CISCO-L2L3-INTERFACE-CONFIG-MIB

File: CISCO-L2L3-INTERFACE-CONFIG-MIB.mib (5337 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
IF-MIB CISCO-SMI

Imported symbols

MODULE-IDENTITY OBJECT-TYPE MODULE-COMPLIANCE
OBJECT-GROUP TEXTUAL-CONVENTION ifIndex
ciscoMgmt

Defined Objects

ciscoL2L3IfConfigMIB 1.3.6.1.4.1.9.9.151
Interface switchport mode configuration management MIB. This MIB is used to monitor and control configuration of interface switchport and routed mode.
MODULE-IDENTITY    

ciscoL2L3IfConfigMIBObjects 1.3.6.1.4.1.9.9.151.1
OBJECT IDENTIFIER    

cL2L3IfConfig 1.3.6.1.4.1.9.9.151.1.1
OBJECT IDENTIFIER    

cL2L3IfTable 1.3.6.1.4.1.9.9.151.1.1.1
The table shows the administratively requested and actual operating configuration for switchport interfaces.
OBJECT-TYPE    
  SEQUENCE OF  
    CL2L3IfEntry

cL2L3IfEntry 1.3.6.1.4.1.9.9.151.1.1.1.1
An entry represents the configuration and operation of a switchport interface. Entries are created and deleted automatically in tandem with the corresponding ifEntries.
OBJECT-TYPE    
  CL2L3IfEntry  

cL2L3IfModeAdmin 1.3.6.1.4.1.9.9.151.1.1.1.1.1
The administratively desired interface mode.
OBJECT-TYPE    
  CL2L3InterfaceMode  

cL2L3IfModeOper 1.3.6.1.4.1.9.9.151.1.1.1.1.2
The operational interface mode.
OBJECT-TYPE    
  CL2L3InterfaceMode  

ciscoL2L3IfConfigMIBConformance 1.3.6.1.4.1.9.9.151.3
OBJECT IDENTIFIER    

ciscoL2L3IfConfigMIBCompliances 1.3.6.1.4.1.9.9.151.3.1
OBJECT IDENTIFIER    

ciscoL2L3IfConfigMIBCompliance 1.3.6.1.4.1.9.9.151.3.1.1
The compliance statement for entities which implement the Cisco L2L3 Interface Configuration Management MIB
MODULE-COMPLIANCE    

ciscoL2L3IfConfigMIBGroups 1.3.6.1.4.1.9.9.151.3.2
OBJECT IDENTIFIER    

ciscoL2L3IfConfigMIBGroup 1.3.6.1.4.1.9.9.151.3.2.1
Interface L2 & L3 mode objects
OBJECT-GROUP    

Defined Objects

CL2L3InterfaceMode  
The operational mode of the interface. For administrative and operational states, valid values are: routed(1), switchport(2). routed(1): Routed mode interfaces direct traffic using layer 3 protocols. switchport(2): Switchport-mode interfaces direct traffic using layer 2 protocols. A switchport-mode interface can be in access mode, or trunk mode, or multi-mode. Switchport interface operating mode can be configured manually, or negotiated by Dynamic Trunking Protocol (DTP) or Dynamic Inter-Switch Link (DISL). Access-mode interfaces carry one VLAN's traffic. Access-mode interface parameters are configured in CISCO-VLAN-MEMBERSHIP-MIB. Trunk-mode interfaces carry one or more VLANs. VLAN-related trunk-mode interface parameters are configured in CISCO-VTP-MIB. Multi-mode interfaces carry one VLAN to each alias of a single connected end-station. VLAN-related multi-mode interface parameters are configured in CISCO-VTP-MIB.
TEXTUAL-CONVENTION    
  INTEGER routed(1), switchport(2)  

CL2L3IfEntry  
SEQUENCE    
  CL2L3InterfaceMode as cL2L3IfModeAdmin  
  CL2L3InterfaceMode as cL2L3IfModeOper