
CISCO-MGX82XX-PXM-CLOCK-MIB
File:
CISCO-MGX82XX-PXM-CLOCK-MIB.mib (13493 bytes)
Imported modules
Imported symbols
Defined Objects
| pxmCurrentClock |
1.3.6.1.4.1.351.110.3.16.7 |
| This object represents the clock source currently selected for PXM card. primary(1): The primary clock source is described by pxmPrimaryMuxClockSource secondary(2): The secondary clock source is described by pxmSecondaryMuxClockSource. intOscillator(3): Current clock is internal oscillator. |
| OBJECT-TYPE |
|
|
|
| |
CmpCurrentClock |
|
|
| pxmClkStratumLevel |
1.3.6.1.4.1.351.110.3.16.12 |
| This object describes the lowest stratum level provided by the interface the external clock source to the PXM back card. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
stratumUnknown(1), stratumLevel1(2), stratumLevel2(3), stratumLevel3E(4), stratumLevel3(5), stratumLevel4(6), stratumLevel4E(7) |
|
| pxmClkErrReason |
1.3.6.1.4.1.351.110.3.16.13 |
| This object gives more information about clock status. The possible values are : goodClk(1) : Clock is good unkownReason(2) : reason not known noClkSignal(3) : Loss of signal(LOS) on clock source freqTooHigh(4) : frequency drifted too high freqTooLow(5) : frequency drifted too low excessiveJitter(6) : jitter has exceeded the tolerance missingCard (7) : no clock hardware found missingLogicalIf(8): Logical Interface missing or not operational noClock (9): No clock. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
goodClk(1), unknownReason(2), noClkSignal(3), freqTooHigh(4), freqTooLow(5), excessiveJitter(6), missingCard(7), missingLogicalIf(8), noClock(9) |
|
| ciscoMgx82xxPxmClockMIB |
1.3.6.1.4.1.351.150.72 |
| The MIB module to describe the clock configuration in Processor Switch Module(PXM) in MGX82xx product. Back cards supported for PXM1: PXM-UI : T1 Clock port, E1 Clock Port PXM-UI-S3 : External Clock1 for T1/E1 Clock input. |
| MODULE-IDENTITY |
|
|
|
| cmpClockInfoGroup |
1.3.6.1.4.1.351.150.72.2.1.1 |
| The collection of objects which are used for providing information on PXM Clock configuration. |
| OBJECT-GROUP |
|
|
|
| cmpExtClockInfoGroup |
1.3.6.1.4.1.351.150.72.2.1.4 |
| The collection of objects which are used for providing general information on PXM Clock configuration. |
| OBJECT-GROUP |
|
|
|
Defined Objects
| CmpClockConnectorType |
|
| Represents the connector type for the clock device. rj45Type(1): RJ-45 Connector. This is for T1/E1 clock input. smbType (2): SMB Connector. This is for E1 clock input. |
| TEXTUAL-CONVENTION |
|
|
|
| |
INTEGER |
rj45Type(1), smbType(2) |
|
| CmpClockSourceType |
|
| This object identifies the source of the Mux Clock on PXM card. pxmInbandClock1 (1), pxmInbandClock2 (5): clock is derived from physical line pxmServiceModuleClock1(2), pxmServiceModuleClock2(6): clock is derived from service module. pxmTopSRMClock (3), pxmBottomSRMClock (7): clock is derived from SRM module. pxmExternalClock(4), pxmExternalClock2(9) :clock is derived from the port. pxmInternalOscillator (8): clock is derived from internal oscillator. |
| TEXTUAL-CONVENTION |
|
|
|
| |
INTEGER |
pxmInbandClock1(1), pxmServiceModuleClock1(2), pxmTopSRMClock(3), pxmExternalClock(4), pxmInbandClock2(5), pxmServiceModuleClock2(6), pxmBottomSRMClock(7), pxmInternalOscillator(8), pxmExternalClock2(9) |
|
| CmpCurrentClock |
|
| This TEXTUAL Convention represents the clock source currently selected for PXM card. primary(1): The primary clock source is described by pxmPrimaryMuxClockSource secondary(2): The secondary clock source is described by pxmSecondaryMuxClockSource. intOscillator(3): Current clock is internal oscillator. |
| TEXTUAL-CONVENTION |
|
|
|
| |
INTEGER |
primary(1), secondary(2), intOscillator(3) |
|
| CmpClockExistence |
|
| This TEXTUAL Convention represents the existence of the clock source. clkNotPresent (1): The T1/E1 external clock not present. clkPresent (2): The T1/E1 external clock present. |
| TEXTUAL-CONVENTION |
|
|
|
| |
INTEGER |
clkNotPresent(1), clkPresent(2) |
|