CISCO-L4L7MODULE-RESOURCE-LIMIT-MIB

File: CISCO-L4L7MODULE-RESOURCE-LIMIT-MIB.mib (45271 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
ENTITY-MIB CISCO-SMI

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Unsigned32
Gauge32 Counter32 Counter64
NOTIFICATION-TYPE MODULE-COMPLIANCE OBJECT-GROUP
NOTIFICATION-GROUP TruthValue TEXTUAL-CONVENTION
RowStatus StorageType TimeStamp
entPhysicalIndex ciscoMgmt

Defined Objects

ciscoL4L7moduleResourceLimitMIB 1.3.6.1.4.1.9.9.480
The MIB module for managing resource classes and configuring limits(max/min) to different resources. The resource referenced in this MIB are in addition to resource information availale in other MIBs. This MIB is applicable to L4-L7 modules which supports managing resource limits using a centralized approach. The resources (but not limited to) configured are of following categories: - TCP/IP Connections - MAC Addresses - syslog buffer, ACL Memmory - NAT Translations etc ciscoL4L7ResourceClassTable is used for adding/deleting resource classes. Resource class is identified by a name to which limits of multiple resources can be configured. ciscoL4L7ResourceLimitTable is used for adding/deleting limits to resources in a resource class. This limit is either maximum value and/or minimum value. ciscoL4L7ResourceRateLimitTable is used for adding/deleting rate limits to resources in a resource class. Terminologies used: ARP - Address Resolution Protocol. ACL - Access Control List. NAT - Network Address Translation. NBAR - Network Based Application Recognition. BPDU - Bridge Protocol Data Unit.
MODULE-IDENTITY    

ciscoL4L7ResourceLimitNotifs 1.3.6.1.4.1.9.9.480.0
OBJECT IDENTIFIER    

clrResourceLimitReached 1.3.6.1.4.1.9.9.480.0.1
This notification is generated when the configured resource limit value specified in 'crlResourceLimitMax' is reached for a particular resource. This resource is identified by 'crlResourceLimitType' in ciscoL4L7ResourceLimitTable.
NOTIFICATION-TYPE    
  crlResourceLimitValueType  
  crlResourceLimitMax  

clrResourceRateLimitReached 1.3.6.1.4.1.9.9.480.0.2
This notification is generated when the configured rate limit value specified in 'crlRateLimitResourceMax' is reached for a particular resource. This resource is identified by 'crlRateLimitResourceType' in ciscoL4L7ResourceRateLimitTable.
NOTIFICATION-TYPE    
  crlRateLimitResourceMax  

ciscoL4L7ResourceLimitMIBObjects 1.3.6.1.4.1.9.9.480.1
OBJECT IDENTIFIER    

crlResource 1.3.6.1.4.1.9.9.480.1.1
OBJECT IDENTIFIER    

ciscoL4L7ResourceClassTable 1.3.6.1.4.1.9.9.480.1.1.1
This table contains one row per resource class. This table is used for adding/deleting the resource class in the system. A resource class can contain limits for different category of resources and these resources can be configured using other tables.
OBJECT-TYPE    
  SEQUENCE OF  
    CiscoL4L7ResourceClassEntry

ciscoL4L7ResourceClassEntry 1.3.6.1.4.1.9.9.480.1.1.1.1
Information about a particular resource class. Each entry provides the name of class. The entPhysicalIndex refers to resource manageable component in entPhysicalTable with entPhysicalClass -> 'module'.
OBJECT-TYPE    
  CiscoL4L7ResourceClassEntry  

crlResourceClassName 1.3.6.1.4.1.9.9.480.1.1.1.1.1
This object identifies a unique resource class in a resource manageable component identified by entPhysicalIndex.
OBJECT-TYPE    
  CiscoResourceClass  

crlResourceClassStorageType 1.3.6.1.4.1.9.9.480.1.1.1.1.2
The storage type for this conceptual row. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row. This object can not be modified when the value of crlResourceClassRowStatus is 'active'.
OBJECT-TYPE    
  StorageType  

crlResourceClassRowStatus 1.3.6.1.4.1.9.9.480.1.1.1.1.3
This object is used for adding/deleting resource classes in a system.
OBJECT-TYPE    
  RowStatus  

ciscoL4L7ResourceLimitTable 1.3.6.1.4.1.9.9.480.1.1.2
This table is used for adding resource limits to resources in a resource class.
OBJECT-TYPE    
  SEQUENCE OF  
    CiscoL4L7ResourceLimitEntry

ciscoL4L7ResourceLimitEntry 1.3.6.1.4.1.9.9.480.1.1.2.1
Information about a particular resource in a resource class. Each entry provides the type of resource, the limit that is supported for that resource and type of the limit value.
OBJECT-TYPE    
  CiscoL4L7ResourceLimitEntry  

crlResourceLimitType 1.3.6.1.4.1.9.9.480.1.1.2.1.2
This object represents the type of resource in a resource class identified by crlResourceClassName.
OBJECT-TYPE    
  CiscoResourceLimitType  

crlResourceLimitValueType 1.3.6.1.4.1.9.9.480.1.1.2.1.3
This object represents the type of value specified in crlResourceLimitMax and crlResourceLimitMin objects. The possible values are : absolute (1) : the value represents an absolute number. percentage (2) : the value represents the % of the total available for the system. In this case only crlResourceLimitMax object is applicable.
OBJECT-TYPE    
  INTEGER absolute(1), percentage(2)  

crlResourceLimitMin 1.3.6.1.4.1.9.9.480.1.1.2.1.4
This object represents the rate limit allowed for the resource identified by 'ciscoResourceLimitType'. This value cannot be greater than the value specified in ciscoResourceLimitMax. The value zero signifies that this object is not applicable to the resource.
OBJECT-TYPE    
  Unsigned32  

crlResourceLimitMax 1.3.6.1.4.1.9.9.480.1.1.2.1.5
This object represents the limit allowed for the resource identified by 'ciscoResourceLimitType'. The value zero specifies that this resource can be used until the system limit reached.
OBJECT-TYPE    
  Unsigned32  

crlResourceLimitStorageType 1.3.6.1.4.1.9.9.480.1.1.2.1.6
The storage type for this conceptual row. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row. This object cannot be modified when the value of crlResourceLimitRowStatus is 'active'.
OBJECT-TYPE    
  StorageType  

crlResourceLimitRowStatus 1.3.6.1.4.1.9.9.480.1.1.2.1.7
This object is used for adding/deleting entries in this table.
OBJECT-TYPE    
  RowStatus  

crlResourceLimitCurrentUsage 1.3.6.1.4.1.9.9.480.1.1.2.1.8
This object indicates the number of resources identified by 'ciscoResourceLimitType', that are currently being used in the system.
OBJECT-TYPE    
  Gauge32  

crlResourceLimitPeakUsage 1.3.6.1.4.1.9.9.480.1.1.2.1.9
This object represents the peak usage of the resource identified by 'ciscoResourceLimitType' since the statistics were last cleared either through the command line interface or bacause of the system reboot.
OBJECT-TYPE    
  Gauge32  

crlResourceLimitReqsDeniedCount 1.3.6.1.4.1.9.9.480.1.1.2.1.10
This object represents the number of resource requests that were denied when the configured resource limit is exceeded for the resource identified by 'ciscoResourceLimitType'. The value for resource limiting is specified in 'crlResourceLimitMax'.
OBJECT-TYPE    
  Counter32  

ciscoL4L7ResourceRateLimitTable 1.3.6.1.4.1.9.9.480.1.1.4
This table is used for adding/deleting the rate limiting of the resources in a resource class.
OBJECT-TYPE    
  SEQUENCE OF  
    CiscoL4L7ResourceRateLimitEntry

ciscoL4L7ResourceRateLimitEntry 1.3.6.1.4.1.9.9.480.1.1.4.1
Information about an entry in the table Each entry provides the name of group, the rate configured for a resource.
OBJECT-TYPE    
  CiscoL4L7ResourceRateLimitEntry  

crlRateLimitResourceType 1.3.6.1.4.1.9.9.480.1.1.4.1.1
This object represents the resource type for which rate limiting needs to be done. The value for rate limiting is specified in crlRateLimitResourceMin and crlRateLimitResourceMax.
OBJECT-TYPE    
  CiscoRateLimitResourceType  

crlRateLimitResourceMin 1.3.6.1.4.1.9.9.480.1.1.4.1.2
This object represents the rate limit allowed for the resource identified by 'crlRateLimitResourceType'. This value cannot be greater than the value specified in crlRateLimitResourceMax. The value zero signifies that this object is not applicable to the resource.
OBJECT-TYPE    
  Unsigned32  

crlRateLimitResourceMax 1.3.6.1.4.1.9.9.480.1.1.4.1.3
This object represents the limit allowed for the resource identified by 'crlRateLimitResourceType'. The value zero specifies that this resource can be used until the system limit reached.
OBJECT-TYPE    
  Unsigned32  

crlRateLimitResourceStorageType 1.3.6.1.4.1.9.9.480.1.1.4.1.4
The storage type for this conceptual row. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row. This object cannot be modified when the value of crlRateLimitResourceRowStatus is 'active'.
OBJECT-TYPE    
  StorageType  

crlRateLimitResourceRowStatus 1.3.6.1.4.1.9.9.480.1.1.4.1.5
This object is used for adding/deleting entries in this table. This object cannot be set to 'active' until all the mandatory objects have valid value.
OBJECT-TYPE    
  RowStatus  

crlRateLimitResourceCurrentUsage 1.3.6.1.4.1.9.9.480.1.1.4.1.6
This object indicates the number of resources identified by 'crlRateLimitResourceType', that are currently being used in the system.
OBJECT-TYPE    
  Gauge32  

crlRateLimitResourcePeakUsage 1.3.6.1.4.1.9.9.480.1.1.4.1.7
This object represents the peak usage of the resource identified by 'crlRateLimitResourceType' since the statistics were last cleared either through the command line interface or bacause of the system reboot.
OBJECT-TYPE    
  Gauge32  

crlRateLimitResourceReqsDeniedCount 1.3.6.1.4.1.9.9.480.1.1.4.1.8
This object represents the number of resource requests that were denied when the configured rate limit is exceeded for the resource identified by 'crlRateLimitResourceType'. The value for rate limiting is specified in 'crlRateLimitResourceMax'.
OBJECT-TYPE    
  Counter32  

ciscoL4L7ResourceUsageSummaryTable 1.3.6.1.4.1.9.9.480.1.1.5
This table provides the statistics for each resource type in a system. The resource usage statistics can be: - current usage for the resource. - peak usage for the resource. - Number of times the resource request were denied when the configured limit or rate-limit is exceeded for the resource.
OBJECT-TYPE    
  SEQUENCE OF  
    CiscoL4L7ResourceUsageSummaryEntry

ciscoL4L7ResourceUsageSummaryEntry 1.3.6.1.4.1.9.9.480.1.1.5.1
An entry in ciscoL4L7ResourceUsageSummaryTable. Each entry provides the resource usage parameters in a system. An entry is created when an entry is created in either 'ciscoL4L7ResourceLimitTable' or 'ciscoL4L7ResourceRateLimitTable'. An entry is deleted when an entry is deleted from either 'ciscoL4L7ResourceLimitTable' or 'ciscoL4L7ResourceRateLimitTable'.
OBJECT-TYPE    
  CiscoL4L7ResourceUsageSummaryEntry  

crlResourceSummaryType 1.3.6.1.4.1.9.9.480.1.1.5.1.1
This object represents a type of resource in the system.
OBJECT-TYPE    
  CiscoResourceType  

crlResourceSummaryCurrentUsage 1.3.6.1.4.1.9.9.480.1.1.5.1.2
This object indicates the current usage of the resource in the system.
OBJECT-TYPE    
  Gauge32  

crlResourceSummaryPeakUsage 1.3.6.1.4.1.9.9.480.1.1.5.1.3
This object represents the peak usage of the resource in the system.
OBJECT-TYPE    
  Gauge32  

crlResourceSummaryReqsDeniedCount 1.3.6.1.4.1.9.9.480.1.1.5.1.4
This object represents the number of resource requests that were denied in the system when the configured limit is exceeded for the resource. The value for limiting is specified in 'crlResourceLimitMax' and the value for rate limiting is specified in 'crlRateLimitResourceMax'.
OBJECT-TYPE    
  Counter64  

crlResourceSummaryLastClearedTime 1.3.6.1.4.1.9.9.480.1.1.5.1.5
This object represents the time when the value of the object identified by 'crlResourceSummaryPeakUsage' is last cleared or reset. A value of 0 (zero) signifies that the value has not been cleared since the last system reboot.
OBJECT-TYPE    
  TimeStamp  

crlResourceSummaryStorageType 1.3.6.1.4.1.9.9.480.1.1.5.1.6
The storage type for this conceptual row. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row. This object cannot be modified when the value of 'crlResourceSummaryRowStatus' is 'active'.
OBJECT-TYPE    
  StorageType  

crlResourceSummaryRowStatus 1.3.6.1.4.1.9.9.480.1.1.5.1.7
This object is used for adding/deleting entries in this table. This object cannot be set to 'active' until all the mandatory objects have valid value.
OBJECT-TYPE    
  RowStatus  

crlNotificationObjects 1.3.6.1.4.1.9.9.480.1.2
OBJECT IDENTIFIER    

clrResourceLimitReachedNotifEnabled 1.3.6.1.4.1.9.9.480.1.2.1
This object controls the generation of 'clrResourceLimitReached' notification. 'true' Indicates that clrResourceLimitReached notification is to be generated when the configured resource limit is reached. The value for resource limiting is specified in 'crlResourceLimitMax'. 'false' Indicates that clrResourceLimitReached notification generation is disabled.
OBJECT-TYPE    
  TruthValue  

clrResourceRateLimitReachedNotifEnabled 1.3.6.1.4.1.9.9.480.1.2.2
This object controls the generation of 'clrResourceRateLimitReached' notification. 'true' Indicates that clrResourceRateLimitReached notification is to be generated when the configured resource rate limit is reached. The value for rate limiting is specified in 'crlRateLimitResourceMax'. 'false' Indicates that clrResourceRateLimitReached notification generation is disabled.
OBJECT-TYPE    
  TruthValue  

ciscoResourceLimitMIBConform 1.3.6.1.4.1.9.9.480.2
OBJECT IDENTIFIER    

ciscoL4L7ResourceLimitConformance 1.3.6.1.4.1.9.9.480.3
OBJECT IDENTIFIER    

ciscoL4L7ResourceLimitCompliances 1.3.6.1.4.1.9.9.480.3.1
OBJECT IDENTIFIER    

ciscoL4L7ResourceLimitCompliance 1.3.6.1.4.1.9.9.480.3.1.1
The compliance statement for SNMP entities which implement CISCO-L4L7MODULE-RESOURCE-LIMIT-MIB.
MODULE-COMPLIANCE    

ciscoL4L7ResourceLimitComplianceRev1 1.3.6.1.4.1.9.9.480.3.1.2
The compliance statement for SNMP entities which implement CISCO-L4L7MODULE-RESOURCE-LIMIT-MIB.
MODULE-COMPLIANCE    

ciscoL4L7ResourceLimitComplianceRev2 1.3.6.1.4.1.9.9.480.3.1.3
The compliance statement for SNMP entities which implement CISCO-L4L7MODULE-RESOURCE-LIMIT-MIB.
MODULE-COMPLIANCE    

ciscoL4L7ResourceLimitGroups 1.3.6.1.4.1.9.9.480.3.2
OBJECT IDENTIFIER    

ciscoL4L7ResourceClassGroup 1.3.6.1.4.1.9.9.480.3.2.1
The collection of objects which are used to represent resource class in a system.
OBJECT-GROUP    

ciscoL4L7ResourceLimitGroup 1.3.6.1.4.1.9.9.480.3.2.2
The collection of objects which are used to represent limits of resources in a resource class.
OBJECT-GROUP    

ciscoL4L7ResourceRateLimitGroup 1.3.6.1.4.1.9.9.480.3.2.3
The collection of objects which are used to represent rate limits for resources.
OBJECT-GROUP    

ciscoL4L7ResourceLimitUsageGroup 1.3.6.1.4.1.9.9.480.3.2.4
The collection of objects which are used to represent limit usage for resources.
OBJECT-GROUP    

ciscoL4L7ResourceRateLimitUsageGroup 1.3.6.1.4.1.9.9.480.3.2.5
The collection of objects which are used to represent rate limit usage for resources.
OBJECT-GROUP    

ciscoL4L7ResourceNotifEnabledGroup 1.3.6.1.4.1.9.9.480.3.2.6
The collection of objects which are used to represent limit usage for resources.
OBJECT-GROUP    

ciscoL4L7ResourceNotifGroup 1.3.6.1.4.1.9.9.480.3.2.7
The collection of objects which are used to represent rate limit usage for resources.
NOTIFICATION-GROUP    

ciscoL4L7ResourceUsageSummaryGroup 1.3.6.1.4.1.9.9.480.3.2.8
The collection of objects which are used to represent usage summary for resources across the system.
OBJECT-GROUP    

Defined Objects

CiscoResourceClass  
This textual convention is used for representing resource classes. A resource class is identified by a name preferably in human readable form. This resource class is used for identifying different type of resources. The resource class can represent single resource type or multiple resource type. Resource category examples: memory, connections NAT(network address translation) translations, number of syslog messages etc.
TEXTUAL-CONVENTION    
  OCTET STRING SIZE(0..64)  

CiscoResourceLimitType  
This object represents the resource type. The possible values are : all (1) : This is not a resource. However this value acts as the wild card value to set all the resources at the same time. If an entry exists with this value, then for all the resources that are not configured in this table will have the value specified in this entry. macAddresses(2) : The number of MAC addresses allowed in the MAC address table. concurrentConns (3) : Concurrent TCP/UDP connections that are supported. Connections exist between any two hosts. This is applicable for through the box connections only. mgmtConnections (4) : This is applicable for to-the-box traffic only. proxyConns (5) : Sticky connections limit traffic to the individual real servers by allowing multiple connections from the same client to stick (or attach) to the same real server using source IP addresses, source IP subnets, cookies, and the secure socket layer (SSL) or by redirecting these connections using Hypertext Transfer Protocol (HTTP) redirect messages. probes (6) : the number of health probes. stickyEntries (7) : the number of sticky entries. This refers to statically configured entries and dynamically created ones. It represents the pool of entries available for use/re-use. natTranslations (8) : the number of NAT Translations. regexState (9) : Regular expression state. Regex states are nodes in the regular expression state graph, used for matching and sticking on HTTP fields such as URL, header, cookies. aclMemory (10) : Memory that is allocated for managing ACLs. ipReassemBuffer (11) : buffer that is allocated for IP Reassembly. syslogBuffer (12) : buffer that is allocated for syslog messages that can be logged in the system. tcpOOOBuffer (13) : buffer that is allocated for TCP Out Of Order packets. sslConnections (14) : The number of SSL Connections. hosts (15) : Number of hosts allowed through the system. ipsecSessions (16) : Number of IPSec management sessions. asdmSessions (17) : Number of ASDM management sessions. sshSessions (18) : Number of SSH management sessions. telnetSessions (19) : Number of Telnet management sessions.
TEXTUAL-CONVENTION    
  INTEGER all(1), macAddresses(2), concurrentConns(3), mgmtConnections(4), proxyConns(5), probes(6), stickyEntries(7), natTranslations(8), regexState(9), aclMemory(10), syslogBuffer(11), ipReassemBuffer(12), tcpOOOBuffer(13), sslConnections(14), hosts(15), ipsecSessions(16), asdmSessions(17), sshSessions(18), telnetSessions(19)  

CiscoRateLimitResourceType  
This object represents the resource type for which rate limiting needs to be done. The value for rate limiting is specified in crlRateLimitResourceMin and crlRateLimitResourceMax. The possible value(s) are : all (1) : This value represents a wildcard value to mean all the resources. arpRequestsXmt (2) : ARP requests generated per second arpResponses (3) : ARP responses to received ARP requests per second. bandwidth (4) : Bandwidth of the card in bytes per second. connections (5) : connections per second. appInspections (6) : application inspections per second. syslog (7) : syslog messages per second. sslBandwidth (8) : SSL bandwidth in bytes per second. sslConnections (9) : SSL connections per second. mgmtBandwidth (10): Management (to-the-ACE) traffic in bytes per second. throughput (11): User (through-the-ACE) traffic in bytes per second. missedMac (12): Number of ARP resolution requests in packets per second. httpCompression (13): Compression rate for HTTP traffic in bytes per second.
TEXTUAL-CONVENTION    
  INTEGER all(1), arpRequestsXmt(2), arpResponses(3), bandwidth(4), connections(5), appInspections(6), syslog(7), sslBandwidth(8), sslConnections(9), mgmtBandwidth(10), throughput(11), missedMac(12), httpCompression(13)  

CiscoResourceType  
This object represents a resource type. The possible values for this object are: lMacAddresses (1) : Refer to 'macAddresses' in CiscoResourceLimitType. lConcurrentConns (2) : Refer to 'concurrentConns' in CiscoResourceLimitType. lMgmtConnections (3) : Refer to 'mgmtConnections' in CiscoResourceLimitType. lProxyConns (4) : Refer to 'proxyConns' in CiscoResourceLimitType. lProbes (5) : Refer to 'probes' in CiscoResourceLimitType. lStickyEntries (6) : Refer to 'stickyEntries' in CiscoResourceLimitType. lNatTranslations (7) : Refer to 'natTranslations' in CiscoResourceLimitType. lRegexState (8) : Refer to 'regexState' in CiscoResourceLimitType. lAclMemory (9) : Refer to 'aclMemory' in CiscoResourceLimitType. lIpReassemBuffer (10) : Refer to 'ipReassemBuffer' in CiscoResourceLimitType. lSyslogBuffer (11) : Refer to 'syslogBuffer' in CiscoResourceLimitType. lTcpOOOBuffer (12) : Refer to 'tcpOOOBuffer' in CiscoResourceLimitType. lSslConnections (13) : Refer to 'sslConnections' in CiscoResourceLimitType. lHosts (14) : Refer to 'hosts' in CiscoResourceLimitType. lIpsecSessions (15) : Refer to 'ipsecSessions' in CiscoResourceLimitType. lAsdmSessions (16) : Refer to 'asdmSessions' in CiscoResourceLimitType. lSshSessions (17) : Refer to 'sshSessions' in CiscoResourceLimitType. lTelnetSessions (18) : Refer to 'telnetSessions' in CiscoResourceLimitType. rlArpRequestsXmt (19) : Refer to 'arpRequestsXmt' in CiscoRateLimitResourceType. rlArpResponses (20) : Refer to 'arpResponses' in CiscoRateLimitResourceType. rlBandwidth (21) : Refer to 'bandwidth' in CiscoRateLimitResourceType. rlConnections (22) : Refer to 'connections' in CiscoRateLimitResourceType. rlAppInspections (23) : Refer to 'appInspections' in CiscoRateLimitResourceType. rlSyslog (24) : Refer to 'syslog' in CiscoRateLimitResourceType. rlSslBandwidth (25) : Refer to 'sslBandwidth' in CiscoRateLimitResourceType. rlSslConnections (26) : Refer to 'sslConnections' in CiscoRateLimitResourceType. rlMgmtBandwidth (27) : Refer to 'mgmtBandwidth' in CiscoRateLimitResourceType. rlThroughput (28) : Refer to 'throughput' in CiscoRateLimitResourceType. rlMissedMac (29) : Refer to 'missedMac' in CiscoRateLimitResourceType. rlHttpCompression (30) : Refer to 'httpCompression' in CiscoRateLimitResourceType.
TEXTUAL-CONVENTION    
  INTEGER lMacAddresses(1), lConcurrentConns(2), lMgmtConnections(3), lProxyConns(4), lProbes(5), lStickyEntries(6), lNatTranslations(7), lRegexState(8), lAclMemory(9), lIpReassemBuffer(10), lSyslogBuffer(11), lTcpOOOBuffer(12), lSslConnections(13), lHosts(14), lIpsecSessions(15), lAsdmSessions(16), lSshSessions(17), lTelnetSessions(18), rlArpRequestsXmt(19), rlArpResponses(20), rlBandwidth(21), rlConnections(22), rlAppInspections(23), rlSyslog(24), rlSslBandwidth(25), rlSslConnections(26), rlMgmtBandwidth(27), rlThroughput(28), rlMissedMac(29), rlHttpCompression(30)  

CiscoL4L7ResourceClassEntry  
SEQUENCE    
  CiscoResourceClass as crlResourceClassName  
  StorageType as crlResourceClassStorageType  
  RowStatus as crlResourceClassRowStatus  

CiscoL4L7ResourceLimitEntry  
SEQUENCE    
  CiscoResourceLimitType as crlResourceLimitType  
  INTEGER as crlResourceLimitValueType  
  Unsigned32 as crlResourceLimitMin  
  Unsigned32 as crlResourceLimitMax  
  StorageType as crlResourceLimitStorageType  
  RowStatus as crlResourceLimitRowStatus  
  Gauge32 as crlResourceLimitCurrentUsage  
  Gauge32 as crlResourceLimitPeakUsage  
  Counter32 as crlResourceLimitReqsDeniedCount  

CiscoL4L7ResourceRateLimitEntry  
SEQUENCE    
  CiscoRateLimitResourceType as crlRateLimitResourceType  
  Unsigned32 as crlRateLimitResourceMin  
  Unsigned32 as crlRateLimitResourceMax  
  StorageType as crlRateLimitResourceStorageType  
  RowStatus as crlRateLimitResourceRowStatus  
  Gauge32 as crlRateLimitResourceCurrentUsage  
  Gauge32 as crlRateLimitResourcePeakUsage  
  Counter32 as crlRateLimitResourceReqsDeniedCount  

CiscoL4L7ResourceUsageSummaryEntry  
SEQUENCE    
  CiscoResourceType as crlResourceSummaryType  
  Gauge32 as crlResourceSummaryCurrentUsage  
  Gauge32 as crlResourceSummaryPeakUsage  
  Counter64 as crlResourceSummaryReqsDeniedCount  
  TimeStamp as crlResourceSummaryLastClearedTime  
  StorageType as crlResourceSummaryStorageType  
  RowStatus as crlResourceSummaryRowStatus