CISCO-ATM-DUAL-PHY-MIB

File: CISCO-ATM-DUAL-PHY-MIB.mib (12794 bytes)

Imported modules

SNMPv2-SMI RFC-1212 RFC-1215
SNMPv2-TC-v1 CISCO-TC IF-MIB
CISCO-SMI

Imported symbols

Counter32 OBJECT-TYPE TRAP-TYPE
TruthValue InterfaceIndexOrZero ifIndex
InterfaceIndex ciscoMgmt

Defined Objects

ciscoAtmDualPhyMIB 1.3.6.1.4.1.9.9.60
OBJECT IDENTIFIER    

ciscoAtmDualPhyMIBObjects 1.3.6.1.4.1.9.9.60.1
OBJECT IDENTIFIER    

cadpStatistics 1.3.6.1.4.1.9.9.60.1.1
OBJECT IDENTIFIER    

cadpStatTable 1.3.6.1.4.1.9.9.60.1.1.1
A table of status information about ATM phy.
OBJECT-TYPE    
  SEQUENCE OF  
    CadpStatEntry

cadpStatEntry 1.3.6.1.4.1.9.9.60.1.1.1.1
An Atm Phy table entry, containing information about a phy on this ATM module.
OBJECT-TYPE    
  CadpStatEntry  

cadpStatLossOfSignal 1.3.6.1.4.1.9.9.60.1.1.1.1.1
Set to true if the phy is currently experiencing a loss of signal (LOS) from its connected port. Set to false if the phy is not experiencing a loss of signal.
OBJECT-TYPE    
  TruthValue  

cadpStatFarEndReceiveFailure 1.3.6.1.4.1.9.9.60.1.1.1.1.2
Set to true if the phy is currently experiencing a far end receive failure (FERF) with its connected port. Set to false if the phy is not experiencing a far end receive failure.
OBJECT-TYPE    
  TruthValue  

cadpStatActive 1.3.6.1.4.1.9.9.60.1.1.1.1.5
Set to true when this phy is currently the active phy. Set to false when this phy is not the currently active phy.
OBJECT-TYPE    
  TruthValue  

cadpStatSectionBIP8Errors 1.3.6.1.4.1.9.9.60.1.1.1.1.6
The Bit Interleaved Parity 8 is an error checking code applied for quick isolation of faults. Each bit in the B octets is set to 1 or 0 as necessary to obtain even parity over the previous frame. The calculated BIP-8 code for frame N is compared with the BIP-8 code extracted from the B1 byte of frame N+1. Differences indicate that a section level bit error has occurred. Count of Section BIP-8 (Bit Interleaved Parity) errors that have been detected on this phy.
OBJECT-TYPE    
  Counter32  

cadpStatLineBIP824Errors 1.3.6.1.4.1.9.9.60.1.1.1.1.7
The Bit Interleaved Parity 8/24 is an error checking code based on even parity. The calculated BIP code for frame N is compared with the BIP-8/24 code extracted from the B2 byte(s) of frame N+1. Any differences indicate that a line layer bit error has occurred. Count of line bit interleaved partiy (BIP-8/24) errors on this phy.
OBJECT-TYPE    
  Counter32  

cadpStatLineFEBErrors 1.3.6.1.4.1.9.9.60.1.1.1.1.8
The number of bits (binary 000 to 1000) in the previous BIP-8 that didn't match the even parity check are inserted by the transmitter. The receiver checks for this in the M0/M1 byte of the frame. A non-zero value (legal range is binary 0000 - 1000) indicates a line layer error in the remote end. Any other value is treated as no error. Count of Line Far End Bit Errors (FEBE) on this phy.
OBJECT-TYPE    
  Counter32  

cadpStatPathBIP8Errors 1.3.6.1.4.1.9.9.60.1.1.1.1.9
The Bit Interleaved Parity 8 is an error checking code applied for quick isolation of faults. Each bit in the B octets is set to 1 or 0 as necessary to obtain even parity over the previous frame. The calculated BIP-8 code for frame N is compared with the BIP-8 code extracted from the B3 byte of frame N+1. Differences indicate that a Path level bit error has occurred. Count of Path BIP-8 (Bit Interleaved Parity) errors that have been detected on this phy.
OBJECT-TYPE    
  Counter32  

cadpStatPathFEBErrors 1.3.6.1.4.1.9.9.60.1.1.1.1.10
The number of B3 errors in the previous frame inserted by the transmitter. The receiver checks for this in the G1 byte of the frame. A non-zero value (legal range is binary 0000 - 1000) indicates a line layer error in the remote end. Any other value is treated as no error. Count of Path Far End Bit Errors (FEBE) on this phy.
OBJECT-TYPE    
  Counter32  

cadpStatCorrectableHCSErrors 1.3.6.1.4.1.9.9.60.1.1.1.1.11
The Header Checksum (HCS) is a CRC-8 calculation over the first 4 octets of the ATM cell header. The received HCS is verified using the polynomial x^8 + x^2 + x + 1. The coset polynomial x^6 + x^4 + x^2 + 1, is added (modulo 2) to the received HCS octet before comparison with the calculated result. Cells with single bit error in the HCS byte are corrected. Cells with more than one bit error in the HCS byte are uncorrectable. Count of incoming cells on this phy with single bit error in the Header Checksum (HCS) byte
OBJECT-TYPE    
  Counter32  

cadpStatUncorrectableHCSErrors 1.3.6.1.4.1.9.9.60.1.1.1.1.12
The Header Checksum (HCS) is a CRC-8 calculation over the first 4 octets of the ATM cell header. The received HCS is verified using the polynomial x^8 + x^2 + x + 1. The coset polynomial x^6 + x^4 + x^2 + 1, is added (modulo 2) to the received HCS octet before comparison with the calculated result. Cells with single bit error in the HCS byte are corrected. Cells with more than one bit error in the HCS byte are uncorrectable. Count of uncorrectable Header Checksum (HCS) errors on this phy.
OBJECT-TYPE    
  Counter32  

cadpStatOperActivePhy 1.3.6.1.4.1.9.9.60.1.1.2
Returns the ifIndex of the phy which is currently the active phy. A value of 0 indicates that no phy is currently active.
OBJECT-TYPE    
  InterfaceIndexOrZero  

cadpStatAdminActivePhy 1.3.6.1.4.1.9.9.60.1.1.3
Returns the ifIndex of the phy which is the preferred active phy. A value of 0 indicates that no phy is currently active. Setting this object to a value different from its current value causes the ATM module to make the indicated phy active, and the active phy inactive. Setting this object to its current value has no effect. After performing the phy change, the agent will update all phy information (including cadpStatOperActivePhy) and send a ciscoAtmDualPhyChange trap.
OBJECT-TYPE    
  InterfaceIndex  

ciscoAtmDualPhyMIBTrapPrefix 1.3.6.1.4.1.9.9.60.2
OBJECT IDENTIFIER    

ciscoAtmDualPhyMIBTraps 1.3.6.1.4.1.9.9.60.2.0
OBJECT IDENTIFIER    

ciscoAtmDualPhyChange 1.3.6.1.4.1.9.9.60.2.1
A ciscoAtmDualPhyChange trap is sent when the active phy changes either because of a failure or because of user intervention (setting cadpStatAdminActivePhy, for example).
TRAP-TYPE    
  cadpStatOperActivePhy  

ciscoAtmDualPhyMIBConformance 1.3.6.1.4.1.9.9.60.3
OBJECT IDENTIFIER    

ciscoAtmDualPhyMIBCompliances 1.3.6.1.4.1.9.9.60.3.1
OBJECT IDENTIFIER    

ciscoAtmDualPhyMIBCompliance 1.3.6.1.4.1.9.9.60.3.1.1
OBJECT IDENTIFIER    

ciscoAtmDualPhyMIBGroups 1.3.6.1.4.1.9.9.60.3.2
OBJECT IDENTIFIER    

ciscoAtmDualPhyMIBGroup 1.3.6.1.4.1.9.9.60.3.2.1
OBJECT IDENTIFIER    

Defined Objects

CadpStatEntry  
SEQUENCE    
  TruthValue as cadpStatLossOfSignal  
  TruthValue as cadpStatFarEndReceiveFailure  
  TruthValue as cadpStatActive  
  Counter32 as cadpStatSectionBIP8Errors  
  Counter32 as cadpStatLineBIP824Errors  
  Counter32 as cadpStatLineFEBErrors  
  Counter32 as cadpStatPathBIP8Errors  
  Counter32 as cadpStatPathFEBErrors  
  Counter32 as cadpStatCorrectableHCSErrors  
  Counter32 as cadpStatUncorrectableHCSErrors