
CENTILLION-MCAST-MIB
File:
CENTILLION-MCAST-MIB.mib (14080 bytes)
Imported modules
Imported symbols
Defined Objects
| vlan |
1.3.6.1.4.1.930.2.1.2.31 |
| OBJECT IDENTIFIER |
|
|
|
| igmpGeneralConfigEntry |
1.3.6.1.4.1.930.2.1.2.31.1.1.1.1.1 |
| IP IGMP general configuration entry. Each entry is indexed by a vlan id. An example to create the entry is: set igmpGeneralConfigIgmpSupport.3=I2 and igmpGeneralConfigMaxGroup.3=I20 to a switch ip address. (where 3 is vlan Id; 2 is enabled; 20 is maximum multicast groups to be supported for this vlan. |
| OBJECT-TYPE |
|
|
|
| |
IgmpGeneralConfigEntry |
|
|
| igmpGeneralConfigPseudoQuery |
1.3.6.1.4.1.930.2.1.2.31.1.1.1.1.1.2 |
| In the absence of a true IGMP router, the switch may be configured to issue general queries. This provides the capability for multicast pruning with an isoloated subnet. The mode defaults to disabled in a VLAN configured for IGMP support |
| OBJECT-TYPE |
|
|
|
| |
EnableIndicator |
|
|
| igmpGeneralConfigMaxGroup |
1.3.6.1.4.1.930.2.1.2.31.1.1.1.1.1.5 |
| The maximum number of multicast groups supported in this VLAN. If the VLAN supports only manually configured multicast groups, then the value of this field equals the length of the IGMP multicast group if the multicast group is an inclusive set. A value of 0 indicates that IGMP multicasting is not supported in this VLAN |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| igmpTimerConfigEntry |
1.3.6.1.4.1.930.2.1.2.31.1.1.1.2.1 |
| IP IGMP Multicast timer configuration entry. Each entry is indexed by a vlan id. This entry will be created when the corresponding igmpGeneralConfigEntry is created. All the values of the mibs in this entry will be set to default at the time of creation. |
| OBJECT-TYPE |
|
|
|
| |
IgmpTimerConfigEntry |
|
|
| igmpTimerConfigTimerRobustness |
1.3.6.1.4.1.930.2.1.2.31.1.1.1.2.1.2 |
| The robustness variable for the multicast group. A value of zero indicates the default value should be taken. If the value specified is non-zero, it should be equal or greater than 2 |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| igmpTimerConfigQueryInterval |
1.3.6.1.4.1.930.2.1.2.31.1.1.1.2.1.3 |
| The query interval configured for the multicast group. A value of zero indicates the default value should be used. The value should be less than 0xffff |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| igmpTimerConfigQueryResponse |
1.3.6.1.4.1.930.2.1.2.31.1.1.1.2.1.4 |
| The response interval configured for the multicast group. A value of zero indicates the default value should be used. The value should be less than 0xffff. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| igmpGroupEntry |
1.3.6.1.4.1.930.2.1.2.31.1.1.1.3.1 |
| IP IGMP Multicast group configuration entry. Each entry is indexed by igmpGroupVlanId, igmpGroupStatic, and igmpGroupAddress |
| OBJECT-TYPE |
|
|
|
| |
IgmpGroupEntry |
|
|
| igmpGroupStatic |
1.3.6.1.4.1.930.2.1.2.31.1.1.1.3.1.2 |
| Indicates whether the IGMP multicast group was created statically(TRUE) by a management entity, or dynamically learned |
| OBJECT-TYPE |
|
|
|
| |
Boolean |
|
|
| igmpGroupAddress |
1.3.6.1.4.1.930.2.1.2.31.1.1.1.3.1.3 |
| The multicast group address(Class D). The range is from 224.0.0.0 to 239.255.255.255. The addresses from 224.0.0.0 to 224.0.0.255 are reserved IP multicast addresses. |
| OBJECT-TYPE |
|
|
|
| |
IpAddress |
|
|
| igmpGroupIncluded |
1.3.6.1.4.1.930.2.1.2.31.1.1.1.3.1.4 |
| Indicates the multicast addresses are to be included or excluded from the group. Dynamic entries are always included and can not be modified, while static entries may be either included or excluded. For each VLAN, it only allows to configure either 'included' as static or 'excluded' as static. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
included(1), excluded(2) |
|
| igmpGroupStatus |
1.3.6.1.4.1.930.2.1.2.31.1.1.1.3.1.5 |
| The status of this multicast group entry: 'valid' and 'invalid'. This object enables the user to add or delete this multicast group. Setting the status as 'valid' is to add the entry; otherwise as 'invalid' is to delete the entry. An example to create an multicast group entry is: set igmpGroupStatus.3.1.224.0.0.1= valid where 3: vlan id; 1: static; 224.0.0.1: multicast group IP address |
| OBJECT-TYPE |
|
|
|
| |
StatusIndicator |
|
|
| igmpRouterPortTable |
1.3.6.1.4.1.930.2.1.2.31.1.1.1.4 |
| IP IGMP Multicast router port table. It contains a list of the ports containing configured IGMP routers. These ports initialize the IPrDtag and IPmDtag for the group. |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
IgmpRouterPortEntry |
|
| igmpRouterPortEntry |
1.3.6.1.4.1.930.2.1.2.31.1.1.1.4.1 |
| IP IGMP Multicast router port entry. Each entry is indexed by igmpRouterPortVlanId, igmpRouterPortStatic, igmpRouterPortCard, igmpRouterPortPort |
| OBJECT-TYPE |
|
|
|
| |
IgmpRouterPortEntry |
|
|
| igmpRouterPortStatic |
1.3.6.1.4.1.930.2.1.2.31.1.1.1.4.1.2 |
| Indicates whether the IGMP multicast router port was created statically(TRUE) by a management entity, or dynamically learned. |
| OBJECT-TYPE |
|
|
|
| |
Boolean |
|
|
| igmpRouterPortStatus |
1.3.6.1.4.1.930.2.1.2.31.1.1.1.4.1.5 |
| The status of this multicast router port entry: 'valid' and 'invalid'. This object enables the user to add or delete this multicast group. Setting the status as 'valid' is to add the entry; otherwise as 'invalid' is to delete the entry. An example to create an multicast router port entry is: set igmpRouterPortStatus.3.1.5.2 = valid where 3: vlan id; 1: static; 5.2 : card/port that is connected with igmp router |
| OBJECT-TYPE |
|
|
|
| |
StatusIndicator |
|
|
Defined Objects
| IgmpGeneralConfigEntry |
|
| SEQUENCE |
|
|
|
| |
VlanId as igmpGeneralConfigVlanId |
|
|
| |
EnableIndicator as igmpGeneralConfigPseudoQuery |
|
|
| |
EnableIndicator as igmpGeneralConfigIrapQuery |
|
|
| |
EnableIndicator as igmpGeneralConfigIgmpSupport |
|
|
| |
INTEGER as igmpGeneralConfigMaxGroup |
|
|
| IgmpTimerConfigEntry |
|
| SEQUENCE |
|
|
|
| |
VlanId as igmpTimerConfigVlanId |
|
|
| |
INTEGER as igmpTimerConfigTimerRobustness |
|
|
| |
INTEGER as igmpTimerConfigQueryInterval |
|
|
| |
INTEGER as igmpTimerConfigQueryResponse |
|
|
| IgmpGroupEntry |
|
| SEQUENCE |
|
|
|
| |
VlanId as igmpGroupVlanId |
|
|
| |
Boolean as igmpGroupStatic |
|
|
| |
IpAddress as igmpGroupAddress |
|
|
| |
INTEGER as igmpGroupIncluded |
|
|
| |
StatusIndicator as igmpGroupStatus |
|
|
| IgmpRouterPortEntry |
|
| SEQUENCE |
|
|
|
| |
VlanId as igmpRouterPortVlanId |
|
|
| |
Boolean as igmpRouterPortStatic |
|
|
| |
CardId as igmpRouterPortCard |
|
|
| |
PortId as igmpRouterPortPort |
|
|
| |
StatusIndicator as igmpRouterPortStatus |
|
|