort 1.3.6.1.4.1.2435.2.4.3.13
OBJECT IDENTIFIER    

funa 1.3.6.1.4.1.2435.2.4.3.13.10
OBJECT IDENTIFIER    

brFindPort 1.3.6.1.4.1.2435.2.4.3.13.10.1
OBJECT-TYPE    
  INTEGER 0..65535  

brFindTime 1.3.6.1.4.1.2435.2.4.3.13.10.2
OBJECT-TYPE    
  INTEGER 0..255  

npSet 1.3.6.1.4.1.2435.2.4.3.99
OBJECT IDENTIFIER    

dns 1.3.6.1.4.1.2435.2.4.3.99.1
OBJECT IDENTIFIER    

brDNSSupported 1.3.6.1.4.1.2435.2.4.3.99.1.1
DNS resolver 0:not supported 1:supported This is the obsolete MIB that is not currently used.
OBJECT-TYPE    
  INTEGER 0..1  

brPrimaryDNSIP 1.3.6.1.4.1.2435.2.4.3.99.1.2
Primary DNS IP Address. This is the obsolete MIB that is not currently used.
OBJECT-TYPE    
  OCTET STRING  

brSecondaryDNSIP 1.3.6.1.4.1.2435.2.4.3.99.1.3
Secondary DNS IP Address This is the obsolete MIB that is not currently used.
OBJECT-TYPE    
  OCTET STRING  

brDNSIPSetup 1.3.6.1.4.1.2435.2.4.3.99.1.4
DNS mode 1:static 2:auto
OBJECT-TYPE    
  INTEGER static(1), auto(2)  

brTCPIPConnectTime 1.3.6.1.4.1.2435.2.4.3.99.1.5
TCP/IP connect time.
OBJECT-TYPE    
  INTEGER  

brAdvancedDNSSupported 1.3.6.1.4.1.2435.2.4.3.99.1.6
DNS resolver 0:not supported 1:supported
OBJECT-TYPE    
  INTEGER 0..1  

brPrimaryDNSIPAddress 1.3.6.1.4.1.2435.2.4.3.99.1.7
Primary DNS IP Address
OBJECT-TYPE    
  IpAddress  

brSecondaryDNSIPAddress 1.3.6.1.4.1.2435.2.4.3.99.1.8
Secondary DNS IP Address
OBJECT-TYPE    
  IpAddress  

brPOP3ServerName 1.3.6.1.4.1.2435.2.4.3.99.1.9
The FQDN name of the POP3 server.
OBJECT-TYPE    
  OCTET STRING SIZE(0..64)  

brSMTPServerName 1.3.6.1.4.1.2435.2.4.3.99.1.10
The FQDN name of the SMTP server.
OBJECT-TYPE    
  OCTET STRING SIZE(0..64)  

pushstatus 1.3.6.1.4.1.2435.2.4.3.99.2
OBJECT IDENTIFIER    

brPushStatusSupported 1.3.6.1.4.1.2435.2.4.3.99.2.1
Notification 0:not supported 1:supported
OBJECT-TYPE    
  INTEGER 0..1  

priadmin 1.3.6.1.4.1.2435.2.4.3.99.2.2
OBJECT IDENTIFIER    

brPriMailAddress 1.3.6.1.4.1.2435.2.4.3.99.2.2.1
Primary Mail Address
OBJECT-TYPE    
  OCTET STRING  

brPriError 1.3.6.1.4.1.2435.2.4.3.99.2.2.2
Primary Error
OBJECT-TYPE    
  INTEGER 0..65535  

secadmin 1.3.6.1.4.1.2435.2.4.3.99.2.3
OBJECT IDENTIFIER    

brSecMailAddress 1.3.6.1.4.1.2435.2.4.3.99.2.3.1
Secondary Mail Address
OBJECT-TYPE    
  OCTET STRING  

brSecError 1.3.6.1.4.1.2435.2.4.3.99.2.3.2
Secondary Error
OBJECT-TYPE    
  INTEGER 0..65535  

brNotificationCount 1.3.6.1.4.1.2435.2.4.3.99.2.4
Maximum number of Notification Method.
OBJECT-TYPE    
  INTEGER 1..127  

brNotificationTable 1.3.6.1.4.1.2435.2.4.3.99.2.5
This table represents Notification Method.
OBJECT-TYPE    
  SEQUENCE OF  
    BrNotificationEntry

brNotificationEntry 1.3.6.1.4.1.2435.2.4.3.99.2.5.1
A row in the Notification table. Rows cannot be created or deleted.
OBJECT-TYPE    
  BrNotificationEntry  

brNotificationIndex 1.3.6.1.4.1.2435.2.4.3.99.2.5.1.1
The number.
OBJECT-TYPE    
  INTEGER 1..65535  

brNotificationAddress 1.3.6.1.4.1.2435.2.4.3.99.2.5.1.2
The Notification Address.
OBJECT-TYPE    
  OCTET STRING  

brNotificationStatusGroup 1.3.6.1.4.1.2435.2.4.3.99.2.5.1.3
The Notification Status group
OBJECT-TYPE    
  INTEGER  

brNotificationShowURLInfo 1.3.6.1.4.1.2435.2.4.3.99.2.5.1.4
The setting of show URL infomation at Notification mail.
OBJECT-TYPE    
  INTEGER  

brNotificationErrorRule 1.3.6.1.4.1.2435.2.4.3.99.2.5.1.5
The setting of sending requirements for Notification.
OBJECT-TYPE    
  OCTET STRING  

brNotificationRestoration 1.3.6.1.4.1.2435.2.4.3.99.2.5.1.6
The setting of Restoration Notification mail
OBJECT-TYPE    
  INTEGER off(1), on(2)  

brPrintersEmailaddress 1.3.6.1.4.1.2435.2.4.3.99.2.6
The Printers Email Address.
OBJECT-TYPE    
  OCTET STRING  

brNotificationVersion 1.3.6.1.4.1.2435.2.4.3.99.2.7
The version of Notification
OBJECT-TYPE    
  OCTET STRING  

brShowIPAddressInfo 1.3.6.1.4.1.2435.2.4.3.99.2.8
The setting of show IP address infomation at Notification mail.
OBJECT-TYPE    
  INTEGER off(1), on(2)  

brNotificationRuleTable 1.3.6.1.4.1.2435.2.4.3.99.2.50
This table represents Notification Method.
OBJECT-TYPE    
  SEQUENCE OF  
    BrNotificationRuleEntry

brNotificationRuleEntry 1.3.6.1.4.1.2435.2.4.3.99.2.50.1
A row in the Notification rule table. Rows cannot be created or deleted.
OBJECT-TYPE    
  BrNotificationRuleEntry  

brNotificationRuleIndex 1.3.6.1.4.1.2435.2.4.3.99.2.50.1.1
The number.
OBJECT-TYPE    
  INTEGER 1..65535  

brNotificationStatusID 1.3.6.1.4.1.2435.2.4.3.99.2.50.1.2
The Notification Status group ID
OBJECT-TYPE    
  INTEGER coverOpen(1), jam(2), tonerLow(3), tonerEmpty(4), userConsumableWarning(5), userConsumableError(6), servicemanConsumableWarning(7), servicemanConsumableError(8), changeDrum(9), memoryFull(10), inputMediaError(11), outputFull(12), notInstalled(13), machineError(14), otherErrors(15)  

brNotificationMainRule 1.3.6.1.4.1.2435.2.4.3.99.2.50.1.3
The main rule of Notification setting.
OBJECT-TYPE    
  INTEGER off(1), everytime(2), times(3), minutes(4)  

brNotificationRuleValue 1.3.6.1.4.1.2435.2.4.3.99.2.50.1.4
The value of Notification setting.
OBJECT-TYPE    
  INTEGER  

pjl 1.3.6.1.4.1.2435.2.4.3.99.3
OBJECT IDENTIFIER    

pjlinfo 1.3.6.1.4.1.2435.2.4.3.99.3.1
OBJECT IDENTIFIER    

brPJLInfoOptionsTable 1.3.6.1.4.1.2435.2.4.3.99.3.1.1
This table represents PJLInfoOptions.
OBJECT-TYPE    
  SEQUENCE OF  
    BrPJLInfoOptionsEntry

brPJLInfoOptionsEntry 1.3.6.1.4.1.2435.2.4.3.99.3.1.1.1
A row in the PJLInfoOptions table. Rows cannot be created or deleted.
OBJECT-TYPE    
  BrPJLInfoOptionsEntry  

brPJLInfoOptionsIndex 1.3.6.1.4.1.2435.2.4.3.99.3.1.1.1.1
The number.
OBJECT-TYPE    
  INTEGER 1..65535  

brPJLInfoOptions 1.3.6.1.4.1.2435.2.4.3.99.3.1.1.1.2
The PJLInfoOptions.
OBJECT-TYPE    
  OCTET STRING SIZE(0..32)  

brPJLInfoIntrayconfigTable 1.3.6.1.4.1.2435.2.4.3.99.3.1.2
This table represents PJLInfoIntrayconfig.
OBJECT-TYPE    
  SEQUENCE OF  
    BrPJLInfoIntrayconfigEntry

brPJLInfoIntrayconfigEntry 1.3.6.1.4.1.2435.2.4.3.99.3.1.2.1
A row in the PJLInfoIntrayconfig table. Rows cannot be created or deleted.
OBJECT-TYPE    
  BrPJLInfoIntrayconfigEntry  

brPJLInfoIntrayconfigIndex 1.3.6.1.4.1.2435.2.4.3.99.3.1.2.1.1
The number.
OBJECT-TYPE    
  INTEGER 1..65535  

brPJLInfoIntrayconfig 1.3.6.1.4.1.2435.2.4.3.99.3.1.2.1.2
The PJLInfoIntrayconfig.
OBJECT-TYPE    
  OCTET STRING SIZE(0..32)  

brPJLInfoOuttrayconfigTable 1.3.6.1.4.1.2435.2.4.3.99.3.1.3
This table represents PJLInfoOuttrayconfig.
OBJECT-TYPE    
  SEQUENCE OF  
    BrPJLInfoOuttrayconfigEntry

brPJLInfoOuttrayconfigEntry 1.3.6.1.4.1.2435.2.4.3.99.3.1.3.1
A row in the PJLInfoOuttrayconfig table. Rows cannot be created or deleted.
OBJECT-TYPE    
  BrPJLInfoOuttrayconfigEntry  

brPJLInfoOuttrayconfigIndex 1.3.6.1.4.1.2435.2.4.3.99.3.1.3.1.1
The number.
OBJECT-TYPE    
  INTEGER 1..65535  

brPJLInfoOuttrayconfig 1.3.6.1.4.1.2435.2.4.3.99.3.1.3.1.2
The PJLInfoOuttrayconfig.
OBJECT-TYPE    
  OCTET STRING SIZE(0..32)  

brPJLInfoDXconfigTable 1.3.6.1.4.1.2435.2.4.3.99.3.1.4
This table represents PJLInfoDXconfig.
OBJECT-TYPE    
  SEQUENCE OF  
    BrPJLInfoDXconfigEntry

brPJLInfoDXconfigEntry 1.3.6.1.4.1.2435.2.4.3.99.3.1.4.1
A row in the PJLInfoDXconfig table. Rows cannot be created or deleted.
OBJECT-TYPE    
  BrPJLInfoDXconfigEntry  

brPJLInfoDXconfigIndex 1.3.6.1.4.1.2435.2.4.3.99.3.1.4.1.1
The number.
OBJECT-TYPE    
  INTEGER 1..65535  

brPJLInfoDXconfig 1.3.6.1.4.1.2435.2.4.3.99.3.1.4.1.2
The PJLInfoDXconfig.
OBJECT-TYPE    
  OCTET STRING SIZE(0..32)  

brPJLInfoStorageconfigTable 1.3.6.1.4.1.2435.2.4.3.99.3.1.5
This table represents PJLInfoStorageconfig.
OBJECT-TYPE    
  SEQUENCE OF  
    BrPJLInfoStorageconfigEntry

brPJLInfoStorageconfigEntry 1.3.6.1.4.1.2435.2.4.3.99.3.1.5.1
A row in the PJLInfoStorageconfig table. Rows cannot be created or deleted.
OBJECT-TYPE    
  BrPJLInfoStorageconfigEntry  

brPJLInfoStorageconfigIndex 1.3.6.1.4.1.2435.2.4.3.99.3.1.5.1.1
The number.
OBJECT-TYPE    
  INTEGER 1..65535  

brPJLInfoStorageconfig 1.3.6.1.4.1.2435.2.4.3.99.3.1.5.1.2
The PJLInfoStorageconfig.
OBJECT-TYPE    
  OCTET STRING SIZE(0..32)  

brPJLInfoFirmwareUpdateconfigTable 1.3.6.1.4.1.2435.2.4.3.99.3.1.6
This table represents PJLInfoFirmwareUpdateconfig.
OBJECT-TYPE    
  SEQUENCE OF  
    BrPJLInfoFirmwareUpdateconfigEntry

brPJLInfoFirmwareUpdateconfigEntry 1.3.6.1.4.1.2435.2.4.3.99.3.1.6.1
A row in the PJLInfoFirmwareUpdateconfig table. Rows cannot be created or deleted.
OBJECT-TYPE    
  BrPJLInfoFirmwareUpdateconfigEntry  

brPJLInfoFirmwareUpdateconfigIndex 1.3.6.1.4.1.2435.2.4.3.99.3.1.6.1.1
The number.
OBJECT-TYPE    
  INTEGER 1..65535  

brPJLInfoFirmwareUpdateconfig 1.3.6.1.4.1.2435.2.4.3.99.3.1.6.1.2
The PJLInfoFirmwareUpdateconfig.
OBJECT-TYPE    
  OCTET STRING SIZE(0..255)  

eMailReports 1.3.6.1.4.1.2435.2.4.3.99.4
OBJECT IDENTIFIER    

brEmailReportsSupported 1.3.6.1.4.1.2435.2.4.3.99.4.1
E-mail reports 0:not supported 1:supported
OBJECT-TYPE    
  INTEGER 0..1  

brEmailReportsCount 1.3.6.1.4.1.2435.2.4.3.99.4.2
The number of Administrator for E-mail reports.
OBJECT-TYPE    
  INTEGER  

brEmailReportsTable 1.3.6.1.4.1.2435.2.4.3.99.4.11
This table represents E-mail reports.
OBJECT-TYPE    
  SEQUENCE OF  
    BrEmailReportsEntry

brEmailReportsEntry 1.3.6.1.4.1.2435.2.4.3.99.4.11.1
A row in the BrEmailReportsEntry table. Rows cannot be created or deleted.
OBJECT-TYPE    
  BrEmailReportsEntry  

brEmailReportsIndex 1.3.6.1.4.1.2435.2.4.3.99.4.11.1.1
The number.
OBJECT-TYPE    
  INTEGER 1..16  

brEmailReportsAddress 1.3.6.1.4.1.2435.2.4.3.99.4.11.1.2
The E-mail address of Administrator for E-mail reports.
OBJECT-TYPE    
  OCTET STRING SIZE(0..60)  

brEmailReportsFrequency 1.3.6.1.4.1.2435.2.4.3.99.4.11.1.3
The frequency of sending E-mail reports.
OBJECT-TYPE    
  INTEGER daily(1), weekly(2), monthly(3)  

brEmailReportsTime 1.3.6.1.4.1.2435.2.4.3.99.4.11.1.4
The time setting for E-mail reports.
OBJECT-TYPE    
  OCTET STRING  

brEmailReportsWeek 1.3.6.1.4.1.2435.2.4.3.99.4.11.1.5
The setting of day of the week for E-mail reports.
OBJECT-TYPE    
  INTEGER sunday(1), monday(2), tuesday(3), wednesday(4), thursday(5), friday(6), saturday(7)  

brEmailReportsDate 1.3.6.1.4.1.2435.2.4.3.99.4.11.1.6
The setting of day for E-mail reports when real time clock exists.
OBJECT-TYPE    
  INTEGER 1..31  

brEmailReportsSendReportNow 1.3.6.1.4.1.2435.2.4.3.99.4.11.1.7
The setting of Send Report Now function for E-mail reports.
OBJECT-TYPE    
  INTEGER off(1), on(2)  

brEmailReportsSendReportatPowerOn 1.3.6.1.4.1.2435.2.4.3.99.4.11.1.8
The setting of Send Report at PowerOn for E-mail reports.
OBJECT-TYPE    
  INTEGER off(1), on(2)  

brEmailReportsNoRTCFrequency 1.3.6.1.4.1.2435.2.4.3.99.4.11.1.9
The setting of day for E-mail reports when real time clock does not exists.
OBJECT-TYPE    
  INTEGER 1..30  

brEmailReportsReportFormat 1.3.6.1.4.1.2435.2.4.3.99.4.11.1.10
The setting of ReportFormat for E-mail reports.
OBJECT-TYPE    
  INTEGER plaintext(1), xml(2)  

wireless 1.3.6.1.4.1.2435.2.4.3.100
OBJECT IDENTIFIER    

wlInfo 1.3.6.1.4.1.2435.2.4.3.100.1
OBJECT IDENTIFIER    

wlCapability 1.3.6.1.4.1.2435.2.4.3.100.1.1
OBJECT IDENTIFIER    

brpsWLanDot11Supported 1.3.6.1.4.1.2435.2.4.3.100.1.1.1
Flags per bit. 802.11a bit1=1 802.11b bit2=1 802.11g bit3=1
OBJECT-TYPE    
  INTEGER  

brpsWLanAvailableChannel 1.3.6.1.4.1.2435.2.4.3.100.1.1.2
The available channel list.
OBJECT-TYPE    
  OCTET STRING  

brpsWLanCapabilityEncryptModeCount 1.3.6.1.4.1.2435.2.4.3.100.1.1.3
index
OBJECT-TYPE    
  INTEGER  

brpsWLanCapabilityEncryptModeTable 1.3.6.1.4.1.2435.2.4.3.100.1.1.4
OBJECT-TYPE    
  SEQUENCE OF  
    BrpsWLanCapabilityEncryptModeEntry

brpsWLanCapabilityEncryptModeEntry 1.3.6.1.4.1.2435.2.4.3.100.1.1.4.1
OBJECT-TYPE    
  BrpsWLanCapabilityEncryptModeEntry  

brpsWLanCapabilityEncryptModeIndex 1.3.6.1.4.1.2435.2.4.3.100.1.1.4.1.1
index
OBJECT-TYPE    
  INTEGER 1..255  

brpsWLanCapabilityEncryptModeType 1.3.6.1.4.1.2435.2.4.3.100.1.1.4.1.2
Encrypt Mode Type
OBJECT-TYPE    
  INTEGER none(1), wep(2), tkip(3), aes(4), ckip(5)  

brpsWLanCapabilityEncryptModeDescription 1.3.6.1.4.1.2435.2.4.3.100.1.1.4.1.3
Encrypt Mode description
OBJECT-TYPE    
  OCTET STRING  

brpsWLanCapabilityEncryptModeSupported 1.3.6.1.4.1.2435.2.4.3.100.1.1.4.1.4
0: Not Supported 1: Supported
OBJECT-TYPE    
  INTEGER  

brpsWLanCapabilityAuthModeCount 1.3.6.1.4.1.2435.2.4.3.100.1.1.5
index
OBJECT-TYPE    
  INTEGER  

brpsWLanCapabilityAuthModeTable 1.3.6.1.4.1.2435.2.4.3.100.1.1.6
OBJECT-TYPE    
  SEQUENCE OF  
    BrpsWLanCapabilityAuthModeEntry

brpsWLanCapabilityAuthModeEntry 1.3.6.1.4.1.2435.2.4.3.100.1.1.6.1
OBJECT-TYPE    
  BrpsWLanCapabilityAuthModeEntry  

brpsWLanCapabilitAuthModeIndex 1.3.6.1.4.1.2435.2.4.3.100.1.1.6.1.1
index
OBJECT-TYPE    
  INTEGER 1..255  

brpsWLanCapabilityAuthModeType 1.3.6.1.4.1.2435.2.4.3.100.1.1.6.1.2
Auth Mode Type
OBJECT-TYPE    
  INTEGER opensystem(1), shardkey(2), wpa-psk(3), wpa-none(4), wpa(5), wpa2(6), leap(7), eapfast-none(8), eapfast-mschapv2(9), eapfast-gtc(10), eapfast-tls(11), wpa2-psk(12)  

brpsWLanCapabilityAuthModeDescription 1.3.6.1.4.1.2435.2.4.3.100.1.1.6.1.3
Auth Mode description
OBJECT-TYPE    
  OCTET STRING  

brpsWLanCapabilityAuthModeSupported 1.3.6.1.4.1.2435.2.4.3.100.1.1.6.1.4
0: Not Supported 1: Supported
OBJECT-TYPE    
  INTEGER  

brpsWLanCapabilityAuthEAPCount 1.3.6.1.4.1.2435.2.4.3.100.1.1.7
index
OBJECT-TYPE    
  INTEGER  

brpsWLanCapabilityAuthEAPTable 1.3.6.1.4.1.2435.2.4.3.100.1.1.8
OBJECT-TYPE    
  SEQUENCE OF  
    BrpsWLanCapabilityAuthEAPEntry

brpsWLanCapabilityAuthEAPEntry 1.3.6.1.4.1.2435.2.4.3.100.1.1.8.1
OBJECT-TYPE    
  BrpsWLanCapabilityAuthEAPEntry  

brpsWLanCapabilityAuthEAPIndex 1.3.6.1.4.1.2435.2.4.3.100.1.1.8.1.1
index
OBJECT-TYPE    
  INTEGER 1..65535  

brpsWLanCapabilityAuthEAPType 1.3.6.1.4.1.2435.2.4.3.100.1.1.8.1.2
Auth EAP Type
OBJECT-TYPE    
  INTEGER eap-md5(1), eap-tls(2), eap-ttls(3), peap(4), leap(5), eapfast-none(6), eapfast-mschapv2(7), eapfast-gtc(8), eapfast-tls(9)  

brpsWLanCapabilityAuthEAPDescription 1.3.6.1.4.1.2435.2.4.3.100.1.1.8.1.3
Auth EAP description
OBJECT-TYPE    
  OCTET STRING  

brpsWLanCapabilityAuthEAPSupported 1.3.6.1.4.1.2435.2.4.3.100.1.1.8.1.4
0: Not Supported 1: Supported
OBJECT-TYPE    
  INTEGER  

brpsWLanCapabilityAuthEAPSupportAuthentication 1.3.6.1.4.1.2435.2.4.3.100.1.1.8.1.5
put supported authentication protocol as bit. 1bit:802.1X 2bit:WPA 3bit:WPA2 4bit:CCKM
OBJECT-TYPE    
  INTEGER 0..15  

brpsWLanCapabilityAuthEAPSupportEncryption 1.3.6.1.4.1.2435.2.4.3.100.1.1.8.1.6
put supported encryption as bit. 1bit:WEP 2bit:CKIP 3bit:TKIP 4bit:AES
OBJECT-TYPE    
  INTEGER 0..15  

wlGeneralInfo 1.3.6.1.4.1.2435.2.4.3.100.1.2
OBJECT IDENTIFIER    

brpsWLanDestination 1.3.6.1.4.1.2435.2.4.3.100.1.2.1
The destination of this NIC.
OBJECT-TYPE    
  INTEGER  

brpsWLanTransmitLevel 1.3.6.1.4.1.2435.2.4.3.100.1.2.2
The level of the transmitting power.
OBJECT-TYPE    
  INTEGER  

brpsPit3WLanTestStatus 1.3.6.1.4.1.2435.2.4.3.100.1.2.3
The test status of pit3 for WLAN.
OBJECT-TYPE    
  INTEGER  

wlNetSearch 1.3.6.1.4.1.2435.2.4.3.100.1.11
OBJECT IDENTIFIER    

brpsWLanNetSearchSupported 1.3.6.1.4.1.2435.2.4.3.100.1.11.1
0 indicates the Wireless network serch function is not supported. 1 indicates the Wireless network serch function is implemented by the firmware
OBJECT-TYPE    
  INTEGER  

brpsAvailableWLanScan 1.3.6.1.4.1.2435.2.4.3.100.1.11.2
Read: unsupported(1), supported(2) Set: = <1:Start | 2:Start w/ option>[;;[;]]
OBJECT-TYPE    
  OCTET STRING  

brpsAvailableWLanScanWaitTime 1.3.6.1.4.1.2435.2.4.3.100.1.11.3
Scan Wait Time
OBJECT-TYPE    
  INTEGER  

brpsAvailableWLanCount 1.3.6.1.4.1.2435.2.4.3.100.1.11.10
Available wireless LAN count.
OBJECT-TYPE    
  INTEGER  

brpsAvailableWLanTable 1.3.6.1.4.1.2435.2.4.3.100.1.11.11
This table represents Available Wireless LAN Info.
OBJECT-TYPE    
  SEQUENCE OF  
    BrpsAvailableWLanEntry

brpsAvailableWLanEntry 1.3.6.1.4.1.2435.2.4.3.100.1.11.11.1
A row in the brpsAvailableWLanTable table. Rows cannot be created or deleted.
OBJECT-TYPE    
  BrpsAvailableWLanEntry  

brpsAvailableWLanIndex 1.3.6.1.4.1.2435.2.4.3.100.1.11.11.1.1
The number.
OBJECT-TYPE    
  INTEGER 1..255  

brpsAvailableWLanName 1.3.6.1.4.1.2435.2.4.3.100.1.11.11.1.2
The available wireless LAN name.
OBJECT-TYPE    
  OCTET STRING SIZE(0..32)  

brpsAvailableWLanMode 1.3.6.1.4.1.2435.2.4.3.100.1.11.11.1.3
The available wireless LAN mode.
OBJECT-TYPE    
  INTEGER dot11b-gAuto(1), dot11b(2), dot11g(3)  

brpsAvailableWLanCommMode 1.3.6.1.4.1.2435.2.4.3.100.1.11.11.1.4
The available wireless LAN communication mode.
OBJECT-TYPE    
  INTEGER accesPoint(1), adhoc-Wi-Fi(2)  

brpsAvailableWLanChannel 1.3.6.1.4.1.2435.2.4.3.100.1.11.11.1.5
The available wireless LAN channel.
OBJECT-TYPE    
  INTEGER  

brpsAvailableWLanPowerLevel 1.3.6.1.4.1.2435.2.4.3.100.1.11.11.1.6
The available wireless LAN power level.
OBJECT-TYPE    
  INTEGER  

brpsAvailableWLanAuthMode 1.3.6.1.4.1.2435.2.4.3.100.1.11.11.1.7
The available wireless LAN authentication mode.
OBJECT-TYPE    
  INTEGER none(1), active(2)  

brpsAvailableWLanEncryptMode 1.3.6.1.4.1.2435.2.4.3.100.1.11.11.1.8
The available wireless LAN encryption mode.
OBJECT-TYPE    
  INTEGER none(1), active(2), wep(3), tkip(4)  

wlAOSS 1.3.6.1.4.1.2435.2.4.3.100.1.12
OBJECT IDENTIFIER    

brpsWLanAOSSSupported 1.3.6.1.4.1.2435.2.4.3.100.1.12.1
0 indicates AOSS is not supported. 1 indicates AOSS is supported.
OBJECT-TYPE    
  INTEGER 0..1  

brpsWLanAOSSIsRunnning 1.3.6.1.4.1.2435.2.4.3.100.1.12.2
OBJECT-TYPE    
  INTEGER 0..1  

wlSES 1.3.6.1.4.1.2435.2.4.3.100.1.13
OBJECT IDENTIFIER    

brpsWLanSESSupported 1.3.6.1.4.1.2435.2.4.3.100.1.13.1
0 indicates SES is not supported. 1 indicates SES is supported.
OBJECT-TYPE    
  INTEGER 0..1  

wlWPS 1.3.6.1.4.1.2435.2.4.3.100.1.14
OBJECT IDENTIFIER    

brpsWLanWPSSupported 1.3.6.1.4.1.2435.2.4.3.100.1.14.1
0 indicates WPS is not supported. 1 indicates WPS is supported.
OBJECT-TYPE    
  INTEGER 0..1  

brpsWLanWPSResult 1.3.6.1.4.1.2435.2.4.3.100.1.14.2
0 indicates WPS is successful. 1 indicates WPS is not successful. -1 indicates WPS is being set up.
OBJECT-TYPE    
  INTEGER -1..1  

wlSimpleWizard 1.3.6.1.4.1.2435.2.4.3.100.1.15
OBJECT IDENTIFIER    

brWlanSimpleWizardSupported 1.3.6.1.4.1.2435.2.4.3.100.1.15.1
WLAN Simple Wizard support information. 0 indicates Simple Wizard is not supported. 1 indicates Simple Wizard is supported.
OBJECT-TYPE    
  INTEGER 0..1  

brWlanSimpleWizardPassword 1.3.6.1.4.1.2435.2.4.3.100.1.15.2
Simple Wizard Password. Max size 64
OBJECT-TYPE    
  OCTET STRING SIZE(0..64)  

wlSetup 1.3.6.1.4.1.2435.2.4.3.100.11
OBJECT IDENTIFIER    

wlGeneral 1.3.6.1.4.1.2435.2.4.3.100.11.1
OBJECT IDENTIFIER    

brpsWLanAPSetupMode 1.3.6.1.4.1.2435.2.4.3.100.11.1.1
AP setup mode status.
OBJECT-TYPE    
  INTEGER false(1), true(2)  

brpsWLanMode 1.3.6.1.4.1.2435.2.4.3.100.11.1.2
Wireless LAN mode.
OBJECT-TYPE    
  INTEGER dot11b-gAuto(1), dot11b(2), dot11g(3), dot11g-turbo(4)  

brpsWLanName 1.3.6.1.4.1.2435.2.4.3.100.11.1.3
The SSID setting.
OBJECT-TYPE    
  OCTET STRING SIZE(0..32)  

brpsWLanCommMode 1.3.6.1.4.1.2435.2.4.3.100.11.1.4
Wireless LAN communication mode.
OBJECT-TYPE    
  INTEGER infrastructure(1), ad-Hoc-WiFi(2), ad-Hoc(3)  

brpsWLanChannel 1.3.6.1.4.1.2435.2.4.3.100.11.1.5
Wireless LAN channel setting.
OBJECT-TYPE    
  INTEGER  

wlAdvanced 1.3.6.1.4.1.2435.2.4.3.100.11.5
OBJECT IDENTIFIER    

brpsWLanCtsMode 1.3.6.1.4.1.2435.2.4.3.100.11.5.1
Wireless LAN CTS mode setting.
OBJECT-TYPE    
  INTEGER auto(1), always(2), none(3)  

brpsWLanCtsRate 1.3.6.1.4.1.2435.2.4.3.100.11.5.2
Wireless LAN CTS rate setting. However, the unit is 1/10.
OBJECT-TYPE    
  INTEGER 0..32767  

brpsWLanCtsType 1.3.6.1.4.1.2435.2.4.3.100.11.5.3
Wireless LAN CTS type setting.
OBJECT-TYPE    
  INTEGER only(1), rts-cts(2)  

brpsWLanRtsCtsThreshold 1.3.6.1.4.1.2435.2.4.3.100.11.5.4
Wireless LAN RTS/CTS threshold setting.
OBJECT-TYPE    
  INTEGER 256..2346  

brpsWLanLengthThreshold 1.3.6.1.4.1.2435.2.4.3.100.11.5.5
Wireless LAN length threshold setting.
OBJECT-TYPE    
  INTEGER 256..2346  

brpsWLanDataRetry 1.3.6.1.4.1.2435.2.4.3.100.11.5.6
Wireless LAN DATA retyr setting.
OBJECT-TYPE    
  INTEGER 0..15  

brpsWLanTransmitPowerSetting 1.3.6.1.4.1.2435.2.4.3.100.11.5.7
Wireless LAN transmit power setting.
OBJECT-TYPE    
  INTEGER full(1), half(2), quarter(3), one-eighth(4), minimum(5), off(6)  

brpsWLanDeviceType 1.3.6.1.4.1.2435.2.4.3.100.11.5.8
Wireless LAN operation mode setting.
OBJECT-TYPE    
  INTEGER stationMode(1), accessPointMode(2)  

wlAssociate 1.3.6.1.4.1.2435.2.4.3.100.11.11
OBJECT IDENTIFIER    

brpsWLanEncryptMode 1.3.6.1.4.1.2435.2.4.3.100.11.11.1
Wireless LAN encrypt mode.
OBJECT-TYPE    
  INTEGER none(1), wep(2), tkip(3), aes(4)  

brpsWLanAuthMode 1.3.6.1.4.1.2435.2.4.3.100.11.11.11
Wireless LAN authenticate mode.
OBJECT-TYPE    
  INTEGER openSystem(1), sharedKey(2), wpa-psk(3), wpa-none(4), wpa(5), wpa2(6), leap(7), eapfast-none(8), eapfast-mschapv2(9), eapfast-gtc(10), eapfast-tls(11), wpa2-psk(12)  

brpsWLanAuthEAP 1.3.6.1.4.1.2435.2.4.3.100.11.11.12
Wireless LAN authenticate EAP.
OBJECT-TYPE    
  INTEGER eapMD5(1), eapTLS(2), eapTTLS(3), peap(4), leap(5), eapfast-none(6), eapfast-mschapv2(7), eapfast-gtc(8), eapfast-tls(9)  

brpsWLanAuthUserID 1.3.6.1.4.1.2435.2.4.3.100.11.11.13
Wireless LAN authenticate user ID.
OBJECT-TYPE    
  OCTET STRING SIZE(0..32)  

brpsWLanAuthUserPass 1.3.6.1.4.1.2435.2.4.3.100.11.11.14
Wireless LAN authenticate user password.
OBJECT-TYPE    
  OCTET STRING SIZE(0..32)  

brpsWLanAssociate 1.3.6.1.4.1.2435.2.4.3.100.11.11.21
Wireless LAN associate.
OBJECT-TYPE    
  INTEGER update(1), print(2), test(3), applyonly(4), simplewizard(5)  

brpsWLanAssociateTestResult 1.3.6.1.4.1.2435.2.4.3.100.11.11.22
Wireless LAN associate test result. 0 indicates cleared.
OBJECT-TYPE    
  INTEGER linkOK(1), noSuchWLan(2), invalidWLanNetKey(3), invalidAuthUserID(4), invalidAuthUserPass(5)  

brpsWLanAssociateResult 1.3.6.1.4.1.2435.2.4.3.100.11.11.23
Wireless LAN associate result. 0 indicates cleared.
OBJECT-TYPE    
  INTEGER linkOK(1), noSuchWLan(2), invalidWLanNetKey(3), invalidAuthUserID(4), invalidAuthUserPass(5)  

brpsWLanAssociateTestSupported 1.3.6.1.4.1.2435.2.4.3.100.11.11.24
0 indicates the Wireless network Associate Test function is not supported. 1 indicates the Wireless network Associate Test function is implemented by the firmware
OBJECT-TYPE    
  INTEGER  

wlWEP 1.3.6.1.4.1.2435.2.4.3.100.11.11.101
OBJECT IDENTIFIER    

brpsWLanWepKeyDefaultIndex 1.3.6.1.4.1.2435.2.4.3.100.11.11.101.1
The value of brpsWLanWepKeyIndex corresponding to the default setting.
OBJECT-TYPE    
  INTEGER  

brpsWLanWepKeyTable 1.3.6.1.4.1.2435.2.4.3.100.11.11.101.11
This table represents WEP KEY Info.
OBJECT-TYPE    
  SEQUENCE OF  
    BrpsWLanWepKeyEntry

brpsWLanWepKeyEntry 1.3.6.1.4.1.2435.2.4.3.100.11.11.101.11.1
A row in the brpsWLanWepKeyTable table. Rows cannot be created or deleted.
OBJECT-TYPE    
  BrpsWLanWepKeyEntry  

brpsWLanWepKeyIndex 1.3.6.1.4.1.2435.2.4.3.100.11.11.101.11.1.1
The number.
OBJECT-TYPE    
  INTEGER 1..4  

brpsWLanWepKeySize 1.3.6.1.4.1.2435.2.4.3.100.11.11.101.11.1.2
The WEP KEY size.
OBJECT-TYPE    
  INTEGER size40(1), size104(2)  

brpsWLanWepKeyType 1.3.6.1.4.1.2435.2.4.3.100.11.11.101.11.1.3
The WEP KEY type.
OBJECT-TYPE    
  INTEGER hex(1), ascii(2)  

brpsWLanWepKey 1.3.6.1.4.1.2435.2.4.3.100.11.11.101.11.1.4
The WEP KEY.
OBJECT-TYPE    
  OCTET STRING  

wlWPA 1.3.6.1.4.1.2435.2.4.3.100.11.11.102
OBJECT IDENTIFIER    

brpsWLanNetworkKey 1.3.6.1.4.1.2435.2.4.3.100.11.11.102.1
The WPA-PSK.
OBJECT-TYPE    
  OCTET STRING  

wlTKIP 1.3.6.1.4.1.2435.2.4.3.100.11.11.103
OBJECT IDENTIFIER    

brpsWLanTKIPChangeInterval 1.3.6.1.4.1.2435.2.4.3.100.11.11.103.1
TKIP Interval (s)
OBJECT-TYPE    
  INTEGER  

wlLEAP 1.3.6.1.4.1.2435.2.4.3.100.11.11.104
OBJECT IDENTIFIER    

brpsWLanLEAPTimeout 1.3.6.1.4.1.2435.2.4.3.100.11.11.104.1
Leap timeout (s)
OBJECT-TYPE    
  INTEGER  

wlStatus 1.3.6.1.4.1.2435.2.4.3.100.21
OBJECT IDENTIFIER    

wlGeneralStatus 1.3.6.1.4.1.2435.2.4.3.100.21.1
OBJECT IDENTIFIER    

brpsWLanOperatingMode 1.3.6.1.4.1.2435.2.4.3.100.21.1.1
The mode which is actually operating. off(0), dot11a(1), dot11b(2), dot11g(3)
OBJECT-TYPE    
  INTEGER  

brpsWLanRSSLevel 1.3.6.1.4.1.2435.2.4.3.100.21.1.2
Wireless LAN RSS Level.
OBJECT-TYPE    
  INTEGER 0..5  

brpsWLanCommSpeed 1.3.6.1.4.1.2435.2.4.3.100.21.1.3
Wireless LAN communication speed. However, the unit is 1/10.
OBJECT-TYPE    
  INTEGER 0..32767  

brpsWLanOperatingChannel 1.3.6.1.4.1.2435.2.4.3.100.21.1.4
Wireless LAN operating channel.
OBJECT-TYPE    
  INTEGER  

brpsWLanOperatingName 1.3.6.1.4.1.2435.2.4.3.100.21.1.5
Wireless LAN operating SSID Name.
OBJECT-TYPE    
  OCTET STRING  

brpsWLanOperatingCommMode 1.3.6.1.4.1.2435.2.4.3.100.21.1.6
Wireless LAN operating communication mode. off(0), infrastructure(1), ad-Hoc-WiFi(2), ad-Hoc(3)
OBJECT-TYPE    
  INTEGER  

brpsWLanOperatingEncryptMode 1.3.6.1.4.1.2435.2.4.3.100.21.1.7
Wireless LAN operating encrypt mode. off(0), none(1), wep(2), tkip(3), aes(4), ckip(5)
OBJECT-TYPE    
  INTEGER  

brpsWLanOperatingAuthMode 1.3.6.1.4.1.2435.2.4.3.100.21.1.8
Wireless LAN operating authenticate mode. off(0), openSystem(1), sharedKey(2), wpa-psk(3), wpa-none(4), wpa(5), wpa2(6), leap(7), eapfast-none(8), eapfast-mschapv2(9), eapfast-gtc(10), eapfast-tls(11), wpa2-psk(12)
OBJECT-TYPE    
  INTEGER  

brpsWLanOperatingWepKeyDefaultIndex 1.3.6.1.4.1.2435.2.4.3.100.21.1.9
Wireless LAN operating WepKeyDefaultIndex.
OBJECT-TYPE    
  INTEGER  

brnetConfig 1.3.6.1.4.1.2435.2.4.3.1240
OBJECT IDENTIFIER    

brconfig 1.3.6.1.4.1.2435.2.4.3.1240.1
OBJECT IDENTIFIER    

brpsNodeName 1.3.6.1.4.1.2435.2.4.3.1240.1.1
The node name of this print server.
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

brpsSerialNumber 1.3.6.1.4.1.2435.2.4.3.1240.1.2
The serial number of this print server.
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

brpsHardwareType 1.3.6.1.4.1.2435.2.4.3.1240.1.3
Hardware type of the print server.
OBJECT-TYPE    
  INTEGER 0..32767  

brpsMainRevision 1.3.6.1.4.1.2435.2.4.3.1240.1.4
Revision level of the Print Server firmware suitable for display. This object may be read but not written.
OBJECT-TYPE    
  DisplayString SIZE(0..5)  

brpsBootRevision 1.3.6.1.4.1.2435.2.4.3.1240.1.5
Revision level of the boot firmware (if applicable) suitable for display. This object may be read but not written.
OBJECT-TYPE    
  DisplayString SIZE(0..5)  

brpsPasswordVerify 1.3.6.1.4.1.2435.2.4.3.1240.1.6
Submit the print server's password for verification. An error will be returned if the password is incorrect.
OBJECT-TYPE    
  DisplayString  

brpsPassword 1.3.6.1.4.1.2435.2.4.3.1240.1.7
Set the print server's password value.
OBJECT-TYPE    
  DisplayString  

brpsMIBVersion 1.3.6.1.4.1.2435.2.4.3.1240.1.8
Revision level of the private MIB implemented by the device. For example: 1.0 This object may be read but not written.
OBJECT-TYPE    
  DisplayString SIZE(0..5)  

brpsOEMString 1.3.6.1.4.1.2435.2.4.3.1240.1.9
OEM string setting for the print server. This object may be read but not written.
OBJECT-TYPE    
  DisplayString SIZE(3)  

brpsMIBMajor 1.3.6.1.4.1.2435.2.4.3.1240.1.10
MIB major version number.
OBJECT-TYPE    
  INTEGER 0..9  

brpsMIBMinor 1.3.6.1.4.1.2435.2.4.3.1240.1.11
MIB minor version number.
OBJECT-TYPE    
  INTEGER 0..99  

brpsServerDescription 1.3.6.1.4.1.2435.2.4.3.1240.1.12
Product name of print server. For example: NC-3100h This object may be read but not written.
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

brpsEnetMode 1.3.6.1.4.1.2435.2.4.3.1240.1.13
Ethernet type.
OBJECT-TYPE    
  INTEGER 0..4  

brpsFlashROMSize 1.3.6.1.4.1.2435.2.4.3.1240.1.14
Flash ROM Size of print server (MBytes).
OBJECT-TYPE    
  INTEGER 0..255  

brpsSNMPGetCommunity 1.3.6.1.4.1.2435.2.4.3.1240.1.15
SNMP Get Community Name.
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

brpsSNMPJetAdmin 1.3.6.1.4.1.2435.2.4.3.1240.1.16
0 indicates the JetAdmin compatibility mode is not enabled. 1 indicates JetAdmin compatibility mode is enabled.
OBJECT-TYPE    
  INTEGER 0..1  

brpsSNMPSetCommunity1 1.3.6.1.4.1.2435.2.4.3.1240.1.17
SNMP Set Community Name #1.
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

brpsSNMPSetCommunity2 1.3.6.1.4.1.2435.2.4.3.1240.1.18
SNMP Set Community Name #2.
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

brSupportedInfo 1.3.6.1.4.1.2435.2.4.3.1240.1.200
OBJECT-TYPE    
  OCTET STRING SIZE(0..255)  

brcontrol 1.3.6.1.4.1.2435.2.4.3.1240.2
OBJECT IDENTIFIER    

brpsTestPage 1.3.6.1.4.1.2435.2.4.3.1240.2.1
Setting any value generates a test page on all ports.
OBJECT-TYPE    
  INTEGER 0..32767  

brpsSetDefault 1.3.6.1.4.1.2435.2.4.3.1240.2.2
Setting the value 5AA5h (23205) resets all parameters to their factory default value.
OBJECT-TYPE    
  INTEGER 0..32767  

brpsReset 1.3.6.1.4.1.2435.2.4.3.1240.2.3
Setting the value 55AAh (21930) causes the print server to perform a soft reset.
OBJECT-TYPE    
  INTEGER 0..32767  

brpsProtectModeEnable 1.3.6.1.4.1.2435.2.4.3.1240.2.4
0 indicates the protect mode is not enabled. 1 indicates protect mode is enabled.
OBJECT-TYPE    
  INTEGER 0..1  

brpsProtectPassword 1.3.6.1.4.1.2435.2.4.3.1240.2.5
protect password.
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

brport 1.3.6.1.4.1.2435.2.4.3.1240.3
OBJECT IDENTIFIER    

brpsPortCount 1.3.6.1.4.1.2435.2.4.3.1240.3.1
Number of ports on this print server.
OBJECT-TYPE    
  INTEGER 0..32  

brpsPortInfoTable 1.3.6.1.4.1.2435.2.4.3.1240.3.2
This table represents the attributes of a port.
OBJECT-TYPE    
  SEQUENCE OF  
    BrpsPortInfoEntry

brpsPortInfoEntry 1.3.6.1.4.1.2435.2.4.3.1240.3.2.1
A row in the port table. Rows cannot be created or deleted via direct SNMP operations.
OBJECT-TYPE    
  BrpsPortInfoEntry  

brpsPortIndex 1.3.6.1.4.1.2435.2.4.3.1240.3.2.1.1
The port number.
OBJECT-TYPE    
  INTEGER 1..255  

brpsPortName 1.3.6.1.4.1.2435.2.4.3.1240.3.2.1.2
The port name.
OBJECT-TYPE    
  DisplayString SIZE(1..32)  

brpsPortType 1.3.6.1.4.1.2435.2.4.3.1240.3.2.1.3
Type of port.
OBJECT-TYPE    
  INTEGER parallel(1), serial(2)  

brpsPortStatus 1.3.6.1.4.1.2435.2.4.3.1240.3.2.1.4
The port status as a 32 bit integer.
OBJECT-TYPE    
  INTEGER 0..31  

brpsPortStatusString 1.3.6.1.4.1.2435.2.4.3.1240.3.2.1.5
The port status description. Reflects the printer's front panel display on internal print server interfaces.
OBJECT-TYPE    
  DisplayString SIZE(1..32)  

brpsPortProtocol 1.3.6.1.4.1.2435.2.4.3.1240.3.2.1.6
Protocol currently printing on this port.
OBJECT-TYPE    
  INTEGER 0..12  

brpsPortQueueSize 1.3.6.1.4.1.2435.2.4.3.1240.3.2.1.7
Number of protocols waiting to print on this port.
OBJECT-TYPE    
  INTEGER  

brpsPortDescriptionString 1.3.6.1.4.1.2435.2.4.3.1240.3.2.1.8
The port description. Reflects the device ID of the printer connected to the port.
OBJECT-TYPE    
  DisplayString SIZE(1..50)  

brpsPortInfoString 1.3.6.1.4.1.2435.2.4.3.1240.3.2.1.9
The port status information. More information about the port status.
OBJECT-TYPE    
  DisplayString SIZE(1..255)  

brpsPortHTTPExtensions 1.3.6.1.4.1.2435.2.4.3.1240.3.2.1.10
0 indicates the printer on this port does not support HTTP, 1 indicates that the printer does support HTTP.
OBJECT-TYPE    
  INTEGER 0..1  

brpsPortSNMPExtensions 1.3.6.1.4.1.2435.2.4.3.1240.3.2.1.11
0 indicates the printer on this port does not support SNMP, 1 indicates that the printer does support SNMP.
OBJECT-TYPE    
  INTEGER 0..1  

brpsPortAttribute 1.3.6.1.4.1.2435.2.4.3.1240.3.2.1.12
Port attribute.
OBJECT-TYPE    
  DisplayString SIZE(1..32)  

brpsPortBinaryMode 1.3.6.1.4.1.2435.2.4.3.1240.3.2.1.13
Port binary mode.
OBJECT-TYPE    
  INTEGER 0..3  

brpsPortInhibitDatagramSupport 1.3.6.1.4.1.2435.2.4.3.1240.3.2.1.14
0 indicates the inhibit datagram is not supported. 1 indicates the inhibit datagram is supported.
OBJECT-TYPE    
  INTEGER 0..1  

brservice 1.3.6.1.4.1.2435.2.4.3.1240.4
OBJECT IDENTIFIER    

brpsServiceCount 1.3.6.1.4.1.2435.2.4.3.1240.4.1
Number of services on this print server.
OBJECT-TYPE    
  INTEGER 0..128  

brpsServiceInfoTable 1.3.6.1.4.1.2435.2.4.3.1240.4.2
This table represents the attributes of a service.
OBJECT-TYPE    
  SEQUENCE OF  
    BrpsServiceInfoEntry

brpsServiceInfoEntry 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1
A row in the services table. Rows cannot be created or deleted via direct SNMP operations.
OBJECT-TYPE    
  BrpsServiceInfoEntry  

brpsServiceIndex 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.1
The service number.
OBJECT-TYPE    
  INTEGER 1..32  

brpsServiceName 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.2
The service name.
OBJECT-TYPE    
  DisplayString SIZE(1..32)  

brpsServicePort 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.3
The port number assigned to this service.
OBJECT-TYPE    
  INTEGER 0..31  

brpsServiceFilter 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.4
Filter number assigned to this service.
OBJECT-TYPE    
  INTEGER 0..255  

brpsServiceBOT 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.5
Beginning of text string number assigned to this service.
OBJECT-TYPE    
  INTEGER 0..255  

brpsServiceEOT 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.6
End of text string number assigned to this service.
OBJECT-TYPE    
  INTEGER 0..255  

brpsServiceMatch 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.7
Match string number assigned to this service.
OBJECT-TYPE    
  INTEGER 0..255  

brpsServiceReplace 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.8
Replace string number assigned to this service.
OBJECT-TYPE    
  INTEGER 0..255  

brpsServiceTCPPort 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.9
TCP Port number assigned to this service.
OBJECT-TYPE    
  INTEGER 0..65535  

brpsServiceNDSTree 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.10
The NDS Tree.
OBJECT-TYPE    
  DisplayString SIZE(1..48)  

brpsServiceNDSContext 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.11
The NDS Context in Unicode.
OBJECT-TYPE    
  OCTET STRING SIZE(0..255)  

brpsServiceVines 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.12
The Vines StreetTalk name for this service.
OBJECT-TYPE    
  DisplayString SIZE(1..48)  

brpsServiceObsolete 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.13
Obsolete parameter that is no longer used
OBJECT-TYPE    
  INTEGER 0..127  

brpsServiceNetwareServerCount 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.14
The number of Netware servers enabled on this service. Modifying the value will truncate the server list to the specified number of servers. If the value set is greater than the number of servers currently on the list, then the list will be unchanged.
OBJECT-TYPE    
  INTEGER 0..127  

brpsServiceReceiveOnly 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.15
When enabled, the service will only receive data, any printer responses will be discarded.
OBJECT-TYPE    
  INTEGER 0..1  

brpsServiceTCPQueued 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.16
When enabled, the raw TCP connections to the port will be queued while waiting for the port to become available
OBJECT-TYPE    
  INTEGER 0..1  

brpsServiceProtocolLAT 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.17
When enabled, the LAT protocol will be available on this service.
OBJECT-TYPE    
  INTEGER 0..1  

brpsServiceProtocolTCPIP 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.18
When enabled, the TCP/IP protocol will be available on this service.
OBJECT-TYPE    
  INTEGER 0..1  

brpsServiceProtocolNetware 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.19
When enabled, the Netware protocol will be available on this service.
OBJECT-TYPE    
  INTEGER 0..1  

brpsServiceProtocolAppleTalk 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.20
When enabled, the AppleTalk protocol will be available on this service.
OBJECT-TYPE    
  INTEGER 0..1  

brpsServiceProtocolBanyan 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.21
When enabled, the Banyan protocol will be available on this service.
OBJECT-TYPE    
  INTEGER 0..1  

brpsServiceProtocolDLC 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.22
When enabled, the DLC protocol will be available on this service.
OBJECT-TYPE    
  INTEGER 0..1  

brpsServiceProtocolNetBEUI 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.23
When enabled, the NetBEUI protocol will be available on this service.
OBJECT-TYPE    
  INTEGER 0..1  

brpsServiceNetwareServerMode 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.24
Netware mode for this service. 0 = Queue Server, 1 = Remote Printer
OBJECT-TYPE    
  INTEGER 0..1  

brpsServiceNetwareRemotePrinterNum 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.25
Remote Printer Number for this service
OBJECT-TYPE    
  INTEGER 0..255  

brpsServiceProtocolIPP 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.26
When enabled, the IPP protocol will be available on this service.
OBJECT-TYPE    
  INTEGER 0..1  

brpsServiceAppleTalkType 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.27
AppleTalk type.
OBJECT-TYPE    
  DisplayString SIZE(1..32)  

brpsServiceStringLimit 1.3.6.1.4.1.2435.2.4.3.1240.4.3
Maximum number of service strings supported by the print server.
OBJECT-TYPE    
  INTEGER 1..127  

brpsServiceStringInfoTable 1.3.6.1.4.1.2435.2.4.3.1240.4.4
This table represents the service BOT/EOT/MATCH/REPLACE strings defined.
OBJECT-TYPE    
  SEQUENCE OF  
    BrpsServiceStringInfoEntry

brpsServiceStringInfoEntry 1.3.6.1.4.1.2435.2.4.3.1240.4.4.1
A row in the service string table. Rows cannot be created or deleted via direct SNMP operations.
OBJECT-TYPE    
  BrpsServiceStringInfoEntry  

brpsServiceStringIndex 1.3.6.1.4.1.2435.2.4.3.1240.4.4.1.1
The string number.
OBJECT-TYPE    
  INTEGER 1..255  

brpsServiceString 1.3.6.1.4.1.2435.2.4.3.1240.4.4.1.2
The character string definition suitable for displaying.
OBJECT-TYPE    
  DisplayString SIZE(1..32)  

brpsServiceStringCount 1.3.6.1.4.1.2435.2.4.3.1240.4.5
Number of service strings currently defined on the print server.
OBJECT-TYPE    
  INTEGER  

brpsServiceFilterCount 1.3.6.1.4.1.2435.2.4.3.1240.4.6
Number of service filters implemented by the device.
OBJECT-TYPE    
  INTEGER  

brprotocol 1.3.6.1.4.1.2435.2.4.3.1240.5
OBJECT IDENTIFIER    

brlat 1.3.6.1.4.1.2435.2.4.3.1240.5.1
OBJECT IDENTIFIER    

brpsLATSupported 1.3.6.1.4.1.2435.2.4.3.1240.5.1.1
0 indicates the LAT protocol is not supported. 1 indicates LAT support is implemented by the firmware
OBJECT-TYPE    
  INTEGER 0..1  

brpsLATEnable 1.3.6.1.4.1.2435.2.4.3.1240.5.1.2
0 indicates the LAT protocol is not enabled. 1 indicates that the LAT protocol is enabled. Writing a non-zero value will enable the LAT protocol if it is supported by the firmware.
OBJECT-TYPE    
  INTEGER 0..1  

brpsLATCircuitTimer 1.3.6.1.4.1.2435.2.4.3.1240.5.1.3
Minimum time (in milliseconds) between transmissions to the host. The default of 10 normally provides the best performance.
OBJECT-TYPE    
  INTEGER 10..499  

brpsLATKeepAliveTimer 1.3.6.1.4.1.2435.2.4.3.1240.5.1.4
How often in seconds a packet is transmitted to keep a connection alive.
OBJECT-TYPE    
  INTEGER 0..60000  

brpsLATReceiveBufferMax 1.3.6.1.4.1.2435.2.4.3.1240.5.1.5
LAT receive buffer max size.
OBJECT-TYPE    
  INTEGER 0..5  

brpsLATTransmitBufferMax 1.3.6.1.4.1.2435.2.4.3.1240.5.1.6
LAT transmit buffer max size.
OBJECT-TYPE    
  INTEGER 0..5  

brpsLATTimeout 1.3.6.1.4.1.2435.2.4.3.1240.5.1.7
LAT inactivity timeout (sec).
OBJECT-TYPE    
  INTEGER 0..499  

brpsLATGroup 1.3.6.1.4.1.2435.2.4.3.1240.5.1.8
LAT group membership (mm-[nn]).
OBJECT-TYPE    
  DisplayString SIZE(1..7)  

brtcpip 1.3.6.1.4.1.2435.2.4.3.1240.5.2
OBJECT IDENTIFIER    

brpsTCPIPSupported 1.3.6.1.4.1.2435.2.4.3.1240.5.2.1
0 indicates the TCP/IP protocol is not supported. 1 indicates TCP/IP support is implemented by the firmware
OBJECT-TYPE    
  INTEGER 0..1  

brpsTCPIPEnable 1.3.6.1.4.1.2435.2.4.3.1240.5.2.2
0 indicates the TCP/IP protocol is not enabled. 1 indicates that the TCP/IP protocol is enabled. Writing a non-zero value will enable the TCP/IP protocol if it is supported by the firmware.
OBJECT-TYPE    
  INTEGER 0..1  

brpsTCPIPAddress 1.3.6.1.4.1.2435.2.4.3.1240.5.2.3
IP Address assigned to the print server.
OBJECT-TYPE    
  IpAddress  

brpsTCPIPSubnetMask 1.3.6.1.4.1.2435.2.4.3.1240.5.2.4
Subnet mask assigned to the print server.
OBJECT-TYPE    
  IpAddress  

brpsTCPIPGateway 1.3.6.1.4.1.2435.2.4.3.1240.5.2.5
Gateway/Router address assigned to the print server.
OBJECT-TYPE    
  IpAddress  

brpsTCPIPMethod 1.3.6.1.4.1.2435.2.4.3.1240.5.2.6
Method used to determine the IP Address. AUTO tries all protocols. STATIC uses the configured address. DHCP, BOOTP, and RARP use only that protocol.
OBJECT-TYPE    
  INTEGER 0..7  

brpsTCPIPTimeout 1.3.6.1.4.1.2435.2.4.3.1240.5.2.7
Timeout used for LPD connections.
OBJECT-TYPE    
  INTEGER 0..32767  

brpsTCPIPBootTries 1.3.6.1.4.1.2435.2.4.3.1240.5.2.8
Number of attempts to use BOOTP, RARP, and DHCP.
OBJECT-TYPE    
  INTEGER 0..32767  

brpsTCPIPMaxWindow 1.3.6.1.4.1.2435.2.4.3.1240.5.2.9
Maximum window size for TCP connections. Due to resource limitations setting the window to values greater than 10240 is not recommended.
OBJECT-TYPE    
  INTEGER 1500..65535  

brpsTCPIPRARPNoSubnet 1.3.6.1.4.1.2435.2.4.3.1240.5.2.10
If enabled, do not set the subnet mask based on the RARP response.
OBJECT-TYPE    
  INTEGER 0..1  

brpsTCPIPRARPNoGateway 1.3.6.1.4.1.2435.2.4.3.1240.5.2.11
If enabled, do not set the gateway/router address based on the RARP response.
OBJECT-TYPE    
  INTEGER 0..1  

brpsTCPIPUpdate 1.3.6.1.4.1.2435.2.4.3.1240.5.2.12
Hardware MAC address to be updated. This value is write only. Will read back as zeros.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

brpsTCPIPBanner 1.3.6.1.4.1.2435.2.4.3.1240.5.2.13
0 indicates the LPR banner print is not enabled. 1 indicates that the LPR banner print is enabled.
OBJECT-TYPE    
  INTEGER 0..1  

brpsTCPIPFastTimeoutEnable 1.3.6.1.4.1.2435.2.4.3.1240.5.2.14
0 indicates the fast timeout is not enabled. 1 indicates that the fast timeout is enabled.
OBJECT-TYPE    
  INTEGER 0..1  

brpsTCPIPLPRRetryEnable 1.3.6.1.4.1.2435.2.4.3.1240.5.2.15
0 indicates the LPR print retry is not enabled. 1 indicates that the LPR print retry is enabled.
OBJECT-TYPE    
  INTEGER 0..1  

brpsTCPIPUseMethod 1.3.6.1.4.1.2435.2.4.3.1240.5.2.16
Method type that used set up TCP/IP configuration.
OBJECT-TYPE    
  INTEGER 0..7  

brpsTCPIPMethodServer 1.3.6.1.4.1.2435.2.4.3.1240.5.2.17
If TCP/IP configuration is setted up by any protocol server, this entry indicates the IP address of the server.
OBJECT-TYPE    
  IpAddress  

brpsTCPIPAccessTable 1.3.6.1.4.1.2435.2.4.3.1240.5.2.18
This table represents the list of IP address of node that has parmittion for access.Up to 16 Netware addresses can be enabled.
OBJECT-TYPE    
  SEQUENCE OF  
    BrpsTCPIPAccessEntry

brpsTCPIPAccessEntry 1.3.6.1.4.1.2435.2.4.3.1240.5.2.18.1
A row in the TCP/IP access table. Rows cannot be created or deleted via direct SNMP operations.
OBJECT-TYPE    
  BrpsTCPIPAccessEntry  

brpsTCPIPAccessIndex 1.3.6.1.4.1.2435.2.4.3.1240.5.2.18.1.1
The TCP/IP access table's index.
OBJECT-TYPE    
  INTEGER 1..16  

brpsTCPIPAccessNodeAddress 1.3.6.1.4.1.2435.2.4.3.1240.5.2.18.1.2
IP address of node that has parmittion for access.
OBJECT-TYPE    
  IpAddress  

brpsTCPIPAccessSubnetMask 1.3.6.1.4.1.2435.2.4.3.1240.5.2.18.1.3
Subnet mask of node that has parmittion for access.
OBJECT-TYPE    
  IpAddress  

brpsAdvancedTCPIPAccessSupported 1.3.6.1.4.1.2435.2.4.3.1240.5.2.19
0 indicates the Advanced TCP/IP Access is not supported. 1 indicates Advanced TCP/IP Access support is implemented by the firmware
OBJECT-TYPE    
  INTEGER 0..1  

brpsAdvancedTCPIPAccessEnable 1.3.6.1.4.1.2435.2.4.3.1240.5.2.20
0 indicates the Advanced TCP/IP Access is not enabled. 1 indicates that the Advanced TCP/IP Access is enabled.
OBJECT-TYPE    
  INTEGER 0..1  

brpsAdvancedTCPIPAccessAdministratorIPAddress 1.3.6.1.4.1.2435.2.4.3.1240.5.2.21
Administrator IPAddress.
OBJECT-TYPE    
  IpAddress  

brpsAdvancedTCPIPAccessSetting 1.3.6.1.4.1.2435.2.4.3.1240.5.2.22
0 indicates the Advanced TCP/IP Access is reject. 1 indicates that the Advanced TCP/IP Access is Accept.
OBJECT-TYPE    
  INTEGER 0..1  

brnetware 1.3.6.1.4.1.2435.2.4.3.1240.5.3
OBJECT IDENTIFIER    

brpsNetwareSupported 1.3.6.1.4.1.2435.2.4.3.1240.5.3.1
0 indicates the Netware protocol is not supported. 1 indicates Netware support is implemented by the firmware. 2 indicates that Netware NEST NDS support is implemented by the firmware.
OBJECT-TYPE    
  INTEGER 0..2  

brpsNetwareEnable 1.3.6.1.4.1.2435.2.4.3.1240.5.3.2
0 indicates the Netware protocol is not enabled. 1 indicates that the Netware protocol is enabled. Writing a non-zero value will enable the Netware protocol if it is supported by the firmware.
OBJECT-TYPE    
  INTEGER 0..1  

brpsNetwareFrameType 1.3.6.1.4.1.2435.2.4.3.1240.5.3.3
The frame type to be used as follows: 0 = Automatic, 1 = Ethernet 802.3, 2 = Ethernet II, 3 = Ethernet 802.2, 4 = Ethernet SNAP.
OBJECT-TYPE    
  INTEGER 0..4  

brpsNetwarePollFreq 1.3.6.1.4.1.2435.2.4.3.1240.5.3.4
File server polling frequency in seconds.
OBJECT-TYPE    
  INTEGER 2..60  

brpsNetwareAdvFreq 1.3.6.1.4.1.2435.2.4.3.1240.5.3.5
Print server advertising frequency in seconds.
OBJECT-TYPE    
  INTEGER 0..210  

brpsNetwarePassword 1.3.6.1.4.1.2435.2.4.3.1240.5.3.6
The Netware login password.
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

brpsNetwareRestart 1.3.6.1.4.1.2435.2.4.3.1240.5.3.7
Setting any value will restart the Netware protocol.
OBJECT-TYPE    
  INTEGER 0..1  

brpsNetwareServerTable 1.3.6.1.4.1.2435.2.4.3.1240.5.3.8
This table represents the list of enabled Netware servers. Up to 16 Netware servers can be enabled. If the service is configured for remote printer mode, then only the first enabled server is used and it should specify a print server.
OBJECT-TYPE    
  SEQUENCE OF  
    BrpsNetwareServerEntry

brpsNetwareServerEntry 1.3.6.1.4.1.2435.2.4.3.1240.5.3.8.1
A row in the Netware server table. Rows cannot be created or deleted via direct SNMP operations.
OBJECT-TYPE    
  BrpsNetwareServerEntry  

brpsNetwareServerIndex 1.3.6.1.4.1.2435.2.4.3.1240.5.3.8.1.1
The Netware server number.
OBJECT-TYPE    
  INTEGER 1..16  

brpsNetwareServerName 1.3.6.1.4.1.2435.2.4.3.1240.5.3.8.1.2
The Netware server name. Specifies a print server if the service is in remote printer mode, or a file server if the service is in queue server mode
OBJECT-TYPE    
  DisplayString SIZE(1..48)  

brpsNetwarePasswordSet 1.3.6.1.4.1.2435.2.4.3.1240.5.3.9
Returns 1 if the Netware login password is set, 0 if not set.
OBJECT-TYPE    
  INTEGER 0..1  

brpsNDSSupported 1.3.6.1.4.1.2435.2.4.3.1240.5.3.10
0 indicates NDS is not supported. 1 indicates NDS is implemented by the firmware
OBJECT-TYPE    
  INTEGER 0..1  

brpsNetwareEtherIINetInfo 1.3.6.1.4.1.2435.2.4.3.1240.5.3.11
Ethernet II network information.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

brpsNetwareEtherIICount 1.3.6.1.4.1.2435.2.4.3.1240.5.3.12
Ethernet II network counter
OBJECT-TYPE    
  INTEGER 0..65535  

brpsNetware8022NetInfo 1.3.6.1.4.1.2435.2.4.3.1240.5.3.13
IEEE 802.2 network information.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

brpsNetware8022Count 1.3.6.1.4.1.2435.2.4.3.1240.5.3.14
IEEE 802.2 network counter.
OBJECT-TYPE    
  INTEGER 0..65535  

brpsNetware8023NetInfo 1.3.6.1.4.1.2435.2.4.3.1240.5.3.15
IEEE 802.3 network information.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

brpsNetware8023Count 1.3.6.1.4.1.2435.2.4.3.1240.5.3.16
IEEE 802.3 network information.
OBJECT-TYPE    
  INTEGER 0..65535  

brpsNetwareSNAPNetInfo 1.3.6.1.4.1.2435.2.4.3.1240.5.3.17
SNAP network information.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

brpsNetwareSNAPCount 1.3.6.1.4.1.2435.2.4.3.1240.5.3.18
SNAP network count.
OBJECT-TYPE    
  INTEGER 0..65535  

brpsNetwareServicingServerName 1.3.6.1.4.1.2435.2.4.3.1240.5.3.19
Netware server name.
OBJECT-TYPE    
  DisplayString SIZE(1..48)  

brpsNetwareServicingQueueName 1.3.6.1.4.1.2435.2.4.3.1240.5.3.20
Netware queue name.
OBJECT-TYPE    
  DisplayString SIZE(1..48)  

brpsNetwareServicingServerCount 1.3.6.1.4.1.2435.2.4.3.1240.5.3.21
Number of netware servers.
OBJECT-TYPE    
  INTEGER 0..255  

brpsNetwareServicingQueueCount 1.3.6.1.4.1.2435.2.4.3.1240.5.3.22
Number of netware queues.
OBJECT-TYPE    
  INTEGER 0..255  

brpsNetwarePrintJob 1.3.6.1.4.1.2435.2.4.3.1240.5.3.23
Number of netware print job.
OBJECT-TYPE    
  INTEGER 0..65535  

brappletalk 1.3.6.1.4.1.2435.2.4.3.1240.5.4
OBJECT IDENTIFIER    

brpsAppleTalkSupported 1.3.6.1.4.1.2435.2.4.3.1240.5.4.1
0 indicates the AppleTalk protocol is not supported. 1 indicates AppleTalk support is implemented by the firmware
OBJECT-TYPE    
  INTEGER 0..1  

brpsAppleTalkEnable 1.3.6.1.4.1.2435.2.4.3.1240.5.4.2
0 indicates the AppleTalk protocol is not enabled. 1 indicates that the AppleTalk protocol is enabled. Writing a non-zero value will enable the AppleTalk protocol if it is supported by the firmware.
OBJECT-TYPE    
  INTEGER 0..1  

brpsAppleTalkZone 1.3.6.1.4.1.2435.2.4.3.1240.5.4.3
The AppleTalk zone the print server belongs to.
OBJECT-TYPE    
  DisplayString  

brpsAppleTalkPrintJob 1.3.6.1.4.1.2435.2.4.3.1240.5.4.4
Counter of AppleTalk print job.
OBJECT-TYPE    
  INTEGER 0..65535  

brpsAppleTalkReadByte 1.3.6.1.4.1.2435.2.4.3.1240.5.4.5
Counter of read bytes.
OBJECT-TYPE    
  INTEGER 0..65535  

brpsAppleTalkWriteByte 1.3.6.1.4.1.2435.2.4.3.1240.5.4.6
Counter of write bytes.
OBJECT-TYPE    
  INTEGER 0..65535  

brpsAppleTalkReadError 1.3.6.1.4.1.2435.2.4.3.1240.5.4.7
Counter of read error.
OBJECT-TYPE    
  INTEGER 0..65535  

brpsAppleTalkWriteError 1.3.6.1.4.1.2435.2.4.3.1240.5.4.8
Counter of write error.
OBJECT-TYPE    
  INTEGER 0..65535  

brbanyan 1.3.6.1.4.1.2435.2.4.3.1240.5.5
OBJECT IDENTIFIER    

brpsBanyanSupported 1.3.6.1.4.1.2435.2.4.3.1240.5.5.1
0 indicates the Banyan protocol is not supported. 1 indicates Banyan support is implemented by the firmware
OBJECT-TYPE    
  INTEGER 0..1  

brpsBanyanEnable 1.3.6.1.4.1.2435.2.4.3.1240.5.5.2
0 indicates the Banyan protocol is not enabled. 1 indicates that the Banyan protocol is enabled. Writing a non-zero value will enable the Banyan protocol if is is supported by the firmware.
OBJECT-TYPE    
  INTEGER 0..1  

brpsBanyanLoginName 1.3.6.1.4.1.2435.2.4.3.1240.5.5.3
The Banyan login name.
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

brpsBanyanPassword 1.3.6.1.4.1.2435.2.4.3.1240.5.5.4
The Banyan login password.
OBJECT-TYPE    
  DisplayString SIZE(0..16)  

brpsBanyanHopCount 1.3.6.1.4.1.2435.2.4.3.1240.5.5.5
Number of hops between the print server and the Banyan file server.
OBJECT-TYPE    
  INTEGER 0..32767  

brpsBanyanTimeout 1.3.6.1.4.1.2435.2.4.3.1240.5.5.6
Timeout in seconds for a Banyan print job.
OBJECT-TYPE    
  INTEGER 0..32767  

brpsBanyanPasswordSet 1.3.6.1.4.1.2435.2.4.3.1240.5.5.7
Returns 1 if the Banyan login password is set, 0 if not set.
OBJECT-TYPE    
  INTEGER 0..1  

brpsBanyanIPNetworkID1 1.3.6.1.4.1.2435.2.4.3.1240.5.5.8
IP Network ID.
OBJECT-TYPE    
  OCTET STRING SIZE(8)  

brpsBanyanIPNetworkID2 1.3.6.1.4.1.2435.2.4.3.1240.5.5.9
IP Network ID.
OBJECT-TYPE    
  OCTET STRING SIZE(4)  

brpsBanyanRouter1 1.3.6.1.4.1.2435.2.4.3.1240.5.5.10
Router ID.
OBJECT-TYPE    
  OCTET STRING SIZE(8)  

brpsBanyanRouter2 1.3.6.1.4.1.2435.2.4.3.1240.5.5.11
Router ID.
OBJECT-TYPE    
  OCTET STRING SIZE(4)  

brpsBanyanIPPacket 1.3.6.1.4.1.2435.2.4.3.1240.5.5.12
Counter of IP Packet.
OBJECT-TYPE    
  INTEGER 0..65535  

brpsBanyanErrorCS 1.3.6.1.4.1.2435.2.4.3.1240.5.5.13
Counter of CS error.
OBJECT-TYPE    
  INTEGER 0..65535  

brpsBanyanErrorPT 1.3.6.1.4.1.2435.2.4.3.1240.5.5.14
Counter of PT error.
OBJECT-TYPE    
  INTEGER 0..65535  

brpsBanyanErrorLE 1.3.6.1.4.1.2435.2.4.3.1240.5.5.15
Counter of LE error.
OBJECT-TYPE    
  INTEGER 0..65535  

brpsBanyanPrintServerStatus 1.3.6.1.4.1.2435.2.4.3.1240.5.5.16
Banyan print server status.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

brpsBanyanServerAddress1 1.3.6.1.4.1.2435.2.4.3.1240.5.5.17
Banyan server address.
OBJECT-TYPE    
  OCTET STRING SIZE(8)  

brpsBanyanServerAddress2 1.3.6.1.4.1.2435.2.4.3.1240.5.5.18
Banyan server address.
OBJECT-TYPE    
  OCTET STRING SIZE(4)  

brpsBanyanIPCConnectionInformation 1.3.6.1.4.1.2435.2.4.3.1240.5.5.19
IPC connection information.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

brpsBanyanIPCSequenceError 1.3.6.1.4.1.2435.2.4.3.1240.5.5.20
IPC sequence error.
OBJECT-TYPE    
  INTEGER 0..65535  

brpsBanyanIPCListen 1.3.6.1.4.1.2435.2.4.3.1240.5.5.21
IPC listen.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

brpsBanyanSPPConnectionInformation 1.3.6.1.4.1.2435.2.4.3.1240.5.5.22
SPP connection information.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

brpsBanyanSPPSequenceError 1.3.6.1.4.1.2435.2.4.3.1240.5.5.23
SPP sequence error.
OBJECT-TYPE    
  INTEGER 0..65535  

brpsBanyanSPPListen 1.3.6.1.4.1.2435.2.4.3.1240.5.5.24
SPP listen.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

bremail 1.3.6.1.4.1.2435.2.4.3.1240.5.6
OBJECT IDENTIFIER    

brpsEmailSupported 1.3.6.1.4.1.2435.2.4.3.1240.5.6.1
0 indicates the POP3/SMTP email protocols are not supported. 1 indicates email support is implemented by the firmware
OBJECT-TYPE    
  INTEGER 0..1  

brpsEmailEnable 1.3.6.1.4.1.2435.2.4.3.1240.5.6.2
0 indicates the POP3/SMTP email protocols are not enabled. 1 indicates that the email protocols are enabled. Writing a non-zero value will enable the email protocols if they are supported by the firmware.
OBJECT-TYPE    
  INTEGER 0..1  

brpsPOP3Address 1.3.6.1.4.1.2435.2.4.3.1240.5.6.3
The IP Address of the POP3 server.
OBJECT-TYPE    
  IpAddress  

brpsSMTPAddress 1.3.6.1.4.1.2435.2.4.3.1240.5.6.4
The IP Address of the SMTP server.
OBJECT-TYPE    
  IpAddress  

brpsPOP3Name 1.3.6.1.4.1.2435.2.4.3.1240.5.6.5
The POP3 mailbox name.
OBJECT-TYPE    
  DisplayString  

brpsPOP3Password 1.3.6.1.4.1.2435.2.4.3.1240.5.6.6
The POP3 mailbox password.
OBJECT-TYPE    
  DisplayString  

brpsPOP3PollFreq 1.3.6.1.4.1.2435.2.4.3.1240.5.6.7
The POP3 polling frequency in seconds.
OBJECT-TYPE    
  INTEGER 10..32767  

brpsPOP3Timeout 1.3.6.1.4.1.2435.2.4.3.1240.5.6.8
The POP3 timeout in minutes.
OBJECT-TYPE    
  INTEGER 10..32767  

brpsPOP3PasswordSet 1.3.6.1.4.1.2435.2.4.3.1240.5.6.9
Returns 1 if the POP3 password is set, 0 if not set.
OBJECT-TYPE    
  INTEGER 0..1  

brpsPOP3TotalMessage 1.3.6.1.4.1.2435.2.4.3.1240.5.6.10
Counter of POP3 message.
OBJECT-TYPE    
  INTEGER 0..65535  

brpsPOP3TotalConnect 1.3.6.1.4.1.2435.2.4.3.1240.5.6.11
Counter of POP3 connect.
OBJECT-TYPE    
  INTEGER 0..65535  

brpsPOP3TotalConnectFailure 1.3.6.1.4.1.2435.2.4.3.1240.5.6.12
Counter of POP3 connect error.
OBJECT-TYPE    
  INTEGER 0..65535  

brpsPOP3TotalConnectionLost 1.3.6.1.4.1.2435.2.4.3.1240.5.6.13
Counter of POP3 connection lost.
OBJECT-TYPE    
  INTEGER 0..65535  

brpsPOP3TotalUserFailure 1.3.6.1.4.1.2435.2.4.3.1240.5.6.14
Counter of POP3 user error.
OBJECT-TYPE    
  INTEGER 0..65535  

brpsPOP3TotalPasswordFailure 1.3.6.1.4.1.2435.2.4.3.1240.5.6.15
Counter of POP3 pass error.
OBJECT-TYPE    
  INTEGER 0..65535  

brpsPOP3TotalIOError 1.3.6.1.4.1.2435.2.4.3.1240.5.6.16
Counter of POP3 I/O error.
OBJECT-TYPE    
  INTEGER 0..65535  

brpsSMTPTotalMessage 1.3.6.1.4.1.2435.2.4.3.1240.5.6.17
Counter of SMTP message.
OBJECT-TYPE    
  INTEGER 0..65535  

brpsSMTPTotalConnect 1.3.6.1.4.1.2435.2.4.3.1240.5.6.18
Counter of SMTP connect.
OBJECT-TYPE    
  INTEGER 0..65535  

brpsSMTPTotalConnectFailure 1.3.6.1.4.1.2435.2.4.3.1240.5.6.19
Counter of SMTP connect error.
OBJECT-TYPE    
  INTEGER 0..65535  

brpsSMTPTotalRecvFromFailure 1.3.6.1.4.1.2435.2.4.3.1240.5.6.20
Counter of SMTP recvfrom error.
OBJECT-TYPE    
  INTEGER 0..65535  

brpsSMTPTotalSendToFailure 1.3.6.1.4.1.2435.2.4.3.1240.5.6.21
Counter of SMTP recvfrom error.
OBJECT-TYPE    
  INTEGER 0..65535  

brpsPOP3Supported 1.3.6.1.4.1.2435.2.4.3.1240.5.6.101
0 indicates the POP3 protocol is not supported. 1 indicates the POP3 protocol is implemented by the firmware
OBJECT-TYPE    
  INTEGER 0..1  

brpsSMTPServerAuthMethod 1.3.6.1.4.1.2435.2.4.3.1240.5.6.102
0 indicates the user is not authenticated to the SMTP Server. 1 indicates the user is authenticated to the SMTP Server using SMTP-AUTH. 2 indicates the user is authenticated to the SMTP Server using POP before SMTP.
OBJECT-TYPE    
  INTEGER 0..2  

brpsSMTPAUTHUsername 1.3.6.1.4.1.2435.2.4.3.1240.5.6.103
The username of SMTP server's account.
OBJECT-TYPE    
  OCTET STRING SIZE(0..60)  

brpsSMTPAUTHPassword 1.3.6.1.4.1.2435.2.4.3.1240.5.6.104
The password of SMTP server's account.
OBJECT-TYPE    
  OCTET STRING SIZE(0..32)  

brpsSMTPAUTHPasswordSet 1.3.6.1.4.1.2435.2.4.3.1240.5.6.105
Returns 1 if the SMTP server login password is set, 0 if not set.
OBJECT-TYPE    
  INTEGER 0..1  

brpsSmtpAUTHTimeout 1.3.6.1.4.1.2435.2.4.3.1240.5.6.106
The SMTP-AUTH timeout in seconds.
OBJECT-TYPE    
  INTEGER 10..32767  

brpsPOPbeforeSMTPWait 1.3.6.1.4.1.2435.2.4.3.1240.5.6.107
The wait time in mili seconds between POP logging in and SMTP sending.
OBJECT-TYPE    
  INTEGER 0..32767  

brpsAPOPEnable 1.3.6.1.4.1.2435.2.4.3.1240.5.6.108
0 indicates the APOP is not enabled. 1 indicates the APOP is enabled.
OBJECT-TYPE    
  INTEGER 0..1  

brpsSMTPEnhancedAuthSupported 1.3.6.1.4.1.2435.2.4.3.1240.5.6.150
Bit0 indicates 'no authentication'. Bit1 indicates 'SMTP-AUTH'. Bit2 indicates 'POP before SMTP'.
OBJECT-TYPE    
  INTEGER 0..7  

brpsAPOPSupported 1.3.6.1.4.1.2435.2.4.3.1240.5.6.151
0 indicates the APOP is not supported. 1 indicates the APOP is supported.
OBJECT-TYPE    
  INTEGER 0..1  

brpsEmailSendTestSupported 1.3.6.1.4.1.2435.2.4.3.1240.5.6.152
0 indicates the Email Sending Test is not supported. 1 indicates the Email Sending Test is supported.
OBJECT-TYPE    
  INTEGER 0..1  

brpsEmailRecvTestSupported 1.3.6.1.4.1.2435.2.4.3.1240.5.6.153
0 indicates the Email Receiving Test is not supported. 1 indicates the Email Receiving Test is supported.
OBJECT-TYPE    
  INTEGER 0..1  

brpsChangeSMTPPortSupported 1.3.6.1.4.1.2435.2.4.3.1240.5.6.154
0 indicates to change the SMTP port number is not supported. 1 indicates to change the SMTP port number is supported.
OBJECT-TYPE    
  INTEGER 0..1  

brpsSMTPPortNumber 1.3.6.1.4.1.2435.2.4.3.1240.5.6.155
The port number of connection to SMTP server.
OBJECT-TYPE    
  INTEGER 1..65535  

brpsChangePOP3PortSupported 1.3.6.1.4.1.2435.2.4.3.1240.5.6.156
0 indicates to change the POP3 port number is not supported. 1 indicates to change the POP3 port number is supported.
OBJECT-TYPE    
  INTEGER 0..1  

brpsPOP3PortNumber 1.3.6.1.4.1.2435.2.4.3.1240.5.6.157
The port number of connection to POP3 server.
OBJECT-TYPE    
  INTEGER 1..65535  

brpsTmpSMTPServerName 1.3.6.1.4.1.2435.2.4.3.1240.5.6.170
Temporary Setting for Email Sending Test. The FQDN name of the SMTP server.
OBJECT-TYPE    
  OCTET STRING SIZE(0..64)  

brpsTmpSMTPServerAuthMethod 1.3.6.1.4.1.2435.2.4.3.1240.5.6.171
Temporary Setting for Email Sending Test. 0 indicates the user is not authenticated to the SMTP Server. 1 indicates the user is authenticated to the SMTP Server using SMTP-AUTH. 2 indicates the user is authenticated to the SMTP Server using POP before SMTP.
OBJECT-TYPE    
  INTEGER 0..2  

brpsTmpSMTPAUTHUsername 1.3.6.1.4.1.2435.2.4.3.1240.5.6.172
Temporary Setting for Email Sending Test. The username of SMTP server's account.
OBJECT-TYPE    
  OCTET STRING SIZE(0..60)  

brpsTmpSMTPAUTHPassword 1.3.6.1.4.1.2435.2.4.3.1240.5.6.173
Temporary Setting for Email Sending Test. The password of SMTP server's account.
OBJECT-TYPE    
  OCTET STRING SIZE(0..32)  

brpsTmpPOP3ServerName 1.3.6.1.4.1.2435.2.4.3.1240.5.6.174
Temporary Setting for Email Sending/Receiving Test. The FQDN name of the POP3 server.
OBJECT-TYPE    
  OCTET STRING SIZE(0..64)  

brpsTmpPOP3Name 1.3.6.1.4.1.2435.2.4.3.1240.5.6.175
Temporary Setting for Email Sending/Receiving Test. The POP3 mailbox name.
OBJECT-TYPE    
  DisplayString  

brpsTmpPOP3Password 1.3.6.1.4.1.2435.2.4.3.1240.5.6.176
Temporary Setting for Email Sending/Receiving Test. The POP3 mailbox password.
OBJECT-TYPE    
  DisplayString  

brpsTmpPrintersEmailaddress 1.3.6.1.4.1.2435.2.4.3.1240.5.6.177
Temporary Setting for Email Sending Test. The Printers Email Address
OBJECT-TYPE    
  OCTET STRING  

brpsTmpAPOPEnable 1.3.6.1.4.1.2435.2.4.3.1240.5.6.178
Temporary Setting for Email Sending/Receiving Test. 0 indicates the APOP is not enabled. 1 indicates the APOP is enabled.
OBJECT-TYPE    
  INTEGER 0..1  

brpsTmpSMTPAUTHPasswordModified 1.3.6.1.4.1.2435.2.4.3.1240.5.6.179
0 indicates the SMTP server password is not modified. 1 indicates the SMTP server password is modified.
OBJECT-TYPE    
  INTEGER 0..1  

brpsTmpPOP3PasswordModified 1.3.6.1.4.1.2435.2.4.3.1240.5.6.180
0 indicates the POP3 server password is not modified. 1 indicates the POP3 server password is modified.
OBJECT-TYPE    
  INTEGER 0..1  

brpsTmpSMTPPortNumber 1.3.6.1.4.1.2435.2.4.3.1240.5.6.181
Temporary Setting for Email Sending Test. The port number of connection to SMTP server.
OBJECT-TYPE    
  INTEGER 1..65535  

brpsTmpPOP3PortNumber 1.3.6.1.4.1.2435.2.4.3.1240.5.6.182
Temporary Setting for Email Sending/Receiving Test. The port number of connection to POP3 server.
OBJECT-TYPE    
  INTEGER 1..65535  

brpsEmailSendTestMail 1.3.6.1.4.1.2435.2.4.3.1240.5.6.200
0 indicates the testmail is not sended at Email Sending Test. 1 indicates the testmail is sended at Email Sending Test.
OBJECT-TYPE    
  INTEGER 0..1  

brpsEmailTestDestinationAddress 1.3.6.1.4.1.2435.2.4.3.1240.5.6.201
The destination Email Address of Email Sending Test.
OBJECT-TYPE    
  DisplayString SIZE(0..80)  

brpsEmailSendTestCall 1.3.6.1.4.1.2435.2.4.3.1240.5.6.210
0 indicates the Email Sending Test is not called on. ('READY') 1 indicates the Email Sending Test is called on. ('START') 2 indicates the Email Sending Test is canceled. ('CANCEL')
OBJECT-TYPE    
  INTEGER 0..2  

brpsEmailRecvTestCall 1.3.6.1.4.1.2435.2.4.3.1240.5.6.211
0 indicates the Email Receiving Test is not called on. ('READY') 1 indicates the Email Receiving Test is called. ('START') 2 indicates the Email Receiving Test is canceled. ('CANCEL')
OBJECT-TYPE    
  INTEGER 0..2  

brpsEmailSendRecvTestCall 1.3.6.1.4.1.2435.2.4.3.1240.5.6.212
0 indicates the Email Sending and Receiving Test is not called on. ('READY') 1 indicates the Email Sending and Receiving Test is called. ('START') 2 indicates the Email Sending and Receiving Test is canceled. ('CANCEL')
OBJECT-TYPE    
  INTEGER 0..2  

brpsEmailTestResult 1.3.6.1.4.1.2435.2.4.3.1240.5.6.220
This Value is divided into 15-8bit and 7-0bit. 15-8bit indicates Email Sending Test's Result. 7-0bit indicates Email Receiving Test's Result. (However, the value from 0x00 to 0x04 is only set to 7-0bit.) 0x00 indicates the Email Test is not running. 0x01 indicates the Email Test is running. ('BUSY') 0x02 indicates the Email Test is canceled.('CANCELED') 0x03 indicates the Email Test is Locked by another Email Test process.(LOCKED) 0x04 indicates the Email Test is not executed. -- unused 0x10 indicates the Status 'Fatal Error is occurred during Email Testing'. 0x20 indicates the Status 'Invalid value is set in SMTP Server Address'. 0x21 indicates the Status 'Invalid value is set in SMTP-AUTH Account Name'. 0x22 indicates the Status 'Invalid value is set in SMTP-AUTH Password'. 0x30 indicates the Status 'Invalid value is set in POP3 Server Address'. 0x31 indicates the Status 'Invalid value is set in POP3 Account Name'. 0x32 indicates the Status 'Invalid value is set in POP3 Account Password'. 0x40 indicates the Status 'Invalid value is set in POP3 Printer E-mail Address'. 0x41 indicates the Status 'Invalid value is set in Destination E-mail Address'. 0x50 indicates the Status 'Sending OK'. 0x51 indicates the Status 'Cannot locate SMTP server'. 0x52 indicates the Status 'Cannot connect to SMTP server'. 0x53 indicates the Status 'Cannot authenticate with SMTP server by using method'. 0x54 indicates the Status 'Authentication failure in SMTP server'. 0x55 indicates the Status 'Email Sending Timeout' -- unused 0x60 indicates the Status 'Receiving OK'. 0x61 indicates the Status 'Cannot locate POP3 server'. 0x62 indicates the Status 'Cannot connect to POP3 server'. 0x63 indicates the Status 'Authentication failure in POP3 server'. 0x64 indicates the Status 'Cannot authenticate with POP3 server by using method'. 0x65 indicates the Status 'Email Receiving Timeout' -- unused 0x66 indicates the Email Test is Locked by another Email process. 0x70 indicates the Status 'Cannot resolve the host name (DNS Error)'.
OBJECT-TYPE    
  INTEGER 0..65535  

brpsPOP3TotalAPOPFailure 1.3.6.1.4.1.2435.2.4.3.1240.5.6.221
Counter of POP3 APOP error.
OBJECT-TYPE    
  INTEGER 0..65535  

brdlc 1.3.6.1.4.1.2435.2.4.3.1240.5.7
OBJECT IDENTIFIER    

brpsDLCSupported 1.3.6.1.4.1.2435.2.4.3.1240.5.7.1
0 indicates the DLC protocol is not supported. 1 indicates DLC support is implemented by the firmware
OBJECT-TYPE    
  INTEGER 0..1  

brpsDLCEnable 1.3.6.1.4.1.2435.2.4.3.1240.5.7.2
0 indicates the DLC protocol is not enabled. 1 indicates that the DLC protocol is enabled. Writing a non-zero value will enable the DLC protocol if is is supported by the firmware.
OBJECT-TYPE    
  INTEGER 0..1  

brpsDLCPrintStatus 1.3.6.1.4.1.2435.2.4.3.1240.5.7.3
DLC print status.
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

brpsDLCLLCState 1.3.6.1.4.1.2435.2.4.3.1240.5.7.4
LLC status.
OBJECT-TYPE    
  INTEGER 0..65535  

brpsDLCLLCConnectHost 1.3.6.1.4.1.2435.2.4.3.1240.5.7.5
LLC connected host name.
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

brpsDLCLLCLastIFrame 1.3.6.1.4.1.2435.2.4.3.1240.5.7.6
LLC last valid I-frame.
OBJECT-TYPE    
  INTEGER 0..65535  

brpsDLCLLCRecvPacket 1.3.6.1.4.1.2435.2.4.3.1240.5.7.7
Counter of LLC receive packets.
OBJECT-TYPE    
  INTEGER 0..65535  

brpsDLCLLCPortStatus 1.3.6.1.4.1.2435.2.4.3.1240.5.7.8
Port status.
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

brnetbeui 1.3.6.1.4.1.2435.2.4.3.1240.5.8
OBJECT IDENTIFIER    

brpsNetBEUISupported 1.3.6.1.4.1.2435.2.4.3.1240.5.8.1
0 indicates the NetBEUI protocol is not supported. 1 indicates NetBEUI support is implemented by the firmware
OBJECT-TYPE    
  INTEGER 0..1  

brpsNetBEUIEnable 1.3.6.1.4.1.2435.2.4.3.1240.5.8.2
0 indicates the NetBEUI protocol is not enabled. 1 indicates that the NetBEUI protocol is enabled. Writing a non-zero value will enable the NetBEUI protocol if is is supported by the firmware.
OBJECT-TYPE    
  INTEGER 0..1  

brpsNetBEUIDomain 1.3.6.1.4.1.2435.2.4.3.1240.5.8.3
The NetBEUI domain name.
OBJECT-TYPE    
  DisplayString SIZE(0..15)  

brpsNetBIOSIPSupported 1.3.6.1.4.1.2435.2.4.3.1240.5.8.4
0 indicates the NetBIOS IP protocol is not supported. 1 indicates NetBIOS IP support is implemented by the firmware
OBJECT-TYPE    
  INTEGER 0..1  

brpsNetBIOSIPEnable 1.3.6.1.4.1.2435.2.4.3.1240.5.8.5
0 indicates the NetBIOS IP protocol is not enabled. 1 indicates that the NetBIOS IP protocol is enabled. Writing a non-zero value will enable the NetBIOS IP protocol if is is supported by the firmware.
OBJECT-TYPE    
  INTEGER 0..1  

brpsNetBIOSIPMethod 1.3.6.1.4.1.2435.2.4.3.1240.5.8.6
Method used to determine the IP Address of the WINS server. AUTO tries all protocols (currently only DHCP is tried). STATIC uses the configured address.
OBJECT-TYPE    
  INTEGER 0..1  

brpsNetBIOSPrimaryWINSAddr 1.3.6.1.4.1.2435.2.4.3.1240.5.8.7
The IP Address of the primary WINS server.
OBJECT-TYPE    
  IpAddress  

brpsNetBIOSSecondaryWINSAddr 1.3.6.1.4.1.2435.2.4.3.1240.5.8.8
The IP Address of the secondary WINS server.
OBJECT-TYPE    
  IpAddress  

brpsNetBIOSPrintingSupported 1.3.6.1.4.1.2435.2.4.3.1240.5.8.101
0 indicates the NetBIOS IP protocol printing is not supported. 1 indicates the NetBIOS IP protocol printing is supported.
OBJECT-TYPE    
  INTEGER 0..1  

bripp 1.3.6.1.4.1.2435.2.4.3.1240.5.9
OBJECT IDENTIFIER    

brpsIPPSupported 1.3.6.1.4.1.2435.2.4.3.1240.5.9.1
0 indicates the IPP protocol is not supported. 1 indicates IPP support is implemented by the firmware
OBJECT-TYPE    
  INTEGER 0..1  

brpsIPPEnable 1.3.6.1.4.1.2435.2.4.3.1240.5.9.2
0 indicates the IPP protocol is not enabled. 1 indicates that the IPP protocol is enabled. Writing a non-zero value will enable the IPP protocol if it is supported by the firmware.
OBJECT-TYPE    
  INTEGER 0..1  

brIPPRegularPortEnable 1.3.6.1.4.1.2435.2.4.3.1240.5.9.3
0 indicates that the IPP regular port is not enabled. 1 indicates that the IPP regular port is enabled.
OBJECT-TYPE    
  INTEGER 0..1  

brIPPSSLPortEnable 1.3.6.1.4.1.2435.2.4.3.1240.5.9.4
0 indicates that the IPP SSL port is not enabled. 1 indicates that the IPP SSL port is enabled.
OBJECT-TYPE    
  INTEGER 0..1  

brIPPOriginalPortEnable 1.3.6.1.4.1.2435.2.4.3.1240.5.9.5
0 indicates that the IPP original port is not enableed. 1 indicates that the IPP original port is enabled.
OBJECT-TYPE    
  INTEGER 0..1  

brntsend 1.3.6.1.4.1.2435.2.4.3.1240.5.10
OBJECT IDENTIFIER    

brpsNtSendSupported 1.3.6.1.4.1.2435.2.4.3.1240.5.10.1
0 indicates the NtSend protocol is not supported. 1 indicates NtSend support is implemented by the firmware
OBJECT-TYPE    
  INTEGER 0..1  

brpsNtSendEnable 1.3.6.1.4.1.2435.2.4.3.1240.5.10.2
0 indicates the NtSend protocol is not enabled. 1 indicates that the NtSend protocol is enabled. Writing a non-zero value will enable the NtSend protocol if it is supported by the firmware.
OBJECT-TYPE    
  INTEGER 0..1  

brfirmware 1.3.6.1.4.1.2435.2.4.3.1240.6
OBJECT IDENTIFIER    

brpsFirmwareIPAddress 1.3.6.1.4.1.2435.2.4.3.1240.6.1
The IP address of the host from which to TFTP GET the firmware.
OBJECT-TYPE    
  IpAddress  

brpsFirmwareHost 1.3.6.1.4.1.2435.2.4.3.1240.6.2
The Netware server name from which to fetch the firmware.
OBJECT-TYPE    
  DisplayString  

brpsFirmwareFile 1.3.6.1.4.1.2435.2.4.3.1240.6.3
The firmware file to be reloaded.
OBJECT-TYPE    
  DisplayString  

brpsFirmwareReload 1.3.6.1.4.1.2435.2.4.3.1240.6.4
Setting a value of 0x5A will cause the print server to begin attempts to reload the firmware within 5 seconds. Further attempts to read or modify the configuration are not recommended until after the firmware has been reloaded.
OBJECT-TYPE    
  INTEGER 0..1  

brpsFirmwareDescription 1.3.6.1.4.1.2435.2.4.3.1240.6.5
Firmware version and date.
OBJECT-TYPE    
  DisplayString  

brpsFirmwareXModem 1.3.6.1.4.1.2435.2.4.3.1240.6.6
Set 1 execute XMODEM mode.
OBJECT-TYPE    
  INTEGER 0..1  

brpsFirmwareAdvancedAddressSupported 1.3.6.1.4.1.2435.2.4.3.1240.6.7
0 indicates the Firmware Advanced Address is not supported. 1 indicates Firmware Advanced Address support is implemented by the firmware
OBJECT-TYPE    
  INTEGER 0..1  

brpsFirmwareAdvancedAddress 1.3.6.1.4.1.2435.2.4.3.1240.6.8
The address of the host from which to TFTP GET the firmware.
OBJECT-TYPE    
  DisplayString SIZE(0..64)  

brnetConfigOpt 1.3.6.1.4.1.2435.2.4.3.2435
OBJECT IDENTIFIER    

broriginalprotocol 1.3.6.1.4.1.2435.2.4.3.2435.5
OBJECT IDENTIFIER    

broriginaltcpip 1.3.6.1.4.1.2435.2.4.3.2435.5.2
OBJECT IDENTIFIER    

brLPDType 1.3.6.1.4.1.2435.2.4.3.2435.5.2.1
OBJECT-TYPE    
  INTEGER 0..3  

broriginalftp 1.3.6.1.4.1.2435.2.4.3.2435.5.10
OBJECT IDENTIFIER    

brFTPSupported 1.3.6.1.4.1.2435.2.4.3.2435.5.10.1
0 indicates the FTP protocol is not supported. 1 indicates FTP support is implemented by the firmware
OBJECT-TYPE    
  INTEGER 0..1  

brFTPEnable 1.3.6.1.4.1.2435.2.4.3.2435.5.10.2
0 indicates the FTP protocol is not enabled. 1 indicates that the FTP protocol is enabled. Writing a non-zero value will enable the FTP protocol if it is supported by the firmware.
OBJECT-TYPE    
  INTEGER 0..1  

broriginalupnp 1.3.6.1.4.1.2435.2.4.3.2435.5.11
OBJECT IDENTIFIER    

brUPnPSupported 1.3.6.1.4.1.2435.2.4.3.2435.5.11.1
0 indicates the UPnP protocol is not supported. 1 indicates UPnP support is implemented by the firmware
OBJECT-TYPE    
  INTEGER 0..1  

brUPnPEnable 1.3.6.1.4.1.2435.2.4.3.2435.5.11.2
0 indicates the UPnP protocol is not enabled. 1 indicates that the UPnP protocol is enabled. Writing a non-zero value will enable the UPnP protocol if it is supported by the firmware.
OBJECT-TYPE    
  INTEGER 0..1  

broriginalapipa 1.3.6.1.4.1.2435.2.4.3.2435.5.12
OBJECT IDENTIFIER    

brAPIPASupported 1.3.6.1.4.1.2435.2.4.3.2435.5.12.1
0 indicates the APIPA protocol is not supported. 1 indicates APIPA support is implemented by the firmware
OBJECT-TYPE    
  INTEGER 0..1  

brAPIPAEnable 1.3.6.1.4.1.2435.2.4.3.2435.5.12.2
0 indicates the APIPA protocol is not enabled. 1 indicates that the APIPA protocol is enabled. Writing a non-zero value will enable the APIPA protocol if it is supported by the firmware.
OBJECT-TYPE    
  INTEGER 0..1  

broriginalmdns 1.3.6.1.4.1.2435.2.4.3.2435.5.13
OBJECT IDENTIFIER    

brmDNSSupported 1.3.6.1.4.1.2435.2.4.3.2435.5.13.1
0 indicates the mDNS protocol is not supported. 1 indicates mDNS support is implemented by the firmware
OBJECT-TYPE    
  INTEGER 0..1  

brmDNSEnable 1.3.6.1.4.1.2435.2.4.3.2435.5.13.2
0 indicates the mDNS protocol is not enabled. 1 indicates that the mDNS protocol is enabled. Writing a non-zero value will enable the mDNS protocol if it is supported by the firmware.
OBJECT-TYPE    
  INTEGER 0..1  

brmDNSPrinterName 1.3.6.1.4.1.2435.2.4.3.2435.5.13.3
mDNS Service Name
OBJECT-TYPE    
  DisplayString SIZE(0..64)  

broriginalLAA 1.3.6.1.4.1.2435.2.4.3.2435.5.14
OBJECT IDENTIFIER    

brLAASupported 1.3.6.1.4.1.2435.2.4.3.2435.5.14.1
This value indicate if the locally administered addressing is supported. 0: Not Supported 1: Supported
OBJECT-TYPE    
  INTEGER 0..1  

brLAAMacAddress 1.3.6.1.4.1.2435.2.4.3.2435.5.14.2
A locally administered address (LAA) that replaces the factory-assigned MAC address (UAA: universally administered address). If this setting is all-zero address (i.e. 6 bytes of zeros), the factory-assigned MAC address is used as the MAC address of the device. The LAA address must start with X2, X6, XA, or XE, where X is any hexadecimal digit 0 to F.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

broriginalIPv6 1.3.6.1.4.1.2435.2.4.3.2435.5.15
OBJECT IDENTIFIER    

brIPv6Supported 1.3.6.1.4.1.2435.2.4.3.2435.5.15.1
0 indicates the IPv6 protocol is not supported. 1 indicates IPv6 support is implemented by the firmware
OBJECT-TYPE    
  INTEGER 0..1  

brIPv6Enable 1.3.6.1.4.1.2435.2.4.3.2435.5.15.2
0 indicates the IPv6 protocol is not enabled. 1 indicates that the IPv6 protocol is enabled. Writing a non-zero value will enable the IPv6 protocol if it is supported by the firmware.
OBJECT-TYPE    
  INTEGER 0..1  

brIPv6Priority 1.3.6.1.4.1.2435.2.4.3.2435.5.15.3
0 indicates the IPv6 protocol is low priority. 1 indicates that the IPv6 protocol is high priority.
OBJECT-TYPE    
  INTEGER 0..1  

broriginaltelnet 1.3.6.1.4.1.2435.2.4.3.2435.5.16
OBJECT IDENTIFIER    

brtelnetSupported 1.3.6.1.4.1.2435.2.4.3.2435.5.16.1
0 indicates the telnet protocol is not supported. 1 indicates telnet support is implemented by the firmware
OBJECT-TYPE    
  INTEGER 0..1  

brtelnetEnable 1.3.6.1.4.1.2435.2.4.3.2435.5.16.2
0 indicates the telnet protocol is not enabled. 1 indicates that the telnet protocol is enabled. Writing a non-zero value will enable the telnet protocol if it is supported by the firmware.
OBJECT-TYPE    
  INTEGER 0..1  

broriginalEWS 1.3.6.1.4.1.2435.2.4.3.2435.5.17
OBJECT IDENTIFIER    

brEWSSupported 1.3.6.1.4.1.2435.2.4.3.2435.5.17.1
0 indicates the EWS protocol is not supported. 1 indicates EWS support is implemented by the firmware
OBJECT-TYPE    
  INTEGER 0..1  

brEWSEnable 1.3.6.1.4.1.2435.2.4.3.2435.5.17.2
0 indicates the EWS protocol is not enabled. 1 indicates that the EWS protocol is enabled. Writing a non-zero value will enable the EWS protocol if it is supported by the firmware.
OBJECT-TYPE    
  INTEGER 0..1  

brEWSRegularPortEnable 1.3.6.1.4.1.2435.2.4.3.2435.5.17.3
0 indicates that the EWS regular port is not enabled. 1 indicates that the EWS regular port is enabled.
OBJECT-TYPE    
  INTEGER 0..1  

brEWSSSLPortEnable 1.3.6.1.4.1.2435.2.4.3.2435.5.17.4
0 indicates that the EWS SSL port is not enabled. 1 indicates that the EWS SSL port is enabled.
OBJECT-TYPE    
  INTEGER 0..1  

broriginalSNMP 1.3.6.1.4.1.2435.2.4.3.2435.5.18
OBJECT IDENTIFIER    

brSNMPSupported 1.3.6.1.4.1.2435.2.4.3.2435.5.18.1
0 indicates the SNMP protocol is not supported. 1 indicates SNMP support is implemented by the firmware
OBJECT-TYPE    
  INTEGER 0..1  

brSNMPEnable 1.3.6.1.4.1.2435.2.4.3.2435.5.18.2
0 indicates the SNMP protocol is not enabled. 1 indicates that the SNMP protocol is enabled. Writing a non-zero value will enable the SNMP protocol if it is supported by the firmware.
OBJECT-TYPE    
  INTEGER 0..1  

brSNMPV3Supported 1.3.6.1.4.1.2435.2.4.3.2435.5.18.10
0 indicates SNMPv3 is not supported. 1 indicates SNMPv3 is supported.
OBJECT-TYPE    
  INTEGER 0..1  

brSNMPCommMode 1.3.6.1.4.1.2435.2.4.3.2435.5.18.11
1 indicates v1/v2c read-write access is enable. 2 indicates v3 read-write access is enable. 3 indicates v1/v2c read-only access and v3 read-write access is enable.
OBJECT-TYPE    
  INTEGER 1..3  

brSNMPV3UserName 1.3.6.1.4.1.2435.2.4.3.2435.5.18.12
The username of SNMPv3.
OBJECT-TYPE    
  DisplayString SIZE(1..32)  

brSNMPV3KeyType 1.3.6.1.4.1.2435.2.4.3.2435.5.18.13
1 indicates that the key type of SNMPv3 is ASCII. 2 indicates that the key type of SNMPv3 is HEX
OBJECT-TYPE    
  INTEGER 1..2  

brSNMPV3AuthKey 1.3.6.1.4.1.2435.2.4.3.2435.5.18.14
The authentication key of SNMPv3.
OBJECT-TYPE    
  OCTET STRING SIZE(0..16)  

brSNMPV3AuthPassword 1.3.6.1.4.1.2435.2.4.3.2435.5.18.15
The authentication password of SNMPv3.
OBJECT-TYPE    
  DisplayString SIZE(1..16)  

brSNMPV3PrivKey 1.3.6.1.4.1.2435.2.4.3.2435.5.18.16
The privacy key of SNMPv3.
OBJECT-TYPE    
  OCTET STRING SIZE(0..16)  

brSNMPV3PrivPassword 1.3.6.1.4.1.2435.2.4.3.2435.5.18.17
The privacy password of SNMPv3.
OBJECT-TYPE    
  DisplayString SIZE(1..16)  

brSNMPV3ContextName 1.3.6.1.4.1.2435.2.4.3.2435.5.18.18
The contextname of SNMPv3.
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

broriginalldap 1.3.6.1.4.1.2435.2.4.3.2435.5.19
OBJECT IDENTIFIER    

brLdapSupported 1.3.6.1.4.1.2435.2.4.3.2435.5.19.1
0 indicates the LDAP client is not supported. 1 indicates the LDAP client is implemented by the firmware
OBJECT-TYPE    
  INTEGER 0..1  

brLdapEnable 1.3.6.1.4.1.2435.2.4.3.2435.5.19.2
0 indicates the LDAP client is not enabled. 1 indicates that the LDAP client is enabled. Writing a non-zero value will enable the Ldap if it is supported by the firmware.
OBJECT-TYPE    
  INTEGER 0..1  

brLdapTimeout 1.3.6.1.4.1.2435.2.4.3.2435.5.19.3
timeout value (sec) for LDAP server.
OBJECT-TYPE    
  INTEGER 1..32767  

brLdapTimeoutSupported 1.3.6.1.4.1.2435.2.4.3.2435.5.19.4
0 indicates the LDAP timeout is not supported. 1 indicates the LDAP timeout is implemented by the firmware
OBJECT-TYPE    
  INTEGER 0..1  

brLdapServerCount 1.3.6.1.4.1.2435.2.4.3.2435.5.19.11
Maximum number of LDAP Server INDEX.
OBJECT-TYPE    
  INTEGER  

brLdapServerInfoTable 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12
This table represents LDAP Server Info.
OBJECT-TYPE    
  SEQUENCE OF  
    BrLdapServerInfoEntry

brLdapServerInfoEntry 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12.1
A row in the LdapServerInfo table. Rows cannot be created or deleted.
OBJECT-TYPE    
  BrLdapServerInfoEntry  

brLdapServerInfoIndex 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12.1.1
The number.
OBJECT-TYPE    
  INTEGER 0..1  

brLdapServerName 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12.1.2
The LDAP server name.
OBJECT-TYPE    
  DisplayString SIZE(0..64)  

brLdapServerPort 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12.1.3
The LDAP server port number.
OBJECT-TYPE    
  INTEGER 0..65535  

brLdapServerAuth 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12.1.4
The LDAP server authentication method.
OBJECT-TYPE    
  INTEGER anonymous(1), simple(2), kerberos(3)  

brLdapServerUserDN 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12.1.5
The LDAP server user DN.
OBJECT-TYPE    
  OCTET STRING SIZE(0..255)  

brLdapServerPassword 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12.1.6
The LDAP server password.
OBJECT-TYPE    
  OCTET STRING SIZE(0..32)  

brLdapServerPasswordSet 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12.1.7
Returns 1 if the LDAP server password is set, 0 if not set.
OBJECT-TYPE    
  INTEGER 0..1  

brLdapServerBaseDN 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12.1.8
The LDAP server base DN.
OBJECT-TYPE    
  OCTET STRING SIZE(0..255)  

brLdapServerAttrEMail 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12.1.10
The LDAP server attribute or e-mail.
OBJECT-TYPE    
  DisplayString SIZE(0..64)  

brLdapServerAttrFAXNumber 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12.1.11
The LDAP server attribute or facsimile telephone number.
OBJECT-TYPE    
  DisplayString SIZE(0..64)  

brLdapServerAttrDetail1 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12.1.12
The LDAP server attribute or detail 1.
OBJECT-TYPE    
  DisplayString SIZE(0..64)  

brLdapServerAttrDetail2 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12.1.13
The LDAP server attribute or detail 2.
OBJECT-TYPE    
  DisplayString SIZE(0..64)  

brLdapServerAttrDetail3 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12.1.14
The LDAP server attribute or detail 3.
OBJECT-TYPE    
  DisplayString SIZE(0..64)  

brLdapServerAttrDetail4 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12.1.15
The LDAP server attribute or detail 4.
OBJECT-TYPE    
  DisplayString SIZE(0..64)  

brLdapServerAttrDetailEnable1 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12.1.16
Enable flag of the LDAP server attribute of detail 1.
OBJECT-TYPE    
  INTEGER 0..1  

brLdapServerAttrDetailEnable2 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12.1.17
Enable flag of the LDAP server attribute of detail 2.
OBJECT-TYPE    
  INTEGER 0..1  

brLdapServerAttrDetailEnable3 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12.1.18
Enable flag of the LDAP server attribute of detail 3.
OBJECT-TYPE    
  INTEGER 0..1  

brLdapServerAttrDetailEnable4 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12.1.19
Enable flag of the LDAP server attribute of detail 4.
OBJECT-TYPE    
  INTEGER 0..1  

brLdapKerberosServerName 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12.1.20
The Kerberos server name for LDAP.
OBJECT-TYPE    
  DisplayString SIZE(0..64)  

brLdapKerberosServerPort 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12.1.21
The Kerberos server port number for LDAP.
OBJECT-TYPE    
  INTEGER 0..65535  

brLdapServerAttrNameCount 1.3.6.1.4.1.2435.2.4.3.2435.5.19.21
Maximum number of LDAP Server Attribute of name INDEX.
OBJECT-TYPE    
  INTEGER  

brLdapServerAttrNameTable 1.3.6.1.4.1.2435.2.4.3.2435.5.19.22
This table represents LDAP Server Attribute of name.
OBJECT-TYPE    
  SEQUENCE OF  
    BrLdapServerAttrNameEntry

brLdapServerAttrNameEntry 1.3.6.1.4.1.2435.2.4.3.2435.5.19.22.1
A row in the LdapServerAttributeName table. Rows cannot be created or deleted.
OBJECT-TYPE    
  BrLdapServerAttrNameEntry  

brLdapServerAttrNameIndex 1.3.6.1.4.1.2435.2.4.3.2435.5.19.22.1.1
The number.
OBJECT-TYPE    
  INTEGER 0..4  

brLdapServerAttrName 1.3.6.1.4.1.2435.2.4.3.2435.5.19.22.1.2
The LDAP server attribute of name.
OBJECT-TYPE    
  DisplayString SIZE(0..64)  

brLdapSetDefault 1.3.6.1.4.1.2435.2.4.3.2435.5.19.99
Setting the value resets all LDAP parameters to their factory default value.
OBJECT-TYPE    
  INTEGER 0..32767  

broriginalTFTP 1.3.6.1.4.1.2435.2.4.3.2435.5.20
OBJECT IDENTIFIER    

brTFTPSupported 1.3.6.1.4.1.2435.2.4.3.2435.5.20.1
0 indicates the TFTP protocol is not supported. 1 indicates TFTP support is implemented by the firmware
OBJECT-TYPE    
  INTEGER 0..1  

brTFTPEnable 1.3.6.1.4.1.2435.2.4.3.2435.5.20.2
0 indicates the TFTP protocol is not enabled. 1 indicates that the TFTP protocol is enabled. Writing a non-zero value will enable the TFTP protocol if it is supported by the firmware.
OBJECT-TYPE    
  INTEGER 0..1  

broriginalHTTPS 1.3.6.1.4.1.2435.2.4.3.2435.5.21
OBJECT IDENTIFIER    

brHTTPSSupported 1.3.6.1.4.1.2435.2.4.3.2435.5.21.1
0 indicates the HTTPS/IPPS protocol is not supported. 1 indicates HTTPS/IPPS support is implemented by the firmware
OBJECT-TYPE    
  INTEGER 0..1  

brHTTPSEnable 1.3.6.1.4.1.2435.2.4.3.2435.5.21.2
0 indicates the HTTPS/IPPS protocol is not enabled. 1 indicates that the HTTPS/IPPS protocol is enabled. Writing a non-zero value will enable the HTTPS/IPPS protocol if it is supported by the firmware.
OBJECT-TYPE    
  INTEGER 0..1  

broriginalLPD 1.3.6.1.4.1.2435.2.4.3.2435.5.22
OBJECT IDENTIFIER    

brLPDSupported 1.3.6.1.4.1.2435.2.4.3.2435.5.22.1
0 indicates the LPD protocol is not supported. 1 indicates LPD support is implemented by the firmware
OBJECT-TYPE    
  INTEGER 0..1  

brLPDEnable 1.3.6.1.4.1.2435.2.4.3.2435.5.22.2
0 indicates the LPD protocol is not enabled. 1 indicates that the LPD protocol is enabled. Writing a non-zero value will enable the LPD protocol if it is supported by the firmware.
OBJECT-TYPE    
  INTEGER 0..1  

broriginalRawPort 1.3.6.1.4.1.2435.2.4.3.2435.5.23
OBJECT IDENTIFIER    

brRawPortSupported 1.3.6.1.4.1.2435.2.4.3.2435.5.23.1
0 indicates the RawPort protocol is not supported. 1 indicates RawPort support is implemented by the firmware
OBJECT-TYPE    
  INTEGER 0..1  

brRawPortEnable 1.3.6.1.4.1.2435.2.4.3.2435.5.23.2
0 indicates the RawPort protocol is not enabled. 1 indicates that the RawPort protocol is enabled. Writing a non-zero value will enable the RawPort protocol if it is supported by the firmware.
OBJECT-TYPE    
  INTEGER 0..1  

broriginalLLTD 1.3.6.1.4.1.2435.2.4.3.2435.5.24
OBJECT IDENTIFIER    

brLLTDSupported 1.3.6.1.4.1.2435.2.4.3.2435.5.24.1
0 indicates the LLTD protocol is not supported. 1 indicates LLTD support is implemented by the firmware
OBJECT-TYPE    
  INTEGER 0..1  

brLLTDEnable 1.3.6.1.4.1.2435.2.4.3.2435.5.24.2
0 indicates the LLTD protocol is not enabled. 1 indicates that the LLTD protocol is enabled. Writing a non-zero value will enable the LLTD protocol if it is supported by the firmware.
OBJECT-TYPE    
  INTEGER 0..1  

broriginalWebServices 1.3.6.1.4.1.2435.2.4.3.2435.5.25
OBJECT IDENTIFIER    

brWebServicesSupported 1.3.6.1.4.1.2435.2.4.3.2435.5.25.1
0 indicates the WebServices protocol is not supported. 1 indicates WebServices support is implemented by the firmware
OBJECT-TYPE    
  INTEGER 0..1  

brWebServicesEnable 1.3.6.1.4.1.2435.2.4.3.2435.5.25.2
0 indicates the WebServices protocol is not enabled. 1 indicates that the WebServices protocol is enabled. Writing a non-zero value will enable the WebServices protocol if it is supported by the firmware.
OBJECT-TYPE    
  INTEGER 0..1  

brWebServicesRegularPortEnable 1.3.6.1.4.1.2435.2.4.3.2435.5.25.3
0 indicates that the WebServices regular port is not enabled. 1 indicates that the WebServices regular port is enabled.
OBJECT-TYPE    
  INTEGER 0..1  

brWebServicesSSLPortEnable 1.3.6.1.4.1.2435.2.4.3.2435.5.25.4
0 indicates that the WebServices SSL port is not enabled. 1 indicates that the WebServices SSL port is enabled.
OBJECT-TYPE    
  INTEGER 0..1  

broriginalLLMNR 1.3.6.1.4.1.2435.2.4.3.2435.5.26
OBJECT IDENTIFIER    

brLLMNREnable 1.3.6.1.4.1.2435.2.4.3.2435.5.26.1
0 indicates the LLMNR protocol is not enabled. 1 indicates that the LLMNR protocol is enabled.
OBJECT-TYPE    
  INTEGER 0..1  

broriginalKerberos 1.3.6.1.4.1.2435.2.4.3.2435.5.27
OBJECT IDENTIFIER    

brKerberosSupported 1.3.6.1.4.1.2435.2.4.3.2435.5.27.1
0 indicates the Kerberos protocol is not supported. 1 indicates Kerberos support is implemented by the firmware
OBJECT-TYPE    
  INTEGER 0..1  

broriginalCIFS 1.3.6.1.4.1.2435.2.4.3.2435.5.28
OBJECT IDENTIFIER    

brCIFSSupported 1.3.6.1.4.1.2435.2.4.3.2435.5.28.1
0 indicates the CIFS protocol is not supported. 1 indicates CIFS support is implemented by the firmware
OBJECT-TYPE    
  INTEGER 0..1  

brCIFSEnable 1.3.6.1.4.1.2435.2.4.3.2435.5.28.2
0 indicates the CIFS protocol is not enabled. 1 indicates that the CIFS protocol is enabled. Writing a non-zero value will enable the CIFS protocol if it is supported by the firmware.
OBJECT-TYPE    
  INTEGER 0..1  

broriginalSNTP 1.3.6.1.4.1.2435.2.4.3.2435.5.29
OBJECT IDENTIFIER    

brSNTPCSupported 1.3.6.1.4.1.2435.2.4.3.2435.5.29.1
0 indicates the SNTP is not supported. 1 indicates SNTP is supported.
OBJECT-TYPE    
  INTEGER 0..1  

brSNTPCEnable 1.3.6.1.4.1.2435.2.4.3.2435.5.29.2
0 indicates the SNTP is not disabled. 1 indicates that the SNTP is enabled.
OBJECT-TYPE    
  INTEGER 0..1  

brSNTPCServerMethod 1.3.6.1.4.1.2435.2.4.3.2435.5.29.3
1 indicates SNTP Server Method is AUTO. 2 indicates SNTP Server Method is STATIC. 3 indicates SNTP Server Method is PRESET.
OBJECT-TYPE    
  INTEGER 1..3  

brSNTPCSyncMethod 1.3.6.1.4.1.2435.2.4.3.2435.5.29.4
1 indicates Synchronous Method is AUTO. 2 indicates Synchronous Method is STATIC.
OBJECT-TYPE    
  INTEGER 1..2  

brSNTPCIntervalMin 1.3.6.1.4.1.2435.2.4.3.2435.5.29.5
The minimum value of synchronous interval.
OBJECT-TYPE    
  INTEGER 1..168  

brSNTPCInterval 1.3.6.1.4.1.2435.2.4.3.2435.5.29.6
The synchronous interval is used for synchronous method INTERVAL.
OBJECT-TYPE    
  INTEGER 1..168  

brSNTPCSyncResult 1.3.6.1.4.1.2435.2.4.3.2435.5.29.7
The result of the last checking time. 1: Success 2: Synchronizing 3: Failed 4: Not yet checking
OBJECT-TYPE    
  INTEGER 1..4  

brSNTPCPrimaryServerName 1.3.6.1.4.1.2435.2.4.3.2435.5.29.8
The primary server name of SNTP.
OBJECT-TYPE    
  DisplayString SIZE(0..64)  

brSNTPCPrimaryServerPort 1.3.6.1.4.1.2435.2.4.3.2435.5.29.9
The port number of primary SNTP server.
OBJECT-TYPE    
  INTEGER 1..65535  

brSNTPCSecondaryServerName 1.3.6.1.4.1.2435.2.4.3.2435.5.29.10
The secondary server name of SNTP.
OBJECT-TYPE    
  DisplayString SIZE(0..64)  

brSNTPCSecondaryServerPort 1.3.6.1.4.1.2435.2.4.3.2435.5.29.11
The port number of secondary SNTP server.
OBJECT-TYPE    
  INTEGER 1..65535  

broriginalSecurity 1.3.6.1.4.1.2435.2.4.3.2435.5.100
OBJECT IDENTIFIER    

brSecurityGeneralStatus 1.3.6.1.4.1.2435.2.4.3.2435.5.100.1
OBJECT IDENTIFIER    

brDeviceNegotiationEncryptVer 1.3.6.1.4.1.2435.2.4.3.2435.5.100.1.1
OBJECT-TYPE    
  INTEGER 0..1  

brpsServerCertificateNum 1.3.6.1.4.1.2435.2.4.3.2435.5.100.1.2
OBJECT-TYPE    
  INTEGER  

brSecurityGeneralSetup 1.3.6.1.4.1.2435.2.4.3.2435.5.100.2
OBJECT IDENTIFIER    

brSecurityDeviceNegotiation 1.3.6.1.4.1.2435.2.4.3.2435.5.100.10
OBJECT IDENTIFIER    

brDeviceNegotiationGetChallenge 1.3.6.1.4.1.2435.2.4.3.2435.5.100.10.1
OBJECT-TYPE    
  OCTET STRING SIZE(20)  

brDeviceNegotiationConfirmPassword 1.3.6.1.4.1.2435.2.4.3.2435.5.100.10.2
OBJECT-TYPE    
  OCTET STRING SIZE(60)  

brDeviceNegotiationChangePassword 1.3.6.1.4.1.2435.2.4.3.2435.5.100.10.3
OBJECT-TYPE    
  OCTET STRING SIZE(48)  

broriginalinternetsetting 1.3.6.1.4.1.2435.2.4.3.2435.10
OBJECT IDENTIFIER    

broriginalproxy 1.3.6.1.4.1.2435.2.4.3.2435.10.1
OBJECT IDENTIFIER    

brProxySupported 1.3.6.1.4.1.2435.2.4.3.2435.10.1.1
0 indicates the Proxy is not supported. 1 indicates Proxy is implemented by the firmware
OBJECT-TYPE    
  INTEGER 0..1  

brProxyEnable 1.3.6.1.4.1.2435.2.4.3.2435.10.1.2
0 indicates the Proxy is not enabled. 1 indicates that the Proxy is enabled. Writing a non-zero value will enable the Proxy if it is supported by the firmware.
OBJECT-TYPE    
  INTEGER 0..1  

brProxyBypassServer 1.3.6.1.4.1.2435.2.4.3.2435.10.1.3
on(2) indicates the bypass proxy server for local addresses.
OBJECT-TYPE    
  INTEGER off(1), on(2)  

brProxyServerCount 1.3.6.1.4.1.2435.2.4.3.2435.10.1.11
Maximum number of Proxy Server INDEX.
OBJECT-TYPE    
  INTEGER  

brProxyServerInfoTable 1.3.6.1.4.1.2435.2.4.3.2435.10.1.12
This table represents Proxy Server Info.
OBJECT-TYPE    
  SEQUENCE OF  
    BrProxyServerInfoEntry

brProxyServerInfoEntry 1.3.6.1.4.1.2435.2.4.3.2435.10.1.12.1
A row in the ProxyServerInfo table. Rows cannot be created or deleted.
OBJECT-TYPE    
  BrProxyServerInfoEntry  

brProxyServerInfoIndex 1.3.6.1.4.1.2435.2.4.3.2435.10.1.12.1.1
The number.
OBJECT-TYPE    
  INTEGER 1..16  

brProxyServerType 1.3.6.1.4.1.2435.2.4.3.2435.10.1.12.1.2
The Proxy server ID.
OBJECT-TYPE    
  INTEGER http(1), secure(2), ftp(3), gopher(4), socks(5)  

brProxyServerName 1.3.6.1.4.1.2435.2.4.3.2435.10.1.12.1.3
The Proxy server name.
OBJECT-TYPE    
  OCTET STRING SIZE(0..80)  

brProxyServerPort 1.3.6.1.4.1.2435.2.4.3.2435.10.1.12.1.4
The Proxy server port number.
OBJECT-TYPE    
  INTEGER 0..65535  

broriginalOtherSetting 1.3.6.1.4.1.2435.2.4.3.2435.20
OBJECT IDENTIFIER    

broriginalJobTermination 1.3.6.1.4.1.2435.2.4.3.2435.20.1
OBJECT IDENTIFIER    

brJobTerminationSupported 1.3.6.1.4.1.2435.2.4.3.2435.20.1.1
0 indicates the Job termination setting is not supported. 1 indicates the Job termination setting is implemented by the firmware
OBJECT-TYPE    
  INTEGER 0..1  

brJobTerminationEnable 1.3.6.1.4.1.2435.2.4.3.2435.20.1.2
0 indicates the Job termination setting is not enabled. 1 indicates the Job termination setting is enabled.
OBJECT-TYPE    
  INTEGER 0..1  

broriginalSNMPTrap 1.3.6.1.4.1.2435.2.4.3.2435.20.2
OBJECT IDENTIFIER    

brSNMPTrapTable 1.3.6.1.4.1.2435.2.4.3.2435.20.2.1
OBJECT-TYPE    
  SEQUENCE OF  
    BrSNMPTrapEntry

brSNMPTrapEntry 1.3.6.1.4.1.2435.2.4.3.2435.20.2.1.1
OBJECT-TYPE    
  BrSNMPTrapEntry  

brSNMPTrapIndex 1.3.6.1.4.1.2435.2.4.3.2435.20.2.1.1.1
The number.
OBJECT-TYPE    
  INTEGER 1..16  

brTCPIPServerAddress 1.3.6.1.4.1.2435.2.4.3.2435.20.2.1.1.2
The Destination IP Address for SNMP Trap.
OBJECT-TYPE    
  IpAddress  

broriginalLegacy 1.3.6.1.4.1.2435.2.4.3.2435.20.3
OBJECT IDENTIFIER    

brLegacyCompatible 1.3.6.1.4.1.2435.2.4.3.2435.20.3.1
OBJECT-TYPE    
  INTEGER  

npMultiCards 1.3.6.1.4.1.2435.2.4.4
OBJECT IDENTIFIER    

npMultiIFSet 1.3.6.1.4.1.2435.2.4.4.99
OBJECT IDENTIFIER    

brMultiIFdns 1.3.6.1.4.1.2435.2.4.4.99.1
OBJECT IDENTIFIER    

brMultiIFDNSTable 1.3.6.1.4.1.2435.2.4.4.99.1.1
OBJECT-TYPE    
  SEQUENCE OF  
    BrMultiIFDNSEntry

brMultiIFDNSEntry 1.3.6.1.4.1.2435.2.4.4.99.1.1.1
OBJECT-TYPE    
  BrMultiIFDNSEntry  

brMultiIFTCPIPDNSIPSetup 1.3.6.1.4.1.2435.2.4.4.99.1.1.1.1
DNS mode 1:static 2:auto
OBJECT-TYPE    
  INTEGER static(1), auto(2)  

brMultiIFPrimaryDNSIPAddress 1.3.6.1.4.1.2435.2.4.4.99.1.1.1.2
Primary DNS IP Address
OBJECT-TYPE    
  IpAddress  

brMultiIFSecondaryDNSIPAddress 1.3.6.1.4.1.2435.2.4.4.99.1.1.1.3
Secondary DNS IP Address
OBJECT-TYPE    
  IpAddress  

brMultiIFTCPIPConnectTime 1.3.6.1.4.1.2435.2.4.4.99.1.1.1.4
TCP/IP connect time.
OBJECT-TYPE    
  INTEGER  

brnetMultiIFConfig 1.3.6.1.4.1.2435.2.4.4.1240
OBJECT IDENTIFIER    

brMultiIFconfig 1.3.6.1.4.1.2435.2.4.4.1240.1
OBJECT IDENTIFIER    

brMultiIFSupported 1.3.6.1.4.1.2435.2.4.4.1240.1.1
0 indicates the Multi Interface is not supported. 1 indicates Multi Interface is supported.
OBJECT-TYPE    
  INTEGER 0..1  

brMultiIFActiveIF 1.3.6.1.4.1.2435.2.4.4.1240.1.2
1 LAN 2 Wireless LAN 3 Both
OBJECT-TYPE    
  INTEGER lan(1), wirelesslan(2), both(3)  

brMultiIFAllSetDefault 1.3.6.1.4.1.2435.2.4.4.1240.1.3
Setting the value resets all parameters to their factory default value.
OBJECT-TYPE    
  INTEGER 0..32767  

brMultiIFCount 1.3.6.1.4.1.2435.2.4.4.1240.1.4
MultiIF Count
OBJECT-TYPE    
  INTEGER  

brMultiIFConfigureTable 1.3.6.1.4.1.2435.2.4.4.1240.1.5
OBJECT-TYPE    
  SEQUENCE OF  
    BrMultiIFConfigureEntry

brMultiIFConfigureEntry 1.3.6.1.4.1.2435.2.4.4.1240.1.5.1
OBJECT-TYPE    
  BrMultiIFConfigureEntry  

brMultiIFConfigureIndex 1.3.6.1.4.1.2435.2.4.4.1240.1.5.1.1
The number.
OBJECT-TYPE    
  INTEGER 1..4  

brMultiIFType 1.3.6.1.4.1.2435.2.4.4.1240.1.5.1.2
Interface Type
OBJECT-TYPE    
  INTEGER lan(1), wirelesslan(2)  

brMultiIFDescription 1.3.6.1.4.1.2435.2.4.4.1240.1.5.1.3
Interface Description
OBJECT-TYPE    
  DisplayString SIZE(0..64)  

brMultiIFNodeName 1.3.6.1.4.1.2435.2.4.4.1240.1.5.1.4
An administratively-assigned name for this managed node. By convention, this is the node's fully-qualified domain name.
OBJECT-TYPE    
  OCTET STRING  

brMultiIFInterfaceEnable 1.3.6.1.4.1.2435.2.4.4.1240.1.5.1.5
0 indicates the Interfase is not enabled. 1 indicates the Interfase is enabled.
OBJECT-TYPE    
  INTEGER 0..1  

brMultiIFEnetMode 1.3.6.1.4.1.2435.2.4.4.1240.1.5.1.6
Ethernet type.
OBJECT-TYPE    
  INTEGER 0..4  

brMultiIFHardwareType 1.3.6.1.4.1.2435.2.4.4.1240.1.5.1.7
Hardware type of the print server.
OBJECT-TYPE    
  INTEGER 0..32767  

brMultiIFNodeType 1.3.6.1.4.1.2435.2.4.4.1240.1.5.1.8
A textual description of the entity. This value should include the full name and version identification of the system's hardware type, software operating-system, and networking software. It is mandatory that this only contain printable ASCII characters.
OBJECT-TYPE    
  OCTET STRING  

brMultiIFInterfaceEnableImmediate 1.3.6.1.4.1.2435.2.4.4.1240.1.5.1.9
OBJECT-TYPE    
  INTEGER 0..1  

brMultiIFPrimaryInterface 1.3.6.1.4.1.2435.2.4.4.1240.1.6
Primary Interface
OBJECT-TYPE    
  INTEGER  

brMultiIFInterfaceInformation 1.3.6.1.4.1.2435.2.4.4.1240.1.7
0bit Auto 1bit manual 2bit enable both 3bit disable both
OBJECT-TYPE    
  INTEGER  

brMultiIFcontrol 1.3.6.1.4.1.2435.2.4.4.1240.2
OBJECT IDENTIFIER    

brMultiIFControlTable 1.3.6.1.4.1.2435.2.4.4.1240.2.1
OBJECT-TYPE    
  SEQUENCE OF  
    BrMultiIFControlEntry

brMultiIFControlEntry 1.3.6.1.4.1.2435.2.4.4.1240.2.1.1
OBJECT-TYPE    
  BrMultiIFControlEntry  

brMultiIFSetDefault 1.3.6.1.4.1.2435.2.4.4.1240.2.1.1.1
Setting the value resets all parameters to their factory default value.
OBJECT-TYPE    
  INTEGER 0..32767  

brMultiIFservice 1.3.6.1.4.1.2435.2.4.4.1240.4
OBJECT IDENTIFIER    

brMultiIFServiceTable 1.3.6.1.4.1.2435.2.4.4.1240.4.1
OBJECT-TYPE    
  SEQUENCE OF  
    BrMultiIFServiceEntry

brMultiIFServiceEntry 1.3.6.1.4.1.2435.2.4.4.1240.4.1.1
OBJECT-TYPE    
  BrMultiIFServiceEntry  

brMultiIFServiceCount 1.3.6.1.4.1.2435.2.4.4.1240.4.1.1.1
Number of services on this print server.
OBJECT-TYPE    
  INTEGER 0..128  

brMultiIFServiceStringLimit 1.3.6.1.4.1.2435.2.4.4.1240.4.1.1.2
Maximum number of service strings supported by the print server.
OBJECT-TYPE    
  INTEGER 1..127  

brMultiIFServiceStringCount 1.3.6.1.4.1.2435.2.4.4.1240.4.1.1.3
Number of service strings currently defined on the print server.
OBJECT-TYPE    
  INTEGER  

brMultiIFServiceFilterCount 1.3.6.1.4.1.2435.2.4.4.1240.4.1.1.4
Number of service filters implemented by the device.
OBJECT-TYPE    
  INTEGER  

brMultiIFServiceInfoTable 1.3.6.1.4.1.2435.2.4.4.1240.4.2
This table represents the attributes of a service.
OBJECT-TYPE    
  SEQUENCE OF  
    BrMultiIFServiceInfoEntry

brMultiIFServiceInfoEntry 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1
A row in the services table. Rows cannot be created or deleted via direct SNMP operations.
OBJECT-TYPE    
  BrMultiIFServiceInfoEntry  

brMultiIFServiceIndex 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.1
The service number.
OBJECT-TYPE    
  INTEGER 1..32  

brMultiIFServiceName 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.2
The service name.
OBJECT-TYPE    
  DisplayString SIZE(1..32)  

brMultiIFServicePort 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.3
The port number assigned to this service.
OBJECT-TYPE    
  INTEGER 0..31  

brMultiIFServiceFilter 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.4
Filter number assigned to this service.
OBJECT-TYPE    
  INTEGER 0..255  

brMultiIFServiceBOT 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.5
Beginning of text string number assigned to this service.
OBJECT-TYPE    
  INTEGER 0..255  

brMultiIFServiceEOT 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.6
End of text string number assigned to this service.
OBJECT-TYPE    
  INTEGER 0..255  

brMultiIFServiceMatch 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.7
Match string number assigned to this service.
OBJECT-TYPE    
  INTEGER 0..255  

brMultiIFServiceReplace 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.8
Replace string number assigned to this service.
OBJECT-TYPE    
  INTEGER 0..255  

brMultiIFServiceTCPPort 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.9
TCP Port number assigned to this service.
OBJECT-TYPE    
  INTEGER 0..65535  

brMultiIFServiceNDSTree 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.10
The NDS Tree.
OBJECT-TYPE    
  DisplayString SIZE(1..48)  

brMultiIFServiceNDSContext 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.11
The NDS Context in Unicode.
OBJECT-TYPE    
  OCTET STRING SIZE(0..255)  

brMultiIFServiceVines 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.12
The Vines StreetTalk name for this service.
OBJECT-TYPE    
  DisplayString SIZE(1..48)  

brMultiIFServiceObsolete 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.13
Obsolete parameter that is no longer used
OBJECT-TYPE    
  INTEGER 0..127  

brMultiIFServiceNetwareServerCount 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.14
The number of Netware servers enabled on this service. Modifying the value will truncate the server list to the specified number of servers. If the value set is greater than the number of servers currently on the list, then the list will be unchanged.
OBJECT-TYPE    
  INTEGER 0..127  

brMultiIFServiceReceiveOnly 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.15
When enabled, the service will only receive data, any printer responses will be discarded.
OBJECT-TYPE    
  INTEGER 0..1  

brMultiIFServiceTCPQueued 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.16
When enabled, the raw TCP connections to the port will be queued while waiting for the port to become available
OBJECT-TYPE    
  INTEGER 0..1  

brMultiIFServiceProtocolLAT 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.17
When enabled, the LAT protocol will be available on this service.
OBJECT-TYPE    
  INTEGER 0..1  

brMultiIFServiceProtocolTCPIP 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.18
When enabled, the TCP/IP protocol will be available on this service.
OBJECT-TYPE    
  INTEGER 0..1  

brMultiIFServiceProtocolNetware 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.19
When enabled, the Netware protocol will be available on this service.
OBJECT-TYPE    
  INTEGER 0..1  

brMultiIFServiceProtocolAppleTalk 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.20
When enabled, the AppleTalk protocol will be available on this service.
OBJECT-TYPE    
  INTEGER 0..1  

brMultiIFServiceProtocolBanyan 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.21
When enabled, the Banyan protocol will be available on this service.
OBJECT-TYPE    
  INTEGER 0..1  

brMultiIFServiceProtocolDLC 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.22
When enabled, the DLC protocol will be available on this service.
OBJECT-TYPE    
  INTEGER 0..1  

brMultiIFServiceProtocolNetBEUI 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.23
When enabled, the NetBEUI protocol will be available on this service.
OBJECT-TYPE    
  INTEGER 0..1  

brMultiIFServiceNetwareServerMode 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.24
Netware mode for this service. 0 = Queue Server, 1 = Remote Printer
OBJECT-TYPE    
  INTEGER 0..1  

brMultiIFServiceNetwareRemotePrinterNum 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.25
Remote Printer Number for this service
OBJECT-TYPE    
  INTEGER 0..255  

brMultiIFServiceProtocolIPP 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.26
When enabled, the IPP protocol will be available on this service.
OBJECT-TYPE    
  INTEGER 0..1  

brMultiIFServiceAppleTalkType 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.27
AppleTalk type.
OBJECT-TYPE    
  DisplayString SIZE(1..32)  

brMultiIFServiceStringInfoTable 1.3.6.1.4.1.2435.2.4.4.1240.4.3
This table represents the service BOT/EOT/MATCH/REPLACE strings defined.
OBJECT-TYPE    
  SEQUENCE OF  
    BrMultiIFServiceStringInfoEntry

brMultiIFServiceStringInfoEntry 1.3.6.1.4.1.2435.2.4.4.1240.4.3.1
A row in the service string table. Rows cannot be created or deleted via direct SNMP operations.
OBJECT-TYPE    
  BrMultiIFServiceStringInfoEntry  

brMultiIFServiceStringIndex 1.3.6.1.4.1.2435.2.4.4.1240.4.3.1.1
The string number.
OBJECT-TYPE    
  INTEGER 1..255  

brMultiIFServiceString 1.3.6.1.4.1.2435.2.4.4.1240.4.3.1.2
The character string definition suitable for displaying.
OBJECT-TYPE    
  DisplayString SIZE(1..32)  

brMultiIFprotocol 1.3.6.1.4.1.2435.2.4.4.1240.5
OBJECT IDENTIFIER    

brMultiIFtcpip 1.3.6.1.4.1.2435.2.4.4.1240.5.2
OBJECT IDENTIFIER    

brMultiIFTCPIPTable 1.3.6.1.4.1.2435.2.4.4.1240.5.2.1
OBJECT-TYPE    
  SEQUENCE OF  
    BrMultiIFTCPIPEntry

brMultiIFTCPIPEntry 1.3.6.1.4.1.2435.2.4.4.1240.5.2.1.1
OBJECT-TYPE    
  BrMultiIFTCPIPEntry  

brMultiIFTCPIPAddress 1.3.6.1.4.1.2435.2.4.4.1240.5.2.1.1.1
IP Address assigned to the print server.
OBJECT-TYPE    
  IpAddress  

brMultiIFTCPIPSubnetMask 1.3.6.1.4.1.2435.2.4.4.1240.5.2.1.1.2
Subnet mask assigned to the print server.
OBJECT-TYPE    
  IpAddress  

brMultiIFTCPIPGateway 1.3.6.1.4.1.2435.2.4.4.1240.5.2.1.1.3
Gateway/Router address assigned to the print server
OBJECT-TYPE    
  IpAddress  

brMultiIFTCPIPMethod 1.3.6.1.4.1.2435.2.4.4.1240.5.2.1.1.4
Method used to determine the IP Address. AUTO tries all protocols. STATIC uses the configured address. DHCP, BOOTP, and RARP use only that protocol.
OBJECT-TYPE    
  INTEGER 0..7  

brMultiIFTCPIPUpdate 1.3.6.1.4.1.2435.2.4.4.1240.5.2.1.1.5
Hardware MAC address to be updated. This value is write only. Will read back as zeros.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

brMultiIFTCPIPTimeout 1.3.6.1.4.1.2435.2.4.4.1240.5.2.1.1.6
Timeout used for LPD connections.
OBJECT-TYPE    
  INTEGER 0..32767  

brMultiIFTCPIPBootTries 1.3.6.1.4.1.2435.2.4.4.1240.5.2.1.1.7
Number of attempts to use BOOTP, RARP, and DHCP.
OBJECT-TYPE    
  INTEGER 0..32767  

brMultiIFTCPIPRARPNoSubnet 1.3.6.1.4.1.2435.2.4.4.1240.5.2.1.1.8
If enabled, do not set the subnet mask based on the RARP response.
OBJECT-TYPE    
  INTEGER 0..1  

brMultiIFTCPIPRARPNoGateway 1.3.6.1.4.1.2435.2.4.4.1240.5.2.1.1.9
If enabled, do not set the gateway/router address based on the RARP response.
OBJECT-TYPE    
  INTEGER 0..1  

brMultiIFTCPIPUseMethod 1.3.6.1.4.1.2435.2.4.4.1240.5.2.1.1.10
Method type that used set up TCP/IP configuration.
OBJECT-TYPE    
  INTEGER 0..7  

brMultiIFTCPIPMethodServer 1.3.6.1.4.1.2435.2.4.4.1240.5.2.1.1.11
If TCP/IP configuration is setted up by any protocol server, this entry indicates the IP address of the server.
OBJECT-TYPE    
  IpAddress  

brMultiIFnetbeui 1.3.6.1.4.1.2435.2.4.4.1240.5.8
OBJECT IDENTIFIER    

brMultiIFNetBIOSTable 1.3.6.1.4.1.2435.2.4.4.1240.5.8.1
OBJECT-TYPE    
  SEQUENCE OF  
    BrMultiIFNetBIOSEntry

brMultiIFNetBIOSEntry 1.3.6.1.4.1.2435.2.4.4.1240.5.8.1.1
OBJECT-TYPE    
  BrMultiIFNetBIOSEntry  

brMultiIFNetBIOSIPMethod 1.3.6.1.4.1.2435.2.4.4.1240.5.8.1.1.1
Method used to determine the IP Address of the WINS server. AUTO tries all protocols (currently only DHCP is tried). STATIC uses the configured address.
OBJECT-TYPE    
  INTEGER 0..1  

brMultiIFTCPIPNetBIOSPrimaryWINSAddr 1.3.6.1.4.1.2435.2.4.4.1240.5.8.1.1.2
The IP Address of the primary WINS server.
OBJECT-TYPE    
  IpAddress  

brMultiIFTCPIPNetBIOSSecondaryWINSAddr 1.3.6.1.4.1.2435.2.4.4.1240.5.8.1.1.3
The IP Address of the secondary WINS server.
OBJECT-TYPE    
  IpAddress  

brMultiIFNetBEUIDomain 1.3.6.1.4.1.2435.2.4.4.1240.5.8.1.1.4
The NetBEUI domain name.
OBJECT-TYPE    
  DisplayString SIZE(0..15)  

brMultiIForiginalapipa 1.3.6.1.4.1.2435.2.4.4.1240.5.12
OBJECT IDENTIFIER    

brMultiIFAPIPATable 1.3.6.1.4.1.2435.2.4.4.1240.5.12.1
OBJECT-TYPE    
  SEQUENCE OF  
    BrMultiIFAPIPAEntry

brMultiIFAPIPAEntry 1.3.6.1.4.1.2435.2.4.4.1240.5.12.1.1
OBJECT-TYPE    
  BrMultiIFAPIPAEntry  

brMultiIFAPIPASupported 1.3.6.1.4.1.2435.2.4.4.1240.5.12.1.1.1
0 indicates the APIPA protocol is not supported. 1 indicates APIPA support is implemented by the firmware
OBJECT-TYPE    
  INTEGER 0..1  

brMultiIFAPIPAEnable 1.3.6.1.4.1.2435.2.4.4.1240.5.12.1.1.2
0 indicates the APIPA protocol is not enabled. 1 indicates that the APIPA protocol is enabled. Writing a non-zero value will enable the APIPA protocol if it is supported by the firmware.
OBJECT-TYPE    
  INTEGER 0..1  

brMultiIForiginalLAA 1.3.6.1.4.1.2435.2.4.4.1240.5.14
OBJECT IDENTIFIER    

brMultiIFLAATable 1.3.6.1.4.1.2435.2.4.4.1240.5.14.1
OBJECT-TYPE    
  SEQUENCE OF  
    BrMultiIFLAAEntry

brMultiIFLAAEntry 1.3.6.1.4.1.2435.2.4.4.1240.5.14.1.1
OBJECT-TYPE    
  BrMultiIFLAAEntry  

brMultiIFLAASupported 1.3.6.1.4.1.2435.2.4.4.1240.5.14.1.1.1
This value indicate if the locally administered addressing is supported. 0: Not Supported 1: Supported
OBJECT-TYPE    
  INTEGER 0..1  

brMultiIFLAAMacAddress 1.3.6.1.4.1.2435.2.4.4.1240.5.14.1.1.2
A locally administered address (LAA) that replaces the factory-assigned MAC address (UAA: universally administered address). If this setting is all-zero address (i.e. 6 bytes of zeros), the factory-assigned MAC address is used as the MAC address of the device. The LAA address must start with X2, X6, XA, or XE, where X is any hexadecimal digit 0 to F.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

brMultiIForiginalIPv6 1.3.6.1.4.1.2435.2.4.4.1240.5.15
OBJECT IDENTIFIER    

brMultiIFIPv6AddressCountTable 1.3.6.1.4.1.2435.2.4.4.1240.5.15.1
OBJECT-TYPE    
  SEQUENCE OF  
    BrMultiIFIPv6AddressCountEntry

brMultiIFIPv6AddressCountEntry 1.3.6.1.4.1.2435.2.4.4.1240.5.15.1.1
OBJECT-TYPE    
  BrMultiIFIPv6AddressCountEntry  

brMultiIFIPv6AddressCount 1.3.6.1.4.1.2435.2.4.4.1240.5.15.1.1.1
IPv6Address Counter.
OBJECT-TYPE    
  INTEGER  

brMultiIFIPv6AddressTable 1.3.6.1.4.1.2435.2.4.4.1240.5.15.2
OBJECT-TYPE    
  SEQUENCE OF  
    BrMultiIFIPv6AddressEntry

brMultiIFIPv6AddressEntry 1.3.6.1.4.1.2435.2.4.4.1240.5.15.2.1
OBJECT-TYPE    
  BrMultiIFIPv6AddressEntry  

brMultiIFIPv6AddressIndex 1.3.6.1.4.1.2435.2.4.4.1240.5.15.2.1.1
index
OBJECT-TYPE    
  INTEGER 1..16  

brMultiIFIPv6Address 1.3.6.1.4.1.2435.2.4.4.1240.5.15.2.1.2
OBJECT-TYPE    
  Ipv6Address  

brMultiIFIPv6UseMethod 1.3.6.1.4.1.2435.2.4.4.1240.5.15.2.1.3
Method type that used set up TCP/IP configuration. 0: Unknown (Information not supported) 1: Manually 2: DHCPv6 3: Stateless Address Auto-configuration 4: Reserved 5: Link Local
OBJECT-TYPE    
  INTEGER 0..7  

brMultiIFIPv6MethodServer 1.3.6.1.4.1.2435.2.4.4.1240.5.15.2.1.4
If TCP/IP configuration is setted up by any protocol server, this entry indicates the IP address of the server.
OBJECT-TYPE    
  DisplayString SIZE(0..64)  

brMultiIFIPv6StaticAddressCountTable 1.3.6.1.4.1.2435.2.4.4.1240.5.15.3
OBJECT-TYPE    
  SEQUENCE OF  
    BrMultiIFIPv6StaticAddressCountEntry

brMultiIFIPv6StaticAddressCountEntry 1.3.6.1.4.1.2435.2.4.4.1240.5.15.3.1
OBJECT-TYPE    
  BrMultiIFIPv6StaticAddressCountEntry  

brMultiIFIPv6StaticAddressCount 1.3.6.1.4.1.2435.2.4.4.1240.5.15.3.1.1
IPv6StaticAddress Counter.
OBJECT-TYPE    
  INTEGER  

brMultiIFIPv6StaticAddressTable 1.3.6.1.4.1.2435.2.4.4.1240.5.15.4
OBJECT-TYPE    
  SEQUENCE OF  
    BrMultiIFIPv6StaticAddressEntry

brMultiIFIPv6StaticAddressEntry 1.3.6.1.4.1.2435.2.4.4.1240.5.15.4.1
OBJECT-TYPE    
  BrMultiIFIPv6StaticAddressEntry  

brMultiIFIPv6StaticAddressIndex 1.3.6.1.4.1.2435.2.4.4.1240.5.15.4.1.1
index
OBJECT-TYPE    
  INTEGER 1..16  

brMultiIFIPv6StaticAddressEnable 1.3.6.1.4.1.2435.2.4.4.1240.5.15.4.1.2
index
OBJECT-TYPE    
  INTEGER  

brMultiIFIPv6StaticAddress 1.3.6.1.4.1.2435.2.4.4.1240.5.15.4.1.3
IPv6 Static Address
OBJECT-TYPE    
  Ipv6Address  

brMultiIFIPv6StaticAddressPrefixLength 1.3.6.1.4.1.2435.2.4.4.1240.5.15.4.1.4
IPv6Address Prefix Length
OBJECT-TYPE    
  INTEGER  

brMultiIFDNSIPv6AddressTable 1.3.6.1.4.1.2435.2.4.4.1240.5.15.5
OBJECT-TYPE    
  SEQUENCE OF  
    BrMultiIFDNSIPv6AddressEntry

brMultiIFDNSIPv6AddressEntry 1.3.6.1.4.1.2435.2.4.4.1240.5.15.5.1
OBJECT-TYPE    
  BrMultiIFDNSIPv6AddressEntry  

brMultiIFPrimaryDNSIPv6Address 1.3.6.1.4.1.2435.2.4.4.1240.5.15.5.1.1
Primary DNS IPv6 Address
OBJECT-TYPE    
  Ipv6Address  

brMultiIFSecondaryDNSIPv6Address 1.3.6.1.4.1.2435.2.4.4.1240.5.15.5.1.2
Secondary DNS IPv6 Address
OBJECT-TYPE    
  Ipv6Address  

brMultiIForiginalWebServices 1.3.6.1.4.1.2435.2.4.4.1240.5.16
OBJECT IDENTIFIER    

brMultiIFWebServicesTable 1.3.6.1.4.1.2435.2.4.4.1240.5.16.1
OBJECT-TYPE    
  SEQUENCE OF  
    BrMultiIFWebServicesEntry

brMultiIFWebServicesEntry 1.3.6.1.4.1.2435.2.4.4.1240.5.16.1.1
OBJECT-TYPE    
  BrMultiIFWebServicesEntry  

brMultiIFWebServicesName 1.3.6.1.4.1.2435.2.4.4.1240.5.16.1.1.1
OBJECT-TYPE    
  DisplayString SIZE(0..64)  

brMultiIFWebServicesInstanceID 1.3.6.1.4.1.2435.2.4.4.1240.5.16.1.1.2
OBJECT-TYPE    
  INTEGER 1..2147483647  

brMultiIFWebServicesMetadataVersion 1.3.6.1.4.1.2435.2.4.4.1240.5.16.1.1.3
OBJECT-TYPE    
  INTEGER 1..2147483647  

Defined Objects

BrOneTouchDialEntry  
SEQUENCE    
  INTEGER as brOneTouchDialIndex  
  OCTET STRING as brOneTouchDialData  

BrSpeedDialEntry  
SEQUENCE    
  INTEGER as brSpeedDialIndex  
  OCTET STRING as brSpeedDialData  

BrTrayPriorityEntry  
SEQUENCE    
  INTEGER as brTrayPriorityIndex  
  OCTET STRING as brTrayPriorityMember  

BrCarbonCopyEntry  
SEQUENCE    
  INTEGER as brCarbonCopyIndex  
  INTEGER as brCarbonCopyTray  
  INTEGER as brCarbonCopyMacro  
  INTEGER as brCarbonCopyMacroID  

BrPrtMailboxProtectEntry  
SEQUENCE    
  INTEGER as brPrtMailboxProtectIndex  
  INTEGER as brPrtMailboxProtect  

BrPrtAvoidMailboxFullEntry  
SEQUENCE    
  INTEGER as brPrtAvoidMailboxFullIndex  
  INTEGER as brPrtAvoidMailboxFull  

BrErrorHistoryEntry  
SEQUENCE    
  INTEGER as brErrorHistoryIndex  
  OCTET STRING as brErrorHistoryDescription  

BrCommunicationErrorHistoryEntry  
SEQUENCE    
  INTEGER as brCommunicationErrorHistoryIndex  
  OCTET STRING as brCommunicationErrorHistoryDescription  

BrPrintPagesEntry  
SEQUENCE    
  INTEGER as brPrintPagesIndex  
  INTEGER as brPrintPagesPaperSize  
  Counter as brPrintPages  

BrPrintPagesMediaPlaceEntry  
SEQUENCE    
  INTEGER as brPrintPagesMediaPlaceIndex  
  INTEGER as brPrintPagesMediaPlaceType  
  Counter as brPrintPagesMediaPlaceCounter  

BrPrintPagesFuncEntry  
SEQUENCE    
  INTEGER as brPrintPagesFuncIndex  
  INTEGER as brPrintPagesFuncType  
  Counter as brPrintPagesFuncCounter  

BrPrintPagesPaperTypeEntry  
SEQUENCE    
  INTEGER as brPrintPagesPaperTypeIndex  
  INTEGER as brPrintPagesPaperTypeType  
  Counter as brPrintPagesPaperTypeCounter  

BrCapabilityOrientationEntry  
SEQUENCE    
  INTEGER as brCapabilityOrientationIndex  
  DisplayString as brCapabilityOrientationName  

BrCapabilityPaperEntry  
SEQUENCE    
  INTEGER as brCapabilityPaperIndex  
  DisplayString as brCapabilityPaperName  

BrCapabilityMediatypeEntry  
SEQUENCE    
  INTEGER as brCapabilityMediatypeIndex  
  DisplayString as brCapabilityMediatypeName  

BrCapabilityResolutionEntry  
SEQUENCE    
  INTEGER as brCapabilityResolutionIndex  
  INTEGER as brCapabilityResolution  

BrPfKitEntry  
SEQUENCE    
  INTEGER as brPfKitIndex  
  INTEGER as brPfKitType  
  Counter as brPfKitCount  

BrScanCountEntry  
SEQUENCE    
  INTEGER as brScanCountIndex  
  INTEGER as brScanCountType  
  Counter as brScanCountCounter  

BrNotificationEntry  
SEQUENCE    
  INTEGER as brNotificationIndex  
  OCTET STRING as brNotificationAddress  
  INTEGER as brNotificationStatusGroup  
  INTEGER as brNotificationShowURLInfo  
  OCTET STRING as brNotificationErrorRule  
  INTEGER as brNotificationRestoration  

BrNotificationRuleEntry  
SEQUENCE    
  INTEGER as brNotificationRuleIndex  
  INTEGER as brNotificationStatusID  
  INTEGER as brNotificationMainRule  
  INTEGER as brNotificationRuleValue  

BrPJLInfoOptionsEntry  
SEQUENCE    
  INTEGER as brPJLInfoOptionsIndex  
  OCTET STRING as brPJLInfoOptions  

BrPJLInfoIntrayconfigEntry  
SEQUENCE    
  INTEGER as brPJLInfoIntrayconfigIndex  
  OCTET STRING as brPJLInfoIntrayconfig  

BrPJLInfoOuttrayconfigEntry  
SEQUENCE    
  INTEGER as brPJLInfoOuttrayconfigIndex  
  OCTET STRING as brPJLInfoOuttrayconfig  

BrPJLInfoDXconfigEntry  
SEQUENCE    
  INTEGER as brPJLInfoDXconfigIndex  
  OCTET STRING as brPJLInfoDXconfig  

BrPJLInfoStorageconfigEntry  
SEQUENCE    
  INTEGER as brPJLInfoStorageconfigIndex  
  OCTET STRING as brPJLInfoStorageconfig  

BrEmailReportsEntry  
SEQUENCE    
  INTEGER as brEmailReportsIndex  
  OCTET STRING as brEmailReportsAddress  
  INTEGER as brEmailReportsFrequency  
  OCTET STRING as brEmailReportsTime  
  INTEGER as brEmailReportsWeek  
  INTEGER as brEmailReportsDate  
  INTEGER as brEmailReportsSendReportNow  
  INTEGER as brEmailReportsSendReportatPowerOn  
  INTEGER as brEmailReportsNoRTCFrequency  
  INTEGER as brEmailReportsReportFormat  

BrpsPortInfoEntry  
SEQUENCE    
  INTEGER as brpsPortIndex  
  DisplayString as brpsPortName  
  INTEGER as brpsPortType  
  INTEGER as brpsPortStatus  
  DisplayString as brpsPortStatusString  
  INTEGER as brpsPortProtocol  
  INTEGER as brpsPortQueueSize  
  DisplayString as brpsPortDescriptionString  
  DisplayString as brpsPortInfoString  
  INTEGER as brpsPortHTTPExtensions  
  INTEGER as brpsPortSNMPExtensions  
  DisplayString as brpsPortAttribute  
  INTEGER as brpsPortBinaryMode  
  INTEGER as brpsPortInhibitDatagramSupport  

BrpsServiceInfoEntry  
SEQUENCE    
  INTEGER as brpsServiceIndex  
  DisplayString as brpsServiceName  
  INTEGER as brpsServicePort  
  INTEGER as brpsServiceFilter  
  INTEGER as brpsServiceBOT  
  INTEGER as brpsServiceEOT  
  INTEGER as brpsServiceMatch  
  INTEGER as brpsServiceReplace  
  INTEGER as brpsServiceTCPPort  
  DisplayString as brpsServiceNDSTree  
  OCTET STRING as brpsServiceNDSContext  
  DisplayString as brpsServiceVines  
  INTEGER as brpsServiceObsolete  
  INTEGER as brpsServiceNetwareServerCount  
  INTEGER as brpsServiceReceiveOnly  
  INTEGER as brpsServiceTCPQueued  
  INTEGER as brpsServiceProtocolLAT  
  INTEGER as brpsServiceProtocolTCPIP  
  INTEGER as brpsServiceProtocolNetware  
  INTEGER as brpsServiceProtocolAppleTalk  
  INTEGER as brpsServiceProtocolBanyan  
  INTEGER as brpsServiceProtocolDLC  
  INTEGER as brpsServiceProtocolNetBEUI  
  INTEGER as brpsServiceNetwareServerMode  
  INTEGER as brpsServiceNetwareRemotePrinterNum  
  INTEGER as brpsServiceProtocolIPP  
  DisplayString as brpsServiceAppleTalkType  

BrpsServiceStringInfoEntry  
SEQUENCE    
  INTEGER as brpsServiceStringIndex  
  DisplayString as brpsServiceString  

BrpsTCPIPAccessEntry  
SEQUENCE    
  INTEGER as brpsTCPIPAccessIndex  
  IpAddress as brpsTCPIPAccessNodeAddress  
  IpAddress as brpsTCPIPAccessSubnetMask  

BrpsNetwareServerEntry  
SEQUENCE    
  INTEGER as brpsNetwareServerIndex  
  DisplayString as brpsNetwareServerName  

BrProxyServerInfoEntry  
SEQUENCE    
  INTEGER as brProxyServerInfoIndex  
  INTEGER as brProxyServerType  
  OCTET STRING as brProxyServerName  
  INTEGER as brProxyServerPort  

BrSNMPTrapEntry  
SEQUENCE    
  INTEGER as brSNMPTrapIndex  
  IpAddress as brTCPIPServerAddress  

BrpsWLanCapabilityEncryptModeEntry  
SEQUENCE    
  INTEGER as brpsWLanCapabilityEncryptModeIndex  
  INTEGER as brpsWLanCapabilityEncryptModeType  
  OCTET STRING as brpsWLanCapabilityEncryptModeDescription  
  INTEGER as brpsWLanCapabilityEncryptModeSupported  

BrpsWLanCapabilityAuthModeEntry  
SEQUENCE    
  INTEGER as brpsWLanCapabilitAuthModeIndex  
  INTEGER as brpsWLanCapabilityAuthModeType  
  OCTET STRING as brpsWLanCapabilityAuthModeDescription  
  INTEGER as brpsWLanCapabilityAuthModeSupported  

BrpsWLanCapabilityAuthEAPEntry  
SEQUENCE    
  INTEGER as brpsWLanCapabilityAuthEAPIndex  
  INTEGER as brpsWLanCapabilityAuthEAPType  
  OCTET STRING as brpsWLanCapabilityAuthEAPDescription  
  INTEGER as brpsWLanCapabilityAuthEAPSupported  
  INTEGER as brpsWLanCapabilityAuthEAPSupportAuthentication  
  INTEGER as brpsWLanCapabilityAuthEAPSupportEncryption  

BrpsAvailableWLanEntry  
SEQUENCE    
  INTEGER as brpsAvailableWLanIndex  
  OCTET STRING as brpsAvailableWLanName  
  INTEGER as brpsAvailableWLanMode  
  INTEGER as brpsAvailableWLanCommMode  
  INTEGER as brpsAvailableWLanChannel  
  INTEGER as brpsAvailableWLanPowerLevel  
  INTEGER as brpsAvailableWLanAuthMode  
  INTEGER as brpsAvailableWLanEncryptMode  

BrpsWLanWepKeyEntry  
SEQUENCE    
  INTEGER as brpsWLanWepKeyIndex  
  INTEGER as brpsWLanWepKeySize  
  INTEGER as brpsWLanWepKeyType  
  OCTET STRING as brpsWLanWepKey  

BrMultiIFConfigureEntry  
SEQUENCE    
  INTEGER as brMultiIFConfigureIndex  
  INTEGER as brMultiIFType  
  DisplayString as brMultiIFDescription  
  OCTET STRING as brMultiIFNodeName  
  INTEGER as brMultiIFInterfaceEnable  
  INTEGER as brMultiIFEnetMode  
  INTEGER as brMultiIFHardwareType  
  OCTET STRING as brMultiIFNodeType  
  INTEGER as brMultiIFInterfaceEnableImmediate  

BrMultiIFDNSEntry  
SEQUENCE    
  INTEGER as brMultiIFTCPIPDNSIPSetup  
  IpAddress as brMultiIFPrimaryDNSIPAddress  
  IpAddress as brMultiIFSecondaryDNSIPAddress  
  INTEGER as brMultiIFTCPIPConnectTime  

BrMultiIFControlEntry  
SEQUENCE    
  INTEGER as brMultiIFSetDefault  

BrMultiIFServiceEntry  
SEQUENCE    
  INTEGER as brMultiIFServiceCount  
  INTEGER as brMultiIFServiceStringLimit  
  INTEGER as brMultiIFServiceStringCount  
  INTEGER as brMultiIFServiceFilterCount  

BrMultiIFServiceInfoEntry  
SEQUENCE    
  INTEGER as brMultiIFServiceIndex  
  DisplayString as brMultiIFServiceName  
  INTEGER as brMultiIFServicePort  
  INTEGER as brMultiIFServiceFilter  
  INTEGER as brMultiIFServiceBOT  
  INTEGER as brMultiIFServiceEOT  
  INTEGER as brMultiIFServiceMatch  
  INTEGER as brMultiIFServiceReplace  
  INTEGER as brMultiIFServiceTCPPort  
  DisplayString as brMultiIFServiceNDSTree  
  OCTET STRING as brMultiIFServiceNDSContext  
  DisplayString as brMultiIFServiceVines  
  INTEGER as brMultiIFServiceObsolete  
  INTEGER as brMultiIFServiceNetwareServerCount  
  INTEGER as brMultiIFServiceReceiveOnly  
  INTEGER as brMultiIFServiceTCPQueued  
  INTEGER as brMultiIFServiceProtocolLAT  
  INTEGER as brMultiIFServiceProtocolTCPIP  
  INTEGER as brMultiIFServiceProtocolNetware  
  INTEGER as brMultiIFServiceProtocolAppleTalk  
  INTEGER as brMultiIFServiceProtocolBanyan  
  INTEGER as brMultiIFServiceProtocolDLC  
  INTEGER as brMultiIFServiceProtocolNetBEUI  
  INTEGER as brMultiIFServiceNetwareServerMode  
  INTEGER as brMultiIFServiceNetwareRemotePrinterNum  
  INTEGER as brMultiIFServiceProtocolIPP  
  DisplayString as brMultiIFServiceAppleTalkType  

BrMultiIFServiceStringInfoEntry  
SEQUENCE    
  INTEGER as brMultiIFServiceStringIndex  
  DisplayString as brMultiIFServiceString  

BrMultiIFTCPIPEntry  
SEQUENCE    
  IpAddress as brMultiIFTCPIPAddress  
  IpAddress as brMultiIFTCPIPSubnetMask  
  IpAddress as brMultiIFTCPIPGateway  
  INTEGER as brMultiIFTCPIPMethod  
  OCTET STRING as brMultiIFTCPIPUpdate  
  INTEGER as brMultiIFTCPIPTimeout  
  INTEGER as brMultiIFTCPIPBootTries  
  INTEGER as brMultiIFTCPIPRARPNoSubnet  
  INTEGER as brMultiIFTCPIPRARPNoGateway  
  INTEGER as brMultiIFTCPIPUseMethod  
  IpAddress as brMultiIFTCPIPMethodServer  

BrMultiIFNetBIOSEntry  
SEQUENCE    
  INTEGER as brMultiIFNetBIOSIPMethod  
  IpAddress as brMultiIFTCPIPNetBIOSPrimaryWINSAddr  
  IpAddress as brMultiIFTCPIPNetBIOSSecondaryWINSAddr  
  DisplayString as brMultiIFNetBEUIDomain  

BrMultiIFAPIPAEntry  
SEQUENCE    
  INTEGER as brMultiIFAPIPASupported  
  INTEGER as brMultiIFAPIPAEnable  

BrMultiIFLAAEntry  
SEQUENCE    
  INTEGER as brMultiIFLAASupported  
  OCTET STRING as brMultiIFLAAMacAddress  

BrMultiIFIPv6AddressCountEntry  
SEQUENCE    
  INTEGER as brMultiIFIPv6AddressCount  

BrMultiIFIPv6AddressEntry  
SEQUENCE    
  INTEGER as brMultiIFIPv6AddressIndex  
  Ipv6Address as brMultiIFIPv6Address  
  INTEGER as brMultiIFIPv6UseMethod  
  DisplayString as brMultiIFIPv6MethodServer  

BrMultiIFIPv6StaticAddressCountEntry  
SEQUENCE    
  INTEGER as brMultiIFIPv6StaticAddressCount  

BrMultiIFIPv6StaticAddressEntry  
SEQUENCE    
  INTEGER as brMultiIFIPv6StaticAddressIndex  
  INTEGER as brMultiIFIPv6StaticAddressEnable  
  Ipv6Address as brMultiIFIPv6StaticAddress  
  INTEGER as brMultiIFIPv6StaticAddressPrefixLength  

BrMultiIFDNSIPv6AddressEntry  
SEQUENCE    
  Ipv6Address as brMultiIFPrimaryDNSIPv6Address  
  Ipv6Address as brMultiIFSecondaryDNSIPv6Address  

BrMultiIFWebServicesEntry  
SEQUENCE    
  DisplayString as brMultiIFWebServicesName  
  INTEGER as brMultiIFWebServicesInstanceID  
  INTEGER as brMultiIFWebServicesMetadataVersion  

BrLdapServerInfoEntry  
SEQUENCE    
  INTEGER as brLdapServerInfoIndex  
  DisplayString as brLdapServerName  
  INTEGER as brLdapServerPort  
  INTEGER as brLdapServerAuth  
  OCTET STRING as brLdapServerUserDN  
  OCTET STRING as brLdapServerPassword  
  INTEGER as brLdapServerPasswordSet  
  OCTET STRING as brLdapServerBaseDN  
  DisplayString as brLdapServerAttrEMail  
  DisplayString as brLdapServerAttrFAXNumber  
  DisplayString as brLdapServerAttrDetail1  
  DisplayString as brLdapServerAttrDetail2  
  DisplayString as brLdapServerAttrDetail3  
  DisplayString as brLdapServerAttrDetail4  
  INTEGER as brLdapServerAttrDetailEnable1  
  INTEGER as brLdapServerAttrDetailEnable2  
  INTEGER as brLdapServerAttrDetailEnable3  
  INTEGER as brLdapServerAttrDetailEnable4  
  DisplayString as brLdapKerberosServerName  
  INTEGER as brLdapKerberosServerPort  

BrLdapServerAttrNameEntry  
SEQUENCE    
  INTEGER as brLdapServerAttrNameIndex  
  DisplayString as brLdapServerAttrName  

BrFuncLockPublicEntry  
SEQUENCE    
  INTEGER as brFuncLockPublicFuncIndex  
  INTEGER as brFuncLockPublicFuncMember  
  INTEGER as brFuncLockPublicFuncSupported  
  INTEGER as brFuncLockPublicFuncEnable  

BrFuncLockUserEntry  
SEQUENCE    
  INTEGER as brFuncLockUserIndex  
  DisplayString as brFuncLockUserName  
  DisplayString as brFuncLockUserPassword  

BrFuncLockUserFuncEntry  
SEQUENCE    
  INTEGER as brFuncLockUserFuncIndex  
  INTEGER as brFuncLockUserFuncMember  
  INTEGER as brFuncLockUserFuncSupported  
  INTEGER as brFuncLockUserFuncEnable  

BrPJLInfoFirmwareUpdateconfigEntry  
SEQUENCE    
  INTEGER as brPJLInfoFirmwareUpdateconfigIndex  
  OCTET STRING as brPJLInfoFirmwareUpdateconfig  

BrFirmwareUpdateKeywordEntry  
SEQUENCE    
  INTEGER as brFirmwareUpdateKeywordIndex  
  OCTET STRING as brFirmwareUpdateKeyword  

BrFuncLockUserPrintPageEntry  
SEQUENCE    
  INTEGER as brFuncLockUserPrintPageCountMono  
  INTEGER as brFuncLockUserPrintPageCountColor  
  INTEGER as brFuncLockUserPrintPageIndex  
  INTEGER as brFuncLockUserPrintPageLimitEnable  
  INTEGER as brFuncLockUserPrintPageMax  
  INTEGER as brFuncLockUserPrintPageCountMonoLast  
  INTEGER as brFuncLockUserPrintPageCountColorLast  

BrFuncLockPcLoginNameEntry  
SEQUENCE    
  INTEGER as brFuncLockPcLoginNameAuthIndex  
  OCTET STRING as brFuncLockPcLoginName  
  INTEGER as brFuncLockPcLoginNameAuthID