
CISCO-HW-MODULE-CONTROL-MIB
File:
CISCO-HW-MODULE-CONTROL-MIB.mib (13431 bytes)
Imported modules
Imported symbols
Defined Objects
| ciscoHwModuleControlMIB |
1.3.6.1.4.1.9.9.714 |
| The MIB module providing configuration and control information for management of hardware modules and components on Cisco devices. The following features are managed: bandwidth oversubscription, clearing of HoL(Head of Line) blocking, etc. Bandwidth oversubscription: a group of ports are said to be operating in bandwidth oversubscription mode if the amount of internal forwarding fabric bandwidth allocated to the group of ports on a switching or routing device is less than the aggregate maximum connection speeds of these ports. Clearing of HoL blocking: refers to the process in which if any port of a port group receives a pause frame from the remote side, it will block packet transmission on all ports of the port group till a packet is delivered to the flow controlled port. If the clearing of HoL blocking feature is disabled, the device will drop packets destined for the jammed ports and continue delivering packets for the other ports. |
| MODULE-IDENTITY |
|
|
|
| chmcOversubModuleEntry |
1.3.6.1.4.1.9.9.714.1.1.1.1 |
| Each entry provides management information for a specific physical module as indicated by the value of entPhysicalIndex, which is capable of providing bandwidth oversubscription feature. |
| OBJECT-TYPE |
|
|
|
| |
ChmcOversubModuleEntry |
|
|
| chmcOversubModuleCapabilities |
1.3.6.1.4.1.9.9.714.1.1.1.1.1 |
| Indicates the attributes of this module with respective to the bandwidth oversubscription feature. oversubConfigModuleLevel(0) - This bit is set if configuration of bandwidth oversubscription is supported at module level. oversubConfigPortGroupLevel(1) - This bit is set if configuration of bandwidth oversubscription is supported at port group level. clearblockConfigPortGroupLevel(2) - This bit is set if configuration of clearing of HoL blocking is supported at port group level. |
| OBJECT-TYPE |
|
|
|
| |
BITS |
oversubConfigModuleLevel(0), oversubConfigPortGroupLevel(1), clearblockConfigPortGroupLevel(2) |
|
| chmcOversubModOversubStatus |
1.3.6.1.4.1.9.9.714.1.1.1.1.2 |
| Specifies the state of the bandwidth oversubscription feature for this module. enabledOnAllPortGroups -- the bandwidth oversubscription feature is enabled on all port groups of this module. disabledOnAllPortGroups -- the bandwidth oversubscription feature is disabled on all port groups of this module. portGroupSpecific -- the bandwidth oversubscription feature is enabled on some port groups of this module while being disabled at the remaining port groups of this module. This value is a read-only value and can not be set on any instance of this object. This object will only be configurable when the instance value of chmcOversubModuleCapabilities of this entry has the 'oversubConfigModuleLevel' bit set to 1. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabledOnAllPortGroups(1), disabledOnAllPortGroups(2), portGroupSpecific(3) |
|
| chmcOversubPortGroupEntry |
1.3.6.1.4.1.9.9.714.1.1.2.1 |
| Each entry contains management information for a specific port group on a specific physical module as indicated by the value of entPhysicalIndex, which is capable of providing bandwidth oversubscription feature. |
| OBJECT-TYPE |
|
|
|
| |
ChmcOversubPortGroupEntry |
|
|
| chmcOversubPortGrpOversubStatus |
1.3.6.1.4.1.9.9.714.1.1.2.1.3 |
| Specifies the state of the bandwidth oversubscription feature on this port group. other - none of the following. This value is a read-only value and can not be set on any instance of this object. enabled - this port group is enabled to operate in bandwidth oversubscription mode. disabled - this port group is disabled to operate in bandwidth oversubscription mode. The first port indicated by the first four bytes of the value of chmcOversubPortGrpIfIndexList of this port group will keep its administrative status and the remaining ports of this port group will be administratively shut down. This object will only be configurable when the instance value of chmcOversubModuleCapabilities for the corresponding module has the 'oversubConfigPortGroupLevel' bit set to 1. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
other(1), enabled(2), disabled(3) |
|
| chmcOversubPortGrpClearBlkStatus |
1.3.6.1.4.1.9.9.714.1.1.2.1.4 |
| Specifies the state of the clearing of HoL blocking feature on this port group. other - none of the following. This value is a read-only value and can not be set on any instance of this object. enabled - the clearing of HoL blocking feature is enabled. disabled - the clearing of HoL blocking feature is disabled. This object will only take effect when the instance value of chmcOversubPortGrpOversubStatus of this entry is 'enabled'. This object will only be configurable when the instance value of chmcOversubPortGrpOversubStatus of this entry is 'enabled' and the instance value of chmcOversubModuleCapabilities for the corresponding module has the 'clearblockConfigPortGroupLevel' bit set to 1. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
other(1), enabled(2), disabled(3) |
|
| ciscoHmcMIBOversubBaseGroup |
1.3.6.1.4.1.9.9.714.2.2.1 |
| A collection of objects providing information about the bandwidth oversubscription and/or clearing of HoL blocking features for hardware modules capable of providing such features. |
| OBJECT-GROUP |
|
|
|
| ciscoHmcMIBOversubPgClearBlkGrp |
1.3.6.1.4.1.9.9.714.2.2.2 |
| A collection of objects describing the clearing of HoL blocking support at port group level for each hardware module capable of providing such feature. |
| OBJECT-GROUP |
|
|
|
Defined Objects
| ChmcOversubModuleEntry |
|
| SEQUENCE |
|
|
|
| |
BITS as chmcOversubModuleCapabilities |
|
|
| |
INTEGER as chmcOversubModOversubStatus |
|
|
| ChmcOversubPortGroupEntry |
|
| SEQUENCE |
|
|
|
| |
Unsigned32 as chmcOversubPortGrpIndex |
|
|
| |
CiscoInterfaceIndexList as chmcOversubPortGrpIfIndexList |
|
|
| |
INTEGER as chmcOversubPortGrpOversubStatus |
|
|
| |
INTEGER as chmcOversubPortGrpClearBlkStatus |
|
|