CISCO-ENTITY-QFP-MIB

File: CISCO-ENTITY-QFP-MIB.mib (34179 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
ENTITY-MIB CISCO-SMI

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Gauge32
NOTIFICATION-TYPE Counter32 Counter64
Unsigned32 MODULE-COMPLIANCE OBJECT-GROUP
NOTIFICATION-GROUP TEXTUAL-CONVENTION DateAndTime
TruthValue entPhysicalIndex ciscoMgmt

Defined Objects

ciscoEntityQfpMIB 1.3.6.1.4.1.9.9.715
This MIB module defines managed objects that facilitate the management of Quantum Flow Processors (QFP), which are listed in the ENTITY-MIB (RFC 4133) entPhysicalTable as an entPhysicalClass of 'cpu'. The Quantum Flow Processors (QFP) technology is an architecture family developed by Cisco, which has fully integrated and programmable networking chip set that controls different functions of a system such as packet forwarding. This module contains objects to monitor various QFP statistics such as system, utilization, memory, etc. The utilization statistics can be used for future capacity planning. The calculation of this statistics may vary by devices which host QFPs, hence the user must refer to the specific device document of interest for the exact method of calculation. The utilization statistics have the following terminology. o Input - Communication channel where packets arrive on the QFP. o Output - Communication channel where packets leave the QFP. o Priority - A classification applied to packets indicating they should be treated with greater urgency. o Non-Priority - A classification applied to packets indicating they should be treated with lesser urgency. o Processing Load - The percentage of time over some interval that the QFP has spent forwarding packets, relative to the total time spent both forwarding packets and being idle.
MODULE-IDENTITY    

ciscoEntityQfpMIBNotifs 1.3.6.1.4.1.9.9.715.0
OBJECT IDENTIFIER    

ceqfpMemoryResRisingThreshNotif 1.3.6.1.4.1.9.9.715.0.1
A notification indicating that the QFP memory usage is rising the threshold on this memory resource. This notification will be sent, whenever the QFP memory usage (ceqfpMemoryResInUse) is equal to or above the rising threshold (ceqfpMemoryResRisingThreshold). An agent may throttle the generation of consecutive ceqfpMemoryResRisingThreshNotif notification so that there is at least a five second (suggested default) gap between notification of this type.
NOTIFICATION-TYPE    
  ceqfpMemoryResInUse  
  ceqfpMemoryResCurrentRisingThresh  

ceqfpMemoryResFallingThreshNotif 1.3.6.1.4.1.9.9.715.0.2
A notification indicating that the QFP memory usage is equal to or below the falling threshold on this memory resource. This notification will be sent, whenever the QFP memory usage (ceqfpMemoryResInUse) is equal to or below the falling threshold (ceqfpMemoryResFallingThreshold). An agent may throttle the generation of consecutive ceqfpMemoryResFallingThreshNotif notification so that there is at least a five second (suggested default) gap between notification of this type.
NOTIFICATION-TYPE    
  ceqfpMemoryResInUse  
  ceqfpMemoryResCurrentFallingThresh  

ciscoEntityQfpMIBObjects 1.3.6.1.4.1.9.9.715.1
OBJECT IDENTIFIER    

ciscoEntityQfp 1.3.6.1.4.1.9.9.715.1.1
OBJECT IDENTIFIER    

ceqfpSystemTable 1.3.6.1.4.1.9.9.715.1.1.1
This table maintains the QFP system information for each QFP physical entity. An agent creates a conceptual row to this table corresponding to a QFP physical entity upon detection of a physical entity supporting the QFP system information. An agent destroys a conceptual row from this table corresponding to a QFP physical entity upon removal of the QFP host physical entity.
OBJECT-TYPE    
  SEQUENCE OF  
    CeqfpSystemEntry

ceqfpSystemEntry 1.3.6.1.4.1.9.9.715.1.1.1.1
A conceptual row in the ceqfpSystemTable. There is an entry in this table for each QFP entity, as defined by a value of entPhysicalIndex.
OBJECT-TYPE    
  CeqfpSystemEntry  

ceqfpSystemTrafficDirection 1.3.6.1.4.1.9.9.715.1.1.1.1.1
This object represents the traffic direction that this QFP is assigned to process. The enumerated values are described below. none (1) - The QFP is not assigned to processes any traffic yet ingress (2) - The QFP processes inbound traffic egress (3) - The QFP processes outbound traffic both (4) - The QFP processes both inbound and outbound traffic
OBJECT-TYPE    
  INTEGER none(1), ingress(2), egress(3), both(4)  

ceqfpSystemState 1.3.6.1.4.1.9.9.715.1.1.1.1.2
This object represents the current QFP state. The enumerated values are described below. unknown (1) - The state of the QFP is unknown reset (2) - The QFP is reset init (3) - The QFP is being initialized active (4) - The QFP is active in a system with redundant QFP activeSolo (5) - The QFP is active and there is no redundant QFP in the system standby (6) - The QFP is standby in a redundant system. hotStandby (7) - The QFP is standby and synchronized with active, so that a switchover in this state will preserve state of the active. Stateful datapath features are synchronized between the active QFP and standby QFP
OBJECT-TYPE    
  INTEGER unknown(1), reset(2), init(3), active(4), activeSolo(5), standby(6), hotStandby(7)  

ceqfpNumberSystemLoads 1.3.6.1.4.1.9.9.715.1.1.1.1.3
This object represents the number of times the QFP is loaded, since the QFP host is up.
OBJECT-TYPE    
  Counter32  

ceqfpSystemLastLoadTime 1.3.6.1.4.1.9.9.715.1.1.1.1.4
This object represents the QFP last load time.
OBJECT-TYPE    
  DateAndTime  

ceqfpFiveSecondUtilAlgo 1.3.6.1.4.1.9.9.715.1.1.2
This objects represents the method used to calculate 5 Second interval utilization data. The enumerated values are described below. unknown (1) - The calculation method is unknown fiveSecSample (2) - The value is calculated based on the last 5 second sampling period of utilization data.
OBJECT-TYPE    
  INTEGER unknown(1), fiveSecSample(2)  

ceqfpOneMinuteUtilAlgo 1.3.6.1.4.1.9.9.715.1.1.3
This objects represents the method used to calculate 1 Minute interval utilization data. The enumerated values are described below. unknown (1) - The calculation method is unknown fiveSecSMA (2) - The value is calculated using Simple Moving Average of last 12 five seconds utilization data.
OBJECT-TYPE    
  INTEGER unknown(1), fiveSecSMA(2)  

ceqfpFiveMinutesUtilAlgo 1.3.6.1.4.1.9.9.715.1.1.4
This objects represents the method used to calculate 5 Minutes interval utilization data. The enumerated values are described below. unknown (1) - The calculation method is unknown fiveSecSMA (2) - The value is calculated using Simple Moving Average of last 60 five seconds utilization data.
OBJECT-TYPE    
  INTEGER unknown(1), fiveSecSMA(2)  

ceqfpSixtyMinutesUtilAlgo 1.3.6.1.4.1.9.9.715.1.1.5
This objects represents the method used to calculate 60 Minutes interval utilization data. The enumerated values are described below. unknown (1) - The calculation method is unknown fiveSecSMA (1) - The value is calculated using Simple Moving Average of last 720 five seconds utilization data.
OBJECT-TYPE    
  INTEGER unknown(1), fiveSecSMA(2)  

ceqfpUtilizationTable 1.3.6.1.4.1.9.9.715.1.1.6
This table maintains the utilization statistics collected by each QFP physical entity at various time interval such as last 5 seconds, 1 minute, etc. An agent creates a conceptual row to this table corresponding to a QFP physical entity for a time interval upon detection of a physical entity supporting the utilization statistics for a time interval. The agent destroys a conceptual row from this table corresponding to a QFP physical entity for a time interval upon removal of the QFP host physical entity or it does not receive the utilization statistics update for a certain time period. The time period to wait before deleting an entry from this table would be the discretion of the supporting device.
OBJECT-TYPE    
  SEQUENCE OF  
    CeqfpUtilizationEntry

ceqfpUtilizationEntry 1.3.6.1.4.1.9.9.715.1.1.6.1
A conceptual row in the ceqfpUtilizationTable. There is an entry in this table for each QFP entity by a value of entPhysicalIndex and the supported time interval by a value of ceqfpUtilTimeInterval. The method of utilization data calculation for each interval period can be identified through the respective interval scalar objects. For example the utilizaiton data calculation method for 'fiveSecond' interval can be identified by ceqfpFiveSecondUtilAlgo.
OBJECT-TYPE    
  CeqfpUtilizationEntry  

ceqfpUtilTimeInterval 1.3.6.1.4.1.9.9.715.1.1.6.1.1
This object identifies the time interval for which the utilization statistics being collected. The interval values can be 5 second, 1 minute, etc. as specified in the CiscoQfpTimeInterval.
OBJECT-TYPE    
  CiscoQfpTimeInterval  

ceqfpUtilInputPriorityPktRate 1.3.6.1.4.1.9.9.715.1.1.6.1.2
This object represents the QFP input channel priority packet rate during this interval.
OBJECT-TYPE    
  CiscoQfpPacketRate  

ceqfpUtilInputPriorityBitRate 1.3.6.1.4.1.9.9.715.1.1.6.1.3
This object represents the QFP input channel priority bit rate during this interval.
OBJECT-TYPE    
  CiscoQfpBitRate  

ceqfpUtilInputNonPriorityPktRate 1.3.6.1.4.1.9.9.715.1.1.6.1.4
This object represents the QFP input channel non-priority packet rate during this interval.
OBJECT-TYPE    
  CiscoQfpPacketRate  

ceqfpUtilInputNonPriorityBitRate 1.3.6.1.4.1.9.9.715.1.1.6.1.5
This object represents the QFP input channel non-priority bit rate during this interval.
OBJECT-TYPE    
  CiscoQfpBitRate  

ceqfpUtilInputTotalPktRate 1.3.6.1.4.1.9.9.715.1.1.6.1.6
This object represents the QFP input channel total packet rate during this interval, which includes both priority and non-priority input packet rate.
OBJECT-TYPE    
  CiscoQfpPacketRate  

ceqfpUtilInputTotalBitRate 1.3.6.1.4.1.9.9.715.1.1.6.1.7
This object represents the QFP input channel total bit rate during this interval, which includes both priority and non-priority input bit rate.
OBJECT-TYPE    
  CiscoQfpBitRate  

ceqfpUtilOutputPriorityPktRate 1.3.6.1.4.1.9.9.715.1.1.6.1.8
This object represents the QFP output channel priority packet rate during this interval.
OBJECT-TYPE    
  CiscoQfpPacketRate  

ceqfpUtilOutputPriorityBitRate 1.3.6.1.4.1.9.9.715.1.1.6.1.9
This object represents the QFP output channel priority bit rate during this interval.
OBJECT-TYPE    
  CiscoQfpBitRate  

ceqfpUtilOutputNonPriorityPktRate 1.3.6.1.4.1.9.9.715.1.1.6.1.10
This object represents the QFP output channel non-priority packet rate during this interval.
OBJECT-TYPE    
  CiscoQfpPacketRate  

ceqfpUtilOutputNonPriorityBitRate 1.3.6.1.4.1.9.9.715.1.1.6.1.11
This object represents the QFP output channel non-priority bit rate during this interval.
OBJECT-TYPE    
  CiscoQfpBitRate  

ceqfpUtilOutputTotalPktRate 1.3.6.1.4.1.9.9.715.1.1.6.1.12
This object represents the QFP output channel total packet rate during this interval, which includes both priority and non-priority output packet rate.
OBJECT-TYPE    
  CiscoQfpPacketRate  

ceqfpUtilOutputTotalBitRate 1.3.6.1.4.1.9.9.715.1.1.6.1.13
This object represents the QFP output channel total bit rate during this interval, which includes both priority and non-priority bit rate.
OBJECT-TYPE    
  CiscoQfpBitRate  

ceqfpUtilProcessingLoad 1.3.6.1.4.1.9.9.715.1.1.6.1.14
This object represents the QFP processing load during this interval.
OBJECT-TYPE    
  Gauge32 0..100  

ceqfpMemoryResourceTable 1.3.6.1.4.1.9.9.715.1.1.7
This table maintains the memory resources statistics for each QFP physical entity. An agent creates a conceptual row to this table corresponding to a QFP physical entity and its supported memory resource type upon detection of a physical entity supporting the memory resource statistics for a memory resource type. An agent destroys a conceptual row from this table corresponding to a QFP physical entity and its supported memory resource type upon removal of the QFP host physical entity or it does not receive memory resource statistics update for a certain time period. The time period to wait before deleting an entry from this table would be the discretion of the supporting device.
OBJECT-TYPE    
  SEQUENCE OF  
    CeqfpMemoryResourceEntry

ceqfpMemoryResourceEntry 1.3.6.1.4.1.9.9.715.1.1.7.1
A conceptual row in the ceqfpMemoryResourceTable. There is an entry in this table for each QFP entity by a value of entPhysicalIndex and the supported memory resource type by a value of ceqfpMemoryResType.
OBJECT-TYPE    
  CeqfpMemoryResourceEntry  

ceqfpMemoryResType 1.3.6.1.4.1.9.9.715.1.1.7.1.1
This object indicates the type of the memory resource used by the QFP. This object is one of the indices to uniquely identify the QFP memory resource type.
OBJECT-TYPE    
  CiscoQfpMemoryResource  

ceqfpMemoryResTotal 1.3.6.1.4.1.9.9.715.1.1.7.1.2
This object represents total memory available on this memory resource.
OBJECT-TYPE    
  Gauge32  

ceqfpMemoryResInUse 1.3.6.1.4.1.9.9.715.1.1.7.1.3
This object represents the memory which is currently under use on this memory resource.
OBJECT-TYPE    
  Gauge32  

ceqfpMemoryResFree 1.3.6.1.4.1.9.9.715.1.1.7.1.4
This object represents the memory which is currently free on this memory resource.
OBJECT-TYPE    
  Gauge32  

ceqfpMemoryResLowFreeWatermark 1.3.6.1.4.1.9.9.715.1.1.7.1.5
This object represents lowest free water mark on this memory resource.
OBJECT-TYPE    
  Gauge32  

ceqfpMemoryResRisingThreshold 1.3.6.1.4.1.9.9.715.1.1.7.1.6
This object represents the rising threshold value for this memory resource. A value of zero means that the rising threshold is not supported for this memory resource. The value of this object can not be set to lower than or equal to ceqfpMemoryResFallingThreshold. A rising (ceqfpMemoryResRisingThreshNotif) notification will be generated, whenever the memory resource usage (ceqfpMemoryResInUse) is equal to or greater than this value. After a rising notification is generated, another such notification will not be generated until the ceqfpMemoryResInUse falls below this value and reaches the ceqfpMemoryResFallingThreshold.
OBJECT-TYPE    
  Unsigned32 0..100  

ceqfpMemoryResFallingThreshold 1.3.6.1.4.1.9.9.715.1.1.7.1.7
This object represents the falling threshold value for this memory resource. A value of zero means that the falling threshold is not supported for this memory resource. The value of this object can not be set to higher than or equal to ceqfpMemoryResRisingThreshold. A falling (ceqfpMemoryResRisingThreshNotif) notification will be generated, whenever the memory resource usage (ceqfpMemoryResInUse) is equal to or lesser than this value. After a falling notification is generated, another such notification will not be generated until the ceqfpMemoryResInUse rises above this value and reaches the ceqfpMemoryResRisingThreshold.
OBJECT-TYPE    
  Unsigned32 0..100  

ciscoEntityQfpNotif 1.3.6.1.4.1.9.9.715.1.2
OBJECT IDENTIFIER    

ceqfpMemoryResThreshNotifEnabled 1.3.6.1.4.1.9.9.715.1.2.1
This object controls memory resource rising and falling threshold notification. When this object contains a value 'true', then generation of memory resource threshold notification is enabled. If this object contains a value 'false', then generation of memory resource threshold notification is disabled.
OBJECT-TYPE    
  TruthValue  

ceqfpMemoryResCurrentRisingThresh 1.3.6.1.4.1.9.9.715.1.2.2
This object respresents the current rising threshold value, which triggers the rising threshold notificaiton (ceqfpMemoryResRisingThreshNotif).
OBJECT-TYPE    
  Unsigned32 1..100  

ceqfpMemoryResCurrentFallingThresh 1.3.6.1.4.1.9.9.715.1.2.3
This object respresents the current falling threshold value, which triggers the falling threshold notificaiton (ceqfpMemoryResFallingThreshNotif).
OBJECT-TYPE    
  Unsigned32  

ciscoEntityQfpMIBConform 1.3.6.1.4.1.9.9.715.2
OBJECT IDENTIFIER    

ciscoEntityQfpMIBCompliances 1.3.6.1.4.1.9.9.715.2.1
OBJECT IDENTIFIER    

ciscoEntityQfpMIBComplianceRev1 1.3.6.1.4.1.9.9.715.2.1.1
The compliance statement for CISCO-ENTITY-QFP-MIB
MODULE-COMPLIANCE    

ciscoEntityQfpMIBGroups 1.3.6.1.4.1.9.9.715.2.2
OBJECT IDENTIFIER    

ciscoEntityQfpSystemGroup 1.3.6.1.4.1.9.9.715.2.2.1
This group contains collection of QFP system information.
OBJECT-GROUP    

ciscoEntityQfpUtilizationAlgoGroup 1.3.6.1.4.1.9.9.715.2.2.2
This group contains collection of QFP utilization algorithm objects.
OBJECT-GROUP    

ciscoEntityQfpUtilizationGroup 1.3.6.1.4.1.9.9.715.2.2.3
This group contains collection of QFP utilization information.
OBJECT-GROUP    

ciscoEntityQfpMemoryResourceGroup 1.3.6.1.4.1.9.9.715.2.2.4
This group contains collection of QFP memory resource information.
OBJECT-GROUP    

ciscoEntityQfpNotifGroup 1.3.6.1.4.1.9.9.715.2.2.5
This group contains collection of QFP notifications.
NOTIFICATION-GROUP    

ciscoEntityQfpMemoryResNotifGroup 1.3.6.1.4.1.9.9.715.2.2.6
This group contains memory resource notification control objects.
OBJECT-GROUP    

Defined Objects

CiscoQfpPacketRate  
An estimate of throughput in units of packets per second. The CiscoQfpPacketRate type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value of Counter64. The Counter64 syntax is used for encoding rules.
TEXTUAL-CONVENTION    
  Counter64  

CiscoQfpBitRate  
An estimate of throughput in units of bits per second. The CiscoQfpBitRate type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value of Counter64. The Counter64 syntax is used for encoding rules.
TEXTUAL-CONVENTION    
  Counter64  

CiscoQfpTimeInterval  
An enumerated integer-value describing the available interval values for which the periodic statistics are to be collected. fiveSeconds (1) - Interval to collect last 5 seconds statistics oneMinute(2) - Interval to collect last 1 minute statistics fiveMinutes(3) - Interval to collect last 5 minutes statistics sixtyMinutes(4) - Interval to collect last 60 minutes statistics
TEXTUAL-CONVENTION    
  INTEGER fiveSeconds(1), oneMinute(2), fiveMinutes(3), sixtyMinutes(4)  

CiscoQfpMemoryResource  
An enumerated integer-value describing various memory resources used by the QFP. dram (1) - Dynamic Random Access Memory (DRAM) memory resource
TEXTUAL-CONVENTION    
  INTEGER dram(1)  

CeqfpSystemEntry  
SEQUENCE    
  INTEGER as ceqfpSystemTrafficDirection  
  INTEGER as ceqfpSystemState  
  Counter32 as ceqfpNumberSystemLoads  
  DateAndTime as ceqfpSystemLastLoadTime  

CeqfpUtilizationEntry  
SEQUENCE    
  CiscoQfpTimeInterval as ceqfpUtilTimeInterval  
  CiscoQfpPacketRate as ceqfpUtilInputPriorityPktRate  
  CiscoQfpBitRate as ceqfpUtilInputPriorityBitRate  
  CiscoQfpPacketRate as ceqfpUtilInputNonPriorityPktRate  
  CiscoQfpBitRate as ceqfpUtilInputNonPriorityBitRate  
  CiscoQfpPacketRate as ceqfpUtilInputTotalPktRate  
  CiscoQfpBitRate as ceqfpUtilInputTotalBitRate  
  CiscoQfpPacketRate as ceqfpUtilOutputPriorityPktRate  
  CiscoQfpBitRate as ceqfpUtilOutputPriorityBitRate  
  CiscoQfpPacketRate as ceqfpUtilOutputNonPriorityPktRate  
  CiscoQfpBitRate as ceqfpUtilOutputNonPriorityBitRate  
  CiscoQfpPacketRate as ceqfpUtilOutputTotalPktRate  
  CiscoQfpBitRate as ceqfpUtilOutputTotalBitRate  
  Gauge32 as ceqfpUtilProcessingLoad  

CeqfpMemoryResourceEntry  
SEQUENCE    
  CiscoQfpMemoryResource as ceqfpMemoryResType  
  Gauge32 as ceqfpMemoryResTotal  
  Gauge32 as ceqfpMemoryResInUse  
  Gauge32 as ceqfpMemoryResFree  
  Gauge32 as ceqfpMemoryResLowFreeWatermark  
  Unsigned32 as ceqfpMemoryResRisingThreshold  
  Unsigned32 as ceqfpMemoryResFallingThreshold