BayNetworks-IISIS-MIB

File: BayNetworks-IISIS-MIB.mib (43604 bytes)

Imported modules

RFC1155-SMI RFC-1212 RFC1213-MIB
Wellfleet-COMMON-MIB

Imported symbols

Counter IpAddress Gauge
OBJECT-TYPE DisplayString wfIisisGroup

Defined Objects

wfIisisGeneralGroup 1.3.6.1.4.1.18.3.5.3.2.8.1
OBJECT IDENTIFIER    

wfIisisGeneralDelete 1.3.6.1.4.1.18.3.5.3.2.8.1.1
'This value determines whether I-ISIS is configured'
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfIisisGeneralDisable 1.3.6.1.4.1.18.3.5.3.2.8.1.2
'The administrative status of I-ISIS in the router. The value 'enabled' denotes that the I-ISIS Process is active on at least one interface; 'disabled' disables it on all interfaces.'
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfIisisGeneralState 1.3.6.1.4.1.18.3.5.3.2.8.1.3
'The state of I-ISIS'
OBJECT-TYPE    
  INTEGER up(1), down(2), invalid(3), notpresent(4)  

wfIisisRouterId 1.3.6.1.4.1.18.3.5.3.2.8.1.4
This value contains the system ID of this Intermediate System.
OBJECT-TYPE    
  OCTET STRING  

wfIisisVersion 1.3.6.1.4.1.18.3.5.3.2.8.1.5
This read-only parameter identifies the version number of the IS-IS protocol to which this node conforms to.
OBJECT-TYPE    
  DisplayString  

wfIisisRouterType 1.3.6.1.4.1.18.3.5.3.2.8.1.6
This value determines whether this system is L1 only router L2 only router or L1-L2 IS.
OBJECT-TYPE    
  INTEGER l1only(1), l2only(2), l1l2(3)  

wfIisisSpfHoldDown 1.3.6.1.4.1.18.3.5.3.2.8.1.7
Hold Down Timer for the SPF (in seconds). The SPF will run at most once per hold down timer value. A value of 0 means no hold down.
OBJECT-TYPE    
  INTEGER 0..60  

wfIisisPrimaryLogMask 1.3.6.1.4.1.18.3.5.3.2.8.1.8
A parameter to specify which I-ISIS log messages should be logged. This will only effect the Primary I-ISIS gate. Each bit represents a message as defined below. A 1 in that bit location means to log it and a 0 means not to put that log message in the log. Changing this value will NOT restart I-ISIS, but will take effct immediately(if there are any messages to be logged. bit 31 bit 0 +---------------------------------------+ | | +---------------------------------------+ bit0 Trace Messages bit1 INFO Level messages bit2 debug level messages bit3 I-ISIS interface state change messages bit4 Nbr state changes bit5 self-origination of LSA's bit6 receipt of new LSA's bit7 changes to I-ISIS`s Routing Table bit8 Bad LS requests, Ack's, or updates bit9 receipt of less recent LSA's bit10 receipt of more recent self-originated LSA's bit11 receipt of MAxAge LSA's (i.e. LSA's being flushed) bit12 - 31 reserved
OBJECT-TYPE    
  Gauge  

wfIisisMaximumPath 1.3.6.1.4.1.18.3.5.3.2.8.1.9
Maximum number of equal cost paths allowed for a network installed by OSPF.
OBJECT-TYPE    
  INTEGER 1..12  

wfIisisMaxAreas 1.3.6.1.4.1.18.3.5.3.2.8.1.10
This value defines the maximum allowable number of areas addresses for the domain that this router exists in.
OBJECT-TYPE    
  INTEGER 1..3  

wfIisisNumL1Lsps 1.3.6.1.4.1.18.3.5.3.2.8.1.11
Number of L2 LSPS stored in the database
OBJECT-TYPE    
  Gauge  

wfIisisNumL2Lsps 1.3.6.1.4.1.18.3.5.3.2.8.1.12
Number of L2 LSPS stored in the database
OBJECT-TYPE    
  Gauge  

wfIisisCksumIsPdus 1.3.6.1.4.1.18.3.5.3.2.8.1.13
This value indicates whether ISIS PDUs will carry a checksum.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfIisisL1LspPassword 1.3.6.1.4.1.18.3.5.3.2.8.1.14
This assigns a password such that only L1 Lsps with the matching password will be accepted. All L1 Lsps generated by this system will contain this string in the password option.
OBJECT-TYPE    
  DisplayString  

wfIisisL2LspPassword 1.3.6.1.4.1.18.3.5.3.2.8.1.15
This assigns a password such that only L2 Lsps with the matching password will be accepted. All L2 Lsps generated by this system will contain this string in the password option.
OBJECT-TYPE    
  DisplayString  

wfIisisAreaAddr 1.3.6.1.4.1.18.3.5.3.2.8.1.16
This Assigns the area address for this router. This field must be filled in. If the user doesn't enter a value, then assign 0x470005. Site Manager must force the user to enter at least a 3-byte value for this field.
OBJECT-TYPE    
  OCTET STRING  

wfIisisAreaAddrAlias1 1.3.6.1.4.1.18.3.5.3.2.8.1.17
This Assigns the first area address alias for this router. This field does no have to be filled in, but if the user tries to enter a value, Site Manager must make sure that it is at least 3-bytes in length.
OBJECT-TYPE    
  OCTET STRING  

wfIisisAreaAddrAlias2 1.3.6.1.4.1.18.3.5.3.2.8.1.18
This Assigns the second area address alias for this router. This field does no have to be filled in, but if the user tries to enter a value, Site Manager must make sure that it is at least 3-bytes in length.
OBJECT-TYPE    
  OCTET STRING  

wfIisisL1CorruptedLsps 1.3.6.1.4.1.18.3.5.3.2.8.1.19
Number of Corrupted L1-Lsps Detected.
OBJECT-TYPE    
  Counter  

wfIisisL2CorruptedLsps 1.3.6.1.4.1.18.3.5.3.2.8.1.20
Number of Corrupted L2-Lsps Detected.
OBJECT-TYPE    
  Counter  

wfIisisL1LspDbOverLoads 1.3.6.1.4.1.18.3.5.3.2.8.1.21
Number of times the L1 Lsp Database Overload event has been generated.
OBJECT-TYPE    
  Counter  

wfIisisL2LspDbOverLoads 1.3.6.1.4.1.18.3.5.3.2.8.1.22
Number of times the L2Lsp Database Overload event has been generated.
OBJECT-TYPE    
  Counter  

wfIisisNearestL2Is 1.3.6.1.4.1.18.3.5.3.2.8.1.23
This is the ID of the nearest L2 system in this area.
OBJECT-TYPE    
  OCTET STRING  

wfIisisNumL1Routes 1.3.6.1.4.1.18.3.5.3.2.8.1.24
Number of L1 Routes.
OBJECT-TYPE    
  Gauge  

wfIisisNumL2Routes 1.3.6.1.4.1.18.3.5.3.2.8.1.25
Number of L2 Routes.
OBJECT-TYPE    
  Gauge  

wfIisisMinLSPGenerationInterval 1.3.6.1.4.1.18.3.5.3.2.8.1.26
Min time interval(in secs) before LSP generation
OBJECT-TYPE    
  INTEGER 5..900  

wfIisisMaxLSPGenerationInterval 1.3.6.1.4.1.18.3.5.3.2.8.1.27
Max time interval(in secs) before LSP generation
OBJECT-TYPE    
  INTEGER 150..27000  

wfIisisMaxAge 1.3.6.1.4.1.18.3.5.3.2.8.1.28
The lifetime of the lsp after which it will be considered expired
OBJECT-TYPE    
  INTEGER 300..7200  

wfIisisMinLSPXmtInterval 1.3.6.1.4.1.18.3.5.3.2.8.1.29
OBJECT-TYPE    
  INTEGER 0..100  

wfIisisPartialSNPInterval 1.3.6.1.4.1.18.3.5.3.2.8.1.30
OBJECT-TYPE    
  INTEGER 1..30  

wfIisisZeroAgeLifetime 1.3.6.1.4.1.18.3.5.3.2.8.1.31
If the remaining lifetime of an LSP reaches zero, the expired LSP will be kept in the database for this time (in seconds)
OBJECT-TYPE    
  INTEGER 0..120  

wfIisisAgePend 1.3.6.1.4.1.18.3.5.3.2.8.1.32
The number of entries processed before this gate pends
OBJECT-TYPE    
  INTEGER 10..100  

wfIisisCsnpBuildInterval 1.3.6.1.4.1.18.3.5.3.2.8.1.33
The interval at which CSNPs are generated by the Designated IS
OBJECT-TYPE    
  INTEGER 10..1200  

wfIisisL2LspBufferSize 1.3.6.1.4.1.18.3.5.3.2.8.1.34
The max size of the LSP generated by system
OBJECT-TYPE    
  INTEGER 256..16384  

wfIisisL1SpfCnt 1.3.6.1.4.1.18.3.5.3.2.8.1.35
The number of times the L1 I-ISIS SPF algorithm has been run for this area.
OBJECT-TYPE    
  Counter  

wfIisisL2SpfCnt 1.3.6.1.4.1.18.3.5.3.2.8.1.36
The number of times the L2 I-ISIS SPF algorithm has been run for this area.
OBJECT-TYPE    
  Counter  

wfIisisAreaTable 1.3.6.1.4.1.18.3.5.3.2.8.2
-- The I-ISIS Area Data Structure contains information -- regarding the various areas. The interfaces and -- links are configured as part of these areas. -- Area 0.0.0.0, by definition, is the Backbone Area 'Information describing the configured parameters and cumulative statistics of the router's attached areas.' REFERENCE 'I-ISIS Version 2, Section 6 The Area Data Structure'
OBJECT-TYPE    
  SEQUENCE OF  
    WfIisisAreaEntry

wfIisisAreaEntry 1.3.6.1.4.1.18.3.5.3.2.8.2.1
'Information describing the configured parameters and cumulative statistics of one of the router's attached areas.'
OBJECT-TYPE    
  WfIisisAreaEntry  

wfIisisAreaDelete 1.3.6.1.4.1.18.3.5.3.2.8.2.1.1
This value determines if the I-ISIS router is configured with this area.
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfIisisAreaDisable 1.3.6.1.4.1.18.3.5.3.2.8.2.1.2
This value indicates the state of this area on the I-ISIS router.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfIisisAreaState 1.3.6.1.4.1.18.3.5.3.2.8.2.1.3
This value indicates the state of the I-ISIS Area.
OBJECT-TYPE    
  INTEGER up(1), down(2)  

wfIisisAreaId 1.3.6.1.4.1.18.3.5.3.2.8.2.1.4
A 32-bit integer uniquely identifying an area. Area ID 0.0.0.0 is used for the I-ISIS backbone.
OBJECT-TYPE    
  IpAddress  

wfIisisSpfCnt 1.3.6.1.4.1.18.3.5.3.2.8.2.1.5
The number of times the I-ISIS SPF algorithm has been run for this area.
OBJECT-TYPE    
  Counter  

wfIisisL1LspHdrTable 1.3.6.1.4.1.18.3.5.3.2.8.3
2 u_int32's so the inst_id len is 2.
OBJECT-TYPE    
  SEQUENCE OF  
    WfIisisL1LspHdrEntry

wfIisisL1LspHdrEntry 1.3.6.1.4.1.18.3.5.3.2.8.3.1
A Record in the Level 1 Lsp Header Table
OBJECT-TYPE    
  WfIisisL1LspHdrEntry  

wfIisisL1LspHdrLspId 1.3.6.1.4.1.18.3.5.3.2.8.3.1.1
LSPID = Source ID + Pseudo-node ID + LSP number
OBJECT-TYPE    
  OCTET STRING SIZE(8)  

wfIisisL1LspHdrLifetime 1.3.6.1.4.1.18.3.5.3.2.8.3.1.2
Lsp Lifetime
OBJECT-TYPE    
  INTEGER  

wfIisisL1LspHdrSeqnum 1.3.6.1.4.1.18.3.5.3.2.8.3.1.3
Lsp sequence number
OBJECT-TYPE    
  INTEGER  

wfIisisL1LspHdrFlags 1.3.6.1.4.1.18.3.5.3.2.8.3.1.4
Flags: P/ATT/LSPDBOL/IS type
OBJECT-TYPE    
  INTEGER  

wfIisisL1LspHdrCksum 1.3.6.1.4.1.18.3.5.3.2.8.3.1.5
Checksum
OBJECT-TYPE    
  OCTET STRING  

wfIisisL2LspHdrTable 1.3.6.1.4.1.18.3.5.3.2.8.4
2 u_int32's so the inst_id len is 2.
OBJECT-TYPE    
  SEQUENCE OF  
    WfIisisL2LspHdrEntry

wfIisisL2LspHdrEntry 1.3.6.1.4.1.18.3.5.3.2.8.4.1
A Record in the Lsp Header Table
OBJECT-TYPE    
  WfIisisL2LspHdrEntry  

wfIisisL2LspHdrLspId 1.3.6.1.4.1.18.3.5.3.2.8.4.1.1
LSPID = Source ID + Pseudo-node ID + LSP number
OBJECT-TYPE    
  OCTET STRING SIZE(8)  

wfIisisL2LspHdrLifetime 1.3.6.1.4.1.18.3.5.3.2.8.4.1.2
Lsp Lifetime
OBJECT-TYPE    
  INTEGER  

wfIisisL2LspHdrSeqnum 1.3.6.1.4.1.18.3.5.3.2.8.4.1.3
Lsp sequence number
OBJECT-TYPE    
  INTEGER  

wfIisisL2LspHdrFlags 1.3.6.1.4.1.18.3.5.3.2.8.4.1.4
Flags: P/ATT/LSPDBOL/IS type
OBJECT-TYPE    
  INTEGER  

wfIisisL2LspHdrCksum 1.3.6.1.4.1.18.3.5.3.2.8.4.1.5
Checksum
OBJECT-TYPE    
  OCTET STRING  

wfIisisIfTable 1.3.6.1.4.1.18.3.5.3.2.8.5
-- I-ISIS Interface Table -- The I-ISIS Interface Table augments the ifTable with I-ISIS -- specific information. 'The I-ISIS Interface Table describes the interfaces from the viewpoint of I-ISIS.'
OBJECT-TYPE    
  SEQUENCE OF  
    WfIisisIfEntry

wfIisisIfEntry 1.3.6.1.4.1.18.3.5.3.2.8.5.1
'The I-ISIS Interface Entry describes one interface from the viewpoint of I-ISIS.'
OBJECT-TYPE    
  WfIisisIfEntry  

wfIisisIfDelete 1.3.6.1.4.1.18.3.5.3.2.8.5.1.1
This variable determines in an I-ISIS Interface has been configured on the router.
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfIisisIfDisable 1.3.6.1.4.1.18.3.5.3.2.8.5.1.2
'The I-ISIS interface's administrative status. The value 'enabled' denotes that neighbor relationships may be formed on the interface, and the interface will be advertised as an internal route to some area. The value 'disabled' denotes that the interface is external to I-ISIS.'
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfIisisIfIpAddress 1.3.6.1.4.1.18.3.5.3.2.8.5.1.3
'The IP address of this I-ISIS interface.'
OBJECT-TYPE    
  IpAddress  

wfIisisAddressLessIf 1.3.6.1.4.1.18.3.5.3.2.8.5.1.4
'For the purpose of easing the instancing of addressed and addressless interfaces; This variable takes the value 0 on interfaces with IP Addresses, and the corresponding value of ifIndex for interfaces having no IP Address.'
OBJECT-TYPE    
  INTEGER  

wfIisisIfRouterLevel 1.3.6.1.4.1.18.3.5.3.2.8.5.1.5
This is the level protocol that the circuit runs. Its a bit mask to allow for some combination of L1, L2, External, ES-IS-only.
OBJECT-TYPE    
  INTEGER l1(1), l2(2), l1l2(3), ext(4), l2ext(6), l1l2ext(7), esisonly(8)  

wfIisisIfL1DefaultMetric 1.3.6.1.4.1.18.3.5.3.2.8.5.1.6
This is the default cost of using this circuit for L1 traffic.
OBJECT-TYPE    
  INTEGER 1..63  

wfIisisIfL2DefaultMetric 1.3.6.1.4.1.18.3.5.3.2.8.5.1.7
This is the default cost of using this circuit for L2 traffic.
OBJECT-TYPE    
  INTEGER 1..63  

wfIisisIfL1DrPriority 1.3.6.1.4.1.18.3.5.3.2.8.5.1.8
This is the priority for this system to become L1 designated router on this LAN circuit.
OBJECT-TYPE    
  INTEGER 1..127  

wfIisisIfL2DrPriority 1.3.6.1.4.1.18.3.5.3.2.8.5.1.9
This is the priority for this system to become L2 designated router on this LAN circuit.
OBJECT-TYPE    
  INTEGER 1..127  

wfIisisIfHelloTimer 1.3.6.1.4.1.18.3.5.3.2.8.5.1.10
This is the period (secs) between IIH hello transmissions.
OBJECT-TYPE    
  INTEGER 1..21845  

wfIisisIfPassword 1.3.6.1.4.1.18.3.5.3.2.8.5.1.11
This is Circuit Password for this circuit. Used to filter out Hellos from systems without the correct password.
OBJECT-TYPE    
  DisplayString  

wfIisisIfHelloMtuSize 1.3.6.1.4.1.18.3.5.3.2.8.5.1.12
Configure Hello MTU size per I-ISIS interface This parameter has the following values/meanings: 1 - Use the MTU specified by IP 2 - Use the MTU of ethernet, regardless of what IP says > 2 - Use this value as the actual MTU. If the value is smaller than what I-ISIS needs as a minimum then the mtu specified by IP is used. For example, 3 would never be used as an MTU.
OBJECT-TYPE    
  INTEGER 1..10000  

wfIisisIfIihHoldMultiplier 1.3.6.1.4.1.18.3.5.3.2.8.5.1.13
This is the multiplier value used to compute the hold time set in the IIH PDUs transmitted from this router. Hold time equals IIH Timer times IIH Hold Multiplier.
OBJECT-TYPE    
  INTEGER 1..5  

wfIisisIfIshHoldMultiplier 1.3.6.1.4.1.18.3.5.3.2.8.5.1.14
This is the multiplier value used to compute the hold time set in the ISH PDUs transmitted from this router. Hold time equals IIH Timer times IIH Hold Multiplier.
OBJECT-TYPE    
  INTEGER 1..5  

wfIisisIfType 1.3.6.1.4.1.18.3.5.3.2.8.5.1.15
The IISIS interface type.
OBJECT-TYPE    
  INTEGER broadcast(1), pointtopoint(2)  

wfIisisIfCsnpTimer 1.3.6.1.4.1.18.3.5.3.2.8.5.1.16
This is the period (in seconds) between CSNP transmissions.
OBJECT-TYPE    
  INTEGER 10..600  

wfIisisIfStatsTable 1.3.6.1.4.1.18.3.5.3.2.8.6
-- I-ISIS Interface Stats Table.
OBJECT-TYPE    
  SEQUENCE OF  
    WfIisisIfStatsEntry

wfIisisIfStatsEntry 1.3.6.1.4.1.18.3.5.3.2.8.6.1
'The information regarding a interface'.
OBJECT-TYPE    
  WfIisisIfStatsEntry  

wfIisisIfStatsIpAddress 1.3.6.1.4.1.18.3.5.3.2.8.6.1.1
'The IP address of this I-ISIS interface.'
OBJECT-TYPE    
  IpAddress  

wfIisisStatsAddressLessIf 1.3.6.1.4.1.18.3.5.3.2.8.6.1.2
'For the purpose of easing the instancing of addressed and addressless interfaces; This variable takes the value 0 on interfaces with IP Addresses, and the corresponding value of ifIndex for interfaces having no IP Address.'
OBJECT-TYPE    
  INTEGER  

wfIisisIfStatsState 1.3.6.1.4.1.18.3.5.3.2.8.6.1.3
This indicates whether the circuit state is up or down.
OBJECT-TYPE    
  INTEGER up(1), down(2)  

wfIisisIfStatsCct 1.3.6.1.4.1.18.3.5.3.2.8.6.1.4
A unique value for each known circuit.
OBJECT-TYPE    
  INTEGER  

wfIisisIfStatsL1TxHellos 1.3.6.1.4.1.18.3.5.3.2.8.6.1.5
Number of I-ISIS Hello packets transmitted.
OBJECT-TYPE    
  Counter  

wfIisisIfStatsL2TxHellos 1.3.6.1.4.1.18.3.5.3.2.8.6.1.6
Number of I-ISIS Hello packets transmitted.
OBJECT-TYPE    
  Counter  

wfIisisIfStatsL1RxHellos 1.3.6.1.4.1.18.3.5.3.2.8.6.1.7
Number of I-ISIS Hello packets received.
OBJECT-TYPE    
  Counter  

wfIisisIfStatsL2RxHellos 1.3.6.1.4.1.18.3.5.3.2.8.6.1.8
Number of I-ISIS Hello packets received.
OBJECT-TYPE    
  Counter  

wfIisisIfStatsL1Drops 1.3.6.1.4.1.18.3.5.3.2.8.6.1.9
Number of I-ISIS packets dropped because of invalid information in the packet.
OBJECT-TYPE    
  Counter  

wfIisisIfStatsL2Drops 1.3.6.1.4.1.18.3.5.3.2.8.6.1.10
Number of I-ISIS packets dropped because of invalid information in the packet.
OBJECT-TYPE    
  Counter  

wfIisisIfStatsL1DesignatedRouter 1.3.6.1.4.1.18.3.5.3.2.8.6.1.11
This is the ID of the L1 Designated Router on this circuit.
OBJECT-TYPE    
  OCTET STRING  

wfIisisIfStatsL2DesignatedRouter 1.3.6.1.4.1.18.3.5.3.2.8.6.1.12
This is the ID of the L2 Designated Router on this circuit.
OBJECT-TYPE    
  OCTET STRING  

wfIisisIfStatsTxL1Lsp 1.3.6.1.4.1.18.3.5.3.2.8.6.1.13
Number of L1 LSPs(Link State Packet) transmitted.
OBJECT-TYPE    
  Counter  

wfIisisIfStatsTxL2Lsp 1.3.6.1.4.1.18.3.5.3.2.8.6.1.14
Number of L2 LSPs(Link State Packet) transmitted.
OBJECT-TYPE    
  Counter  

wfIisisIfStatsTxL1Csnp 1.3.6.1.4.1.18.3.5.3.2.8.6.1.15
Number of L1 CSNPs(Complete sequence no. packet) transmitted.
OBJECT-TYPE    
  Counter  

wfIisisIfStatsTxL2Csnp 1.3.6.1.4.1.18.3.5.3.2.8.6.1.16
Number of L2 CSNPs(Complete sequence no. packet) transmitted.
OBJECT-TYPE    
  Counter  

wfIisisIfStatsTxL1Psnp 1.3.6.1.4.1.18.3.5.3.2.8.6.1.17
Number of L1 PSNPs(Partial sequence no. packet) transmitted.
OBJECT-TYPE    
  Counter  

wfIisisIfStatsTxL2Psnp 1.3.6.1.4.1.18.3.5.3.2.8.6.1.18
Number of L2 PSNPs(Partial sequence no. packet) transmitted.
OBJECT-TYPE    
  Counter  

wfIisisIfStatsRxL1Lsp 1.3.6.1.4.1.18.3.5.3.2.8.6.1.19
Number of L1 LSPs(Link State Packet) received.
OBJECT-TYPE    
  Counter  

wfIisisIfStatsRxL2Lsp 1.3.6.1.4.1.18.3.5.3.2.8.6.1.20
Number of L2 LSPs(Link State Packet) received.
OBJECT-TYPE    
  Counter  

wfIisisIfStatsRxL1Csnp 1.3.6.1.4.1.18.3.5.3.2.8.6.1.21
Number of L1 CSNPs(Complete sequence no. packet) received.
OBJECT-TYPE    
  Counter  

wfIisisIfStatsRxL2Csnp 1.3.6.1.4.1.18.3.5.3.2.8.6.1.22
Number of L2 CSNPs(Complete sequence no. packet) received.
OBJECT-TYPE    
  Counter  

wfIisisIfStatsRxL1Psnp 1.3.6.1.4.1.18.3.5.3.2.8.6.1.23
Number of L1 PSNPs(Partial sequence no. packet) received.
OBJECT-TYPE    
  Counter  

wfIisisIfStatsRxL2Psnp 1.3.6.1.4.1.18.3.5.3.2.8.6.1.24
Number of L2 PSNPs(Partial sequence no. packet) received.
OBJECT-TYPE    
  Counter  

wfIisisIfStatsL1NbrCount 1.3.6.1.4.1.18.3.5.3.2.8.6.1.25
Count of neighbors with any state.
OBJECT-TYPE    
  Gauge  

wfIisisIfStatsL2NbrCount 1.3.6.1.4.1.18.3.5.3.2.8.6.1.26
Count of neighbors with any state.
OBJECT-TYPE    
  Gauge  

wfIisisIfStatsL1AdjCount 1.3.6.1.4.1.18.3.5.3.2.8.6.1.27
Count of neighbors with state UP.
OBJECT-TYPE    
  Gauge  

wfIisisIfStatsL2AdjCount 1.3.6.1.4.1.18.3.5.3.2.8.6.1.28
Count of neighbors with state UP.
OBJECT-TYPE    
  Gauge  

wfIisisDynNbrTable 1.3.6.1.4.1.18.3.5.3.2.8.7
-- I-ISIS Dynamic Neighbor Table The I-ISIS Dynamic Neighbor Table describes all neighbors in the locality of the subject router learned during operation.
OBJECT-TYPE    
  SEQUENCE OF  
    WfIisisDynNbrEntry

wfIisisDynNbrEntry 1.3.6.1.4.1.18.3.5.3.2.8.7.1
'The information regarding a single neighbor.' REFERENCE 'I-ISIS Version 2, Section 10 The Neighbor Data Structure'
OBJECT-TYPE    
  WfIisisDynNbrEntry  

wfIisisDynNbrState 1.3.6.1.4.1.18.3.5.3.2.8.7.1.1
'The State of the relationship with this Neighbor.'
OBJECT-TYPE    
  INTEGER down(1), init(2), up(3)  

wfIisisDynNbrIpAddr 1.3.6.1.4.1.18.3.5.3.2.8.7.1.2
'The IP address of this neighbor.'
OBJECT-TYPE    
  IpAddress  

wfIisisDynNbrIfAddr 1.3.6.1.4.1.18.3.5.3.2.8.7.1.3
'Our Interface IP address for this neighbor.'
OBJECT-TYPE    
  IpAddress  

wfIisisDynNbrAddressLessIndex 1.3.6.1.4.1.18.3.5.3.2.8.7.1.4
'The circuit over which this neighbor is learnt.'
OBJECT-TYPE    
  INTEGER  

wfIisisDynNbrRtrId 1.3.6.1.4.1.18.3.5.3.2.8.7.1.5
'A 6 byte field representing the Intermediate system Id.'
OBJECT-TYPE    
  OCTET STRING  

wfIisisDynNbrDatabase 1.3.6.1.4.1.18.3.5.3.2.8.7.1.6
Database into which the Adjacency is stored, 1=ES, 2=Level 1 IS, 3=Level 2 IS.
OBJECT-TYPE    
  INTEGER  

wfIisisDynNbrType 1.3.6.1.4.1.18.3.5.3.2.8.7.1.7
The type of adjacency.
OBJECT-TYPE    
  INTEGER broadcast(1), pointtopoint(2)  

wfIisisDynNbrPseudonodeId 1.3.6.1.4.1.18.3.5.3.2.8.7.1.8
A unique value for each known circuit.
OBJECT-TYPE    
  INTEGER  

wfIisisDynNbrHoldTime 1.3.6.1.4.1.18.3.5.3.2.8.7.1.9
Hold Time received from neighbor.
OBJECT-TYPE    
  INTEGER  

wfIisisDynNbrPriority 1.3.6.1.4.1.18.3.5.3.2.8.7.1.10
Priority to become designated router. IS only.
OBJECT-TYPE    
  INTEGER  

wfIisisDynNbrSnpaAddr 1.3.6.1.4.1.18.3.5.3.2.8.7.1.11
SNPA address for neighbor.
OBJECT-TYPE    
  OCTET STRING  

wfIisisDynNbrLanId 1.3.6.1.4.1.18.3.5.3.2.8.7.1.12
LAN ID of Designated IS of this interface.
OBJECT-TYPE    
  OCTET STRING  

Defined Objects

WfIisisAreaEntry  
SEQUENCE    
  INTEGER as wfIisisAreaDelete  
  INTEGER as wfIisisAreaDisable  
  INTEGER as wfIisisAreaState  
  IpAddress as wfIisisAreaId  
  Counter as wfIisisSpfCnt  

WfIisisL1LspHdrEntry  
SEQUENCE    
  OCTET STRING as wfIisisL1LspHdrLspId  
  INTEGER as wfIisisL1LspHdrLifetime  
  INTEGER as wfIisisL1LspHdrSeqnum  
  INTEGER as wfIisisL1LspHdrFlags  
  OCTET STRING as wfIisisL1LspHdrCksum  

WfIisisL2LspHdrEntry  
SEQUENCE    
  OCTET STRING as wfIisisL2LspHdrLspId  
  INTEGER as wfIisisL2LspHdrLifetime  
  INTEGER as wfIisisL2LspHdrSeqnum  
  INTEGER as wfIisisL2LspHdrFlags  
  OCTET STRING as wfIisisL2LspHdrCksum  

WfIisisIfEntry  
SEQUENCE    
  INTEGER as wfIisisIfDelete  
  INTEGER as wfIisisIfDisable  
  IpAddress as wfIisisIfIpAddress  
  INTEGER as wfIisisAddressLessIf  
  INTEGER as wfIisisIfRouterLevel  
  INTEGER as wfIisisIfL1DefaultMetric  
  INTEGER as wfIisisIfL2DefaultMetric  
  INTEGER as wfIisisIfL1DrPriority  
  INTEGER as wfIisisIfL2DrPriority  
  INTEGER as wfIisisIfHelloTimer  
  DisplayString as wfIisisIfPassword  
  INTEGER as wfIisisIfHelloMtuSize  
  INTEGER as wfIisisIfIihHoldMultiplier  
  INTEGER as wfIisisIfIshHoldMultiplier  
  INTEGER as wfIisisIfType  
  INTEGER as wfIisisIfCsnpTimer  

WfIisisIfStatsEntry  
SEQUENCE    
  IpAddress as wfIisisIfStatsIpAddress  
  INTEGER as wfIisisStatsAddressLessIf  
  INTEGER as wfIisisIfStatsState  
  INTEGER as wfIisisIfStatsCct  
  Counter as wfIisisIfStatsL1TxHellos  
  Counter as wfIisisIfStatsL2TxHellos  
  Counter as wfIisisIfStatsL1RxHellos  
  Counter as wfIisisIfStatsL2RxHellos  
  Counter as wfIisisIfStatsL1Drops  
  Counter as wfIisisIfStatsL2Drops  
  OCTET STRING as wfIisisIfStatsL1DesignatedRouter  
  OCTET STRING as wfIisisIfStatsL2DesignatedRouter  
  Counter as wfIisisIfStatsTxL1Lsp  
  Counter as wfIisisIfStatsTxL2Lsp  
  Counter as wfIisisIfStatsTxL1Csnp  
  Counter as wfIisisIfStatsTxL2Csnp  
  Counter as wfIisisIfStatsTxL1Psnp  
  Counter as wfIisisIfStatsTxL2Psnp  
  Counter as wfIisisIfStatsRxL1Lsp  
  Counter as wfIisisIfStatsRxL2Lsp  
  Counter as wfIisisIfStatsRxL1Csnp  
  Counter as wfIisisIfStatsRxL2Csnp  
  Counter as wfIisisIfStatsRxL1Psnp  
  Counter as wfIisisIfStatsRxL2Psnp  
  Gauge as wfIisisIfStatsL1NbrCount  
  Gauge as wfIisisIfStatsL2NbrCount  
  Gauge as wfIisisIfStatsL1AdjCount  
  Gauge as wfIisisIfStatsL2AdjCount  

WfIisisDynNbrEntry  
SEQUENCE    
  INTEGER as wfIisisDynNbrState  
  IpAddress as wfIisisDynNbrIpAddr  
  IpAddress as wfIisisDynNbrIfAddr  
  INTEGER as wfIisisDynNbrAddressLessIndex  
  OCTET STRING as wfIisisDynNbrRtrId  
  INTEGER as wfIisisDynNbrDatabase  
  INTEGER as wfIisisDynNbrType  
  INTEGER as wfIisisDynNbrPseudonodeId  
  INTEGER as wfIisisDynNbrHoldTime  
  INTEGER as wfIisisDynNbrPriority  
  OCTET STRING as wfIisisDynNbrSnpaAddr  
  OCTET STRING as wfIisisDynNbrLanId