
| SNMPv2-SMI | SNMPv2-TC | CISCO-SMI |
| Integer32 | MODULE-IDENTITY | Unsigned32 |
| TEXTUAL-CONVENTION | ciscoMgmt |
| ciscoItpTextualConventions | 1.3.6.1.4.1.9.9.231 | ||
| The defines textual conventions used by to manage devices related to the SS7 network. The relevant ITU documents describing this technology is the ITU Q series, including ITU Q.700: Introduction to CCITT Signalling System No. 7 and ITU Q.701 Functional description of the message transfer part (MTP) of Signalling System No. 7. Abbreviations: CDPA - Called Party Point Code CGPA - Calling Party Point Code CLLI - Common Language Location Codes CR - Connection Request message CREF - Connection Refusal message DPC - Destination Point Code ERR - Error message GTA - Global Title Address GTI - Global Title Indicator GTT - Global Title Translation LUDT - long unitdata message LUDTS - long unitdata service message M2PA - MTP2 Peer-to-Peer Adaptation Layer M3UA - MTP3-User Adaptation MAP - Mated Application Table MSU - Message Signal Unit MTP - Message Transport Protocol MTP2 - Layer 2 of Message Transport Protocol MTP3 - Layer 3 of Message Transport Protocol NAI - Nature of Address Indicator NP - Numbering Plan NTT - The Japanese Nippon Telephone & Telegraph OPC - Originating Point Code PC - Point Code RTN - Route Table Name RSR - Reset Request message SCCP - Signalling Connection Control Part SCTP - Stream Transmission Protocol(RFC 2960) SI - Signalling Indicator SP - Signalling Point SLC - Signalling Link Code SLS - Signalling Link Selector SSN - Subsystem Number SUA - SCCP-User Adaptation TFR - Transfer Restricted messages TT - Title Translation TTC - The Japanese Telecommunications Technology Committee UDT - unitdata message UDTS - unitdata service message XUDT - extended unitdata message XUDTS - extended unitdata service message | |||
| MODULE-IDENTITY | |||
| CItpTcAclId | |||
| An numeric Identifier used to specify an access list used to permit and deny packets based on MTP3 information. Either the value 0 or the value of access list identifier. A value of zero indicates that an access list is not specified. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 0 | 2700..2999 | ||
| CItpTcCLLI | |||
| Common Language Location Codes (CLLI Codes). An 11-character standardized geographic identifier that uniquely identifies the geographic location of telecommunication equipment. The CLLI code is supported as octet string containing administrative information in human-readable form. The use of control codes should be avoided. The use of newline should be avoided. The use of leading or trailing white space should be avoided. | |||
| TEXTUAL-CONVENTION | |||
| OCTET STRING | SIZE(0..11) | ||
| CItpTcDisplayPC | |||
| The Point Code in formatted based on the variant and the customer defined parameters. | |||
| TEXTUAL-CONVENTION | |||
| OCTET STRING | SIZE(1..12) | ||
| CItpTcEncodingSchemeValue | |||
| The encoding scheme value. | |||
| TEXTUAL-CONVENTION | |||
| Integer32 | 0..15 | ||
| CItpTcGlobalTitleSelector | |||
| Global Title Selector. 'nai' : Global title translation based on nature of address indicator. 'tt' : Global title translation based on translation type. 'ttNpEs' : Global title translation based on translation type, numbering plan value and Encoding Scheme Value. 'ttNpNaiEs' : Global title translation based on translation type, numbering plan, value, nature of address indicator and encoding scheme value. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | nai(1), tt(2), ttNpEs(3), ttNpNaiEs(4) | ||
| CItpTcGlobalTitleSelectorName | |||
| The configured name associated with SCCP GTT Selector. An octet string specified by an administrator that must be in human-readable form. The names must conform to the allowed characters that can be specified via Command Line Interface(CLI). The names cannot contain control character and should not contain leading or trailing white space. | |||
| TEXTUAL-CONVENTION | |||
| OCTET STRING | SIZE(1..9) | ||
| CItpTcGtaAddr | |||
| The configured digits in the SCCP GTT Global Title Address. An octet string specified by an administrator must be in human-readable form. The names must conform to the allowed characters that can be specified via Command Line Interface(CLI). The names cannot contain control character and should not contain leading or trailing white space. | |||
| TEXTUAL-CONVENTION | |||
| OCTET STRING | SIZE(8) | ||
| CItpTcGtaLongAddr | |||
| The configured hexadecimal digits in the SCCP GTT Global Title Address. | |||
| TEXTUAL-CONVENTION | |||
| OCTET STRING | SIZE(0..64) | ||
| CItpTcGtaDisplay | |||
| The configured digits in the SCCP GTT Global Title Address. It consists of ASCII representation of GTA hex digits. This textual convention has been deprecated and replaced by CItpTcGtaDisplayZB. | |||
| TEXTUAL-CONVENTION | |||
| OCTET STRING | SIZE(1..15) | ||
| CItpTcGtaDisplayZB | |||
| The configured digits in the SCCP GTT Global Title Address. It consists of ASCII representation of GTA hex digits. | |||
| TEXTUAL-CONVENTION | |||
| OCTET STRING | SIZE(0..15) | ||
| CItpTcGtaLongDisplay | |||
| The configured digits in the SCCP GTT Global Title Address. It consists of ASCII representation of GTA hex digits. | |||
| TEXTUAL-CONVENTION | |||
| OCTET STRING | SIZE(0..64) | ||
| CItpTcGtaDisplayLen | |||
| The SCCP GTT Global Title Address length. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 1..15 | ||
| CItpTcGtaLongDisplayLen | |||
| The SCCP GTT Global Title Address length. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 0..64 | ||
| CItpTcNetworkName | |||
| The network name is used to indicate the network in which this signalling point is participating. One or more instances of signalling points can exist in the same physical device. This identifier will be used to correlate instances of signalling points by network. When multiple instance support is not enable the network name will default to the null string. An octet string specified by an administrator that must be in human-readable form. The names must conform to the allowed characters that can be specified via Command Line Interface(CLI). The names cannot contain control character and should not contain leading or trailing white space. | |||
| TEXTUAL-CONVENTION | |||
| OCTET STRING | SIZE(0..19) | ||
| CItpTcInstanceNumber | |||
| The instance number used to select a particular Signalling point. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 0..255 | ||
| CItpTcLinksetId | |||
| The configured name associated with an Signalling Point Linkset. An octet string specified by an administrator that must be in human-readable form. The names must conform to the allowed characters that can be specified via Command Line Interface(CLI). The names cannot contain control character and should not contain leading or trailing white space. | |||
| TEXTUAL-CONVENTION | |||
| OCTET STRING | SIZE(1..19) | ||
| CItpTcLinkSLC | |||
| The Signalling Link Code. This is the link identifier within a linkset. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 0..15 | ||
| CItpTcLinkType | |||
| The link types. 'other' : This link is of some type not listed below. 'serial' : This link is a serial link transporting SS7 traffic. 'sctpIp' : This a SCTP/IP link transporting SS7 traffic. 'hsl' : This link is a high speed link using the ATM protocol for transporting SS7 traffic. 'virtual': This link is virtual link used to connect to instance of signalling point running on the same physical device. The link will be used to send and manage traffic between two signalling acting as a gateway. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | other(1), serial(2), sctpIp(3), hsl(4), virtual(5) | ||
| CItpTcNAI | |||
| The SCCP GTT Network Address Indicator (NAI). The following values are generally used: Unknown Nature of Address (0), Subscriber Number (1), Reserved for national use (2), National Significant Number (3), International Number (4), Maximum NAI (127), Invalid NAI (253), Wild NAI (254). | |||
| TEXTUAL-CONVENTION | |||
| Integer32 | 0..255 | ||
| CItpTcNetworkIndicator | |||
| Network Indicator: international - International network national - National network reserved - Reserved for national use spare - Spare (for international use only) 'international' : International network 'internationalSpare' : International network spare 'national' : National network 'nationalSpare' : National network Spare | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | international(0), internationatSpare(1), national(2), nationalSpare(3) | ||
| CItpTcNumberingPlan | |||
| The SCCP GTT Numbering Plan (NP). The following values are generally used: Unknown NP (0), ISDN/Telephony NP (1), Spare (2), Data NP (3), Telex NP (4), Maritime Mobile NP (5), Land Mobile NP (6), ISDN/Mobile NP (7), Private NP (8). Max NP (15), Invalid NP (253), Wild NP (254). | |||
| TEXTUAL-CONVENTION | |||
| Integer32 | 0..255 | ||
| CItpTcPointCode | |||
| The SS7 network node address as specified in the following references. The format of the Point code depends on the variant defined in the CgspSS7Variant object as follows. 33222222222211111111110000000000 10987654321098765432109876543210 ANSI: nnnnnnnn - Network cccccccc - Cluster mmmmmmmm - Member ITU: zzz - Zone aaaaaaaa - Area/Network iii - Identifier NTT: zzzzz - Zone aaaa - Area/Network iiiiiii - Identifier TTC: zzzzz - Zone aaaa - Area/Network iiiiiii - Identifier Note: The China variant has the same format as ANSI. This form of the point-code is not intended for for presentation. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 0..16777216 | ||
| CItpTcPointCodeMask | |||
| A mask used to perform different operations on pointcodes. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 0..16777216 | ||
| CItpTcPointCodeType | |||
| List of the possible Point Code types. 'primary' : The primary point used to communicate information on the Signalling point. 'additional' : Additional point codes. 'capability' : capability point codes. 'xua' : MTP3-User Adaptation point codes or SCCP-User Adaptation point codes. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | primary(1), additional(2), capability(3), xua(4) | ||
| CItpTcQos | |||
| The quality of service classification to be assigned to the IP packets used to transport the SS7 messages. The value can be from one to seven when selecting a Qos class or 255 to indicate the packet will not be assigned a Qos class. This value will be set to zero when cItpSpLinkType indicates that Quality of Service does not apply to this link. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 0..7 | 255 | ||
| CItpTcRouteTableName | |||
| The configured name associated with an SP Route Table. An octet string specified by an administrator that must be in human-readable form. The names must conform to the allowed characters that can be specified via Command Line Interface(CLI). The names cannot contain control character and should not contain leading or trailing white space. | |||
| TEXTUAL-CONVENTION | |||
| OCTET STRING | SIZE(1..19) | ||
| CItpTcServiceIndicator | |||
| The list of possible Service Indicator values. This identifies the type of SS7 packet. The service indicator codes for the international Signalling network are allocated as follows: 'SNMM' : Signalling network management messages (SNMM) 'SNTM' : Signalling network testing and maintenance messages (SNTM) 'Spare2' : Spare 2 'SCCP' : SCCP 'TUP' : Telephone User Part (TUP) 'ISUP' : ISDN User Part (ISUP) 'DUPC' : Data User Part, call and circuit-related messages (DUPC) 'DUPF' : Data User Part, facility registration and cancellation messages (DUPF) 'MTUP' : Reserved for MTP Testing User Part (MTUP) 'BISUP' : Broadband ISDN User Part (BISUP) 'SISUP' : Satellite ISDN User Part (SISUP) 'Spare11' : Spare 11 'Spare12' : Spare 12 'Spare13' : Spare 13 'Spare14' : Spare 14 'Spare15' : Spare 15 | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | snmm(0), sntm(1), spare2(2), sccp(3), tup(4), isup(5), dupc(6), dupf(7), mtup(8), bisup(9), sisup(10), spare11(11), spare12(12), spare13(13), spare14(14), spare15(15) | ||
| CItpTcSls | |||
| The Signalling Link Selector is a numeric value that contains the MTP3 packets to allow load balancing of traffic across a link within a linkset or combined linkset. Each linkset provides one or more tables used to map Signalling Link Selectors to Signalling Link Codes. The number of Signalling Link Selectors is 16 for ITU and 256 for ANSI. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 0..255 | ||
| CItpTcSs7Variant | |||
| The list of SS7 variants. 'ANSI' : The ANSI variant of the SS7 specification. 'ITU' : The ITU variant of the SS7 specification. 'China' : The China national variant. This variant is a combination of ITU and ANSI. The protocol matches ITU except where the point-code has been expanded to ANSI format. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | ansi(1), itu(2), china(3) | ||
| CItpTcSubSystemNumber | |||
| The SCCP Subsystem Number . A value of zero indicates that a subsystem is not specified. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 0 | 2..255 | ||
| CItpTcSubSystemNumberMask | |||
| The SCCP Subsystem Number Mask. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 2..255 | ||
| CItpTcTableLoadStatus | |||
| The status of the current or prior load operation. 'loadNotRequested' : load operations have not been requested. 'loadInProgress' : load request is active. 'loadComplete' : load request complete without errors. 'loadCompleteWithErrors' : Load request completed with some type of errors that prevented the adding of one or more entries. 'loadFailed' : Load request failed. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | loadNotRequested(1), loadInProgress(2), loadComplete(3), loadCompleteWithErrors(4), loadFailed(5) | ||
| CItpTcTimerMtp2T01 | |||
| Alignment ready timer. The default and valid range is dependant on the value of variant. Min Max Def ------ ------ ------ ANSI 12500 16000 13000 ITU 40000 50000 40000 The SYNTAX statement allows values for both the ANSI, ITU variants and MTP2 Peer-to-Peer Adaptation Layer. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 5000..150000 | ||
| CItpTcTimerMtp2T02 | |||
| Not aligned timer. The default and valid range is dependant on the value of variant. This timer is only applicable if cItpTcLinkType is serial. A get on this object will return a zero if the link is not serial. Min Max Def ------ ------ ------ ANSI 5000 14000 11500 ITU 5000 150000 5000 The SYNTAX statement allows values for both the ANSI and ITU variants. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 0 | 5000..150000 | ||
| CItpTcTimerMtp2T03 | |||
| Aligned timer. The default and valid range is dependant on the value of variant. This timer is only applicable if cItpTcLinkType is serial. A get on this object will return a zero if the link is not serial. Min Max Def ------ ------ ------ ANSI 5000 14000 11500 ITU 1000 2000 1500 The SYNTAX statement allows values for both the ANSI and ITU variants. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 0 | 1000..14000 | ||
| CItpTcTimerMtp2T04E | |||
| Proving period timer emergency timer. The default and valid range is dependant on the value of variant. This timer is only applicable if cItpTcLinkType is serial. A get on this object will return a zero if the link is not serial. Min Max Def ------ ------ ------ ANSI 540 660 600 ITU 400 600 500 The SYNTAX statement allows values for both the ANSI and ITU variants. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 0 | 400..660 | ||
| CItpTcTimerMtp2T04N | |||
| Proving period timer normal timer. The default and valid range is dependant on the value of variant. This timer is only applicable if cItpTcLinkType is serial. A get on this object will return a zero if the link is not serial. Min Max Def ------ ------ ------ ANSI 2007 2530 2300 ITU 7500 9500 8200 The SYNTAX statement allows values for both the ANSI and ITU variants. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 0 | 2007..9500 | ||
| CItpTcTimerMtp2T05 | |||
| Sending SIB timer. The default and valid range is dependant on the value of variant. This timer is only applicable if cItpTcLinkType is serial. A get on this object will return a zero if the link is not serial. Min Max Def ------ ------ ------ ANSI 80 120 80 ITU 80 120 100 The SYNTAX statement allows values for both the ANSI and ITU variants. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 0 | 80..120 | ||
| CItpTcTimerMtp2T06 | |||
| Remote congestion timer. The default and valid range is dependant on the value of variant. Min Max Def ------ ------ ------ ANSI 1000 6000 1000 ITU 3000 6000 3000 The SYNTAX statement allows values for both the ANSI, ITU variants and MTP2 Peer-to-Peer Adaptation Layer. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 1000..6000 | ||
| CItpTcTimerMtp2T07 | |||
| Excessive delay of acknowledgement timer. The default and valid range is dependant on the value of variant(). This timer is only applicable if cItpTcLinkType is serial. A get on this object will return a zero if the link is not serial. Min Max Def ------ ------ ------ ANSI 500 2000 1000 ITU 500 2000 1000 The SYNTAX statement allows values for both the ANSI and ITU variants. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 0 | 100..6000 | ||
| CItpTcTimerMtp3T01 | |||
| Delay to avoid message mis-sequencing on changeover. Ranges by variant. Min Max Def ------ ------ ------ ANSI 500 1200 800 ITU 500 1200 800 The SYNTAX statement allows values for both the ANSI and ITU variants. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 500..1200 | ||
| CItpTcTimerMtp3T02 | |||
| Waiting for changeover acknowledgement. Ranges by variant. Min Max Def ------ ------ ------ ANSI 700 2000 1400 ITU 700 2000 1400 The SYNTAX statement allows values for both the ANSI and ITU variants. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 700..2000 | ||
| CItpTcTimerMtp3T03 | |||
| Time controlled diversion-delay to avoid mis-sequencing on change back. Ranges by variant. Min Max Def ------ ------ ------ ANSI 500 1200 800 ITU 500 1200 800 The SYNTAX statement allows values for both the ANSI and ITU variants. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 500..1200 | ||
| CItpTcTimerMtp3T04 | |||
| Waiting for change back acknowledgement (first attempt). Ranges by variant. Min Max Def ------ ------ ------ ANSI 500 1200 800 ITU 500 1200 800 The SYNTAX statement allows values for both the ANSI and ITU variants. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 500..1200 | ||
| CItpTcTimerMtp3T05 | |||
| Waiting for change back acknowledgement (second attempt). Ranges by variant. Min Max Def ------ ------ ------ ANSI 500 1200 800 ITU 500 1200 800 The SYNTAX statement allows values for both the ANSI and ITU variants. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 500..1200 | ||
| CItpTcTimerMtp3T06 | |||
| Delay to avoid message mis-sequencing on controlled rerouting. Ranges by variant. Min Max Def ------ ------ ------ ANSI 500 1200 800 ITU 500 1200 800 The SYNTAX statement allows values for both the ANSI and ITU variants. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 500..1200 | ||
| CItpTcTimerMtp3T07 | |||
| Waiting for Signalling data link connection acknowledgement. Ranges by variant. Min Max Def ------ ------ ------ ANSI 1000 2000 1500 ITU 1000 2000 1500 The SYNTAX statement allows values for both the ANSI and ITU variants. A value of zero indicates a value is not defined for a particular variant or is not supported by the implementation. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 0 | 1000..2000 | ||
| CItpTcTimerMtp3T08 | |||
| Transfer prohibited inhibition timer (transient solution). Ranges by variant. Min Max Def ------ ------ ------ ANSI 800 1200 1000 ITU 800 1200 1000 The SYNTAX statement allows values for both the ANSI and ITU variants. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 800..1200 | ||
| CItpTcTimerMtp3T10 | |||
| Waiting to repeat Signalling routeset test message. Ranges by variant. Min Max Def ------ ------ ------ ANSI 30000 60000 45000 ITU 30000 60000 45000 The SYNTAX statement allows values for both the ANSI and ITU variants. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 30000..60000 | ||
| CItpTcTimerMtp3T11 | |||
| Transfer restricted timer. (This is one way of implementing the function described in 13.4/Q.704 and mainly intended to simplify SPs.). Ranges by variant. Min Max Def ------ ------ ------ ANSI 30000 90000 60000 ITU 30000 90000 60000 The SYNTAX statement allows values for both the ANSI and ITU variants. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 30000..90000 | ||
| CItpTcTimerMtp3T12 | |||
| Waiting for uninhibit acknowledgement. Ranges by variant. Min Max Def ------ ------ ------ ANSI 800 1500 1150 ITU 800 1500 1150 The SYNTAX statement allows values for both the ANSI and ITU variants. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 800..1500 | ||
| CItpTcTimerMtp3T13 | |||
| Waiting for force uninhibit. Ranges by variant. Min Max Def ------ ------ ------ ANSI 800 1500 1150 ITU 800 1500 1150 The SYNTAX statement allows values for both the ANSI and ITU variants. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 800..1500 | ||
| CItpTcTimerMtp3T14 | |||
| Waiting for inhibition acknowledgement. Ranges by variant. Min Max Def ------ ------ ------ ANSI 2000 3000 2500 ITU 2000 3000 2500 The SYNTAX statement allows values for both the ANSI and ITU variants. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 2000..3000 | ||
| CItpTcTimerMtp3T15 | |||
| Waiting to start Signalling routeset congestion test. Ranges by variant. Min Max Def ------ ------ ------ ANSI 2000 3000 2500 ITU 2000 3000 2500 The SYNTAX statement allows values for both the ANSI and ITU variants. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 2000..3000 | ||
| CItpTcTimerMtp3T16 | |||
| Waiting for routeset congestion status update. Ranges by variant. Min Max Def ------ ------ ------ ANSI 1400 2000 1700 ITU 1400 2000 1700 The SYNTAX statement allows values for both the ANSI and ITU variants. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 1400..2000 | ||
| CItpTcTimerMtp3T17 | |||
| Delay to avoid oscillation of initial alignment failure and link restart. Ranges by variant. Min Max Def ------ ------ ------ ANSI 800 1500 1150 ITU 800 1500 1150 The SYNTAX statement allows values for both the ANSI and ITU variants. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 800..1500 | ||
| CItpTcTimerMtp3T18 | |||
| This timers servers different function based on the variant. ANSI: Repeat TFR once by response method ITU: MTP restart link supervision Min Max Def ------ ------ ------ ANSI 2000 20000 11000 ITU 1000 31000 30000 The SYNTAX statement allows values for both the ANSI and ITU variants. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 1000..31000 | ||
| CItpTcTimerMtp3T19 | |||
| This timers servers different function based on the variant. ANSI: failed craft timer referral timer ITU: supervision timer during MTP restart Min Max Def ------ ------ ------ ANSI 480000 600000 540000 ITU 67000 69000 68000 The SYNTAX statement allows values for both the ANSI and ITU variants. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 67000..600000 | ||
| CItpTcTimerMtp3T20 | |||
| This timers servers different function based on the variant. ANSI: waiting to repeat local inhibit test ITU: MTP restart timer at the Signalling point Min Max Def ------ ------ ------ ANSI 90000 120000 105000 ITU 1000 61000 60000 The SYNTAX statement allows values for both the ANSI and ITU variants. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 1000..120000 | ||
| CItpTcTimerMtp3T21 | |||
| This timers servers different function based on the variant. ANSI: waiting to repeat remote inhibit test) ITU: MTP restart timer at adjacent Signalling point Min Max Def ------ ------ ------ ANSI 90000 120000 105000 ITU 63000 65000 64000 The SYNTAX statement allows values for both the ANSI and ITU variants. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 63000..120000 | ||
| CItpTcTimerMtp3T22 | |||
| This timers servers different function based on the variant. ANSI: restarting SP waiting for Signalling links avail ITU: local inhibit test timer Min Max Def ------ ------ ------ ANSI 36000 60000 30000 ITU 80000 360000 300000 The SYNTAX statement allows values for both the ANSI and ITU variants. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 36000..360000 | ||
| CItpTcTimerMtp3T23 | |||
| This timers servers different function based on the variant. ANSI: restarting SP waiting to receive all TRA msgs ITU: remote inhibit test timer Min Max Def ------ ------ ------ ANSI 9000 60000 30000 ITU 80000 360000 300000 The SYNTAX statement allows values for both the ANSI and ITU variants. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 9000..360000 | ||
| CItpTcTimerMtp3T24 | |||
| This timers servers different function based on the variant. ANSI: restarting SP waiting to broadcast all TRA msgs ITU: stabilizing timer after local processor outage Min Max Def ------ ------ ------ ANSI 9000 60000 30000 ITU 500 500 500 The SYNTAX statement allows values for both the ANSI and ITU variants. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 500..60000 | ||
| CItpTcTimerMtp3T25 | |||
| Timer at Signalling Point (SP) adjacent to restarting SP, waiting for traffic restart allowed message. Ranges by variant. Min Max Def ------ ------ ------ ANSI 30000 35000 30000 This timer is not used when the variant is ITU. A value of zero indicates a value is not defined for a particular variant or is not supported by the implementation. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 0 | 30000..35000 | ||
| CItpTcTimerMtp3T26 | |||
| Timer at restarting SP waiting to repeat traffic restart waiting message. Ranges by variant. Min Max Def ------ ------ ------ ANSI 12000 15000 12000 This timer is not used when the variant is ITU. A value of zero indicates a value is not defined for a particular variant or is not supported by the implementation. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 0 | 12000..15000 | ||
| CItpTcTimerMtp3T27 | |||
| Minimum duration of unavailability for full restart. Ranges by variant. Min Max Def ------ ------ ------ ANSI 2000 50000 4000 This timer is not used when the variant is ITU. A value of zero indicates a value is not defined for a particular variant or is not supported by the implementation. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 0 | 2000..50000 | ||
| CItpTcTimerMtp3T28 | |||
| Timer at SP adjacent to restarting SP waiting for traffic restart waiting message. Ranges by variant. Min Max Def ------ ------ ------ ANSI 3000 35000 30000 This timer is not used when the variant is ITU. A value of zero indicates a value is not defined for a particular variant or is not supported by the implementation. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 0 | 3000..35000 | ||
| CItpTcTimerMtp3T29 | |||
| Timer started when TRA sent in response to unexpected TRA or TRW. Ranges by variant. Min Max Def ------ ------ ------ ANSI 60000 65000 63000 This timer is not used when the variant is ITU. A value of zero indicates a value is not defined for a particular variant or is not supported by the implementation. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 0 | 60000..65000 | ||
| CItpTcTimerMtp3T30 | |||
| Timer to limit sending of TFPs and TFRs in response to unexpected TRA or TRW. Ranges by variant. Min Max Def ------ ------ ------ ANSI 30000 35000 33000 This timer is not used when the variant is ITU. A value of zero indicates a value is not defined for a particular variant or is not supported by the implementation. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 0 | 30000..35000 | ||
| CItpTcTimerMtp3T31 | |||
| False link congestion detection timer. Ranges by variant. Min Max Def ------ ------ ------ ANSI 10000 120000 60000 This timer is not used when the variant is ITU. A value of zero indicates a value is not defined for a particular variant or is not supported by the implementation. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 0 | 10000..120000 | ||
| CItpTcTimerMtp3T32 | |||
| Link oscillation timer - Procedure A. Ranges by variant. Min Max Def ------ ------ ------ ANSI 5000 120000 60000 This timer is not used when the variant is ITU. A value of zero indicates a value is not defined for a particular variant or is not supported by the implementation. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 0 | 5000..120000 | ||
| CItpTcTimerMtp3T33 | |||
| Probation timer for link oscillation - Procedure B. Ranges by variant. Min Max Def ------ ------ ------ ANSI 60000 600000 300000 This timer is not used when the variant is ITU. A value of zero indicates a value is not defined for a particular variant or is not supported by the implementation. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 0 | 60000..600000 | ||
| CItpTcTimerMtp3T34 | |||
| Suspension timer for link oscillation - Procedure B. Ranges by variant. Min Max Def ------ ------ ------ ANSI 5000 120000 60000 This timer is not used when the variant is ITU. A value of zero indicates a value is not defined for a particular variant or is not supported by the implementation. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 0 | 5000..120000 | ||
| CItpTcTimerLinkTest | |||
| Signalling Link test acknowledgement timer. Min Max Def ------ ------ ------ ANSI 4000 12000 8000 This timer is not used when the variant is ITU. A value of zero indicates a value is not defined for a particular variant or is not supported by the implementation. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 0 | 4000..12000 | ||
| CItpTcTimerLinkMessage | |||
| Interval timer for sending test messages. Min Max Def ------ ------ ------ ANSI 30000 90000 60000 This timer is not used when the variant is ITU. A value of zero indicates a value is not defined for a particular variant or is not supported by the implementation. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 0 | 30000..90000 | ||
| CItpTcTimerLinkActRetry | |||
| Link activation retry timer. Min Max Def ------ ------ ------ ANSI 60000 90000 60000 This timer is not used when the variant is ITU. A value of zero indicates a value is not defined for a particular variant or is not supported by the implementation. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 0 | 60000..90000 | ||
| CItpTcTranslationType | |||
| The Translation Type for SCCP GTT GTA specifies Title Translation or Subsystem Number (SSN) 'tt' : The GTT GTA has specified Title Translation 'ssn' : The GTT GTA has specified Subsystem Number. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | tt(1), ssn(2) | ||
| CItpTcURL | |||
| The URL used to load a configuration file. An octet string specified by an administrator that must be in human-readable form. The names must conform to the allowed characters that can be specified via Command Line Interface(CLI). The names cannot contain control character and should not contain leading or trailing white space. | |||
| TEXTUAL-CONVENTION | |||
| OCTET STRING | SIZE(0..255) | ||
| CItpTcXuaName | |||
| The configured name associated with M3UA/SUA ASP or AS name. An octet string specified by an administrator that must be in human-readable form. The names must conform to the allowed characters that can be specified via Command Line Interface(CLI). The names cannot contain control character and should not contain leading or trailing white space. | |||
| TEXTUAL-CONVENTION | |||
| OCTET STRING | SIZE(0..12) | ||