CISCO-LWAPP-AP-MIB

File: CISCO-LWAPP-AP-MIB.mib (17380 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
SNMP-FRAMEWORK-MIB ENTITY-MIB CISCO-LWAPP-TC-MIB
CISCO-SMI

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Unsigned32
MODULE-COMPLIANCE OBJECT-GROUP MacAddress
SnmpAdminString PhysicalIndex CLApIfType
ciscoMgmt

Defined Objects

ciscoLwappApMIB 1.3.6.1.4.1.9.9.513
This MIB is intended to be implemented on all those devices operating as Central Controllers (CC) that terminate the Light Weight Access Point Protocol tunnel from Light-weight LWAPP Access Points. This MIB provides configuration and status information about the 802.11 Access Points that have joined the controller. The relationship between CC and the LWAPP APs can be depicted as follows: +......+ +......+ +......+ +......+ + + + + + + + + + CC + + CC + + CC + + CC + + + + + + + + + +......+ +......+ +......+ +......+ .. . . . .. . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + AP + + AP + + AP + + AP + + AP + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ . . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + MN + + MN + + MN + + MN + + MN + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard. LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller. GLOSSARY Access Point ( AP ) An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients. LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends it to the controller to which it is logically connected. Basic Service Set Identifier (BSSID) The identifier for the service set comprising of all the 802.11 stations under the control of one coordinating Access Point. This identifier happens to be the MAC address of the dot11 radio interface of the Access Point. The wireless clients that associate with the Access Point get the wired uplink through this particular dot11 interface. Central Controller ( CC ) The central entity that terminates the LWAPP protocol tunnel from the LWAPP APs. Throughout this MIB, this entity also referred to as 'controller'. Light Weight Access Point Protocol ( LWAPP ) This is a generic protocol that defines the communication between the Access Points and the Central Controller. Mobile Node ( MN ) A roaming 802.11 wireless device in a wireless network associated with an access point. Station Management (SMT) This term refers to the internal management of the 802.11 protocol operations by the AP to work cooperatively with the other APs and 802.11 devices in the network. REFERENCE [1] Part 11 Wireless LAN Medium Access Control ( MAC ) and Physical Layer ( PHY ) Specifications. [2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol.
MODULE-IDENTITY    

ciscoLwappApMIBNotifs 1.3.6.1.4.1.9.9.513.0
OBJECT IDENTIFIER    

ciscoLwappApMIBObjects 1.3.6.1.4.1.9.9.513.1
OBJECT IDENTIFIER    

ciscoLwappAp 1.3.6.1.4.1.9.9.513.1.1
OBJECT IDENTIFIER    

cLApTable 1.3.6.1.4.1.9.9.513.1.1.1
This table represents the information about the 802.11 LWAPP Access Points that have joined the controller. LWAPP APs exchange configuration messages with the controller and get the required configuration for their 802.11 related operations, after they join the controller.
OBJECT-TYPE    
  SEQUENCE OF  
    CLApEntry

cLApEntry 1.3.6.1.4.1.9.9.513.1.1.1.1
Each entry in this table provides information about one 802.11 LWAPP Access Point that has joined the controller. Entries are removed when the APs lose their association with the controller due to loss of communication.
OBJECT-TYPE    
  CLApEntry  

cLApSysMacAddress 1.3.6.1.4.1.9.9.513.1.1.1.1.1
This object represents the radio MAC address common to the dot11 interfaces of the AP and uniquely identifies an entry in this table.
OBJECT-TYPE    
  MacAddress  

cLApIfMacAddress 1.3.6.1.4.1.9.9.513.1.1.1.1.2
This object represents the Ethernet MAC address of the AP.
OBJECT-TYPE    
  MacAddress  

cLApMaxNumberOfDot11Slots 1.3.6.1.4.1.9.9.513.1.1.1.1.3
This object represents the maximum number of 802.11 radio interface slots in this AP.
OBJECT-TYPE    
  Unsigned32  

cLApEntPhysicalIndex 1.3.6.1.4.1.9.9.513.1.1.1.1.4
This object provides the index value in the entPhysicalEntry corresponding to this AP.
OBJECT-TYPE    
  PhysicalIndex  

cLApName 1.3.6.1.4.1.9.9.513.1.1.1.1.5
This object represents the administrative name assigned to the AP by the user. If an AP is not configured, its factory default name will be ap: eg. ap:af:12:be.
OBJECT-TYPE    
  SnmpAdminString SIZE(0..32)  

cLApIfSmtParamTable 1.3.6.1.4.1.9.9.513.1.1.2
This table represents the station management information in the APs that have joined the controller. Information populated through the entries of this table is used by the AP to perform the expected 802.11 operations on the respective dot11 interfaces to coordinate with other 802.11 devices in the network. Since this table has the indices defined in the tables cLApTable and cLApDot11IfTable, an entry in this table is automatically removed when the respective entry is removed in either of those tables.
OBJECT-TYPE    
  SEQUENCE OF  
    CLApIfSmtParamEntry

cLApIfSmtParamEntry 1.3.6.1.4.1.9.9.513.1.1.2.1
An entry in this table represents the information pertaining to one particular dot11 interface of this AP used to perform the 802.11 protocol operations on the respective dot11 interface. Rows are added or deleted to this table when APs join or leave the controller respectively.
OBJECT-TYPE    
  CLApIfSmtParamEntry  

cLApIfSmtDot11Bssid 1.3.6.1.4.1.9.9.513.1.1.2.1.1
This object defines the base BSSID of this AP, which is the MAC address of the radio interface of this AP.
OBJECT-TYPE    
  MacAddress  

ciscoLwappApIf 1.3.6.1.4.1.9.9.513.1.2
OBJECT IDENTIFIER    

cLApDot11IfTable 1.3.6.1.4.1.9.9.513.1.2.1
This table represents the information about the basic functional parameters corresponding to the dot11 interfaces of the APs that have joined the controller.
OBJECT-TYPE    
  SEQUENCE OF  
    CLApDot11IfEntry

cLApDot11IfEntry 1.3.6.1.4.1.9.9.513.1.2.1.1
An entry in this table represents the 802.11 functional parameters of the dot11 interface of an AP that has joined the controller. Entries are added when the APs associate to this controller and deleted when they lose their association.
OBJECT-TYPE    
  CLApDot11IfEntry  

cLApDot11IfSlotId 1.3.6.1.4.1.9.9.513.1.2.1.1.1
This object represents the slot ID of a dot11 interface on an AP. The slot ID for a particular dot11 interface as represented by this object ranges from 0 to cLApMaxNumberOfDot11Slots - 1.
OBJECT-TYPE    
  Unsigned32  

cLApDot11IfType 1.3.6.1.4.1.9.9.513.1.2.1.1.2
This object represents the type of this dot11 interface.
OBJECT-TYPE    
  CLApIfType  

ciscoLwappApMIBConform 1.3.6.1.4.1.9.9.513.2
OBJECT IDENTIFIER    

ciscoLwappApMIBCompliances 1.3.6.1.4.1.9.9.513.2.1
OBJECT IDENTIFIER    

ciscoLwappApMIBCompliance 1.3.6.1.4.1.9.9.513.2.1.1
The compliance statement for the SNMP entities that implement the ciscoLwappApMIB module.
MODULE-COMPLIANCE    

ciscoLwappApMIBComplianceRev1 1.3.6.1.4.1.9.9.513.2.1.2
The compliance statement for the SNMP entities that implement the ciscoLwappApMIB module.
MODULE-COMPLIANCE    

ciscoLwappApMIBComplianceRev2 1.3.6.1.4.1.9.9.513.2.1.3
The compliance statement for the SNMP entities that implement the ciscoLwappApMIB module.
MODULE-COMPLIANCE    

ciscoLwappApMIBGroups 1.3.6.1.4.1.9.9.513.2.2
OBJECT IDENTIFIER    

ciscoLwappApGroup 1.3.6.1.4.1.9.9.513.2.2.1
This collection of objects represents the information about the general attributes and functional parameters of those APs that have joined the controller.
OBJECT-GROUP    

ciscoLwappApIfGroup 1.3.6.1.4.1.9.9.513.2.2.2
This collection of objects represents the information about the dot11 interfaces of those APs that have joined the controller.
OBJECT-GROUP    

ciscoLwappApGroupSup1 1.3.6.1.4.1.9.9.513.2.2.3
This supplemental collection of objects represents the information about the general attributes and functional parameters of those APs that have joined the controller.
OBJECT-GROUP    

ciscoLwappApGroupSup2 1.3.6.1.4.1.9.9.513.2.2.4
This supplemental collection of objects represents the names of the APs that have joined the controller.
OBJECT-GROUP    

ciscoLwappApMIBNotifObjects 1.3.6.1.4.1.9.9.513.3
OBJECT IDENTIFIER    

Defined Objects

CLApEntry  
SEQUENCE    
  MacAddress as cLApSysMacAddress  
  MacAddress as cLApIfMacAddress  
  Unsigned32 as cLApMaxNumberOfDot11Slots  
  PhysicalIndex as cLApEntPhysicalIndex  
  SnmpAdminString as cLApName  

CLApDot11IfEntry  
SEQUENCE    
  Unsigned32 as cLApDot11IfSlotId  
  CLApIfType as cLApDot11IfType  

CLApIfSmtParamEntry  
SEQUENCE    
  MacAddress as cLApIfSmtDot11Bssid