CISCO-LWAPP-LOCAL-AUTH-MIB

File: CISCO-LWAPP-LOCAL-AUTH-MIB.mib (20939 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
CISCO-SMI CISCO-LWAPP-WLAN-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Unsigned32
Integer32 MODULE-COMPLIANCE OBJECT-GROUP
DisplayString RowStatus TruthValue
ciscoMgmt cLWlanIndex

Defined Objects

ciscoLwappLocalAuthMIB 1.3.6.1.4.1.9.9.619
This MIB is intended to be implemented on all those devices operating as Central controllers, that terminate the Light Weight Access Point Protocol tunnel from Cisco Light-weight LWAPP Access Points. Information provided by this MIB is used to manage Local authentication information on the controller. The relationship between CC and the LWAPP APs can be depicted as follows: +......+ +......+ +......+ + + + + + + + CC + + CC + + CC + + + + + + + +......+ +......+ +......+ .. . . .. . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ + + + + + + + + + AP + + AP + + AP + + AP + + + + + + + + + +......+ +......+ +......+ +......+ . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ + + + + + + + + + MN + + MN + + MN + + MN + + + + + + + + + +......+ +......+ +......+ +......+ The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard. LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller. GLOSSARY Access Point ( AP ) An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients. LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends them to the controller to which it is logically connected. Gratuitous Probe Response (GPR) The Gratuitous Probe Response feature aids in conserving battery power of WLAN-enabled cell phones by providing a high rate packet on the order of tens of milliseconds such that these kind of phones can wake up and wait at predefined intervals, to reduce battery power. The GPR packet is transmitted from the AP at a predefined time interval. Light Weight Access Point Protocol ( LWAPP ) This is a generic protocol that defines the communication between the Access Points and the Central Controller. Mobile Node ( MN ) A roaming 802.11 wireless device in a wireless network associated with an access point. Mobile Node and client are used interchangeably. Extensible Authentication Protocol ( EAP ) EAP is a universal authentication protocol used in wireless and PPP networks. It is defined by RFC 3748. EAP-Flexible Authentication ( EAP-FAST ) This protocol is used via secure tunneling for 802.1X EAP. Transport Layer Security ( TLS ) This is a cryptographic protocol which provides secure communication over the network. Lightweight Directory Access Protocol ( LDAP ) LDAP is a protocol used for obtaining directory services and runs over TCP/IP. REFERENCE [1] Wireless LAN Medium Access Control ( MAC ) and Physical Layer ( PHY ) Specifications [2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol
MODULE-IDENTITY    

ciscoLwappLocalAuthMIBNotifs 1.3.6.1.4.1.9.9.619.0
OBJECT IDENTIFIER    

ciscoLwappLocalAuthMIBObjects 1.3.6.1.4.1.9.9.619.1
OBJECT IDENTIFIER    

cllaConfig 1.3.6.1.4.1.9.9.619.1.1
OBJECT IDENTIFIER    

cllaLocalAuth 1.3.6.1.4.1.9.9.619.1.1.1
OBJECT IDENTIFIER    

cllaActiveTimeout 1.3.6.1.4.1.9.9.619.1.1.1.1
The timeout period for the Local EAP to remain active, in seconds.
OBJECT-TYPE    
  Unsigned32 1..3600  

cllaEapProfileTable 1.3.6.1.4.1.9.9.619.1.1.2
This table represents the local EAP authentication information on the controller. Rows are added or deleted by explicit management actions initiated by the user from a network management station through the cllaEapProfileRowStatus object.
OBJECT-TYPE    
  SEQUENCE OF  
    CllaEapProfileEntry

cllaEapProfileEntry 1.3.6.1.4.1.9.9.619.1.1.2.1
A conceptual row in cllaEapProfileTable. Each entry in this table represents the local EAP authentication information, identified by the cllEapProfileName.
OBJECT-TYPE    
  CllaEapProfileEntry  

cllaEapProfileName 1.3.6.1.4.1.9.9.619.1.1.2.1.1
This object represent the profile name used to identify the Local EAP information.
OBJECT-TYPE    
  DisplayString SIZE(0..63)  

cllaEapProfileMethods 1.3.6.1.4.1.9.9.619.1.1.2.1.2
This object represents the method type for this entry. none - No method is in use leap - LEAP is used as one of the methods eap-fast - EAP-FAST is used as one of the methods tls - TLS is being used as one of the methods.
OBJECT-TYPE    
  BITS none(0), leap(1), eapFast(2), tls(3)  

cllaEapProfileCertIssuer 1.3.6.1.4.1.9.9.619.1.1.2.1.3
This object represents the name of the certificate issuer cisco - Cisco is the certificate issuer. vendor - The issuer is an outside vendor.
OBJECT-TYPE    
  INTEGER cisco(1), vendor(2)  

cllaEapProfileCaCertificationCheck 1.3.6.1.4.1.9.9.619.1.1.2.1.4
This parameter indicates whether to check peer certificate against installed CA certificates.
OBJECT-TYPE    
  TruthValue  

cllaEapProfileCnCertificationIdVerify 1.3.6.1.4.1.9.9.619.1.1.2.1.5
This parameter indicates whether to verify certificate CN against peer identity and user database.
OBJECT-TYPE    
  TruthValue  

cllaEapProfileDateValidityEnabled 1.3.6.1.4.1.9.9.619.1.1.2.1.6
This parameter indicates whether to verify certificate date is valid and is within validity period.
OBJECT-TYPE    
  TruthValue  

cllaEapProfileLocalCertificateRequired 1.3.6.1.4.1.9.9.619.1.1.2.1.7
This is applicable when cllaEapProfileMethods is EAP-FAST parameter. This parameter indicates whether local certificate is required.
OBJECT-TYPE    
  TruthValue  

cllaEapProfileClientCertificateRequired 1.3.6.1.4.1.9.9.619.1.1.2.1.8
This is applicable when cllaEapProfileMethods is EAP-FAST parameter. This parameter indicates whether client certificate is required.
OBJECT-TYPE    
  TruthValue  

cllaEapProfileRowStatus 1.3.6.1.4.1.9.9.619.1.1.2.1.9
Used to add or delete an entry in this table.
OBJECT-TYPE    
  RowStatus  

cllaWlanProfileTable 1.3.6.1.4.1.9.9.619.1.1.3
This table represents the information about configuring the EAP profiles for a WLAN. The creation of a new row occurs when a WLAN entry is added through an explicit network management action to the cLWlanConfigTable in CISCO-LWAPP-WLAN-MIB. Similarly, deletion of a row in cLWlanConfigTable through user action, causes the deletion of corresponding row in this table.
OBJECT-TYPE    
  SEQUENCE OF  
    CllaWlanProfileEntry

cllaWlanProfileEntry 1.3.6.1.4.1.9.9.619.1.1.3.1
Each entry in this table provides information about the Local EAP profile configured for this WLAN.
OBJECT-TYPE    
  CllaWlanProfileEntry  

cllaWlanProfileName 1.3.6.1.4.1.9.9.619.1.1.3.1.1
The profile name configured for this WLAN.
OBJECT-TYPE    
  DisplayString SIZE(0..63)  

cllaWlanProfileState 1.3.6.1.4.1.9.9.619.1.1.3.1.2
This object indicates whether Local Authentication is enabled or disables for this WLAN.
OBJECT-TYPE    
  TruthValue  

cllaUserPriorityTable 1.3.6.1.4.1.9.9.619.1.1.4
This table contains entries for 802.11 user credential methods configured in the controller. At startup, all the entries in this table are set up by the central controller. A management application can later change the priority order using the cllaUserPriorityNumber.
OBJECT-TYPE    
  SEQUENCE OF  
    CllaUserPriorityEntry

cllaUserPriorityEntry 1.3.6.1.4.1.9.9.619.1.1.4.1
A conceptual row in cllaUserPriorityTable. There is an entry in this table for each 802.11 user authentication available at the agent, as identified by a value of cllaUserCredential.
OBJECT-TYPE    
  CllaUserPriorityEntry  

cllaUserCredential 1.3.6.1.4.1.9.9.619.1.1.4.1.1
This object represents the user crediantial information. local - indicates that local credential is used for authentication ldap - indicates that LDAP credential is used for authentication.
OBJECT-TYPE    
  INTEGER local(1), ldap(2)  

cllaUserPriorityNumber 1.3.6.1.4.1.9.9.619.1.1.4.1.2
This object represents the order in which the user credentials are validated by the controller. At start up, the agent assigns the value of this object. Later this can be changed by the management station. This object reflects the priority in which the user credential information is applied. A lower value indicates an higher priority. For example, an entry set to value '1' has a higher priority over an entry set to value '2'. The zero value indicates that the priority is not set. No two instances of this object will have the same priority.
OBJECT-TYPE    
  Integer32 0..2  

cllaEapParams 1.3.6.1.4.1.9.9.619.1.1.5
OBJECT IDENTIFIER    

cllaEapMethodPacTtl 1.3.6.1.4.1.9.9.619.1.1.5.1
This is EAP Fast parameter. This parameter represents time to live for the protected access credentials.
OBJECT-TYPE    
  Unsigned32 1..1000  

cllaEapAnonymousProvEnabled 1.3.6.1.4.1.9.9.619.1.1.5.2
This is EAP Fast parameter. This parameter represents whether anonymous provisioning is enabled. A value of 'true' indicates the controller will accept anonymous requests. A value of 'false' indicates that the controller will reject anonymous requests.
OBJECT-TYPE    
  TruthValue  

cllaEapAuthorityId 1.3.6.1.4.1.9.9.619.1.1.5.3
This is EAP Fast parameter. This parameter configures the authority ID. The maximum length per platform is specified by the cllaEapAuthorityIdLength object.
OBJECT-TYPE    
  OCTET STRING SIZE(0..128)  

cllaEapAuthorityInfo 1.3.6.1.4.1.9.9.619.1.1.5.4
This is EAP Fast parameter. This parameter configures the authority information.
OBJECT-TYPE    
  OCTET STRING SIZE(0..32)  

cllaEapServerKey 1.3.6.1.4.1.9.9.619.1.1.5.5
This is EAP Fast parameter. This parameter configures the server key ID.
OBJECT-TYPE    
  OCTET STRING SIZE(1..32)  

cllaEapAuthorityIdLength 1.3.6.1.4.1.9.9.619.1.1.5.6
This object represents the length of the cllaEapAuthorityId object, supported by this agent implementation.
OBJECT-TYPE    
  Unsigned32 0..128  

ciscoLwappLocalAuthMIBConform 1.3.6.1.4.1.9.9.619.2
OBJECT IDENTIFIER    

ciscoLwappLocalAuthMIBCompliances 1.3.6.1.4.1.9.9.619.2.1
OBJECT IDENTIFIER    

ciscoLwappLocalAuthMIBCompliance 1.3.6.1.4.1.9.9.619.2.1.1
The compliance statement for the SNMP entities that implement the ciscoLwappLocalAuthMIB module.
MODULE-COMPLIANCE    

ciscoLwappLocalAuthMIBGroups 1.3.6.1.4.1.9.9.619.2.2
OBJECT IDENTIFIER    

ciscoLwappLocalAuthMIBConfigGroup 1.3.6.1.4.1.9.9.619.2.2.1
This collection of objects specifies the required configuration parameters for local authentication.
OBJECT-GROUP    

Defined Objects

CllaEapProfileEntry  
SEQUENCE    
  DisplayString as cllaEapProfileName  
  BITS as cllaEapProfileMethods  
  INTEGER as cllaEapProfileCertIssuer  
  TruthValue as cllaEapProfileCaCertificationCheck  
  TruthValue as cllaEapProfileCnCertificationIdVerify  
  TruthValue as cllaEapProfileDateValidityEnabled  
  TruthValue as cllaEapProfileLocalCertificateRequired  
  TruthValue as cllaEapProfileClientCertificateRequired  
  RowStatus as cllaEapProfileRowStatus  

CllaWlanProfileEntry  
SEQUENCE    
  DisplayString as cllaWlanProfileName  
  TruthValue as cllaWlanProfileState  

CllaUserPriorityEntry  
SEQUENCE    
  INTEGER as cllaUserCredential  
  Integer32 as cllaUserPriorityNumber