CASCADE-MIB

File: CASCADE-MIB.mib (475199 bytes)

Imported modules

RFC1155-SMI RFC1213-MIB RFC-1212
RFC-1215

Imported symbols

enterprises IpAddress Counter
Gauge TimeTicks DisplayString
ifInErrors OBJECT-TYPE TRAP-TYPE

Defined Objects

cascade 1.3.6.1.4.1.277
OBJECT IDENTIFIER    

cascfr 1.3.6.1.4.1.277.1
OBJECT IDENTIFIER    

net 1.3.6.1.4.1.277.1.1
OBJECT IDENTIFIER    

nodeBoardInserted 1.3.6.1.4.1.277.1.1
This trap indicates that a board has been inserted into the indicated slot.
TRAP-TYPE    
  pportSlotId  
  pportType  

netMask 1.3.6.1.4.1.277.1.1.1
The IP subnet mask for the network. The default is 255.255.255.0 (class C) which allows 254 nodes.
OBJECT-TYPE    
  IpAddress  

netNumber 1.3.6.1.4.1.277.1.1.2
The IP network number for the network.
OBJECT-TYPE    
  IpAddress  

netDlciAddrSig 1.3.6.1.4.1.277.1.1.3
This variable states the DLCI addressing significance.
OBJECT-TYPE    
  INTEGER globalAddr(1), localAddr(2)  

netMaxSegsize 1.3.6.1.4.1.277.1.1.4
This variable states the maximum sgement size for the network.
OBJECT-TYPE    
  INTEGER  

netSmdsAreaMaskStart 1.3.6.1.4.1.277.1.1.8
This variable states the starting digit number for defining the start of the Area Mask for SMDS Addresses.
OBJECT-TYPE    
  INTEGER  

netSmdsAreaMaskDigits 1.3.6.1.4.1.277.1.1.9
This variable states the number of digits used for defining the Area Mask for SMDS Addresses.
OBJECT-TYPE    
  INTEGER  

ase 1.3.6.1.4.1.277.1.2
OBJECT IDENTIFIER    

nodeBoardPulled 1.3.6.1.4.1.277.1.2
This trap indicates that a board has been pulled out from the indicated slot.
TRAP-TYPE    
  pportSlotId  
  pportType  

aseTable 1.3.6.1.4.1.277.1.2.1
A list of ASE entries.
OBJECT-TYPE    
  SEQUENCE OF  
    AseEntry

aseEntry 1.3.6.1.4.1.277.1.2.1.1
An ASE entry contains an external NMS path accessible from the node.
OBJECT-TYPE    
  AseEntry  

aseAddr 1.3.6.1.4.1.277.1.2.1.1.1
IP Address for an external NMS.
OBJECT-TYPE    
  IpAddress  

aseMask 1.3.6.1.4.1.277.1.2.1.1.2
IP Address mask for an external NMS. The default value is 255.255.255.255.
OBJECT-TYPE    
  IpAddress  

aseDefaultGwAddr 1.3.6.1.4.1.277.1.2.1.1.3
Default Gateway IP Address for reaching the external NMS. This field is not applicable to NMSs which are reachable via SLIP or on the same Ethernet.
OBJECT-TYPE    
  IpAddress  

aseMetricType 1.3.6.1.4.1.277.1.2.1.1.4
Type of metric (1 or 2) for each external NMS. The default is 1. (This field is not applicable to SLIP- based hosts.)
OBJECT-TYPE    
  INTEGER  

aseAdminStatus 1.3.6.1.4.1.277.1.2.1.1.5
The desired state of the entry.
OBJECT-TYPE    
  INTEGER valid(1)  

aseIfIndex 1.3.6.1.4.1.277.1.2.1.1.6
The interface value of the corresponding MIB-II ifEntry.
OBJECT-TYPE    
  Index  

aseDlci 1.3.6.1.4.1.277.1.2.1.1.7
The management dlci through which the NMS communicates to the switch.
OBJECT-TYPE    
  INTEGER  

node 1.3.6.1.4.1.277.1.3
OBJECT IDENTIFIER    

nodeBoardMismatch 1.3.6.1.4.1.277.1.3
This trap indicates that the actual board type on the indicated slot is inconsistent with what is configured.
TRAP-TYPE    
  pportSlotId  
  pportType  

nodeIpAddr 1.3.6.1.4.1.277.1.3.1
The inband IP address of the node in the Cascade internal trunk IP network.
OBJECT-TYPE    
  IpAddress  

nodeLanIpAddr 1.3.6.1.4.1.277.1.3.2
The inband (Ethernet) IP address of the node for a NMS to access the node and the internal trunk IP network.
OBJECT-TYPE    
  IpAddress  

nodeNMSTable 1.3.6.1.4.1.277.1.3.3
A list of NMS entries.
OBJECT-TYPE    
  SEQUENCE OF  
    NodeNMSEntry

nodeNMSEntry 1.3.6.1.4.1.277.1.3.3.1
A NMS entry contains an IP address of a NMS which has extended privilages.
OBJECT-TYPE    
  NodeNMSEntry  

nodeNMSIndex 1.3.6.1.4.1.277.1.3.3.1.1
The IP address entry of a primary Network Management Station.
OBJECT-TYPE    
  Index  

nodeNMSIpAddr 1.3.6.1.4.1.277.1.3.3.1.2
The IP address of the primary Network Management Station. It is to this address that Traps and TFTP requests will be directed.
OBJECT-TYPE    
  IpAddress  

nodeState 1.3.6.1.4.1.277.1.3.4
The state of the switch. The switch needs to await the state to be set to active before being fully operational after cold boot, when the NMS is reachable.
OBJECT-TYPE    
  INTEGER down(1), initializing(2), active(3), marginal(4), testing(5)  

nodePollStatus 1.3.6.1.4.1.277.1.3.5
The consolidated node status in response to keep-alive polls. It is an octet string of a proprietary format
OBJECT-TYPE    
  OCTET STRING  

nodeModel 1.3.6.1.4.1.277.1.3.6
The part number of the node.
OBJECT-TYPE    
  DisplayString  

nodeSerial 1.3.6.1.4.1.277.1.3.7
The serial number (i.e., Ethernet Addr) of the switch.
OBJECT-TYPE    
  OCTET STRING  

nodeSwRev 1.3.6.1.4.1.277.1.3.8
The software revision number (major.minor).
OBJECT-TYPE    
  DisplayString  

nodeHwRev 1.3.6.1.4.1.277.1.3.9
The hardware revision number (major.minor).
OBJECT-TYPE    
  DisplayString  

nodeEpromRev 1.3.6.1.4.1.277.1.3.10
The EPROM firmware revision number (major.minor).
OBJECT-TYPE    
  DisplayString  

nodeCpuUtil 1.3.6.1.4.1.277.1.3.11
The CPU utilization percentage for packet processing.
OBJECT-TYPE    
  Gauge  

nodePsAStatus 1.3.6.1.4.1.277.1.3.12
The status of the power supply A. For a detailed explanation for the power supply being either in the down or marginal state, refer to the nodePsADiagCode object.
OBJECT-TYPE    
  INTEGER up(1), down(2), marginal(4)  

nodePsBStatus 1.3.6.1.4.1.277.1.3.13
The status of the power supply B. For a detailed explanation for the power supply being either in the down or marginal state, refer to the nodePsBDiagCode object.
OBJECT-TYPE    
  INTEGER up(1), down(2), marginal(4)  

nodeFanTable 1.3.6.1.4.1.277.1.3.14
A list of fan entries.
OBJECT-TYPE    
  SEQUENCE OF  
    NodeFanEntry

nodeFanEntry 1.3.6.1.4.1.277.1.3.14.1
A Fan entry contains the status of a fan.
OBJECT-TYPE    
  NodeFanEntry  

nodeFanIndex 1.3.6.1.4.1.277.1.3.14.1.1
A unique value for each fan.
OBJECT-TYPE    
  INTEGER  

nodeFanStatus 1.3.6.1.4.1.277.1.3.14.1.2
The status of the fan.
OBJECT-TYPE    
  INTEGER up(1), down(2), marginal(3)  

nodeFanSpeed 1.3.6.1.4.1.277.1.3.14.1.3
The speed in Revolutions Per. Minute (RPM) of the fan.
OBJECT-TYPE    
  Gauge  

nodeMemoryUtil 1.3.6.1.4.1.277.1.3.15
The percentage of system memory utilization on this intelligent card.
OBJECT-TYPE    
  Gauge  

nodeMemoryUsage 1.3.6.1.4.1.277.1.3.16
The system memory utilization, in terms of free bytes, for this intelligent card.
OBJECT-TYPE    
  Gauge  

nodeMaxFramesize 1.3.6.1.4.1.277.1.3.17
The maximum frame size supported by the node. The default is 4096.
OBJECT-TYPE    
  INTEGER  

nodeQOSPollTimer 1.3.6.1.4.1.277.1.3.18
The timer (seconds) for generating QOS polling packets.
OBJECT-TYPE    
  INTEGER  

nodeActivePvcs 1.3.6.1.4.1.277.1.3.19
The number of currently active PVCs on the node.
OBJECT-TYPE    
  Counter  

nodeInactivePvcs 1.3.6.1.4.1.277.1.3.20
The number of currently inactive PVCs on the node.
OBJECT-TYPE    
  Counter  

nodePendingPvcs 1.3.6.1.4.1.277.1.3.21
The number of currently call pending PVCs on the node.
OBJECT-TYPE    
  Counter  

nodeInOctets 1.3.6.1.4.1.277.1.3.22
The total number of octets received on the node, including framing bytes.
OBJECT-TYPE    
  Counter  

nodeInPkts 1.3.6.1.4.1.277.1.3.23
The total number of packets received on the node.
OBJECT-TYPE    
  Counter  

nodeOutOctets 1.3.6.1.4.1.277.1.3.24
The total number of octets transmitted out of the node, including framing bytes.
OBJECT-TYPE    
  Counter  

nodeOutPkts 1.3.6.1.4.1.277.1.3.25
The total number of packets requested to be transmitted out of the node, including those that were discarded or not sent.
OBJECT-TYPE    
  Counter  

nodeSwFilename 1.3.6.1.4.1.277.1.3.26
Name of the file to be downloaded.
OBJECT-TYPE    
  DisplayString  

nodeRebootAfterLoad 1.3.6.1.4.1.277.1.3.27
Instructs the device to either automatically reboot after the successful scheduled download or not.
OBJECT-TYPE    
  INTEGER reboot(1)  

nodeSwToLoad 1.3.6.1.4.1.277.1.3.28
Instructs the device to initiate a software download (via tftp) request to the master management station after the specified time ticks have elapsed.
OBJECT-TYPE    
  TimeTicks  

nodeSwLoadState 1.3.6.1.4.1.277.1.3.29
The state of the software download request. A download which is in either the PENDING, ACTIVE or FAILED state can be terminated by setting this object to INACTIVE.
OBJECT-TYPE    
  INTEGER inactive(1), pending(2), active(3), failed(4)  

nodePrFilename 1.3.6.1.4.1.277.1.3.30
Name of the PRAM image file to be downloaded.
OBJECT-TYPE    
  DisplayString  

nodePrToLoad 1.3.6.1.4.1.277.1.3.31
Instructs the device to initiate a PRAM image file download (via tftp) request to the master management station after the specified time ticks have elapsed.
OBJECT-TYPE    
  TimeTicks  

nodePrLoadState 1.3.6.1.4.1.277.1.3.32
The state of the PRAM download request. A download which is in either the PENDING, ACTIVE or FAILED state can be terminated by setting this object to INACTIVE.
OBJECT-TYPE    
  INTEGER inactive(1), pending(2), active(3), failed(4)  

nodeToWarmboot 1.3.6.1.4.1.277.1.3.33
Instructs the switch to initiate a system warm boot after the specified time ticks have elapsed. A value of 0 indicates cancellation of the previously scheduled re-boot request.
OBJECT-TYPE    
  TimeTicks  

nodeToColdboot 1.3.6.1.4.1.277.1.3.34
Instructs the switch to initiate a system cold boot after the specified time ticks have elapsed. A value of 0 indicates cancellation of the previously scheduled re-boot request.
OBJECT-TYPE    
  TimeTicks  

nodeToRedundant 1.3.6.1.4.1.277.1.3.35
If redundancy is configured, instructs the node acting as Backup to disable the Active node and take over as the Active node. The disabling is initiated after the specified time ticks have elapsed. A value of 0 indicates cancellation of the previously scheduled request.
OBJECT-TYPE    
  TimeTicks  

nodeInitiateBulkStats 1.3.6.1.4.1.277.1.3.36
Initiates a Bulk Statistics poll and via TFTP, transfer the data to the specified IP address.
OBJECT-TYPE    
  IpAddress  

nodeDiagNonFatalSource 1.3.6.1.4.1.277.1.3.37
Source who reported last non-fatal error.
OBJECT-TYPE    
  INTEGER power-on-diagnostics(1), background-diagnostics(2), fault(3), frame-heap(4)  

nodeDiagNonFatalTime 1.3.6.1.4.1.277.1.3.38
Time the last non-fatal error was reported.
OBJECT-TYPE    
  TimeTicks  

nodeDiagNonFatalErrMajor 1.3.6.1.4.1.277.1.3.39
Major error code of last non-fatal error.
OBJECT-TYPE    
  INTEGER  

nodeDiagNonFatalErrMinor 1.3.6.1.4.1.277.1.3.40
Minor error code of last non-fatal error.
OBJECT-TYPE    
  INTEGER  

nodeDiagNonFatalStr 1.3.6.1.4.1.277.1.3.41
Ascii string describing last non-fatal error.
OBJECT-TYPE    
  DisplayString  

nodeDiagFatalSource 1.3.6.1.4.1.277.1.3.42
Source who reported last fatal error.
OBJECT-TYPE    
  INTEGER power-on-diagnostics(1), background-diagnostics(2), fault(3), frame-heap(4)  

nodeDiagFatalTime 1.3.6.1.4.1.277.1.3.43
Time the last fatal error was reported.
OBJECT-TYPE    
  TimeTicks  

nodeDiagFatalErrMajor 1.3.6.1.4.1.277.1.3.44
Major error code of last fatal error.
OBJECT-TYPE    
  INTEGER  

nodeDiagFatalErrMinor 1.3.6.1.4.1.277.1.3.45
Minor error code of last fatal error.
OBJECT-TYPE    
  INTEGER  

nodeDiagFatalStr 1.3.6.1.4.1.277.1.3.46
Ascii string describing last fatal error.
OBJECT-TYPE    
  DisplayString  

nodeDiagFatalReboots 1.3.6.1.4.1.277.1.3.47
Number of times the switch has re-booted since last fatal error was reported.
OBJECT-TYPE    
  Counter  

nodeDiagFatalAddress 1.3.6.1.4.1.277.1.3.48
Address switch was executing when it encountered fatal error.
OBJECT-TYPE    
  INTEGER  

nodeDiagBackgroundPasses 1.3.6.1.4.1.277.1.3.49
Number of passes made by the background diagnostics.
OBJECT-TYPE    
  Counter  

nodeDiagBackgroundFailures 1.3.6.1.4.1.277.1.3.50
Number of failures discovered by background diagnostics.
OBJECT-TYPE    
  Counter  

nodeDiagBackgroundSuccesses 1.3.6.1.4.1.277.1.3.51
Number of successful passes by background diagnostics.
OBJECT-TYPE    
  Counter  

nodeDiagLEDReset 1.3.6.1.4.1.277.1.3.52
Change the node state from marginal to active. Change the LED from yellow to green.
OBJECT-TYPE    
  INTEGER state-to-active(1)  

nodeDiagPowerExtensive 1.3.6.1.4.1.277.1.3.53
Should power on diagnostics do slower, extensive testing, or fast testing?
OBJECT-TYPE    
  INTEGER extensive-tests(1)  

nodePortPoll 1.3.6.1.4.1.277.1.3.54
The consolidated port status in response to keep-alive polls.
OBJECT-TYPE    
  OCTET STRING  

nodeMaxTelnetConsole 1.3.6.1.4.1.277.1.3.55
The number of concurrent telnet consoles allowed. The default is 2. The maximum is 5. Set it 0 to disable telnet access.
OBJECT-TYPE    
  INTEGER  

nodeConsoleTimeout 1.3.6.1.4.1.277.1.3.56
Idle-logoff timer in minutes. The default is 5 minutes, and the maximum can be set is 60 minutes. To disable idle-logout, set this to 0.
OBJECT-TYPE    
  INTEGER  

nodeConsoleTable 1.3.6.1.4.1.277.1.3.57
A list of active consoles on the node, logged in through telnet or serial port.
OBJECT-TYPE    
  SEQUENCE OF  
    NodeConsoleEntry

nodeConsoleEntry 1.3.6.1.4.1.277.1.3.57.1
Information of a console.
OBJECT-TYPE    
  NodeConsoleEntry  

nodeConsoleIndex 1.3.6.1.4.1.277.1.3.57.1.1
A positive integer to identify a console
OBJECT-TYPE    
  INTEGER 1..6  

nodeUserName 1.3.6.1.4.1.277.1.3.57.1.2
The login user name up to 31 characters. There is no validation of the name, i.e., any string is acceptable.
OBJECT-TYPE    
  OCTET STRING  

nodeUserFrom 1.3.6.1.4.1.277.1.3.57.1.3
The IP address from which the user logged in. 0.0.0.0 if the user logged in through serial port.
OBJECT-TYPE    
  IpAddress  

nodeConsoleAccessMode 1.3.6.1.4.1.277.1.3.57.1.4
The access mode of the console. By default, a user is in READ ONLY mode.
OBJECT-TYPE    
  INTEGER readOnly(1), readWrite(2)  

nodeConsoleUptime 1.3.6.1.4.1.277.1.3.57.1.5
How long the console has been active.
OBJECT-TYPE    
  TimeTicks  

nodePsADiagCode 1.3.6.1.4.1.277.1.3.58
The failure code of the power supply A. A non-zero value indicates one or more failures. Refer to the hardware manual for a description of the failure code.
OBJECT-TYPE    
  INTEGER  

nodePsBDiagCode 1.3.6.1.4.1.277.1.3.59
The failure code of the power supply B. A non-zero value indicates one or more failures. Refer to the hardware manual for a description of the failure code.
OBJECT-TYPE    
  INTEGER  

nodeFrameMemoryUtil 1.3.6.1.4.1.277.1.3.60
The percentage of frame memory utilization on this intelligent card.
OBJECT-TYPE    
  Gauge  

nodeFrameMemoryUsage 1.3.6.1.4.1.277.1.3.61
The frame memory utilization, in terms of free bytes, for this intelligent card.
OBJECT-TYPE    
  Gauge  

nodeCapability 1.3.6.1.4.1.277.1.3.62
The capability of this node.
OBJECT-TYPE    
  INTEGER frame-relay(1), smds(2)  

nodeSvcLastCallFailure 1.3.6.1.4.1.277.1.3.63
A textual string describing the last call failure.
OBJECT-TYPE    
  OCTET STRING  

nodeRerouteDelay 1.3.6.1.4.1.277.1.3.64
The number of seconds delay between each reroute batch event.
OBJECT-TYPE    
  INTEGER  

nodeRerouteCount 1.3.6.1.4.1.277.1.3.65
The number of virtual circuits to request a reroute for duing a single reroute batch event.
OBJECT-TYPE    
  INTEGER  

nodeFileTransferRequest 1.3.6.1.4.1.277.1.3.66
This object is used to initiate file transfers to and from the switch. A management station can initiate a file transfer by settting this object of text string in the following format: operation filename time-to-wait target-host protocol where operation - [get | put], filename - configuration.[card] time-to-wait - a number in seconds target-host - the IP address of target host protocol - [tftp | ftp] Multiple transfers can be specified by repeating above with ';' between each transfer specifier. Examples: o get configuration.10 5 152.148.10.100 tftp will start a transfer of configuration information on card 10 to host 152.148.10.100 in 5 seconds. o put configuration.1 2 152.148.1.1 tftp ; get configuration.1 15 152.148.1.1 tftp will (1) transfer configuration.1 from 152.148.1.1 (2) transfer configuration.2 to 152.148.1.1 To cancel the transfer request, set this object to empty.
OBJECT-TYPE    
  DisplayString  

nodeFileTransferStatus 1.3.6.1.4.1.277.1.3.67
The status of the file tarnsfer.
OBJECT-TYPE    
  INTEGER complete(1), active(2), failed(3), invalid(4), filename(5), timeout(6), canceled(7)  

nodeTime 1.3.6.1.4.1.277.1.3.68
The current wall-clock time that is set on the switch in Universal Coordinated Time (UCT). The value is the number of seconds since 00:00:00 UCT January 1, 1970.
OBJECT-TYPE    
  TimeTicks  

nodeBillingAPAddress 1.3.6.1.4.1.277.1.3.69
The IP Address of the Adjunct Billing Processor that is servicing this switch.
OBJECT-TYPE    
  IpAddress  

nodeBillingAPUsername 1.3.6.1.4.1.277.1.3.70
The Username of the account on the Adjunct Billing Processor to which usage data will be transferred via FTP.
OBJECT-TYPE    
  DisplayString  

nodeBillingAPPassword 1.3.6.1.4.1.277.1.3.71
The Password corresponding to the account identified by nodeBillingAPUsername. A NULL string is returned when read.
OBJECT-TYPE    
  DisplayString  

nodeBillingSwAPCommsFailures 1.3.6.1.4.1.277.1.3.72
The number of times that communication from the switch to the Adjunct Billing Processor has failed during the current aggregation period. A failure signifies failure of a file transfer operation to the Adjunct Processor.
OBJECT-TYPE    
  Counter  

nodeBillingTable 1.3.6.1.4.1.277.1.3.73
A table of Billing System managable objects, indexed by service.
OBJECT-TYPE    
  SEQUENCE OF  
    NodeBillingEntry

nodeBillingEntry 1.3.6.1.4.1.277.1.3.73.1
A nodeBillingEntry contains a set of statistics that summarize the Billing System performance for a particular service.
OBJECT-TYPE    
  NodeBillingEntry  

nodeBillingService 1.3.6.1.4.1.277.1.3.73.1.1
The service being reported. This is the index into the table. Additional table rows for Frame Relay and ATM may be provided in the future.
OBJECT-TYPE    
  INTEGER smds(1)  

nodeBilling 1.3.6.1.4.1.277.1.3.73.1.2
Switch to enable and disable billing on the STDX. When the value of nodeBilling is 'enabled', the value of a logical port's lportBilling object will take precedence. When the value of nodeBilling is 'disabled', it overrides all logical ports' lportBilling objects and billing is disabled across the entire switch. The default value of this object is 'disabled'.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

nodeBillingAggrPeriod 1.3.6.1.4.1.277.1.3.73.1.3
Defines the length of the Billing Aggregation Period in seconds. The default value is 15 minutes. The minimum value is 10 minutes.
OBJECT-TYPE    
  TimeTicks  

nodeBillingCurAggrPeriodStart 1.3.6.1.4.1.277.1.3.73.1.4
The start-time of the current aggregation period, given by the number of seconds since 00:00:00 UCT January 1, 1970.
OBJECT-TYPE    
  TimeTicks  

nodeBillingCurAggrPeriodEnd 1.3.6.1.4.1.277.1.3.73.1.5
The end-time of the current aggregation period, given by the number of seconds since 00:00:00 UCT January 1, 1970.
OBJECT-TYPE    
  TimeTicks  

nodeBillingCollection 1.3.6.1.4.1.277.1.3.73.1.6
Defines how often the Data Aggregation process on the CP is to poll the IOPs for usage data. The default value is 30 second. The range is unbounded, but practical use will dictate a range from 30 seconds to 1 minute.
OBJECT-TYPE    
  TimeTicks  

nodeBillingDailyProcessing 1.3.6.1.4.1.277.1.3.73.1.7
Defines whether the Billing System is to perform a set of carrier-specific actions at the time given by nodeBillingDPTime. This object can be used to schedule the generation of statistics on a 24-hour basis, for example.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

nodeBillingDPTime 1.3.6.1.4.1.277.1.3.73.1.8
Defines the time (given by the number of seconds since 00:00:00 UCT) that the Billing System is to perform a set of carrier-specific actions. This object can be used to schedule the generation of statistics on a 24-hour basis, for example.
OBJECT-TYPE    
  TimeTicks  

nodeBillingUsageRecOvflWarnings 1.3.6.1.4.1.277.1.3.73.1.9
Count of the number of usage record counter-value overflow conditions that have occurred during the current aggregation period. An overflow condition exists when an attempt was made to update a usage record counter, but such an update would have overflowed the counter. In this case, the usage record is closed and a new one is opened, if there is sufficient space in the service's aggregated usage data store.
OBJECT-TYPE    
  Counter  

nodeBillingTotalUsageRecOvflWarnings 1.3.6.1.4.1.277.1.3.73.1.10
Count of the number of usage record overflow conditions that have occurred during the current day.
OBJECT-TYPE    
  Counter  

nodeBillingBillableUsageEvents 1.3.6.1.4.1.277.1.3.73.1.11
Count of the number of data units (e.g, SMDS L3 PDUs) processed for billing treatment.
OBJECT-TYPE    
  Counter  

nodeBillingNonBillableUsageEvents 1.3.6.1.4.1.277.1.3.73.1.12
Count of the number of data units (e.g, SMDS L3 PDUs) not considered for billing treatment.
OBJECT-TYPE    
  Counter  

nodeBillingUsageRecCreated 1.3.6.1.4.1.277.1.3.73.1.13
Count of the number of usage records created during the current aggregation period.
OBJECT-TYPE    
  Counter  

nodeBillingTotalUsageRecCreated 1.3.6.1.4.1.277.1.3.73.1.14
Count of the total number of usage records created during the current day.
OBJECT-TYPE    
  Counter  

nodeBillingUsageRecCrFailures 1.3.6.1.4.1.277.1.3.73.1.15
Total number of usage records that could not be created during the current aggregation period. This counter is normally incremented when the usage data file is at capacity and no additional usage records can be added.
OBJECT-TYPE    
  Counter  

nodeBillingTotalUsageRecCrFailures 1.3.6.1.4.1.277.1.3.73.1.16
Total number of usage records that could not be created during the current day.
OBJECT-TYPE    
  Counter  

nodeBillingUsageRecSent 1.3.6.1.4.1.277.1.3.73.1.17
Total number of usage records that have been transferred to the Adjunct Billing Processor during the current aggregation period.
OBJECT-TYPE    
  Counter  

nodeBillingTotalUsageRecSent 1.3.6.1.4.1.277.1.3.73.1.18
Total number of usage records that have been transferred to the Adjunct Billing Processor during the current day.
OBJECT-TYPE    
  Counter  

nodeBillingUsageDataStoreFull 1.3.6.1.4.1.277.1.3.73.1.19
The number of times the aggregated usage data store became full during the current aggregation period.
OBJECT-TYPE    
  Counter  

nodeBillingTotalUsageDataStoreFull 1.3.6.1.4.1.277.1.3.73.1.20
Total number of times the aggregated usage data store became full during the current day.
OBJECT-TYPE    
  Counter  

nodeBillingAdminAction 1.3.6.1.4.1.277.1.3.73.1.21
This object defines a set of administrative actions that can be performed by the Billing System. forceUpload - Forces the current aggregation period to end and the service's aggregated usage data file to be uploaded to the Adjunct Processor. A new aggregation period is then started. This action can be requested when billing is enabled or disabled for the service. This object always returns invalid(1) when read.
OBJECT-TYPE    
  INTEGER invalid(1), forceUpload(2)  

nodeRerouteAlg 1.3.6.1.4.1.277.1.3.74
The number of seconds delay between each reroute batch event.
OBJECT-TYPE    
  INTEGER negneg(1), pospos(2), disable(3)  

nodeOamAlarmDisabled 1.3.6.1.4.1.277.1.3.76
If disabled then don't generate oam alarms for circuits that are down on this switch.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

nodeRefclocksrcTable 1.3.6.1.4.1.277.1.3.77
A list of generators (sources) for the system reference clock on the node. This reference clock is used by the clock generation unit (CGU) to create the system clock. To this reference clock the constant bit rate ATM interface cards (CBR cards) are synchronized.
OBJECT-TYPE    
  SEQUENCE OF  
    NodeRefclocksrcEntry

nodeRefclocksrcEntry 1.3.6.1.4.1.277.1.3.77.1
Information of a single system reference clock source.
OBJECT-TYPE    
  NodeRefclocksrcEntry  

nodeRefclocksrcIndex 1.3.6.1.4.1.277.1.3.77.1.1
A positive integer to identify an entry in the nodeRefclocksrcTable.
OBJECT-TYPE    
  INTEGER 1..20  

nodeRefclocksrcPriority 1.3.6.1.4.1.277.1.3.77.1.2
The priority of the system reference clock source. A source with a nodeRefclocksrcPriority=n means that this source is used before a source with a higher value of nodeRefclocksrcPriority as long as this source is available. The system choses one of the sources with the same lowest available value of nodeRefclocksrcPriority.
OBJECT-TYPE    
  INTEGER 1..20  

nodeRefclocksrcType 1.3.6.1.4.1.277.1.3.77.1.3
The type of the reference clock source. It is either an external clock source connected to a ATM-IWU or DS3 card, or the reference clock is recovered from the line interface.
OBJECT-TYPE    
  INTEGER external(1), pport(2)  

nodeRefclocksrcSlotId 1.3.6.1.4.1.277.1.3.77.1.4
The card number of the reference clock source. In case of an external clock interface this is the number of the card as defined in cardLogicalSlotId. In case of a clock recovered from the line interface it is the number of the corresponding card as defined in cardLogicalSlotId.
OBJECT-TYPE    
  INTEGER  

nodeRefclocksrcPportId 1.3.6.1.4.1.277.1.3.77.1.5
The interface number of the reference clock source. In case of an external clock interface this is meaningless. In case of a clock recovered from the line interface it is the number of the corresponding pport as defined in pportId.
OBJECT-TYPE    
  INTEGER  

nodeRefclockActiveSrc 1.3.6.1.4.1.277.1.3.78
The entry number of the active reference clock source in nodeRefclocksrcTable. If zero, the CGU is in free-running mode or holdover mode using the last PLL parameters.
OBJECT-TYPE    
  INTEGER  

nodeRefclockActiveCGUSlotId 1.3.6.1.4.1.277.1.3.79
The physical slot id of the current master CGU board.
OBJECT-TYPE    
  INTEGER  

nodeRefclockActiveCGUMode 1.3.6.1.4.1.277.1.3.80
The clock mode of the current master CGU board.
OBJECT-TYPE    
  INTEGER free-running(1), sync-to-reference-clock(2), holdover(3), extended-holdover(4)  

nodeInitiateImageBackup 1.3.6.1.4.1.277.1.3.81
When set, copy all of the runtime application images and configuration images to there corresponding backup locations on the hard disk.
OBJECT-TYPE    
  INTEGER proceed(1)  

nodeImageBackupState 1.3.6.1.4.1.277.1.3.82
Provides the current state of the images backup operation.
OBJECT-TYPE    
  INTEGER proceeding(1), done(2)  

nodeInitiateImageRestore 1.3.6.1.4.1.277.1.3.83
When set, copy all of the runtime application images and configuration images from their BACKUP locations on the hard disk to there corresponding ACTIVE locations on the hard disk. Once completed, reboot the entire node.
OBJECT-TYPE    
  INTEGER proceed(1)  

nodeApplicationTable 1.3.6.1.4.1.277.1.3.84
A list of Application Image Descriptions.
OBJECT-TYPE    
  SEQUENCE OF  
    NodeApplicationEntry

nodeApplicationEntry 1.3.6.1.4.1.277.1.3.84.1
An Application Entry contains a description of the application image, the version of the PRIMARY copy and the version of the SECONDARY copy.
OBJECT-TYPE    
  NodeApplicationEntry  

nodeApplicationIndex 1.3.6.1.4.1.277.1.3.84.1.1
The numeric index of application images. 1 - SP Runtime Application 2 - IOM Type A Runtime Application 3 - IOM Type B Runtime Application 4 - IOM Type C Runtime Application 5 - IOM Type D Runtime Application
OBJECT-TYPE    
  Index  

nodeApplicationDescription 1.3.6.1.4.1.277.1.3.84.1.2
The description of this Application Image.
OBJECT-TYPE    
  DisplayString  

nodePrimaryVersion 1.3.6.1.4.1.277.1.3.84.1.3
The version of the PRIMARY Application Image.
OBJECT-TYPE    
  DisplayString  

nodeSecondaryVersion 1.3.6.1.4.1.277.1.3.84.1.4
The version of the SECONDARY Application Image.
OBJECT-TYPE    
  DisplayString  

nodePrimarySyncRefAdminState 1.3.6.1.4.1.277.1.3.85
The requested primary clock synchronization reference source.
OBJECT-TYPE    
  INTEGER externala(1), externalb(2), portrefa(3), portrefb(4), internal(5)  

nodePrimarySyncRefOperationalState 1.3.6.1.4.1.277.1.3.86
The actual primary clock synchronization reference source.
OBJECT-TYPE    
  INTEGER externala(1), externalb(2), portrefa(3), portrefb(4), internal(5)  

nodeSecondarySyncRefAdminState 1.3.6.1.4.1.277.1.3.87
The requested secondary clock synchronization reference source.
OBJECT-TYPE    
  INTEGER externala(1), externalb(2), portrefa(3), portrefb(4), internal(5)  

nodeSecondarySyncRefOperationalState 1.3.6.1.4.1.277.1.3.88
The actual secondary clock synchronization reference source.
OBJECT-TYPE    
  INTEGER externala(1), externalb(2), portrefa(3), portrefb(4), internal(5)  

nodePrimaryPLLOperationalState 1.3.6.1.4.1.277.1.3.89
The current state of the primary synchronization PLL.
OBJECT-TYPE    
  INTEGER active(1), down(2)  

nodeSecondaryPLLOperationalState 1.3.6.1.4.1.277.1.3.90
The current state of the secondary synchronization PLL.
OBJECT-TYPE    
  INTEGER active(1), down(2)  

nodeExternalClockAOperationalState 1.3.6.1.4.1.277.1.3.91
The current state of the External Clock A reference.
OBJECT-TYPE    
  INTEGER active(1), ais(2), los(3)  

nodeExternalClockBOperationalState 1.3.6.1.4.1.277.1.3.92
The current state of the External Clock B reference.
OBJECT-TYPE    
  INTEGER active(1), ais(2), los(3)  

nodePortClockAOperationalState 1.3.6.1.4.1.277.1.3.93
The current state of the Port Clock A reference.
OBJECT-TYPE    
  INTEGER active(1), down(2)  

nodePortClockBOperationalState 1.3.6.1.4.1.277.1.3.94
The current state of the Port Clock B reference.
OBJECT-TYPE    
  INTEGER active(1), down(2)  

nodeExternalTimingSource 1.3.6.1.4.1.277.1.3.95
The reference for the external timing output.
OBJECT-TYPE    
  INTEGER externala(1), externalb(2), portrefa(3), portrefb(4), internal(5)  

nodeSyncAutoRestore 1.3.6.1.4.1.277.1.3.96
The configuration of the Synchronization Reference Auto Restoration function.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

nodeExternalClockInterfaceType 1.3.6.1.4.1.277.1.3.97
The interface type of the External Clock references.
OBJECT-TYPE    
  INTEGER t1(1), e1bnc(2), e1ww(3)  

pport 1.3.6.1.4.1.277.1.4
OBJECT IDENTIFIER    

nodePsAStatusChange 1.3.6.1.4.1.277.1.4
This trap indicates that the power supply A has changed state (toggled between up and down states).
TRAP-TYPE    
  nodePsAStatus  

pportNumber 1.3.6.1.4.1.277.1.4.1
The number of physical ports (regardless of their current state) present at this node.
OBJECT-TYPE    
  INTEGER  

pportTable 1.3.6.1.4.1.277.1.4.2
A list of physical port entries. The number of entries is given by the value of pportNumber.
OBJECT-TYPE    
  SEQUENCE OF  
    PportEntry

pportEntry 1.3.6.1.4.1.277.1.4.2.1
The physical port entry contains objects relevant to a physical port.
OBJECT-TYPE    
  PportEntry  

pportSlotId 1.3.6.1.4.1.277.1.4.2.1.1
The slot number of the corresponding physical port.
OBJECT-TYPE    
  INTEGER  

pportId 1.3.6.1.4.1.277.1.4.2.1.2
The port number of the corresponding physical port on the board.
OBJECT-TYPE    
  INTEGER  

pportAdminType 1.3.6.1.4.1.277.1.4.2.1.3
The defined type of the board which the physical port is on.
OBJECT-TYPE    
  INTEGER v35-6(1), ft1-1-24(2), fe1-1-30(3), uio-6(4), cp1(5), uio-8(6), ft1-4-24(7), fe1-4-30(8), ft3-1(9), fe3-1(10), hssi-1(11), dsx1-10(12), rs232-18(13), rs232-8(14), ut1-4-24(15), ue1-4-30(16), atmds3-1(17), atme3-1(18), pri-4(19), e1-pri-4(20), sft1-4-24(21), sut1-4-24(22), st1-pri-4(23), t1-atm(24), e1-atm(25), ads3-t3(26), ads3-e3(27), cbr-ds1-s-4(28), cbr-ds1-us-4(29), cbr-e1-s-4(30), cbr-e1-us-4(31), cbr-atmiwu-1(32), toc3-atm-4(33), tstm1-atm-4(34), atmcs-1(35)  

pportNumLport 1.3.6.1.4.1.277.1.4.2.1.4
The number of logical ports on the physical port.
OBJECT-TYPE    
  INTEGER  

pportDataRate 1.3.6.1.4.1.277.1.4.2.1.5
An estimate of the physical port's data rate in bits per second. The data rate can't be an arbitrary value. The legal values are list below. Note that the T1/E1 class of cards don't support this variable and return a 0 For UIO, DSX1: 9600, 19200, 38400, 48000, 56000, 64000, 128000, 192000, 256000, 320000, 384000, 448000, 512000, 576000, 640000, 704000, 768000, 832000, 896000, 960000, 1024000, 1088000, 1152000, 1216000, 1280000, 1344000, 1408000, 1472000, 1536000, 1600000, 1664000, 1728000, 1792000, 1856000, 1920000, 1984000, 2048000, 4096000, 6144000, 8192000 For HSSI: 1579000, 3158000, 4737000, 6316000, 7895000, 9474000, 11053000, 12632000, 14211000, 15790000, 17369000, 18948000, 20527000, 22106000, 23685000, 25264000, 26843000, 28422000, 30001000, 31580000, 33159000, 34738000, 36317000, 37896000, 39475000, 41054000, 42633000, 44212000, 45791000, 47370000, 48949000, 50528000 For ATM-IWU, TOPAZ OC3c: 155520000 For T1, E1, UT1, UE1, PRI, SH-T1: 0
OBJECT-TYPE    
  INTEGER  

pportType 1.3.6.1.4.1.277.1.4.2.1.6
The actual type of the physical port.
OBJECT-TYPE    
  INTEGER v35-6(1), ft1-1-24(2), fe1-1-30(3), uio-6(4), cp1(5), uio-8(6), ft1-4-24(7), fe1-4-30(8), ft3-1(9), fe3-1(10), hssi-1(11), dsx1-10(12), rs232-18(13), rs232-8(14), ut1-4-24(15), ue1-4-30(16), atm-1(17), atme3-1(18), pri-4(19), e1-pri-4(20), sft1-4-24(21), sut1-4-24(22), st1-pri-4(23), t1-atm(24), e1-atm(25), ads3-t3(26), ads3-e3(27), cbr-ds1-s-4(28), cbr-ds1-us-4(29), cbr-e1-s-4(30), cbr-e1-us-4(31), cbr-atmiwu-1(32), toc3-atm-4(33), tstm1-atm-4(34), atmcs-1(35)  

pportRecvClock 1.3.6.1.4.1.277.1.4.2.1.7
The receive clock source. This object works in cooperation with pportXmitClock. The following are the various values for different clock source types: Type Clock Source pportRevClock pportXmitClock { pportEntry 7 } { pportEntry 8 } V.35 DCE ............ 0 0 or UIO LoopTime DCE ... 3 0 DTE ............ 1 2 Direct Trunk ... 1 0 T1 or Loop Timed ..... 1 1 E1 Internal ....... 2 2 External ....... don't care 3
OBJECT-TYPE    
  INTEGER  

pportXmitClock 1.3.6.1.4.1.277.1.4.2.1.8
The transmit clock source. This object works in cooperation with pportXmitClock. The following are the various values for different clock source types: Type Clock Source pportRevClock pportXmitClock { pportEntry 7 } { pportEntry 8 } V.35 DCE ............ 0 0 or UIO LoopTime DCE ... 3 0 DTE ............ 1 2 Direct Trunk ... 1 0 T1 or Loop Timed ..... 1 1 E1 Internal ....... 2 2 External ....... don't care 3
OBJECT-TYPE    
  INTEGER  

pportAdminStatus 1.3.6.1.4.1.277.1.4.2.1.9
The desired state of the physical port.
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3)  

pportOperStatus 1.3.6.1.4.1.277.1.4.2.1.10
The current state of the physical port.
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3)  

pportDs1LineType 1.3.6.1.4.1.277.1.4.2.1.11
The line type of the T1 or FT1-24B port. ANSI ESF is equivalent to Bellcore ESF.
OBJECT-TYPE    
  INTEGER d4(1), esf-ansi(2), esf-att-address-a(3), esf-none(4), e1-cas-crc4(5), e1-cas-no-crc4(6), e1-no-cas-crc4(7), e1-no-cas-no-crc4(8), esf-att-address-b(9)  

pportDs1ZeroCoding 1.3.6.1.4.1.277.1.4.2.1.12
The variety of zero code suppression used on the T1 or FT1-24B link. Jammed bit is equivalent to dsx1JBZS where the DS0s will run at 56K bps.
OBJECT-TYPE    
  INTEGER ami(1), b8zs(2), hdb3(3), jammed-bit(4)  

pportDs1LineBuildout 1.3.6.1.4.1.277.1.4.2.1.13
The line build out or line length specification for the DS1 or DSX-1 transmitter. These values are card specific: 10 port DSX-1 card ------------------ The accepted values are: 1 - 0 to 110 feet 2 - 110 to 220 feet 3 - 220 to 330 feet 4 - 330 to 440 feet 5 - 440 to 550 feet 6 - 550 to 660 feet 7 - over 655 feet 1-port and 4-port T1 cards -------------------------- The accepted values are: 96 - 0 to 133 feet 128 - 133 to 266 feet 160 - 266 to 399 feet 192 - 399 to 533 feet 224 - 533 to 655 feet 96 - 0 db 32 - -7.5 db 64 - -15 db 4-port CBR card --------------- The accepted values are: 96 - 0 db 32 - -7.5 db 64 - -15 db 4-port Short Haul T1 cards -------------------------- The accepted values are: 96 - 0 to 133 feet 128 - 133 to 266 feet 160 - 266 to 399 feet 192 - 399 to 533 feet 224 - 533 to 655 feet
OBJECT-TYPE    
  INTEGER  

pportDiagTestId 1.3.6.1.4.1.277.1.4.2.1.14
Identification for the diagnostics tests to be run.
OBJECT-TYPE    
  INTEGER v35-sca-local-loopback(1), v35-sca-remote-loopback(2), v35-csu-loopback(3), hssi-local-dte-loopback(5), hssi-local-line(6), hssi-remote-line-loopback(7), ds1-framer-local-loopback(11), ds1-line-local-loopback(12), ds1-framer-remote-loopback(13), ds1-line-remote-loopback(14)  

pportDiagTestRuns 1.3.6.1.4.1.277.1.4.2.1.15
The number of passes of the diagnostics tests to be run. The default value is 1.
OBJECT-TYPE    
  INTEGER  

pportInOctets 1.3.6.1.4.1.277.1.4.2.1.16
The total number of octets received on the physical port, including framing characters.
OBJECT-TYPE    
  Counter  

pportInFrames 1.3.6.1.4.1.277.1.4.2.1.17
The total number of frames received on the physical port.
OBJECT-TYPE    
  Counter  

pportInDiscards 1.3.6.1.4.1.277.1.4.2.1.18
The total number of inbound frames discarded.
OBJECT-TYPE    
  Counter  

pportInErrors 1.3.6.1.4.1.277.1.4.2.1.19
The total number of inbound frames that contained erroneous headers (e.g., illegal or unknown DLCIs).
OBJECT-TYPE    
  Counter  

pportOutOctets 1.3.6.1.4.1.277.1.4.2.1.20
The total number of octets transmitted out of the physical port, including framing characters.
OBJECT-TYPE    
  Counter  

pportOutFrames 1.3.6.1.4.1.277.1.4.2.1.21
The total number of frames transmitted out of the physical port.
OBJECT-TYPE    
  Counter  

pportOutDiscards 1.3.6.1.4.1.277.1.4.2.1.22
The total number of outbound frames discarded due to severe congestion.
OBJECT-TYPE    
  Counter  

pportOutErrors 1.3.6.1.4.1.277.1.4.2.1.23
The total number of outbound frames that causes xmit errors.
OBJECT-TYPE    
  Counter  

pportDiagState 1.3.6.1.4.1.277.1.4.2.1.24
The current state of the diagnostic on this physical port.
OBJECT-TYPE    
  INTEGER active(1)  

pportDiagOptionStr 1.3.6.1.4.1.277.1.4.2.1.25
Optional parameters to the diagnostic.
OBJECT-TYPE    
  OCTET STRING  

pportDiagPassCount 1.3.6.1.4.1.277.1.4.2.1.26
Number of successful diagnostic passes.
OBJECT-TYPE    
  INTEGER  

pportDiagFailCount 1.3.6.1.4.1.277.1.4.2.1.27
Number of failed diagnostic passes.
OBJECT-TYPE    
  INTEGER  

pportDiagResultStr 1.3.6.1.4.1.277.1.4.2.1.28
Description of last diagnostic failure.
OBJECT-TYPE    
  DisplayString  

pportLinkDownReason 1.3.6.1.4.1.277.1.4.2.1.29
Reason why the link is down. The blue-alarm is equivalent to the Alarm Indication Signal (AIS) failure.
OBJECT-TYPE    
  INTEGER red-alarm(1), yellow-alarm(2), blue-alarm(4), carrier-loss(8), looped-back(16), ber-threshold(64), signal-label-mismatch(128), loss-of-signal(256), loss-of-frame(512), loss-of-cell-delination(1024), line-AIS(2048), path-AIS(4096), loss-of-pointer(8192), line-RFI(16384), path-RFI(32768), signal-label-undefined(65536)  

pportInterface 1.3.6.1.4.1.277.1.4.2.1.30
Actual interface connected to Multi-Interface Port or ATM-IWU.
OBJECT-TYPE    
  INTEGER eia449(1), x21(2), eia530(3), eia530A(4), v35(5), e1-coax(6), e1-db(7), none(8), v24(9), sonet(10), sdh(11), multi-mode(12), single-mode(13)  

pportAdminInterface 1.3.6.1.4.1.277.1.4.2.1.31
Configured interface connected to Multi-Interface Port or ATM-IWU.
OBJECT-TYPE    
  INTEGER eia449(1), x21(2), eia530(3), eia530A(4), v35(5), e1-coax(6), e1-db(7), none(8), v24(9), sonet(10), sdh(11), multi-mode(12), single-mode(13)  

pportCellScramble 1.3.6.1.4.1.277.1.4.2.1.32
Configured ATM cell payload scrambling.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

pportCbitParity 1.3.6.1.4.1.277.1.4.2.1.33
Configured ATM DS3 C-bit Parity.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

pportMaxBufferSize 1.3.6.1.4.1.277.1.4.2.1.34
Maximum receive/transmit buffer size for the ATM UNI DS3 IOP
OBJECT-TYPE    
  INTEGER  

pportPeakCellRate0 1.3.6.1.4.1.277.1.4.2.1.35
Peak Cell Rate (cell/sec.) for rate queue #0. rate queues 0 - 3 are high priority
OBJECT-TYPE    
  INTEGER  

pportPeakCellRate1 1.3.6.1.4.1.277.1.4.2.1.36
Peak Cell Rate (cell/sec.) for rate queue #1. rate queues 0 - 3 are high priority
OBJECT-TYPE    
  INTEGER  

pportPeakCellRate2 1.3.6.1.4.1.277.1.4.2.1.37
Peak Cell Rate (cell/sec.) for rate queue #2. rate queues 0 - 3 are high priority
OBJECT-TYPE    
  INTEGER  

pportPeakCellRate3 1.3.6.1.4.1.277.1.4.2.1.38
Peak Cell Rate (cell/sec.) for rate queue #3. rate queues 0 - 3 are high priority
OBJECT-TYPE    
  INTEGER  

pportPeakCellRate4 1.3.6.1.4.1.277.1.4.2.1.39
Peak Cell Rate (cell/sec.) for rate queue #4. rate queues 4 - 7 are low priority
OBJECT-TYPE    
  INTEGER  

pportPeakCellRate5 1.3.6.1.4.1.277.1.4.2.1.40
Peak Cell Rate (cell/sec.) for rate queue #5. rate queues 4 - 7 are low priority
OBJECT-TYPE    
  INTEGER  

pportPeakCellRate6 1.3.6.1.4.1.277.1.4.2.1.41
Peak Cell Rate (cell/sec.) for rate queue #6. rate queues 4 - 7 are low priority
OBJECT-TYPE    
  INTEGER  

pportPeakCellRate7 1.3.6.1.4.1.277.1.4.2.1.42
Peak Cell Rate (cell/sec.) for rate queue #7. rate queues 4 - 7 are low priority
OBJECT-TYPE    
  INTEGER  

pportInCells 1.3.6.1.4.1.277.1.4.2.1.43
The total number of cells received
OBJECT-TYPE    
  INTEGER  

pportInErrorCells 1.3.6.1.4.1.277.1.4.2.1.44
The total number of cells received with error
OBJECT-TYPE    
  INTEGER  

pportOutCells 1.3.6.1.4.1.277.1.4.2.1.45
The total number of cells transmitted
OBJECT-TYPE    
  INTEGER  

pportDs3LineBuildout 1.3.6.1.4.1.277.1.4.2.1.46
The line build out or line length specification for the DS3 transmitter. 1-port ATM-UNI DS3 card -------------------------- The accepted values are: 1 - 0 to 225 feet 2 - 226 to 450 feet
OBJECT-TYPE    
  INTEGER  

pportSetDS0LoopUp 1.3.6.1.4.1.277.1.4.2.1.47
Bit map used to set one or more DS0's into loopback. Low bit corresponds to DS0 1. If a bit is set that DS0 is put into loopback.
OBJECT-TYPE    
  INTEGER  

pportSetDS0LoopDown 1.3.6.1.4.1.277.1.4.2.1.48
Bit map used to set one or more DS0's out of loopback. Low bit corresponds to DS0 1. If a bit is set that DS0 is put out of loopback.
OBJECT-TYPE    
  INTEGER  

pportDS0LoopUpStatus 1.3.6.1.4.1.277.1.4.2.1.49
Bit map reporting which DS0's have gone into loopback since the last time this variable was read
OBJECT-TYPE    
  INTEGER  

pportDS0LoopDownStatus 1.3.6.1.4.1.277.1.4.2.1.50
Bit map reporting which DS0's have gone out of loopback since the last time this variable was read
OBJECT-TYPE    
  INTEGER  

pportDS0LoopStatus 1.3.6.1.4.1.277.1.4.2.1.51
Bit map reporting which DS0's are currently in loopback. Low bit corresponds to DS0 1
OBJECT-TYPE    
  INTEGER  

pportISDN 1.3.6.1.4.1.277.1.4.2.1.52
Specifies whether ISDN PRI is enabled for this physical port
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

pportdsx3LoopbackConfig 1.3.6.1.4.1.277.1.4.2.1.53
Integer used to set the loopback state of the DS3 or E3
OBJECT-TYPE    
  INTEGER dsx3NoLoop(1), dsx3PayloadLoop(2), dsx3LineLoop(3)  

pportdsx3SendCode 1.3.6.1.4.1.277.1.4.2.1.54
Integer used to send loopback code to far-end DS3
OBJECT-TYPE    
  INTEGER dsx3SendNoCode(1), dsx3SendLineCode(2), dsx3SendResetCode(4)  

pportdsx3LoopStatus 1.3.6.1.4.1.277.1.4.2.1.55
Integer indicating the current loopback status of the DS3 or E3
OBJECT-TYPE    
  INTEGER noloop(1), payloadloop(2), lineloop(3)  

pportdsx3FEACStatus 1.3.6.1.4.1.277.1.4.2.1.56
Integer indicating the current DS3 FAEC status: -- none (0), DS3 Equipment Failure (1), DS3 LOS (2), DS3 Out of Frame (4), DS3 AIS received (8), DS3 IDLE received (16), DS3 Equipment-Failure (NSA) (32), DS3 Common Equipment Failure (64), DS3 Loopback received (128)
OBJECT-TYPE    
  INTEGER  

pportds1LoopbackConfig 1.3.6.1.4.1.277.1.4.2.1.57
Integer used to set the loopback state of the DS1
OBJECT-TYPE    
  INTEGER ds1NoLoop(1), ds1PayloadLoop(2), ds1LineLoop(3)  

pportds1SendCode 1.3.6.1.4.1.277.1.4.2.1.58
Integer used to send loopback code to far-end DS1
OBJECT-TYPE    
  INTEGER ds1SendNoCode(1), ds1SendFramedInbandLineActuateLoop(2), ds1SendFramedInbandLineReleaseLoop(3), ds1SendUnframedInbandLineActuateLoop(4), ds1SendUnframedInbandLineReleaseLoop(5), ds1SendFdlESFAnsiLineActuateLoop(6), ds1SendFdlESFAnsiLineReleaseLoop(7), ds1SendFdlESFAnsiPayloadActuateLoop(8), ds1SendFdlESFAnsiPayloadReleaseLoop(9)  

pportds1LoopStatus 1.3.6.1.4.1.277.1.4.2.1.59
Integer indicating the current loopback status of the DS1
OBJECT-TYPE    
  INTEGER noloop(1), payloadloop(2), lineloop(3)  

pportSetClkBkup 1.3.6.1.4.1.277.1.4.2.1.60
The desired clock source backup if the card is set in external clock source mode
OBJECT-TYPE    
  INTEGER internalClkBkup(1), looptimedClkBkup(2)  

pportAtmIdleWord 1.3.6.1.4.1.277.1.4.2.1.61
The word used to stuff the payload of the ATM idle cell
OBJECT-TYPE    
  INTEGER  

pportAtmDisCardMode 1.3.6.1.4.1.277.1.4.2.1.62
The desired clock source backup if the card is set in external clock source mode
OBJECT-TYPE    
  INTEGER ansiInval(1), ansiUnassignedInval(2), atmFInvalid(3), atmFUnassignedInval(4), ccittIdle(5), ccittUnassignedIdle(6)  

pportAtmLastUnconfiguredVpi 1.3.6.1.4.1.277.1.4.2.1.63
This entry holds the Vpi read from the last Unconfigured atm cell received. This entry applies to ATM pports only.
OBJECT-TYPE    
  INTEGER  

pportAtmLastUnconfiguredVci 1.3.6.1.4.1.277.1.4.2.1.64
This entry holds the Vci read from the last Unconfigured atm cell received. This entry applies to ATM pports only.
OBJECT-TYPE    
  INTEGER  

pportAtmUnconfiguredCells 1.3.6.1.4.1.277.1.4.2.1.65
This entry holds a count of the number of Unconfigured ATM cells received. This entry applies to ATM pports only.
OBJECT-TYPE    
  Counter  

pportAtmNumBitsVCI 1.3.6.1.4.1.277.1.4.2.1.66
This entry holds a count of the VCI bits supppoted my this ATM card.
OBJECT-TYPE    
  INTEGER  

pportAtmNumBitsVPI 1.3.6.1.4.1.277.1.4.2.1.67
This entry holds a count of the VPI bits supppoted my this ATM card.
OBJECT-TYPE    
  INTEGER  

pportAtmInterfaceType 1.3.6.1.4.1.277.1.4.2.1.68
Integer used to set ATM UNI or NNI type
OBJECT-TYPE    
  INTEGER uni(1), nni(2)  

pportSonetSDHLoopbackConfig 1.3.6.1.4.1.277.1.4.2.1.69
Integer used to set the loopback state of the Sonet/SDH port
OBJECT-TYPE    
  INTEGER noLoop(1), lineLoop(2), diagnosticsLoop(3)  

pportSonetSDHLoopStatus 1.3.6.1.4.1.277.1.4.2.1.70
Integer indicating the current loopback status of the Sonet/SDH port
OBJECT-TYPE    
  INTEGER noLoop(1), lineLoop(2), diagnosticsLoop(3)  

pportOutDiscardsCell 1.3.6.1.4.1.277.1.4.2.1.71
The total number of outbound cell discarded due to congestion.
OBJECT-TYPE    
  Counter  

pportAtmPlcp 1.3.6.1.4.1.277.1.4.2.1.72
The PLCP maintains the state of the ATM Physical Layer Convergence Protocol. When the protocol is disabled atm direct mapping is used with hec cell delineation.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

pportCbrTargetClockMode 1.3.6.1.4.1.277.1.4.2.1.73
The clocking method to be used by the CBR card. 4-port CBR card ----------------------------------------------- 1 - synchronous (external) clocking 2 - SRTS clocking 3 - adaptive clock method
OBJECT-TYPE    
  INTEGER  

pportCbrCurrentClockMode 1.3.6.1.4.1.277.1.4.2.1.74
The clocking method currently used by the CBR card. 4-port CBR card ----------------------------------------------- 1 - synchronous (external) clocking 2 - SRTS clocking 3 - adaptive clock method
OBJECT-TYPE    
  INTEGER  

pportClockMasterChannel 1.3.6.1.4.1.277.1.4.2.1.75
The number of the channel (lport) on this pport that is used as ACM/SRTS master for this line interface: 4-port CBR E1/DS1 card (structured mode): 1..4
OBJECT-TYPE    
  INTEGER  

pportFibreType 1.3.6.1.4.1.277.1.4.2.1.76
The type of fibre connected to the ATM-IWU. Its type determines the maximum transmission distance. 1-port ATM-IWU STM-1/STS-3c card -------------------------------- 4 - multimode fibre (maximum transmission distance approx. 2 km) 2 - single mode fibre short haul (maximum transmission distance approx. 20 km)
OBJECT-TYPE    
  INTEGER sonetMultiMode(4), sonetShortSingleMode(2)  

pportLaserStatus 1.3.6.1.4.1.277.1.4.2.1.77
The configured state of the laser: 1-port ATM-IWU STM-1/STS-3c card & Topaz 4-port OC3 & STM-1 card ---------------------------------------------------------------- 1 - off 2 - on
OBJECT-TYPE    
  INTEGER off(1), on(2)  

pportMaxActiveVpiBits 1.3.6.1.4.1.277.1.4.2.1.78
The maximum number of active VPI bits configured for use at the ATM interface. At the ATM UNI, the maximum number of active VPI bits configured for use ranges from 0 to 8 only.
OBJECT-TYPE    
  INTEGER 0..12  

pportBipErrorsThresh 1.3.6.1.4.1.277.1.4.2.1.79
The threshold of BIP errors. If the number of line BIP-24/8 rrors persists to exceed this value, the pport will be taken down and a trap will be issued: 1-port ATM-IWU STM-1/STS-3c card: -------------------------------- 1 - ignore BIP errors 4 - 10^-4 errors 5 - 10^-5 errors 6 - 10^-6 errors
OBJECT-TYPE    
  INTEGER  

pportBipSectionErrors 1.3.6.1.4.1.277.1.4.2.1.80
The number of B1 section BIP-8 errors since the last reset.
OBJECT-TYPE    
  Counter  

pportBipLineErrors 1.3.6.1.4.1.277.1.4.2.1.81
The number of line BIP-24/8 errors since the last reset.
OBJECT-TYPE    
  Counter  

pportBipPathErrors 1.3.6.1.4.1.277.1.4.2.1.82
The number of B3 path BIP-8 errors since the last reset.
OBJECT-TYPE    
  Counter  

pportFebeErrors 1.3.6.1.4.1.277.1.4.2.1.83
The number of line Far End Block Errors since the last reset.
OBJECT-TYPE    
  Counter  

pportHcsErrors 1.3.6.1.4.1.277.1.4.2.1.84
The number of correctable HCS errors since the last reset.
OBJECT-TYPE    
  Counter  

pportHcsSevereErrors 1.3.6.1.4.1.277.1.4.2.1.85
The number of uncorrectable HCS errors since the last reset.
OBJECT-TYPE    
  Counter  

pportCongestedReceivedCells 1.3.6.1.4.1.277.1.4.2.1.86
The number of received cells that were discarded due to congestion of the ATM-IWU, since the last reset.
OBJECT-TYPE    
  Counter  

pportCongestedTransmittedCells 1.3.6.1.4.1.277.1.4.2.1.87
The number of cells to be transmitted, that were discarded due to congestion of the ATM-IWU, since the last reset.
OBJECT-TYPE    
  Counter  

pportAtmLayerErroredReceivedCells 1.3.6.1.4.1.277.1.4.2.1.88
The number of received cells that were discarded due to ATM layer errors, since the last reset.
OBJECT-TYPE    
  Counter  

pportAtmLayerErroredTransmittedCells 1.3.6.1.4.1.277.1.4.2.1.89
The number of cells to be transmitted, that were discarded due to ATM layer errors, since the last reset.
OBJECT-TYPE    
  Counter  

pportDS0BitStuff 1.3.6.1.4.1.277.1.4.2.1.90
Bit stuffing on or off for 2047 bit pattern in DS0 far end testing.
OBJECT-TYPE    
  INTEGER  

pportDS0BitErrorCount 1.3.6.1.4.1.277.1.4.2.1.91
Total number of errors in 2047 DS0 far end testing.
OBJECT-TYPE    
  INTEGER  

pportDS0BitErrorFreeSeconds 1.3.6.1.4.1.277.1.4.2.1.92
Total number of error free seconds in 2047 DS0 far end testing.
OBJECT-TYPE    
  INTEGER  

pportDS0BitErroredSeconds 1.3.6.1.4.1.277.1.4.2.1.93
Total number of errored seconds in 2047 DS0 far end testing.
OBJECT-TYPE    
  INTEGER  

pportDS0MidspanRepeaters 1.3.6.1.4.1.277.1.4.2.1.94
Number of Midspan repeaters in a link to be punched thru for DS0 far end testing.
OBJECT-TYPE    
  INTEGER  

pportDS0TestPatternSync 1.3.6.1.4.1.277.1.4.2.1.95
While DS0 far end testing, the DS0 pattern has detected the pattern four consecutive times. If the pattern is lost, this variable will be equal to one.
OBJECT-TYPE    
  INTEGER  

pportDS0InjectBitError 1.3.6.1.4.1.277.1.4.2.1.96
While testing DS0 far end lpbk, setting this variable will inject a bit error into the test pattern.
OBJECT-TYPE    
  INTEGER  

pportDS0FarendLpbkType 1.3.6.1.4.1.277.1.4.2.1.97
The type of DS0 equipment to be looped back at the far end during DS0 far end testing. 1 - OCU 2 - DSU 3 - CSU.
OBJECT-TYPE    
  INTEGER  

pportDS0LpbkMode 1.3.6.1.4.1.277.1.4.2.1.98
This determines what mode the DS0 Processor will be set to. 1 - no lpbk 2 - switch lpbk 3 - far end lpbk.
OBJECT-TYPE    
  INTEGER  

pportDS0SwitchLpbkStart 1.3.6.1.4.1.277.1.4.2.1.99
This is the first DS0 in a sting of consecutive DS0's to be looped back at the switch if the DS0 processor is set to switch loopback. If it's set to far end loopback, this determines which singleton DS0 will be monitored at the receive end.
OBJECT-TYPE    
  INTEGER  

pportDS0SwitchLpbkEnd 1.3.6.1.4.1.277.1.4.2.1.100
This is the Last DS0, +1, in a sting of consecutive DS0's to be looped back at the switch if the DS0 processor is set to switch loopback. If the DS0 processor is set to far end loopback, this value will equal pportDS0SwitchLpbkStart + 1..
OBJECT-TYPE    
  INTEGER  

pportDS0FarendDS0InLpbk 1.3.6.1.4.1.277.1.4.2.1.101
This indicates the DS0 in far end loopback.
OBJECT-TYPE    
  INTEGER  

pportDS0SendTestTraffic 1.3.6.1.4.1.277.1.4.2.1.102
Enable or Disable sending DS0 2047 test pattern for DS0 far end testing.
OBJECT-TYPE    
  INTEGER  

pportOc3LoopConfig 1.3.6.1.4.1.277.1.4.2.1.103
The loopback state of the ATM IWU OC3
OBJECT-TYPE    
  INTEGER oc3NoLoop(1), oc3AtmLoop(2), oc3SerPhyLoop(3), oc3ParPhyLoop(4)  

pportOc3LoopStatus 1.3.6.1.4.1.277.1.4.2.1.104
The current loopback status of the ATM IWU OC3
OBJECT-TYPE    
  INTEGER oc3NoLoop(1), oc3AtmLoop(2), oc3SerPhyLoop(3), oc3ParPhyLoop(4)  

pportISDNIpBaseAddr 1.3.6.1.4.1.277.1.4.2.1.105
Specifies the base address used for IP Dynamic Address Assignment
OBJECT-TYPE    
  IpAddress  

pportSonetSTM1Scramble 1.3.6.1.4.1.277.1.4.2.1.106
Configured SONET/STM-1 scrambling.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

pportEFCIMarking 1.3.6.1.4.1.277.1.4.2.1.107
Configured EFCI marking for cell traffic in Topaz IOMs
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

pportAtmQOSTransmitMode 1.3.6.1.4.1.277.1.4.2.1.108
Select fix priority or weighted round-robin for cell transmission in different ATM QOS classes.
OBJECT-TYPE    
  INTEGER fix-priority(1), weighted-round-robin(2)  

pportHECMode 1.3.6.1.4.1.277.1.4.2.1.109
Configured ATM HEC single bit error correction routine.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

pportISDNChannelStatus 1.3.6.1.4.1.277.1.4.2.1.110
The ISDN call status of all the B-Channels on the pport are encoded into this 24 character, (for T1 ISDN PRI card...23B+D) or 31 character, (for E1 ISDN PRI card...30B+D ) ASCII string. The respective call state for each B-Channel is represented in its corresponding bit position. The D-Channel status is similarly encoded into the appropriate bit position (24th for T1) or (16th for E1). The encoding legend is as follows... I B-Channel is in Idle state R B-Channel is in Dialing (Ringing) state C B-Channel is in Connected (Active) state H B-Channel is in Releasing (Hanging-up) state U D-Channel is Up D D-Channel is Down
OBJECT-TYPE    
  OCTET STRING  

pportds1FarEndLoopStatus 1.3.6.1.4.1.277.1.4.2.1.111
DS1 Far End Loopback Status as commanded by the switch
OBJECT-TYPE    
  INTEGER fe-noloop(1), fe-line-loop(2), fe-payload-loop(3)  

pportds1FDLControl 1.3.6.1.4.1.277.1.4.2.1.112
Enables or Disables FDL Function for DS1 ESF pport
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

pportds1FDLPrmXmit 1.3.6.1.4.1.277.1.4.2.1.113
Enables or Disables transmission of Performance Monitoring Report (PRM) messages on the DS1 ESF FDL
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

pportds1FDLPidXmit 1.3.6.1.4.1.277.1.4.2.1.114
Enables or Disables transmission of Path ID (PID) messages on the DS1 ESF FDL
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

pportds1FDLXmitPid 1.3.6.1.4.1.277.1.4.2.1.115
Transmit Path Id to be sent on the DS1 ESF FDL. (76 bytes)
OBJECT-TYPE    
  OCTET STRING  

pportds1FDLRcvPid 1.3.6.1.4.1.277.1.4.2.1.116
The last path id message received on the DS1 ESF FDL. (76 bytes)
OBJECT-TYPE    
  OCTET STRING  

pportds1FDLRcvTsid 1.3.6.1.4.1.277.1.4.2.1.117
The last test id message received on the DS1 ESF FDL. (76 bytes)
OBJECT-TYPE    
  OCTET STRING  

pportSonetSDHFramingMode 1.3.6.1.4.1.277.1.4.2.1.118
The Framing mode for SONET/SDH port interface types.
OBJECT-TYPE    
  INTEGER sonet(1), sdh(2)  

pportds1InbandLoopType 1.3.6.1.4.1.277.1.4.2.1.119
Integer used to distinguish Inband Line loopback code sent from the switch when commanding inband line loopbacks, and reckognized by the switch when responding to remote loopback commands
OBJECT-TYPE    
  INTEGER ds1CSU(1), ds1NI(2)  

pportESFDataLinkStatus 1.3.6.1.4.1.277.1.4.2.1.120
The current status of the DS1 ESF (FDL) data link.
OBJECT-TYPE    
  INTEGER inService(1), outOfService(2)  

pportPMTcaId 1.3.6.1.4.1.277.1.4.2.1.121
This object identifies the the most recently declared pport threshold crossing alert
OBJECT-TYPE    
  INTEGER currentThresholdCVL(1), currentThresholdESL(2), currentThresholdSESL(3), currentThresholdUASL(4), currentThresholdCVP(5), currentThresholdESP(6), currentThresholdSESP(7), currentThresholdSASP(8), currentThresholdCSSP(9), currentThresholdUASP(10), currentThresholdCVS(11), currentThresholdESS(12), currentThresholdSESS(13), currentThresholdESx(14), dayThresholdCVL(15), dayThresholdESL(16), dayThresholdSESL(17), dayThresholdUASL(18), dayThresholdCVP(19), dayThresholdESP(20), dayThresholdSESP(21), dayThresholdSASP(22), dayThresholdCSSP(23), dayThresholdUASP(24), dayThresholdCVS(25), dayThresholdESS(26), dayThresholdSESS(27), dayThresholdESx(28), currentThresholdCVCPP(29), currentThresholdESCPP(30), currentThresholdSESCPP(31), currentThresholdSASCPP(32), currentThresholdUASCPP(33), dayThresholdCVCPP(34), dayThresholdESCPP(35), dayThresholdSESCPP(36), dayThresholdSASCPP(37), dayThresholdUASCPP(38), currentThresholdCVCPPFE(39), currentThresholdESCPPFE(40), currentThresholdSESCPPFE(41), currentThresholdSASCPPFE(42), currentThresholdUASCPPFE(43), dayThresholdCVCPPFE(44), dayThresholdESCPPFE(45), dayThresholdSESCPPFE(46), dayThresholdSASCPPFE(47), dayThresholdUASCPPFE(48)  

pportBchanTimerValue 1.3.6.1.4.1.277.1.4.2.1.122
This value is used on a per port basis to add a delay to answering a ISDN call of the initial Disconnect from the network. This due to the ARP cache not updating quick enough on the routers
OBJECT-TYPE    
  INTEGER  

pportAAL5CRC32Error 1.3.6.1.4.1.277.1.4.2.1.123
Number of received AAL5 packets with CRC32 errors.
OBJECT-TYPE    
  Counter  

pportAAL5CPIError 1.3.6.1.4.1.277.1.4.2.1.124
Number of received AAL5 packets with CPI errors The only valid value currently defined for the CPI field is all zeros
OBJECT-TYPE    
  Counter  

pportAAL5LengthError 1.3.6.1.4.1.277.1.4.2.1.125
Number of received AAL5 packets which satisfied one of the following error conditions: 1. number of received cells * 48 bytes - length value in trailer > 55 bytes 2. number of received cells * 48 bytes - length value in trailer < 8 bytes
OBJECT-TYPE    
  Counter  

pportAAL5ReassemblyTimerError 1.3.6.1.4.1.277.1.4.2.1.126
Number of expired reassembly timers
OBJECT-TYPE    
  Counter  

pportAAL5MaxNrSegError 1.3.6.1.4.1.277.1.4.2.1.127
Number of received AAL5 packets which exceeds the maximum allowed length
OBJECT-TYPE    
  Counter  

pportRedundancyArch 1.3.6.1.4.1.277.1.4.2.1.128
Pport redundancy architecture. Default is disabled. aps-intracard -- ports are both on same card. aps-with-resilient-uni -- ports may be on different cards, resilient UNI is used to reroute traffic. aps-intercard-trunk-backup -- ports may be on different cards, aps keeps phy layer in sync w/trunk backup.
OBJECT-TYPE    
  INTEGER disabled(1), aps-intracard(2), aps-with-resilient-uni(3), aps-with-trunk-backup(4)  

pportAPSadminDir 1.3.6.1.4.1.277.1.4.2.1.129
Provisioned APS switch-direction-mode. Default is uni- directional.
OBJECT-TYPE    
  INTEGER uni-directional(1), bi-directional(2)  

pportAPSlineType 1.3.6.1.4.1.277.1.4.2.1.130
APS line type for the pport. Writable only when pportRedundancyArch is disabled.
OBJECT-TYPE    
  INTEGER working-line(1), protection-line(2)  

pportAPSrevertiveMode 1.3.6.1.4.1.277.1.4.2.1.131
APS revertive mode. When revertive, after the condition for an automatic switchover clears, user traffic will be switched back to the working line after the pportAPSwtrPeriod expires. Default is revertive.
OBJECT-TYPE    
  INTEGER revertive(1), nonrevertive(2)  

pportAPSpairedSlotId 1.3.6.1.4.1.277.1.4.2.1.132
Slot ID of the paired-with APS pport. Writable only when pportRedundancyArch is disabled.
OBJECT-TYPE    
  INTEGER 1..16  

pportAPSpairedPportId 1.3.6.1.4.1.277.1.4.2.1.133
Pport ID of the paired-with APS pport. Writable only when pportRedundancyARch is disabled.
OBJECT-TYPE    
  INTEGER  

pportAPSsfBerThresh 1.3.6.1.4.1.277.1.4.2.1.134
Exponent N for APS Signal Failure based on BER. A line bit-error-rate above 10^-N causes an SF BER failure to be asserted. SF BER is cleared when the line BER returns to less than 10^-7.
OBJECT-TYPE    
  INTEGER 3..5  

pportAPSsdBerThresh 1.3.6.1.4.1.277.1.4.2.1.135
Exponent N for APS Signal Degrade based on BER. A line bit-error-rate above 10^-N causes an SD BER failure to be asserted. SD BER is cleared when the line BER returns to less than 10^-(N+1).
OBJECT-TYPE    
  INTEGER 6..9  

pportAPSwtrPeriod 1.3.6.1.4.1.277.1.4.2.1.136
APS wait-to-restore period. The number of minutes to wait after an automatic switch condition clears before switching back to the working line.
OBJECT-TYPE    
  INTEGER 5..12  

pportAPSprotectionLineState 1.3.6.1.4.1.277.1.4.2.1.137
Indicates the state of the protection line selector. When selected, a protection switchover has taken place and user traffic is being selected from the protection line.
OBJECT-TYPE    
  INTEGER released(1), selected(2)  

pportAPSxCommand 1.3.6.1.4.1.277.1.4.2.1.138
External switch commands. The clear command clears any previously activated external command. Manual switch is preemptable by auto-switch-requests (line failures) while forced switch is not preemptable (except if the protection line fails). Manual and forced switch from protection to working, is valid only for 1+1 mode. Exercise simulates a switchover using APS signalling without actually performing a switch to protection line.
OBJECT-TYPE    
  INTEGER clear(1), lockout-protection(2), forced-switch-w-to-p(3), forced-switch-p-to-w(4), manual-switch-w-to-p(5), manual-switch-p-to-w(6), exercise(7)  

pportAPSconfigStatus 1.3.6.1.4.1.277.1.4.2.1.139
Status of APS pport configuration. The not-configured status indicates the pport APS feature is not configured or it is a non-APS pport. The valid state indicates the pport APS function is configured and has been validated by the APS manager. The invalid state indicates that the APS manager has detected a conflict between the working line and protection line pport configurations. The user must clear the invalid state by changing the configuration of the misconfigured pport as soon as possible. Check pportAPSadminDir, pportAPSlineType, pportAPSrevertiveMode, and pportAPSwtrPeriod for any misconfigurations.
OBJECT-TYPE    
  INTEGER not-configured(1), valid(2), invalid(3)  

pportAPSOperRxStatus 1.3.6.1.4.1.277.1.4.2.1.140
The current state of the pair of APS pports with respect to the ability of the pair to Receive user traffic. When indicated as up, user traffic may be received on at least one of the ports in the APS pair.
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3)  

pportBertPattern 1.3.6.1.4.1.277.1.4.2.1.141
Pattern generated by the XBERT
OBJECT-TYPE    
  INTEGER allZeros(1), allOnes(2), oneZero(3), oneOneZeroZero(4), oneOf8(5), threeOf24(6), qRSS(7), user1Byte(8), user2Byte(9), user3Byte(10), user4Byte(11)  

pportBertUserBytes 1.3.6.1.4.1.277.1.4.2.1.142
Definition of 1,2,3 or 4 byte pattern if UserNByte selected.
OBJECT-TYPE    
  INTEGER  

pportBertErrorRate 1.3.6.1.4.1.277.1.4.2.1.143
Error rate to insert in generated pattern.
OBJECT-TYPE    
  INTEGER none(1), tenMinusThree(2), tenMinusSix(3)  

pportBertCommand 1.3.6.1.4.1.277.1.4.2.1.144
Single shot commands to the BERT.
OBJECT-TYPE    
  INTEGER start(1), stop(2), clearCounters(3), injectError(4)  

pportBertStatus 1.3.6.1.4.1.277.1.4.2.1.145
Current status of the BERT for this channel.
OBJECT-TYPE    
  INTEGER unused(1), unavailable(2), outOfFrame(3), inFrame(4)  

pportBertBitCount 1.3.6.1.4.1.277.1.4.2.1.146
The number of bits received - stops counting at 0xFFFFFFFF
OBJECT-TYPE    
  Gauge  

pportBertErrorCount 1.3.6.1.4.1.277.1.4.2.1.147
The number of bits received in error- stops counting at 0xFFFFFFFF
OBJECT-TYPE    
  Gauge  

pportds1FELoopbackControl 1.3.6.1.4.1.277.1.4.2.1.148
Enables or Disables Far end loopback control of the switch. Enabled (2) = Loop up and down commands from far end equipment will be processed. Disabled (1) - loop up and down commands from far end equipment shall be ignored. This control does not affect the switch's transmission of loopback commands to the far end
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

pportFT1DS0s 1.3.6.1.4.1.277.1.4.2.1.149
DS0 usage bitmask for Fractional T1/E1 data rates.
OBJECT-TYPE    
  DisplayString  

pportIMUXCnt 1.3.6.1.4.1.277.1.4.2.1.150
DS3 Inverse Multiplexer counter value - specifies number of idle cells to insert by the outbound process Hardware.
OBJECT-TYPE    
  INTEGER  

pportds1PMConfigThresh 1.3.6.1.4.1.277.1.4.2.1.151
The setting determines which standard is used for performance monitoring configuration thresholds
OBJECT-TYPE    
  INTEGER rfc1406(1), itu-g826(2)  

pportIdleCellType 1.3.6.1.4.1.277.1.4.2.1.152
The setting determines the type of Idle/unassigned cell transmitted by the pport. 1 -- ATM Forum CLP=0, payload=6A 2 -- ITU CLP=1, payload=6A
OBJECT-TYPE    
  INTEGER atmforum(1), itu(2)  

pportATMTcaInHECErrorUAlertPeriod 1.3.6.1.4.1.277.1.4.2.1.153
ATM tca ingress HEC error uncorrectable alert period (in min.).
OBJECT-TYPE    
  INTEGER  

pportATMTcaInHECErrorUThresh 1.3.6.1.4.1.277.1.4.2.1.154
ATM tca ingress HEC error uncorrectable threshold.
OBJECT-TYPE    
  INTEGER  

pportATMTcaEBufOverflowCBRAlertPeriod 1.3.6.1.4.1.277.1.4.2.1.155
ATM tca egress buffer overflow CBR Alert period (in min)
OBJECT-TYPE    
  INTEGER  

pportATMTcaEBufOverflowCBRThresh 1.3.6.1.4.1.277.1.4.2.1.156
ATM tca egress buffer overflow CBR threshold.
OBJECT-TYPE    
  INTEGER  

pportATMTcaEBufOverflowABRAlertPeriod 1.3.6.1.4.1.277.1.4.2.1.157
ATM tca egress buffer overflow ABR alert period (in min)
OBJECT-TYPE    
  INTEGER  

pportATMTcaEBufOverflowABRThresh 1.3.6.1.4.1.277.1.4.2.1.158
ATM tca egress buffer overflow ABR threshold.
OBJECT-TYPE    
  INTEGER  

pportATMTcaEBufOverflowVBR1AlertPeriod 1.3.6.1.4.1.277.1.4.2.1.159
ATM tca egress buffer overflow VBR1 alert period (in min)
OBJECT-TYPE    
  INTEGER  

pportATMTcaEBufOverflowVBR1Thresh 1.3.6.1.4.1.277.1.4.2.1.160
ATM tca egress buffer overflow VBR1 threshold.
OBJECT-TYPE    
  INTEGER  

pportATMTcaEBufOverflowVBR2AlertPeriod 1.3.6.1.4.1.277.1.4.2.1.161
ATM tca egress buffer overflow VBR2 alert period (in min)
OBJECT-TYPE    
  INTEGER  

pportATMTcaEBufOverflowVBR2Thresh 1.3.6.1.4.1.277.1.4.2.1.162
ATM tca egress buffer overflow VBR2 threshold.
OBJECT-TYPE    
  INTEGER  

pportATMTcaInFramerFIFOOverflowAlertPeriod 1.3.6.1.4.1.277.1.4.2.1.163
ATM tca ingress framer FIFO overflow alert period (in min)
OBJECT-TYPE    
  INTEGER  

pportATMTcaInFramerFIFOOverflowThresh 1.3.6.1.4.1.277.1.4.2.1.164
ATM tca ingress framer FIFO overflow threshold.
OBJECT-TYPE    
  INTEGER  

pportATMTcaELookupFailureAlertPeriod 1.3.6.1.4.1.277.1.4.2.1.165
ATM tca egress lookup failure alert period (in min)
OBJECT-TYPE    
  INTEGER  

pportATMTcaELookupFailureThresh 1.3.6.1.4.1.277.1.4.2.1.166
ATM tca egress lookup failure threshold.
OBJECT-TYPE    
  INTEGER  

pportATMTcaEnable 1.3.6.1.4.1.277.1.4.2.1.167
ATM tca port enable.
OBJECT-TYPE    
  INTEGER  

pportATMTcaId 1.3.6.1.4.1.277.1.4.2.1.168
This object identifies the the most recently declared pport ATM threshold crossing alert
OBJECT-TYPE    
  INTEGER ingressHECErrorUThresholdC(1), egressCBRBufferOverflowC(2), egressABRBufferOverflowC(3), egressVBR1BufferOverflowC(4), egressVBR2BufferOverflowC(5), ingressFramerFIFOOverflowC(6), egressLookupFailureC(7)  

pportFethAdminMacAddr 1.3.6.1.4.1.277.1.4.2.1.169
The configured MAC address to use for this Fast Ethernet port. Setting this to all zeros will force the port to use the burned in MAC address.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

pportFethOperMacAddr 1.3.6.1.4.1.277.1.4.2.1.170
The actual MAC address in use for this Fast Ethernet port.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

pportConfigAlarmSoakTime 1.3.6.1.4.1.277.1.4.2.1.171
This is the soak time for configurable alarms. An alarm of this type must persist for this period before it is declared. The time is specified in millseconds units.
OBJECT-TYPE    
  INTEGER 0..65535  

pportConfigAlarmClearTime 1.3.6.1.4.1.277.1.4.2.1.172
This is the soak time for configurable alarms. An alarm of this type must remain clear for this period before it is declared to be cleared. The time is specified in millseconds units.
OBJECT-TYPE    
  INTEGER 0..65535  

pportFethPortCapability 1.3.6.1.4.1.277.1.4.2.1.173
Selection for the speed (10/100) and mode (half/full duplex) of operation for Fast Ethernet ports.
OBJECT-TYPE    
  INTEGER fullDuplex100Mbps(1), halfDuplex100Mbps(2), fullDuplex10Mbps(3), halfDuplex10Mbps(4)  

pportVpshapingDiscardCellCount 1.3.6.1.4.1.277.1.4.2.1.174
Cells discarded due to buffer overflow on this pport because of traffic shaping.
OBJECT-TYPE    
  INTEGER  

pportTrafficShaperTable 1.3.6.1.4.1.277.1.4.3
A list of Parameters assigned to the 16 traffic shaper parameter conbinations of each pport of the ATM-IWU.
OBJECT-TYPE    
  SEQUENCE OF  
    PportTrafficShaperEntry

pportTrafficShaperEntry 1.3.6.1.4.1.277.1.4.3.1
Information of a single system reference clock source.
OBJECT-TYPE    
  PportTrafficShaperEntry  

pportTrafficShaperIndex 1.3.6.1.4.1.277.1.4.3.1.1
A positive integer to identify an entry in the pportTrafficShaperTable. The ATM-IWU and CS cards support exactly 16 shapers.
OBJECT-TYPE    
  INTEGER 1..16  

pportTrafficShaperPriority 1.3.6.1.4.1.277.1.4.3.1.2
The priority of the Shaper. Channels tied to a Shaper are served only if no higher priority Shapers await service. 0 ist the highest, 15 the lowest priority.
OBJECT-TYPE    
  INTEGER 0..15  

pportTrafficShaperCellRatioDividend 1.3.6.1.4.1.277.1.4.3.1.3
The quotient of pportTrafficShaperCellRatioDividend and pportTrafficShaperCellRatioDivisor determines the average rate allocated to the shaper. The shaper serves portTrafficShaperCellRatioDividend cells in pportTrafficShaperCellRatioDivisor cell times.
OBJECT-TYPE    
  INTEGER 0..255  

pportTrafficShaperCellRatioDivisor 1.3.6.1.4.1.277.1.4.3.1.4
See pportTrafficShaperCellRatioDividend
OBJECT-TYPE    
  INTEGER 1..16777215  

pportTrafficShaperPeak 1.3.6.1.4.1.277.1.4.3.1.5
The peak cell rate. It defines the minimum gap (in cell units) between emission of any consecutive cells in this channel.
OBJECT-TYPE    
  INTEGER 0..255  

pportTrafficShaperCredit 1.3.6.1.4.1.277.1.4.3.1.6
Defines the maximum number of credits that can be accumulated by a shaper. This is equivalent to the maximum burst allowed at the peak rate.
OBJECT-TYPE    
  INTEGER 0..255  

lport 1.3.6.1.4.1.277.1.5
OBJECT IDENTIFIER    

nodePsBStatusChange 1.3.6.1.4.1.277.1.5
This trap indicates that the power supply B has changed state (toggled between up and down states).
TRAP-TYPE    
  nodePsBStatus  

lportTable 1.3.6.1.4.1.277.1.5.1
A list of logical port entries. The number of entries is given by the value of ifNumber in MIB-II.
OBJECT-TYPE    
  SEQUENCE OF  
    LportEntry

lportEntry 1.3.6.1.4.1.277.1.5.1.1
The logical port entry contains objects relevant to a logical port.
OBJECT-TYPE    
  LportEntry  

lportIfIndex 1.3.6.1.4.1.277.1.5.1.1.1
The ifIndex value of the corresponding ifEntry.
OBJECT-TYPE    
  Index  

lportSlotId 1.3.6.1.4.1.277.1.5.1.1.2
The slot number of the board the port is on.
OBJECT-TYPE    
  INTEGER  

lportPportId 1.3.6.1.4.1.277.1.5.1.1.3
The physical port number of the interface on the board.
OBJECT-TYPE    
  INTEGER  

lportId 1.3.6.1.4.1.277.1.5.1.1.4
The logical port number of the interface on the physical port. A logical port can be uniquely identified in a Cascade network as { NodeId.lportSlotId.lportPportId.lportId }. lportId is defaulted to 1 (i.e., one-to-one mapping between the physical port and the logical port such as local V.35 or carrier) except the following cases: - For ufr, nfr and trk logical port, it indicates the bundle number for fractional T1 or 24-bundle T1. - For pdntrk logical port, it indicates the dlci over the PDN. Note that pdntrk is not allowed on fractional T1 or 24-bundle T1 physical port.
OBJECT-TYPE    
  INTEGER  


lportProtocol 1.3.6.1.4.1.277.1.5.1.1.6
The data link protocol running on the logical port.
OBJECT-TYPE    
  INTEGER nfr(1), fradPPPto1294(2), smds(3), atm(4), isdndchan(5), dirmgmttrk(7), smdsoptmgmt(8), atmAAL1(10)  

lportSignal 1.3.6.1.4.1.277.1.5.1.1.7
The user-network signalling capability for SVC and DLCMI of the logical port. Note that this only applies to fr protocol port.
OBJECT-TYPE    
  INTEGER dce(1), dte(2), nni(3)  

lportFt1Ds0s 1.3.6.1.4.1.277.1.5.1.1.8
The bit mask indicating the DS0s for the fractional T1/E1 logical port which must be a subset of the corresponding pportDs1Ds0s. It's represented by a 32-bit hex char string.
OBJECT-TYPE    
  OCTET STRING  

lportGlobalDlci 1.3.6.1.4.1.277.1.5.1.1.9
The global DLCI correspondent to the interface if the DLCI is globally significant in the network. Note that this object is read-write only during creation, and read-only after creation.
OBJECT-TYPE    
  INTEGER  

lportDlcmiStd 1.3.6.1.4.1.277.1.5.1.1.10
This variable states which Data Link Connection Management scheme is active (and by implication, what DLCI it uses) on the Frame Relay interface.
OBJECT-TYPE    
  INTEGER disabled(1), lmiRev1(2), ansiT1-617-D(3), ccittQ-933-A(4), autodetect(5), ansiT1-617-B(6)  

lportDlciAddrFmt 1.3.6.1.4.1.277.1.5.1.1.11
This variable states which address format is in use on the Frame Relay interface.
OBJECT-TYPE    
  INTEGER q922(1)  

lportDlciAddrLen 1.3.6.1.4.1.277.1.5.1.1.12
This variable states which address length in octets. In the case of Q922 format, the length indicates the entire length of the address including the control portion.
OBJECT-TYPE    
  INTEGER two-octets-10-bits(1), three-octets-10-bits(2), three-octets-16-bits(3), four-octets-17-bits(4), four-octets-23-bits(5)  

lportMaxFramesize 1.3.6.1.4.1.277.1.5.1.1.13
The maximum frame size supported on the interface. Currently it's not used.
OBJECT-TYPE    
  INTEGER  

lportDceVerifTimer 1.3.6.1.4.1.277.1.5.1.1.14
The polling verification timer (secs) on the DCE interface. If the port is configured as a DXI/SNI, then this MIB object defines the heartbeat poll timer setting.
OBJECT-TYPE    
  INTEGER  

lportDceErrorThresh 1.3.6.1.4.1.277.1.5.1.1.15
The error threshold on the DCE interface. If the port is configured as a DXI/SNI, then this MIB object defines the heartbeat poll No Ack threshold setting.
OBJECT-TYPE    
  INTEGER  

lportDceEventCount 1.3.6.1.4.1.277.1.5.1.1.16
The monitored events count on the DCE interface.
OBJECT-TYPE    
  INTEGER  

lportDteErrorThresh 1.3.6.1.4.1.277.1.5.1.1.17
The error threshold on the DTE interface.
OBJECT-TYPE    
  INTEGER  

lportDteEventCount 1.3.6.1.4.1.277.1.5.1.1.18
The monitored events count on the DTE interface.
OBJECT-TYPE    
  INTEGER  

lportDtePollTimer 1.3.6.1.4.1.277.1.5.1.1.19
The link status polling timer (secs) on the DTE interface.
OBJECT-TYPE    
  INTEGER  

lportDteFullCounter 1.3.6.1.4.1.277.1.5.1.1.20
The full status polling counter on the DTE interface.
OBJECT-TYPE    
  INTEGER  

lportDteMulticast 1.3.6.1.4.1.277.1.5.1.1.21
The multicast capability of the interface.
OBJECT-TYPE    
  INTEGER one-way(1), two-way(2), m-way(3)  

lportTrkRnode 1.3.6.1.4.1.277.1.5.1.1.22
Node at the other end of the trunk. This object is read-write only during lport creation, and read-only thereafter.
OBJECT-TYPE    
  IpAddress  

lportTrkRlport 1.3.6.1.4.1.277.1.5.1.1.23
Logical port (IfIndex) at the other end of the trunk. This
OBJECT-TYPE    
  INTEGER  

lportCongestState 1.3.6.1.4.1.277.1.5.1.1.24
Congestion State for the logical port.
OBJECT-TYPE    
  INTEGER normal(1), mild(2), severe(3), critical(4)  

lportQP1Len 1.3.6.1.4.1.277.1.5.1.1.25
Priority-1 queue length (number of packets) in xmit buffer.
OBJECT-TYPE    
  INTEGER  

lportQP2Len 1.3.6.1.4.1.277.1.5.1.1.26
Priority-2 queue length (number of packets) in xmit buffer.
OBJECT-TYPE    
  INTEGER  

lportQP3Len 1.3.6.1.4.1.277.1.5.1.1.27
Priority-3 queue length (number of packets) in xmit buffer.
OBJECT-TYPE    
  INTEGER  

lportQP4Len 1.3.6.1.4.1.277.1.5.1.1.28
Priority-4 queue length (number of packets) in xmit buffer.
OBJECT-TYPE    
  INTEGER  

lportErrTime 1.3.6.1.4.1.277.1.5.1.1.29
The value of sysUpTime at which the last error was detected.
OBJECT-TYPE    
  TimeTicks  

lportErrType 1.3.6.1.4.1.277.1.5.1.1.30
The type of error that was last seen on this interface.
OBJECT-TYPE    
  INTEGER short-frame(1), hdlc-abort(2), residual-bit(3), crc-Error(4), rcv-Long(5), rcv-overrun(6), tx-underrun(7), unknownError(8), illegalDLCI(9), unknownDLCI(10), dlcmiProtoErr(11), dlcmiUnknownIE(12), dlcmiSequenceErr(13), dlcmiUnknownRpt(14), unknownProt(15), discardFW(16), discardRange(17), discardPortMismatch(18), discardIllegalLen(19)  

lportErrData 1.3.6.1.4.1.277.1.5.1.1.31
An octet string containing as much of the error packet as possible. As a minimum, it must contain the Q.922 Address or as much as was delivered. It is desirable to include all information up to the PDU.
OBJECT-TYPE    
  OCTET STRING  

lportDiagTestId 1.3.6.1.4.1.277.1.5.1.1.32
Identification for the diagnostics tests to be run.
OBJECT-TYPE    
  INTEGER  

lportDiagTestRuns 1.3.6.1.4.1.277.1.5.1.1.33
Number of passes of the diagnostics tests to be run. The default value is 1.
OBJECT-TYPE    
  INTEGER  

lportDataRate 1.3.6.1.4.1.277.1.5.1.1.34
An estimate of the logical port's data rate in bits per second.
OBJECT-TYPE    
  INTEGER  

lportTrkStatus 1.3.6.1.4.1.277.1.5.1.1.35
The current state of the trunk. The btdefined state only applies to backup trunks.
OBJECT-TYPE    
  INTEGER nattempt(1), ninit(2), n2way(3), nexstart(4), nexchange(5), nloading(6), nfull(7), btdefined(9)  

lportSevCongests 1.3.6.1.4.1.277.1.5.1.1.36
The cumulative number of times that the lport's congestion state has changed from mildly-congested to severely-congested since the last reset.
OBJECT-TYPE    
  INTEGER  

lportAbsCongests 1.3.6.1.4.1.277.1.5.1.1.37
The cumulative number of times that the lport's congestion state has changed from severely-congested to absolutely- congested since the last reset.
OBJECT-TYPE    
  INTEGER  

lportTrkOverhead 1.3.6.1.4.1.277.1.5.1.1.38
An estimate of the overhead (headers and internal control messages) in trunking user data in terms of a percentage of the configured trunk bandwidth.
OBJECT-TYPE    
  INTEGER  

lportTrkUtil 1.3.6.1.4.1.277.1.5.1.1.39
An estimate of the real utilization of the trunk bandwidth in terms of a percentage of the configured trunk bandwidth.
OBJECT-TYPE    
  INTEGER  

lportVAvailbw 1.3.6.1.4.1.277.1.5.1.1.40
Currently available virtual trunk bandwidth.
OBJECT-TYPE    
  INTEGER  

lportTrkLastTimeChange 1.3.6.1.4.1.277.1.5.1.1.41
The sysUpTime value when the trunk was last changed to the current status.
OBJECT-TYPE    
  TimeTicks  

lportCongestRate 1.3.6.1.4.1.277.1.5.1.1.42
The rate (%) of entering severely or absolutely congested states in the last one minute interval.
OBJECT-TYPE    
  INTEGER  

lportCongestRateThresh 1.3.6.1.4.1.277.1.5.1.1.43
The alert threshold (%) for the CongestRate; trap will be sent when exceeded.
OBJECT-TYPE    
  INTEGER  

lportDiagState 1.3.6.1.4.1.277.1.5.1.1.44
The current state of the diagnostic on this logical port.
OBJECT-TYPE    
  INTEGER active(1)  

lportDiagOptionStr 1.3.6.1.4.1.277.1.5.1.1.45
Optional parameters to the diagnostic.
OBJECT-TYPE    
  OCTET STRING  

lportDiagPassCount 1.3.6.1.4.1.277.1.5.1.1.46
Number of successful diagnostic passes.
OBJECT-TYPE    
  INTEGER  

lportDiagFailCount 1.3.6.1.4.1.277.1.5.1.1.47
Number of failed diagnostic passes.
OBJECT-TYPE    
  INTEGER  

lportDiagResultStr 1.3.6.1.4.1.277.1.5.1.1.48
Description of last diagnostic failure.
OBJECT-TYPE    
  DisplayString  

lportDs0BitStuff 1.3.6.1.4.1.277.1.5.1.1.49
Is bit stuffing enabled on this lport?
OBJECT-TYPE    
  INTEGER bit-stuffing(1)  

lportErrorThreshold 1.3.6.1.4.1.277.1.5.1.1.50
The per minute error threshold before a link error trap is sent.
OBJECT-TYPE    
  INTEGER  

lportUnsyncBandwidth 1.3.6.1.4.1.277.1.5.1.1.51
The accumulated allocated/deallocated bandwidth which has not been propagated by OSPF yet.
OBJECT-TYPE    
  INTEGER  

lportDTEInStatusFrames 1.3.6.1.4.1.277.1.5.1.1.52
The number of LMI STATUS frames received from the DCE since the last system reset. The count includes link integrity verification frames only.
OBJECT-TYPE    
  Counter  

lportDTEInFullStatusFrames 1.3.6.1.4.1.277.1.5.1.1.53
The number of LMI Full STATUS frames received from the DTE since the last system reset.
OBJECT-TYPE    
  Counter  

lportDTEInAsyncStatusFrames 1.3.6.1.4.1.277.1.5.1.1.54
The number of asynchronous LMI Status frames received from the DTE since the last system reset. For LMI Rev 1, these are Update STATUS frames. For ANSI Annex D and CCITT Annex A these are Asynchronous STATUS frames.
OBJECT-TYPE    
  Counter  

lportDTEInErrorFrames 1.3.6.1.4.1.277.1.5.1.1.55
The number of LMI frames received containing protocol errors.
OBJECT-TYPE    
  Counter  

lportDTEOutPollFrames 1.3.6.1.4.1.277.1.5.1.1.56
The number of LMI Status Enquiry frames transmitted since the last system reset.
OBJECT-TYPE    
  Counter  

lportDTEPollErrorCounts 1.3.6.1.4.1.277.1.5.1.1.57
The number of DTE in-channel signaling link reliability errors (i.e. LMI Status Enquiry frames that were not responded to, sequence number errors) since the last system reset.
OBJECT-TYPE    
  Counter  

lportDTEFailCounts 1.3.6.1.4.1.277.1.5.1.1.58
The number of times since the last system reset LMI has declared the DTE side of the link down due to excessive errors.
OBJECT-TYPE    
  Counter  

lportDTEFailReason 1.3.6.1.4.1.277.1.5.1.1.59
The LMI failure reason. If the rate of LMI detected errors exceeds the threshold, this contains the cause of the most recent error.
OBJECT-TYPE    
  INTEGER dte-bad-Nr(1), dte-timeout(2), prot-error(3)  

lportDTEOperStatus 1.3.6.1.4.1.277.1.5.1.1.60
The operational status of the DTE side of LMI on this link.
OBJECT-TYPE    
  INTEGER up(1), down(2)  

lportDCEInPollFrames 1.3.6.1.4.1.277.1.5.1.1.61
The number of LMI poll frames received from the DTE since the last system reset.
OBJECT-TYPE    
  Counter  

lportDCEInErrorFrames 1.3.6.1.4.1.277.1.5.1.1.62
The number of LMI frames received containing protocol errors.
OBJECT-TYPE    
  Counter  

lportDCEOutStatusFrames 1.3.6.1.4.1.277.1.5.1.1.63
The number of LMI STATUS frames transmitted since the last system reset. The count includes link integrity verification frames only.
OBJECT-TYPE    
  Counter  

lportDCEOutFullStatusFrames 1.3.6.1.4.1.277.1.5.1.1.64
The number of LMI Full STATUS frames transmitted since the last system reset.
OBJECT-TYPE    
  Counter  

lportDCEOutAsyncStatusFrames 1.3.6.1.4.1.277.1.5.1.1.65
The number of asynchronous LMI Status frames transmitted since the last system reset. For LMI Rev 1, these are Update STATUS frames. For ANSI Annex D and CCITT Annex A these are Asynchronous STATUS frames.
OBJECT-TYPE    
  Counter  

lportDCEPollErrorCounts 1.3.6.1.4.1.277.1.5.1.1.66
The number of DCE in-channel signaling link reliability errors (i.e. timeouts waiting for LMI Status Enquiry frames, sequence number errors) since the last system reset.
OBJECT-TYPE    
  Counter  

lportDCEFailCounts 1.3.6.1.4.1.277.1.5.1.1.67
The number of times since the last system reset LMI has declared the DCE side of the link down due to excessive errors.
OBJECT-TYPE    
  Counter  

lportDCEFailReason 1.3.6.1.4.1.277.1.5.1.1.68
The LMI failure reason. If the rate of LMI detected errors exceeds the threshold, this contains the cause of the most recent error.
OBJECT-TYPE    
  INTEGER dce-bad-Nr(1), dce-timeout(2), prot-error(3)  

lportDCEOperStatus 1.3.6.1.4.1.277.1.5.1.1.69
The operational status of the DCE side of LMI on this link.
OBJECT-TYPE    
  INTEGER up(1), down(2)  

lportDCEOperDlcmiStd 1.3.6.1.4.1.277.1.5.1.1.70
This variable states which Data Link Connection Management scheme is actually being run on this link. This is used for DCE links configured for AutoDetect and indicates the LMI standard used in the last poll received from the DTE.
OBJECT-TYPE    
  INTEGER unknown(1), lmiRev1(2), ansiT1-617-D(3), ccittQ-933-A(4), reserved(5), ansiT1-617-B(6)  

lportLMIInErrorFrames 1.3.6.1.4.1.277.1.5.1.1.71
The number of total frames received with an error. For NNI links this is the sum of lportDTEInErrorFrames and lportDCEInErrorFrames.
OBJECT-TYPE    
  Counter  

lportDCEnN4 1.3.6.1.4.1.277.1.5.1.1.72
This variable specifies the maximum number of LMI Status Enquiry frames that can be received from a DTE within time interval lportDCEnT3. This is only valid on lports using LMIREV1.
OBJECT-TYPE    
  INTEGER  

lportDCEnT3 1.3.6.1.4.1.277.1.5.1.1.73
This variable specifies the time interval (secs) used to determine if lportDCEnN4 an excess number (lportDCEnN4) of Status Enquiry messages are received. This is only valid on lports using LMIREV1.
OBJECT-TYPE    
  INTEGER  

lportXmitLatencyThreshold 1.3.6.1.4.1.277.1.5.1.1.74
Outbound frames are allowed on the transmit commit queue when the commit queue falls below this threshold (in microseconds).
OBJECT-TYPE    
  INTEGER  

lportXmitRefillPriority0Percentage 1.3.6.1.4.1.277.1.5.1.1.75
Percentage of time the transmit queue is refilled in priority order 0, 1, 2, 3.
OBJECT-TYPE    
  INTEGER  

lportXmitRefillPriority1Percentage 1.3.6.1.4.1.277.1.5.1.1.76
Percentage of time the transmit queue is refilled in priority order 1, 2, 3, 0.
OBJECT-TYPE    
  INTEGER  

lportXmitRefillPriority2Percentage 1.3.6.1.4.1.277.1.5.1.1.77
Percentage of time the transmit queue is refilled in priority order 2, 3, 0, 1.
OBJECT-TYPE    
  INTEGER  

lportXmitRefillPriority3Percentage 1.3.6.1.4.1.277.1.5.1.1.78
Percentage of time the transmit queue is refilled in priority order 3, 0, 1, 2.
OBJECT-TYPE    
  INTEGER  

lportXmitDiscardLow 1.3.6.1.4.1.277.1.5.1.1.79
Priority holding queue low water discard threshold. Discarding stops when holding queue hits this level.
OBJECT-TYPE    
  INTEGER  

lportSevereThreshold 1.3.6.1.4.1.277.1.5.1.1.80
Severe congestion level. Outbound red and amber packets are discarded when the transmit queue hits this threshold.
OBJECT-TYPE    
  INTEGER  

lportMildThreshold 1.3.6.1.4.1.277.1.5.1.1.81
Mild congestion level. Outbound red packets are discarded when the transmit queue hits this threshold.
OBJECT-TYPE    
  INTEGER  

lportTrkKeepAliveTimer 1.3.6.1.4.1.277.1.5.1.1.86
Send a keep-alive packet after this many seconds. These packets are sent on trunk links only. The range is 0 thru 15, with zero meaning the keep-alive protocol is disabled. The default is one.
OBJECT-TYPE    
  INTEGER  

lportTrkKeepAliveErrorThreshold 1.3.6.1.4.1.277.1.5.1.1.87
Declare the interface down after this many keep-alive packets in a row are missed. The default is five.
OBJECT-TYPE    
  INTEGER  

lportIgCutThruStatus 1.3.6.1.4.1.277.1.5.1.1.88
Enable ingress cut-thru on this user lport. Default is disabled.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

lportEgCutThruStatus 1.3.6.1.4.1.277.1.5.1.1.89
Enable egress cut-thru on this user lport. Default is disabled.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

lportEgCutThruThresh 1.3.6.1.4.1.277.1.5.1.1.90
Egress cut thru threshold - start transmitting a frame on a user port after this many segments have arrived.
OBJECT-TYPE    
  INTEGER  

lportFrameRelayTrkEnable 1.3.6.1.4.1.277.1.5.1.1.91
Allow Frame Relay Trunks on the user link.
OBJECT-TYPE    
  INTEGER allowed(1), not-allowed(2)  

lportSmdsSsiIf 1.3.6.1.4.1.277.1.5.1.1.92
The interface number of the SSI which this DXI/SNI is multiplexed to.
OBJECT-TYPE    
  INTEGER  

lportSmdsSsiSlot 1.3.6.1.4.1.277.1.5.1.1.93
The slot of the SSI which this DXI/SNI is multiplexed to.
OBJECT-TYPE    
  INTEGER  

lportSmdsScrnId 1.3.6.1.4.1.277.1.5.1.1.94
The ID of address screen for this interface.
OBJECT-TYPE    
  INTEGER  

lportSmdsIaScrnOp 1.3.6.1.4.1.277.1.5.1.1.95
Individual address screen operation.
OBJECT-TYPE    
  INTEGER allow(1), disallow(2)  

lportSmdsGaScrnOp 1.3.6.1.4.1.277.1.5.1.1.96
Group address screen operation.
OBJECT-TYPE    
  INTEGER allow(1), disallow(2)  

lportSmdsIaScrnMap 1.3.6.1.4.1.277.1.5.1.1.97
The individual address screen member bit map. For set request, the first byte is the operation : 1 for deleting, 2 for adding. The following bytes are the bit map. The bit position of each bit in this bit map represent a screen member ID. The most significant bit is corresponding to group address ID 1. For get response, The whole string is the bit map.
OBJECT-TYPE    
  OCTET STRING  

lportSmdsGaScrnMap 1.3.6.1.4.1.277.1.5.1.1.98
The group address screen member bit map. For set request, the first byte is the operation : 1 for deleting, 2 for adding. The following bytes are the bit map. The bit position of each bit in this bit map represent a screen member ID. The most significant bit is corresponding to group address ID 1. For get response, The whole string is the bit map.
OBJECT-TYPE    
  OCTET STRING  

lportSmdsTrkAddr 1.3.6.1.4.1.277.1.5.1.1.99
SMDS address. For SSI feeder port, this address is the local address of all SMDS optimim paths associated with this SSI feeder port. For SSI Optimum path port, this address is the remote address of this SSI optimum path. The 4 most significant bits are 1100. The following 4 bits are 0001. The following 5 bytes are the 10 digits number in BCD format. The following 16 bits are padded with 1's
OBJECT-TYPE    
  OCTET STRING  

lportSmdsCrc 1.3.6.1.4.1.277.1.5.1.1.100
CRC which CPE generates.
OBJECT-TYPE    
  INTEGER crc16(1), crc32(2)  

lportSmdsCpePoll 1.3.6.1.4.1.277.1.5.1.1.101
Whether CPE supports heart beat poll or not.
OBJECT-TYPE    
  INTEGER nopoll(1), poll(2)  

lportSmdsPduCheck 1.3.6.1.4.1.277.1.5.1.1.102
turn of/off the detailed SIP3 PDU error checking.
OBJECT-TYPE    
  INTEGER on(1)  

lportSmdsCntOutFrDxi2HbPolls 1.3.6.1.4.1.277.1.5.1.1.103
Number of DXI2 heart beat poll frames transmitted.
OBJECT-TYPE    
  Counter  

lportSmdsCntOutByteDxi2HbPolls 1.3.6.1.4.1.277.1.5.1.1.104
Total number of octets in DXI2 heart beat poll frames transmitted.
OBJECT-TYPE    
  Counter  

lportSmdsCntInFrDxi2HbPolls 1.3.6.1.4.1.277.1.5.1.1.105
Number of DXI2 heart beat poll frames received.
OBJECT-TYPE    
  Counter  

lportSmdsCntInByteDxi2HbPolls 1.3.6.1.4.1.277.1.5.1.1.106
Total number of octets in DXI2 heart beat poll frames received.
OBJECT-TYPE    
  Counter  

lportSmdsCntOutFrSip3s 1.3.6.1.4.1.277.1.5.1.1.107
Number of SIP3 frames transmitted.
OBJECT-TYPE    
  Counter  

lportSmdsCntOutByteSip3s 1.3.6.1.4.1.277.1.5.1.1.108
Total number of octets in SIP3 frames transmitted.
OBJECT-TYPE    
  Counter  

lportSmdsCntInFrSip3s 1.3.6.1.4.1.277.1.5.1.1.109
Number of SIP3 frames received.
OBJECT-TYPE    
  Counter  

lportSmdsCntInByteSip3s 1.3.6.1.4.1.277.1.5.1.1.110
Total number of octets in SIP3 frames received.
OBJECT-TYPE    
  Counter  

lportSmdsCntDxi2LinkIdInvalids 1.3.6.1.4.1.277.1.5.1.1.111
Number of instances that DXI2 link ID is invalid.
OBJECT-TYPE    
  Counter  

lportSmdsCntDxi2StationIdInvalids 1.3.6.1.4.1.277.1.5.1.1.112
Number of instances that DXI2 station ID is invalid.
OBJECT-TYPE    
  Counter  

lportSmdsCntDxi2CrInvalids 1.3.6.1.4.1.277.1.5.1.1.113
Number of instances that DXI2 command/response field is invalid.
OBJECT-TYPE    
  Counter  

lportSmdsCntDxi2AeInvalids 1.3.6.1.4.1.277.1.5.1.1.114
Number of instances that DXI2 address extension field is invalid.
OBJECT-TYPE    
  Counter  

lportSmdsCntDxi2CtrlInvalids 1.3.6.1.4.1.277.1.5.1.1.115
Number of instances that DXI2 control field is invalid.
OBJECT-TYPE    
  Counter  

lportSmdsCntDxi2FrameSizeErrors 1.3.6.1.4.1.277.1.5.1.1.116
Number of instances there is a DXI2 frame size error.
OBJECT-TYPE    
  Counter  

lportSmdsCntSip3RsvdInvalids 1.3.6.1.4.1.277.1.5.1.1.117
Number of instances that SIP3 reserved field in header is invalid.
OBJECT-TYPE    
  Counter  

lportSmdsCntSip3BetagMismatchs 1.3.6.1.4.1.277.1.5.1.1.118
Number of instances that SIP3 BE tag is not macthed.
OBJECT-TYPE    
  Counter  

lportSmdsCntSip3BasizeIncorrects 1.3.6.1.4.1.277.1.5.1.1.119
Number of instances that SIP3 BA size is incorrect.
OBJECT-TYPE    
  Counter  

lportSmdsCntSip3BasizeInvalids 1.3.6.1.4.1.277.1.5.1.1.120
Number of instances that SIP3 BA size is invalid.
OBJECT-TYPE    
  Counter  

lportSmdsCntSip3DaTypeInvalids 1.3.6.1.4.1.277.1.5.1.1.121
Number of instances that SIP3 destination address type is invalid.
OBJECT-TYPE    
  Counter  

lportSmdsCntSip3DaInvalids 1.3.6.1.4.1.277.1.5.1.1.122
Number of instances that SIP3 destination address is invalid.
OBJECT-TYPE    
  Counter  

lportSmdsCntSip3SaTypeInvalids 1.3.6.1.4.1.277.1.5.1.1.123
Number of instances that SIP3 source address type is invalid.
OBJECT-TYPE    
  Counter  

lportSmdsCntSip3SaInvalids 1.3.6.1.4.1.277.1.5.1.1.124
Number of instances that SIP3 source address is invalid.
OBJECT-TYPE    
  Counter  

lportSmdsCntSip3BasizeMismatchs 1.3.6.1.4.1.277.1.5.1.1.125
Number of instances that SIP3 BA sizes in the header and trailer are not matched.
OBJECT-TYPE    
  Counter  

lportSmdsCntSip3HeLenInvalids 1.3.6.1.4.1.277.1.5.1.1.126
Number of instances that SIP3 header extension length is invalid.
OBJECT-TYPE    
  Counter  

lportSmdsCntSip3HeVersionInvalids 1.3.6.1.4.1.277.1.5.1.1.127
Number of instances that SIP3 header extension version is invalid.
OBJECT-TYPE    
  Counter  

lportSmdsCntSip3HeCarrierInvalids 1.3.6.1.4.1.277.1.5.1.1.128
Number of instances that SIP3 header extension carrier is invalid.
OBJECT-TYPE    
  Counter  

lportSmdsCntSip3Crc32Errors 1.3.6.1.4.1.277.1.5.1.1.129
Number of SIP3 CRC errors.
OBJECT-TYPE    
  Counter  

lportSmdsCntSip3TRsvdInvalids 1.3.6.1.4.1.277.1.5.1.1.130
Number of instances that SIP3 reserved field in trailer is invalid.
OBJECT-TYPE    
  Counter  

lportSmdsCntSaNotFounds 1.3.6.1.4.1.277.1.5.1.1.131
Number of instances that source address not found.
OBJECT-TYPE    
  Counter  

lportSmdsCntSaValidationFails 1.3.6.1.4.1.277.1.5.1.1.132
Number of instances that source address validation failed.
OBJECT-TYPE    
  Counter  

lportSmdsCntSaDaOnSamePorts 1.3.6.1.4.1.277.1.5.1.1.133
Number of instances that source address and destination addresses are on the same port.
OBJECT-TYPE    
  Counter  

lportSmdsCntDaSsiMismacths 1.3.6.1.4.1.277.1.5.1.1.134
Obsolete.
OBJECT-TYPE    
  Counter  

lportSmdsCntSsiProvisionErrors 1.3.6.1.4.1.277.1.5.1.1.135
Obsolete.
OBJECT-TYPE    
  Counter  

lportSmdsCntDstIaNotFounds 1.3.6.1.4.1.277.1.5.1.1.136
Number of instances that destination individual address not found.
OBJECT-TYPE    
  Counter  

lportSmdsCntDstGaNotFounds 1.3.6.1.4.1.277.1.5.1.1.137
Number of instances that destination group address not found.
OBJECT-TYPE    
  Counter  

lportSmdsCntSrcIaScrnFails 1.3.6.1.4.1.277.1.5.1.1.138
Number of instances that source individual address screening failed.
OBJECT-TYPE    
  Counter  

lportSmdsCntDstIaScrnFails 1.3.6.1.4.1.277.1.5.1.1.139
Number of instances that destination individual address screening failed.
OBJECT-TYPE    
  Counter  

lportSmdsCntDstGaScrnFails 1.3.6.1.4.1.277.1.5.1.1.140
Number of instances that destination group address screening failed.
OBJECT-TYPE    
  Counter  

lportSmdsTotalDiscards 1.3.6.1.4.1.277.1.5.1.1.141
total number of discards.
OBJECT-TYPE    
  Counter  

lportSmdsSsiNode 1.3.6.1.4.1.277.1.5.1.1.142
The Node of the SSI which this DXI/SNI is multiplexed to.
OBJECT-TYPE    
  INTEGER  

lportBilling 1.3.6.1.4.1.277.1.5.1.1.143
This object defines the ability to enable and disable billing on this logical port (for SMDS this must be a DXI). When the value of nodeBilling is 'enabled', the value of this object will take precedence. When the value of nodeBilling is 'disabled', the value of this object will be overridden and billing will be disabled. The default value of this object is 'disabled'.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

lportSmdsReserved144 1.3.6.1.4.1.277.1.5.1.1.144
reserved! ignore!
OBJECT-TYPE    
  INTEGER  

lportLinkStatus 1.3.6.1.4.1.277.1.5.1.1.145
Link protocol status. The Link protocol may be frame relay LMI, DXI heart beat poll, PPP LCP, etc, depends on the lport type.
OBJECT-TYPE    
  INTEGER up(1), down(2)  

lportLMIDelay 1.3.6.1.4.1.277.1.5.1.1.146
The number of seconds 1-9 to buffer (or initiate) a FR LMI async update (or ATM OAM alarms) to allow filtering of LMI async events. Zero (0) indicates that no buffering is done (all updates are immediate) and 255 indicates that no updates are sent.
OBJECT-TYPE    
  INTEGER  

lportCRC 1.3.6.1.4.1.277.1.5.1.1.147
Lport CRC selection: 0 - 16 bit CRC 1 - 32 bit CRC
OBJECT-TYPE    
  INTEGER  

lportSmdsMulticastGa 1.3.6.1.4.1.277.1.5.1.1.148
The Multicast Group Address is the smds broadcast address which is used to get smds address from its IP address.
OBJECT-TYPE    
  OCTET STRING  

lportSmdsMulticastIpAddr 1.3.6.1.4.1.277.1.5.1.1.149
This IP address is this logical port's IP address.
OBJECT-TYPE    
  IpAddress  

lportAtmVPI 1.3.6.1.4.1.277.1.5.1.1.150
VPI value in the ATM cell header: ATM DXI with HSSI IOP VPI (4 lsb bit) range: 0 - 15 ATM UNI DS3/E3 IOP VPI (4 lsb bit) range: 0 - 15
OBJECT-TYPE    
  INTEGER  

lportAtmVCI 1.3.6.1.4.1.277.1.5.1.1.151
VCI value in the ATM cell header: ATM DXI with HSSI IOP VCI (6 lsb bit) range: 0 - 63 ATM UNI DS3/E3 IOP VCI (8 lsb bit) range: 0 - 255
OBJECT-TYPE    
  INTEGER  

lportPeakCellRateindex 1.3.6.1.4.1.277.1.5.1.1.152
Peak cell rate queue index
OBJECT-TYPE    
  INTEGER  

lportSustCellRate 1.3.6.1.4.1.277.1.5.1.1.153
Sustainable cell rate in cell/second
OBJECT-TYPE    
  INTEGER  

lportBurstTolerance 1.3.6.1.4.1.277.1.5.1.1.154
Burst Tolerance in multiple of 32 cells
OBJECT-TYPE    
  INTEGER  

lportBuTrkOnFailure 1.3.6.1.4.1.277.1.5.1.1.155
Enables or disables trunk backup due to link down.
OBJECT-TYPE    
  INTEGER enabled(1)  

lportTrkFailureThrsh 1.3.6.1.4.1.277.1.5.1.1.156
The number of seconds a primary trunk must remain down for trunk backup to be initiated.
OBJECT-TYPE    
  INTEGER  

lportTrkRestThrsh 1.3.6.1.4.1.277.1.5.1.1.157
The number of seconds a primary trunk must remain up for trunk backup to be terminated
OBJECT-TYPE    
  INTEGER  

lportBuTrkRetryInt 1.3.6.1.4.1.277.1.5.1.1.158
The number of seconds between backup trunk call setup retries.
OBJECT-TYPE    
  INTEGER  

lportBuTrkRetryNum 1.3.6.1.4.1.277.1.5.1.1.159
The number of backup trunk call setup tries per call setup cycle.
OBJECT-TYPE    
  INTEGER  

lportBuTrkCycleInt 1.3.6.1.4.1.277.1.5.1.1.160
The number of seconds between backup trunk call setup cycles.
OBJECT-TYPE    
  INTEGER  

lportTrkManualBu 1.3.6.1.4.1.277.1.5.1.1.161
Initiate or terminate manual backup for a primary trunk. none neither initiate or terminate initCmd initiate operator commanded backup termCmd terminate operator commanded backup initSched initiate scheduled backup termSched terminate scheduled backup
OBJECT-TYPE    
  INTEGER initCmd(1), termCmd(2), initSched(3), termSched(4)  

lportPrimTrk 1.3.6.1.4.1.277.1.5.1.1.162
Indicates the primary trunk lportIfIndex for which a backup trunk is serving as a backup. This value is also used to determine trunk type by the following convention: Value Trunk Type 0 Normal lportIfIndex of this trunk Primary other lportIfIndex Backup
OBJECT-TYPE    
  Index  

lportInitCallSetup 1.3.6.1.4.1.277.1.5.1.1.163
TRUE if node must initiate backup trunk call setup for this primary trunk. Otherwise FALSE.
OBJECT-TYPE    
  INTEGER true(1)  

lportBuFailReason 1.3.6.1.4.1.277.1.5.1.1.164
Indicates the reason for the failure to perform trunk backup.
OBJECT-TYPE    
  INTEGER buTrkNotDef(1), buTrkNotEstab(2)  

lportQ922Enable 1.3.6.1.4.1.277.1.5.1.1.165
Set 1 to eanble Q.922 on this port. Q.922 must be enabled if the port is used for SVC.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

lportQ922State 1.3.6.1.4.1.277.1.5.1.1.166
Q.922 state. This object only makes sense when Q.922 is enabled.
OBJECT-TYPE    
  INTEGER tei-unassigned(1), assign-awaiting(2), establish-awaiting(3), tei-assigned(4), awaiting-establishment(5), awaiting-release(6), multiple-frame-established(7), timer-recovery(8)  

lportTrkPduRevision 1.3.6.1.4.1.277.1.5.1.1.167
The Trunk PDU Revision number being used over this trunk.
OBJECT-TYPE    
  INTEGER  

lportPVCMgrPduRevision 1.3.6.1.4.1.277.1.5.1.1.168
The PVC Manager PDU Revision number being used over this trunk.
OBJECT-TYPE    
  INTEGER  

lportDS0LoopStatus 1.3.6.1.4.1.277.1.5.1.1.169
Indicates whether this logical port has one or more DS0's in loopback
OBJECT-TYPE    
  INTEGER  

lportISDNDuration 1.3.6.1.4.1.277.1.5.1.1.170
The number of seconds that the ISDN call has been established.
OBJECT-TYPE    
  INTEGER  

lportISDNSourceAddr 1.3.6.1.4.1.277.1.5.1.1.171
The E.164 address of the source of this ISDN connection.
OBJECT-TYPE    
  OCTET STRING  

lportISDNDestAddr 1.3.6.1.4.1.277.1.5.1.1.172
The E.164 address of the destination of this ISDN connection.
OBJECT-TYPE    
  OCTET STRING  

lportISDNIpAddr 1.3.6.1.4.1.277.1.5.1.1.173
The Ip Address of the client connected to this B-Channel
OBJECT-TYPE    
  IpAddress  

lportISDNCallRejCause 1.3.6.1.4.1.277.1.5.1.1.174
The cause of the call rejection - inability to authenticate or pool is busy.
OBJECT-TYPE    
  INTEGER  

lportLastInvalidDLCI 1.3.6.1.4.1.277.1.5.1.1.175
This item pertains to user frame relay lports only. The frame relay header of the received frame contains a dlci, which uniquely identifies a specific pvc on this lport. When no pvc has been configured, on the lport, that corresponds to the dlci specified in the frame header, the frame is said to have an invalid dlci. This lport entry holds the value of the most recent invalid dlci received on this lport, to be used in troubleshooting faulty configurations.
OBJECT-TYPE    
  INTEGER  

lportTrkProtState 1.3.6.1.4.1.277.1.5.1.1.176
The current operational state of the link trunk protocol on this link.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), none(3)  

lportTrkTrafficMix 1.3.6.1.4.1.277.1.5.1.1.177
The types of traffic allowed over a Cascade trunk.
OBJECT-TYPE    
  INTEGER normal(1), management-only(2), management-and-PVCs(3), private(4)  

lportNumVC 1.3.6.1.4.1.277.1.5.1.1.178
The number of VCs going to or through a particular port.
OBJECT-TYPE    
  INTEGER  

lportTrkAdminCost 1.3.6.1.4.1.277.1.5.1.1.179
The administrative cost of the trunk. Used when routing circuits. Trunks with lower costs are preferred. Value ranges from 1 to 65,535.
OBJECT-TYPE    
  INTEGER  

lportPrivateNet 1.3.6.1.4.1.277.1.5.1.1.180
If non-zero, indicates the private network that the lport belongs to. If 0, the lport is publicly shared.
OBJECT-TYPE    
  INTEGER  

lportTrkStaticDelay 1.3.6.1.4.1.277.1.5.1.1.181
The measured round-trip delay of the trunk, in milliseconds. Measured when the trunk last became operational.
OBJECT-TYPE    
  INTEGER  

lportTrkDynamicDelay 1.3.6.1.4.1.277.1.5.1.1.182
The recently measured round-tip delay of the trunk. May vary from lportTrkStaticDelay due to congestion, or reprovisioning of the underlying media.
OBJECT-TYPE    
  INTEGER  

lportAtmDataRateQoS1 1.3.6.1.4.1.277.1.5.1.1.183
An estimate of the logical port's data rate in bits per second reserved for QoS class 1.
OBJECT-TYPE    
  INTEGER  

lportAtmDataRateQoS2 1.3.6.1.4.1.277.1.5.1.1.184
An estimate of the logical port's data rate in bits per second reserved for QoS class 2.
OBJECT-TYPE    
  INTEGER  

lportAtmDataRateQoS3 1.3.6.1.4.1.277.1.5.1.1.185
An estimate of the logical port's data rate in bits per second reserved for QoS class 3.
OBJECT-TYPE    
  INTEGER  

lportAtmDataRateQoS4 1.3.6.1.4.1.277.1.5.1.1.186
An estimate of the logical port's data rate in bits per second reserved for QoS class 4.
OBJECT-TYPE    
  INTEGER  

lportOutVAvailbwQoS1 1.3.6.1.4.1.277.1.5.1.1.187
Current outgoing available virtual bandwidth reserved for QoS class 1.
OBJECT-TYPE    
  INTEGER  

lportOutVAvailbwQoS2 1.3.6.1.4.1.277.1.5.1.1.188
Current outgoing available virtual bandwidth reserved for QoS class 2.
OBJECT-TYPE    
  INTEGER  

lportOutVAvailbwQoS3 1.3.6.1.4.1.277.1.5.1.1.189
Current outgoing available virtual bandwidth reserved for QoS class 3.
OBJECT-TYPE    
  INTEGER  

lportOutVAvailbwQoS4 1.3.6.1.4.1.277.1.5.1.1.190
Current outgoing available virtual bandwidth reserved for QoS class 4.
OBJECT-TYPE    
  INTEGER  

lportInVAvailbwQoS1 1.3.6.1.4.1.277.1.5.1.1.191
Current incoming available virtual bandwidth reserved for QoS class 1.
OBJECT-TYPE    
  INTEGER  

lportInVAvailbwQoS2 1.3.6.1.4.1.277.1.5.1.1.192
Current incoming available virtual bandwidth reserved for QoS class 2.
OBJECT-TYPE    
  INTEGER  

lportInVAvailbwQoS3 1.3.6.1.4.1.277.1.5.1.1.193
Current incoming available virtual bandwidth reserved for QoS class 3.
OBJECT-TYPE    
  INTEGER  

lportInVAvailbwQoS4 1.3.6.1.4.1.277.1.5.1.1.194
Currently incoming available virtual bandwidth reserved for QoS class 4.
OBJECT-TYPE    
  INTEGER  

lportOutAllocbwQoS1 1.3.6.1.4.1.277.1.5.1.1.195
Current outgoing allocated bandwidth for QoS Class 1.
OBJECT-TYPE    
  INTEGER  

lportOutAllocbwQoS2 1.3.6.1.4.1.277.1.5.1.1.196
Current outgoing allocated bandwidth for QoS Class 2.
OBJECT-TYPE    
  INTEGER  

lportOutAllocbwQoS3 1.3.6.1.4.1.277.1.5.1.1.197
Current outgoing allocated bandwidth for QoS Class 3.
OBJECT-TYPE    
  INTEGER  

lportOutAllocbwQoS4 1.3.6.1.4.1.277.1.5.1.1.198
Current outgoing allocated bandwidth for QoS Class 4.
OBJECT-TYPE    
  INTEGER  

lportInAllocbwQoS1 1.3.6.1.4.1.277.1.5.1.1.199
Current incoming allocated bandwidth for QoS Class 1.
OBJECT-TYPE    
  INTEGER  

lportInAllocbwQoS2 1.3.6.1.4.1.277.1.5.1.1.200
Current incoming allocated bandwidth for QoS Class 2.
OBJECT-TYPE    
  INTEGER  

lportInAllocbwQoS3 1.3.6.1.4.1.277.1.5.1.1.201
Current incoming allocated bandwidth for QoS Class 3.
OBJECT-TYPE    
  INTEGER  

lportInAllocbwQoS4 1.3.6.1.4.1.277.1.5.1.1.202
Current incoming allocated bandwidth for QoS Class 4.
OBJECT-TYPE    
  INTEGER  

lportDynamicQoSbw 1.3.6.1.4.1.277.1.5.1.1.203
Bitmap defining which QoS Classes should have bandwidth allocated dynamically from lportDataRate instead of reserving a percentage up-front.
OBJECT-TYPE    
  INTEGER qos-class-1(1), qos-class-2(2), qos-class-3(4), qos-class-4(8)  

lportSVCRetryTimer 1.3.6.1.4.1.277.1.5.1.1.204
The duration in seconds (1..255) the network is allowed to re-establish a SVC after network failure before clearing the SVC. A value of (0) indicates continuous retries by the network until the user clears the SVC.
OBJECT-TYPE    
  INTEGER  

lportAtmNetworkType 1.3.6.1.4.1.277.1.5.1.1.205
Whether this lport is supporting a private or public network.
OBJECT-TYPE    
  INTEGER private(1), public(2)  

lportAtmRouteMetricQoS1 1.3.6.1.4.1.277.1.5.1.1.206
Routing metric associated with QoS Class 1.
OBJECT-TYPE    
  INTEGER administrative-cost(1), end-to-end-delay(2), cell-delay-variation(3)  

lportAtmRouteMetricQoS2 1.3.6.1.4.1.277.1.5.1.1.207
Routing metric associated with QoS Class 2.
OBJECT-TYPE    
  INTEGER administrative-cost(1), end-to-end-delay(2), cell-delay-variation(3)  

lportAtmRouteMetricQoS3 1.3.6.1.4.1.277.1.5.1.1.208
Routing metric associated with QoS Class 3.
OBJECT-TYPE    
  INTEGER administrative-cost(1), end-to-end-delay(2), cell-delay-variation(3)  

lportAtmRouteMetricQoS4 1.3.6.1.4.1.277.1.5.1.1.209
Routing metric associated with QoS Class 4.
OBJECT-TYPE    
  INTEGER administrative-cost(1), end-to-end-delay(2), cell-delay-variation(3)  

lportIlmiPollTimeout 1.3.6.1.4.1.277.1.5.1.1.210
The duration in seconds (1..255) the ILMI poll is generated by the network-side UME. A value of 0 set to default polling period of 5 seconds.
OBJECT-TYPE    
  INTEGER  

lportAtmProtocol 1.3.6.1.4.1.277.1.5.1.1.211
UNI protocol version for this port.
OBJECT-TYPE    
  INTEGER uni-30(1), uni-31(2), iisp(3)  

lportIlmiAdminStatus 1.3.6.1.4.1.277.1.5.1.1.212
Administrative state for ILMI function on this port.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

lportIlmiOperStatus 1.3.6.1.4.1.277.1.5.1.1.213
Operational status for ILMI function on this port.
OBJECT-TYPE    
  INTEGER down(1), registering(2), up(3)  

lportIlmiPollRetry 1.3.6.1.4.1.277.1.5.1.1.214
The number of retries of ILMI poll request will be generated when network-side UME detects loss of ILMI connectivity. A value of 0 sets to default value of 4 times
OBJECT-TYPE    
  Counter  

lportAtmVpiBits 1.3.6.1.4.1.277.1.5.1.1.215
Number of bits of VPI supported.
OBJECT-TYPE    
  INTEGER  

lportAtmVciBits 1.3.6.1.4.1.277.1.5.1.1.216
Number of bits of VCI supported.
OBJECT-TYPE    
  INTEGER  

lportAtmOamAlarmEnable 1.3.6.1.4.1.277.1.5.1.1.217
If disabled then OAM alarms are not generated for circuits that are down on this lport.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

lportInVAvailbw 1.3.6.1.4.1.277.1.5.1.1.218
Currently available Incoming virtual bandwidth.
OBJECT-TYPE    
  INTEGER  

lportbwUNIPolicy 1.3.6.1.4.1.277.1.5.1.1.219
The network policy towards requiring sufficient bandwidth at the UNI interface prior to allowing a circuit to be established.
OBJECT-TYPE    
  INTEGER enable-uni-bw-policing(1), disable-uni-bw-policing(2)  

lportStarvation 1.3.6.1.4.1.277.1.5.1.1.220
The CBR card detected a starvation condition on this lport for the extended period defined in Bellcore TA-NWT-001248
OBJECT-TYPE    
  INTEGER ok(1), error(2)  

lportRecOverflow 1.3.6.1.4.1.277.1.5.1.1.221
The CBR card detected a receive overflow condition on this lport for the extended period defined in Bellcore TA-NWT-001248
OBJECT-TYPE    
  INTEGER ok(1), error(2)  

lportLossOfCellSequence 1.3.6.1.4.1.277.1.5.1.1.222
The CBR card detected a LOS condition on this lport for the extended period defined in Bellcore TA-NWT-001248
OBJECT-TYPE    
  INTEGER ok(1), error(2)  

lportLossOfStructurePointer 1.3.6.1.4.1.277.1.5.1.1.223
The CBR card detected a loss of structure pointer condition on this lport for the extended period defined in Bellcore TA-NWT-001248
OBJECT-TYPE    
  INTEGER ok(1), error(2)  

lportCbrInsDummyCells 1.3.6.1.4.1.277.1.5.1.1.224
The number of dummy cells inserted due to cell loss on a constant bit rate (AAL1) interface.
OBJECT-TYPE    
  Counter  

lportRecFifoUnderflowCnt 1.3.6.1.4.1.277.1.5.1.1.225
The number of receive FIFO underflows since the last reset. If this condition persists, a lportCBRLineDataError trap is issued indicating the lportStarvation.
OBJECT-TYPE    
  Counter  

lportRecFifoOverflowCnt 1.3.6.1.4.1.277.1.5.1.1.226
The number of receive FIFO overflows since the last reset. If this condition persists, a lportCBRLineDataError trap is issued indicating the receive FIFO overflow.
OBJECT-TYPE    
  Counter  

lportCbrLossOfStructurePointerCnt 1.3.6.1.4.1.277.1.5.1.1.227
The object counts how often the structured CBR card detected a loss of the structure pointer since the last reset.
OBJECT-TYPE    
  Counter  

lportCbrLossOfCellSequenceCnt 1.3.6.1.4.1.277.1.5.1.1.228
The number of loss of cell sequence since the last reset.
OBJECT-TYPE    
  Counter  

lportShaperId 1.3.6.1.4.1.277.1.5.1.1.229
The shaper to be used for this ATM trunk interworking with frame relay: 1-port ATM-IWU STM-1/STS-3c card -------------------------------- Values: 1..16
OBJECT-TYPE    
  INTEGER  

lportIlmiPrefixScreenMode 1.3.6.1.4.1.277.1.5.1.1.230
The type of screening to apply against dynamic prefixes received from the peer ILMI entity at this DTE port.
OBJECT-TYPE    
  INTEGER node-prefix(1), port-prefix(2), node-prefix-or-port-prefix(3), reject-all(127), accept-all(255)  

lportSmdsPduViolTca 1.3.6.1.4.1.277.1.5.1.1.231
This object defines the ability to enable and disable SMDS pdu violation traps on this logical port. This functionality applies to the following logical port types: SMDS DXI/SNI DCE SMDS DXI/SNI DTE SMDS SSI DTE SMDS Optimum Trunk Direct Line Trunk The default value of this object is 'disabled'.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

lportSmdsPduViolThresh 1.3.6.1.4.1.277.1.5.1.1.232
This object defines the Smds pdu violation threshold for this logical port. The allowable range of threshold values is 1-255. The default value of this object is '10'.
OBJECT-TYPE    
  INTEGER  

lportSmdsPduHdrSip3SaNotFound 1.3.6.1.4.1.277.1.5.1.1.233
This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Sa Not Found. The first 8 bytes of the octet string (i.e.; 16 digits in BCD format) correspond to the destination address. The second 8 bytes correspond to the source address.
OBJECT-TYPE    
  OCTET STRING  

lportSmdsPduHdrSip3SaDaOnSamePort 1.3.6.1.4.1.277.1.5.1.1.234
This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Sa Da On Same Port. The first 8 bytes of the octet string (i.e.; 16 digits in BCD format) correspond to the destination address. The second 8 bytes correspond to the source address.
OBJECT-TYPE    
  OCTET STRING  

lportSmdsPduHdrSip3DstGaNotFound 1.3.6.1.4.1.277.1.5.1.1.235
This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Dst Ga Not Found. The first 8 bytes of the octet string (i.e.; 16 digits in BCD format) correspond to the destination address. The second 8 bytes correspond to the source address.
OBJECT-TYPE    
  OCTET STRING  

lportSmdsPduHdrSip3DstIaScrnFail 1.3.6.1.4.1.277.1.5.1.1.236
This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Dst Ia Scrn Fail. The first 8 bytes of the octet string (i.e.; 16 digits in BCD format) correspond to the destination address. The second 8 bytes correspond to the source address.
OBJECT-TYPE    
  OCTET STRING  

lportSmdsPduHdrSip3SaValFail 1.3.6.1.4.1.277.1.5.1.1.237
This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Sa Val Fail. The first 8 bytes of the octet string (i.e.; 16 digits in BCD format) correspond to the destination address. The second 8 bytes correspond to the source address.
OBJECT-TYPE    
  OCTET STRING  

lportSmdsPduHdrSip3DstIaNotFound 1.3.6.1.4.1.277.1.5.1.1.238
This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Dst Ia Not Found. The first 8 bytes of the octet string (i.e.; 16 digits in BCD format) correspond to the destination address. The second 8 bytes correspond to the source address.
OBJECT-TYPE    
  OCTET STRING  

lportSmdsPduHdrSip3SrcIaScrnFail 1.3.6.1.4.1.277.1.5.1.1.239
This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Src Ia Scrn Fail. The first 8 bytes of the octet string (i.e.; 16 digits in BCD format) correspond to the destination address. The second 8 bytes correspond to the source address.
OBJECT-TYPE    
  OCTET STRING  

lportSmdsPduHdrSip3DstGaScrnFail 1.3.6.1.4.1.277.1.5.1.1.240
This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Dst Ga Scrn Fail. The first 8 bytes of the octet string (i.e.; 16 digits in BCD format) correspond to the destination address. The second 8 bytes correspond to the source address.
OBJECT-TYPE    
  OCTET STRING  

lportSmdsPduHdrSip3SaTypeInvalid 1.3.6.1.4.1.277.1.5.1.1.241
This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Sa Type Invalid. The first 8 bytes of the octet string (i.e.; 16 digits in BCD format) correspond to the destination address. The second 8 bytes correspond to the source address.
OBJECT-TYPE    
  OCTET STRING  

lportSmdsPduHdrSip3DaTypeInvalid 1.3.6.1.4.1.277.1.5.1.1.242
This object provides the Smds destination address and Smds source address of the last Smds pdu to cause the violation Smds Da Type Invalid. The first 8 bytes of the octet string (i.e.; 16 digits in BCD format) correspond to the destination address. The second 8 bytes correspond to the source address.
OBJECT-TYPE    
  OCTET STRING  

lportSmdsPduHdrDxi2LinkIdInvalid 1.3.6.1.4.1.277.1.5.1.1.243
This object provides the dxi2 header of the last Smds pdu to cause the violation Dxi2 Link Id Invalid. The length of this object is 4 bytes.
OBJECT-TYPE    
  OCTET STRING  

lportSmdsPduHdrDxi2CrInvalid 1.3.6.1.4.1.277.1.5.1.1.244
This object provides the dxi2 header of the last Smds pdu to cause the violation Dxi2 Cr Invalid. The length of this object is 4 bytes.
OBJECT-TYPE    
  OCTET STRING  

lportSmdsPduHdrDxi2CtrlInvalid 1.3.6.1.4.1.277.1.5.1.1.245
This object provides the dxi2 header of the last Smds pdu to cause the violation Dxi2 Ctrl Invalid. The length of this object is 4 bytes.
OBJECT-TYPE    
  OCTET STRING  

lportSmdsPduHdrDxi2StationIdInvalid 1.3.6.1.4.1.277.1.5.1.1.246
This object provides the dxi2 header of the last Smds pdu to cause the violation Dxi2 Station Id Invalid. The length of this object is 4 bytes.
OBJECT-TYPE    
  OCTET STRING  

lportSmdsPduHdrDxi2AeInvalid 1.3.6.1.4.1.277.1.5.1.1.247
This object provides the dxi2 header of the last Smds pdu to cause the violation Dxi2 Ae Invalid. The length of this object is 4 bytes.
OBJECT-TYPE    
  OCTET STRING  

lportDS0FarendLpbkEnabled 1.3.6.1.4.1.277.1.5.1.1.248
Set a single DS0 into farend loopback 1-24.
OBJECT-TYPE    
  INTEGER  

lportDS0FarendLpbkDisabled 1.3.6.1.4.1.277.1.5.1.1.249
Set a single DS0 out farend loopback 1-24.
OBJECT-TYPE    
  INTEGER  

lportTrkProtFailureThreshold 1.3.6.1.4.1.277.1.5.1.1.250
The time, measured in seconds, that Trunk Protocol waits before transitioning the state of an unresponsive trunk from UP to DOWN. Trunk protocol keepalive requests are issued on the trunk lport once per second. This value defines the failure threshold, that is, the number of consecutive requests that must go unanswered before the Trunk Protocol application will declare the trunk lport DOWN.
OBJECT-TYPE    
  INTEGER  

lportPtr 1.3.6.1.4.1.277.1.5.1.1.251
An octet string indicating the lport pointer.
OBJECT-TYPE    
  OCTET STRING  

lportISDNPoolUtil 1.3.6.1.4.1.277.1.5.1.1.252
The percent utilization of the B-channel pool that this b-channel belongs to.
OBJECT-TYPE    
  INTEGER  

lportISDNIpAddrAssignFail 1.3.6.1.4.1.277.1.5.1.1.253
The cause value for why Ip Address assignment has failed.
OBJECT-TYPE    
  INTEGER  

lportTrkUtilQoS1 1.3.6.1.4.1.277.1.5.1.1.254
An estimate of the real QoS1 utilization of the trunk bandwidth in terms of a percentage of the configured trunk bandwidth.
OBJECT-TYPE    
  INTEGER  

lportTrkUtilQoS2 1.3.6.1.4.1.277.1.5.1.1.255
An estimate of the real QoS2 utilization of the trunk bandwidth in terms of a percentage of the configured trunk bandwidth.
OBJECT-TYPE    
  INTEGER  

lportTrkUtilQoS3 1.3.6.1.4.1.277.1.5.1.1.256
An estimate of the real QoS3 utilization of the trunk bandwidth in terms of a percentage of the configured trunk bandwidth.
OBJECT-TYPE    
  INTEGER  

lportTrkUtilQoS4 1.3.6.1.4.1.277.1.5.1.1.257
An estimate of the real QoS4 utilization of the trunk bandwidth in terms of a percentage of the configured trunk bandwidth.
OBJECT-TYPE    
  INTEGER  

lportInCells 1.3.6.1.4.1.277.1.5.1.1.267
The total number of cells received
OBJECT-TYPE    
  Counter  

lportOutCells 1.3.6.1.4.1.277.1.5.1.1.268
The total number of cells transmitted
OBJECT-TYPE    
  Counter  

ckt 1.3.6.1.4.1.277.1.6
OBJECT IDENTIFIER    

nodeFanStatusChange 1.3.6.1.4.1.277.1.6
This trap indicates that a fan has changed state (toggled between up and down states).
TRAP-TYPE    
  nodeFanIndex  
  nodeFanStatus  

cktTable 1.3.6.1.4.1.277.1.6.1
A table containing information about specific DLCIs, channels and corresponding circuits.
OBJECT-TYPE    
  SEQUENCE OF  
    CktEntry

cktEntry 1.3.6.1.4.1.277.1.6.1.1
The information regarding a single Data Link Connection Identifier.
OBJECT-TYPE    
  CktEntry  

cktSrcIfIndex 1.3.6.1.4.1.277.1.6.1.1.1
The ifIndex value of the corresponding ifEntry.
OBJECT-TYPE    
  Index  

cktSrcDlci 1.3.6.1.4.1.277.1.6.1.1.2
The DLCI used as the key for the circuit. For local DLCI significance, this is the local DLCI. For Global DLCI significance, this is the remote DLCI.
OBJECT-TYPE    
  INTEGER  

cktPriority 1.3.6.1.4.1.277.1.6.1.1.3
The priority level (1 through 3) for this circuit.
OBJECT-TYPE    
  INTEGER  

cktCir 1.3.6.1.4.1.277.1.6.1.1.4
The average number of user data (bits) that the network agrees to transfer over the circuit in one direction, measured over the measurement interval T = cktBc/cktCir.
OBJECT-TYPE    
  INTEGER  

cktBc 1.3.6.1.4.1.277.1.6.1.1.5
The maximum amount of data (bits) that the network agrees to transfer over the circuit under normal conditions, during the measurement interval.
OBJECT-TYPE    
  INTEGER  

cktBe 1.3.6.1.4.1.277.1.6.1.1.6
The maximum amount of uncommitted data (bits) that the network will attempt to transfer over the circuit during the measurement interval. By default, if not configured when creating the entry, the Excess Information Burst Size is set to the value of ifSpeed.
OBJECT-TYPE    
  INTEGER  

cktDestNodeId 1.3.6.1.4.1.277.1.6.1.1.7
The destination node ID for this circuit.
OBJECT-TYPE    
  INTEGER  

cktDestIfIndex 1.3.6.1.4.1.277.1.6.1.1.8
The interface identifier at the destination node for this circuit.
OBJECT-TYPE    
  INTEGER  

cktDestDlci 1.3.6.1.4.1.277.1.6.1.1.9
The DLCI which is the destination of the key DLCI. For local DLCI significance, this is the remote DLCI since the key DLCI is the local DLCI. For global significance, this is the local DLCI since the key DLCI is the remote DLCI.
OBJECT-TYPE    
  INTEGER  

cktTos 1.3.6.1.4.1.277.1.6.1.1.10
The type of service for the circuit. Only committed is supported in the FCS.
OBJECT-TYPE    
  INTEGER committed(1), shared(2)  

cktOde 1.3.6.1.4.1.277.1.6.1.1.11
This variable states whether graceful discard is enabled for the ckt.
OBJECT-TYPE    
  INTEGER on(1)  

cktAdminStatus 1.3.6.1.4.1.277.1.6.1.1.12
The desired state of the ckt.
OBJECT-TYPE    
  INTEGER down(1), up(2)  

cktCreationTime 1.3.6.1.4.1.277.1.6.1.1.13
The value of sysUpTime when the circuit was created (activated).
OBJECT-TYPE    
  TimeTicks  

cktLastTimeChange 1.3.6.1.4.1.277.1.6.1.1.14
The sysUpTime value when the circuit was last changed to the current state.
OBJECT-TYPE    
  TimeTicks  

cktVcState 1.3.6.1.4.1.277.1.6.1.1.15
The current state of the PVC segment in the Cascade network.
OBJECT-TYPE    
  INTEGER inactive(1), retry(2), calling(3), wcbdeact(4), wcbdelete(5), active(6), svcall(7), svclr(8), backedup(9), wcbbkdp(10), wcbreact(11), slowretry(12)  

cktDceState 1.3.6.1.4.1.277.1.6.1.1.16
The DCE state of the circuit.
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

cktDteStatus 1.3.6.1.4.1.277.1.6.1.1.17
The DTE status of the circuit.
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

cktRnr 1.3.6.1.4.1.277.1.6.1.1.18
The receiver's readiness for accepting data flow.
OBJECT-TYPE    
  INTEGER recvnotready(1)  

cktNiDown 1.3.6.1.4.1.277.1.6.1.1.19
The state of the network interface.
OBJECT-TYPE    
  INTEGER nidown(1)  

cktDteState 1.3.6.1.4.1.277.1.6.1.1.20
The DTE state of the circuit.
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

cktOperStatus 1.3.6.1.4.1.277.1.6.1.1.21
The current operational status of the entire PVC.
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

cktOutForward 1.3.6.1.4.1.277.1.6.1.1.22
If the value is 1, it means the outbound flow is on.
OBJECT-TYPE    
  INTEGER on(1)  

cktRerouteCnt 1.3.6.1.4.1.277.1.6.1.1.23
The reroute count.
OBJECT-TYPE    
  INTEGER  

cktVcPtr 1.3.6.1.4.1.277.1.6.1.1.24
An 8-byte Octect string indicating the vc pointer.
OBJECT-TYPE    
  OCTET STRING  

cktHopCnt 1.3.6.1.4.1.277.1.6.1.1.25
The count of hops along the circuit path. (Max is 16)
OBJECT-TYPE    
  INTEGER  

cktPath 1.3.6.1.4.1.277.1.6.1.1.26
The circuit path consisting a sequence of outbound interface indexes at nodes along the established circuit. The format is interface:interface:interface......
OBJECT-TYPE    
  OCTET STRING  

cktFailReason 1.3.6.1.4.1.277.1.6.1.1.27
The reason for the PVC establishment failure.
OBJECT-TYPE    
  INTEGER admindown(1), novcbuff(2), nobw(3), noroute(4), timeout(5), nopdubuff(6), nodest(7), trkrnr(8), trkdown(9), balancereroute(10), dead(11), defpathreroute(12), nidown(13), otherpvcsegdown(14), otherpvcsegrnr(15), usingaltpathwarning(16), iopdown(17), numsgbuffer(18), noport(19), misconfig(20), svcsetupfail(21), srcbackedup(22), srcunknown(23), dstunknown(24), bkpdlcicollision(25), oldrevinpath(26), smdsmgmttrunk(27), nevercalled(28), bothendptbackup(29), pvcroutemgttrunk(30), nomultipointparent(31), pvcroutefail(32), novpivci(33)  

cktFailNode 1.3.6.1.4.1.277.1.6.1.1.28
The node which causes the PVC failure.
OBJECT-TYPE    
  INTEGER  

cktFailPort 1.3.6.1.4.1.277.1.6.1.1.29
The port on the fail node which causes the PVC failure.
OBJECT-TYPE    
  INTEGER  

cktMcastGroupId 1.3.6.1.4.1.277.1.6.1.1.30
Multicast group identifier (1..32). This field is 0 for unicast PVCs.
OBJECT-TYPE    
  INTEGER  

cktMcastMemberList 1.3.6.1.4.1.277.1.6.1.1.31
A list of operations and the affected unicast DLCIs (lportId, cktId)s in a multicast group. The syntax is as follows: [op:dlci,dlci,...,op:dlci,dlci,...] where op can either be delete (0) or add (1)
OBJECT-TYPE    
  OCTET STRING  

cktMcastParentGroups 1.3.6.1.4.1.277.1.6.1.1.32
An 8-byte Octect string indicating the parent groups this DLCI belongs to.
OBJECT-TYPE    
  OCTET STRING  

cktInFrames 1.3.6.1.4.1.277.1.6.1.1.33
The number of inbound frames since the last reset.
OBJECT-TYPE    
  Counter  

cktInDEFrames 1.3.6.1.4.1.277.1.6.1.1.34
The number of inbound DE-marked frames since the last reset.
OBJECT-TYPE    
  Counter  

cktInODEFrames 1.3.6.1.4.1.277.1.6.1.1.35
The number of inbound ODE-marked frames since the last reset.
OBJECT-TYPE    
  Counter  

cktInFECNFrames 1.3.6.1.4.1.277.1.6.1.1.36
The number of inbound frames indicating forward congestion since the last reset.
OBJECT-TYPE    
  Counter  

cktInBECNFrames 1.3.6.1.4.1.277.1.6.1.1.37
The number of inbound frames indicating backward congestion since the last reset.
OBJECT-TYPE    
  Counter  

cktInDiscards 1.3.6.1.4.1.277.1.6.1.1.38
Number of inbound frames discarded by rate enforcement.
OBJECT-TYPE    
  Counter  

cktInOctets 1.3.6.1.4.1.277.1.6.1.1.39
The number of inbound octets since the last reset.
OBJECT-TYPE    
  Counter  

cktInDEOctets 1.3.6.1.4.1.277.1.6.1.1.40
The number of inbound DE-marked octets since the last reset.
OBJECT-TYPE    
  Counter  

cktInODEOctets 1.3.6.1.4.1.277.1.6.1.1.41
The number of inbound ODE-marked octets since the last reset.
OBJECT-TYPE    
  Counter  

cktOutFrames 1.3.6.1.4.1.277.1.6.1.1.42
The number of outbound frames since the last reset.
OBJECT-TYPE    
  Counter  

cktOutDEFrames 1.3.6.1.4.1.277.1.6.1.1.43
The number of outbound DE-marked frames since the last reset.
OBJECT-TYPE    
  Counter  

cktOutODEFrames 1.3.6.1.4.1.277.1.6.1.1.44
The number of outbound ODE-marked frames since the last reset.
OBJECT-TYPE    
  Counter  

cktOutFECNFrames 1.3.6.1.4.1.277.1.6.1.1.45
The number of outbound FECN-marked frames since the last reset.
OBJECT-TYPE    
  Counter  

cktOutBECNFrames 1.3.6.1.4.1.277.1.6.1.1.46
The number of outbound BECN-marked frames since the last reset.
OBJECT-TYPE    
  Counter  

cktOutOctets 1.3.6.1.4.1.277.1.6.1.1.47
The number of outbound octets since the last reset.
OBJECT-TYPE    
  Counter  

cktOutDEOctets 1.3.6.1.4.1.277.1.6.1.1.48
The number of outbound DE-marked octets since the last reset.
OBJECT-TYPE    
  Counter  

cktOutODEOctets 1.3.6.1.4.1.277.1.6.1.1.49
The number of outbound ODE-marked octets since the last reset.
OBJECT-TYPE    
  Counter  

cktOutLostFrames 1.3.6.1.4.1.277.1.6.1.1.50
The number of outbound frames that have been lost since the last reset.
OBJECT-TYPE    
  Counter  

cktOutLostDEFrames 1.3.6.1.4.1.277.1.6.1.1.51
The number of outbound DE-marked frames that have been lost since the last reset.
OBJECT-TYPE    
  Counter  

cktOutLostODEFrames 1.3.6.1.4.1.277.1.6.1.1.52
The number of outbound ODE-marked frames that have been lost since the last reset.
OBJECT-TYPE    
  Counter  

cktOutLostOctets 1.3.6.1.4.1.277.1.6.1.1.53
The number of outbound octets that have been lost since the last reset.
OBJECT-TYPE    
  Counter  

cktOutLostDEOctets 1.3.6.1.4.1.277.1.6.1.1.54
The number of outbound DE-marked octets that have been lost since the last reset.
OBJECT-TYPE    
  Counter  

cktOutLostODEOctets 1.3.6.1.4.1.277.1.6.1.1.55
The number of outbound ODE-marked octets that have been lost since the last reset.
OBJECT-TYPE    
  Counter  

cktRtMinDelay 1.3.6.1.4.1.277.1.6.1.1.56
The minimum round-trip delay (micro-seconds).
OBJECT-TYPE    
  INTEGER  

cktRtMaxDelay 1.3.6.1.4.1.277.1.6.1.1.57
The maximum round-trip delay (micro-seconds).
OBJECT-TYPE    
  INTEGER  

cktRtAvgDelay 1.3.6.1.4.1.277.1.6.1.1.58
The average round-trip delay (micro-seconds).
OBJECT-TYPE    
  INTEGER  

cktDiagTestId 1.3.6.1.4.1.277.1.6.1.1.59
Identification for the diagnostics tests to be run.
OBJECT-TYPE    
  INTEGER  

cktDiagTestRuns 1.3.6.1.4.1.277.1.6.1.1.60
Number of passes of the diagnostics tests to be run. The default value is 1.
OBJECT-TYPE    
  INTEGER  

cktHelloCounter 1.3.6.1.4.1.277.1.6.1.1.61
Number of PVC hello pdu frames received in the VC entry of the called side.
OBJECT-TYPE    
  INTEGER  

cktHelloAckCounter 1.3.6.1.4.1.277.1.6.1.1.62
Number of PVC hello Ack pdu frames received in the VC entry of the calling side.
OBJECT-TYPE    
  INTEGER  

cktDefinedPath 1.3.6.1.4.1.277.1.6.1.1.63
User defined path. in the format of Nx,x,x,Nx,.... If x is not prefixed with 'N', x is an interface ID. If x is prefixed with `N`, x is a node ID.
OBJECT-TYPE    
  OCTET STRING  

cktDefinedPathCount 1.3.6.1.4.1.277.1.6.1.1.64
User defined path hop count.
OBJECT-TYPE    
  INTEGER  

cktDefinedPathEnable 1.3.6.1.4.1.277.1.6.1.1.65
If set to 1, it means there is an user defined path for this circuit and it is enabled.
OBJECT-TYPE    
  INTEGER  

cktDefinedPathAltOption 1.3.6.1.4.1.277.1.6.1.1.66
If set to 1, it means that if the user defined path fails, use the ospf-determined path.
OBJECT-TYPE    
  INTEGER  

cktUsingDefinedPath 1.3.6.1.4.1.277.1.6.1.1.67
If set to 1, it indicates the PVC is currently using the defined path.
OBJECT-TYPE    
  INTEGER  

cktTryAltPath 1.3.6.1.4.1.277.1.6.1.1.68
If set to 1, it means the inactive PVC will be activated on the ospf-determined path in the next retry.
OBJECT-TYPE    
  INTEGER  

cktNotVirgin 1.3.6.1.4.1.277.1.6.1.1.69
If set to 1, it means this VC entry has been successfuly activated before.
OBJECT-TYPE    
  INTEGER  

cktInForward 1.3.6.1.4.1.277.1.6.1.1.70
If the value is 1, it means the inbound flow is OK.
OBJECT-TYPE    
  INTEGER  

cktBtusSeg 1.3.6.1.4.1.277.1.6.1.1.71
Number of Bus xmit units per data segment
OBJECT-TYPE    
  INTEGER  

cktInSegmentsDiscards 1.3.6.1.4.1.277.1.6.1.1.72
Number of segments received that were discarded because of frame reassembly errors.
OBJECT-TYPE    
  Counter  

cktAtmVPI 1.3.6.1.4.1.277.1.6.1.1.73
VPI value in the ATM cell header: ATM DXI with HSSI IOP VPI (4 lsb bit) range: 0 - 15 ATM UNI DS3/E3 IOP VPI (4 lsb bit) range: 0 - 15 T1 ATM 4 lsb range 0-15 ATM-IWU STM-1/STS-3c VPI (<=12 lsb bit) range: 0-4095
OBJECT-TYPE    
  INTEGER  

cktAtmVCI 1.3.6.1.4.1.277.1.6.1.1.74
VCI value in the ATM cell header: ATM DXI with HSSI IOP VCI (6 lsb bit) range: 0 - 63 ATM UNI DS3/E3 IOP VCI (8 lsb bit) range: 0 - 255 T1 ATM 4 lsb VCI (6 lsb bit) range 0 - 255 ATM-IWU STM-1/STS-3c VCI (<=12 lsb bit) range: 0-4095
OBJECT-TYPE    
  INTEGER  

cktType 1.3.6.1.4.1.277.1.6.1.1.75
1 if a permanent virtual circuit; 2 if a switched virtual circuit.
OBJECT-TYPE    
  INTEGER pvc(1), svc(2)  

cktSvcCallingParty 1.3.6.1.4.1.277.1.6.1.1.76
The calling party number if this is a switched virtual circuit.
OBJECT-TYPE    
  OCTET STRING  

cktSvcCalledParty 1.3.6.1.4.1.277.1.6.1.1.77
The called party number if this is a switched virtual circuit.
OBJECT-TYPE    
  OCTET STRING  

cktSvcDuration 1.3.6.1.4.1.277.1.6.1.1.78
The duration since the SVC circuit has been running.
OBJECT-TYPE    
  TimeTicks  

cktSvcCause 1.3.6.1.4.1.277.1.6.1.1.79
SVC cause number. The index will be 0.0 and should be disregarded. The following cause numbers maybe returned by stdx: 1 - unassigned number, callee is not assigned 2 - no route to specified transit network 3 - no route to destination 6 - channel unacceptable 16 - normal clearing 17 - user busy 18 - no user responding 21 - call rejected by whoever is sending this cause 22 - number changed, called party has changed its number 27 - destination out of order (the interface to called user) 28 - called party number is invalid 29 - facility requested can't be provided by network 30 - included in STATUS message to indicate it is responding to a STATUS ENQUIRY 31 - unspecified, used if no other cause is appropriate 34 - no circuit or channel available to handle the call 38 - network is out of order 41 - tempprary failure, i.e., caller may try again 42 - network congestion 43 - access information (user-to-user) discarded 44 - requested circuit unavailable 58 - bearer capability not available 63 - requested service unavailable 65 - requested bearer capability is not implemented 81 - call reference is unknown 95 - invalid message 96 - mandatory information element is missing 97 - message type is unknown 98 - message not compatible with call state 99 - information element is unknown or not implemented 100 - invalid information element contents 101 - message not compatible with call state
OBJECT-TYPE    
  INTEGER  

cktXlatFlag 1.3.6.1.4.1.277.1.6.1.1.80
0 if RFC1490 or no translation; 1 if RFC1483 translation.
OBJECT-TYPE    
  INTEGER rfc1483(1)  

cktDestLaddr 1.3.6.1.4.1.277.1.6.1.1.81
The destination logical address of the circuit.
OBJECT-TYPE    
  INTEGER  

cktSrcLaddr 1.3.6.1.4.1.277.1.6.1.1.82
The source logical address of the circuit.
OBJECT-TYPE    
  INTEGER  

cktLoop 1.3.6.1.4.1.277.1.6.1.1.83
Setting this variable controls the loopback status of the given circuit endpoint.
OBJECT-TYPE    
  INTEGER local(1), remote(2), both(3)  

cktRerouteBalance 1.3.6.1.4.1.277.1.6.1.1.84
Setting this variable controls the use of rerouting to balance link usage.
OBJECT-TYPE    
  INTEGER disabled(1)  

cktCallingBackup 1.3.6.1.4.1.277.1.6.1.1.85
Indicates if a caller endpoint is calling a backup PVC.
OBJECT-TYPE    
  INTEGER true(1)  

cktRCir 1.3.6.1.4.1.277.1.6.1.1.86
The average number of user data (bits) that the network agrees to transfer over the circuit in the opposite direction, measured over the measurement interval T = cktBc/cktCir.
OBJECT-TYPE    
  INTEGER  

cktAtmQoS 1.3.6.1.4.1.277.1.6.1.1.87
The Quality of Service of the ATM Circuit. Valid only for ATM type circuits.
OBJECT-TYPE    
  INTEGER cbr(1), vbr1(2), vbr2(3), vbr3(4)  

cktAtmInCells 1.3.6.1.4.1.277.1.6.1.1.88
The Number of ATM cells received on a VC (VPC or VCC).
OBJECT-TYPE    
  Counter  

cktAtmOutCells 1.3.6.1.4.1.277.1.6.1.1.89
The Number of ATM cells transmitted on a VC (VPC or VCC)..
OBJECT-TYPE    
  Counter  

cktAtmInDiscardedClp0Cells 1.3.6.1.4.1.277.1.6.1.1.90
The Number of ATM CLP0 cells received and discarded on a VC (VPC or VCC)..
OBJECT-TYPE    
  Counter  

cktAtmInDiscardedClp1Cells 1.3.6.1.4.1.277.1.6.1.1.91
The Number of ATM CLP1 cells received and discarded on a VC (VPC or VCC).
OBJECT-TYPE    
  Counter  

cktAtmVcType 1.3.6.1.4.1.277.1.6.1.1.92
Type of ATM connection (VPC or VCC).
OBJECT-TYPE    
  INTEGER vpc(1), vcc(2)  

cktAtmPCR 1.3.6.1.4.1.277.1.6.1.1.93
The Peak Cell Rate measured in cells/second at which cells are transmitted for this circuit.
OBJECT-TYPE    
  INTEGER  

cktAtmSCR 1.3.6.1.4.1.277.1.6.1.1.94
The Sustainable Cell Rate is the average transmission rate in cells per second for this circuit. It must be less than or or equal to the Peak Cell Rate.
OBJECT-TYPE    
  INTEGER  

cktAtmMBS 1.3.6.1.4.1.277.1.6.1.1.95
The Maximum Burst size determines the maximum number of cells that can be transmitted at the peak cell rate.
OBJECT-TYPE    
  INTEGER  

cktAtmInPassedClp0Cells 1.3.6.1.4.1.277.1.6.1.1.96
The Number of ATM CLP 0 cells received and passed UPC on a VC (VPC or VCC).
OBJECT-TYPE    
  Counter  

cktAtmInPassedClp1Cells 1.3.6.1.4.1.277.1.6.1.1.97
The Number of ATM CLP 1 cells received and passed UPC on a VC (VPC or VCC).
OBJECT-TYPE    
  Counter  

cktAtmInTaggedCells 1.3.6.1.4.1.277.1.6.1.1.98
The Number of ATM cells received and tagged on a VC (VPC or VCC).
OBJECT-TYPE    
  Counter  

cktAtmOutClp0Cells 1.3.6.1.4.1.277.1.6.1.1.99
The Number of ATM CLP 0 cells transmitted on a VC (VPC or VCC)..
OBJECT-TYPE    
  Counter  

cktAtmOutClp1Cells 1.3.6.1.4.1.277.1.6.1.1.100
The Number of ATM CLP 1 cells transmitted on a VC (VPC or VCC)..
OBJECT-TYPE    
  Counter  

cktAtmRQoS 1.3.6.1.4.1.277.1.6.1.1.101
The Quality of Service of the ATM connection in the opposite direction.
OBJECT-TYPE    
  INTEGER cbr(1), vbr1(2), vbr2(3), vbr3(4)  

cktAtmTfdType 1.3.6.1.4.1.277.1.6.1.1.102
The combination of traffic parameters.
OBJECT-TYPE    
  INTEGER pcr-0-01(1), pcr-0-01-tag(2), pcr-01-scr-0-mbs-0(3), pcr-01-scr-0-mbs-0-tag(4), pcr-01(5), pcr-01-scr-01-mbs-01(6), pcr-01-bestEffort(7)  

cktAtmRTfdType 1.3.6.1.4.1.277.1.6.1.1.103
The combination of traffic parameters in opposite direction.
OBJECT-TYPE    
  INTEGER pcr-0-01(1), pcr-0-01-tag(2), pcr-01-scr-0-mbs-0(3), pcr-01-scr-0-mbs-0-tag(4), pcr-01(5), pcr-01-scr-01-mbs-01(6), pcr-01-bestEffort(7)  

cktAtmTfdParam1 1.3.6.1.4.1.277.1.6.1.1.104
The traffic descriptor parameter 1.
OBJECT-TYPE    
  INTEGER  

cktAtmTfdParam2 1.3.6.1.4.1.277.1.6.1.1.105
The traffic descriptor parameter 2.
OBJECT-TYPE    
  INTEGER  

cktAtmTfdParam3 1.3.6.1.4.1.277.1.6.1.1.106
The traffic descriptor parameter 3.
OBJECT-TYPE    
  INTEGER  

cktAtmRTfdParam1 1.3.6.1.4.1.277.1.6.1.1.107
The traffic descriptor parameter 1 for opposite direction.
OBJECT-TYPE    
  INTEGER  

cktAtmRTfdParam2 1.3.6.1.4.1.277.1.6.1.1.108
The traffic descriptor parameter 3 for opposite direction.
OBJECT-TYPE    
  INTEGER  

cktAtmRTfdParam3 1.3.6.1.4.1.277.1.6.1.1.109
The traffic descriptor parameter 3 for opposite direction.
OBJECT-TYPE    
  INTEGER  

cktAtmFrameIWF 1.3.6.1.4.1.277.1.6.1.1.110
Frame Relay/ATM Interworking Function indicator.
OBJECT-TYPE    
  INTEGER default(1), iwf(2)  

cktAtmUserPlane 1.3.6.1.4.1.277.1.6.1.1.111
Bitmap defining user plane capabilities.
OBJECT-TYPE    
  INTEGER point-to-point(1), point-to-multipoint(2)  

cktRBc 1.3.6.1.4.1.277.1.6.1.1.112
The maximum amount of data (bits) that the network agrees to transfer over the circuit in the opposite direction under normal conditions, during the measurement interval.
OBJECT-TYPE    
  INTEGER  

cktRBe 1.3.6.1.4.1.277.1.6.1.1.113
The maximum amount of uncommitted data (bits) that the network will attempt to transfer over the circuit in the opposite direction during the measurement interval. By default, if not configured when creating the entry, the Excess Information Burst Size is set to the value of ifSpeed.
OBJECT-TYPE    
  INTEGER  

cktOamLoopbackDirection 1.3.6.1.4.1.277.1.6.1.1.114
Which direction to send the loopback cell. If 'local', send out this circuit entry's port. If 'remote', send out the remote circuit entry's port.
OBJECT-TYPE    
  INTEGER local(1), remote(2)  

cktOamLoopbackType 1.3.6.1.4.1.277.1.6.1.1.115
Type of oam loopback to send - either segment or end to end.
OBJECT-TYPE    
  INTEGER segment(1), end-to-end(2)  

cktOamLoopbackHops 1.3.6.1.4.1.277.1.6.1.1.116
Number of hops the loopback cell should traverse inside the Cascade network before being echoed back by the far Cascade device.
OBJECT-TYPE    
  INTEGER  

cktOamLoopbackCount 1.3.6.1.4.1.277.1.6.1.1.117
Number of oam loopback cells left to send this session. Setting this from zero to non-zero starts the loopback session.
OBJECT-TYPE    
  INTEGER  

cktOamLoopbackReceived 1.3.6.1.4.1.277.1.6.1.1.118
Number of oam responses received for this loopback session.
OBJECT-TYPE    
  Counter  

cktOamLoopbackTimeouts 1.3.6.1.4.1.277.1.6.1.1.119
Number of times a loopback response was not received within the timeout period during this loopback session.
OBJECT-TYPE    
  Counter  

cktOamLoopbackReceivedHigh 1.3.6.1.4.1.277.1.6.1.1.120
Highest response time (in milliseconds) of an oam loopback response this loopback session.
OBJECT-TYPE    
  INTEGER  

cktOamLoopbackReceivedLow 1.3.6.1.4.1.277.1.6.1.1.121
Lowest response time (in milliseconds) of an oam loopback response this loopback session.
OBJECT-TYPE    
  INTEGER  

cktOamLoopbackReceivedAvg 1.3.6.1.4.1.277.1.6.1.1.122
Average response time (in milliseconds) of an oam loopback response this loopback session.
OBJECT-TYPE    
  INTEGER  

cktOamAlarmDisable 1.3.6.1.4.1.277.1.6.1.1.123
If disabled, then don't generate oam alarms if this circuit is down.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

cktShaperId 1.3.6.1.4.1.277.1.6.1.1.124
The shaper to be used for this virtual connection interworking with frame relay: 1-port ATM-IWU STM-1/STS-3c card -------------------------------- Values: 1..16
OBJECT-TYPE    
  INTEGER  

cktOspfCtd 1.3.6.1.4.1.277.1.6.1.1.125
The allowed cell delay: 4-port CBR E1/DS1 card ---------------------- The maximum allowed cell delay in msec
OBJECT-TYPE    
  INTEGER 1..100  

cktOspfCdv 1.3.6.1.4.1.277.1.6.1.1.126
The allowed cell delay variation: 4-port CBR E1/DS1 card ---------------------- The maximum allowed cell delay variation in msec
OBJECT-TYPE    
  INTEGER 100..1000  

cktOutPort 1.3.6.1.4.1.277.1.6.1.1.127
The outgoing port number for the adjacent VC entry in this switch.
OBJECT-TYPE    
  INTEGER  

cktOutVc 1.3.6.1.4.1.277.1.6.1.1.128
The adjacent VC entry corresponding to this circuit accross the bus.
OBJECT-TYPE    
  INTEGER  

cktRVc 1.3.6.1.4.1.277.1.6.1.1.129
The adjacent VC entry corresponding to this circuit accross the trunk.
OBJECT-TYPE    
  INTEGER  

cktEntryType 1.3.6.1.4.1.277.1.6.1.1.130
The internal type of circuit entry allocated by the circuit manager.
OBJECT-TYPE    
  INTEGER fr-user(1), as-trunk(2), on-trunk(3), lmi(4), multicast(5), mgmt(6), smds(7), split-multicast(8), control(9), atm-user(10), atm-leaf(11)  

cktDiagStr 1.3.6.1.4.1.277.1.6.1.1.131
Internal diagnostic information.
OBJECT-TYPE    
  OCTET STRING  

cktSvcAalType 1.3.6.1.4.1.277.1.6.1.1.132
The AAL type for this SVC.
OBJECT-TYPE    
  INTEGER aal1(1), unspecified(2), aal3-4(3), user-defined(4), aal5(5)  

cktSvcBBearerClass 1.3.6.1.4.1.277.1.6.1.1.133
The Broadband bearer capability class for this SVC.
OBJECT-TYPE    
  INTEGER unspecified(1), class-A(2), class-C(3), class-X(4), class-VP(5)  

cktSvcBBearerClippingSusc 1.3.6.1.4.1.277.1.6.1.1.134
The Broadband bearer capability clipping susceptibility for this SVC.
OBJECT-TYPE    
  INTEGER unspecified(1), not-susceptible(2), susceptible(3)  

cktSvcBBearerTmgReq 1.3.6.1.4.1.277.1.6.1.1.135
The Broadband bearer capability timing requirements for this SVC.
OBJECT-TYPE    
  INTEGER not-indicated(1), end-to-end(2), not-end-to-end(3)  

cktSvcBBearerTfcType 1.3.6.1.4.1.277.1.6.1.1.136
The Broadband bearer capability traffic type for this SVC.
OBJECT-TYPE    
  INTEGER not-indicated(1), cbr(2), vbr(3)  

cktAtmUPCEnable 1.3.6.1.4.1.277.1.6.1.1.137
Enable ATM UPC Function.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

cktRPriority 1.3.6.1.4.1.277.1.6.1.1.138
The priority level (0 through 3) for this circuit in the opposite direction. When port service type is defined as 'mono-class', this priority means the forward priority of the circuit. When port service type is defined as 'multi-class', this priority means the discard priority of the circuit.
OBJECT-TYPE    
  INTEGER  

cktRtPriority 1.3.6.1.4.1.277.1.6.1.1.139
The routing priority level of the circuit which is a 8 bit number where the 3-bit bumping priority is contained in bits 0-2 and the 4-bit bandwidth priority is contained in bits 3-6. For ATM multipoint ckts, bw and bumping priorities should be zero.
OBJECT-TYPE    
  INTEGER  

cktDeltaBc 1.3.6.1.4.1.277.1.6.1.1.140
The maximum number of bits that the network agree to transfer over the circuit as committed bits during the measurement interval under the CONDITION that the circuit still has POSITIVE committed bit (Bc) credits before receiving a frame but will have NEGATIVE Bc credits after accepting the frame. The range of this variable is 0 to 65,528 bits. By default, if not configured when creating the entry, it is set to 65,528 bits.
OBJECT-TYPE    
  INTEGER  

cktDeltaBe 1.3.6.1.4.1.277.1.6.1.1.141
The maximum number of bits that the network agree to transfer over the circuit as allowed excess bits during the measurement interval under the CONDITION that the circuit still has POSITIVE excess bit (Be) credits before receiving a frame but will have NEGATIVE Be credits after accepting the frame. The range of this variable is 0 to 65,528 bits. By default, if not configured when creating the entry, it is set to 65,528 bits.
OBJECT-TYPE    
  INTEGER  

cktDeltaRBc 1.3.6.1.4.1.277.1.6.1.1.142
The maximum number of bits that the network agree to transfer over the circuit as committed bits in the opposite direction during the measurement interval under the CONDITION that the circuit still has POSITIVE committed bit (Bc) credits before receiving a frame but will have NEGATIVE Bc credits after accepting the frame. The range of this variable is 0 to 65,528 bits. By default, if not configured when creating the entry, it is set to 65,528 bits.
OBJECT-TYPE    
  INTEGER  

cktDeltaRBe 1.3.6.1.4.1.277.1.6.1.1.143
The maximum number of bits that the network agree to transfer over the circuit as allowed excess bits in the opposite direction during the measurement interval under the CONDITION that the circuit still has POSITIVE excess bit (Be) credits before receiving a frame but will have NEGATIVE Be credits after accepting the frame. The range of this variable is 0 to 65,528 bits. By default, if not configured when creating the entry, it is set to 65,528 bits.
OBJECT-TYPE    
  INTEGER  

cktRedFrPcnt 1.3.6.1.4.1.277.1.6.1.1.144
The percentage of RED frame bits that are allowed to enter the network, during the measurement interval, under non-congestion condition. Its value range is 0 - 100 and default value is 100. Its calculation is as follows: cktRedFrPcn = (allowed RED frame bits)/(Bc+Be+allowed RED frame bits)
OBJECT-TYPE    
  INTEGER  

cktRedFrRPcnt 1.3.6.1.4.1.277.1.6.1.1.145
The percentage of RED frame bits that are allowed to enter the network in the opposite direction, during the measurement interval, under non-congestion condition. Its value range is 0 - 100 and default value is 100. Its calculation is as follows: cktRedFrRPcn = (allowed RED frame bits)/(rBc+rBe+allowed RED frame bits)
OBJECT-TYPE    
  INTEGER  

cktRateEnforceSchm 1.3.6.1.4.1.277.1.6.1.1.146
Variable used to indicate the rate enforcement scheme employed. 0: Slide window rate enforcement scheme 1: Jump window rate enforcement scheme 2: Simple rate enforcement scheme Default value is 2.
OBJECT-TYPE    
  INTEGER jump(1), simple(2)  

cktRateEnforceRSchm 1.3.6.1.4.1.277.1.6.1.1.147
Variable used to indicate the rate enforcement scheme employed in the opposite direction. 0: Slide window rate enforcement scheme 1: Jump window rate enforcement scheme 2: Simple rate enforcement scheme Default value is 2.
OBJECT-TYPE    
  INTEGER jump(1), simple(2)  

cktROde 1.3.6.1.4.1.277.1.6.1.1.148
This variable states whether graceful discard is enabled for the ckt in the opposite direction.
OBJECT-TYPE    
  INTEGER on(1)  

cktPrivateNet 1.3.6.1.4.1.277.1.6.1.1.149
If non-zero, indicates the private network that the circuit belongs to. If 0, the circuit has access to the entire public portion of the network.
OBJECT-TYPE    
  INTEGER  

cktPrivateNetOverflow 1.3.6.1.4.1.277.1.6.1.1.150
Indicates how private network circuits are handled, when the resources of the network have become exhausted. If set to use-public, the resources of the public network can be used during overflow conditions.
OBJECT-TYPE    
  INTEGER use-public(1)  

cktCustomerID 1.3.6.1.4.1.277.1.6.1.1.151
The Customer that owns this circuit. For Virtual Private Networking Support.
OBJECT-TYPE    
  INTEGER  

cktAtmCDVT 1.3.6.1.4.1.277.1.6.1.1.152
The Cell Delay Variation Tolerance for the VC
OBJECT-TYPE    
  INTEGER  

cktNdcEnable 1.3.6.1.4.1.277.1.6.1.1.153
Enable/disable Network Data Collection for a PVC on an IOM. The number of NDC-monitored PVCs is limited as follows: 30 per DS3 interface, 90 per OC3 interface, and 360 per OC12 interface.
OBJECT-TYPE    
  INTEGER off(1), on(2)  

cktInterworkingFrToAtmCLP 1.3.6.1.4.1.277.1.6.1.1.154
CLP mapping for Frame Relay To ATM Service Interworking.
OBJECT-TYPE    
  INTEGER clp1(1), fr-de(2)  

cktInterworkingFrToAtmDe 1.3.6.1.4.1.277.1.6.1.1.155
DE bit mapping for ATM To Frame Relay Service Interworking.
OBJECT-TYPE    
  INTEGER de1(1), atm-clp(2)  

cktNrtsCLP1 1.3.6.1.4.1.277.1.6.1.1.156
Whether to use the discard threshold as the CLP1 Discard threshold upon reception of a cell by the NRTS processor in the forward direction.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

cktNrtsDiscardClp0 1.3.6.1.4.1.277.1.6.1.1.157
The number of the CLP0 cells received and discarded by the NRTS processor.
OBJECT-TYPE    
  Counter  

cktNrtsDiscardClp1 1.3.6.1.4.1.277.1.6.1.1.158
The number of the CLP1 cells received and discarded by the NRTS processor.
OBJECT-TYPE    
  Counter  

cktMPEnableAMF 1.3.6.1.4.1.277.1.6.1.1.159
Whether the Multilink PPP PVC Attributes Modification Feature is enabled.
OBJECT-TYPE    
  INTEGER disableAMF(1), enableAMF(2)  

cktMPEligible 1.3.6.1.4.1.277.1.6.1.1.160
Whether this circuit is eligible to be a member of a Multilink PPP bundle.
OBJECT-TYPE    
  INTEGER isMPEligible(1), isNotMPEligible(2)  

cktMPForcedCaller 1.3.6.1.4.1.277.1.6.1.1.161
Whether this end of the circuit has been forced to be caller to support Multilink PPP PVC Attributes Modification Feature.
OBJECT-TYPE    
  INTEGER isMPForcedCaller(1), isNotMPForcedCaller(2)  

cktMPForcedCallee 1.3.6.1.4.1.277.1.6.1.1.162
Whether this end of the circuit has been forced to be callee to support Multilink PPP PVC Attributes Modification Feature.
OBJECT-TYPE    
  INTEGER isMPForcedCallee(1), isNotMPForcedCallee(2)  

cktFrameSize 1.3.6.1.4.1.277.1.6.1.1.163
The average frame size (measured in number of bytes) of the traffic on the circuit. If not configured, it is set to 280 (bytes) by default.
OBJECT-TYPE    
  INTEGER  

cktRFrameSize 1.3.6.1.4.1.277.1.6.1.1.164
The average frame size (measured in number of bytes) of the traffic on the circuit on the reverse direction. If not configured, it is set to 280 (bytes) by default.
OBJECT-TYPE    
  INTEGER  

cktRNrtsCLP1 1.3.6.1.4.1.277.1.6.1.1.165
Whether to use the discard threshold as the CLP1 Discard threshold upon reception of a cell by the NRTS processor in the reverse direction.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

cktBBearerAtmTransferCapability 1.3.6.1.4.1.277.1.6.1.1.166
The broadband bearer ATM transfer capability of this SVC. This object is not pertinent to IISP 3.x, UNI 3.x or Q.2931 signaling.
OBJECT-TYPE    
  INTEGER none(1), cbr(2), cbr-with-clr-01(3), vbr-rt(4), vbr-rt-with-clr-01(5), vbr-nrt(6), vbr-nrt-with-clr-01(7), abr(8)  

cktAtmFrameDiscard 1.3.6.1.4.1.277.1.6.1.1.167
The ATM frame discard state for this circuit.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

cktRAtmFrameDiscard 1.3.6.1.4.1.277.1.6.1.1.168
The reverse ATM frame discard state for this circuit.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

cktAbrFRMRTT 1.3.6.1.4.1.277.1.6.1.1.169
The ABR fixed RM round trip time for this SVC.
OBJECT-TYPE    
  INTEGER  

cktAbrICR 1.3.6.1.4.1.277.1.6.1.1.170
The ABR initial cell rate for this SVC.
OBJECT-TYPE    
  INTEGER  

cktRAbrICR 1.3.6.1.4.1.277.1.6.1.1.171
The reverse ABR initial cell rate for this SVC.
OBJECT-TYPE    
  INTEGER  

cktAbrRIF 1.3.6.1.4.1.277.1.6.1.1.172
The ABR rate increase factor for this SVC.
OBJECT-TYPE    
  INTEGER  

cktRAbrRIF 1.3.6.1.4.1.277.1.6.1.1.173
The reverse ABR rate increase factor for this SVC.
OBJECT-TYPE    
  INTEGER  

cktAbrRDF 1.3.6.1.4.1.277.1.6.1.1.174
The ABR rate decrease factor for this SVC.
OBJECT-TYPE    
  INTEGER  

cktRAbrRDF 1.3.6.1.4.1.277.1.6.1.1.175
The reverse ABR rate decrease factor for this SVC.
OBJECT-TYPE    
  INTEGER  

cktAbrTBE 1.3.6.1.4.1.277.1.6.1.1.176
The ABR transient buffer exposure for this SVC.
OBJECT-TYPE    
  INTEGER  

cktRAbrTBE 1.3.6.1.4.1.277.1.6.1.1.177
The reverse ABR transient buffer exposure for this SVC.
OBJECT-TYPE    
  INTEGER  

cktAbrNRM 1.3.6.1.4.1.277.1.6.1.1.178
The ABR NRM for this SVC.
OBJECT-TYPE    
  INTEGER  

cktRAbrNRM 1.3.6.1.4.1.277.1.6.1.1.179
The reverse ABR NRM for this SVC.
OBJECT-TYPE    
  INTEGER  

cktAbrTRM 1.3.6.1.4.1.277.1.6.1.1.180
The ABR TRM for this SVC.
OBJECT-TYPE    
  INTEGER  

cktRAbrTRM 1.3.6.1.4.1.277.1.6.1.1.181
The reverse ABR TRM for this SVC.
OBJECT-TYPE    
  INTEGER  

cktAbrCDF 1.3.6.1.4.1.277.1.6.1.1.182
The ABR CDF for this SVC.
OBJECT-TYPE    
  INTEGER  

cktRAbrCDF 1.3.6.1.4.1.277.1.6.1.1.183
The reverse ABR CDF for this SVC.
OBJECT-TYPE    
  INTEGER  

cktAbrADTF 1.3.6.1.4.1.277.1.6.1.1.184
The ABR ADTF for this SVC.
OBJECT-TYPE    
  INTEGER  

cktRAbrADTF 1.3.6.1.4.1.277.1.6.1.1.185
The reverse ABR ADTF for this SVC.
OBJECT-TYPE    
  INTEGER  

cktAccumCTD 1.3.6.1.4.1.277.1.6.1.1.186
The accumulated cell(frame) transfer delay for this circuit, in microseconds. The distinguished value 0x00FFFFFF means not valid.
OBJECT-TYPE    
  INTEGER  

cktAccumCDV 1.3.6.1.4.1.277.1.6.1.1.187
The accumulated cell delay variation for this circuit, in microseconds. The distinguished value 0x00FFFFFF means not valid.
OBJECT-TYPE    
  INTEGER  

cktAccumRCDV 1.3.6.1.4.1.277.1.6.1.1.188
The accumulated reverse cell delay variation for this circuit, in microseconds. The distinguished value 0x00FFFFFF means not valid.
OBJECT-TYPE    
  INTEGER  

cktCLR 1.3.6.1.4.1.277.1.6.1.1.189
The cell loss ratio requirement, expressed as a negative exponent of 10. The default value 255 represents any cell loss ratio acceptable.
OBJECT-TYPE    
  INTEGER  

cktRCLR 1.3.6.1.4.1.277.1.6.1.1.190
The reverse cell loss ratio requirement, expressed as a negative exponent of 10. The default value 255 represents any cell loss ratio acceptable.
OBJECT-TYPE    
  INTEGER  

cktAtmLijId 1.3.6.1.4.1.277.1.6.1.1.191
The Leaf Initiated Join ID of the PMP SVC rooted at this interface.
OBJECT-TYPE    
  INTEGER  

cktAtmLijType 1.3.6.1.4.1.277.1.6.1.1.192
The Leaf Initiated Join type of the PMP SVC rooted at this interface.
OBJECT-TYPE    
  INTEGER not-lij(1), root-lij(2), network-lij(3)  

cktRtLastDelay 1.3.6.1.4.1.277.1.6.1.1.193
The last round-trip delay (micro-seconds).
OBJECT-TYPE    
  INTEGER  

cktRtAccuMinDelay 1.3.6.1.4.1.277.1.6.1.1.194
The prev min round-trip delay (micro-seconds).
OBJECT-TYPE    
  INTEGER  

cktRtAccuMaxDelay 1.3.6.1.4.1.277.1.6.1.1.195
The prev max round-trip delay (micro-seconds).
OBJECT-TYPE    
  INTEGER  

cktRtAccuAvgDelay 1.3.6.1.4.1.277.1.6.1.1.196
The prev avg round-trip delay (micro-seconds).
OBJECT-TYPE    
  INTEGER  

cktQosIntPeriod 1.3.6.1.4.1.277.1.6.1.1.197
The number of periods for calculating qos params.
OBJECT-TYPE    
  INTEGER  

cktAtmOutOAMClp0Cells 1.3.6.1.4.1.277.1.6.1.1.198
The number of OAM CLP0 cells transmitted on this circuit. For BIO1 card (on Garnet Platform), this count is not reported separately - see cktEntry 99.
OBJECT-TYPE    
  Counter  

cktAtmOutOAMClp1Cells 1.3.6.1.4.1.277.1.6.1.1.199
The number of OAM CLP1 cells transmitted on this circuit. For BIO1 card (on Garnet Platform), this count is not reported separately - see cktEntry 100.
OBJECT-TYPE    
  Counter  

cktReqCTD 1.3.6.1.4.1.277.1.6.1.1.200
The requested cell/frame delay variation for this circuit, in microseconds. The range for PVC is 1 - 0x00FFFFFF. The default is 0x00FFFFFF, which means not valid.
OBJECT-TYPE    
  INTEGER  

cktInOctetsPeak 1.3.6.1.4.1.277.1.6.1.1.201
The 5-minute peak value of the number of inbound octets (bytes) for the circuit - from Bulk Statistics.
OBJECT-TYPE    
  Counter  

cktOutOctetsPeak 1.3.6.1.4.1.277.1.6.1.1.202
The 5-minute peak value of the number of outbound octets (bytes) for the circuit - from Bulk Statistics.
OBJECT-TYPE    
  Counter  

cktInDEOctetsPeak 1.3.6.1.4.1.277.1.6.1.1.203
The 5-minute peak value of the number of inbound DE-marked octets (bytes) for the circuit - from Bulk Statistics.
OBJECT-TYPE    
  Counter  

cktOutDEOctetsPeak 1.3.6.1.4.1.277.1.6.1.1.204
The 5-minute peak value of the number of outbound DE-marked octets (bytes) for the circuit - from Bulk Statistics.
OBJECT-TYPE    
  Counter  

cktInODEOctetsPeak 1.3.6.1.4.1.277.1.6.1.1.205
The 5-minute peak value of the number of inbound ODE-marked octets (bytes) for the circuit - from Bulk Statistics.
OBJECT-TYPE    
  Counter  

cktOutODEOctetsPeak 1.3.6.1.4.1.277.1.6.1.1.206
The 5-minute peak value of the number of outbound ODE-marked octets (bytes) for the circuit - from Bulk Statistics.
OBJECT-TYPE    
  Counter  

cktAdminCostThreshold 1.3.6.1.4.1.277.1.6.1.1.207
Maximum allowable admin cost for the circuit. If no paths are available with cost less than or equal to this value, the circuit is not established. DEFVAL is 0 which means invalid, valid values range from 1 to 0xFFFFFFFF.
OBJECT-TYPE    
  INTEGER  

cktAtmSvcServiceCategory 1.3.6.1.4.1.277.1.6.1.1.208
The derived service category in the forward direction for this ATM SVC.
OBJECT-TYPE    
  INTEGER cbr(1), vbr1(2), vbr2(3), ubr-abr(4), unspecified(5)  

cktAtmSvcRServiceCategory 1.3.6.1.4.1.277.1.6.1.1.209
The derived service category in the reverse direction for this ATM SVC.
OBJECT-TYPE    
  INTEGER cbr(1), vbr1(2), vbr2(3), ubr-abr(4), unspecified(5)  

cktInterworkingFrToAtmEFCI 1.3.6.1.4.1.277.1.6.1.1.210
EFCI mapping for Frame Relay To ATM Service Interworking.
OBJECT-TYPE    
  INTEGER fr-fecn(1), efci0(2)  

cktDiagSARMon 1.3.6.1.4.1.277.1.6.1.1.211
Used to start or stop flow on the inbound/outbound ATMizer without informing the PPC.
OBJECT-TYPE    
  INTEGER flowOnInbound(1), flowOffInbound(2), flowOnOutbound(3), flowOffOutbound(4), flowOnInboundOutbound(5), flowOffInboundOutbound(6)  

cktAdminCostReal 1.3.6.1.4.1.277.1.6.1.1.212
Actual value of total administration cost of a circuit. Ranges from 0 to 0xFFFFFFFF.
OBJECT-TYPE    
  INTEGER  

cktAtmInClp0Cells 1.3.6.1.4.1.277.1.6.1.1.213
The Number of ATM CLP 0 cells received on a VC (VPC or VCC).
OBJECT-TYPE    
  Counter  

cktAtmInClp1Cells 1.3.6.1.4.1.277.1.6.1.1.214
The Number of ATM CLP 1 cells received on a VC (VPC or VCC).
OBJECT-TYPE    
  Counter  

cktATMAAL5CRC32Error 1.3.6.1.4.1.277.1.6.1.1.215
Number of received AAL5 packets with CRC32 errors.
OBJECT-TYPE    
  Counter  

cktATMAAL5CPIError 1.3.6.1.4.1.277.1.6.1.1.216
Number of received AAL5 packets with CPI errors The only valid value currently defined for the CPI field is all zeros
OBJECT-TYPE    
  Counter  

cktATMAAL5LengthError 1.3.6.1.4.1.277.1.6.1.1.217
Number of received AAL5 packets which satisfied one of the following error conditions: 1. number of received cells * 48 bytes - length value in trailer > 55 bytes 2. number of received cells * 48 bytes - length value in trailer < 8 bytes
OBJECT-TYPE    
  Counter  

cktATMAAL5ReassemblyTimerError 1.3.6.1.4.1.277.1.6.1.1.218
Number of expired reassembly timers
OBJECT-TYPE    
  Counter  

cktATMAAL5MaxNrSegError 1.3.6.1.4.1.277.1.6.1.1.219
Number of received AAL5 packets which exceeds the maximum allowed length
OBJECT-TYPE    
  Counter  

cktIWF1490to1483Error 1.3.6.1.4.1.277.1.6.1.1.220
Number of Frames received that failed the rfc1490 to rfc 1483 header translation. This error counter indicates that frames being recevied from the frame relay side of the connection have an incorrectly formatted 1490 header and cannot be translated. See cktIWF1490to1483LastBadHeader for the last received 1490 header
OBJECT-TYPE    
  Counter  

cktIWF1490to1483LastBadHeader 1.3.6.1.4.1.277.1.6.1.1.221
Ascii string of the first 8 bytes of the header from the last frame discarded because the 1490 to 1483 header translation failed. The string displays the hexidecimal values for the data bytes
OBJECT-TYPE    
  DisplayString  

cktIWF1483to1490Error 1.3.6.1.4.1.277.1.6.1.1.222
Number of Frames received that failed the rfc1483 to rfc 1490 header translation. This error counter indicates that frames being recevied from the atm side of the connection have an incorrectly formatted 1483 header and cannot be translated. See cktIWF1483to1490LastBadHeader for the last received 1490 header
OBJECT-TYPE    
  Counter  

cktIWF1483to1490LastBadHeader 1.3.6.1.4.1.277.1.6.1.1.223
Ascii string of the first 10 bytes of the header from the last frame discarded because the 1483 to 1490 header translation failed. The string displays the hexidecimal values for the data bytes
OBJECT-TYPE    
  DisplayString  

cktLeafTable 1.3.6.1.4.1.277.1.6.2
A table containing information about leaves of multipoint circuits.
OBJECT-TYPE    
  SEQUENCE OF  
    CktLeafEntry

cktLeafEntry 1.3.6.1.4.1.277.1.6.2.1
The objects relevant to a single leaf in a multipoint circuit.
OBJECT-TYPE    
  CktLeafEntry  

cktLeafSrcIfIndex 1.3.6.1.4.1.277.1.6.2.1.1
The interface ID at this node's ingress port for the corresponding multipoint circuit.
OBJECT-TYPE    
  Index  

cktLeafSrcDlci 1.3.6.1.4.1.277.1.6.2.1.2
The DLCI, if a frame relay circuit, or concatenated VPI and VCI, if an ATM circuit, at this node's ingress port for the corresponding multipoint circuit.
OBJECT-TYPE    
  INTEGER  

cktLeafEndpointIndex 1.3.6.1.4.1.277.1.6.2.1.3
An identifier unique to this leaf for the corresponding multipoint circuit.
OBJECT-TYPE    
  INTEGER  

cktLeafCreationTime 1.3.6.1.4.1.277.1.6.2.1.4
The value of sysUpTime when this leaf was created for the corresponding multipoint circuit.
OBJECT-TYPE    
  TimeTicks  

cktLeafEgressIfIndex 1.3.6.1.4.1.277.1.6.2.1.5
The interface ID at this node's egress port for this leaf's segment of the corresponding multipoint circuit.
OBJECT-TYPE    
  Index  

cktLeafEgressDlci 1.3.6.1.4.1.277.1.6.2.1.6
The DLCI, if a frame relay circuit, or concatenated VPI and VCI, if an ATM circuit, at this node's egress port for this leaf's segment of the corresponding multipoint circuit.
OBJECT-TYPE    
  INTEGER  

cktLeafDestNodeId 1.3.6.1.4.1.277.1.6.2.1.7
The node ID of the node where this leaf terminates.
OBJECT-TYPE    
  INTEGER  

cktLeafDestIfIndex 1.3.6.1.4.1.277.1.6.2.1.8
The interface ID at the egress port of the destination node for this leaf, if this is a PVC.
OBJECT-TYPE    
  Index  

cktLeafDestDlci 1.3.6.1.4.1.277.1.6.2.1.9
The DLCI, if a frame relay circuit, or concatenated VPI and VCI, if an ATM circuit, at this node's destination port for the corresponding multipoint circuit.
OBJECT-TYPE    
  INTEGER  

cktLeafSvcCallingParty 1.3.6.1.4.1.277.1.6.2.1.10
The calling party number for this leaf, if this is an SVC.
OBJECT-TYPE    
  OCTET STRING  

cktLeafSvcCalledParty 1.3.6.1.4.1.277.1.6.2.1.11
The called party number for this leaf, if this is an SVC.
OBJECT-TYPE    
  OCTET STRING  

cktLeafAdminStatus 1.3.6.1.4.1.277.1.6.2.1.12
The desired state for the leaf entry.
OBJECT-TYPE    
  INTEGER down(1), up(2)  

cktLeafVcState 1.3.6.1.4.1.277.1.6.2.1.13
The current state of the leaf PVC segment in the Cascade network.
OBJECT-TYPE    
  INTEGER inactive(1), retry(2), calling(3), wcbdeact(4), wcbdelete(5), active(6), svcall(7), svclr(8), backedup(9), wcbbkdp(10), wcbreact(11), slowretry(12)  

cktLeafOperStatus 1.3.6.1.4.1.277.1.6.2.1.14
The current operational status of the entire leaf PVC.
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

cktLeafDceState 1.3.6.1.4.1.277.1.6.2.1.15
The DCE state of the circuit.
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

cktLeafDteStatus 1.3.6.1.4.1.277.1.6.2.1.16
The DTE status of the circuit.
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

cktLeafDteState 1.3.6.1.4.1.277.1.6.2.1.17
The DTE state of the circuit.
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

cktLeafVcPtr 1.3.6.1.4.1.277.1.6.2.1.18
An 8-byte Octect string indicating the vc pointer.
OBJECT-TYPE    
  OCTET STRING  

cktLeafHopCnt 1.3.6.1.4.1.277.1.6.2.1.19
The count of hops along the circuit path. (Max is 16)
OBJECT-TYPE    
  INTEGER  

cktLeafPath 1.3.6.1.4.1.277.1.6.2.1.20
The circuit path consisting a sequence of outbound interface indexes at nodes along the established circuit. The format is interface:interface:interface......
OBJECT-TYPE    
  OCTET STRING  

cktLeafFailReason 1.3.6.1.4.1.277.1.6.2.1.21
The reason for the PVC establishment failure.
OBJECT-TYPE    
  INTEGER admindown(1), novcbuff(2), nobw(3), noroute(4), timeout(5), nopdubuff(6), nodest(7), trkrnr(8), trkdown(9), balancereroute(10), dead(11), defpathreroute(12), nidown(13), otherpvcsegdown(14), otherpvcsegrnr(15), usingaltpathwarning(16), iopdown(17), numsgbuffer(18), noport(19), misconfig(20), svcsetupfail(21), srcbackedup(22), srcunknown(23), dstunknown(24), bkpdlcicollision(25), oldrevinpath(26), smdsmgmttrunk(27), nevercalled(28), bothendptbackup(29), pvcroutemgttrunk(30), nomultipointparent(31), pvcroutefail(32), novpivci(33)  

cktLeafFailNode 1.3.6.1.4.1.277.1.6.2.1.22
The node which causes the PVC failure.
OBJECT-TYPE    
  INTEGER  

cktLeafFailPort 1.3.6.1.4.1.277.1.6.2.1.23
The port on the fail node which causes the PVC failure.
OBJECT-TYPE    
  INTEGER  

cktLeafHelloCounter 1.3.6.1.4.1.277.1.6.2.1.24
Number of PVC hello pdu frames received in the VC entry of the called side.
OBJECT-TYPE    
  INTEGER  

cktLeafHelloAckCounter 1.3.6.1.4.1.277.1.6.2.1.25
Number of PVC hello Ack pdu frames received in the VC entry of the calling side.
OBJECT-TYPE    
  INTEGER  

cktLeafAtmVPI 1.3.6.1.4.1.277.1.6.2.1.26
VPI value in the ATM cell header
OBJECT-TYPE    
  INTEGER  

cktLeafAtmVCI 1.3.6.1.4.1.277.1.6.2.1.27
VCI value in the ATM cell header
OBJECT-TYPE    
  INTEGER  

cktLeafType 1.3.6.1.4.1.277.1.6.2.1.28
1 if a permanent virtual circuit; 2 if a switched virtual circuit.
OBJECT-TYPE    
  INTEGER pvc(1), svc(2)  

cktLeafAtmInCells 1.3.6.1.4.1.277.1.6.2.1.29
The Number of ATM cells received on a VCC.
OBJECT-TYPE    
  Counter  

cktLeafAtmOutCells 1.3.6.1.4.1.277.1.6.2.1.30
The Number of ATM cells transmitted on a VCC.
OBJECT-TYPE    
  Counter  

cktLeafAtmInDiscardedClp0Cells 1.3.6.1.4.1.277.1.6.2.1.31
The Number of ATM CLP0 cells received and discarded on a VCC.
OBJECT-TYPE    
  Counter  

cktLeafAtmInDiscardedClp1Cells 1.3.6.1.4.1.277.1.6.2.1.32
The Number of ATM CLP1 cells received and discarded on a VCC.
OBJECT-TYPE    
  Counter  

cktLeafAtmInPassedClp0Cells 1.3.6.1.4.1.277.1.6.2.1.33
The Number of ATM CLP 0 cells received and passed UPC on a VCC.
OBJECT-TYPE    
  Counter  

cktLeafAtmInPassedClp1Cells 1.3.6.1.4.1.277.1.6.2.1.34
The Number of ATM CLP 1 cells received and passed UPC on a VCC.
OBJECT-TYPE    
  Counter  

cktLeafAtmInTaggedCells 1.3.6.1.4.1.277.1.6.2.1.35
The Number of ATM cells received and tagged on a VCC.
OBJECT-TYPE    
  Counter  

cktLeafAtmOutClp0Cells 1.3.6.1.4.1.277.1.6.2.1.36
The Number of ATM CLP 0 cells transmitted on a VCC.
OBJECT-TYPE    
  Counter  

cktLeafAtmOutClp1Cells 1.3.6.1.4.1.277.1.6.2.1.37
The Number of ATM CLP 1 cells transmitted on a VCC.
OBJECT-TYPE    
  Counter  

cktSmdsRtTable 1.3.6.1.4.1.277.1.6.3
A table containing information about destination, VC, hops and routes.
OBJECT-TYPE    
  SEQUENCE OF  
    CktSmdsRtEntry

cktSmdsRtEntry 1.3.6.1.4.1.277.1.6.3.1
The information regarding routes from a node to all its neighbors.
OBJECT-TYPE    
  CktSmdsRtEntry  

cktSmdsRemoteNode 1.3.6.1.4.1.277.1.6.3.1.1
The nodeId of the node to which a rought is sought.
OBJECT-TYPE    
  INTEGER  

cktSmdsHopCnt 1.3.6.1.4.1.277.1.6.3.1.2
The number of hops to reach the desired destination node.
OBJECT-TYPE    
  INTEGER  

cktSmdsRoute 1.3.6.1.4.1.277.1.6.3.1.3
The out-going Interface Id of each of the nodes in the path.
OBJECT-TYPE    
  OCTET STRING  

cktSmdsLocalPort 1.3.6.1.4.1.277.1.6.3.1.4
The out-going local portId.
OBJECT-TYPE    
  INTEGER  

cktSmdsRemotePort 1.3.6.1.4.1.277.1.6.3.1.5
The remote portId of the destination nodeId.
OBJECT-TYPE    
  INTEGER  

cktSmdsVcState 1.3.6.1.4.1.277.1.6.3.1.6
The state of the circuit.
OBJECT-TYPE    
  INTEGER  

card 1.3.6.1.4.1.277.1.7
OBJECT IDENTIFIER    

nodeSwDownloadComplete 1.3.6.1.4.1.277.1.7
This trap indicates that a software download was complete.
TRAP-TYPE    
  nodeSwFilename  

cardNumber 1.3.6.1.4.1.277.1.7.1
The number of manageable cards physically present in this node. Standby cards are not considered manageable.
OBJECT-TYPE    
  INTEGER  

cardTable 1.3.6.1.4.1.277.1.7.2
A list of cardEntry's. The number of entries is given by the value of cardNumber
OBJECT-TYPE    
  SEQUENCE OF  
    CardEntry

cardEntry 1.3.6.1.4.1.277.1.7.2.1
The card entry contains objects relevant to managing intelligent cards.
OBJECT-TYPE    
  CardEntry  

cardLogicalSlotId 1.3.6.1.4.1.277.1.7.2.1.1
The logical slot number of this card. This is used as an index for the cardTable. In redundant configurations, this can be the physical slot number of either redundant card. In non redundant configurations, this is the same as cardPhysicalSlotId.
OBJECT-TYPE    
  INTEGER  

cardPhysicalSlotId 1.3.6.1.4.1.277.1.7.2.1.2
The physical slot number of this card. This can be different from cardLogicalSlotId in redundant configurations.
OBJECT-TYPE    
  INTEGER  

cardAdminType 1.3.6.1.4.1.277.1.7.2.1.3
The desired card type.
OBJECT-TYPE    
  CardTypes  

cardOperType 1.3.6.1.4.1.277.1.7.2.1.4
The actual card type.
OBJECT-TYPE    
  CardTypes  

cardState 1.3.6.1.4.1.277.1.7.2.1.5
The state of this card.
OBJECT-TYPE    
  INTEGER present(1), loading(2), start(3), init(4), sync(5), syncdone(6), ready(7), active(8), stopped(9), down(10), debug(11), offlinediag(12)  

cardAdminStatus 1.3.6.1.4.1.277.1.7.2.1.6
The desired status of this card.
OBJECT-TYPE    
  CardStatuses  

cardOperStatus 1.3.6.1.4.1.277.1.7.2.1.7
The current status of this card.
OBJECT-TYPE    
  CardStatuses  

cardDiagStatus 1.3.6.1.4.1.277.1.7.2.1.8
The current diagnostics status of this card, as determined by background diagnostics.
OBJECT-TYPE    
  INTEGER ok(1), marginal(2)  

cardRedundConfig 1.3.6.1.4.1.277.1.7.2.1.9
Is the card configured for redundancy?
OBJECT-TYPE    
  INTEGER configured(1)  

cardRedundSlotMask 1.3.6.1.4.1.277.1.7.2.1.10
A 32-bit mask indicating the slot position of this card and its redundant partner. The low bit is slot 1 and the high bit is slot 32.
OBJECT-TYPE    
  INTEGER  

cardRedundActual 1.3.6.1.4.1.277.1.7.2.1.11
Is the card currently connected to a redundant card?
OBJECT-TYPE    
  INTEGER connected(1), not-connected(2)  

cardRedundState 1.3.6.1.4.1.277.1.7.2.1.12
The current redundancy state of this card. Exception: when used as an index for the following objects: cardAdminType, cardAdminCapability, and cardAdminStatus, the value 1 indicates the card of the redundant pair in the lower-numbered slot, and the value 2 indicates the card in the higher-numbered slot.
OBJECT-TYPE    
  INTEGER active(1), standby(2)  

cardToRedundant 1.3.6.1.4.1.277.1.7.2.1.13
Instructs the standby card to reset the active card and take over as new active card. The reset takes place after specified time ticks have elapsed. A value of 0 indicates cancellation of the previously scheduled request.
OBJECT-TYPE    
  TimeTicks  

cardDiagNonFatalSource 1.3.6.1.4.1.277.1.7.2.1.14
Source who reported last non-fatal error.
OBJECT-TYPE    
  INTEGER power-on-diagnostics(1), background-diagnostics(2), fault(3), frame-heap(4), redundancy(5), system-level(6), card-level(7), i960-data-structures(8), general(9), data-alignment(10), device-driver-level(11)  

cardDiagNonFatalTime 1.3.6.1.4.1.277.1.7.2.1.15
Time the last non-fatal error was reported.
OBJECT-TYPE    
  TimeTicks  

cardDiagNonFatalErrMajor 1.3.6.1.4.1.277.1.7.2.1.16
Major error code of last non-fatal error.
OBJECT-TYPE    
  INTEGER  

cardDiagNonFatalErrMinor 1.3.6.1.4.1.277.1.7.2.1.17
Minor error code of last non-fatal error.
OBJECT-TYPE    
  INTEGER  

cardDiagNonFatalStr 1.3.6.1.4.1.277.1.7.2.1.18
Ascii string describing last non-fatal error.
OBJECT-TYPE    
  DisplayString  

cardDiagFatalSource 1.3.6.1.4.1.277.1.7.2.1.19
Source who reported last fatal error.
OBJECT-TYPE    
  INTEGER power-on-diagnostics(1), background-diagnostics(2), fault(3), frame-heap(4), redundancy(5), system-level(6), card-level(7), i960-data-structures(8), general(9), data-alignment(10), device-driver-level(11)  

cardDiagFatalTime 1.3.6.1.4.1.277.1.7.2.1.20
Time the last fatal error was reported.
OBJECT-TYPE    
  TimeTicks  

cardDiagFatalErrMajor 1.3.6.1.4.1.277.1.7.2.1.21
Major error code of last fatal error.
OBJECT-TYPE    
  INTEGER  

cardDiagFatalErrMinor 1.3.6.1.4.1.277.1.7.2.1.22
Minor error code of last fatal error.
OBJECT-TYPE    
  INTEGER  

cardDiagFatalStr 1.3.6.1.4.1.277.1.7.2.1.23
Ascii string describing last fatal error.
OBJECT-TYPE    
  DisplayString  

cardDiagFatalReboots 1.3.6.1.4.1.277.1.7.2.1.24
Number of times the switch has re-booted since last fatal error was reported.
OBJECT-TYPE    
  Counter  

cardDiagFatalAddress 1.3.6.1.4.1.277.1.7.2.1.25
Address switch was executing when it encountered fatal error.
OBJECT-TYPE    
  INTEGER  

cardDiagBackgroundPasses 1.3.6.1.4.1.277.1.7.2.1.26
Number of passes made by the background diagnostics.
OBJECT-TYPE    
  Counter  

cardDiagBackgroundFailures 1.3.6.1.4.1.277.1.7.2.1.27
Number of failures discovered by background diagnostics.
OBJECT-TYPE    
  Counter  

cardDiagBackgroundSuccesses 1.3.6.1.4.1.277.1.7.2.1.28
Number of successful passes by background diagnostics.
OBJECT-TYPE    
  Counter  

cardDiagLEDReset 1.3.6.1.4.1.277.1.7.2.1.29
Change the card state from marginal to active. Change the LED from yellow to green.
OBJECT-TYPE    
  INTEGER state-to-active(1)  

cardDiagPowerExtensive 1.3.6.1.4.1.277.1.7.2.1.30
Should power on diagnostics do slower, extensive testing, or fast testing?
OBJECT-TYPE    
  INTEGER extensive-tests(1)  

cardCpuUtil 1.3.6.1.4.1.277.1.7.2.1.31
The CPU utilization percentage for packet processing on this intelligent card.
OBJECT-TYPE    
  Gauge  

cardMemoryUsage 1.3.6.1.4.1.277.1.7.2.1.32
The memory utilization, in terms of free bytes, for this intelligent card.
OBJECT-TYPE    
  Gauge  

cardMaxVCs 1.3.6.1.4.1.277.1.7.2.1.33
The number of available VC entries on this card.
OBJECT-TYPE    
  Gauge  

cardInUseVCs 1.3.6.1.4.1.277.1.7.2.1.34
The number of currently in use VC entries on this card.
OBJECT-TYPE    
  Gauge  

cardFreeVCs 1.3.6.1.4.1.277.1.7.2.1.35
The number of currently free VC entries on this card.
OBJECT-TYPE    
  Gauge  

cardInOctets 1.3.6.1.4.1.277.1.7.2.1.36
The total number of octets received on this card, including framing bytes.
OBJECT-TYPE    
  Counter  

cardInPkts 1.3.6.1.4.1.277.1.7.2.1.37
The total number of packets received on this card.
OBJECT-TYPE    
  Counter  

cardOutOctets 1.3.6.1.4.1.277.1.7.2.1.38
The total number of octets transmitted out of this card, including framing bytes.
OBJECT-TYPE    
  Counter  

cardOutPkts 1.3.6.1.4.1.277.1.7.2.1.39
The total number of packets requested to be transmitted out of this card, including those that were discarded or not sent.
OBJECT-TYPE    
  Counter  

cardToWarmboot 1.3.6.1.4.1.277.1.7.2.1.40
Warm boots the card after the specified time ticks have elapsed. A value of 0 indicates cancellation of the previously scheduled re-boot request.
OBJECT-TYPE    
  TimeTicks  

cardToColdboot 1.3.6.1.4.1.277.1.7.2.1.41
Cold boots the card after the specified time ticks have elapsed. A value of 0 indicates cancellation of the previously scheduled re-boot request.
OBJECT-TYPE    
  TimeTicks  

cardModel 1.3.6.1.4.1.277.1.7.2.1.42
The part number of the card.
OBJECT-TYPE    
  DisplayString  

cardSerial 1.3.6.1.4.1.277.1.7.2.1.43
The serial number of the card.
OBJECT-TYPE    
  DisplayString  

cardSwRev 1.3.6.1.4.1.277.1.7.2.1.44
The software rev number (major.minor).
OBJECT-TYPE    
  DisplayString  

cardHwRev 1.3.6.1.4.1.277.1.7.2.1.45
The hardware rev number (major.minor).
OBJECT-TYPE    
  DisplayString  

cardEpromRev 1.3.6.1.4.1.277.1.7.2.1.46
The EPROM firmware rev number (major.minor).
OBJECT-TYPE    
  DisplayString  

cardName 1.3.6.1.4.1.277.1.7.2.1.47
The name of this card
OBJECT-TYPE    
  DisplayString  

cardCktGroupTrap 1.3.6.1.4.1.277.1.7.2.1.48
This is a ( 4 + n*134 ) byte octet string where n => 1. The first and second byte is the interface/slot id of the link/IOP going down or link goes up. The third byte is the reason why circuits go down: 1 is a user link goes down, 2 is a trunk link goes down, 3 is an IOP goes down and 4 is an user link goes up The fourth byte is the count of entries in the following circuit bit map array. Each circuit bit map entry is 134 bytes. The first 2 bytes is the IOP slot on which dlci's are defined. The second 2 bytes is the Physical port ID on which dlci's are defined. The third 2 bytes is the interface id on which dlci's are defined. The following 128 bytes (1024 bits) is a bit map for dlci's defined on the interface. The left-most bit of the first byte represent dlci 0 and the right-most bit of the 128th byte represent dlci 1023. If a bit is set, it means the corresponding dlci on that interface is up/down.
OBJECT-TYPE    
  OCTET STRING  

cardOutBtus 1.3.6.1.4.1.277.1.7.2.1.49
The number of bus transfer units sent by this card.
OBJECT-TYPE    
  Counter  

cardInGoodBtus 1.3.6.1.4.1.277.1.7.2.1.50
The number of good bus transfer units received by this card.
OBJECT-TYPE    
  Counter  

cardInErrorBtus 1.3.6.1.4.1.277.1.7.2.1.51
The number of bus transfer units received with errors.
OBJECT-TYPE    
  Counter  

cardInNoVcBtus 1.3.6.1.4.1.277.1.7.2.1.52
The number of bus transfer units discarded because no circuit was found.
OBJECT-TYPE    
  Counter  

cardInLinkDownBtus 1.3.6.1.4.1.277.1.7.2.1.53
The number of bus transfer units discarded because the outgoing link was inactive.
OBJECT-TYPE    
  Counter  

cardInNoBufferBtus 1.3.6.1.4.1.277.1.7.2.1.54
The number of bus transfer units discarded because no buffer was available.
OBJECT-TYPE    
  Counter  

cardInForwardBitBtus 1.3.6.1.4.1.277.1.7.2.1.55
The number of bus transfer units discarded because the circuit forward bit was off.
OBJECT-TYPE    
  Counter  

cardDiagTestId 1.3.6.1.4.1.277.1.7.2.1.56
Identification of the diagnostics tests to be run.
OBJECT-TYPE    
  INTEGER  

cardDiagTestRuns 1.3.6.1.4.1.277.1.7.2.1.57
The number of passes of the diagnostics tests to be run. The default value is 1.
OBJECT-TYPE    
  INTEGER  

cardDiagState 1.3.6.1.4.1.277.1.7.2.1.58
The current state of the foreground diagnostics on this card.
OBJECT-TYPE    
  INTEGER active(1)  

cardDiagOptionStr 1.3.6.1.4.1.277.1.7.2.1.59
Optional parameters to the diagnostic.
OBJECT-TYPE    
  OCTET STRING  

cardDiagPasses 1.3.6.1.4.1.277.1.7.2.1.60
Number of successful diagnostic passes.
OBJECT-TYPE    
  Counter  

cardDiagFailures 1.3.6.1.4.1.277.1.7.2.1.61
Number of failed diagnostic passes.
OBJECT-TYPE    
  Counter  

cardDiagResultString 1.3.6.1.4.1.277.1.7.2.1.62
Description of last diagnostic failure.
OBJECT-TYPE    
  DisplayString  

cardFrameMemoryUtil 1.3.6.1.4.1.277.1.7.2.1.63
The percentage of frame memory utilization on this intelligent card.
OBJECT-TYPE    
  Gauge  

cardResetPram 1.3.6.1.4.1.277.1.7.2.1.64
Setting this to 1 causes a reset of PRAM on the corresponding card.
OBJECT-TYPE    
  INTEGER reset-pram(1)  

cardMemoryUtil 1.3.6.1.4.1.277.1.7.2.1.65
The percentage of system memory utilization on this intelligent card.
OBJECT-TYPE    
  Gauge  

cardFrameMemoryUsage 1.3.6.1.4.1.277.1.7.2.1.66
The frame memory utilization, in terms of free bytes, for this intelligent card.
OBJECT-TYPE    
  Gauge  

cardUpTime 1.3.6.1.4.1.277.1.7.2.1.67
The time (in hundredths of a second) since this card was last booted.
OBJECT-TYPE    
  TimeTicks  

cardPramChecksum 1.3.6.1.4.1.277.1.7.2.1.68
The PRAM checksum for this card.
OBJECT-TYPE    
  INTEGER  

cardPhysicalIndex 1.3.6.1.4.1.277.1.7.2.1.69
The physical slot id of this card.
OBJECT-TYPE    
  INTEGER  

cardExternalClockRate 1.3.6.1.4.1.277.1.7.2.1.70
The external clock rate for DSX1, T1 and E1 cards. The value is specified in units of 8KHz and can range from 1 to 255.
OBJECT-TYPE    
  INTEGER  

cardShootState 1.3.6.1.4.1.277.1.7.2.1.71
Specifies whether the system monitor on the CP should shoot this card if it's unreachable. The default is enabled. The card index used in the binding refers to a physical card.
OBJECT-TYPE    
  INTEGER shoot-enabled(1)  

cardEraseAll 1.3.6.1.4.1.277.1.7.2.1.72
When set to 1, erases program flash and PRAM on specified card.
OBJECT-TYPE    
  INTEGER erase-all(1)  

cardAdminCapability 1.3.6.1.4.1.277.1.7.2.1.73
The desired capability of the card
OBJECT-TYPE    
  INTEGER iop-frame-relay(1), iop-multi-service(2), iop-16meg-service(3), cp-basic(4), cp-30(5), cp-plus(8), cp-40(9), cp-50(10), iom-fcp(11)  

cardOperCapability 1.3.6.1.4.1.277.1.7.2.1.74
The actual capability of the card
OBJECT-TYPE    
  INTEGER iop-frame-relay(1), iop-multi-service(2), iop-16meg-service(3), cp-basic(4), cp-30(5), cp-plus(8), cp-40(9), cp-50(10), iom-fcp(11)  

cardISDNswtype 1.3.6.1.4.1.277.1.7.2.1.75
Specifies the ISDN central office switch type for the card.
OBJECT-TYPE    
  INTEGER att-4ess(1), att-5ess(2), dms100(3)  

cardCpuFgUtil 1.3.6.1.4.1.277.1.7.2.1.76
The CPU foreground utilization percentage for packet processing on this intelligent card.
OBJECT-TYPE    
  Gauge  

cardTrkProtState 1.3.6.1.4.1.277.1.7.2.1.77
Control for issue of Link Trunk Protocol request frames. If set to disabled, the issue of trunk protocol requests is blocked for all trunks on this card.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

cardISDNSigType 1.3.6.1.4.1.277.1.7.2.1.78
Specifies whether the ISDN Signalling type is Associated or Non-Facility Associated Signalling
OBJECT-TYPE    
  INTEGER no-nfas(1), nfas(2)  

cardISDNChanId 1.3.6.1.4.1.277.1.7.2.1.79
Specifies whether Channel ID assignment is performed by the central office switch or the 9000 - Exclusive (central office) Preferred (9000)
OBJECT-TYPE    
  INTEGER exclusive(1), preferred(2)  

cardTransmitClockConfig 1.3.6.1.4.1.277.1.7.2.1.80
The transmit clock source for timing section of the card
OBJECT-TYPE    
  INTEGER system-primary-clock(1), system-secondary-clock(2), system-primary-secondary-clock(3), free-running-clock(4), e1-G703sec10-clock(5), e1-network-clock(6)  

cardTransmitClockSwitchOver 1.3.6.1.4.1.277.1.7.2.1.81
Enable/disable automatic transmit clock source switch-over once a failed clock reference has recovered.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

cardTransmitClockStatus 1.3.6.1.4.1.277.1.7.2.1.82
The transmit clock PLL synchronization status of the card
OBJECT-TYPE    
  INTEGER in-synchronization(1), loss-of-synchronization(2)  

cardSystemPrimaryClockPortConfig 1.3.6.1.4.1.277.1.7.2.1.83
The port number (1-x) on the card that specifies the system primary clock source. A zero specifies no port
OBJECT-TYPE    
  INTEGER  

cardSystemPrimaryClockStatus 1.3.6.1.4.1.277.1.7.2.1.84
The system primary clock status as detected on the card. On the BIO, this refers to the Timing Module 1 clock status as detected by the BIO.
OBJECT-TYPE    
  INTEGER normal(1), failure(2)  

cardSystemSecondaryClockPortConfig 1.3.6.1.4.1.277.1.7.2.1.85
The port number (1 to x) on the card that specifies the system secondary clock source. A zero specifies no port
OBJECT-TYPE    
  INTEGER  

cardSystemSecondaryClockStatus 1.3.6.1.4.1.277.1.7.2.1.86
The system secondary clock status as detected on the card. On the BIO, this refers to the Timing Module 2 clock status as detected by the BIO.
OBJECT-TYPE    
  INTEGER normal(1), failure(2)  

cardInCells 1.3.6.1.4.1.277.1.7.2.1.87
The total number of cells received on this card.
OBJECT-TYPE    
  Counter  

cardInErrorCells 1.3.6.1.4.1.277.1.7.2.1.88
The total number of cells received on this card with HEC error.
OBJECT-TYPE    
  Counter  

cardInErrorVPIVCI 1.3.6.1.4.1.277.1.7.2.1.89
The total number of cells received with HEC invalid VPI, VCI.
OBJECT-TYPE    
  Counter  

cardOutCells 1.3.6.1.4.1.277.1.7.2.1.90
The total number of cells transmitted out of this card
OBJECT-TYPE    
  Counter  

cardOutDiscardCells 1.3.6.1.4.1.277.1.7.2.1.91
The total number of cells discarded due to congestion on this card
OBJECT-TYPE    
  Counter  

cardQOSQueueSize 1.3.6.1.4.1.277.1.7.2.1.92
The ATM QOS queue size (per cell) of each port on the card
OBJECT-TYPE    
  INTEGER cell-8K(1), cell-24K(2)  

cardLastErrorPort 1.3.6.1.4.1.277.1.7.2.1.93
The port number (1 to x) of the last cell with invalid cell header on the card
OBJECT-TYPE    
  INTEGER  

cardLastErrorVPI 1.3.6.1.4.1.277.1.7.2.1.94
The VPI of the last cell with invalid cell header on the card
OBJECT-TYPE    
  INTEGER  

cardLastErrorVCI 1.3.6.1.4.1.277.1.7.2.1.95
The VCI of the last cell with invalid cell header on the card
OBJECT-TYPE    
  INTEGER  

cardSystemPrimaryClockModeConfig 1.3.6.1.4.1.277.1.7.2.1.96
The system primary clock mode. PLCP is for DS3 port only
OBJECT-TYPE    
  INTEGER line-rate(1), plcp-mode(2)  

cardSystemSecondaryClockModeConfig 1.3.6.1.4.1.277.1.7.2.1.97
The system secondary clock mode. PLCP is for DS3 port only
OBJECT-TYPE    
  INTEGER line-rate(1), plcp-mode(2)  

cardNFBDEStatus 1.3.6.1.4.1.277.1.7.2.1.98
Non Fatal Background Diagnostic Error Status
OBJECT-TYPE    
  INTEGER cleared(1), not-cleared(2)  

cardProductCode 1.3.6.1.4.1.277.1.7.2.1.99
This card's product code.
OBJECT-TYPE    
  DisplayString  

cardMfgPN 1.3.6.1.4.1.277.1.7.2.1.100
This card's manufacturing part number.
OBJECT-TYPE    
  DisplayString  

cardTotalUpTime 1.3.6.1.4.1.277.1.7.2.1.101
This card's total accumulated up time, in hours.
OBJECT-TYPE    
  TimeTicks  

cardIOAType 1.3.6.1.4.1.277.1.7.2.1.102
The type of IOA attached to this card.
OBJECT-TYPE    
  INTEGER spa(1), toc3-4(2), tstm1-4(3), tds3-8(4), te3-8(5), toc3-smfir-n-4(6), toc3-smfir-r-4(7), toc3-mm-r-4(8), toc3-smflr-n-4(9), toc3-smflr-r-4(10), tstm1-smfir-n-4(11), tstm1-smfir-r-4(12), tstm1-mm-r-4(13), tstm1-smflr-n-4(14), tstm1-smflr-r-4(15), tds3-r-8(16), te3-r-8(17), hssi-n(18), hssi-r(19), toc12-smf-n-1(21), tads1-t1-n-8(22), tads1-t1-r-8(23), tads1-e1-75-n-8(24), tads1-e1-75-r-8(25), tads1-e1-120-n-8(26), tads1-e1-120-r-8(27), tads1-j2-75-n-8(28), tads1-j2-75-r-8(29), tads1-j2-120-n-8(30), tads1-j2-120-r-8(31), bCS-DS3-n-1(35), bCS-DS3-r-1(36), bIWU-OC3-mm-n-1(37), bIWU-OC3-smfir-n-1(38), toc3-stm1copper-n-4(39), toc3-stm1copper-r-4(40), spa-universal(32), nplus1-chassis(41), toc12-smflr-n-1(42), npa-universal(43), bIWU-OC3-bumm-1(44), bIWU-OC3-bumm-smfir-1(45), bIWU-OC3-trm-mm-1(46), bIWU-OC3-trm-smfir-1(47), uio-v35(48), uio-x21(49), bds1-e1-bnc-n-12(50), bds1-e1-bnc-r-12(51), bds1-e1-db15-n-12(52), bds1-e1-db15-r-12(53), bCS-E3-n-1(54), bCS-E3-r-1(55), bCP-1-m(56), bCP-1-o(57), be1-atm-75-n-12(58), be1-atm-75-r-12(59), be1-atm-120-n-12(60), be1-atm-120-r-12(61), bt1-atm-100-n-12(62), bt1-atm-100-r-12(63), bds1-e1-rj48h-n-12(64), bds1-e1-rj48h-r-12(65), gx550-backplane(66), cbx500-ether-n-4(67), cbx500-ds3-n-6(68), bstdx9000-ether-n-2(69), bio550-oc3-smfir(70), bio550-oc3-smflr(71), bio550-oc3-mmf(72), bio550-oc12-smfir(73), bio550-oc12-smflr(74), bio550-oc12-mmf(75)  

cardIOAHwRev 1.3.6.1.4.1.277.1.7.2.1.103
The attached IOA's hardware revision.
OBJECT-TYPE    
  DisplayString  

cardIOASerial 1.3.6.1.4.1.277.1.7.2.1.104
The attached IOA's serial number.
OBJECT-TYPE    
  DisplayString  

cardIOAProductCode 1.3.6.1.4.1.277.1.7.2.1.105
The attached IOA's product code.
OBJECT-TYPE    
  DisplayString  

cardIOAMfgPN 1.3.6.1.4.1.277.1.7.2.1.106
The attached IOA's manufacturing part number.
OBJECT-TYPE    
  DisplayString  

cardDS0Support 1.3.6.1.4.1.277.1.7.2.1.107
Some B-Stdx T1 boards do not support lpbk.
OBJECT-TYPE    
  INTEGER ds0-lpbk-not-supported(1), ds0-lpbk-supported(2)  

cardDiagParamId 1.3.6.1.4.1.277.1.7.2.1.108
Parameter identifier for internal diagnostics.
OBJECT-TYPE    
  INTEGER  

cardDiagParamValue 1.3.6.1.4.1.277.1.7.2.1.109
Value assigned to parameter specified by cardDiagParamId.
OBJECT-TYPE    
  INTEGER  

cardBulkStatsPeakCapability 1.3.6.1.4.1.277.1.7.2.1.110
Configures capability to collect peak 5-minute statistics. Capability change takes effect upon IOM reboot.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

cardBulkStatsTotalCapability 1.3.6.1.4.1.277.1.7.2.1.111
Configures capability to collect total statistics. Capability change takes effect upon IOM reboot.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

cardBulkStatsPeakEnable 1.3.6.1.4.1.277.1.7.2.1.112
Reflects the operational state of the peak 5-minute statistic collection on an IOM. For this setting to be enabled, the respective capability must be enabled.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

cardBulkStatsTotalEnable 1.3.6.1.4.1.277.1.7.2.1.113
Reflects the operational state of the total statistic collection on an IOM. For this setting to be enabled, the respective capability must be enabled.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

cardBulkStatsBaseCollectPeriod 1.3.6.1.4.1.277.1.7.2.1.114
Configures base collection period for bulk statistics on an IOM in minutes. Only the following values are allowed: 15, 20, 30, 60, 120, 180, 240, 360, 720, 1440. The default value is 60.
OBJECT-TYPE    
  INTEGER 15..1440  

cardNrtsHwRev 1.3.6.1.4.1.277.1.7.2.1.115
Hardware revision of the NRTS processor.
OBJECT-TYPE    
  INTEGER  

cardNrtsOutCellBufSize 1.3.6.1.4.1.277.1.7.2.1.116
The size of the NRTS output cell buffer.
OBJECT-TYPE    
  INTEGER  

cardNrtsOperState 1.3.6.1.4.1.277.1.7.2.1.117
The operational status of the NRTS processor.
OBJECT-TYPE    
  INTEGER absent(1), down(2), up(3)  

cardNrtsAdminState 1.3.6.1.4.1.277.1.7.2.1.118
The admin status of the NRTS processor.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

cardNrtsCcrmProtocolId 1.3.6.1.4.1.277.1.7.2.1.119
The protocol ID field for the CCRM cells. Must be different from the BCM protocol ID. Default is 6.
OBJECT-TYPE    
  INTEGER  

cardNrtsBcmProtocolId 1.3.6.1.4.1.277.1.7.2.1.120
The protocol ID field for the BCM cells. Must be different from the CCRM protocol ID. Default is 5.
OBJECT-TYPE    
  INTEGER  

cardNrtsRmGenInterval 1.3.6.1.4.1.277.1.7.2.1.121
The RM cell generation interval in ms. Minimum is 30, maximum is 250, default is 100.
OBJECT-TYPE    
  INTEGER  

cardNrtsIdleCktThresh 1.3.6.1.4.1.277.1.7.2.1.122
The number of RM cell generation intervals with no cell reception upon which the circuit is declared idle. Minimum is 1, maximum is 8, default is 8.
OBJECT-TYPE    
  INTEGER  

cardNrtsVbrNrtManage 1.3.6.1.4.1.277.1.7.2.1.123
Indicates whether VBR NRT traffic should be managed by the NRTS processor.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

cardNrtsIcrFact 1.3.6.1.4.1.277.1.7.2.1.124
A factor used to calculate the Initial Cell Rate for a circuit from its MCR and PCR.
OBJECT-TYPE    
  INTEGER  

cardNrtsMcastDiscardThresh 1.3.6.1.4.1.277.1.7.2.1.125
A NRTS discard threshold for the multicast circuits.
OBJECT-TYPE    
  INTEGER  

cardNrtsMcastDiscardCount 1.3.6.1.4.1.277.1.7.2.1.126
A NRTS discard counter for the multicast circuits.
OBJECT-TYPE    
  Counter  

cardAdminIOAType 1.3.6.1.4.1.277.1.7.2.1.127
The type of IOA attached to this card viewed from NMS.
OBJECT-TYPE    
  INTEGER spa(1), toc3-4(2), tstm1-4(3), tds3-8(4), te3-8(5), toc3-smfir-n-4(6), toc3-smfir-r-4(7), toc3-mm-r-4(8), toc3-smflr-n-4(9), toc3-smflr-r-4(10), tstm1-smfir-n-4(11), tstm1-smfir-r-4(12), tstm1-mm-r-4(13), tstm1-smflr-n-4(14), tstm1-smflr-r-4(15), tds3-r-8(16), te3-r-8(17), hssi-n(18), hssi-r(19), toc12-smf-n-1(21), tads1-t1-n-8(22), tads1-t1-r-8(23), tads1-e1-75-n-8(24), tads1-e1-75-r-8(25), tads1-e1-120-n-8(26), tads1-e1-120-r-8(27), tads1-j2-75-n-8(28), tads1-j2-75-r-8(29), tads1-j2-120-n-8(30), tads1-j2-120-r-8(31), bCS-DS3-n-1(35), bCS-DS3-r-1(36), bIWU-OC3-mm-n-1(37), bIWU-OC3-smfir-n-1(38), toc3-stm1copper-n-4(39), toc3-stm1copper-r-4(40), spa-universal(32), nplus1-chassis(41), toc12-smflr-n-1(42), npa-universal(43), bIWU-OC3-bumm-1(44), bIWU-OC3-bumm-smfir-1(45), bIWU-OC3-trm-mm-1(46), bIWU-OC3-trm-smfir-1(47), uio-v35(48), uio-x21(49), bds1-e1-bnc-n-12(50), bds1-e1-bnc-r-12(51), bds1-e1-db15-n-12(52), bds1-e1-db15-r-12(53), bCS-E3-n-1(54), bCS-E3-r-1(55), bCP-1-m(56), bCP-1-o(57), be1-atm-75-n-12(58), be1-atm-75-r-12(59), be1-atm-120-n-12(60), be1-atm-120-r-12(61), bt1-atm-100-n-12(62), bt1-atm-100-r-12(63), bds1-e1-rj48h-n-12(64), bds1-e1-rj48h-r-12(65), cbx500-ether-n-4(67), cbx500-ds3-n-6(68), bstdx9000-ether-n-2(69), bio550-oc3-smfir(70), bio550-oc3-smflr(71), bio550-oc3-mmf(72), bio550-oc12-smfir(73), bio550-oc12-smflr(74), bio550-oc12-mmf(75)  

cardNrtsMcastRate 1.3.6.1.4.1.277.1.7.2.1.128
The NRTS shaping rate for multicast circuits as a fraction of the line rate.
OBJECT-TYPE    
  INTEGER  

cardMonStatus 1.3.6.1.4.1.277.1.7.2.1.129
Set MON960 status, default(1) -- enable, 2 -- disable.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

cardImageSetA 1.3.6.1.4.1.277.1.7.2.1.130
The details of Image Set A. The elements of each image are space delimited and include Part Number, Revision, Size and Description. The details of each image are linefeed delimited.
OBJECT-TYPE    
  DisplayString  

cardImageSetB 1.3.6.1.4.1.277.1.7.2.1.131
The details of Image Set B. The elements of each image are space delimited and include Part Number, Revision, Size and Description. The details of each image are linefeed delimited.
OBJECT-TYPE    
  DisplayString  

cardMacAddress 1.3.6.1.4.1.277.1.7.2.1.132
ethernet MAC address of the card if there is an ethernet interface. Currently only CP cards may have ethernet. Cards without ethernet return 0 length octet string.
OBJECT-TYPE    
  DisplayString  

cardFlashRev 1.3.6.1.4.1.277.1.7.2.1.133
The boot flash rev number.
OBJECT-TYPE    
  DisplayString  

cardRequiredCapabilityBitmask 1.3.6.1.4.1.277.1.7.2.1.134
Bitmask indicating this cards' required capabilities based on configured features. A bit is set to one if the corresponding capability is required. This variable is a bitmask so only power-of-2 values can be assigned (1,2,4,8,16,etc.) .
OBJECT-TYPE    
  INTEGER aps-one-plus-one-support(1), holdover-support(2), vp-shaping(4), fe-capability(8)  

cardOperCapabilityBitmask 1.3.6.1.4.1.277.1.7.2.1.135
Bitmask indicating this cards' actual capabilities. A bit is set to one if the corresponding capability is supported. This variable is a bitmask so only power-of-2 values can be assigned (1,2,4,8,16,etc.).
OBJECT-TYPE    
  INTEGER aps-one-plus-one-supported(1), holdover-supported(2), vp-shaping(4), fe-capability(8)  

cardDslModule 1.3.6.1.4.1.277.1.7.2.1.136
This is for Dynamic Software Loadl You can type: ModuleName Version, ModuleName Version, ... to load modules.
OBJECT-TYPE    
  OCTET STRING  

cardIPTableSize 1.3.6.1.4.1.277.1.7.2.1.137
The maximum number of IP routing table entries supported by the card. If set to 0, routing table size is assumed unlimited.
OBJECT-TYPE    
  INTEGER  

cardIPTableState 1.3.6.1.4.1.277.1.7.2.1.138
State of the card's IP routing table. If set to marginal, the routing table maximum size has been exceeded. and all routes except management prefixes have been discarded.
OBJECT-TYPE    
  INTEGER normal(1), marginal(2)  

cardATMTcaInBufOverflowAlertPeriod 1.3.6.1.4.1.277.1.7.2.1.139
The atm tca ingress buffer overflow alert period (in min).
OBJECT-TYPE    
  INTEGER  

cardATMTcaInBufOverflowThresh 1.3.6.1.4.1.277.1.7.2.1.140
The atm tca ingress buffer overflow threshold.
OBJECT-TYPE    
  INTEGER  

cardATMTcaInInvalidVpiVciAlertPeriod 1.3.6.1.4.1.277.1.7.2.1.141
The atm tca ingress invalid vpi/vci alert period (in min).
OBJECT-TYPE    
  INTEGER  

cardATMTcaInInvalidVpiVciThresh 1.3.6.1.4.1.277.1.7.2.1.142
The atm tca ingress invalid vpi/vci threshold.
OBJECT-TYPE    
  INTEGER  

cardATMTcaInATMDCFullAlertPeriod 1.3.6.1.4.1.277.1.7.2.1.143
The atm tca ingress ATM DC full alert period (in min).
OBJECT-TYPE    
  INTEGER  

cardATMTcaInATMDCFullThresh 1.3.6.1.4.1.277.1.7.2.1.144
The atm tca ingress ATM DC full threshold.
OBJECT-TYPE    
  INTEGER  

cardATMTcaEnable 1.3.6.1.4.1.277.1.7.2.1.145
The atm tca enable/disable.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

cardATMTcaId 1.3.6.1.4.1.277.1.7.2.1.146
This object identifies the the most recently declared card ATM threshold crossing alert
OBJECT-TYPE    
  INTEGER ingressBufferOverfloeC(1), ingressInvalidVpiVciC(2), ingressATMDCFullC(3), ingressBufferMsbPaeC(4), ingressBufferHalfC(5), ingressBufferMsbPafC(6), egressCidLookupFailureC(7)  

cardATMTcaECidLookupFailureAlertPeriod 1.3.6.1.4.1.277.1.7.2.1.147
The atm tca ingress buffer overflow alert period (in min).
OBJECT-TYPE    
  INTEGER  

cardATMTcaECidLookupThresh 1.3.6.1.4.1.277.1.7.2.1.148
The atm tca ingress buffer overflow threshold.
OBJECT-TYPE    
  INTEGER  

cardATMTcaSPPearlOCbrFailureAlertPeriod 1.3.6.1.4.1.277.1.7.2.1.149
The atm tca sp pearl overflow CBR alert period (in min).
OBJECT-TYPE    
  INTEGER  

cardATMTcaSPPearlOCbrThresh 1.3.6.1.4.1.277.1.7.2.1.150
The atm tca sp pearl overflow CBR threshold.
OBJECT-TYPE    
  INTEGER  

cardATMTcaSPPearlOAbrFailureAlertPeriod 1.3.6.1.4.1.277.1.7.2.1.151
The atm tca sp pearl overflow ABR alert period (in min).
OBJECT-TYPE    
  INTEGER  

cardATMTcaSPPearlOAbrThresh 1.3.6.1.4.1.277.1.7.2.1.152
The atm tca sp pearl overflow ABR threshold.
OBJECT-TYPE    
  INTEGER  

cardATMTcaSPPearlOVbr1FailureAlertPeriod 1.3.6.1.4.1.277.1.7.2.1.153
The atm tca sp pearl overflow VBR1 alert period (in min).
OBJECT-TYPE    
  INTEGER  

cardATMTcaSPPearlOVbr1Thresh 1.3.6.1.4.1.277.1.7.2.1.154
The atm tca sp pearl overflow VBR1 threshold.
OBJECT-TYPE    
  INTEGER  

cardATMTcaSPPearlOVbr2FailureAlertPeriod 1.3.6.1.4.1.277.1.7.2.1.155
The atm tca sp pearl overflow VBR2 alert period (in min).
OBJECT-TYPE    
  INTEGER  

cardATMTcaSPPearlOVbr2Thresh 1.3.6.1.4.1.277.1.7.2.1.156
The atm tca sp pearl overflow VBR2 threshold.
OBJECT-TYPE    
  INTEGER  

cardATMTcaSPPearlGCbrFailureAlertPeriod 1.3.6.1.4.1.277.1.7.2.1.157
The atm tca sp pearl congestion CBR alert period (in min).
OBJECT-TYPE    
  INTEGER  

cardATMTcaSPPearlGCbrThresh 1.3.6.1.4.1.277.1.7.2.1.158
The atm tca sp pearl congestion CBR threshold.
OBJECT-TYPE    
  INTEGER  

cardATMTcaSPPearlGAbrFailureAlertPeriod 1.3.6.1.4.1.277.1.7.2.1.159
The atm tca sp pearl congestion ABR alert period (in min).
OBJECT-TYPE    
  INTEGER  

cardATMTcaSPPearlGAbrThresh 1.3.6.1.4.1.277.1.7.2.1.160
The atm tca sp pearl congestion ABR threshold.
OBJECT-TYPE    
  INTEGER  

cardATMTcaSPPearlGVbr1FailureAlertPeriod 1.3.6.1.4.1.277.1.7.2.1.161
The atm tca sp pearl congestion VBR1 alert period (in min).
OBJECT-TYPE    
  INTEGER  

cardATMTcaSPPearlGVbr1Thresh 1.3.6.1.4.1.277.1.7.2.1.162
The atm tca sp pearl congestion VBR1 threshold.
OBJECT-TYPE    
  INTEGER  

cardATMTcaSPPearlGVbr2FailureAlertPeriod 1.3.6.1.4.1.277.1.7.2.1.163
The atm tca sp pearl congestion VBR2 alert period (in min).
OBJECT-TYPE    
  INTEGER  

cardATMTcaSPPearlGVbr2Thresh 1.3.6.1.4.1.277.1.7.2.1.164
The atm tca sp pearl congestion VBR2 threshold.
OBJECT-TYPE    
  INTEGER  

cardATMTcaSPEnable 1.3.6.1.4.1.277.1.7.2.1.165
The atm tca SP enable/disable.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

cardSPEFCIEnable 1.3.6.1.4.1.277.1.7.2.1.166
The atm EFCI marking enable/disable.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

cardSPClpEnable 1.3.6.1.4.1.277.1.7.2.1.167
The atm CLP-1 enable/disable.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

spATMTcaId 1.3.6.1.4.1.277.1.7.2.1.168
This object identifies the the most recently declared sp ATM threshold crossing alert and first byte is used to indicate the switching port number. i.e. sp 1 has spBufferOverflowC, then the value is 0x1001
OBJECT-TYPE    
  INTEGER spBufferOverflowC1(1), spBufferOverflowC2(2), spBufferOverflowA1(3), spBufferOverflowA2(4), spBufferOverflowV11(5), spBufferOverflowV12(6), spBufferOverflowV21(7), spBufferOverflowV22(8), spBufferCongestionC1(9), spBufferCongestionC2(10), spBufferCongestionA1(11), spBufferCongestionA2(12), spBufferCongestionV11(13), spBufferCongestionV12(14), spBufferCongestionV21(15), spBufferCongestionV22(16)  

cardSubcardToRedundant 1.3.6.1.4.1.277.1.7.2.1.169
Commands the card to initiate an immediate protection switch on the identified subcard that it controls. This causes control to be switched from the active card to the standby card.
OBJECT-TYPE    
  CardTypes  

cardMemory5Usage 1.3.6.1.4.1.277.1.7.2.1.170
The bank5 memory utilization, in terms of free bytes, for CP Oynx card only.
OBJECT-TYPE    
  Gauge  

cardSF1OperStatus 1.3.6.1.4.1.277.1.7.2.1.171
The current status of Switch Fabric 1 (GX550).
OBJECT-TYPE    
  CardStatuses  

cardSF2OperStatus 1.3.6.1.4.1.277.1.7.2.1.172
The current status of Switch Fabric 2 (GX550).
OBJECT-TYPE    
  CardStatuses  

cardTM1OperStatus 1.3.6.1.4.1.277.1.7.2.1.173
The current status of Timing Module 1 (GX550).
OBJECT-TYPE    
  CardStatuses  

cardTM2OperStatus 1.3.6.1.4.1.277.1.7.2.1.174
The current status of Timing Module 2 (GX550).
OBJECT-TYPE    
  CardStatuses  

cardMemStartLog 1.3.6.1.4.1.277.1.7.2.1.175
Enable/Disable Memory log record, 1 -- enable, 0 -- disable.
OBJECT-TYPE    
  INTEGER enable(1)  

cardMemLogLevel 1.3.6.1.4.1.277.1.7.2.1.176
Set the Memory log level. Default 6
OBJECT-TYPE    
  INTEGER  

cardMemClrLog 1.3.6.1.4.1.277.1.7.2.1.177
Enable/Disable Clear Memory log, 1 -- clear, 0 (default) -- not clear.
OBJECT-TYPE    
  INTEGER enable(1)  

cardValidSubcards 1.3.6.1.4.1.277.1.7.2.1.178
The number of manageable subcards physically present in this card.
OBJECT-TYPE    
  INTEGER  

cardClp0CbrThreshold 1.3.6.1.4.1.277.1.7.2.1.179
The CLP 0 threshold for CBR queues in the card. Once queue length reaches this threshold, all CLP 1 cells are discarded until queue length falls below the threshold.
OBJECT-TYPE    
  INTEGER  

cardClp01CbrThreshold 1.3.6.1.4.1.277.1.7.2.1.180
The maximum length of CBR queues in the card. Once queue length reaches this threshold, all cells are discarded until queue length falls below this threshold.
OBJECT-TYPE    
  INTEGER  

cardClp0VbrRtThreshold 1.3.6.1.4.1.277.1.7.2.1.181
The CLP 0 threshold for VBR RT queues in the card. Once queue length reaches this threshold, all CLP 1 cells are discarded until queue length falls below the threshold.
OBJECT-TYPE    
  INTEGER  

cardClp01VbrRtThreshold 1.3.6.1.4.1.277.1.7.2.1.182
The maximum length of VBR-RT queues in the card. Once queue length reaches this threshold, all cells are discarded until queue length falls below this threshold.
OBJECT-TYPE    
  INTEGER  

cardClp0VbrNrtThreshold 1.3.6.1.4.1.277.1.7.2.1.183
The CLP 0 threshold for VBR NRT queues in the card. Once queue length reaches this threshold, all CLP 1 cells are discarded until queue length falls below the threshold.
OBJECT-TYPE    
  INTEGER  

cardClp01VbrNrtThreshold 1.3.6.1.4.1.277.1.7.2.1.184
The maximum length of VBR-NRT queues in the card. Once queue length reaches this threshold, all cells are discarded until queue length falls below this threshold.
OBJECT-TYPE    
  INTEGER  

cardClp0UAbrThreshold 1.3.6.1.4.1.277.1.7.2.1.185
The CLP 0 threshold for ABR/UBR queues in the card. Once queue length reaches this threshold, all CLP 1 cells are discarded until queue length falls below the threshold.
OBJECT-TYPE    
  INTEGER  

cardClp01UAbrThreshold 1.3.6.1.4.1.277.1.7.2.1.186
The maximum length of UBR/ABR queues in the card. Once queue length reaches this threshold, all cells are discarded until queue length falls below this threshold.
OBJECT-TYPE    
  INTEGER  

cardControlMessagesFromBus 1.3.6.1.4.1.277.1.7.2.1.187
The number of complete control Messages received over the Cell Bus for this card.
OBJECT-TYPE    
  Counter  

cardControlMessagesToBus 1.3.6.1.4.1.277.1.7.2.1.188
The number of complete control Messages transmitted by this card over the Cell Bus.
OBJECT-TYPE    
  Counter  

cardBTUsFromBus 1.3.6.1.4.1.277.1.7.2.1.189
The number of BTUs received by this card over the Cell Bus.
OBJECT-TYPE    
  Counter  

cardBTUsToBus 1.3.6.1.4.1.277.1.7.2.1.190
The number of BTUs transmitted by this card over the Cell Bus.
OBJECT-TYPE    
  Counter  

cardInvalidPvcBTUs 1.3.6.1.4.1.277.1.7.2.1.191
The number of BTUs received by this card over the Cell Bus with an invalid PVC identifier.
OBJECT-TYPE    
  Counter  

cardIncompleteFramesFromBus 1.3.6.1.4.1.277.1.7.2.1.192
The number of partial frames received by this card over the Cell Bus which were discarded due to missing BTUs.
OBJECT-TYPE    
  Counter  

cardBTUsBusErrors 1.3.6.1.4.1.277.1.7.2.1.193
The number of BTUs received by this card over the Cell Bus which were discarded due to errors.
OBJECT-TYPE    
  Counter  

cardBTUsNoResource 1.3.6.1.4.1.277.1.7.2.1.194
The number of BTUs received by this card over the Cell Bus which were discarded due to no free BTUs available to replace it.
OBJECT-TYPE    
  Counter  

cardInvalidPvcBTUsThreshold 1.3.6.1.4.1.277.1.7.2.1.195
Send trap if the number of BTUs received by this card over the Cell Bus with an invalid PVC identifier exceeds this in a one minute interval. Zero value implies no check.
OBJECT-TYPE    
  INTEGER  

cardIncompleteFramesFromBusThreshold 1.3.6.1.4.1.277.1.7.2.1.196
Send trap if the number of partial frames received by this card over the Cell Bus which were discarded due to missing BTUs exceeds this in a one minute interval. Zero value implies no check.
OBJECT-TYPE    
  INTEGER  

cardBTUsBusErrorThreshold 1.3.6.1.4.1.277.1.7.2.1.197
Send trap if the number of BTUs received by this card over the Cell Bus which were discarded due to errors exceeds this in a one minute interval. Zero value implies no check.
OBJECT-TYPE    
  INTEGER  

cardBTUsNoResourceThreshold 1.3.6.1.4.1.277.1.7.2.1.198
Send trap if the number of BTUs received by this card over the Cell Bus which were discarded due to no free BTUs available to replace it exceeds this in a one minute interval. Zero value implies no check.
OBJECT-TYPE    
  INTEGER  

cardFrameMemoryThreshold 1.3.6.1.4.1.277.1.7.2.1.199
The percentage of frame memory utilization on this card which will generate a trap. Zero value implies no check.
OBJECT-TYPE    
  INTEGER  

cardHoldQFrameMemory 1.3.6.1.4.1.277.1.7.2.1.200
The frame memory utilization, in terms of bytes, currently on the Hold Queues for this card.
OBJECT-TYPE    
  Counter  

cardTotalAAL5RxErrorCount 1.3.6.1.4.1.277.1.7.2.1.201
The total number of Rx errors detected by the AAL5 processor on this card.
OBJECT-TYPE    
  Counter  

cardOperMemSize 1.3.6.1.4.1.277.1.7.2.1.202
The total memory size on this card, in MB (1024 Kbytes).
OBJECT-TYPE    
  INTEGER  

ds1 1.3.6.1.4.1.277.1.8
OBJECT IDENTIFIER    

nodeSwDownloadFailed 1.3.6.1.4.1.277.1.8
This trap indicates that a software download failed.
TRAP-TYPE    
  nodeSwFilename  

dsx1ConfigTable 1.3.6.1.4.1.277.1.8.1
The DS1 Configuration table.
OBJECT-TYPE    
  SEQUENCE OF  
    Dsx1ConfigEntry

dsx1ConfigEntry 1.3.6.1.4.1.277.1.8.1.1
An entry in the DS1 Configuration table.
OBJECT-TYPE    
  Dsx1ConfigEntry  

dsx1SlotId 1.3.6.1.4.1.277.1.8.1.1.1
The slot number of the corresponding DS1.
OBJECT-TYPE    
  INTEGER  

dsx1PortId 1.3.6.1.4.1.277.1.8.1.1.2
The port number of the corresponding DS1 on the board.
OBJECT-TYPE    
  INTEGER  

dsx1TimeElapsed 1.3.6.1.4.1.277.1.8.1.1.3
The number of seconds that have elapsed since the beginning of the current error-measurement period.
OBJECT-TYPE    
  INTEGER 0..899  

dsx1ValidIntervals 1.3.6.1.4.1.277.1.8.1.1.4
The number of previous intervals for which valid data was collected. The value will be 96 unless the interface was brought on-line within the last 24 hours, in which case the value will be the number of complete 15 minute intervals the since interface has been online.
OBJECT-TYPE    
  INTEGER 0..96  

dsx1LineType 1.3.6.1.4.1.277.1.8.1.1.5
This variable indicates the variety of DS1 Line implementing this circuit. The type of circuit affects the number of bits per second that the circuit can reasonably carry, as well as the interpretation of the usage and error statistics. The values, in sequence, describe: TITLE: SPECIFICATION: dsx1ESF Extended SuperFrame DS1 dsx1D4 AT&T D4 format DS1 dsx1E1 CCITT Recommendation G.704 (Table 4a) dsx1E1-CRC CCITT Recommendation G.704 (Table 4b) dsxE1-MF G.704 (Table 4a) with TS16 multiframing enabled dsx1E1-CRC-MF G.704 (Table 4b) with TS16 multiframing enabled
OBJECT-TYPE    
  INTEGER other(1), dsx1ESF(2), dsx1D4(3), dsx1E1(4), dsx1E1-CRC(5), dsx1E1-MF(6), dsx1E1-CRC-MF(7)  

dsx1LineCoding 1.3.6.1.4.1.277.1.8.1.1.6
This variable describes the variety of Zero Code Suppression used on the link, which in turn affects a number of its characteristics. dsx1JBZS refers the Jammed Bit Zero Suppres- sion, in which the AT&T specification of at least one pulse every 8 bit periods is literal- ly implemented by forcing a pulse in bit 8 of each channel. Thus, only seven bits per chan- nel, or 1.344 Mbps, is available for data. dsx1B8ZS refers to the use of a specified pat- tern of normal bits and bipolar violations which are used to replace a sequence of eight zero bits. ANSI Clear Channels may use dsx1ZBTSI, or Zero Byte Time Slot Interchange. E1 links, with or without CRC, use dsx1HDB3 or dsx1AMI. dsx1AMI refers to a mode wherein no zero code suppression is present and the line encoding does not solve the problem directly. In this application, the higher layer must provide data which meets or exceeds the pulse density re- quirements, such as inverting HDLC data.
OBJECT-TYPE    
  INTEGER dsx1JBZS(1), dsx1B8ZS(2), dsx1HDB3(3), dsx1ZBTSI(4), dsx1AMI(5), other(6)  

dsx1SendCode 1.3.6.1.4.1.277.1.8.1.1.7
This variable indicates what type of code is being sent across the DS1 interface by the dev- ice. The values mean: dsx1SendNoCode sending looped or normal data dsx1SendLineCode sending a request for a line loopback dsx1SendPayloadCode sending a request for a payload loopback dsx1SendResetCode sending a loopback termination request dsx1SendQRS sending a Quasi-Random Signal (QRS) test pattern dsx1Send511Pattern sending a 511 bit fixed test pattern dsx1Send3in24Pattern sending a fixed test pattern of 3 bits set in 24 dsx1SendOtherTestPattern sending a test pattern other than those described by this object
OBJECT-TYPE    
  INTEGER dsx1SendNoCode(1), dsx1SendLineCode(2), dsx1SendPayloadCode(3), dsx1SendResetCode(4), dsx1SendQRS(5), dsx1Send511Pattern(6), dsx1Send3in24Pattern(7), dsx1SendOtherTestPattern(8)  

dsx1CircuitIdentifier 1.3.6.1.4.1.277.1.8.1.1.8
This variable contains the transmission vendor's circuit identifier, for the purpose of facilitating troubleshooting.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

dsx1LoopbackConfig 1.3.6.1.4.1.277.1.8.1.1.9
This variable represents the loopback confi- guration of the DS1 interface. Agents support- ing read/write access should return badValue in response to a requested loopback state that the interface does not support. The values mean: dsx1NoLoop Not in the loopback state. A device that is not capable of performing a loopback on the interface shall always return this as it's value. dsx1PayloadLoop The received signal at this interface is looped through the device. Typically the received signal is looped back for re- transmission after it has passed through the device's framing function. dsx1LineLoop The received signal at this interface does not go through the device (minimum pene- tration) but is looped back out. dsx1OtherLoop Loopbacks that are not defined here.
OBJECT-TYPE    
  INTEGER dsx1NoLoop(1), dsx1PayloadLoop(2), dsx1LineLoop(3), dsx1OtherLoop(4)  

dsx1LineStatus 1.3.6.1.4.1.277.1.8.1.1.10
This variable indicates the Line Status of the interface. It contains loopback, failure, re- ceived 'alarm' and transmitted 'alarm' infor- mation. The dsx1LineStatus is a bit map represented as a sum, therefore, it can represent multiple failures (alarms) and a LoopbackState simultaneously. dsx1NoAlarm should be set if and only if no other flag is set. If the dsx1LoopbackState bit is set, the loopback in ef- fect can be determined from the dsx1LoopbackConfig object. The various bit positions are: 1 dsx1NoAlarm No Alarm Present 2 dsx1RcvFarEndLOF Far end LOF (a.k.a., Yellow Alarm) 4 dsx1XmtFarEndLOF Near end sending LOF Indication 8 dsx1RcvAIS Far end sending AIS 16 dsx1XmtAIS Near end sending AIS 32 dsx1LossOfFrame Near end LOF (a.k.a., Red Alarm) 64 dsx1LossOfSignal Near end Loss Of Signal 128 dsx1LoopbackState Near end is looped 256 dsx1T16AIS E1 TS16 AIS 512 dsx1RcvFarEndLOMF Far End Sending TS16 LOMF 1024 dsx1XmtFarEndLOMF Near End Sending TS16 LOMF 2048 dsx1RcvTestCode Near End detects a test code 4096 dsx1OtherFailure any line status not defined here
OBJECT-TYPE    
  INTEGER 1..8191  

dsx1SignalMode 1.3.6.1.4.1.277.1.8.1.1.11
'none' indicates that no bits are reserved for signaling on this channel. 'robbedBit' indicates that T1 Robbed Bit Sig- naling is in use. 'bitOriented' indicates that E1 Channel Asso- ciated Signaling is in use. 'messageOriented' indicates that Common Chan- nel Signaling is in use either on channel 16 of an E1 link or channel 24 of a T1.
OBJECT-TYPE    
  INTEGER none(1), robbedBit(2), bitOriented(3), messageOriented(4)  

dsx1TransmitClockSource 1.3.6.1.4.1.277.1.8.1.1.12
The source of Tranmit Clock. 'loopTiming' indicates that the recovered re- ceive clock is used as the transmit clock. 'localTiming' indicates that a local clock source is used. 'throughTiming' indicates that recovered re- ceive clock from another interface is used as the transmit clock.
OBJECT-TYPE    
  INTEGER loopTiming(1), localTiming(2), throughTiming(3)  

dsx1Fdl 1.3.6.1.4.1.277.1.8.1.1.13
This bitmap describes the use of the facili- ties data link, and is the sum of the capabili- ties: 'other' indicates that a protocol other than one following is used. 'dsx1Ansi-T1-403' refers to the FDL exchange recommended by ANSI. 'dsx1Att-54016' refers to ESF FDL exchanges. 'dsx1Fdl-none' indicates that the device does not use the FDL.
OBJECT-TYPE    
  INTEGER other(1), dsx1Ansi-T1-403(2), dsx1Att-54016(4), dsx1Fdl-none(8)  

dsx1FdlVersion 1.3.6.1.4.1.277.1.8.1.1.14
The version of the Dallas FDL firmware
OBJECT-TYPE    
  INTEGER  

dsx1CurrentTable 1.3.6.1.4.1.277.1.8.2
The DS1 Current table.
OBJECT-TYPE    
  SEQUENCE OF  
    Dsx1CurrentEntry

dsx1CurrentEntry 1.3.6.1.4.1.277.1.8.2.1
An entry in the DS1 Current table.
OBJECT-TYPE    
  Dsx1CurrentEntry  

dsx1CurrentSlotId 1.3.6.1.4.1.277.1.8.2.1.1
The slot number of the corresponding DS1.
OBJECT-TYPE    
  INTEGER  

dsx1CurrentPortId 1.3.6.1.4.1.277.1.8.2.1.2
The port number of the corresponding DS1 on the board.
OBJECT-TYPE    
  INTEGER  

dsx1CurrentESs 1.3.6.1.4.1.277.1.8.2.1.3
The number of Errored Seconds, encountered by a DS1 interface in the current 15 minute inter- val.
OBJECT-TYPE    
  Gauge  

dsx1CurrentSESs 1.3.6.1.4.1.277.1.8.2.1.4
The number of Severely Errored Seconds encoun- tered by a DS1 interface in the current 15 minute interval.
OBJECT-TYPE    
  Gauge  

dsx1CurrentSEFSs 1.3.6.1.4.1.277.1.8.2.1.5
The number of Severely Errored Framing Seconds encountered by a DS1 interface in the current 15 minute interval.
OBJECT-TYPE    
  Gauge  

dsx1CurrentUASs 1.3.6.1.4.1.277.1.8.2.1.6
The number of Unavailable Seconds encountered by a DS1 interface in the current 15 minute in- terval.
OBJECT-TYPE    
  Gauge  

dsx1CurrentCSSs 1.3.6.1.4.1.277.1.8.2.1.7
The number of Controlled Slip Seconds encoun- tered by a DS1 interface in the current 15 minute interval.
OBJECT-TYPE    
  Gauge  

dsx1CurrentBESs 1.3.6.1.4.1.277.1.8.2.1.8
The number of Bursty Errored Seconds (BESs) encountered by a DS1 interface in the current 15 minute interval.
OBJECT-TYPE    
  Gauge  

dsx1IntervalTable 1.3.6.1.4.1.277.1.8.3
The DS1 Interval table.
OBJECT-TYPE    
  SEQUENCE OF  
    Dsx1IntervalEntry

dsx1IntervalEntry 1.3.6.1.4.1.277.1.8.3.1
An entry in the DS1 Interval table.
OBJECT-TYPE    
  Dsx1IntervalEntry  

dsx1IntervalSlotId 1.3.6.1.4.1.277.1.8.3.1.1
The slot number of the corresponding DS1.
OBJECT-TYPE    
  INTEGER  

dsx1IntervalPortId 1.3.6.1.4.1.277.1.8.3.1.2
The port number of the corresponding DS1 on the board.
OBJECT-TYPE    
  INTEGER  

dsx1IntervalNumber 1.3.6.1.4.1.277.1.8.3.1.3
A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes inter- val (assuming that all 96 intervals are valid).
OBJECT-TYPE    
  INTEGER 1..96  

dsx1IntervalESs 1.3.6.1.4.1.277.1.8.3.1.4
The number of Errored Seconds encountered by a DS1 interface in one of the previous 96, indi- vidual 15 minute, intervals.
OBJECT-TYPE    
  Gauge  

dsx1IntervalSESs 1.3.6.1.4.1.277.1.8.3.1.5
The number of Severely Errored Seconds encoun- tered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
OBJECT-TYPE    
  Gauge  

dsx1IntervalSEFSs 1.3.6.1.4.1.277.1.8.3.1.6
The number of Severely Errored Framing Seconds encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
OBJECT-TYPE    
  Gauge  

dsx1IntervalUASs 1.3.6.1.4.1.277.1.8.3.1.7
The number of Unavailable Seconds encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
OBJECT-TYPE    
  Gauge  

dsx1IntervalCSSs 1.3.6.1.4.1.277.1.8.3.1.8
The number of Controlled Slip Seconds encoun- tered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
OBJECT-TYPE    
  Gauge  

dsx1IntervalBESs 1.3.6.1.4.1.277.1.8.3.1.9
The number of Bursty Errored Seconds (BESs) encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
OBJECT-TYPE    
  Gauge  

dsx1TotalTable 1.3.6.1.4.1.277.1.8.4
The DS1 Total table. 24 hour interval.
OBJECT-TYPE    
  SEQUENCE OF  
    Dsx1TotalEntry

dsx1TotalEntry 1.3.6.1.4.1.277.1.8.4.1
An entry in the DS1 Total table.
OBJECT-TYPE    
  Dsx1TotalEntry  

dsx1TotalSlotId 1.3.6.1.4.1.277.1.8.4.1.1
The slot number of the corresponding DS1.
OBJECT-TYPE    
  INTEGER  

dsx1TotalPortId 1.3.6.1.4.1.277.1.8.4.1.2
The port number of the corresponding DS1 on the board.
OBJECT-TYPE    
  INTEGER  

dsx1TotalESs 1.3.6.1.4.1.277.1.8.4.1.3
The number of Errored Seconds encountered by a DS1 interface in the previous 24 hour interval
OBJECT-TYPE    
  Gauge  

dsx1TotalSESs 1.3.6.1.4.1.277.1.8.4.1.4
The number of Severely Errored Seconds encoun- tered by a DS1 interface in the previous 24 hour interval.
OBJECT-TYPE    
  Gauge  

dsx1TotalSEFSs 1.3.6.1.4.1.277.1.8.4.1.5
The number of Severely Errored Framing Seconds encountered by a DS1 interface in the previous 24 hour interval.
OBJECT-TYPE    
  Gauge  

dsx1TotalUASs 1.3.6.1.4.1.277.1.8.4.1.6
The number of Unavailable Seconds encountered by a DS1 interface in the previous 24 hour in- terval.
OBJECT-TYPE    
  Gauge  

dsx1TotalCSSs 1.3.6.1.4.1.277.1.8.4.1.7
The number of Controlled Slip Seconds encoun- tered by a DS1 interface in the previous 24 hour interval.
OBJECT-TYPE    
  Gauge  

dsx1TotalBESs 1.3.6.1.4.1.277.1.8.4.1.8
The number of Bursty Errored Seconds (BESs) encountered by a DS1 interface in the previous 24 hour interval.
OBJECT-TYPE    
  Gauge  

nodePrDownloadComplete 1.3.6.1.4.1.277.1.9
This trap indicates that a PRAM download was complete.
TRAP-TYPE    
  nodePrFilename  

nodePrDownloadFailed 1.3.6.1.4.1.277.1.10
This trap indicates that a PRAM download failed.
TRAP-TYPE    
  nodePrFilename  

nodeTracefull 1.3.6.1.4.1.277.1.11
This trap indicates that the node trace table was full and has been copied to a TFTP buffer awaiting to be xfered to the NMS.
TRAP-TYPE    

nodeDiagLogfull 1.3.6.1.4.1.277.1.12
This trap indicates that the diagnostic log table was full and has been copied to a TFTP buffer awaiting to be xfered to the NMS.
TRAP-TYPE    

nodeFlashMemErr 1.3.6.1.4.1.277.1.13
This trap indicates that a checksum or CRC-32 error occurred in Flash.
TRAP-TYPE    

nodePramErr 1.3.6.1.4.1.277.1.14
This trap indicates that a checksum error or battery problem occurred in PRAM.
TRAP-TYPE    

nodeRamErr 1.3.6.1.4.1.277.1.15
This trap indicates that an I/O error occurred in DRAM or SRAM.
TRAP-TYPE    

nodeInternalErr 1.3.6.1.4.1.277.1.16
This trap indicates that a fatal internal hardware or software error encountered and system needs to be re-booted.
TRAP-TYPE    

pportStatusChange 1.3.6.1.4.1.277.1.17
This trap indicates that the indicated physical port has changed state.
TRAP-TYPE    
  pportSlotId  
  pportId  
  pportOperStatus  
  pportLinkDownReason  

lportCongests 1.3.6.1.4.1.277.1.18
This trap indicates that the rate of entering severely and absolutely congested state on the indicated logical port has exceeded the threshold.
TRAP-TYPE    
  lportIfIndex  
  lportCongestRate  

trkStatusChange 1.3.6.1.4.1.277.1.19
This trap indicates that the trunk associated with the indicated logical port has changed state.
TRAP-TYPE    
  lportIfIndex  
  lportSlotId  
  lportPportId  
  lportId  
  lportTrkStatus  

cktDlciStatusChange 1.3.6.1.4.1.277.1.20
This trap indicates that the user-to-user PVC state has been changed for this virtual circuit. It has either been created or invalidated, or has toggled between the active and inactive states.
TRAP-TYPE    
  cktSrcIfIndex  
  cktSrcDlci  
  cktOperStatus  
  cktFailReason  
  cktFailNode  
  cktFailPort  

cktDlciReroute 1.3.6.1.4.1.277.1.21
This trap indicates that a PVC has been re-routed.
TRAP-TYPE    
  cktSrcIfIndex  
  cktSrcDlci  

pportInterfaceMismatch 1.3.6.1.4.1.277.1.22
This trap indicates the actual physical interface is different than the configured physical interface.
TRAP-TYPE    
  pportSlotId  
  pportId  
  pportAdminInterface  
  pportInterface  

lportErrorExceedThreshold 1.3.6.1.4.1.277.1.23
This trap indicates the frame errors per minute on this lport exceeded the threshold.
TRAP-TYPE    
  lportIfIndex  
  ifInErrors  

nodeErrorReport 1.3.6.1.4.1.277.1.24
A component in the switch discovered a non-fatal error condition.
TRAP-TYPE    
  nodeDiagNonFatalSource  
  nodeDiagNonFatalTime  
  nodeDiagNonFatalErrMajor  
  nodeDiagNonFatalErrMinor  
  nodeDiagNonFatalStr  

cktGrpStatusChange 1.3.6.1.4.1.277.1.25
Circuits on interfaces go up or down.
TRAP-TYPE    
  cardCktGroupTrap  

nodeUserLogin 1.3.6.1.4.1.277.1.26
An user has logged in STDX through either serial console or telnet.
TRAP-TYPE    
  nodeConsoleIndex  
  nodeUserName  
  nodeUserFrom  
  nodeConsoleUptime  

nodeUserLogout 1.3.6.1.4.1.277.1.27
An user has logged out.
TRAP-TYPE    
  nodeConsoleIndex  
  nodeUserName  
  nodeUserFrom  
  nodeConsoleUptime  

cardUp 1.3.6.1.4.1.277.1.28
This trap indicates that an intelligent card has transitioned to an ACTIVE state.
TRAP-TYPE    
  cardPhysicalSlotId  

cardDown 1.3.6.1.4.1.277.1.29
This trap indicates that an intelligent card has transitioned to a NON-ACTIVE state.
TRAP-TYPE    
  cardPhysicalSlotId  

lnkStatusChange 1.3.6.1.4.1.277.1.30
This trap indicates that the link status (Link protocol) associated with the indicated logical port has changed state.
TRAP-TYPE    
  lportIfIndex  
  lportSlotId  
  lportPportId  
  lportId  
  lportLinkStatus  

lnkSmdsHbpNaTca 1.3.6.1.4.1.277.1.31
This trap indicates that non-Ack count for SMDS DXI heartbeat poll exceedes the threshold. The non-Ack count is reset every 15 minutes.
TRAP-TYPE    
  lportIfIndex  
  lportSlotId  
  lportPportId  
  lportId  

lnkSmdsDiscardTca 1.3.6.1.4.1.277.1.32
This trap indicates that Total Discard packet count for SMDS packet exceedes the threshold. ( This trap has not been implemented in this release yet ).
TRAP-TYPE    
  lportIfIndex  
  lportSlotId  
  lportPportId  
  lportId  

cardRedundSwitchOver 1.3.6.1.4.1.277.1.33
This trap indicates that the card in the specified slot has shot its active partner and has become the active card of the pair.
TRAP-TYPE    
  cardPhysicalSlotId  

cardErrorReport 1.3.6.1.4.1.277.1.34
The specified card discovered a non-fatal error condition.
TRAP-TYPE    
  cardDiagNonFatalSource  
  cardDiagNonFatalTime  
  cardDiagNonFatalErrMajor  
  cardDiagNonFatalErrMinor  
  cardDiagNonFatalStr  
  cardPhysicalSlotId  

svcSetup 1.3.6.1.4.1.277.1.35
This trap is generated by the ingress switch whenever a Frame Relay Svc is setup or cleared. cktStatus indicates whether it is a setup or a clearing.
TRAP-TYPE    
  cktSrcIfIndex  
  cktSrcDlci  
  cktSvcCallingParty  
  cktSvcCalledParty  

svcClearing 1.3.6.1.4.1.277.1.36
Reserved for Frame Relay SVC.
TRAP-TYPE    

svcFailure 1.3.6.1.4.1.277.1.37
This trap is generated by the ingress switch whenever a Frame Relay svc setup fails. cktSvcCause contains the cause number.
TRAP-TYPE    
  cktSvcCallingParty  
  cktSvcCalledParty  
  cktSvcCause  

trkBuAttempt 1.3.6.1.4.1.277.1.38
This trap indicates that an attempt to establish the backup trunk associated with the indicated logical port is being made.
TRAP-TYPE    
  lportIfIndex  
  lportSlotId  
  lportPportId  
  lportId  

trkBuFailure 1.3.6.1.4.1.277.1.39
This trap indicates that the primary trunk associated with the indicated logical port has not been backed up or the backup trunk associated with the indicated logical port has not been restored. The reason for failure is provided. The lportBuFailReason indicates the trunk type as follows: lportBuFailReson Trunk Type buTrkNotDef primary trunk buTrkNotEstab backup trunk
TRAP-TYPE    
  lportIfIndex  
  lportSlotId  
  lportPportId  
  lportId  
  lportBuFailReason  

trkBuReleased 1.3.6.1.4.1.277.1.40
This trap indicates that the backup trunk associated with the indicated logical port has been released.
TRAP-TYPE    
  lportIfIndex  
  lportSlotId  
  lportPportId  
  lportId  

pportDS0LoopUpChange 1.3.6.1.4.1.277.1.41
This trap indicates one or more DS0's have gone into loopback.pportDS0LoopUpStatus reports the DS0's that have gone into loopback.
TRAP-TYPE    
  pportSlotId  
  pportId  
  pportDS0LoopUpStatus  

pportDS0LoopDownChange 1.3.6.1.4.1.277.1.42
This trap indicates one or more DS0's have gone out of loopback.pportDS0LoopDownStatus reports the DS0's that have gone out of loopback.
TRAP-TYPE    
  pportSlotId  
  pportId  
  pportDS0LoopDownStatus  

lportISDNCallRej 1.3.6.1.4.1.277.1.43
This trap indicates that a call has been rejected due either the inability to authenticate the call or lack of B-channel pool resources.
TRAP-TYPE    
  lportIfIndex  
  lportISDNCallRejCause  

pportdsx3LoopChange 1.3.6.1.4.1.277.1.44
This trap indicates when the DS3 or E3 has changed its current loopback state.
TRAP-TYPE    
  pportSlotId  
  pportId  
  pportdsx3LoopStatus  

pportds1LoopChange 1.3.6.1.4.1.277.1.45
This trap indicates when the DS1 has changed its current loopback state.
TRAP-TYPE    
  pportSlotId  
  pportId  
  pportds1LoopStatus  

pportExtClockBackup 1.3.6.1.4.1.277.1.46
This trap indicates that a pport has lost the external clock source and is switching over to the backup clock selected.
TRAP-TYPE    
  pportSlotId  
  pportId  
  pportSetClkBkup  

pportExtClockRestore 1.3.6.1.4.1.277.1.47
This trap indicates that external clock is recovered and the pport will switch back to external clock.
TRAP-TYPE    
  pportSlotId  
  pportId  

pportExtClkCapabilityMismatch 1.3.6.1.4.1.277.1.48
This trap indicates the port on this card (and the card itself) is not capable of running external clock.
TRAP-TYPE    
  pportSlotId  
  pportId  

nodeBillingUsageRecOvflWarning 1.3.6.1.4.1.277.1.50
Warning that a usage record counter-value overflow condition has occurred while aggregating usage data recently collected from one or more IOPs. An overflow condition exists when an attempt was made to update a usage record counter, but such an update would have overflowed the counter. In this case, the usage record is closed and a new one is opened, if there is sufficient space in the service's aggregated usage data store.
TRAP-TYPE    
  nodeBillingService  

nodeBillingUsageRecCrFailed 1.3.6.1.4.1.277.1.51
Notification that a usage record could not be created.
TRAP-TYPE    
  nodeBillingService  

nodeBillingStateChange 1.3.6.1.4.1.277.1.52
Notification that billing has been enabled or disabled on the switch. This trap is generated at switch boot or when the value of the nodeBilling object is modified.
TRAP-TYPE    
  nodeBillingService  
  nodeBilling  

lportBillingStateChange 1.3.6.1.4.1.277.1.53
Notification that billing has been enabled or disabled on a particular logical port. This trap is generated the value of the lportBilling is modified for a particular port; this trap IS NOT generated when the global nodeBilling is modified or when at switch boot.
TRAP-TYPE    
  nodeBillingService  
  lportBilling  
  lportIfIndex  
  lportSlotId  
  lportPportId  
  lportId  

nodeBillingSwAPCommsFailure 1.3.6.1.4.1.277.1.54
Notification that switch to Adjunct Processor communication has failed and that a usage file transfer has failed to complete.
TRAP-TYPE    
  nodeBillingAPAddress  

lportCBRLineDataError 1.3.6.1.4.1.277.1.57
This trap indicates the error state of the CBR lport.
TRAP-TYPE    
  lportIfIndex  
  lportSlotId  
  lportPportId  
  lportId  
  lportStarvation  
  lportRecOverflow  
  lportLossOfCellSequence  
  lportLossOfStructurePointer  

clkSourceSwitch 1.3.6.1.4.1.277.1.58
This trap indicates that the CBR port switched its clock method.
TRAP-TYPE    
  pportSlotId  
  pportId  
  pportCbrCurrentClockMode  

clkSourceFailure 1.3.6.1.4.1.277.1.59
This trap indicates that the clock generation unit switched between holdover mode and synchronization to reference clock.
TRAP-TYPE    
  pportSlotId  
  pportId  
  nodeRefclockActiveSrc  

lportSmdsSip3SaNotFoundTca 1.3.6.1.4.1.277.1.60
This trap indicates that the number of Sa Not Found violations exceeded the specified Smds pdu violation threshold for the logical port.
TRAP-TYPE    
  lportIfIndex  
  lportSlotId  
  lportPportId  
  lportId  

lportSmdsSip3SaDaOnSamePortTca 1.3.6.1.4.1.277.1.61
This trap indicates that the number of Sa Da On Same Port violations exceeded the specified Smds pdu violation threshold for the logical port.
TRAP-TYPE    
  lportIfIndex  
  lportSlotId  
  lportPportId  
  lportId  

lportSmdsSip3DstGaNotFoundTca 1.3.6.1.4.1.277.1.62
This trap indicates that the number of Dst Ga Not Found violations exceeded the specified Smds pdu violation threshold for the logical port.
TRAP-TYPE    
  lportIfIndex  
  lportSlotId  
  lportPportId  
  lportId  

lportSmdsSip3DstIaScrnFailTca 1.3.6.1.4.1.277.1.63
This trap indicates that the number of Dst Ia Scrn Fail violations exceeded the specified Smds pdu violation threshold for the logical port.
TRAP-TYPE    
  lportIfIndex  
  lportSlotId  
  lportPportId  
  lportId  

lportSmdsSip3SaValFailTca 1.3.6.1.4.1.277.1.64
This trap indicates that the number of Sa Val Fail violations exceeded the specified Smds pdu violation threshold for the logical port.
TRAP-TYPE    
  lportIfIndex  
  lportSlotId  
  lportPportId  
  lportId  

lportSmdsSip3DstIaNotFoundTca 1.3.6.1.4.1.277.1.65
This trap indicates that the number of Dst Ia Not Found violations exceeded the specified Smds pdu violation threshold for the logical port.
TRAP-TYPE    
  lportIfIndex  
  lportSlotId  
  lportPportId  
  lportId  

lportSmdsSip3SrcIaScrnFailTca 1.3.6.1.4.1.277.1.66
This trap indicates that the number of Src Ia Scrn Fail violations exceeded the specified Smds pdu violation threshold for the logical port.
TRAP-TYPE    
  lportIfIndex  
  lportSlotId  
  lportPportId  
  lportId  

lportSmdsSip3DstGaScrnFailTca 1.3.6.1.4.1.277.1.67
This trap indicates that the number of Dst Ga Scrn Fail violations exceeded the specified Smds pdu violation threshold for the logical port.
TRAP-TYPE    
  lportIfIndex  
  lportSlotId  
  lportPportId  
  lportId  

lportSmdsDxi2LinkIdInvalidTca 1.3.6.1.4.1.277.1.68
This trap indicates that the number of Link Id Invalid violations exceeded the specified Smds pdu violation threshold for the logical port.
TRAP-TYPE    
  lportIfIndex  
  lportSlotId  
  lportPportId  
  lportId  

nodePrimarySyncReferenceChange 1.3.6.1.4.1.277.1.69
Notification that the Primary Synchronization Reference operational state has changed.
TRAP-TYPE    
  nodePrimarySyncRefOperationalState  

nodeSecondarySyncReferenceChange 1.3.6.1.4.1.277.1.70
Notification that the Secondary Synchronization Reference operational state has changed.
TRAP-TYPE    
  nodeSecondarySyncRefOperationalState  

nodeExternalClockAChange 1.3.6.1.4.1.277.1.71
Notification that the External Reference Clock A operational state has changed.
TRAP-TYPE    
  nodeExternalClockAOperationalState  

nodeExternalClockBChange 1.3.6.1.4.1.277.1.72
Notification that the External Reference Clock B operational state has changed.
TRAP-TYPE    
  nodeExternalClockBOperationalState  

nodePortReferenceAChange 1.3.6.1.4.1.277.1.73
Notification that the Port Reference Clock A operational state has changed.
TRAP-TYPE    
  nodePortClockAOperationalState  

nodePortReferenceBChange 1.3.6.1.4.1.277.1.74
Notification that the Port Reference Clock B operational state has changed.
TRAP-TYPE    
  nodePortClockBOperationalState  

pportDS0InitiateLpbkFailure 1.3.6.1.4.1.277.1.75
This trap indicates that the DS0 requested to be set into far end loopback has failed to do so.
TRAP-TYPE    
  pportSlotId  
  pportId  
  pportDS0FarendDS0InLpbk  

pportDS0InitiateLpbkSuccess 1.3.6.1.4.1.277.1.76
This trap indicates that the DS0 requested to be set into far end loopback has succeeded.
TRAP-TYPE    
  pportSlotId  
  pportId  
  pportDS0FarendDS0InLpbk  

lportISDNIpAddrRej 1.3.6.1.4.1.277.1.77
This trap indicates that an Ip Address assignment failed.
TRAP-TYPE    
  lportIfIndex  
  lportISDNIpAddrAssignFail  

cktAtmStatusChange 1.3.6.1.4.1.277.1.78
This trap indicates that the user-to-user ATM PVC state has been changed for this virtual circuit. It has either been created or invalidated, or has toggled between the active and inactive states.
TRAP-TYPE    
  cktSrcIfIndex  
  cktAtmVPI  
  cktAtmVCI  
  cktOperStatus  
  cktFailReason  
  cktFailNode  
  cktFailPort  

cktAtmReroute 1.3.6.1.4.1.277.1.79
This trap indicates that an ATM PVC has been re-routed.
TRAP-TYPE    
  cktSrcIfIndex  
  cktAtmVPI  
  cktAtmVCI  

cardTransmitClockStatusChange 1.3.6.1.4.1.277.1.80
This trap indicates the IOM transmit clock synchronization status has chnaged.
TRAP-TYPE    
  cardPhysicalSlotId  
  cardTransmitClockStatus  

cardSystemPrimaryClockStatusChange 1.3.6.1.4.1.277.1.81
This trap indicates that the IOM system primary clock reference status has changed.
TRAP-TYPE    
  cardPhysicalSlotId  
  cardSystemPrimaryClockStatus  

cardSystemSecondaryClockStatusChange 1.3.6.1.4.1.277.1.82
This trap indicates that the IOM system primary clock reference status has changed.
TRAP-TYPE    
  cardPhysicalSlotId  
  cardSystemSecondaryClockStatus  

cascsmds 1.3.6.1.4.1.277.2
OBJECT IDENTIFIER    

smdsaddr 1.3.6.1.4.1.277.2.1
OBJECT IDENTIFIER    

smdsaddrTable 1.3.6.1.4.1.277.2.1.1
A list of smds adress entries.
OBJECT-TYPE    
  SEQUENCE OF  
    SmdsaddrEntry

smdsaddrEntry 1.3.6.1.4.1.277.2.1.1.1
An smds address and its associated information.
OBJECT-TYPE    
  SmdsaddrEntry  

smdsaddrAddr 1.3.6.1.4.1.277.2.1.1.1.1
SMDS address. The 4 most significant bits are the address type : 1100 for an individual address, 1110 for a group address. The following 4 bits are 0001. The following 5 bytes are the 10 digits number in BCD format. The following 16 bits are padded with 1's
OBJECT-TYPE    
  OCTET STRING  

smdsaddrType 1.3.6.1.4.1.277.2.1.1.1.2
SMDS address internal type.
OBJECT-TYPE    
  INTEGER local-individual-address(1), local-group-address(2), non-local-individual-address(3), non-local-group-address(4)  

smdsaddrId 1.3.6.1.4.1.277.2.1.1.1.3
smds address internal ID. Range from 1 to 192 for local individual addresses. Range from 193 to 704 for Alien individual addresses. Range from 1 to 64 for local group addresses. Range from 65 to 576 for alien group addresses.
OBJECT-TYPE    
  INTEGER  

smdsaddrIf 1.3.6.1.4.1.277.2.1.1.1.4
The interface to which this address is assigned.
OBJECT-TYPE    
  INTEGER  

smdsaddrParentGrpMap 1.3.6.1.4.1.277.2.1.1.1.5
The parent group bit map. The bit position of each bit in this bit map represent a parent group address ID. The most significant bit is corresponding to group address ID 1. This MIB object applies to a local individual address only.
OBJECT-TYPE    
  OCTET STRING  

smdsaddrParentScrnMap 1.3.6.1.4.1.277.2.1.1.1.6
This MIB object not applicable to switch software versions 03.99.00 and above. The parent screen bit map. The bit position of each bit in this bit map represent a parent screen ID. The most significant bit is corresponding to screen ID 1.
OBJECT-TYPE    
  OCTET STRING  

smdsaddrMemberAddrMap 1.3.6.1.4.1.277.2.1.1.1.7
The member individual address bit map. For set request, the first byte is the operation : 1 for deleting, 2 for adding. The following bytes are the bit map. The bit position of each bit in this bit map represent a member local individual address ID. The most significant bit is corresponding to local individual address ID 1. For get response, The whole string is the bit map.
OBJECT-TYPE    
  OCTET STRING  

smdsaddrAdminStatus 1.3.6.1.4.1.277.2.1.1.1.8
administration status
OBJECT-TYPE    
  INTEGER down(1), up(2)  

smdsaddrSlot 1.3.6.1.4.1.277.2.1.1.1.9
The Slot in which this address is assigned.
OBJECT-TYPE    
  INTEGER  

smdsaddrSsiIfNum 1.3.6.1.4.1.277.2.1.1.1.10
The SSI to which this address is associated.
OBJECT-TYPE    
  INTEGER  

namebinding 1.3.6.1.4.1.277.3
OBJECT IDENTIFIER    

namebindingTable 1.3.6.1.4.1.277.3.1
A table of name bindings to a set of logical ports.
OBJECT-TYPE    
  SEQUENCE OF  
    NamebindingEntry

namebindingEntry 1.3.6.1.4.1.277.3.1.1
The name binding entry contains objects relative to a name binding.
OBJECT-TYPE    
  NamebindingEntry  

nameType 1.3.6.1.4.1.277.3.1.1.1
The name type.
OBJECT-TYPE    
  INTEGER uninniladdr(1), e164(2), nsap(3), sni(4)  

nameName 1.3.6.1.4.1.277.3.1.1.2
A name of the type indicated by nameType.
OBJECT-TYPE    
  OCTET STRING  

namePrimary 1.3.6.1.4.1.277.3.1.1.3
The current binding type for this entry.
OBJECT-TYPE    
  INTEGER primary(1), backup(2)  

nameIfIndex 1.3.6.1.4.1.277.3.1.1.4
The interface number of the logical port for this binding.
OBJECT-TYPE    
  INTEGER  

nameNodeId 1.3.6.1.4.1.277.3.1.1.5
The identifier number of the node for this binding.
OBJECT-TYPE    
  INTEGER  

nameStatus 1.3.6.1.4.1.277.3.1.1.6
The status of the binding.
OBJECT-TYPE    
  INTEGER active(1), invalid(2)  

isdnaddr 1.3.6.1.4.1.277.4
OBJECT IDENTIFIER    

isdnAddrTable 1.3.6.1.4.1.277.4.1
A list of E.164 address entries.
OBJECT-TYPE    
  SEQUENCE OF  
    IsdnAddrEntry

isdnAddrEntry 1.3.6.1.4.1.277.4.1.1
Information about a single local E.164 address in the table. Setting this varible to 0 removes the entry.
OBJECT-TYPE    
  IsdnAddrEntry  

isdnAddrIf 1.3.6.1.4.1.277.4.1.1.1
The interface id of the logical port in question
OBJECT-TYPE    
  INTEGER  

isdnAddr 1.3.6.1.4.1.277.4.1.1.2
ISDN address. The actual E164 number. For example, ISDN address 15086922600 is stored as string 15086922600. Setting this value to a null string removes this entry.
OBJECT-TYPE    
  OCTET STRING  

isdnChanType 1.3.6.1.4.1.277.4.1.1.3
type of logical port 0 => isdn b-channel, 1 => sw56
OBJECT-TYPE    
  INTEGER  

isdnCallerIDTable 1.3.6.1.4.1.277.4.2
A list of valid caller ids
OBJECT-TYPE    
  SEQUENCE OF  
    IsdnCallerIDEntry

isdnCallerIDEntry 1.3.6.1.4.1.277.4.2.1
Information about a single valid caller id.
OBJECT-TYPE    
  IsdnCallerIDEntry  

isdnCallerIDIf 1.3.6.1.4.1.277.4.2.1.1
The interface id of the logical port in question
OBJECT-TYPE    
  INTEGER  

isdnCallerIDAddr 1.3.6.1.4.1.277.4.2.1.2
ISDN address. The actual E164 number. For example, ISDN address 15086922600 is stored as string 15086922600.
OBJECT-TYPE    
  OCTET STRING  

isdnCallerAdminStatus 1.3.6.1.4.1.277.4.2.1.3
administration status
OBJECT-TYPE    
  INTEGER add(1)  

cascsvc 1.3.6.1.4.1.277.5
OBJECT IDENTIFIER    

svcaddress 1.3.6.1.4.1.277.5.1
OBJECT IDENTIFIER    

svcNodePrefixTable 1.3.6.1.4.1.277.5.1.1
A table of prefixes associated with this node.
OBJECT-TYPE    
  SEQUENCE OF  
    SvcNodePrefixEntry

svcNodePrefixEntry 1.3.6.1.4.1.277.5.1.1.1
The node prefix entry contains objects relevant to SVC prefixes associated with the node.
OBJECT-TYPE    
  SvcNodePrefixEntry  

svcNodePrefixPrefix 1.3.6.1.4.1.277.5.1.1.1.1
A prefix associated with this node. E.164 prefixes are coded as 1-15 ASCII octets with no leading padding required. ATM endsystem prefixes are coded as 1-20 binary octets. Unused bits in the last octet must be set to 0.
OBJECT-TYPE    
  OCTET STRING SIZE(1..20)  

svcNodePrefixNumBits 1.3.6.1.4.1.277.5.1.1.1.2
The number of valid bits associated with this entry's prefix object. By default, this value will be 8 times the prefix object's octet string length.
OBJECT-TYPE    
  INTEGER 1..160  

svcNodePrefixNmbPlan 1.3.6.1.4.1.277.5.1.1.1.3
The numbering plan corresponding to this entry's prefix object.
OBJECT-TYPE    
  INTEGER e164(1), atm-endsystem(2), unknown(4)  

svcNodePrefixAdminStatus 1.3.6.1.4.1.277.5.1.1.1.4
The status of this entry.
OBJECT-TYPE    
  INTEGER configured(1), invalid(2)  

svcPrefixTable 1.3.6.1.4.1.277.5.1.2
A table of SVC address prefixes associated with ports on this node.
OBJECT-TYPE    
  SEQUENCE OF  
    SvcPrefixEntry

svcPrefixEntry 1.3.6.1.4.1.277.5.1.2.1
The prefix entry contains objects relevant to SVC prefixes associated with this port.
OBJECT-TYPE    
  SvcPrefixEntry  

svcPrefixIfIndex 1.3.6.1.4.1.277.5.1.2.1.1
The interface value of the corresponding MIB-II ifEntry.
OBJECT-TYPE    
  Index  

svcPrefixPrefix 1.3.6.1.4.1.277.5.1.2.1.2
A prefix associated with this port. E.164 prefixes are coded as 1-15 ASCII octets with no leading padding required. ATM endsystem prefixes are coded as 1-20 binary octets. Unused bits in the last octet must be set to 0. For ATM DCE ports, only, atm-endsystem prefixes with length 104 bits (13 octets) and all E.164 prefixes are eligible for ILMI address registration.
OBJECT-TYPE    
  OCTET STRING SIZE(1..20)  

svcPrefixNumBits 1.3.6.1.4.1.277.5.1.2.1.3
The number of valid bits associated with this entry's prefix object. By default, this value will be 8 times the prefix object's octet string length.
OBJECT-TYPE    
  INTEGER 1..160  

svcPrefixNmbPlan 1.3.6.1.4.1.277.5.1.2.1.4
The numbering plan corresponding to this entry's prefix object.
OBJECT-TYPE    
  INTEGER e164(1), atm-endsystem(2), unknown(4)  

svcPrefixAdminCost 1.3.6.1.4.1.277.5.1.2.1.5
This object is only relevant for ports connecting this network to another network and is used to represent the administrative cost of reaching destinations containing this entry's prefix value.
OBJECT-TYPE    
  INTEGER 0..65535  

svcPrefixLocalGatewayAddress 1.3.6.1.4.1.277.5.1.2.1.6
This object is only relevant for ports connecting this network to another network and is used to replace the calling party number when egress address translation is configured to the appropriate mode. E.164 addresses are coded as 1-15 ASCII octets Atm-endsystem addresses are coded as 20 octet binary addresses.
OBJECT-TYPE    
  OCTET STRING SIZE(0..20)  

svcPrefixLocalGatewayNmbPlan 1.3.6.1.4.1.277.5.1.2.1.7
The numbering plan corresponding to this entry's local gateway address object.
OBJECT-TYPE    
  INTEGER e164(1), atm-endsystem(2), unknown(4)  

svcPrefixRemoteGatewayAddress 1.3.6.1.4.1.277.5.1.2.1.8
This object is only relevant for ports connecting this network to another network and is used to replace the calling party number when egress address translation is configured to the appropriate mode. E.164 addresses are coded as 1-15 ASCII octets Atm-endsystem addresses are coded as 20 octet binary addresses.
OBJECT-TYPE    
  OCTET STRING SIZE(1..20)  

svcPrefixRemoteGatewayNmbPlan 1.3.6.1.4.1.277.5.1.2.1.9
The numbering plan corresponding to this entry's remote gateway address object.
OBJECT-TYPE    
  INTEGER e164(1), atm-endsystem(2), unknown(4)  

svcPrefixAdminStatus 1.3.6.1.4.1.277.5.1.2.1.10
The status of this entry.
OBJECT-TYPE    
  INTEGER configured(1), invalid(2), dynamic(3)  

svcAddrTable 1.3.6.1.4.1.277.5.1.3
A table of SVC addresses associated with with ports on this node.
OBJECT-TYPE    
  SEQUENCE OF  
    SvcAddrEntry

svcAddrEntry 1.3.6.1.4.1.277.5.1.3.1
The address entry contains objects relevant to SVC addresses associated with this port.
OBJECT-TYPE    
  SvcAddrEntry  

svcAddrIfIndex 1.3.6.1.4.1.277.5.1.3.1.1
The interface value of the corresponding MIB-II ifEntry.
OBJECT-TYPE    
  Index  

svcAddrAddress 1.3.6.1.4.1.277.5.1.3.1.2
An address associated with this port. E.164 addresses are coded as 1-15 ASCII octets. ATM-Endsystem addresses are coded as 20 binary octets.
OBJECT-TYPE    
  OCTET STRING SIZE(1..20)  

svcAddrNmbPlan 1.3.6.1.4.1.277.5.1.3.1.3
The numbering plan corresponding to this entry's address object.
OBJECT-TYPE    
  INTEGER e164(1), atm-endsystem(2), unknown(4)  

svcAddrAdminStatus 1.3.6.1.4.1.277.5.1.3.1.4
The status of this entry.
OBJECT-TYPE    
  INTEGER configured(1), invalid(2), dynamic(3)  

svcAtmUserPartTable 1.3.6.1.4.1.277.5.1.4
A table of partial SVC addresses associated with ports on this node, relevant only to ATM DTE ports for use in ILMI address registration.
OBJECT-TYPE    
  SEQUENCE OF  
    SvcAtmUserPartEntry

svcAtmUserPartEntry 1.3.6.1.4.1.277.5.1.4.1
The user part entry contains objects relevant to partial SVC addresses associated with ATM DTE ports on this node.
OBJECT-TYPE    
  SvcAtmUserPartEntry  

svcAtmUserPartIfIndex 1.3.6.1.4.1.277.5.1.4.1.1
The interface value of the corresponding MIB-II ifEntry.
OBJECT-TYPE    
  Index  

svcAtmUserPartUserPart 1.3.6.1.4.1.277.5.1.4.1.2
A partial ATM endsystem address associated with this ATM DTE port. It will be combined with ATM endsystem prefixes received from the peer DCE to form a full ATM endsystem address. This object is coded as 7 binary octets.
OBJECT-TYPE    
  OCTET STRING SIZE(7)  

svcAtmUserPartAdminStatus 1.3.6.1.4.1.277.5.1.4.1.3
The status of this entry.
OBJECT-TYPE    
  INTEGER configured(1), invalid(2)  

svcmgt 1.3.6.1.4.1.277.5.2
OBJECT IDENTIFIER    

svcConfigTable 1.3.6.1.4.1.277.5.2.1
A table of SVC configuration paramaters associated with logical ports. The number of entries is given by the value of ifNumber in MIB-II.
OBJECT-TYPE    
  SEQUENCE OF  
    SvcConfigEntry

svcConfigEntry 1.3.6.1.4.1.277.5.2.1.1
The SVC configuration entry contains objects relevant to SVC operation on a logical port.
OBJECT-TYPE    
  SvcConfigEntry  

svcConfigIfIndex 1.3.6.1.4.1.277.5.2.1.1.1
The ifIndex value of the corresponding ifEntry.
OBJECT-TYPE    
  Index  

svcConfigInitiateIdentStatsUpload 1.3.6.1.4.1.277.5.2.1.1.2
Setting this object initiates a TFTP upload of SVC identification statistics to the specified IP address. These statistics may be used to identify SVC's of interest on this port and to determine the keys for those SVC's so that further information may be obtained by accessing the circuit table.
OBJECT-TYPE    
  IpAddress  

svcConfigCgPtyInsertionMode 1.3.6.1.4.1.277.5.2.1.1.3
This object determines whether a statically configured address shall be inserted in the calling party address IE for calls entering the network at this port.
OBJECT-TYPE    
  INTEGER disabled(1), insert(2), replace(3)  

svcConfigCgPtyInsertionAddress 1.3.6.1.4.1.277.5.2.1.1.4
The calling party address to use in conjunction with the calling party insertion function. E.164 addresses are coded as 15 ASCII octets, utilizing leading ASCII '0' characters, as necessary. Atm-endsystem addresses are coded as 20 octet binary addresses.
OBJECT-TYPE    
  OCTET STRING SIZE(15..20)  

svcConfigCgPtyInsertionNmbPlan 1.3.6.1.4.1.277.5.2.1.1.5
The numbering plan corresponding to this entry's calling party insertion address object.
OBJECT-TYPE    
  INTEGER e164(1), atm-endsystem(2), unknown(4)  

svcConfigCgPtyScreenMode 1.3.6.1.4.1.277.5.2.1.1.6
The type of screening to perform on the calling party number for calls entering the network at this port. Screening will be conducted by performing a bit-wise (for prefixes) or byte-wise (for addresses) comparison of the calling party number with the appropriate prefix or address database(s), as configured.
OBJECT-TYPE    
  INTEGER node-prefix(1), port-prefix(2), node-prefix-or-port-prefix(3), address(4), node-prefix-or-address(5), port-prefix-or-address(6), node-prefix-or-port-prefix-or-address(7), disabled(255)  

svcConfigEgressAddrXlateMode 1.3.6.1.4.1.277.5.2.1.1.7
This object determines the type of address translation, if any to occur for calls exiting the network at this port. The tunnelling mode will screen the called address against the prefixes configured for this port. If no match is found, no action is taken. If a remote gateway address is configured for the matching prefix entry, the called party address will be tunnelled as a called subaddress and the configured remote gateway address will be inserted as the called party address. If a local gateway address is configured for the matching prefix entry, the calling party address, if present, will be tunnelled as a calling subaddress and the configured local gateway address, if present, will be inserted as the calling party. The replacement mode will operate as does the tunnelling mode, except the original called and calling party addresses will be discarded. The two translation modes are used for address interworking between networks using E.164 ATM Endsystem addresses and native ISDN E.164 addresses.
OBJECT-TYPE    
  INTEGER disabled(1), tunnel-when-called-party-matches-prefix(2), replace-when-called-party-matches-prefix(3), translate-e164-native-to-nsap(4), translate-e164-nsap-to-native(5)  

svcConfigIngressAddrXlateMode 1.3.6.1.4.1.277.5.2.1.1.8
This object determines the type of address translation, if any to occur for calls entering the network at this port. The tunnelling mode reverses the actions of egress tunnelling. If a called subaddress is present, it will replace the called party address, which will be discarded. If a calling subaddress is present, it will replace the calling party address, which will be discarded. The two translation modes are used for address interworking between networks using E.164 ATM Endsystem addresses and native ISDN E.164 addresses.
OBJECT-TYPE    
  INTEGER disabled(1), tunnel(2), translate-e164-native-to-nsap(4), translate-e164-nsap-to-native(5)  

svcConfigCgPtyPresentationMode 1.3.6.1.4.1.277.5.2.1.1.9
This object controls the circumstances under which the calling party number shall be presented at the egress port of the network.
OBJECT-TYPE    
  INTEGER user(1), never(2), always(3)  

svcAtmConfigTable 1.3.6.1.4.1.277.5.2.2
A table of ATM signalling paramaters associated with ATM logical ports. The maximum number of entries is given by the value of ifNumber in MIB-II.
OBJECT-TYPE    
  SEQUENCE OF  
    SvcAtmConfigEntry

svcAtmConfigEntry 1.3.6.1.4.1.277.5.2.2.1
The SVC ATM configuration entry contains objects relevant to the configuration and monitoring of ATM signalling on an ATM logical port.
OBJECT-TYPE    
  SvcAtmConfigEntry  

svcAtmConfigIfIndex 1.3.6.1.4.1.277.5.2.2.1.1
The ifIndex value of the corresponding ifEntry.
OBJECT-TYPE    
  Index  

svcAtmConfigAdminStatus 1.3.6.1.4.1.277.5.2.2.1.2
The configured state of the ATM signalling function for this port.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

svcAtmConfigOperStatus 1.3.6.1.4.1.277.5.2.2.1.3
The operational status of the signalling function on this port.
OBJECT-TYPE    
  INTEGER down(1), connecting(2), up(3)  

svcAtmConfigQ93bMaxRestart 1.3.6.1.4.1.277.5.2.2.1.4
The maximum number of unacknowledged restarts to send before declaring a signalling failure.
OBJECT-TYPE    
  INTEGER  

svcAtmConfigQ93bMaxStatEnq 1.3.6.1.4.1.277.5.2.2.1.5
The maximum number of unacknowledged status enquiries to send before issuing a restart.
OBJECT-TYPE    
  INTEGER  

svcAtmConfigQ93bT303 1.3.6.1.4.1.277.5.2.2.1.6
Protocol Timer T303, specified in milliseconds.
OBJECT-TYPE    
  INTEGER  

svcAtmConfigQ93bT308 1.3.6.1.4.1.277.5.2.2.1.7
Protocol Timer T308, specified in milliseconds.
OBJECT-TYPE    
  INTEGER  

svcAtmConfigQ93bT309 1.3.6.1.4.1.277.5.2.2.1.8
Protocol Timer T309, specified in milliseconds.
OBJECT-TYPE    
  INTEGER  

svcAtmConfigQ93bT310 1.3.6.1.4.1.277.5.2.2.1.9
Protocol Timer T310, specified in milliseconds.
OBJECT-TYPE    
  INTEGER  

svcAtmConfigQ93bT313 1.3.6.1.4.1.277.5.2.2.1.10
Protocol Timer T313, specified in milliseconds.
OBJECT-TYPE    
  INTEGER  

svcAtmConfigQ93bT316 1.3.6.1.4.1.277.5.2.2.1.11
Protocol Timer T316, specified in milliseconds.
OBJECT-TYPE    
  INTEGER  

svcAtmConfigQ93bT322 1.3.6.1.4.1.277.5.2.2.1.12
Protocol Timer T322, specified in milliseconds.
OBJECT-TYPE    
  INTEGER  

svcAtmConfigQ93bT398 1.3.6.1.4.1.277.5.2.2.1.13
Protocol Timer T398, specified in milliseconds.
OBJECT-TYPE    
  INTEGER  

svcAtmConfigQ93bT399 1.3.6.1.4.1.277.5.2.2.1.14
Protocol Timer T399, specified in milliseconds.
OBJECT-TYPE    
  INTEGER  

svcAtmConfigQ93bTotalConns 1.3.6.1.4.1.277.5.2.2.1.15
The total number of SVC's established on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQ93bActiveConns 1.3.6.1.4.1.277.5.2.2.1.16
The number of SVC's present on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQ93bLastCauseTx 1.3.6.1.4.1.277.5.2.2.1.17
The last transmitted cause code for this port.
OBJECT-TYPE    
  INTEGER unalloc-nmb(1), no-route-transnet(2), no-route-dest(3), vcc-unacceptable-30(10), normal-call-clr-31(16), user-busy(17), no-user-response(18), call-reject(21), nmb-changed(22), call-reject-clir(23), dest-out-of-order(27), invalid-nmb-format(28), response-stat-enq(30), normal-unspecified(31), req-vcc-unavailable(35), vcc-fail-31(36), rate-unavail-31(37), network-out-of-order(38), temp-fail(41), access-info-discard(43), no-vcc-available(45), resources-unavailable(47), qos-unavailable(49), rate-unavailable-30(51), b-cap-not-authorized(57), b-cap-unavailable(58), service-unavailable(63), b-cap-not-implemented(65), combination-unsupported(73), aal-params-unsupp-31(78), invalid-call-reference(81), no-channel(82), dest-incompatible(88), invalid-endpoint-ref(89), invalid-transit-net(91), too-many-add-pty-req(92), aal-params-unsupp-30(93), info-element-missing(96), msg-type-not-imp(97), info-element-not-imp(99), invalid-info-element(100), message-not-compatible(101), timer-recovery(102), invalid-message-len(104), protocol-error(111), optional-element-error(127)  

svcAtmConfigQ93bLastCauseRx 1.3.6.1.4.1.277.5.2.2.1.18
The last received cause code for this port.
OBJECT-TYPE    
  INTEGER unalloc-nmb(1), no-route-transnet(2), no-route-dest(3), vcc-unacceptable-30(10), normal-call-clr-31(16), user-busy(17), no-user-response(18), call-reject(21), nmb-changed(22), call-reject-clir(23), dest-out-of-order(27), invalid-nmb-format(28), response-stat-enq(30), normal-unspecified(31), req-vcc-unavailable(35), vcc-fail-31(36), rate-unavail-31(37), network-out-of-order(38), temp-fail(41), access-info-discard(43), no-vcc-available(45), resources-unavailable(47), qos-unavailable(49), rate-unavailable-30(51), b-cap-not-authorized(57), b-cap-unavailable(58), service-unavailable(63), b-cap-not-implemented(65), combination-unsupported(73), aal-params-unsupp-31(78), invalid-call-reference(81), no-channel(82), dest-incompatible(88), invalid-endpoint-ref(89), invalid-transit-net(91), too-many-add-pty-req(92), aal-params-unsupp-30(93), info-element-missing(96), msg-type-not-imp(97), info-element-not-imp(99), invalid-info-element(100), message-not-compatible(101), timer-recovery(102), invalid-message-len(104), protocol-error(111), optional-element-error(127)  

svcAtmConfigQ93bNumSetupPduTx 1.3.6.1.4.1.277.5.2.2.1.19
The number of setup PDU's transmitted on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQ93bNumSetupPduRx 1.3.6.1.4.1.277.5.2.2.1.20
The number of setup PDU's received on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQ93bNumCallProcPduTx 1.3.6.1.4.1.277.5.2.2.1.21
The number of call proceeding PDU's transmitted on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQ93bNumCallProcPduRx 1.3.6.1.4.1.277.5.2.2.1.22
The number of call proceeding PDU's received on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQ93bNumConnectPduTx 1.3.6.1.4.1.277.5.2.2.1.23
The number of connect PDU's transmitted on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQ93bNumConnectPduRx 1.3.6.1.4.1.277.5.2.2.1.24
The number of connect PDU's received on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQ93bNumConnectAckPduTx 1.3.6.1.4.1.277.5.2.2.1.25
The number of connect ack PDU's transmitted on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQ93bNumConnectAckPduRx 1.3.6.1.4.1.277.5.2.2.1.26
The number of connect ack PDU's received on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQ93bNumReleasePduTx 1.3.6.1.4.1.277.5.2.2.1.27
The number of release PDU's transmitted on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQ93bNumReleasePduRx 1.3.6.1.4.1.277.5.2.2.1.28
The number of release PDU's received on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQ93bNumReleaseCmpltPduTx 1.3.6.1.4.1.277.5.2.2.1.29
The number of release complete PDU's transmitted on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQ93bNumReleaseCmpltPduRx 1.3.6.1.4.1.277.5.2.2.1.30
The number of release complete PDU's received on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQ93bNumAddPtyPduTx 1.3.6.1.4.1.277.5.2.2.1.31
The number of add party PDU's transmitted on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQ93bNumAddPtyPduRx 1.3.6.1.4.1.277.5.2.2.1.32
The number of add party PDU's received on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQ93bNumAddPtyAckPduTx 1.3.6.1.4.1.277.5.2.2.1.33
The number of add party acknowledge PDU's transmitted on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQ93bNumAddPtyAckPduRx 1.3.6.1.4.1.277.5.2.2.1.34
The number of add party acknowledge PDU's received on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQ93bNumAddPtyRejPduTx 1.3.6.1.4.1.277.5.2.2.1.35
The number of add party reject PDU's transmitted on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQ93bNumAddPtyRejPduRx 1.3.6.1.4.1.277.5.2.2.1.36
The number of add party reject PDU's received on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQ93bNumDropPtyPduTx 1.3.6.1.4.1.277.5.2.2.1.37
The number of drop party PDU's transmitted on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQ93bNumDropPtyPduRx 1.3.6.1.4.1.277.5.2.2.1.38
The number of drop party PDU's received on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQ93bNumDropPtyAckPduTx 1.3.6.1.4.1.277.5.2.2.1.39
The number of drop party acknowledge PDU's transmitted on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQ93bNumDropPtyAckPduRx 1.3.6.1.4.1.277.5.2.2.1.40
The number of drop party acknowledge PDU's received on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQ93bNumStatusEnqPduTx 1.3.6.1.4.1.277.5.2.2.1.41
The number of status enquiry PDU's transmitted on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQ93bNumStatusEnqPduRx 1.3.6.1.4.1.277.5.2.2.1.42
The number of status enquiry PDU's received on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQ93bNumStatusPduTx 1.3.6.1.4.1.277.5.2.2.1.43
The number of status PDU's transmitted on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQ93bNumStatusPduRx 1.3.6.1.4.1.277.5.2.2.1.44
The number of status PDU's received on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQ93bNumRestartPduTx 1.3.6.1.4.1.277.5.2.2.1.45
The number of restart PDU's transmitted on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQ93bNumRestartPduRx 1.3.6.1.4.1.277.5.2.2.1.46
The number of restart PDU's received on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQ93bNumRestartAckPduTx 1.3.6.1.4.1.277.5.2.2.1.47
The number of restart acknowledge PDU's transmitted on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQ93bNumRestartAckPduRx 1.3.6.1.4.1.277.5.2.2.1.48
The number of restart acknowledge PDU's received on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQSaalMaxCC 1.3.6.1.4.1.277.5.2.2.1.49
The maximum number of unacknowledged transmitted control PDU's before declaring a loss of connection.
OBJECT-TYPE    
  INTEGER  

svcAtmConfigQSaalMaxPD 1.3.6.1.4.1.277.5.2.2.1.50
The maximum number of PDU's transmitted before a POLL PDU is transmitted.
OBJECT-TYPE    
  INTEGER  

svcAtmConfigQSaalMaxStat 1.3.6.1.4.1.277.5.2.2.1.51
The maximum number of list elements in a STAT PDU.
OBJECT-TYPE    
  INTEGER  

svcAtmConfigQSaalTPoll 1.3.6.1.4.1.277.5.2.2.1.52
The protocol timer corresponding to the polling function, specified in milliseconds.
OBJECT-TYPE    
  INTEGER  

svcAtmConfigQSaalTKeepalive 1.3.6.1.4.1.277.5.2.2.1.53
The protocol timer corresponding to the keepalive function, specified in milliseconds.
OBJECT-TYPE    
  INTEGER  

svcAtmConfigQSaalTNoResponse 1.3.6.1.4.1.277.5.2.2.1.54
The protocol timer corresponding to the response timeout function, specified in milliseconds.
OBJECT-TYPE    
  INTEGER  

svcAtmConfigQSaalTCC 1.3.6.1.4.1.277.5.2.2.1.55
The protocol timer corresponding to the transmission of control PDU's, specified in milliseconds.
OBJECT-TYPE    
  INTEGER  

svcAtmConfigQSaalTIdle 1.3.6.1.4.1.277.5.2.2.1.56
The protocol timer corresponding to the idle function for UNI 3.1, only, specified in milliseconds.
OBJECT-TYPE    
  INTEGER  

svcAtmConfigQSaalNumDiscardTx 1.3.6.1.4.1.277.5.2.2.1.57
The number of QSaal transmit discards on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQSaalNumDiscardRx 1.3.6.1.4.1.277.5.2.2.1.58
The number of QSaal receive discards on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQSaalNumErrorTx 1.3.6.1.4.1.277.5.2.2.1.59
The number of QSaal transmit errors on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQSaalNumErrorRx 1.3.6.1.4.1.277.5.2.2.1.60
The number of QSaal receive errors on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQSaalNumBgnPduTx 1.3.6.1.4.1.277.5.2.2.1.61
The number of begin PDU's transmitted on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQSaalNumBgnPduRx 1.3.6.1.4.1.277.5.2.2.1.62
The number of begin PDU's received on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQSaalNumBgakPduTx 1.3.6.1.4.1.277.5.2.2.1.63
The number of begin acknowledge PDU's transmitted on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQSaalNumBgakPduRx 1.3.6.1.4.1.277.5.2.2.1.64
The number of begin acknowledge PDU's received on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQSaalNumBgrejPduTx 1.3.6.1.4.1.277.5.2.2.1.65
The number of begin reject PDU's transmitted on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQSaalNumBgrejPduRx 1.3.6.1.4.1.277.5.2.2.1.66
The number of begin reject PDU's received on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQSaalNumEndPduTx 1.3.6.1.4.1.277.5.2.2.1.67
The number of end PDU's transmitted on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQSaalNumEndPduRx 1.3.6.1.4.1.277.5.2.2.1.68
The number of end PDU's received on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQSaalNumEndakPduTx 1.3.6.1.4.1.277.5.2.2.1.69
The number of end acknowledge PDU's transmitted on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQSaalNumEndakPduRx 1.3.6.1.4.1.277.5.2.2.1.70
The number of end acknowldge PDU's received on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQSaalNumRsPduTx 1.3.6.1.4.1.277.5.2.2.1.71
The number of resynchronization PDU's transmitted on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQSaalNumRsPduRx 1.3.6.1.4.1.277.5.2.2.1.72
The number of resynchronization PDU's received on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQSaalNumRsakPduTx 1.3.6.1.4.1.277.5.2.2.1.73
The number of resynchronization acknowledge PDU's transmitted on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQSaalNumRsakPduRx 1.3.6.1.4.1.277.5.2.2.1.74
The number of resynchronization acknowldge PDU's received on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQSaalNumErPduTx 1.3.6.1.4.1.277.5.2.2.1.75
The number of error recovery PDU's transmitted on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQSaalNumErPduRx 1.3.6.1.4.1.277.5.2.2.1.76
The number of errror recovery PDU's received on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQSaalNumErakPduTx 1.3.6.1.4.1.277.5.2.2.1.77
The number of error recovery acknowledge PDU's transmitted on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQSaalNumErakPduRx 1.3.6.1.4.1.277.5.2.2.1.78
The number of errror recovery acknowledge PDU's received on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQSaalNumSdPduTx 1.3.6.1.4.1.277.5.2.2.1.79
The number of sequenced data PDU's transmitted on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQSaalNumSdPduRx 1.3.6.1.4.1.277.5.2.2.1.80
The number of sequenced data PDU's received on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQSaalNumPollPduTx 1.3.6.1.4.1.277.5.2.2.1.81
The number of poll PDU's transmitted on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQSaalNumPollPduRx 1.3.6.1.4.1.277.5.2.2.1.82
The number of poll PDU's received on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQSaalNumStatPduTx 1.3.6.1.4.1.277.5.2.2.1.83
The number of status PDU's transmitted on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQSaalNumStatPduRx 1.3.6.1.4.1.277.5.2.2.1.84
The number of status PDU's received on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQSaalNumUstatPduTx 1.3.6.1.4.1.277.5.2.2.1.85
The number of unsolicited status PDU's transmitted on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQSaalNumUstatPduRx 1.3.6.1.4.1.277.5.2.2.1.86
The number of unsolicited status PDU's received on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQSaalNumUdPduTx 1.3.6.1.4.1.277.5.2.2.1.87
The number of unnumbered user data PDU's transmitted on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQSaalNumUdPduRx 1.3.6.1.4.1.277.5.2.2.1.88
The number of unnumbered user data PDU's received on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQSaalNumMdPduTx 1.3.6.1.4.1.277.5.2.2.1.89
The number of unnumbered management data PDU's transmitted on this port.
OBJECT-TYPE    
  Counter  

svcAtmConfigQSaalNumMdPduRx 1.3.6.1.4.1.277.5.2.2.1.90
The number of unnumbered management data PDU's received on this port.
OBJECT-TYPE    
  Counter  

svcAtmFailedCallTable 1.3.6.1.4.1.277.5.2.3
A table of objects describing the N most recent SVC failures per port, in FIFO order.
OBJECT-TYPE    
  SEQUENCE OF  
    SvcAtmFailedCallEntry

svcAtmFailedCallEntry 1.3.6.1.4.1.277.5.2.3.1
The failed call entry contains objects relevant to abnormal SVC call failures.
OBJECT-TYPE    
  SvcAtmFailedCallEntry  

svcAtmFailedCallIfIndex 1.3.6.1.4.1.277.5.2.3.1.1
The interface value of the corresponding MIB-II ifEntry for the port at which this call failure was declared.
OBJECT-TYPE    
  Index  

svcAtmFailedCallIndex 1.3.6.1.4.1.277.5.2.3.1.2
The instance number for this failed call at this port.
OBJECT-TYPE    
  INTEGER  

svcAtmFailedCallDirection 1.3.6.1.4.1.277.5.2.3.1.3
The direction of the failed call.
OBJECT-TYPE    
  INTEGER caller(1), callee(2)  

svcAtmFailedCallPduType 1.3.6.1.4.1.277.5.2.3.1.4
The Pdu Type containing the cause IE.
OBJECT-TYPE    
  INTEGER release(1), addPartyReject(2), dropParty(3)  

svcAtmFailedCallPduDirection 1.3.6.1.4.1.277.5.2.3.1.5
Whether the terminating PDU was transmitted or received on this port.
OBJECT-TYPE    
  INTEGER transmitted(1), received(2)  

svcAtmFailedCallCause 1.3.6.1.4.1.277.5.2.3.1.6
The failure cause contained in the cause IE.
OBJECT-TYPE    
  INTEGER unalloc-nmb(1), no-route-transnet(2), no-route-dest(3), vcc-unacceptable-30(10), normal-call-clr-31(16), user-busy(17), no-user-response(18), call-reject(21), nmb-changed(22), call-reject-clir(23), dest-out-of-order(27), invalid-nmb-format(28), response-stat-enq(30), normal-unspecified(31), req-vcc-unavailable(35), vcc-fail-31(36), rate-unavail-31(37), network-out-of-order(38), temp-fail(41), access-info-discard(43), no-vcc-available(45), resources-unavailable(47), qos-unavailable(49), rate-unavailable-30(51), b-cap-not-authorized(57), b-cap-unavailable(58), service-unavailable(63), b-cap-not-implemented(65), combination-unsupported(73), aal-params-unsupp-31(78), invalid-call-reference(81), no-channel(82), dest-incompatible(88), invalid-endpoint-ref(89), invalid-transit-net(91), too-many-add-pty-req(92), aal-params-unsupp-30(93), info-element-missing(96), msg-type-not-imp(97), info-element-not-imp(99), invalid-info-element(100), message-not-compatible(101), timer-recovery(102), invalid-message-len(104), protocol-error(111), optional-element-error(127)  

svcAtmFailedCallLocation 1.3.6.1.4.1.277.5.2.3.1.7
The failure location contained in the cause IE.
OBJECT-TYPE    
  INTEGER user(1), privNetServLocal(2), pubNetServLocal(3), transitNet(4), pubNetServRemote(5), privNetServRemote(6), intlNet(7), netBeyondInterwkPt(8)  

svcAtmFailedCallDiagnostic 1.3.6.1.4.1.277.5.2.3.1.8
The diagnostic information contained in the cause IE.
OBJECT-TYPE    
  OCTET STRING  

svcAtmFailedCallCreationTime 1.3.6.1.4.1.277.5.2.3.1.9
The sysUpTime when this call was initiated.
OBJECT-TYPE    
  TimeTicks  

svcAtmFailedCallTerminationTime 1.3.6.1.4.1.277.5.2.3.1.10
The sysUpTime when this call was terminated.
OBJECT-TYPE    
  TimeTicks  

svcAtmFailedCallFailureNodeId 1.3.6.1.4.1.277.5.2.3.1.11
The node which caused the SVC failure.
OBJECT-TYPE    
  INTEGER  

svcAtmFailedCallFailureIfIndex 1.3.6.1.4.1.277.5.2.3.1.12
The port on the failure node which caused the SVC failure.
OBJECT-TYPE    
  Index  

svcAtmFailedCallCallingParty 1.3.6.1.4.1.277.5.2.3.1.13
The calling party number for this failed call, if present.
OBJECT-TYPE    
  OCTET STRING  

svcAtmFailedCallCalledParty 1.3.6.1.4.1.277.5.2.3.1.14
The called party number for this failed call.
OBJECT-TYPE    
  OCTET STRING  

svcAtmFailedCallAtmTfdType 1.3.6.1.4.1.277.5.2.3.1.15
The combination of forward traffic parameters for this failed call.
OBJECT-TYPE    
  INTEGER pcr-0-01(1), pcr-0-01-tag(2), pcr-01-scr-0-mbs-0(3), pcr-01-scr-0-mbs-0-tag(4), pcr-01(5), pcr-01-scr-01-mbs-01(6), pcr-01-bestEffort(7), unknown(8)  

svcAtmFailedCallAtmTfdParam1 1.3.6.1.4.1.277.5.2.3.1.16
Forward traffic descriptor parameter 1 for this failed call.
OBJECT-TYPE    
  INTEGER  

svcAtmFailedCallAtmTfdParam2 1.3.6.1.4.1.277.5.2.3.1.17
Forward traffic descriptor parameter 2 for this failed call.
OBJECT-TYPE    
  INTEGER  

svcAtmFailedCallAtmTfdParam3 1.3.6.1.4.1.277.5.2.3.1.18
Forward traffic descriptor parameter 3 for this failed call.
OBJECT-TYPE    
  INTEGER  

svcAtmFailedCallAtmQosClass 1.3.6.1.4.1.277.5.2.3.1.19
Forward QOS class for this failed call.
OBJECT-TYPE    
  INTEGER  

svcAtmFailedCallAtmRTfdType 1.3.6.1.4.1.277.5.2.3.1.20
The combination of reverse traffic parameters for this failed call.
OBJECT-TYPE    
  INTEGER pcr-0-01(1), pcr-0-01-tag(2), pcr-01-scr-0-mbs-0(3), pcr-01-scr-0-mbs-0-tag(4), pcr-01(5), pcr-01-scr-01-mbs-01(6), pcr-01-bestEffort(7), unknown(8)  

svcAtmFailedCallAtmRTfdParam1 1.3.6.1.4.1.277.5.2.3.1.21
Reverse traffic descriptor parameter 1 for this failed call.
OBJECT-TYPE    
  INTEGER  

svcAtmFailedCallAtmRTfdParam2 1.3.6.1.4.1.277.5.2.3.1.22
Reverse traffic descriptor parameter 2 for this failed call.
OBJECT-TYPE    
  INTEGER  

svcAtmFailedCallAtmRTfdParam3 1.3.6.1.4.1.277.5.2.3.1.23
Reverse traffic descriptor parameter 3 for this failed call.
OBJECT-TYPE    
  INTEGER  

svcAtmFailedCallAtmRQoSClass 1.3.6.1.4.1.277.5.2.3.1.24
Reverse QOS class for this failed call.
OBJECT-TYPE    
  INTEGER  

svcAtmFailedCallBBearerClass 1.3.6.1.4.1.277.5.2.3.1.25
Broadband bearer class for this failed call.
OBJECT-TYPE    
  INTEGER class-A(1), class-C(3), class-X(16)  

svcAtmFailedCallBBearerTfcType 1.3.6.1.4.1.277.5.2.3.1.26
Broadband bearer traffic type for this failed call.
OBJECT-TYPE    
  INTEGER notIndicated(1), cbr(2), vbr(3)  

svcAtmFailedCallBBearerTmgRqmt 1.3.6.1.4.1.277.5.2.3.1.27
Broadband bearer timing requirement for this failed call.
OBJECT-TYPE    
  INTEGER notIndicated(1), required(2), not-required(3)  

svcAtmFailedCallBBearerUplaneCfg 1.3.6.1.4.1.277.5.2.3.1.28
Broadband bearer user plane configuration for this failed call.
OBJECT-TYPE    
  INTEGER point-point(1), point-multipoint(2)  

svcAtmFailedCallBBearerClippingSusc 1.3.6.1.4.1.277.5.2.3.1.29
Broadband bearer clipping susceptability for this failed call.
OBJECT-TYPE    
  INTEGER not-susceptible(1), susceptible(2)  

svcAtmFailedCallAdminStatus 1.3.6.1.4.1.277.5.2.3.1.30
All entries are initially invalid. Due to the FIFO nature of this table, once N entries have been created, all entries will always be valid.
OBJECT-TYPE    
  INTEGER valid(1), invalid(2)  

svcAtmFailedCall 1.3.6.1.4.1.277.5.55
Notification that one or more SVC call failures have been logged in the svcAtmFailedCallTable.
TRAP-TYPE    
  svcAtmFailedCallIfIndex  
  svcAtmFailedCallIndex  

svcAtmSigStatusChange 1.3.6.1.4.1.277.5.56
Notification that the status of the ATM signalling function has changed on the port.
TRAP-TYPE    
  svcAtmConfigIfIndex  
  svcAtmConfigOperStatus  

software 1.3.6.1.4.1.277.6
OBJECT IDENTIFIER    

swTable 1.3.6.1.4.1.277.6.1
A list of swEntry's. The number of entries is given by the value of swCardNumber
OBJECT-TYPE    
  SEQUENCE OF  
    SwEntry

swEntry 1.3.6.1.4.1.277.6.1.1
The software entry contains objects describing the software cards.
OBJECT-TYPE    
  SwEntry  

swLogicalSlotId 1.3.6.1.4.1.277.6.1.1.1
The logical slot number of this card. This is used as an index for the swTable. In redundant configurations, this can be the physical slot number of either redundant card. In non redundant configurations, this is the same as cardPhysicalSlotId.
OBJECT-TYPE    
  INTEGER  

swRedundState 1.3.6.1.4.1.277.6.1.1.2
The current redundancy state of this card.
OBJECT-TYPE    
  INTEGER active(1), standby(2)  

swRevision 1.3.6.1.4.1.277.6.1.1.3
The software revision number in the form (major.minor.maint.patch) where major == the major release number minor == the minor release number maint == a maintenance release based on major.minor patch == a patch release based on major.minor.maint
OBJECT-TYPE    
  DisplayString  

swBuildID 1.3.6.1.4.1.277.6.1.1.4
An identifier which uniquely identifies the software image within the scope of the release. The build ID is generated automatically through the build process and assigned to the software image during the final load generation.
OBJECT-TYPE    
  DisplayString  

swBuildDate 1.3.6.1.4.1.277.6.1.1.5
The date on which the software image was generated.
OBJECT-TYPE    
  DisplayString  

swBuildDescription 1.3.6.1.4.1.277.6.1.1.6
A general description of the release.
OBJECT-TYPE    
  DisplayString  

swCopyrightNotice 1.3.6.1.4.1.277.6.1.1.7
Legalese describing the Copyrights covering this software image.
OBJECT-TYPE    
  DisplayString  

swCapabilityMask 1.3.6.1.4.1.277.6.1.1.8
A 32-bit integer which bitmaps optional or additional features supported by this software release. For use by the NMS in determining capabilities of the software. The significance of this bitmap varies by release. For Cascade internal use.
OBJECT-TYPE    
  INTEGER  

swFeatureMask 1.3.6.1.4.1.277.6.1.1.9
A 32-bit integer which bitmaps optional or additional features supported by this software release. For use by the NMS in determining capabilities of the software. The significance of this bitmap varies by release. For Cascade internal use.
OBJECT-TYPE    
  INTEGER  

swPatchMask 1.3.6.1.4.1.277.6.1.1.10
A 32-bit integer which bitmaps incremental patches which have been applied to the software release. The significance of this bitmap varies by release. For Cascade internal use.
OBJECT-TYPE    
  INTEGER  

swBuildUserId 1.3.6.1.4.1.277.6.1.1.11
The user ID of the person responsible for generating the software image. For Cascade internal use.
OBJECT-TYPE    
  DisplayString  

swBuildView 1.3.6.1.4.1.277.6.1.1.12
Source control information for image generation. For Cascade internal use.
OBJECT-TYPE    
  DisplayString  

swBuildConfigSpec 1.3.6.1.4.1.277.6.1.1.13
Source control information for image generation. For Cascade internal use.
OBJECT-TYPE    
  DisplayString  

provserver 1.3.6.1.4.1.277.9
OBJECT IDENTIFIER    

nodeFileTransferReport 1.3.6.1.4.1.277.49
Reporting the outcome of a previous file transfer request. nodeFileTransferRequest specifies the request and nodeFileTransferStatus gives the outcome.
TRAP-TYPE    
  nodeFileTransferRequest  
  nodeFileTransferStatus  

Defined Objects

Index  
INTEGER    

AseEntry  
SEQUENCE    
  IpAddress as aseAddr  
  IpAddress as aseMask  
  IpAddress as aseDefaultGwAddr  
  INTEGER as aseMetricType  
  INTEGER as aseAdminStatus  
  Index as aseIfIndex  
  INTEGER as aseDlci  

NodeNMSEntry  
SEQUENCE    
  Index as nodeNMSIndex  
  IpAddress as nodeNMSIpAddr  

NodeFanEntry  
SEQUENCE    
  INTEGER as nodeFanIndex  
  INTEGER as nodeFanStatus  
  Gauge as nodeFanSpeed  

NodeConsoleEntry  
SEQUENCE    
  INTEGER as nodeConsoleIndex  
  OCTET STRING as nodeUserName  
  IpAddress as nodeUserFrom  
  INTEGER as nodeConsoleAccessMode  
  TimeTicks as nodeConsoleUptime  

NodeBillingEntry  
SEQUENCE    
  INTEGER as nodeBillingService  
  INTEGER as nodeBilling  
  TimeTicks as nodeBillingAggrPeriod  
  TimeTicks as nodeBillingCurAggrPeriodStart  
  TimeTicks as nodeBillingCurAggrPeriodEnd  
  TimeTicks as nodeBillingCollection  
  INTEGER as nodeBillingDailyProcessing  
  TimeTicks as nodeBillingDPTime  
  Counter as nodeBillingUsageRecOvflWarnings  
  Counter as nodeBillingTotalUsageRecOvflWarnings  
  Counter as nodeBillingBillableUsageEvents  
  Counter as nodeBillingNonBillableUsageEvents  
  Counter as nodeBillingUsageRecCreated  
  Counter as nodeBillingTotalUsageRecCreated  
  Counter as nodeBillingUsageRecCrFailures  
  Counter as nodeBillingTotalUsageRecCrFailures  
  Counter as nodeBillingUsageRecSent  
  Counter as nodeBillingTotalUsageRecSent  
  Counter as nodeBillingUsageDataStoreFull  
  Counter as nodeBillingTotalUsageDataStoreFull  
  INTEGER as nodeBillingAdminAction  

NodeRefclocksrcEntry  
SEQUENCE    
  INTEGER as nodeRefclocksrcIndex  
  INTEGER as nodeRefclocksrcPriority  
  INTEGER as nodeRefclocksrcType  
  INTEGER as nodeRefclocksrcSlotId  
  INTEGER as nodeRefclocksrcPportId  

NodeApplicationEntry  
SEQUENCE    
  Index as nodeApplicationIndex  
  DisplayString as nodeApplicationDescription  
  DisplayString as nodePrimaryVersion  
  DisplayString as nodeSecondaryVersion  

CardTypes  
INTEGER v35-6(1), ft1-1-24(2), fe1-1-30(3), uio-6(4), cp1(5), uio-8(6), ft1-4-24(7), fe1-4-30(8), ft3-1(9), fe3-1(10), hssi-2(11), dsx1-10(12), rs232-18(13), rs232-8(14), ut1-4-24(15), ue1-4-30(16), atmds3-1(17), atme3-1(18), pri-4(19), e1-pri-4(20), sft1-4-24(21), sut1-4-24(22), st1-pri-4(23), t1-atm(24), e1-atm(25), ads3-t3(26), ads3-e3(27), cbr-ds1-s-4(28), cbr-ds1-us-4(29), cbr-e1-s-4(30), cbr-e1-us-4(31), atmiwu-1(32), toc3-atm-4(33), tstm1-atm-4(34), sp-4(35), sp-8(36), atmcs-1(37), toc12-atm-1(38), tstm4-atm-1(39), ads1-t1(40), ads1-e1(41), ads1-j2(42), e1-12(43), bio1-4-16(44), bio1-oc3-4(45), bio1-oc12-1(46), bio1-oc12x4(47), bio1-oc48-1(48), np1(49), sf1(50), tm1(51), tfds3-t3-6(52), tfds3-e3-6(53), tfast-ether-4(54), fast-ether-2(55), ls-oc3-1(56), tcfds3-t3-6(57), tcfds3-e3-6(58), toc3-cfc-2(59), atmcs-e3-1(60), be1-atm-12(62), bt1-atm-12(63), bds3-1-0(64), gfether-4(65), gfds3-t3-6(66), gfds3-e3-6(67), gchn-ds3-4(68), g-server(69), sp-30(70), sp-40(71)    

CardStatuses  
INTEGER up(1), down(2), testing(3), maintenance(6), overtemp(7)    

CardEntry  
SEQUENCE    
  INTEGER as cardLogicalSlotId  
  INTEGER as cardPhysicalSlotId  
  CardTypes as cardAdminType  
  CardTypes as cardOperType  
  INTEGER as cardState  
  CardStatuses as cardAdminStatus  
  CardStatuses as cardOperStatus  
  INTEGER as cardDiagStatus  
  INTEGER as cardRedundConfig  
  INTEGER as cardRedundSlotMask  
  INTEGER as cardRedundActual  
  INTEGER as cardRedundState  
  TimeTicks as cardToRedundant  
  INTEGER as cardDiagNonFatalSource  
  TimeTicks as cardDiagNonFatalTime  
  INTEGER as cardDiagNonFatalErrMajor  
  INTEGER as cardDiagNonFatalErrMinor  
  DisplayString as cardDiagNonFatalStr  
  INTEGER as cardDiagFatalSource  
  TimeTicks as cardDiagFatalTime  
  INTEGER as cardDiagFatalErrMajor  
  INTEGER as cardDiagFatalErrMinor  
  DisplayString as cardDiagFatalStr  
  Counter as cardDiagFatalReboots  
  INTEGER as cardDiagFatalAddress  
  Counter as cardDiagBackgroundPasses  
  Counter as cardDiagBackgroundFailures  
  Counter as cardDiagBackgroundSuccesses  
  INTEGER as cardDiagLEDReset  
  INTEGER as cardDiagPowerExtensive  
  Gauge as cardCpuUtil  
  Gauge as cardMemoryUsage  
  Gauge as cardMaxVCs  
  Gauge as cardInUseVCs  
  Gauge as cardFreeVCs  
  Counter as cardInOctets  
  Counter as cardInPkts  
  Counter as cardOutOctets  
  Counter as cardOutPkts  
  TimeTicks as cardToWarmboot  
  TimeTicks as cardToColdboot  
  DisplayString as cardModel  
  DisplayString as cardSerial  
  DisplayString as cardSwRev  
  DisplayString as cardHwRev  
  DisplayString as cardEpromRev  
  DisplayString as cardName  
  OCTET STRING as cardCktGroupTrap  
  Counter as cardOutBtus  
  Counter as cardInGoodBtus  
  Counter as cardInErrorBtus  
  Counter as cardInNoVcBtus  
  Counter as cardInLinkDownBtus  
  Counter as cardInNoBufferBtus  
  Counter as cardInForwardBitBtus  
  INTEGER as cardDiagTestId  
  INTEGER as cardDiagTestRuns  
  INTEGER as cardDiagState  
  OCTET STRING as cardDiagOptionStr  
  Counter as cardDiagPasses  
  Counter as cardDiagFailures  
  DisplayString as cardDiagResultString  
  Gauge as cardFrameMemoryUtil  
  INTEGER as cardResetPram  
  Gauge as cardMemoryUtil  
  Gauge as cardFrameMemoryUsage  
  TimeTicks as cardUpTime  
  INTEGER as cardPramChecksum  
  INTEGER as cardPhysicalIndex  
  INTEGER as cardExternalClockRate  
  INTEGER as cardShootState  
  INTEGER as cardEraseAll  
  INTEGER as cardAdminCapability  
  INTEGER as cardOperCapability  
  INTEGER as cardISDNswtype  
  Gauge as cardCpuFgUtil  
  INTEGER as cardTrkProtState  
  INTEGER as cardISDNSigType  
  INTEGER as cardISDNChanId  
  INTEGER as cardTransmitClockConfig  
  INTEGER as cardTransmitClockSwitchOver  
  INTEGER as cardTransmitClockStatus  
  INTEGER as cardSystemPrimaryClockPortConfig  
  INTEGER as cardSystemPrimaryClockStatus  
  INTEGER as cardSystemSecondaryClockPortConfig  
  INTEGER as cardSystemSecondaryClockStatus  
  Counter as cardInCells  
  Counter as cardInErrorCells  
  Counter as cardInErrorVPIVCI  
  Counter as cardOutCells  
  Counter as cardOutDiscardCells  
  INTEGER as cardQOSQueueSize  
  INTEGER as cardLastErrorPort  
  INTEGER as cardLastErrorVPI  
  INTEGER as cardLastErrorVCI  
  INTEGER as cardSystemPrimaryClockModeConfig  
  INTEGER as cardSystemSecondaryClockModeConfig  
  INTEGER as cardNFBDEStatus  
  DisplayString as cardProductCode  
  DisplayString as cardMfgPN  
  TimeTicks as cardTotalUpTime  
  INTEGER as cardIOAType  
  DisplayString as cardIOAHwRev  
  DisplayString as cardIOASerial  
  DisplayString as cardIOAProductCode  
  DisplayString as cardIOAMfgPN  
  INTEGER as cardDS0Support  
  INTEGER as cardDiagParamId  
  INTEGER as cardDiagParamValue  
  INTEGER as cardBulkStatsPeakCapability  
  INTEGER as cardBulkStatsTotalCapability  
  INTEGER as cardBulkStatsPeakEnable  
  INTEGER as cardBulkStatsTotalEnable  
  INTEGER as cardBulkStatsBaseCollectPeriod  
  INTEGER as cardNrtsHwRev  
  INTEGER as cardNrtsOutCellBufSize  
  INTEGER as cardNrtsOperState  
  INTEGER as cardNrtsAdminState  
  INTEGER as cardNrtsCcrmProtocolId  
  INTEGER as cardNrtsBcmProtocolId  
  INTEGER as cardNrtsRmGenInterval  
  INTEGER as cardNrtsIdleCktThresh  
  INTEGER as cardNrtsVbrNrtManage  
  INTEGER as cardNrtsIcrFact  
  INTEGER as cardNrtsMcastDiscardThresh  
  Counter as cardNrtsMcastDiscardCount  
  INTEGER as cardAdminIOAType  
  INTEGER as cardNrtsMcastRate  
  INTEGER as cardMonStatus  
  DisplayString as cardImageSetA  
  DisplayString as cardImageSetB  
  DisplayString as cardMacAddress  
  DisplayString as cardFlashRev  
  INTEGER as cardRequiredCapabilityBitmask  
  INTEGER as cardOperCapabilityBitmask  
  OCTET STRING as cardDslModule  
  INTEGER as cardIPTableSize  
  INTEGER as cardIPTableState  
  INTEGER as cardATMTcaInBufOverflowAlertPeriod  
  INTEGER as cardATMTcaInBufOverflowThresh  
  INTEGER as cardATMTcaInInvalidVpiVciAlertPeriod  
  INTEGER as cardATMTcaInInvalidVpiVciThresh  
  INTEGER as cardATMTcaInATMDCFullAlertPeriod  
  INTEGER as cardATMTcaInATMDCFullThresh  
  INTEGER as cardATMTcaEnable  
  INTEGER as cardATMTcaId  
  INTEGER as cardATMTcaECidLookupFailureAlertPeriod  
  INTEGER as cardATMTcaECidLookupThresh  
  INTEGER as cardATMTcaSPPearlOCbrFailureAlertPeriod  
  INTEGER as cardATMTcaSPPearlOCbrThresh  
  INTEGER as cardATMTcaSPPearlOAbrFailureAlertPeriod  
  INTEGER as cardATMTcaSPPearlOAbrThresh  
  INTEGER as cardATMTcaSPPearlOVbr1FailureAlertPeriod  
  INTEGER as cardATMTcaSPPearlOVbr1Thresh  
  INTEGER as cardATMTcaSPPearlOVbr2FailureAlertPeriod  
  INTEGER as cardATMTcaSPPearlOVbr2Thresh  
  INTEGER as cardATMTcaSPPearlGCbrFailureAlertPeriod  
  INTEGER as cardATMTcaSPPearlGCbrThresh  
  INTEGER as cardATMTcaSPPearlGAbrFailureAlertPeriod  
  INTEGER as cardATMTcaSPPearlGAbrThresh  
  INTEGER as cardATMTcaSPPearlGVbr1FailureAlertPeriod  
  INTEGER as cardATMTcaSPPearlGVbr1Thresh  
  INTEGER as cardATMTcaSPPearlGVbr2FailureAlertPeriod  
  INTEGER as cardATMTcaSPPearlGVbr2Thresh  
  INTEGER as cardATMTcaSPEnable  
  INTEGER as cardSPEFCIEnable  
  INTEGER as cardSPClpEnable  
  INTEGER as spATMTcaId  
  CardTypes as cardSubcardToRedundant  
  Gauge as cardMemory5Usage  
  CardStatuses as cardSF1OperStatus  
  CardStatuses as cardSF2OperStatus  
  CardStatuses as cardTM1OperStatus  
  CardStatuses as cardTM2OperStatus  
  INTEGER as cardMemStartLog  
  INTEGER as cardMemLogLevel  
  INTEGER as cardMemClrLog  
  INTEGER as cardValidSubcards  
  INTEGER as cardClp0CbrThreshold  
  INTEGER as cardClp01CbrThreshold  
  INTEGER as cardClp0VbrRtThreshold  
  INTEGER as cardClp01VbrRtThreshold  
  INTEGER as cardClp0VbrNrtThreshold  
  INTEGER as cardClp01VbrNrtThreshold  
  INTEGER as cardClp0UAbrThreshold  
  INTEGER as cardClp01UAbrThreshold  
  Counter as cardControlMessagesFromBus  
  Counter as cardControlMessagesToBus  
  Counter as cardBTUsFromBus  
  Counter as cardBTUsToBus  
  Counter as cardInvalidPvcBTUs  
  Counter as cardIncompleteFramesFromBus  
  Counter as cardBTUsBusErrors  
  Counter as cardBTUsNoResource  
  INTEGER as cardInvalidPvcBTUsThreshold  
  INTEGER as cardIncompleteFramesFromBusThreshold  
  INTEGER as cardBTUsBusErrorThreshold  
  INTEGER as cardBTUsNoResourceThreshold  
  INTEGER as cardFrameMemoryThreshold  
  Counter as cardHoldQFrameMemory  
  Counter as cardTotalAAL5RxErrorCount  
  INTEGER as cardOperMemSize  

PportEntry  
SEQUENCE    
  INTEGER as pportSlotId  
  INTEGER as pportId  
  INTEGER as pportAdminType  
  INTEGER as pportNumLport  
  INTEGER as pportDataRate  
  INTEGER as pportType  
  INTEGER as pportRecvClock  
  INTEGER as pportXmitClock  
  INTEGER as pportAdminStatus  
  INTEGER as pportOperStatus  
  INTEGER as pportDs1LineType  
  INTEGER as pportDs1ZeroCoding  
  INTEGER as pportDs1LineBuildout  
  INTEGER as pportDiagTestId  
  INTEGER as pportDiagTestRuns  
  Counter as pportInOctets  
  Counter as pportInFrames  
  Counter as pportInDiscards  
  Counter as pportInErrors  
  Counter as pportOutOctets  
  Counter as pportOutFrames  
  Counter as pportOutDiscards  
  Counter as pportOutErrors  
  INTEGER as pportDiagState  
  OCTET STRING as pportDiagOptionStr  
  INTEGER as pportDiagPassCount  
  INTEGER as pportDiagFailCount  
  DisplayString as pportDiagResultStr  
  INTEGER as pportLinkDownReason  
  INTEGER as pportInterface  
  INTEGER as pportAdminInterface  
  INTEGER as pportCellScramble  
  INTEGER as pportCbitParity  
  INTEGER as pportMaxBufferSize  
  INTEGER as pportPeakCellRate0  
  INTEGER as pportPeakCellRate1  
  INTEGER as pportPeakCellRate2  
  INTEGER as pportPeakCellRate3  
  INTEGER as pportPeakCellRate4  
  INTEGER as pportPeakCellRate5  
  INTEGER as pportPeakCellRate6  
  INTEGER as pportPeakCellRate7  
  INTEGER as pportInCells  
  INTEGER as pportInErrorCells  
  INTEGER as pportOutCells  
  INTEGER as pportDs3LineBuildout  
  INTEGER as pportSetDS0LoopUp  
  INTEGER as pportSetDS0LoopDown  
  INTEGER as pportDS0LoopUpStatus  
  INTEGER as pportDS0LoopDownStatus  
  INTEGER as pportDS0LoopStatus  
  INTEGER as pportISDN  
  INTEGER as pportdsx3LoopbackConfig  
  INTEGER as pportdsx3SendCode  
  INTEGER as pportdsx3LoopStatus  
  INTEGER as pportdsx3FEACStatus  
  INTEGER as pportds1LoopbackConfig  
  INTEGER as pportds1SendCode  
  INTEGER as pportds1LoopStatus  
  INTEGER as pportSetClkBkup  
  INTEGER as pportAtmIdleWord  
  INTEGER as pportAtmDisCardMode  
  INTEGER as pportAtmLastUnconfiguredVpi  
  INTEGER as pportAtmLastUnconfiguredVci  
  Counter as pportAtmUnconfiguredCells  
  INTEGER as pportAtmNumBitsVCI  
  INTEGER as pportAtmNumBitsVPI  
  INTEGER as pportAtmInterfaceType  
  INTEGER as pportSonetSDHLoopbackConfig  
  INTEGER as pportSonetSDHLoopStatus  
  Counter as pportOutDiscardsCell  
  INTEGER as pportAtmPlcp  
  INTEGER as pportCbrTargetClockMode  
  INTEGER as pportCbrCurrentClockMode  
  INTEGER as pportClockMasterChannel  
  INTEGER as pportFibreType  
  INTEGER as pportLaserStatus  
  INTEGER as pportMaxActiveVpiBits  
  INTEGER as pportBipErrorsThresh  
  Counter as pportBipSectionErrors  
  Counter as pportBipLineErrors  
  Counter as pportBipPathErrors  
  Counter as pportFebeErrors  
  Counter as pportHcsErrors  
  Counter as pportHcsSevereErrors  
  Counter as pportCongestedReceivedCells  
  Counter as pportCongestedTransmittedCells  
  Counter as pportAtmLayerErroredReceivedCells  
  Counter as pportAtmLayerErroredTransmittedCells  
  INTEGER as pportDS0BitStuff  
  INTEGER as pportDS0BitErrorCount  
  INTEGER as pportDS0BitErrorFreeSeconds  
  INTEGER as pportDS0BitErroredSeconds  
  INTEGER as pportDS0MidspanRepeaters  
  INTEGER as pportDS0TestPatternSync  
  INTEGER as pportDS0InjectBitError  
  INTEGER as pportDS0FarendLpbkType  
  INTEGER as pportDS0LpbkMode  
  INTEGER as pportDS0SwitchLpbkStart  
  INTEGER as pportDS0SwitchLpbkEnd  
  INTEGER as pportDS0FarendDS0InLpbk  
  INTEGER as pportDS0SendTestTraffic  
  INTEGER as pportOc3LoopConfig  
  INTEGER as pportOc3LoopStatus  
  IpAddress as pportISDNIpBaseAddr  
  INTEGER as pportSonetSTM1Scramble  
  INTEGER as pportEFCIMarking  
  INTEGER as pportAtmQOSTransmitMode  
  INTEGER as pportHECMode  
  OCTET STRING as pportISDNChannelStatus  
  INTEGER as pportds1FarEndLoopStatus  
  INTEGER as pportds1FDLControl  
  INTEGER as pportds1FDLPrmXmit  
  INTEGER as pportds1FDLPidXmit  
  OCTET STRING as pportds1FDLXmitPid  
  OCTET STRING as pportds1FDLRcvPid  
  OCTET STRING as pportds1FDLRcvTsid  
  INTEGER as pportSonetSDHFramingMode  
  INTEGER as pportds1InbandLoopType  
  INTEGER as pportESFDataLinkStatus  
  INTEGER as pportPMTcaId  
  INTEGER as pportBchanTimerValue  
  Counter as pportAAL5CRC32Error  
  Counter as pportAAL5CPIError  
  Counter as pportAAL5LengthError  
  Counter as pportAAL5ReassemblyTimerError  
  Counter as pportAAL5MaxNrSegError  
  INTEGER as pportRedundancyArch  
  INTEGER as pportAPSadminDir  
  INTEGER as pportAPSlineType  
  INTEGER as pportAPSrevertiveMode  
  INTEGER as pportAPSpairedSlotId  
  INTEGER as pportAPSpairedPportId  
  INTEGER as pportAPSsfBerThresh  
  INTEGER as pportAPSsdBerThresh  
  INTEGER as pportAPSwtrPeriod  
  INTEGER as pportAPSprotectionLineState  
  INTEGER as pportAPSxCommand  
  INTEGER as pportAPSconfigStatus  
  INTEGER as pportAPSOperRxStatus  
  INTEGER as pportBertPattern  
  INTEGER as pportBertUserBytes  
  INTEGER as pportBertErrorRate  
  INTEGER as pportBertCommand  
  INTEGER as pportBertStatus  
  Gauge as pportBertBitCount  
  Gauge as pportBertErrorCount  
  INTEGER as pportds1FELoopbackControl  
  DisplayString as pportFT1DS0s  
  INTEGER as pportIMUXCnt  
  INTEGER as pportds1PMConfigThresh  
  INTEGER as pportIdleCellType  
  INTEGER as pportATMTcaInHECErrorUAlertPeriod  
  INTEGER as pportATMTcaInHECErrorUThresh  
  INTEGER as pportATMTcaEBufOverflowCBRAlertPeriod  
  INTEGER as pportATMTcaEBufOverflowCBRThresh  
  INTEGER as pportATMTcaEBufOverflowABRAlertPeriod  
  INTEGER as pportATMTcaEBufOverflowABRThresh  
  INTEGER as pportATMTcaEBufOverflowVBR1AlertPeriod  
  INTEGER as pportATMTcaEBufOverflowVBR1Thresh  
  INTEGER as pportATMTcaEBufOverflowVBR2AlertPeriod  
  INTEGER as pportATMTcaEBufOverflowVBR2Thresh  
  INTEGER as pportATMTcaInFramerFIFOOverflowAlertPeriod  
  INTEGER as pportATMTcaInFramerFIFOOverflowThresh  
  INTEGER as pportATMTcaELookupFailureAlertPeriod  
  INTEGER as pportATMTcaELookupFailureThresh  
  INTEGER as pportATMTcaEnable  
  INTEGER as pportATMTcaId  
  OCTET STRING as pportFethAdminMacAddr  
  OCTET STRING as pportFethOperMacAddr  
  INTEGER as pportConfigAlarmSoakTime  
  INTEGER as pportConfigAlarmClearTime  
  INTEGER as pportFethPortCapability  
  INTEGER as pportVpshapingDiscardCellCount  

PportTrafficShaperEntry  
SEQUENCE    
  INTEGER as pportTrafficShaperIndex  
  INTEGER as pportTrafficShaperPriority  
  INTEGER as pportTrafficShaperCellRatioDividend  
  INTEGER as pportTrafficShaperCellRatioDivisor  
  INTEGER as pportTrafficShaperPeak  
  INTEGER as pportTrafficShaperCredit  

LportEntry  
SEQUENCE    
  Index as lportIfIndex  
  INTEGER as lportSlotId  
  INTEGER as lportPportId  
  INTEGER as lportId  
  INTEGER as lportLink  
  INTEGER as lportProtocol  
  INTEGER as lportSignal  
  OCTET STRING as lportFt1Ds0s  
  INTEGER as lportGlobalDlci  
  INTEGER as lportDlcmiStd  
  INTEGER as lportDlciAddrFmt  
  INTEGER as lportDlciAddrLen  
  INTEGER as lportMaxFramesize  
  INTEGER as lportDceVerifTimer  
  INTEGER as lportDceErrorThresh  
  INTEGER as lportDceEventCount  
  INTEGER as lportDteErrorThresh  
  INTEGER as lportDteEventCount  
  INTEGER as lportDtePollTimer  
  INTEGER as lportDteFullCounter  
  INTEGER as lportDteMulticast  
  IpAddress as lportTrkRnode  
  INTEGER as lportTrkRlport  
  INTEGER as lportCongestState  
  INTEGER as lportQP1Len  
  INTEGER as lportQP2Len  
  INTEGER as lportQP3Len  
  INTEGER as lportQP4Len  
  TimeTicks as lportErrTime  
  INTEGER as lportErrType  
  OCTET STRING as lportErrData  
  INTEGER as lportDiagTestId  
  INTEGER as lportDiagTestRuns  
  INTEGER as lportDataRate  
  INTEGER as lportTrkStatus  
  INTEGER as lportSevCongests  
  INTEGER as lportAbsCongests  
  INTEGER as lportTrkOverhead  
  INTEGER as lportTrkUtil  
  INTEGER as lportVAvailbw  
  TimeTicks as lportTrkLastTimeChange  
  INTEGER as lportCongestRate  
  INTEGER as lportCongestRateThresh  
  INTEGER as lportDiagState  
  OCTET STRING as lportDiagOptionStr  
  INTEGER as lportDiagPassCount  
  INTEGER as lportDiagFailCount  
  DisplayString as lportDiagResultStr  
  INTEGER as lportDs0BitStuff  
  INTEGER as lportErrorThreshold  
  INTEGER as lportUnsyncBandwidth  
  Counter as lportDTEInStatusFrames  
  Counter as lportDTEInFullStatusFrames  
  Counter as lportDTEInAsyncStatusFrames  
  Counter as lportDTEInErrorFrames  
  Counter as lportDTEOutPollFrames  
  Counter as lportDTEPollErrorCounts  
  Counter as lportDTEFailCounts  
  INTEGER as lportDTEFailReason  
  INTEGER as lportDTEOperStatus  
  Counter as lportDCEInPollFrames  
  Counter as lportDCEInErrorFrames  
  Counter as lportDCEOutStatusFrames  
  Counter as lportDCEOutFullStatusFrames  
  Counter as lportDCEOutAsyncStatusFrames  
  Counter as lportDCEPollErrorCounts  
  Counter as lportDCEFailCounts  
  INTEGER as lportDCEFailReason  
  INTEGER as lportDCEOperStatus  
  INTEGER as lportDCEOperDlcmiStd  
  Counter as lportLMIInErrorFrames  
  INTEGER as lportDCEnN4  
  INTEGER as lportDCEnT3  
  INTEGER as lportXmitLatencyThreshold  
  INTEGER as lportXmitRefillPriority0Percentage  
  INTEGER as lportXmitRefillPriority1Percentage  
  INTEGER as lportXmitRefillPriority2Percentage  
  INTEGER as lportXmitRefillPriority3Percentage  
  INTEGER as lportXmitDiscardLow  
  INTEGER as lportSevereThreshold  
  INTEGER as lportMildThreshold  
  INTEGER as lportTrkKeepAliveTimer  
  INTEGER as lportTrkKeepAliveErrorThreshold  
  INTEGER as lportIgCutThruStatus  
  INTEGER as lportEgCutThruStatus  
  INTEGER as lportEgCutThruThresh  
  INTEGER as lportFrameRelayTrkEnable  
  INTEGER as lportSmdsSsiIf  
  INTEGER as lportSmdsSsiSlot  
  INTEGER as lportSmdsScrnId  
  INTEGER as lportSmdsIaScrnOp  
  INTEGER as lportSmdsGaScrnOp  
  OCTET STRING as lportSmdsIaScrnMap  
  OCTET STRING as lportSmdsGaScrnMap  
  OCTET STRING as lportSmdsTrkAddr  
  INTEGER as lportSmdsCrc  
  INTEGER as lportSmdsCpePoll  
  INTEGER as lportSmdsPduCheck  
  Counter as lportSmdsCntOutFrDxi2HbPolls  
  Counter as lportSmdsCntOutByteDxi2HbPolls  
  Counter as lportSmdsCntInFrDxi2HbPolls  
  Counter as lportSmdsCntInByteDxi2HbPolls  
  Counter as lportSmdsCntOutFrSip3s  
  Counter as lportSmdsCntOutByteSip3s  
  Counter as lportSmdsCntInFrSip3s  
  Counter as lportSmdsCntInByteSip3s  
  Counter as lportSmdsCntDxi2LinkIdInvalids  
  Counter as lportSmdsCntDxi2StationIdInvalids  
  Counter as lportSmdsCntDxi2CrInvalids  
  Counter as lportSmdsCntDxi2AeInvalids  
  Counter as lportSmdsCntDxi2CtrlInvalids  
  Counter as lportSmdsCntDxi2FrameSizeErrors  
  Counter as lportSmdsCntSip3RsvdInvalids  
  Counter as lportSmdsCntSip3BetagMismatchs  
  Counter as lportSmdsCntSip3BasizeIncorrects  
  Counter as lportSmdsCntSip3BasizeInvalids  
  Counter as lportSmdsCntSip3DaTypeInvalids  
  Counter as lportSmdsCntSip3DaInvalids  
  Counter as lportSmdsCntSip3SaTypeInvalids  
  Counter as lportSmdsCntSip3SaInvalids  
  Counter as lportSmdsCntSip3BasizeMismatchs  
  Counter as lportSmdsCntSip3HeLenInvalids  
  Counter as lportSmdsCntSip3HeVersionInvalids  
  Counter as lportSmdsCntSip3HeCarrierInvalids  
  Counter as lportSmdsCntSip3Crc32Errors  
  Counter as lportSmdsCntSip3TRsvdInvalids  
  Counter as lportSmdsCntSaNotFounds  
  Counter as lportSmdsCntSaValidationFails  
  Counter as lportSmdsCntSaDaOnSamePorts  
  Counter as lportSmdsCntDaSsiMismacths  
  Counter as lportSmdsCntSsiProvisionErrors  
  Counter as lportSmdsCntDstIaNotFounds  
  Counter as lportSmdsCntDstGaNotFounds  
  Counter as lportSmdsCntSrcIaScrnFails  
  Counter as lportSmdsCntDstIaScrnFails  
  Counter as lportSmdsCntDstGaScrnFails  
  Counter as lportSmdsTotalDiscards  
  INTEGER as lportSmdsSsiNode  
  INTEGER as lportBilling  
  INTEGER as lportSmdsReserved144  
  INTEGER as lportLinkStatus  
  INTEGER as lportLMIDelay  
  INTEGER as lportCRC  
  OCTET STRING as lportSmdsMulticastGa  
  IpAddress as lportSmdsMulticastIpAddr  
  INTEGER as lportAtmVPI  
  INTEGER as lportAtmVCI  
  INTEGER as lportPeakCellRateindex  
  INTEGER as lportSustCellRate  
  INTEGER as lportBurstTolerance  
  INTEGER as lportBuTrkOnFailure  
  INTEGER as lportTrkFailureThrsh  
  INTEGER as lportTrkRestThrsh  
  INTEGER as lportBuTrkRetryInt  
  INTEGER as lportBuTrkRetryNum  
  INTEGER as lportBuTrkCycleInt  
  INTEGER as lportTrkManualBu  
  Index as lportPrimTrk  
  INTEGER as lportInitCallSetup  
  INTEGER as lportBuFailReason  
  INTEGER as lportQ922Enable  
  INTEGER as lportQ922State  
  INTEGER as lportTrkPduRevision  
  INTEGER as lportPVCMgrPduRevision  
  INTEGER as lportDS0LoopStatus  
  INTEGER as lportISDNDuration  
  OCTET STRING as lportISDNSourceAddr  
  OCTET STRING as lportISDNDestAddr  
  IpAddress as lportISDNIpAddr  
  INTEGER as lportISDNCallRejCause  
  INTEGER as lportLastInvalidDLCI  
  INTEGER as lportTrkProtState  
  INTEGER as lportTrkTrafficMix  
  INTEGER as lportNumVC  
  INTEGER as lportTrkAdminCost  
  INTEGER as lportPrivateNet  
  INTEGER as lportTrkStaticDelay  
  INTEGER as lportTrkDynamicDelay  
  INTEGER as lportAtmDataRateQoS1  
  INTEGER as lportAtmDataRateQoS2  
  INTEGER as lportAtmDataRateQoS3  
  INTEGER as lportAtmDataRateQoS4  
  INTEGER as lportOutVAvailbwQoS1  
  INTEGER as lportOutVAvailbwQoS2  
  INTEGER as lportOutVAvailbwQoS3  
  INTEGER as lportOutVAvailbwQoS4  
  INTEGER as lportInVAvailbwQoS1  
  INTEGER as lportInVAvailbwQoS2  
  INTEGER as lportInVAvailbwQoS3  
  INTEGER as lportInVAvailbwQoS4  
  INTEGER as lportOutAllocbwQoS1  
  INTEGER as lportOutAllocbwQoS2  
  INTEGER as lportOutAllocbwQoS3  
  INTEGER as lportOutAllocbwQoS4  
  INTEGER as lportInAllocbwQoS1  
  INTEGER as lportInAllocbwQoS2  
  INTEGER as lportInAllocbwQoS3  
  INTEGER as lportInAllocbwQoS4  
  INTEGER as lportDynamicQoSbw  
  INTEGER as lportSVCRetryTimer  
  INTEGER as lportAtmNetworkType  
  INTEGER as lportAtmRouteMetricQoS1  
  INTEGER as lportAtmRouteMetricQoS2  
  INTEGER as lportAtmRouteMetricQoS3  
  INTEGER as lportAtmRouteMetricQoS4  
  INTEGER as lportIlmiPollTimeout  
  INTEGER as lportAtmProtocol  
  INTEGER as lportIlmiAdminStatus  
  INTEGER as lportIlmiOperStatus  
  Counter as lportIlmiPollRetry  
  INTEGER as lportAtmVpiBits  
  INTEGER as lportAtmVciBits  
  INTEGER as lportAtmOamAlarmEnable  
  INTEGER as lportInVAvailbw  
  INTEGER as lportbwUNIPolicy  
  INTEGER as lportStarvation  
  INTEGER as lportRecOverflow  
  INTEGER as lportLossOfCellSequence  
  INTEGER as lportLossOfStructurePointer  
  Counter as lportCbrInsDummyCells  
  Counter as lportRecFifoUnderflowCnt  
  Counter as lportRecFifoOverflowCnt  
  Counter as lportCbrLossOfStructurePointerCnt  
  Counter as lportCbrLossOfCellSequenceCnt  
  INTEGER as lportShaperId  
  INTEGER as lportIlmiPrefixScreenMode  
  INTEGER as lportSmdsPduViolTca  
  INTEGER as lportSmdsPduViolThresh  
  OCTET STRING as lportSmdsPduHdrSip3SaNotFound  
  OCTET STRING as lportSmdsPduHdrSip3SaDaOnSamePort  
  OCTET STRING as lportSmdsPduHdrSip3DstGaNotFound  
  OCTET STRING as lportSmdsPduHdrSip3DstIaScrnFail  
  OCTET STRING as lportSmdsPduHdrSip3SaValFail  
  OCTET STRING as lportSmdsPduHdrSip3DstIaNotFound  
  OCTET STRING as lportSmdsPduHdrSip3SrcIaScrnFail  
  OCTET STRING as lportSmdsPduHdrSip3DstGaScrnFail  
  OCTET STRING as lportSmdsPduHdrSip3SaTypeInvalid  
  OCTET STRING as lportSmdsPduHdrSip3DaTypeInvalid  
  OCTET STRING as lportSmdsPduHdrDxi2LinkIdInvalid  
  OCTET STRING as lportSmdsPduHdrDxi2CrInvalid  
  OCTET STRING as lportSmdsPduHdrDxi2CtrlInvalid  
  OCTET STRING as lportSmdsPduHdrDxi2StationIdInvalid  
  OCTET STRING as lportSmdsPduHdrDxi2AeInvalid  
  INTEGER as lportDS0FarendLpbkEnabled  
  INTEGER as lportDS0FarendLpbkDisabled  
  INTEGER as lportTrkProtFailureThreshold  
  OCTET STRING as lportPtr  
  INTEGER as lportISDNPoolUtil  
  INTEGER as lportISDNIpAddrAssignFail  
  INTEGER as lportTrkUtilQoS1  
  INTEGER as lportTrkUtilQoS2  
  INTEGER as lportTrkUtilQoS3  
  INTEGER as lportTrkUtilQoS4  
  Counter as lportInCells  
  Counter as lportOutCells  

CktEntry  
SEQUENCE    
  Index as cktSrcIfIndex  
  INTEGER as cktSrcDlci  
  INTEGER as cktPriority  
  INTEGER as cktCir  
  INTEGER as cktBc  
  INTEGER as cktBe  
  INTEGER as cktDestNodeId  
  INTEGER as cktDestIfIndex  
  INTEGER as cktDestDlci  
  INTEGER as cktTos  
  INTEGER as cktOde  
  INTEGER as cktAdminStatus  
  TimeTicks as cktCreationTime  
  TimeTicks as cktLastTimeChange  
  INTEGER as cktVcState  
  INTEGER as cktDceState  
  INTEGER as cktDteStatus  
  INTEGER as cktRnr  
  INTEGER as cktNiDown  
  INTEGER as cktDteState  
  INTEGER as cktOperStatus  
  INTEGER as cktOutForward  
  INTEGER as cktRerouteCnt  
  OCTET STRING as cktVcPtr  
  INTEGER as cktHopCnt  
  OCTET STRING as cktPath  
  INTEGER as cktFailReason  
  INTEGER as cktFailNode  
  INTEGER as cktFailPort  
  INTEGER as cktMcastGroupId  
  OCTET STRING as cktMcastMemberList  
  OCTET STRING as cktMcastParentGroups  
  Counter as cktInFrames  
  Counter as cktInDEFrames  
  Counter as cktInODEFrames  
  Counter as cktInFECNFrames  
  Counter as cktInBECNFrames  
  Counter as cktInDiscards  
  Counter as cktInOctets  
  Counter as cktInDEOctets  
  Counter as cktInODEOctets  
  Counter as cktOutFrames  
  Counter as cktOutDEFrames  
  Counter as cktOutODEFrames  
  Counter as cktOutFECNFrames  
  Counter as cktOutBECNFrames  
  Counter as cktOutOctets  
  Counter as cktOutDEOctets  
  Counter as cktOutODEOctets  
  Counter as cktOutLostFrames  
  Counter as cktOutLostDEFrames  
  Counter as cktOutLostODEFrames  
  Counter as cktOutLostOctets  
  Counter as cktOutLostDEOctets  
  Counter as cktOutLostODEOctets  
  INTEGER as cktRtMinDelay  
  INTEGER as cktRtMaxDelay  
  INTEGER as cktRtAvgDelay  
  INTEGER as cktDiagTestId  
  INTEGER as cktDiagTestRuns  
  INTEGER as cktHelloCounter  
  INTEGER as cktHelloAckCounter  
  OCTET STRING as cktDefinedPath  
  INTEGER as cktDefinedPathCount  
  INTEGER as cktDefinedPathEnable  
  INTEGER as cktDefinedPathAltOption  
  INTEGER as cktUsingDefinedPath  
  INTEGER as cktTryAltPath  
  INTEGER as cktNotVirgin  
  INTEGER as cktInForward  
  INTEGER as cktBtusSeg  
  Counter as cktInSegmentsDiscards  
  INTEGER as cktAtmVPI  
  INTEGER as cktAtmVCI  
  INTEGER as cktType  
  OCTET STRING as cktSvcCallingParty  
  OCTET STRING as cktSvcCalledParty  
  TimeTicks as cktSvcDuration  
  INTEGER as cktSvcCause  
  INTEGER as cktXlatFlag  
  INTEGER as cktDestLaddr  
  INTEGER as cktSrcLaddr  
  INTEGER as cktLoop  
  INTEGER as cktRerouteBalance  
  INTEGER as cktCallingBackup  
  INTEGER as cktRCir  
  INTEGER as cktAtmQoS  
  Counter as cktAtmInCells  
  Counter as cktAtmOutCells  
  Counter as cktAtmInDiscardedClp0Cells  
  Counter as cktAtmInDiscardedClp1Cells  
  INTEGER as cktAtmVcType  
  INTEGER as cktAtmPCR  
  INTEGER as cktAtmSCR  
  INTEGER as cktAtmMBS  
  Counter as cktAtmInPassedClp0Cells  
  Counter as cktAtmInPassedClp1Cells  
  Counter as cktAtmInTaggedCells  
  Counter as cktAtmOutClp0Cells  
  Counter as cktAtmOutClp1Cells  
  INTEGER as cktAtmRQoS  
  INTEGER as cktAtmTfdType  
  INTEGER as cktAtmRTfdType  
  INTEGER as cktAtmTfdParam1  
  INTEGER as cktAtmTfdParam2  
  INTEGER as cktAtmTfdParam3  
  INTEGER as cktAtmRTfdParam1  
  INTEGER as cktAtmRTfdParam2  
  INTEGER as cktAtmRTfdParam3  
  INTEGER as cktAtmFrameIWF  
  INTEGER as cktAtmUserPlane  
  INTEGER as cktRBc  
  INTEGER as cktRBe  
  INTEGER as cktOamLoopbackDirection  
  INTEGER as cktOamLoopbackType  
  INTEGER as cktOamLoopbackHops  
  INTEGER as cktOamLoopbackCount  
  Counter as cktOamLoopbackReceived  
  Counter as cktOamLoopbackTimeouts  
  INTEGER as cktOamLoopbackReceivedHigh  
  INTEGER as cktOamLoopbackReceivedLow  
  INTEGER as cktOamLoopbackReceivedAvg  
  INTEGER as cktOamAlarmDisable  
  INTEGER as cktShaperId  
  INTEGER as cktOspfCtd  
  INTEGER as cktOspfCdv  
  INTEGER as cktOutPort  
  INTEGER as cktOutVc  
  INTEGER as cktRVc  
  INTEGER as cktEntryType  
  OCTET STRING as cktDiagStr  
  INTEGER as cktSvcAalType  
  INTEGER as cktSvcBBearerClass  
  INTEGER as cktSvcBBearerClippingSusc  
  INTEGER as cktSvcBBearerTmgReq  
  INTEGER as cktSvcBBearerTfcType  
  INTEGER as cktAtmUPCEnable  
  INTEGER as cktRPriority  
  INTEGER as cktRtPriority  
  INTEGER as cktDeltaBc  
  INTEGER as cktDeltaBe  
  INTEGER as cktDeltaRBc  
  INTEGER as cktDeltaRBe  
  INTEGER as cktRedFrPcnt  
  INTEGER as cktRedFrRPcnt  
  INTEGER as cktRateEnforceSchm  
  INTEGER as cktRateEnforceRSchm  
  INTEGER as cktROde  
  INTEGER as cktPrivateNet  
  INTEGER as cktPrivateNetOverflow  
  INTEGER as cktCustomerID  
  INTEGER as cktAtmCDVT  
  INTEGER as cktNdcEnable  
  INTEGER as cktInterworkingFrToAtmCLP  
  INTEGER as cktInterworkingFrToAtmDe  
  INTEGER as cktNrtsCLP1  
  Counter as cktNrtsDiscardClp0  
  Counter as cktNrtsDiscardClp1  
  INTEGER as cktMPEnableAMF  
  INTEGER as cktMPEligible  
  INTEGER as cktMPForcedCaller  
  INTEGER as cktMPForcedCallee  
  INTEGER as cktFrameSize  
  INTEGER as cktRFrameSize  
  INTEGER as cktRNrtsCLP1  
  INTEGER as cktBBearerAtmTransferCapability  
  INTEGER as cktAtmFrameDiscard  
  INTEGER as cktRAtmFrameDiscard  
  INTEGER as cktAbrFRMRTT  
  INTEGER as cktAbrICR  
  INTEGER as cktRAbrICR  
  INTEGER as cktAbrRIF  
  INTEGER as cktRAbrRIF  
  INTEGER as cktAbrRDF  
  INTEGER as cktRAbrRDF  
  INTEGER as cktAbrTBE  
  INTEGER as cktRAbrTBE  
  INTEGER as cktAbrNRM  
  INTEGER as cktRAbrNRM  
  INTEGER as cktAbrTRM  
  INTEGER as cktRAbrTRM  
  INTEGER as cktAbrCDF  
  INTEGER as cktRAbrCDF  
  INTEGER as cktAbrADTF  
  INTEGER as cktRAbrADTF  
  INTEGER as cktAccumCTD  
  INTEGER as cktAccumCDV  
  INTEGER as cktAccumRCDV  
  INTEGER as cktCLR  
  INTEGER as cktRCLR  
  INTEGER as cktAtmLijId  
  INTEGER as cktAtmLijType  
  INTEGER as cktRtLastDelay  
  INTEGER as cktRtAccuMinDelay  
  INTEGER as cktRtAccuMaxDelay  
  INTEGER as cktRtAccuAvgDelay  
  INTEGER as cktQosIntPeriod  
  Counter as cktAtmOutOAMClp0Cells  
  Counter as cktAtmOutOAMClp1Cells  
  INTEGER as cktReqCTD  
  Counter as cktInOctetsPeak  
  Counter as cktOutOctetsPeak  
  Counter as cktInDEOctetsPeak  
  Counter as cktOutDEOctetsPeak  
  Counter as cktInODEOctetsPeak  
  Counter as cktOutODEOctetsPeak  
  INTEGER as cktAdminCostThreshold  
  INTEGER as cktAtmSvcServiceCategory  
  INTEGER as cktAtmSvcRServiceCategory  
  INTEGER as cktInterworkingFrToAtmEFCI  
  INTEGER as cktDiagSARMon  
  INTEGER as cktAdminCostReal  
  Counter as cktAtmInClp0Cells  
  Counter as cktAtmInClp1Cells  
  Counter as cktATMAAL5CRC32Error  
  Counter as cktATMAAL5CPIError  
  Counter as cktATMAAL5LengthError  
  Counter as cktATMAAL5ReassemblyTimerError  
  Counter as cktATMAAL5MaxNrSegError  
  Counter as cktIWF1490to1483Error  
  DisplayString as cktIWF1490to1483LastBadHeader  
  Counter as cktIWF1483to1490Error  
  DisplayString as cktIWF1483to1490LastBadHeader  

CktLeafEntry  
SEQUENCE    
  Index as cktLeafSrcIfIndex  
  INTEGER as cktLeafSrcDlci  
  INTEGER as cktLeafEndpointIndex  
  TimeTicks as cktLeafCreationTime  
  Index as cktLeafEgressIfIndex  
  INTEGER as cktLeafEgressDlci  
  INTEGER as cktLeafDestNodeId  
  Index as cktLeafDestIfIndex  
  INTEGER as cktLeafDestDlci  
  OCTET STRING as cktLeafSvcCallingParty  
  OCTET STRING as cktLeafSvcCalledParty  
  INTEGER as cktLeafAdminStatus  
  INTEGER as cktLeafVcState  
  INTEGER as cktLeafOperStatus  
  INTEGER as cktLeafDceState  
  INTEGER as cktLeafDteStatus  
  INTEGER as cktLeafDteState  
  OCTET STRING as cktLeafVcPtr  
  INTEGER as cktLeafHopCnt  
  OCTET STRING as cktLeafPath  
  INTEGER as cktLeafFailReason  
  INTEGER as cktLeafFailNode  
  INTEGER as cktLeafFailPort  
  INTEGER as cktLeafHelloCounter  
  INTEGER as cktLeafHelloAckCounter  
  INTEGER as cktLeafAtmVPI  
  INTEGER as cktLeafAtmVCI  
  INTEGER as cktLeafType  
  Counter as cktLeafAtmInCells  
  Counter as cktLeafAtmOutCells  
  Counter as cktLeafAtmInDiscardedClp0Cells  
  Counter as cktLeafAtmInDiscardedClp1Cells  
  Counter as cktLeafAtmInPassedClp0Cells  
  Counter as cktLeafAtmInPassedClp1Cells  
  Counter as cktLeafAtmInTaggedCells  
  Counter as cktLeafAtmOutClp0Cells  
  Counter as cktLeafAtmOutClp1Cells  

CktSmdsRtEntry  
SEQUENCE    
  INTEGER as cktSmdsRemoteNode  
  INTEGER as cktSmdsHopCnt  
  OCTET STRING as cktSmdsRoute  
  INTEGER as cktSmdsLocalPort  
  INTEGER as cktSmdsRemotePort  
  INTEGER as cktSmdsVcState  

Dsx1ConfigEntry  
SEQUENCE    
  INTEGER as dsx1SlotId  
  INTEGER as dsx1PortId  
  INTEGER as dsx1TimeElapsed  
  INTEGER as dsx1ValidIntervals  
  INTEGER as dsx1LineType  
  INTEGER as dsx1LineCoding  
  INTEGER as dsx1SendCode  
  DisplayString as dsx1CircuitIdentifier  
  INTEGER as dsx1LoopbackConfig  
  INTEGER as dsx1LineStatus  
  INTEGER as dsx1SignalMode  
  INTEGER as dsx1TransmitClockSource  
  INTEGER as dsx1Fdl  
  INTEGER as dsx1FdlVersion  

Dsx1CurrentEntry  
SEQUENCE    
  INTEGER as dsx1CurrentSlotId  
  INTEGER as dsx1CurrentPortId  
  Gauge as dsx1CurrentESs  
  Gauge as dsx1CurrentSESs  
  Gauge as dsx1CurrentSEFSs  
  Gauge as dsx1CurrentUASs  
  Gauge as dsx1CurrentCSSs  
  Gauge as dsx1CurrentBESs  

Dsx1IntervalEntry  
SEQUENCE    
  INTEGER as dsx1IntervalSlotId  
  INTEGER as dsx1IntervalPortId  
  INTEGER as dsx1IntervalNumber  
  Gauge as dsx1IntervalESs  
  Gauge as dsx1IntervalSESs  
  Gauge as dsx1IntervalSEFSs  
  Gauge as dsx1IntervalUASs  
  Gauge as dsx1IntervalCSSs  
  Gauge as dsx1IntervalBESs  

Dsx1TotalEntry  
SEQUENCE    
  INTEGER as dsx1TotalSlotId  
  INTEGER as dsx1TotalPortId  
  Gauge as dsx1TotalESs  
  Gauge as dsx1TotalSESs  
  Gauge as dsx1TotalSEFSs  
  Gauge as dsx1TotalUASs  
  Gauge as dsx1TotalCSSs  
  Gauge as dsx1TotalBESs  

SmdsaddrEntry  
SEQUENCE    
  OCTET STRING as smdsaddrAddr  
  INTEGER as smdsaddrType  
  INTEGER as smdsaddrId  
  INTEGER as smdsaddrIf  
  OCTET STRING as smdsaddrParentGrpMap  
  OCTET STRING as smdsaddrParentScrnMap  
  OCTET STRING as smdsaddrMemberAddrMap  
  INTEGER as smdsaddrAdminStatus  
  INTEGER as smdsaddrSlot  
  INTEGER as smdsaddrSsiIfNum  

IsdnAddrEntry  
SEQUENCE    
  INTEGER as isdnAddrIf  
  OCTET STRING as isdnAddr  
  INTEGER as isdnChanType  

IsdnCallerIDEntry  
SEQUENCE    
  INTEGER as isdnCallerIDIf  
  OCTET STRING as isdnCallerIDAddr  
  INTEGER as isdnCallerAdminStatus  

NamebindingEntry  
SEQUENCE    
  INTEGER as nameType  
  OCTET STRING as nameName  
  INTEGER as namePrimary  
  INTEGER as nameIfIndex  
  INTEGER as nameNodeId  
  INTEGER as nameStatus  

SvcNodePrefixEntry  
SEQUENCE    
  OCTET STRING as svcNodePrefixPrefix  
  INTEGER as svcNodePrefixNumBits  
  INTEGER as svcNodePrefixNmbPlan  
  INTEGER as svcNodePrefixAdminStatus  

SvcPrefixEntry  
SEQUENCE    
  Index as svcPrefixIfIndex  
  OCTET STRING as svcPrefixPrefix  
  INTEGER as svcPrefixNumBits  
  INTEGER as svcPrefixNmbPlan  
  INTEGER as svcPrefixAdminCost  
  OCTET STRING as svcPrefixLocalGatewayAddress  
  INTEGER as svcPrefixLocalGatewayNmbPlan  
  OCTET STRING as svcPrefixRemoteGatewayAddress  
  INTEGER as svcPrefixRemoteGatewayNmbPlan  
  INTEGER as svcPrefixAdminStatus  

SvcAddrEntry  
SEQUENCE    
  Index as svcAddrIfIndex  
  OCTET STRING as svcAddrAddress  
  INTEGER as svcAddrNmbPlan  
  INTEGER as svcAddrAdminStatus  

SvcAtmUserPartEntry  
SEQUENCE    
  Index as svcAtmUserPartIfIndex  
  OCTET STRING as svcAtmUserPartUserPart  
  INTEGER as svcAtmUserPartAdminStatus  

SvcConfigEntry  
SEQUENCE    
  Index as svcConfigIfIndex  
  IpAddress as svcConfigInitiateIdentStatsUpload  
  INTEGER as svcConfigCgPtyInsertionMode  
  OCTET STRING as svcConfigCgPtyInsertionAddress  
  INTEGER as svcConfigCgPtyInsertionNmbPlan  
  INTEGER as svcConfigCgPtyScreenMode  
  INTEGER as svcConfigEgressAddrXlateMode  
  INTEGER as svcConfigIngressAddrXlateMode  
  INTEGER as svcConfigCgPtyPresentationMode  

SvcAtmConfigEntry  
SEQUENCE    
  Index as svcAtmConfigIfIndex  
  INTEGER as svcAtmConfigAdminStatus  
  INTEGER as svcAtmConfigOperStatus  
  INTEGER as svcAtmConfigQ93bMaxRestart  
  INTEGER as svcAtmConfigQ93bMaxStatEnq  
  INTEGER as svcAtmConfigQ93bT303  
  INTEGER as svcAtmConfigQ93bT308  
  INTEGER as svcAtmConfigQ93bT309  
  INTEGER as svcAtmConfigQ93bT310  
  INTEGER as svcAtmConfigQ93bT313  
  INTEGER as svcAtmConfigQ93bT316  
  INTEGER as svcAtmConfigQ93bT322  
  INTEGER as svcAtmConfigQ93bT398  
  INTEGER as svcAtmConfigQ93bT399  
  Counter as svcAtmConfigQ93bTotalConns  
  Counter as svcAtmConfigQ93bActiveConns  
  INTEGER as svcAtmConfigQ93bLastCauseTx  
  INTEGER as svcAtmConfigQ93bLastCauseRx  
  Counter as svcAtmConfigQ93bNumSetupPduTx  
  Counter as svcAtmConfigQ93bNumSetupPduRx  
  Counter as svcAtmConfigQ93bNumCallProcPduTx  
  Counter as svcAtmConfigQ93bNumCallProcPduRx  
  Counter as svcAtmConfigQ93bNumConnectPduTx  
  Counter as svcAtmConfigQ93bNumConnectPduRx  
  Counter as svcAtmConfigQ93bNumConnectAckPduTx  
  Counter as svcAtmConfigQ93bNumConnectAckPduRx  
  Counter as svcAtmConfigQ93bNumReleasePduTx  
  Counter as svcAtmConfigQ93bNumReleasePduRx  
  Counter as svcAtmConfigQ93bNumReleaseCmpltPduTx  
  Counter as svcAtmConfigQ93bNumReleaseCmpltPduRx  
  Counter as svcAtmConfigQ93bNumAddPtyPduTx  
  Counter as svcAtmConfigQ93bNumAddPtyPduRx  
  Counter as svcAtmConfigQ93bNumAddPtyAckPduTx  
  Counter as svcAtmConfigQ93bNumAddPtyAckPduRx  
  Counter as svcAtmConfigQ93bNumAddPtyRejPduTx  
  Counter as svcAtmConfigQ93bNumAddPtyRejPduRx  
  Counter as svcAtmConfigQ93bNumDropPtyPduTx  
  Counter as svcAtmConfigQ93bNumDropPtyPduRx  
  Counter as svcAtmConfigQ93bNumDropPtyAckPduTx  
  Counter as svcAtmConfigQ93bNumDropPtyAckPduRx  
  Counter as svcAtmConfigQ93bNumStatusEnqPduTx  
  Counter as svcAtmConfigQ93bNumStatusEnqPduRx  
  Counter as svcAtmConfigQ93bNumStatusPduTx  
  Counter as svcAtmConfigQ93bNumStatusPduRx  
  Counter as svcAtmConfigQ93bNumRestartPduTx  
  Counter as svcAtmConfigQ93bNumRestartPduRx  
  Counter as svcAtmConfigQ93bNumRestartAckPduTx  
  Counter as svcAtmConfigQ93bNumRestartAckPduRx  
  INTEGER as svcAtmConfigQSaalMaxCC  
  INTEGER as svcAtmConfigQSaalMaxPD  
  INTEGER as svcAtmConfigQSaalMaxStat  
  INTEGER as svcAtmConfigQSaalTPoll  
  INTEGER as svcAtmConfigQSaalTKeepalive  
  INTEGER as svcAtmConfigQSaalTNoResponse  
  INTEGER as svcAtmConfigQSaalTCC  
  INTEGER as svcAtmConfigQSaalTIdle  
  Counter as svcAtmConfigQSaalNumDiscardTx  
  Counter as svcAtmConfigQSaalNumDiscardRx  
  Counter as svcAtmConfigQSaalNumErrorTx  
  Counter as svcAtmConfigQSaalNumErrorRx  
  Counter as svcAtmConfigQSaalNumBgnPduTx  
  Counter as svcAtmConfigQSaalNumBgnPduRx  
  Counter as svcAtmConfigQSaalNumBgakPduTx  
  Counter as svcAtmConfigQSaalNumBgakPduRx  
  Counter as svcAtmConfigQSaalNumBgrejPduTx  
  Counter as svcAtmConfigQSaalNumBgrejPduRx  
  Counter as svcAtmConfigQSaalNumEndPduTx  
  Counter as svcAtmConfigQSaalNumEndPduRx  
  Counter as svcAtmConfigQSaalNumEndakPduTx  
  Counter as svcAtmConfigQSaalNumEndakPduRx  
  Counter as svcAtmConfigQSaalNumRsPduTx  
  Counter as svcAtmConfigQSaalNumRsPduRx  
  Counter as svcAtmConfigQSaalNumRsakPduTx  
  Counter as svcAtmConfigQSaalNumRsakPduRx  
  Counter as svcAtmConfigQSaalNumErPduTx  
  Counter as svcAtmConfigQSaalNumErPduRx  
  Counter as svcAtmConfigQSaalNumErakPduTx  
  Counter as svcAtmConfigQSaalNumErakPduRx  
  Counter as svcAtmConfigQSaalNumSdPduTx  
  Counter as svcAtmConfigQSaalNumSdPduRx  
  Counter as svcAtmConfigQSaalNumPollPduTx  
  Counter as svcAtmConfigQSaalNumPollPduRx  
  Counter as svcAtmConfigQSaalNumStatPduTx  
  Counter as svcAtmConfigQSaalNumStatPduRx  
  Counter as svcAtmConfigQSaalNumUstatPduTx  
  Counter as svcAtmConfigQSaalNumUstatPduRx  
  Counter as svcAtmConfigQSaalNumUdPduTx  
  Counter as svcAtmConfigQSaalNumUdPduRx  
  Counter as svcAtmConfigQSaalNumMdPduTx  
  Counter as svcAtmConfigQSaalNumMdPduRx  

SvcAtmFailedCallEntry  
SEQUENCE    
  Index as svcAtmFailedCallIfIndex  
  INTEGER as svcAtmFailedCallIndex  
  INTEGER as svcAtmFailedCallDirection  
  INTEGER as svcAtmFailedCallPduType  
  INTEGER as svcAtmFailedCallPduDirection  
  INTEGER as svcAtmFailedCallCause  
  INTEGER as svcAtmFailedCallLocation  
  OCTET STRING as svcAtmFailedCallDiagnostic  
  TimeTicks as svcAtmFailedCallCreationTime  
  TimeTicks as svcAtmFailedCallTerminationTime  
  INTEGER as svcAtmFailedCallFailureNodeId  
  Index as svcAtmFailedCallFailureIfIndex  
  OCTET STRING as svcAtmFailedCallCallingParty  
  OCTET STRING as svcAtmFailedCallCalledParty  
  INTEGER as svcAtmFailedCallAtmTfdType  
  INTEGER as svcAtmFailedCallAtmTfdParam1  
  INTEGER as svcAtmFailedCallAtmTfdParam2  
  INTEGER as svcAtmFailedCallAtmTfdParam3  
  INTEGER as svcAtmFailedCallAtmQosClass  
  INTEGER as svcAtmFailedCallAtmRTfdType  
  INTEGER as svcAtmFailedCallAtmRTfdParam1  
  INTEGER as svcAtmFailedCallAtmRTfdParam2  
  INTEGER as svcAtmFailedCallAtmRTfdParam3  
  INTEGER as svcAtmFailedCallAtmRQoSClass  
  INTEGER as svcAtmFailedCallBBearerClass  
  INTEGER as svcAtmFailedCallBBearerTfcType  
  INTEGER as svcAtmFailedCallBBearerTmgRqmt  
  INTEGER as svcAtmFailedCallBBearerUplaneCfg  
  INTEGER as svcAtmFailedCallBBearerClippingSusc  
  INTEGER as svcAtmFailedCallAdminStatus  

SwEntry  
SEQUENCE    
  INTEGER as swLogicalSlotId  
  INTEGER as swRedundState  
  DisplayString as swRevision  
  DisplayString as swBuildID  
  DisplayString as swBuildDate  
  DisplayString as swBuildDescription  
  DisplayString as swCopyrightNotice  
  INTEGER as swCapabilityMask  
  INTEGER as swFeatureMask  
  INTEGER as swPatchMask  
  DisplayString as swBuildUserId  
  DisplayString as swBuildView  
  DisplayString as swBuildConfigSpec