CISCO-IPSLA-ETHERNET-MIB

File: CISCO-IPSLA-ETHERNET-MIB.mib (116137 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
Q-BRIDGE-MIB IEEE8021-CFM-MIB SNMP-FRAMEWORK-MIB
CISCO-TC CISCO-RTTMON-MIB CISCO-RTTMON-TC-MIB
CISCO-SMI

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Counter32
Gauge32 Unsigned32 TimeTicks
Counter64 MODULE-COMPLIANCE OBJECT-GROUP
TimeStamp StorageType RowStatus
VlanId Dot1agCfmMaintDomainNameType Dot1agCfmMaintDomainName
SnmpAdminString Layer2Cos rttMonCtrlAdminIndex
RttResponseSense RttMonRttType RttMonReactVar
RttMonCtrlIndex RttMonIdLst ciscoMgmt

Defined Objects

ciscoIpSlaEthernetMIB 1.3.6.1.4.1.9.9.585
This MIB module consists of two parts. 1) Auto-Ethernet-CFM Control: |-- ipslaEthernetGrpCtrlTable |-- ipslaEthernetGrpReactTable 2) ethernetJitter Stats: |-- ipslaEtherJitterLatestStatsTable |-- ipslaEtherJitterAggStatsTable The first part defines a mechanism to manage IP SLA Auto-Ethernet-CFM operation. IP SLA is a capability which utilizes active monitoring for network perfomance. It can be used for network troubleshooting, network assessment and health monitoring. IEEE 802.1ag defines Connection Fault Management (CFM) for Ethernet layer. CFM can be used to detect, isolate and report the connectivity faults, and allows discovery and verification of the path through briges and LANs. Auto-Ethernet-CFM operation integrates the capabilities of IP SLA and IEEE 802.1ag. It's capable of discovering all the existing MEPs in a specified VLAN or Ethernet Virtual Connection within a specified maintenance domain. After which, it creates, configures, and schedules an IP SLA operation for each MEP automatically. IP SLA currently supports two types of operations for end-to-end Ethernet connectivity - 'ethernetPing' and 'ethernetJitter'. 'ethernetPing' can be used to monitor the connectivity and measure RTT by sending the regular 802.1ag loopback frame to a particular MEP. 'ethernetJitter' can be used to measure metrics such as RTT, Jitter, frame loss, one-way latency by sending multiple enhanced CFM frames at specified interval to a particular MEP. Without Auto-Ethernet-CFM operation, the two types of operations can also be created, configured, and scheduled manually through CISCO-RTTMON-MIB by specifing the target MEP's identifier in addition to the VLAN or Ethernet Virtual Connection and Maintenance Domain. With Auto-Ethernet-CFM operation, the two types of operations will be created automatically. The Auto-Ethernet-CFM will pass all the values specified in this module to the corresponding objects in CISCO-RTTMON-MIB for each MEP discovered. CISCO-IPSLA-ETHERNET-MIB CISCO-RTTMON-MIB ipslaEthernetGrpCtrlTable -> rttMonCtrlAdminTable | -> rttMonEchoAdminTable ipslaEthernetGrpReactTable -> rttMonReactTable The second part defines a collection of statistics resulting from 'ethernetJitter' operation created either manually or automatically. Glossary: CFM - Connection Fault Management DSAP - Domain Service Access Point: A member of a set of SAPs at which a Maintenance Domain is capable of offering connectivity to systems outside the Maintenance Domain. IP SLA - Cisco IOS IP Service Level Agreements IP SLA operation - Refers to the 'ethernetPing' or 'ethernetJitter' operation supported by IP SLA. MEP - Maintenance association End Point: An actively managed CFM entity, associated with a specific DSAP of a service instance, which can generate and receive CFM PDUs and track any responses. maintenance domain - The network or the part of the network for which faults in connectivity are to be managed. The boundary of a Maintenance Domain is defined by a set of DSAPs, each of which can become a point of connectivity to a service instance. Maintenance Domain Name - The identifier, unique over the domain for which CFM is to protect against accidental concatenation of service instances, of a particular Maintenance Domain. RTT - Round Trip Time SAP - Service Access Point at which a service is offered. service instance - A service instance is a set of SAPs, selected from among the DSAPs defining a Maintenance Domain, such that a Data.Request primitive presented to one SAP can result in a Data.Indication primitive occurring at one or more of the other SAPs in the set. It corresponds to a VLAN or an Ethernet Virtual Connection. TLV - Stands for Type, Length, Value, and denotes a method of encoding variable-length and/or optional information in a PDU. TLVs are not aligned to any particular word or octet boundary. TLVs follow each other with no padding between TLVs. VLAN - Virtual Local Area Network: A subset of the active topology of a Bridged Local Area Network. Associated with each VLAN is a VLAN Identifier. REFERENCE: IEEE 802.1ag Draft 6.0 'Virtual Briged Local Area Networks - Amendments 5: Connectivity Fault Management' July 2006
MODULE-IDENTITY    

ciscoIpSlaEthernetMIBNotifs 1.3.6.1.4.1.9.9.585.0
OBJECT IDENTIFIER    

ciscoIpSlaEthernetMIBObjects 1.3.6.1.4.1.9.9.585.1
OBJECT IDENTIFIER    

ipslaEthernetGrpCtrl 1.3.6.1.4.1.9.9.585.1.1
OBJECT IDENTIFIER    

ipslaEthernetGrpCtrlTable 1.3.6.1.4.1.9.9.585.1.1.1
This table contains Auto-Ethernet-CFM control data. When a row transition to the 'active' state, the IP SLA agent will discover all the MEPs inside the specified VLAN and maintenance domain and create IP SLA ethernet operations based on the value of ipslaEthernetGrpCtrlRttType for each MEP. All the values in this table will be passed to the corresponding objects in the rttMonCtrlAdminTable and rttMonEchoAdminTable of CISCO-RTTMON-MIB so that each IP SLA Ethernet operation will have the same configuration as specified for Auto-Ethernet-CFM. - Objects in this table - Corresponding objects in rttMonCtrlAdminTable ipslaEthernetGrpCtrlStatus rttMonCtrlAdminStatus ipslaEthernetGrpCtrlRttType rttMonCtrlAdminRttType ipslaEthernetGrpCtrlOwner rttMonCtrlAdminOwner ipslaEthernetGrpCtrlTag rttMonCtrlAdminTag ipslaEthernetGrpCtrlThreshold rttMonCtrlAdminThreshold ipslaEthernetGrpCtrlTimeout rttMonCtrlAdminTimeout - Objects in this table - Corresponding objects in rttMonEchoAdminTable ipslaEthernetGrpCtrlVLAN rttMonEchoAdminTargetVLAN ipslaEthernetGrpCtrlDomainName rttMonEchoAdminTargetDomainName ipslaEthernetGrpCtrlReqDataSize rttMonEchoAdminPktDataRequestSize ipslaEthernetGrpCtrlCOS rttMonEchoAdminEthernetCOS ipslaEthernetGrpCtrlInterval rttMonEchoAdminInterval ipslaEthernetGrpCtrlNumFrames rttMonEchoAdminNumPackets ipslaEthernetGrpCtrlEVC rttMonEchoAdminTargetEVC
OBJECT-TYPE    
  SEQUENCE OF  
    IpslaEthernetGrpCtrlEntry

ipslaEthernetGrpCtrlEntry 1.3.6.1.4.1.9.9.585.1.1.1.1
A collection of objects that define a conceptual Auto-Ethernet-CFM control row. The following objects must be specified in order to create this conceptual row. - ipslaEthernetGrpCtrlStatus - ipslaEthernetGrpCtrlRttType The following objects must be specified in order to activate this conceptual row. - ipslaEthernetGrpCtrlVLAN OR - ipslaEthernetGrpCtrlEVC - ipslaEthernetGrpCtrlDomainName - ipslaEthernetGrpSchedulePeriod - ipslaEthernetGrpScheduleRttStartTime This conceptual row can be delete at any time by set the ipslaEthernetGrpCtrlStatus to 'destroy'. When this row is deleted, All the IP SLA operations created by this row will be destroyed.
OBJECT-TYPE    
  IpslaEthernetGrpCtrlEntry  

ipslaEthernetGrpCtrlIndex 1.3.6.1.4.1.9.9.585.1.1.1.1.1
This object indicates a row in the ipslaEthernetGrpCtrlTable. This value is a pseudo-random number selected by the management station when creating a row via the ipslaEthernetGrpCtrlStatus object. For easy management, user can select range of numbers for different maintenance domain. For instance, the ipslaEthernetGrpCtrlIndex 1-100 will be used for Domain_A, 101-200 will be used for Domain_B. If the pseudo-random number is already in use an 'inconsistentValue' return code will be returned when set operation is attempted.
OBJECT-TYPE    
  RttMonCtrlIndex  

ipslaEthernetGrpCtrlStatus 1.3.6.1.4.1.9.9.585.1.1.1.1.2
This object specifies the status of Auto-Ethernet-CFM control row. Following objects must be specified in order for this object to become active. - ipslaEthernetGrpCtrlRttType - ipslaEthernetGrpCtrlVLAN OR - ipslaEthernetGrpCtrlEVC - ipslaEthernetGrpCtrlServiceInsType - ipslaEthernetGrpCtrlDomainName - ipslaEthernetGrpSchedulePeriod - ipslaEthernetGrpScheduleRttStartTime All other objects can assume default values. The following objects cannot be modified after creating the Auto-Ethernet-CFM conceptual row. - ipslaEthernetGrpCtrlRttType - ipslaEthernetGrpCtrlVLAN OR - ipslaEthernetGrpCtrlEVC - ipslaEthernetGrpCtrlDomainName - ipslaEthernetGrpCtrlServiceInsType The following objects can be modified even after creating the Auto-Ethernet-CFM conceptual row by setting this object to 'notInService' - All other writable objects in ipslaEthernetGrpCtrlTable except ipslaEthernetGrpCtrlRttType, ipslaEthernetGrpCtrlVLAN, ipslaEthernetGrpCtrlDomainName, ipslaEthernetGrpCtrlEVC and ipslaEthernetGrpCtrlServiceInsType - Objects in the ipslaEthernetGrpScheduleTable. The following objects can be modified as needed without setting this object to 'notInService' even after creating the Auto-Ethernet-CFM conceptual row. - Objects in ipslaEthernetGrpReactTable. This object can be set to 'destroy' from any value at any time. When this object is set to 'destroy' it will stop and destroy all the IP SLA operations created by this Auto-Ethernet-CFM before destroying Auto-Ethernet-CFM control row.
OBJECT-TYPE    
  RowStatus  

ipslaEthernetGrpCtrlStorageType 1.3.6.1.4.1.9.9.585.1.1.1.1.3
This object specifies how the SNMP entity stores the data contained by the corresponding conceptual row. This object can be set to either 'volatile' or 'nonVolatile'. Other values are not applicable for this conceptual row and are not supported.
OBJECT-TYPE    
  StorageType  

ipslaEthernetGrpCtrlRttType 1.3.6.1.4.1.9.9.585.1.1.1.1.4
The type of IP SLA operation to be created by this Auto-Ethernet-CFM. This value can only be set to type 'ethernetPing' and 'ethernetJitter'. 'ethernetPing' operation sends the regular 802.1ag loopback frame to the target MEP to monitor the connectivity and perform delay analysis. 'ethernetJitter'sends multiple enhanced CFM frames at a specified interval to the target MEP to measure metrics such as RTT, jitter, frame loss, one-way latency and so on. This value must be set before setting any other parameter configuration of an Auto-Ethernet-CFM.
OBJECT-TYPE    
  RttMonRttType  

ipslaEthernetGrpCtrlOwner 1.3.6.1.4.1.9.9.585.1.1.1.1.5
A string which used by a managing application to identify the entity that created this Auto-Ethernet-CFM.
OBJECT-TYPE    
  SnmpAdminString SIZE(0..255)  

ipslaEthernetGrpCtrlTag 1.3.6.1.4.1.9.9.585.1.1.1.1.6
A string which used by a managing application to identify the target VLAN and maintenance domain of this Auto-Ethernet-CFM.
OBJECT-TYPE    
  SnmpAdminString SIZE(0..255)  

ipslaEthernetGrpCtrlThreshold 1.3.6.1.4.1.9.9.585.1.1.1.1.7
This object specifies the threshold value of a particular object. This value will be examined for each IP SLA operations created by the Auto-Ethernet-CFM. For 'ethernetPing', if the value of rttMonLatestRttOperCompletionTime is greater than this value, the 'overThreshold' will be reported through rttMonLatestRttOperSense defined in CISCO-RTTMON-MIB. For 'ethernetJitter', if the value of ipslaEtherJitterLatestAvgJitter value is greater than this value, the 'overThreshold' will be reported through ipslaEtherJitterLatestSense defined this module.
OBJECT-TYPE    
  Unsigned32 0..2147483647  

ipslaEthernetGrpCtrlTimeout 1.3.6.1.4.1.9.9.585.1.1.1.1.8
Specifies the duration to wait for an IP SLA operation created by this Auto-Ethernet-CFM to complete. For 'ethernetPing', if the value of rttMonLatestRttOperCompletionTime is greater than this value, the 'timeout' will be reported through rttMonLatestRttOperSense defined in CISCO-RTTMON-MIB. For 'ethernetJitter', if all the frames sent to target MEP have not been recievied within this duration, the 'timeout' will be reported through ipslaEtherJitterLatestSense defined this module. The value of this object cannot be set to a value which would specify a duration exceeding ipslaEthernetGrpScheduleFrequency.
OBJECT-TYPE    
  Unsigned32 0..604800000  

ipslaEthernetGrpCtrlProbeList 1.3.6.1.4.1.9.9.585.1.1.1.1.9
This object indicates the identifiers of the IP SLA operations that are created by the Auto-Ethernet-CFM. The identifier will be stored in rttMonCtrlAdminIndex defined in CISCO-RTTMON-MIB for each IP SLA operation.
OBJECT-TYPE    
  RttMonIdLst  

ipslaEthernetGrpCtrlVLAN 1.3.6.1.4.1.9.9.585.1.1.1.1.10
This object specifies the identifier of VLAN for which the Auto-Ethernet-CFM operation will be used. It is an unique identifier for a service instance within a Maintenance Domain specified by ipslaEthernetGrpCtrlDomainName. The Auto-Ethernet-CFM will find all the MEPs participating in this VLAN and create IP SLA operations for each MEP corresponding to value specified in ipslaEthernetGrpCtrlRttType. The value of this object is in effect only when the value of ipslaEthernetGrpCtrlServiceInsType is set to 'vlan'.
OBJECT-TYPE    
  VlanId  

ipslaEthernetGrpCtrlDomainNameType 1.3.6.1.4.1.9.9.585.1.1.1.1.11
This object specifies the type of maintenance domain name to be used by the Auto-Ethernet-CFM operation. This object can only be set to the following values: 'none'(1) 'charString'(4) Other values are not supported. Value 'none' means that the ipslaEthernetGrpCtrlDomainName has not been specified.
OBJECT-TYPE    
  Dot1agCfmMaintDomainNameType  

ipslaEthernetGrpCtrlDomainName 1.3.6.1.4.1.9.9.585.1.1.1.1.12
This object specifies the maintenance domain name to be used by the Auto-Ethernet-CFM operation. The Auto-Ethernet-CFM operation discovers all the MEPs participating in the VLAN specified by ipslaEthernetGrpCtrlVLAN within this maintenance domain and create IP SLA operations for each MEP corresponding to value specified in ipslaEthernetGrpCtrlRttType. As long as the value of this object is specified, the value of ipslaEthernetGrpCtrlDomainNameType must be set to 'charString'.
OBJECT-TYPE    
  Dot1agCfmMaintDomainName  

ipslaEthernetGrpCtrlReqDataSize 1.3.6.1.4.1.9.9.585.1.1.1.1.13
This object specifies the padding that needs to be inserted into each ethernet frame of the IP SLA operation. The total ethernet frame size of the IP SLA operation is: CFM_header + TLVs + si_length + dm_length + padding size where dm_length = number of octets of the maintenance domain name si_length = number of octets of the service instance name CFM_header = 8 octets TLVs = 60 octets for 'ethernetPing' 45 octets for 'ethernetJitter' If the total frame size exceeds 1500, only 1500 will be sent to the target MEP.
OBJECT-TYPE    
  Unsigned32 0..1400  

ipslaEthernetGrpCtrlMPIDExLst 1.3.6.1.4.1.9.9.585.1.1.1.1.14
This object specifies the identifiers of the MEPs that will be excluded when create IP SLA operations by Auto-Ethernet-CFM operation.
OBJECT-TYPE    
  RttMonIdLst  

ipslaEthernetGrpCtrlCOS 1.3.6.1.4.1.9.9.585.1.1.1.1.15
This object specifies the Class Of Service field in an Ethernet frame header.
OBJECT-TYPE    
  Layer2Cos  

ipslaEthernetGrpCtrlInterval 1.3.6.1.4.1.9.9.585.1.1.1.1.16
This value specifies the inter-frame delay between Ethernet frames that need to be transmitted to the target MEPs. This object is applicable to 'ethernetJitter' operation only.
OBJECT-TYPE    
  Unsigned32 1..60000  

ipslaEthernetGrpCtrlNumFrames 1.3.6.1.4.1.9.9.585.1.1.1.1.17
This value specifies the number of Ethernet frames that need to be transmitted to the target MEPs. This object is applicable to 'ethernetJitter' operation only.
OBJECT-TYPE    
  Unsigned32 1..60000  

ipslaEthernetGrpScheduleRttStartTime 1.3.6.1.4.1.9.9.585.1.1.1.1.18
This object specifies the time when this conceptual row will become 'active'. ipslaEthernetGrpSchedulePeriod object must be specified before setting this object. When sysUpTime equals this value, this object will cause the conceptual Auto-Ethernet-CFM row transmit to 'active'and start to discover the existing MEPs. Meanwhile the IP SLA operations will be created for each discovered MEP, and rttMonCtrlAdminStatus of each IP SLA operation will transmit to 'active'. If this object has value as 1, the conceptual Auto-Ethernet-CFM row will transmit to 'active' right now. Value of 0 puts this conceptual row in pending state.
OBJECT-TYPE    
  TimeTicks  

ipslaEthernetGrpSchedulePeriod 1.3.6.1.4.1.9.9.585.1.1.1.1.19
Specifies the time duration over which all the IP SLA operations created by the current Auto-Ethernet-CFM have to be scheduled. For instance, if there are three MEPs discovered, there will be three IP SLA operations created. If this object is set to 30, ipslaEthernetGrpScheduleRttStartTime is set to T, the start time of three operations will be spreaded evenly within 30 seconds, i.e. start time: T+0 -------- T+9 ----------T+19 operation1 operation2 operation3 This object must be set first before setting ipslaEthernetGrpScheduleRttStartTime.
OBJECT-TYPE    
  Unsigned32 1..604800  

ipslaEthernetGrpScheduleFrequency 1.3.6.1.4.1.9.9.585.1.1.1.1.20
Specifies the duration between initiating each IP SLA operation created by the Auto-Ethernet-CFM. Take above example, if the ipslaEthernetGrpScheduleFrequency is set to 60, then the start time of each IP SLA operation like: start time: T+0 -------- T+9 ----------T+19----- operation1 operation2 operation3 start again: --T+60-------- T+69 ----------T+79-- operation1 operation2 operation3 start 3rd time:--T+120-------- T+129 ----------T+139-- operation1 operation2 operation3 This object cannot be set to a value which would be a shorter duration than ipslaEthernetGrpCtrlTimeout. The default value of this object is the value set to ipslaEthernetGrpSchedulePeriod. This value will be passed to rttMonCtrlAdminFrequency for all the IP SLA operations created by the Auto-Ethernet-CFM.
OBJECT-TYPE    
  Unsigned32 1..604800  

ipslaEthernetGrpCtrlEVC 1.3.6.1.4.1.9.9.585.1.1.1.1.21
This object specifies the Ethernet Virtual Connection for which the Auto-Ethernet-CFM operation will be used. It is an unique identifier for a service instance within a Maintenance Domain specified by ipslaEthernetGrpCtrlDomainName. The Auto-Ethernet-CFM will find all the MEPs participating in this Ethernet Virtual Connection and create IP SLA operations for each MEP corresponding to value specified in ipslaEthernetGrpCtrlRttType. The value of this object is in effect only when the value of ipslaEthernetGrpCtrlServiceInsType is set to 'evc'.
OBJECT-TYPE    
  SnmpAdminString SIZE(0..100)  

ipslaEthernetGrpCtrlServiceInsType 1.3.6.1.4.1.9.9.585.1.1.1.1.22
This object specifies the type of service instance to be used by the Auto-Ethernet-CFM operation. When this object is set to value 'vlan', ipslaEthernetGrpCtrlVLAN must be set, and the value of ipslaEthernetGrpCtrlVLAN will be used by the Auto-Ethernet-CFM to discover the participating MEPs. When this object is set to value 'evc', ipslaEthernetGrpCtrlEVC must be set, and the value of ipslaEthernetGrpCtrlEVC will be used by the Auto-Ethernet-CFM to discover the participating MEPs.
OBJECT-TYPE    
  INTEGER vlan(1), evc(2)  

ipslaEthernetGrpReactTable 1.3.6.1.4.1.9.9.585.1.1.2
A table that contains the reaction configurations for Auto-Ethernet-CFM operation. The reaction configuration specifies the network perfomance parameter needs to be monitored, the threshold for the parameter, the type of threshold violation that will trigger a reaction, and how to react upon a threshold being violated. This allows for proactive monitoring in an environment where user can be alerted to potential network problems, rather than having to manually examine data. Each conceptual row in ipslaEthernetGrpReactTable corresponds to a reaction configured for a corresponding Auto-Ethernet-CFM operation. Each Auto-Ethernet-CFM operation can have multiple parameters monitored and hence there can be multiple reaction configuration rows for a particular Auto-Ethernet-CFM operation. The reaction configurations in this table for a particular Auto-Ethernet-CFM operation will be passed to the corresponding objects in rttMonReactTable of CISCO-RTTMON-MIB for all the IP SLA operations created by this Auto-Ethernet-CFM. This makes the IP SLA operation capable of reacting to certain measured network condition such as long round trip delay, big jitter, etc., by generating a notification to a network management application based on defined thresholds. - Objects in this table - Corresponding objects in rttMonReactTable ipslaEthernetGrpReactConfigIndex rttMonReactConfigIndex ipslaEthernetGrpReactVar rttMonReactVar ipslaEthernetGrpReactThresholdType rttMonReactThresholdType ipslaEthernetGrpReactThresholdRising rttMonReactThresholdRising ipslaEthernetGrpReactThresholdFalling rttMonReactThresholdFalling ipslaEthernetGrpReactThresholdCountX rttMonReactThresholdCountX ipslaEthernetGrpReactThresholdCountY rttMonReactThresholdCountY ipslaEthernetGrpReactActionType rttMonReactActionType ipslaEthernetGrpReactStatus rttMonReactStatus This table is coupled with ipslaEthernetGrpCtrlTable. When an entry in the ipslaEthernetGrpCtrlTable is destroyed, the corresponding entries in this table will be destroyed too.
OBJECT-TYPE    
  SEQUENCE OF  
    IpslaEthernetGrpReactEntry

ipslaEthernetGrpReactEntry 1.3.6.1.4.1.9.9.585.1.1.2.1
A collection of objects that define a conceptual Auto-Ethernet-CFM reaction configuration row. In order to create this conceptual row, ipslaEthernetGrpReactStatus must be set to 'createAndGo' and ipslaEthernetGrpReactVar must be specified. This conceptual row can be deleted at any time by set ipslaEthernetGrpReactStatus to 'destroy'. When this row is deleted, the corresponding reaction configuration of all the IP SLA operations are deleted.
OBJECT-TYPE    
  IpslaEthernetGrpReactEntry  

ipslaEthernetGrpReactConfigIndex 1.3.6.1.4.1.9.9.585.1.1.2.1.1
This object along with ipslaEthernetGrpCtrlEntry identifies a particular reaction-configuration for a particular Auto-Ethernet-CFM operation. This is a pseudo-random number selected by the management station when creating a row via the ipslaEthernetGrpReactStatus. If the pseudo-random number is already in use an 'inconsistentValue' return code will be returned when set operation is attempted.
OBJECT-TYPE    
  RttMonCtrlIndex  

ipslaEthernetGrpReactStatus 1.3.6.1.4.1.9.9.585.1.1.2.1.2
This objects specifies the status of the conceptual Auto-Ethernet-CFM reaction control row. Only 'createAndGo' and 'destroy' operations are permitted on the row. In order for this object to become 'active', ipslaEthernetGrpReactVar must be defined. All other objects assume the default value. When this object is in 'active' state, all the writable objects except ipslaEthernetGrpReactVar can be modified. When this object moves to 'active' state, the rttMonReactStatus of the individual IP SLA operations moves to 'active' state, thus the performance parameter specified in the reaction configuration is monitored for each IP SLA operation and the notifications are generated when the threshold violation takes place. This object can be set to 'destroy' from any value at any time. When this object is set to 'destroy', the reaction configuration of both Auto-Ethernet-CFM operation and IP SLA operations are removed.
OBJECT-TYPE    
  RowStatus  

ipslaEthernetGrpReactStorageType 1.3.6.1.4.1.9.9.585.1.1.2.1.3
This object specifies how the SNMP entity stores the data contained by the corresponding conceptual row. This object can be set to either 'volatile' or 'nonVolatile'. Other values are not applicable for this conceptual row and are not supported.
OBJECT-TYPE    
  StorageType  

ipslaEthernetGrpReactVar 1.3.6.1.4.1.9.9.585.1.1.2.1.4
This object specifies the performance parameter that will be monitored by the IP SLA operations which are created via Auto-Ethernet-CFM operation. The performance parameters that are valid to both 'ethernetJitter' and 'ethernetPing' include: - 'connectionLoss' - 'rtt' - 'timeout' The performance parameters that are only valid to 'ethernetJitter' include: - 'jitterSDAvg' - 'jitterDSAvg' - 'jitterAvg' - 'maxOfPositiveSD' - 'maxOfNegativeSD' - 'maxOfPositiveDS' - 'maxOfNegativeDS' - 'packetLateArrival' - 'packetLossDS' - 'packetLossSD' - 'packetOutOfSequence' - 'packetMIA'
OBJECT-TYPE    
  RttMonReactVar  

ipslaEthernetGrpReactThresholdType 1.3.6.1.4.1.9.9.585.1.1.2.1.5
This object specifies the type of threshold violation that will trigger an notification. The notification will be sent accordingly only when the object rttMonReactOccurred which is defined in CISCO-RTTMON-MIB for IP SLA operation is set to 'true' or 'false'. 'never' - rttMonReactOccurred is never set 'immediate' - rttMonReactOccurred is set to 'true' when the value of parameter for which reaction is configured ( e.g. rtt, jitterAvg) violates the threshold. Conversely, rttMonReactOccurred is set to 'false' when the parameter ( e.g. rtt, jitterAvg) is below the threshold limits. 'consecutive'- rttMonReactOccurred is set to true when the value of parameter for which reaction is configured ( e.g. rtt, jitterAvg) violates the threshold for configured consecutive times. Conversely, rttMonReactOccurred is set to false when the value of parameter ( e.g. rtt, jitterAvg) is below the threshold limits for the same number of consecutive operations. 'xOfy' - rttMonReactOccurred is set to true when x ( as specified by ipslaEthernetGrpReactThresholdCountX ) out of the last y ( as specified by ipslaEthernetGrpReactThresholdCountY ) times the value of parameter for which the reaction is configured ( e.g. rtt, jitterAvg) violates the threshold. Conversely, it is set to false when x, out of the last y times the value of parameter ( e.g. rtt, jitterAvg) is below the threshold limits. 'average' - rttMonReactOccurred is set to true when the average (ipslaEthernetGrpReactThresholdCountX times ) value of parameter for which reaction is configured ( e.g. rtt, jitterAvg) violates the threshold condition. Conversely, it is set to false when the average value of parameter ( e.g. rtt, jitterAvg).
OBJECT-TYPE    
  INTEGER never(1), immediate(2), consecutive(3), xOfy(4), average(5)  

ipslaEthernetGrpReactThresholdRising 1.3.6.1.4.1.9.9.585.1.1.2.1.6
This object specifies the higher threshold limit. If the value of monitored parameter ( e.g rtt, jitterAvg, packetLossSD etc ) rises above this limit and if the condition specified in ipslaEthernetGrpReactThresholdType are satisfied, a notification is generated. Default value of ipslaEthernetGrpReactThresholdRising for 'rtt' is 5000. 'jitterAvg' is 100. 'jitterSDAvg' is 100. 'jitterDSAvg' is 100. 'maxOfPositiveSD' is 10000. 'maxOfNegativeSD' is 10000. 'maxOfPositiveDS' is 10000. 'maxOfNegativeDS' is 10000. 'packetLossSD' is 10000. 'packetLossDS' is 10000. 'packetMIA' is 10000. 'packetLateArrival' is 10000. 'packetOutOfSequence' is 10000. This object is not applicable if the ipslaEthernetGrpReactVar is 'timeout' or 'connectionLoss'. For 'timeout' and 'connectionLoss', the default value will be 0.
OBJECT-TYPE    
  Unsigned32 0..2147483647  

ipslaEthernetGrpReactThresholdFalling 1.3.6.1.4.1.9.9.585.1.1.2.1.7
This object specifies the lower threshold limit. If the value of monitored parameter ( e.g rtt, jitterAvg, packetLossSD etc ) falls below this limit and if the condition specified in ipslaEthernetGrpReactThresholdType are satisfied, a notification is generated. Default value of ipslaEthernetGrpReactThresholdFalling for 'rtt' is 3000. 'jitterAvg' is 100. 'jitterSDAvg' is 100. 'jitterDSAvg' is 100. 'maxOfPositiveSD' is 10000. 'maxOfNegativeSD' is 10000. 'maxOfPositiveDS' is 10000. 'maxOfNegativeDS' is 10000. 'packetLossSD' is 10000. 'packetLossDS' is 10000. 'packetMIA' is 10000. 'packetLateArrival' is 10000. 'packetOutOfSequence' is 10000. This object is not applicable if the ipslaEthernetGrpReactVar is 'timeout' or 'connectionLoss'. For 'timeout' and 'connectionLoss', the default value will be 0.
OBJECT-TYPE    
  Unsigned32 0..2147483647  

ipslaEthernetGrpReactThresholdCountX 1.3.6.1.4.1.9.9.585.1.1.2.1.8
If ipslaEthernetGrpReactThresholdType value is 'xOfy', this object specifies the 'x' value. If ipslaEthernetGrpReactThresholdType value is 'consecutive', this object specifies the number of consecutive occurrences that needs threshold violation before setting rttMonReactOccurred as 'true'. If ipslaEthernetGrpReactThresholdType value is 'average', this object specifies the number of samples that needs be considered for calculating average. This object has no meaning if ipslaEthernetGrpReactThresholdType has value of 'never' and 'immediate'.
OBJECT-TYPE    
  Unsigned32 1..16  

ipslaEthernetGrpReactThresholdCountY 1.3.6.1.4.1.9.9.585.1.1.2.1.9
This object specifies the 'y' value of the xOfy condition if ipslaEthernetGrpReactThresholdType is 'xOfy'. For other values of ipslaEthernetGrpReactThresholdType, this object is not applicable.
OBJECT-TYPE    
  Unsigned32 1..16  

ipslaEthernetGrpReactActionType 1.3.6.1.4.1.9.9.585.1.1.2.1.10
This object specifies what type of reaction to generate if an IP SLA operation violates one of the watched conditions (specified in ipslaEthernetGrpReactVar): 'none' - no reaction is generated. 'notification' - a notification is generated.
OBJECT-TYPE    
  INTEGER none(1), notification(2)  

ipslaEthernetStats 1.3.6.1.4.1.9.9.585.1.2
OBJECT IDENTIFIER    

ipslaEtherJitterAggStatsTable 1.3.6.1.4.1.9.9.585.1.2.1
The 'ethernetJitter' statistics table contains summarized information of the results for a conceptual control row. A rolling accumulated history of this information is maintained in a series of hourly 'group(s)'. When ipslaEtherJAggStatsStartTimeId groups exceeds the rttMonStatisticsAdminNumHourGroups value, the oldest corresponding hourly group will be deleted and will be replaced with the new ipslaEtherJAggStatsStartTimeId hourly group.
OBJECT-TYPE    
  SEQUENCE OF  
    IpslaEtherJitterAggStatsEntry

ipslaEtherJitterAggStatsEntry 1.3.6.1.4.1.9.9.585.1.2.1.1
This entry contains the objects which accumulate the results of a series of 'ethernetJitter' operations over a 60 minute time period or a time period stored in rttMonScheduleAdminRttLife, whichever is smaller. An entry is created only if when the following objects are valid. - rttMonCtrlAdminRttType - rttMonEchoAdminProtocol The entry will start to collect data when rttMonCtrlAdminStatus is in 'active' state. The entry will be removed when the rttMonCtrlAdminStatus is changed to 'destroy' state.
OBJECT-TYPE    
  IpslaEtherJitterAggStatsEntry  

ipslaEtherJAggStatsStartTimeId 1.3.6.1.4.1.9.9.585.1.2.1.1.1
The value of sysUpTime at the time when this row was created.
OBJECT-TYPE    
  TimeStamp  

ipslaEtherJAggMeasuredCmpletions 1.3.6.1.4.1.9.9.585.1.2.1.1.2
The number of Ethernet jitter operations that have completed successfully.
OBJECT-TYPE    
  Counter32  

ipslaEtherJAggMeasuredOvThrshlds 1.3.6.1.4.1.9.9.585.1.2.1.1.3
The number of Ethernet jitter operations that violate jitterAvg threshold which is defined in RttMonReactVar.
OBJECT-TYPE    
  Counter32  

ipslaEtherJAggMeasuredNumRTTs 1.3.6.1.4.1.9.9.585.1.2.1.1.4
The number of RTTs that are successfully measured.
OBJECT-TYPE    
  Counter32  

ipslaEtherJAggMeasuredRTTSums 1.3.6.1.4.1.9.9.585.1.2.1.1.5
The sum of RTTs that are successfully measured for this ipslaEtherJAggMeasuredStartTimeId hourly group. The number of the successfully measured RTT is stored in the ipslaEtherJAggMeasuredNumRTTs.
OBJECT-TYPE    
  Counter32  

ipslaEtherJAggMeasuredRTTSum2Ls 1.3.6.1.4.1.9.9.585.1.2.1.1.6
The sum of squares of RTTs that are successfully measured (low order 32 bits).
OBJECT-TYPE    
  Counter32  

ipslaEtherJAggMeasuredRTTSum2Hs 1.3.6.1.4.1.9.9.585.1.2.1.1.7
The sum of squares of RTTs that are successfully measured (high order 32 bits).
OBJECT-TYPE    
  Counter32  

ipslaEtherJAggMeasuredRTTMin 1.3.6.1.4.1.9.9.585.1.2.1.1.8
The minimum of RTTs that were successfully measured.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMeasuredRTTMax 1.3.6.1.4.1.9.9.585.1.2.1.1.9
The maximum of RTTs that were successfully measured.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMeasuredMinPosSD 1.3.6.1.4.1.9.9.585.1.2.1.1.10
The minimum of absolute values of all positive jitter values for frames sent from source to destination.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMeasuredMaxPosSD 1.3.6.1.4.1.9.9.585.1.2.1.1.11
The maximum of absolute values of all positive jitter values for frames sent from source to destination.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMeasuredNumPosSDs 1.3.6.1.4.1.9.9.585.1.2.1.1.12
The number of all positive jitter values for frames sent from source to destination.
OBJECT-TYPE    
  Counter32  

ipslaEtherJAggMeasuredSumPosSDs 1.3.6.1.4.1.9.9.585.1.2.1.1.13
The sum of all positive jitter values for frames sent from source to destination. The number of such values is stored in ipslaEtherJAggMeasuredNumPosSDs.
OBJECT-TYPE    
  Counter32  

ipslaEtherJAggMeasuredSum2PSDLs 1.3.6.1.4.1.9.9.585.1.2.1.1.14
The sum of square of all positive jitter values for frames sent from source to destination (low order 32 bits).
OBJECT-TYPE    
  Counter32  

ipslaEtherJAggMeasuredSum2PSDHs 1.3.6.1.4.1.9.9.585.1.2.1.1.15
The sum of square of all positive jitter values for frames sent from source to destination (high order 32 bits).
OBJECT-TYPE    
  Counter32  

ipslaEtherJAggMeasuredMinNegSD 1.3.6.1.4.1.9.9.585.1.2.1.1.16
The minimum of all negative jitter values for frames sent from source to destination.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMeasuredMaxNegSD 1.3.6.1.4.1.9.9.585.1.2.1.1.17
The maximum of all negative jitter values for frames sent from source to destination.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMeasuredNumNegSDs 1.3.6.1.4.1.9.9.585.1.2.1.1.18
The number of all negative jitter values for frames sent from source to destination.
OBJECT-TYPE    
  Counter32  

ipslaEtherJAggMeasuredSumNegSDs 1.3.6.1.4.1.9.9.585.1.2.1.1.19
The sum of all negative jitter values for frames sent from source to destination. The number of such values is stored in ipslaEtherJAggMeasuredNumNegSDs.
OBJECT-TYPE    
  Counter32  

ipslaEtherJAggMeasuredSum2NSDLs 1.3.6.1.4.1.9.9.585.1.2.1.1.20
The sum of square of all negative jitter values for frames sent from source to destination (low order 32 bits).
OBJECT-TYPE    
  Counter32  

ipslaEtherJAggMeasuredSum2NSDHs 1.3.6.1.4.1.9.9.585.1.2.1.1.21
The sum of square of all negative jitter values for frames sent from source to destination (high order 32 bits).
OBJECT-TYPE    
  Counter32  

ipslaEtherJAggMeasuredMinPosDS 1.3.6.1.4.1.9.9.585.1.2.1.1.22
The minimum of all positive jitter values for frames sent from destination to source.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMeasuredMaxPosDS 1.3.6.1.4.1.9.9.585.1.2.1.1.23
The maximum of all positive jitter values for frames sent from destination to source.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMeasuredNumPosDSes 1.3.6.1.4.1.9.9.585.1.2.1.1.24
The number of all positive jitter values for frames sent from destination to source.
OBJECT-TYPE    
  Counter32  

ipslaEtherJAggMeasuredSumPosDSes 1.3.6.1.4.1.9.9.585.1.2.1.1.25
The sum of all positive jitter values for frames sent from destination to source. The number of such values is stored in ipslaEtherJAggMeasuredNumPosDSes.
OBJECT-TYPE    
  Counter32  

ipslaEtherJAggMeasuredSum2PDSLs 1.3.6.1.4.1.9.9.585.1.2.1.1.26
The sum of squares of all positive jitter values for frames sent from destination to source (low order 32 bits).
OBJECT-TYPE    
  Counter32  

ipslaEtherJAggMeasuredSum2PDSHs 1.3.6.1.4.1.9.9.585.1.2.1.1.27
The sum of squares of all positive jitter values for frames sent from destination to source (high order 32 bits).
OBJECT-TYPE    
  Counter32  

ipslaEtherJAggMeasuredMinNegDS 1.3.6.1.4.1.9.9.585.1.2.1.1.28
The minimum of all negative jitter values for frames sent from destination to source.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMeasuredMaxNegDS 1.3.6.1.4.1.9.9.585.1.2.1.1.29
The maximum of all negative jitter values for frames sent from destination to source.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMeasuredNumNegDSes 1.3.6.1.4.1.9.9.585.1.2.1.1.30
The number of all negative jitter values for frames sent from destination to source.
OBJECT-TYPE    
  Counter32  

ipslaEtherJAggMeasuredSumNegDSes 1.3.6.1.4.1.9.9.585.1.2.1.1.31
The sum of all negative jitter values for frames sent from destination to source. The number of such values is stored in ipslaEtherJAggMeasuredNumNegDSes.
OBJECT-TYPE    
  Counter32  

ipslaEtherJAggMeasuredSum2NDSLs 1.3.6.1.4.1.9.9.585.1.2.1.1.32
The sum of squares of all negative jitter values for frames sent from destination to source (low order 32 bits).
OBJECT-TYPE    
  Counter32  

ipslaEtherJAggMeasuredSum2NDSHs 1.3.6.1.4.1.9.9.585.1.2.1.1.33
The sum of squares of all negative jitter values for frames sent from destination to source (high order 32 bits).
OBJECT-TYPE    
  Counter32  

ipslaEtherJAggMeasuredFrmLossSDs 1.3.6.1.4.1.9.9.585.1.2.1.1.34
The number of lost frames when sent from source to destination.
OBJECT-TYPE    
  Counter32  

ipslaEtherJAggMeasuredFrmLssDSes 1.3.6.1.4.1.9.9.585.1.2.1.1.35
The number of lost frames when sent from destination to source.
OBJECT-TYPE    
  Counter32  

ipslaEtherJAggMeasuredFrmOutSeqs 1.3.6.1.4.1.9.9.585.1.2.1.1.36
The number of frames arrived out of sequence.
OBJECT-TYPE    
  Counter32  

ipslaEtherJAggMeasuredFrmMIAes 1.3.6.1.4.1.9.9.585.1.2.1.1.37
The number of frames that are lost for which we cannot determine the direction.
OBJECT-TYPE    
  Counter32  

ipslaEtherJAggMeasuredFrmSkippds 1.3.6.1.4.1.9.9.585.1.2.1.1.38
The number of frames that are skipped per operation because the router could not send the packet out.
OBJECT-TYPE    
  Counter32  

ipslaEtherJAggMeasuredErrors 1.3.6.1.4.1.9.9.585.1.2.1.1.39
The number of occasions when an Ethernet jitter operation could not be initiated because of an internal error.
OBJECT-TYPE    
  Counter32  

ipslaEtherJAggMeasuredBusies 1.3.6.1.4.1.9.9.585.1.2.1.1.40
The number of occasions when an Ethernet jitter operation could not be initiated because a previous Ethernet jitter operation has not been completed.
OBJECT-TYPE    
  Counter32  

ipslaEtherJAggMeasuredOWSumSDs 1.3.6.1.4.1.9.9.585.1.2.1.1.41
The sum of one way trip time from source to destination.
OBJECT-TYPE    
  Counter32  

ipslaEtherJAggMeasuredOWSum2SDLs 1.3.6.1.4.1.9.9.585.1.2.1.1.42
The sum of squares of one way trip time from source to destination (low order 32 bits).
OBJECT-TYPE    
  Counter32  

ipslaEtherJAggMeasuredOWSum2SDHs 1.3.6.1.4.1.9.9.585.1.2.1.1.43
The sum of squares of one way trip time from source to destination (high order 32 bits).
OBJECT-TYPE    
  Counter32  

ipslaEtherJAggMeasuredOWMinSD 1.3.6.1.4.1.9.9.585.1.2.1.1.44
The minimum of all one way trip time from source to destination.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMeasuredOWMaxSD 1.3.6.1.4.1.9.9.585.1.2.1.1.45
The maximum of all one way trip time from source to destination.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMeasuredOWSumDSes 1.3.6.1.4.1.9.9.585.1.2.1.1.46
The sum of one way trip time from destination to source.
OBJECT-TYPE    
  Counter32  

ipslaEtherJAggMeasuredOWSum2DSLs 1.3.6.1.4.1.9.9.585.1.2.1.1.47
The sum of squares of one way trip time from destination to source (low order 32 bits).
OBJECT-TYPE    
  Counter32  

ipslaEtherJAggMeasuredOWSum2DSHs 1.3.6.1.4.1.9.9.585.1.2.1.1.48
The sum of squares of one way trip time from destination to source (high order 32 bits).
OBJECT-TYPE    
  Counter32  

ipslaEtherJAggMeasuredOWMinDS 1.3.6.1.4.1.9.9.585.1.2.1.1.49
The minimum of all one way trip time from destination to source.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMeasuredOWMaxDS 1.3.6.1.4.1.9.9.585.1.2.1.1.50
The maximum of all one way trip time from destination to source.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMeasuredNumOWs 1.3.6.1.4.1.9.9.585.1.2.1.1.51
The number of one way trip time that are successfully measured.
OBJECT-TYPE    
  Counter32  

ipslaEtherJAggMeasuredAvgJ 1.3.6.1.4.1.9.9.585.1.2.1.1.52
The average of positive and negative jitter values for source-to-destination and destination-to-source direction.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMeasuredAvgJSD 1.3.6.1.4.1.9.9.585.1.2.1.1.53
The average of positive and negative jitter values in source-to-destination direction.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMeasuredAvgJDS 1.3.6.1.4.1.9.9.585.1.2.1.1.54
The average of positive and negative jitter values in destination-to-source direction.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMinSucFrmLoss 1.3.6.1.4.1.9.9.585.1.2.1.1.55
The minimum number of frames that are dropped successively.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMaxSucFrmLoss 1.3.6.1.4.1.9.9.585.1.2.1.1.56
The maximum number of frames that are dropped successively.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMeasuredIAJOut 1.3.6.1.4.1.9.9.585.1.2.1.1.57
Inter-arrival jitter (RFC 1889) at responder
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMeasuredIAJIn 1.3.6.1.4.1.9.9.585.1.2.1.1.58
Inter-arrival jitter (RFC 1889) at sender
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMeasuredFrmLateAs 1.3.6.1.4.1.9.9.585.1.2.1.1.59
The number of frames that arrived after the timeout.
OBJECT-TYPE    
  Counter32  

ipslaEtherJAggMeasuredFrmUnPrcds 1.3.6.1.4.1.9.9.585.1.2.1.1.60
The number of frames that arrived but could not be processed due to the internal error.
OBJECT-TYPE    
  Counter32  

ipslaEtherJAggMeasuredMaxPosTW 1.3.6.1.4.1.9.9.585.1.2.1.1.61
The two-way maximum of all positive jitter values for frames.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMeasuredMaxNegTW 1.3.6.1.4.1.9.9.585.1.2.1.1.62
The two-way maximum of all negative jitter values for frames.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMeasuredMinPosTW 1.3.6.1.4.1.9.9.585.1.2.1.1.63
The two-way minimum of all positive jitter values for frames.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMeasuredMinNegTW 1.3.6.1.4.1.9.9.585.1.2.1.1.64
The two-way minimum of all negative jitter values for frames.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMeasuredTxFrmsSD 1.3.6.1.4.1.9.9.585.1.2.1.1.65
The number of data frames sent from source to destination.
OBJECT-TYPE    
  Counter64  

ipslaEtherJAggMeasuredTxFrmsDS 1.3.6.1.4.1.9.9.585.1.2.1.1.66
The number of data frames sent from destination to source.
OBJECT-TYPE    
  Counter64  

ipslaEtherJAggMeasuredRxFrmsSD 1.3.6.1.4.1.9.9.585.1.2.1.1.67
The number of data frames received from source to destination.
OBJECT-TYPE    
  Counter64  

ipslaEtherJAggMeasuredRxFrmsDS 1.3.6.1.4.1.9.9.585.1.2.1.1.68
The number of data frames received from destination to source.
OBJECT-TYPE    
  Counter64  

ipslaEtherJAggMeasuredMinLossNumeratorSD 1.3.6.1.4.1.9.9.585.1.2.1.1.69
The numerator for the minimum loss ratio recorded in the source to destination direction.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMeasuredMinLossDenominatorSD 1.3.6.1.4.1.9.9.585.1.2.1.1.70
The denominator for the minimum loss ratio recorded in the source to destination direction.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMeasuredMaxLossNumeratorSD 1.3.6.1.4.1.9.9.585.1.2.1.1.71
The numerator for the maximum loss ratio recorded in the source to destination direction.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMeasuredMaxLossDenominatorSD 1.3.6.1.4.1.9.9.585.1.2.1.1.72
The denominator for the maximum loss ratio recorded in the source to destination direction.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMeasuredAvgLossNumeratorSD 1.3.6.1.4.1.9.9.585.1.2.1.1.73
The numerator for the average loss ratio recorded in the source to destination direction.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMeasuredAvgLossDenominatorSD 1.3.6.1.4.1.9.9.585.1.2.1.1.74
The denominator for the average loss ratio recorded in the source to destination direction.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMeasuredMinLossNumeratorDS 1.3.6.1.4.1.9.9.585.1.2.1.1.75
The numerator for the minimum loss ratio recorded in the destination to source direction.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMeasuredMinLossDenominatorDS 1.3.6.1.4.1.9.9.585.1.2.1.1.76
The denominator for the minimum loss ratio recorded in the destination to source direction.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMeasuredMaxLossNumeratorDS 1.3.6.1.4.1.9.9.585.1.2.1.1.77
The numerator for the maximum loss ratio recorded in the destination to source direction.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMeasuredMaxLossDenominatorDS 1.3.6.1.4.1.9.9.585.1.2.1.1.78
The denominator for the maximum loss ratio recorded in the destination to source direction.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMeasuredAvgLossNumeratorDS 1.3.6.1.4.1.9.9.585.1.2.1.1.79
The numerator for the average loss ratio recorded in the destination to source direction.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMeasuredAvgLossDenominatorDS 1.3.6.1.4.1.9.9.585.1.2.1.1.80
The denominator for the average loss ratio recorded in the destination to source direction.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMeasuredCumulativeLossNumeratorSD 1.3.6.1.4.1.9.9.585.1.2.1.1.81
The numerator for the loss ratio recorded in the source to destination direction. This value is cumulative over the period of this interval.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMeasuredCumulativeLossDenominatorSD 1.3.6.1.4.1.9.9.585.1.2.1.1.82
The denominator for the loss ratio recorded in the source to destination direction. This value is cumulative over the period of this interval.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMeasuredCumulativeAvgLossNumeratorSD 1.3.6.1.4.1.9.9.585.1.2.1.1.83
The numerator for the average loss ratio recorded in the source to destination direction. This value is cumulative over the perios of this interval.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMeasuredCumulativeAvgLossDenominatorSD 1.3.6.1.4.1.9.9.585.1.2.1.1.84
The denominator for the average loss ratio recorded in the source to destination direction. This value is cumulative over the period of this interval.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMeasuredCumulativeLossNumeratorDS 1.3.6.1.4.1.9.9.585.1.2.1.1.85
The numerator for the loss ratio recorded in the destination to source direction. This value is cumulative over the period of this interval.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMeasuredCumulativeLossDenominatorDS 1.3.6.1.4.1.9.9.585.1.2.1.1.86
The denominator for the loss ratio recorded in the destination to source direction. This valued is cumulative over the period of this interval.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMeasuredCumulativeAvgLossNumeratorDS 1.3.6.1.4.1.9.9.585.1.2.1.1.87
The numerator for the average loss ratio recorded in the destination to source direction. This value is cumulative over the period of this interval.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJAggMeasuredCumulativeAvgLossDenominatorDS 1.3.6.1.4.1.9.9.585.1.2.1.1.88
The denominator for the average loss ratio recorded in the destination to source direction. This value is cumulative over the period of this interval.
OBJECT-TYPE    
  Gauge32  

ipslaEthernetLatestOper 1.3.6.1.4.1.9.9.585.1.3
OBJECT IDENTIFIER    

ipslaEtherJitterLatestStatsTable 1.3.6.1.4.1.9.9.585.1.3.1
The 'ethernetJitter' operation sends out frames at the frequency specified by rttMonCtrlAdminFrequency. This table contains the statistics calculated for the latest sent frames. Each conceptual row in this table corresponds to an 'ethernetJitter' operation defined in rttMonCtrlAdminTable and has same index as rttMonCtrlAdminTable.
OBJECT-TYPE    
  SEQUENCE OF  
    IpslaEtherJitterLatestStatsEntry

ipslaEtherJitterLatestStatsEntry 1.3.6.1.4.1.9.9.585.1.3.1.1
A collection of objects that record the latest Ethernet jitter operation. An entry is created only when the following objects are valid. - rttMonCtrlAdminRttType - rttMonEchoAdminProtocol The entry will start to collect data when rttMonCtrlAdminStatus is in 'active' state. The entry will be removed when the rttMonCtrlAdminStatus is changed to 'destroy' state.
OBJECT-TYPE    
  IpslaEtherJitterLatestStatsEntry  

ipslaEtherJitterLatestNumRTT 1.3.6.1.4.1.9.9.585.1.3.1.1.1
The number of RTT's that were successfully measured.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestRTTSum 1.3.6.1.4.1.9.9.585.1.3.1.1.2
The sum of RTT's that are successfully measured. The number of successfully measured RTT is stored in ipslaEtherJitterLatestNumRTT.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestRTTSum2 1.3.6.1.4.1.9.9.585.1.3.1.1.3
The sum of squares of RTT's that are successfully measured.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestRTTMin 1.3.6.1.4.1.9.9.585.1.3.1.1.4
The minimum of RTT's that were successfully measured.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestRTTMax 1.3.6.1.4.1.9.9.585.1.3.1.1.5
The maximum of RTT's that were successfully measured.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestMinPosSD 1.3.6.1.4.1.9.9.585.1.3.1.1.6
The minimum of all positive jitter values for frames sent from source to destination.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestMaxPosSD 1.3.6.1.4.1.9.9.585.1.3.1.1.7
The maximum of all positive jitter values for frames sent from source to destination.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestNumPosSD 1.3.6.1.4.1.9.9.585.1.3.1.1.8
The number of all positive jitter values for frames sent from source to destination.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestSumPosSD 1.3.6.1.4.1.9.9.585.1.3.1.1.9
The sum of all positive jitter values for frames sent source to destination. The number of such values is stored in ipslaEtherJitterLatestNumPosSD.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestSum2PosSD 1.3.6.1.4.1.9.9.585.1.3.1.1.10
The sum of square of all positive jitter values for frames sent from source to destination.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestMinNegSD 1.3.6.1.4.1.9.9.585.1.3.1.1.11
The minimum of absolute values of all negative jitter values for frames sent from source to destination.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestMaxNegSD 1.3.6.1.4.1.9.9.585.1.3.1.1.12
The maximum of absolute values of all negative jitter values for frames sent from source to destination.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestNumNegSD 1.3.6.1.4.1.9.9.585.1.3.1.1.13
The number of all negative jitter values for frames sent from source to destination.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestSumNegSD 1.3.6.1.4.1.9.9.585.1.3.1.1.14
The sum of all negative jitter values for frames sent from source to destination. The number of such values is stored in ipslaEtherJitterLatestNumNegSD.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestSum2NegSD 1.3.6.1.4.1.9.9.585.1.3.1.1.15
The sum of square of all negative jitter values for frames sent from source to destination.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestMinPosDS 1.3.6.1.4.1.9.9.585.1.3.1.1.16
The minimum of all positive jitter values for frames sent from destination to source.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestMaxPosDS 1.3.6.1.4.1.9.9.585.1.3.1.1.17
The maximum of all positive jitter values for frames sent from destination to source.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestNumPosDS 1.3.6.1.4.1.9.9.585.1.3.1.1.18
The number of all positive jitter values for frames sent from destination to source.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestSumPosDS 1.3.6.1.4.1.9.9.585.1.3.1.1.19
The sum of all positive jitter values for frames sent from destination to source. The number of such values is stored in ipslaEtherJitterLatestNumPosDS.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestSum2PosDS 1.3.6.1.4.1.9.9.585.1.3.1.1.20
The sum of squares of all positive jitter values for frames sent from destination to source.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestMinNegDS 1.3.6.1.4.1.9.9.585.1.3.1.1.21
The minimum of all negative jitter values for frames sent from destination to source.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestMaxNegDS 1.3.6.1.4.1.9.9.585.1.3.1.1.22
The maximum of all negative jitter values for frames sent from destination to source.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestNumNegDS 1.3.6.1.4.1.9.9.585.1.3.1.1.23
The number of all negative jitter values for frames sent from destination to source.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestSumNegDS 1.3.6.1.4.1.9.9.585.1.3.1.1.24
The sum of all negative jitter values for frames sent from destination to source. The number of such values is stored in ipslaEtherJitterLatestNumNegDS.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestSum2NegDS 1.3.6.1.4.1.9.9.585.1.3.1.1.25
The sum of squares of all negative jitter values for frames sent from destination to source.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestFrmLossSD 1.3.6.1.4.1.9.9.585.1.3.1.1.26
The number of frames lost when sent from source to destination.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestFrmLossDS 1.3.6.1.4.1.9.9.585.1.3.1.1.27
The number of frames lost when sent from destination to source.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestFrmOutSeq 1.3.6.1.4.1.9.9.585.1.3.1.1.28
The number of frames arrived out of sequence.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestFrmMIA 1.3.6.1.4.1.9.9.585.1.3.1.1.29
The number of frames that are lost for which we cannot determine the direction.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestFrmSkipped 1.3.6.1.4.1.9.9.585.1.3.1.1.30
The number of frames in the operation that could not be initiated due to an internal error.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestSense 1.3.6.1.4.1.9.9.585.1.3.1.1.31
An application specific sense code for the completion status.
OBJECT-TYPE    
  RttResponseSense  

ipslaEtherJitterLatestFrmLateA 1.3.6.1.4.1.9.9.585.1.3.1.1.32
The number of frames that arrived after the timeout.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestMinSucFrmL 1.3.6.1.4.1.9.9.585.1.3.1.1.33
The minimum number of frames that are dropped successively.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestMaxSucFrmL 1.3.6.1.4.1.9.9.585.1.3.1.1.34
The maximum number of frames that are dropped successively.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestOWSumSD 1.3.6.1.4.1.9.9.585.1.3.1.1.35
The sum of one way trip time from source to destination.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestOWSum2SD 1.3.6.1.4.1.9.9.585.1.3.1.1.36
The sum of squares of one way trip time from source to destination.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestOWMinSD 1.3.6.1.4.1.9.9.585.1.3.1.1.37
The minimum of all one way trip time from source to destination.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestOWMaxSD 1.3.6.1.4.1.9.9.585.1.3.1.1.38
The maximum of all one way trip time from source to destination.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestOWSumDS 1.3.6.1.4.1.9.9.585.1.3.1.1.39
The sum of one way trip time from destination to source.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestOWSum2DS 1.3.6.1.4.1.9.9.585.1.3.1.1.40
The sum of squares of one way trip time from destination to source.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestOWMinDS 1.3.6.1.4.1.9.9.585.1.3.1.1.41
The minimum of all one way trip time from destination to source.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestOWMaxDS 1.3.6.1.4.1.9.9.585.1.3.1.1.42
The maximum of all one way trip time from destination to source.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestNumOW 1.3.6.1.4.1.9.9.585.1.3.1.1.43
The number of successful one way trip time measurements.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestAvgJitter 1.3.6.1.4.1.9.9.585.1.3.1.1.44
The average of positive and negative jitter values in Source-to-Destination and Destination-to-Source direction.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestAvgSDJ 1.3.6.1.4.1.9.9.585.1.3.1.1.45
The average of positive and negative jitter values from source to destination.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestAvgDSJ 1.3.6.1.4.1.9.9.585.1.3.1.1.46
The average of positive and negative jitter values from destination to source.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestOWAvgSD 1.3.6.1.4.1.9.9.585.1.3.1.1.47
The average one way trip time from source to destination.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestOWAvgDS 1.3.6.1.4.1.9.9.585.1.3.1.1.48
The average one way trip time from destination to source.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestIAJOut 1.3.6.1.4.1.9.9.585.1.3.1.1.49
Inter-arrival jitter (RFC 1889) at responder.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJitterLatestIAJIn 1.3.6.1.4.1.9.9.585.1.3.1.1.50
Inter-arrival jitter (RFC 1889) at source.
OBJECT-TYPE    
  Gauge32  

ipslaEtherJLatestFrmUnProcessed 1.3.6.1.4.1.9.9.585.1.3.1.1.51
The number of frames in the operation that could not be processed due to high CPU load.
OBJECT-TYPE    
  Gauge32  

ciscoIpSlaEthernetMIBConform 1.3.6.1.4.1.9.9.585.2
OBJECT IDENTIFIER    

ciscoIpSlaEthernetCompliances 1.3.6.1.4.1.9.9.585.2.1
OBJECT IDENTIFIER    

ciscoIpSlaEthernetCompliance 1.3.6.1.4.1.9.9.585.2.1.1
The compliance statement for (1) Ethernet Jitter operation and statistics
MODULE-COMPLIANCE    

ciscoIpSlaEthernetComplianceRev2 1.3.6.1.4.1.9.9.585.2.1.2
The compliance statement for (1) Ethernet Jitter operation and statistics (2) supporting IP SLA Auto-Ethernet-CFM
MODULE-COMPLIANCE    

ciscoIpSlaEthernetComplianceRev3 1.3.6.1.4.1.9.9.585.2.1.3
The compliance statement for (1) Ethernet Jitter operation and statistics (2) supporting IP SLA Y1731
MODULE-COMPLIANCE    

ciscoIpSlaEthernetMIBGroups 1.3.6.1.4.1.9.9.585.2.2
OBJECT IDENTIFIER    

ciscoIpSlaEthernetAutoGroup 1.3.6.1.4.1.9.9.585.2.2.1
A collection of objects that were added to support Auto-Ethernet-CFM.
OBJECT-GROUP    

ciscoIpSlaEthernetStatsGroup 1.3.6.1.4.1.9.9.585.2.2.2
A collection of statistics objects related to Ethernet Jitter Probe.
OBJECT-GROUP    

ciscoIpSlaEthernetAutoEVCGroup 1.3.6.1.4.1.9.9.585.2.2.3
A collection of objects which provides the support for Auto-Ethernet-CFM ping/jitter operation with Ethernet Virtual Connection.
OBJECT-GROUP    

ciscoIpSlaEthernetY1731Group 1.3.6.1.4.1.9.9.585.2.2.4
A collection of objects which provides the support for Y1731 operation with Ethernet Virtual Connection.
OBJECT-GROUP    

Defined Objects

IpslaEthernetGrpCtrlEntry  
SEQUENCE    
  RttMonCtrlIndex as ipslaEthernetGrpCtrlIndex  
  RowStatus as ipslaEthernetGrpCtrlStatus  
  StorageType as ipslaEthernetGrpCtrlStorageType  
  RttMonRttType as ipslaEthernetGrpCtrlRttType  
  SnmpAdminString as ipslaEthernetGrpCtrlOwner  
  SnmpAdminString as ipslaEthernetGrpCtrlTag  
  Unsigned32 as ipslaEthernetGrpCtrlThreshold  
  Unsigned32 as ipslaEthernetGrpCtrlTimeout  
  RttMonIdLst as ipslaEthernetGrpCtrlProbeList  
  VlanId as ipslaEthernetGrpCtrlVLAN  
  Dot1agCfmMaintDomainNameType as ipslaEthernetGrpCtrlDomainNameType  
  Dot1agCfmMaintDomainName as ipslaEthernetGrpCtrlDomainName  
  Unsigned32 as ipslaEthernetGrpCtrlReqDataSize  
  RttMonIdLst as ipslaEthernetGrpCtrlMPIDExLst  
  Layer2Cos as ipslaEthernetGrpCtrlCOS  
  Unsigned32 as ipslaEthernetGrpCtrlInterval  
  Unsigned32 as ipslaEthernetGrpCtrlNumFrames  
  TimeTicks as ipslaEthernetGrpScheduleRttStartTime  
  Unsigned32 as ipslaEthernetGrpSchedulePeriod  
  Unsigned32 as ipslaEthernetGrpScheduleFrequency  
  SnmpAdminString as ipslaEthernetGrpCtrlEVC  
  INTEGER as ipslaEthernetGrpCtrlServiceInsType  

IpslaEthernetGrpReactEntry  
SEQUENCE    
  RttMonCtrlIndex as ipslaEthernetGrpReactConfigIndex  
  RowStatus as ipslaEthernetGrpReactStatus  
  StorageType as ipslaEthernetGrpReactStorageType  
  RttMonReactVar as ipslaEthernetGrpReactVar  
  INTEGER as ipslaEthernetGrpReactThresholdType  
  Unsigned32 as ipslaEthernetGrpReactThresholdRising  
  Unsigned32 as ipslaEthernetGrpReactThresholdFalling  
  Unsigned32 as ipslaEthernetGrpReactThresholdCountX  
  Unsigned32 as ipslaEthernetGrpReactThresholdCountY  
  INTEGER as ipslaEthernetGrpReactActionType  

IpslaEtherJitterLatestStatsEntry  
SEQUENCE    
  Gauge32 as ipslaEtherJitterLatestNumRTT  
  Gauge32 as ipslaEtherJitterLatestRTTSum  
  Gauge32 as ipslaEtherJitterLatestRTTSum2  
  Gauge32 as ipslaEtherJitterLatestRTTMin  
  Gauge32 as ipslaEtherJitterLatestRTTMax  
  Gauge32 as ipslaEtherJitterLatestMinPosSD  
  Gauge32 as ipslaEtherJitterLatestMaxPosSD  
  Gauge32 as ipslaEtherJitterLatestNumPosSD  
  Gauge32 as ipslaEtherJitterLatestSumPosSD  
  Gauge32 as ipslaEtherJitterLatestSum2PosSD  
  Gauge32 as ipslaEtherJitterLatestMinNegSD  
  Gauge32 as ipslaEtherJitterLatestMaxNegSD  
  Gauge32 as ipslaEtherJitterLatestNumNegSD  
  Gauge32 as ipslaEtherJitterLatestSumNegSD  
  Gauge32 as ipslaEtherJitterLatestSum2NegSD  
  Gauge32 as ipslaEtherJitterLatestMinPosDS  
  Gauge32 as ipslaEtherJitterLatestMaxPosDS  
  Gauge32 as ipslaEtherJitterLatestNumPosDS  
  Gauge32 as ipslaEtherJitterLatestSumPosDS  
  Gauge32 as ipslaEtherJitterLatestSum2PosDS  
  Gauge32 as ipslaEtherJitterLatestMinNegDS  
  Gauge32 as ipslaEtherJitterLatestMaxNegDS  
  Gauge32 as ipslaEtherJitterLatestNumNegDS  
  Gauge32 as ipslaEtherJitterLatestSumNegDS  
  Gauge32 as ipslaEtherJitterLatestSum2NegDS  
  Gauge32 as ipslaEtherJitterLatestFrmLossSD  
  Gauge32 as ipslaEtherJitterLatestFrmLossDS  
  Gauge32 as ipslaEtherJitterLatestFrmOutSeq  
  Gauge32 as ipslaEtherJitterLatestFrmMIA  
  Gauge32 as ipslaEtherJitterLatestFrmSkipped  
  RttResponseSense as ipslaEtherJitterLatestSense  
  Gauge32 as ipslaEtherJitterLatestFrmLateA  
  Gauge32 as ipslaEtherJitterLatestMinSucFrmL  
  Gauge32 as ipslaEtherJitterLatestMaxSucFrmL  
  Gauge32 as ipslaEtherJitterLatestOWSumSD  
  Gauge32 as ipslaEtherJitterLatestOWSum2SD  
  Gauge32 as ipslaEtherJitterLatestOWMinSD  
  Gauge32 as ipslaEtherJitterLatestOWMaxSD  
  Gauge32 as ipslaEtherJitterLatestOWSumDS  
  Gauge32 as ipslaEtherJitterLatestOWSum2DS  
  Gauge32 as ipslaEtherJitterLatestOWMinDS  
  Gauge32 as ipslaEtherJitterLatestOWMaxDS  
  Gauge32 as ipslaEtherJitterLatestNumOW  
  Gauge32 as ipslaEtherJitterLatestAvgJitter  
  Gauge32 as ipslaEtherJitterLatestAvgSDJ  
  Gauge32 as ipslaEtherJitterLatestAvgDSJ  
  Gauge32 as ipslaEtherJitterLatestOWAvgSD  
  Gauge32 as ipslaEtherJitterLatestOWAvgDS  
  Gauge32 as ipslaEtherJitterLatestIAJOut  
  Gauge32 as ipslaEtherJitterLatestIAJIn  
  Gauge32 as ipslaEtherJLatestFrmUnProcessed  

IpslaEtherJitterAggStatsEntry  
SEQUENCE    
  TimeStamp as ipslaEtherJAggStatsStartTimeId  
  Counter32 as ipslaEtherJAggMeasuredCmpletions  
  Counter32 as ipslaEtherJAggMeasuredOvThrshlds  
  Counter32 as ipslaEtherJAggMeasuredNumRTTs  
  Counter32 as ipslaEtherJAggMeasuredRTTSums  
  Counter32 as ipslaEtherJAggMeasuredRTTSum2Ls  
  Counter32 as ipslaEtherJAggMeasuredRTTSum2Hs  
  Gauge32 as ipslaEtherJAggMeasuredRTTMin  
  Gauge32 as ipslaEtherJAggMeasuredRTTMax  
  Gauge32 as ipslaEtherJAggMeasuredMinPosSD  
  Gauge32 as ipslaEtherJAggMeasuredMaxPosSD  
  Counter32 as ipslaEtherJAggMeasuredNumPosSDs  
  Counter32 as ipslaEtherJAggMeasuredSumPosSDs  
  Counter32 as ipslaEtherJAggMeasuredSum2PSDLs  
  Counter32 as ipslaEtherJAggMeasuredSum2PSDHs  
  Gauge32 as ipslaEtherJAggMeasuredMinNegSD  
  Gauge32 as ipslaEtherJAggMeasuredMaxNegSD  
  Counter32 as ipslaEtherJAggMeasuredNumNegSDs  
  Counter32 as ipslaEtherJAggMeasuredSumNegSDs  
  Counter32 as ipslaEtherJAggMeasuredSum2NSDLs  
  Counter32 as ipslaEtherJAggMeasuredSum2NSDHs  
  Gauge32 as ipslaEtherJAggMeasuredMinPosDS  
  Gauge32 as ipslaEtherJAggMeasuredMaxPosDS  
  Counter32 as ipslaEtherJAggMeasuredNumPosDSes  
  Counter32 as ipslaEtherJAggMeasuredSumPosDSes  
  Counter32 as ipslaEtherJAggMeasuredSum2PDSLs  
  Counter32 as ipslaEtherJAggMeasuredSum2PDSHs  
  Gauge32 as ipslaEtherJAggMeasuredMinNegDS  
  Gauge32 as ipslaEtherJAggMeasuredMaxNegDS  
  Counter32 as ipslaEtherJAggMeasuredNumNegDSes  
  Counter32 as ipslaEtherJAggMeasuredSumNegDSes  
  Counter32 as ipslaEtherJAggMeasuredSum2NDSLs  
  Counter32 as ipslaEtherJAggMeasuredSum2NDSHs  
  Counter32 as ipslaEtherJAggMeasuredFrmLossSDs  
  Counter32 as ipslaEtherJAggMeasuredFrmLssDSes  
  Counter32 as ipslaEtherJAggMeasuredFrmOutSeqs  
  Counter32 as ipslaEtherJAggMeasuredFrmMIAes  
  Counter32 as ipslaEtherJAggMeasuredFrmSkippds  
  Counter32 as ipslaEtherJAggMeasuredErrors  
  Counter32 as ipslaEtherJAggMeasuredBusies  
  Counter32 as ipslaEtherJAggMeasuredOWSumSDs  
  Counter32 as ipslaEtherJAggMeasuredOWSum2SDLs  
  Counter32 as ipslaEtherJAggMeasuredOWSum2SDHs  
  Gauge32 as ipslaEtherJAggMeasuredOWMinSD  
  Gauge32 as ipslaEtherJAggMeasuredOWMaxSD  
  Counter32 as ipslaEtherJAggMeasuredOWSumDSes  
  Counter32 as ipslaEtherJAggMeasuredOWSum2DSLs  
  Counter32 as ipslaEtherJAggMeasuredOWSum2DSHs  
  Gauge32 as ipslaEtherJAggMeasuredOWMinDS  
  Gauge32 as ipslaEtherJAggMeasuredOWMaxDS  
  Counter32 as ipslaEtherJAggMeasuredNumOWs  
  Gauge32 as ipslaEtherJAggMeasuredAvgJ  
  Gauge32 as ipslaEtherJAggMeasuredAvgJSD  
  Gauge32 as ipslaEtherJAggMeasuredAvgJDS  
  Gauge32 as ipslaEtherJAggMinSucFrmLoss  
  Gauge32 as ipslaEtherJAggMaxSucFrmLoss  
  Gauge32 as ipslaEtherJAggMeasuredIAJOut  
  Gauge32 as ipslaEtherJAggMeasuredIAJIn  
  Counter32 as ipslaEtherJAggMeasuredFrmLateAs  
  Counter32 as ipslaEtherJAggMeasuredFrmUnPrcds  
  Gauge32 as ipslaEtherJAggMeasuredMaxPosTW  
  Gauge32 as ipslaEtherJAggMeasuredMaxNegTW  
  Gauge32 as ipslaEtherJAggMeasuredMinPosTW  
  Gauge32 as ipslaEtherJAggMeasuredMinNegTW  
  Counter64 as ipslaEtherJAggMeasuredTxFrmsSD  
  Counter64 as ipslaEtherJAggMeasuredTxFrmsDS  
  Counter64 as ipslaEtherJAggMeasuredRxFrmsSD  
  Counter64 as ipslaEtherJAggMeasuredRxFrmsDS  
  Gauge32 as ipslaEtherJAggMeasuredMinLossNumeratorSD  
  Gauge32 as ipslaEtherJAggMeasuredMinLossDenominatorSD  
  Gauge32 as ipslaEtherJAggMeasuredMaxLossNumeratorSD  
  Gauge32 as ipslaEtherJAggMeasuredMaxLossDenominatorSD  
  Gauge32 as ipslaEtherJAggMeasuredAvgLossNumeratorSD  
  Gauge32 as ipslaEtherJAggMeasuredAvgLossDenominatorSD  
  Gauge32 as ipslaEtherJAggMeasuredMinLossNumeratorDS  
  Gauge32 as ipslaEtherJAggMeasuredMinLossDenominatorDS  
  Gauge32 as ipslaEtherJAggMeasuredMaxLossNumeratorDS  
  Gauge32 as ipslaEtherJAggMeasuredMaxLossDenominatorDS  
  Gauge32 as ipslaEtherJAggMeasuredAvgLossNumeratorDS  
  Gauge32 as ipslaEtherJAggMeasuredAvgLossDenominatorDS  
  Gauge32 as ipslaEtherJAggMeasuredCumulativeLossNumeratorSD  
  Gauge32 as ipslaEtherJAggMeasuredCumulativeLossDenominatorSD  
  Gauge32 as ipslaEtherJAggMeasuredCumulativeAvgLossNumeratorSD  
  Gauge32 as ipslaEtherJAggMeasuredCumulativeAvgLossDenominatorSD  
  Gauge32 as ipslaEtherJAggMeasuredCumulativeLossNumeratorDS  
  Gauge32 as ipslaEtherJAggMeasuredCumulativeLossDenominatorDS  
  Gauge32 as ipslaEtherJAggMeasuredCumulativeAvgLossNumeratorDS  
  Gauge32 as ipslaEtherJAggMeasuredCumulativeAvgLossDenominatorDS