CISCO-OTN-IF-MIB

File: CISCO-OTN-IF-MIB.mib (79946 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
IF-MIB CISCO-SMI

Imported symbols

Integer32 Counter32 Unsigned32
Counter64 MODULE-IDENTITY OBJECT-TYPE
MODULE-COMPLIANCE OBJECT-GROUP TEXTUAL-CONVENTION
TruthValue RowStatus StorageType
ifIndex ciscoMgmt

Defined Objects

ciscoOtnIfMIB 1.3.6.1.4.1.9.9.639
This MIB module defines the managed objects for physical layer characteristics of DWDM optical channel interfaces and performance statistics objects for protocol specific error counters in DWDM optical devices. Performance monitoring (PM) parameters are used by service providers to gather, store, set thresholds for and report performance data for early detection of problems. Thresholds are used to set error levels for each PM parameter. During the accumulation cycle, if the current value of a performance monitoring parameter reaches or exceeds its corresponding threshold value, a threshold crossing alarm (TCA) is generated. The TCAs provide early detection of performance degradation. The definitions contained herein are based on the OTN specifications in ITU-T G.872[ITU-T G.872], G.709 [ITU-T G.709], G.798[ITU-T G.798], G.874[ITU-T G.874], and G.874.1[ITU-T G.874.1]. Glossary: OTN : Optical Transport Network (ITU-T G.709). FEC : Forward Error Correction. PM : Performance Monitor. DWDM : Dense Wavelength Division Multiplexing. FE : Farend or client side of the interface. NE : Nearend or trunk side of the interface. ADM : Add Drop Multiplexer. OCH : Optical Channel. OTS : Optical Transport Section. OMS : Optical Multiplex Section. TCA : Threshold Crossing Alarm. OSC : Optical Supervisory Channel. DCU : Dispersion Compensation Unit. EXP : Express Channel. OSNR : Optical singal to noise ratio.
MODULE-IDENTITY    

ciscoOtnIfMIBNotifs 1.3.6.1.4.1.9.9.639.0
OBJECT IDENTIFIER    

ciscoOtnIfMIBObjects 1.3.6.1.4.1.9.9.639.1
OBJECT IDENTIFIER    

coiDwdmInterface 1.3.6.1.4.1.9.9.639.1.1
OBJECT IDENTIFIER    

coiIfControllerTable 1.3.6.1.4.1.9.9.639.1.1.1
This table provides management information for physical layer related attributes of interfaces with an ifType of opticalChannel(195).
OBJECT-TYPE    
  SEQUENCE OF  
    CoiIfControllerEntry

coiIfControllerEntry 1.3.6.1.4.1.9.9.639.1.1.1.1
An entry containing management information on physical layer related attributes of interfaces with an ifType opticalChannel(195). Entries are created by the agent when a new interface is added to the ifTable. Entries are deleted by the agent when an interface is removed from the ifTable.
OBJECT-TYPE    
  CoiIfControllerEntry  

coiIfControllerLoopback 1.3.6.1.4.1.9.9.639.1.1.1.1.1
This object is used to configure the loopback mode of the interface. valid values are - 'noLoop' - No Loopback present. 'otherLoop' - A loopback of type other than rest of types defined in this enumeration. 'diagnosticLoop' - This is an internal loopback, where the data stream is looped from the transmit to receive section. It is used for hardware debug, bring-up and diagnostics. 'lineLoop' - In this mode, the receive data stream is looped back to the transmit side.
OBJECT-TYPE    
  INTEGER noLoop(1), otherLoop(2), diagnosticLoop(3), lineLoop(4)  

coiIfControllerWavelength 1.3.6.1.4.1.9.9.639.1.1.1.1.2
This object is used to configure the wavelength of operation on applicable optical channel interfaces.
OBJECT-TYPE    
  CoiOpticalWavelength  

coiIfControllerLaserAdminStatus 1.3.6.1.4.1.9.9.639.1.1.1.1.3
This object is used to configure laser status on applicable interfaces. when it is set to down(2), it results in traffic drop and there should be corresponding change in coiIfControllerLaserOperStatus. Valid values are - 'up' - Turn on the Laser 'down' - shutdown the Laser.
OBJECT-TYPE    
  INTEGER up(1), down(2)  

coiIfControllerLaserOperStatus 1.3.6.1.4.1.9.9.639.1.1.1.1.4
This object gives the current operational state of the Laser. Valid values are - 'up' - The laser is operational. 'down' - The laser is not operational. if coiIfControllerLaserAdminStatus is down(2) then coiIfControllerLaserOperStatus should be down(2). If coiIfControllerLaserAdminStatus is changed to up(1) then coiIfControllerLaserOperStatus should change to up(1), provided the laser is operational and ready to transmit traffic. It should remain in down(2) if there is a fault that prevents it from going to the up(1) state.
OBJECT-TYPE    
  INTEGER up(1), down(2)  

coiIfControllerOtnStatus 1.3.6.1.4.1.9.9.639.1.1.1.1.5
This object allows the management client to enable the OTN (ITU-T G.709) framing on applicable interfaces of ifType opticalChannel(195). Valid values are - 'true' - Enables OTN (ITU-T g.709) framing on the interface. 'false' - Disables OTN (ITU-T g.709 framing on the interface. Setting a value of 'false' to coiIfControllerOtnStatus would result in loss of traffic.
OBJECT-TYPE    
  TruthValue  

coiIfControllerFECMode 1.3.6.1.4.1.9.9.639.1.1.1.1.6
This object allows the management client to enable FEC ( Forward Error Correction ) on applicable interfaces. FEC is a technique that improves digital channel quality through the addition of redundant data at the sending node. This redundant data is decoded at the receiver to detect and correct errors. Valid values are 'disable' - disables FEC on the interface. 'enableStandard' - enables standard FEC on the interface (ITU-T G.975). 'enableEnhanced' - enables proprietary FEC on the interface.
OBJECT-TYPE    
  INTEGER disable(1), enableStandard(2), enableEnhanced(3)  

coiIfControllerTDCOperMode 1.3.6.1.4.1.9.9.639.1.1.1.1.7
This object gives the operational mode of the Tuned Dispersion Compensator (TDC). The values may be - 'auto' - Automatic tuning of dispersion compensation. 'manual' - Manual tuning of dispersion compensation.
OBJECT-TYPE    
  INTEGER auto(1), manual(2)  

coiIfControllerTDCOperStatus 1.3.6.1.4.1.9.9.639.1.1.1.1.8
This object gives the operational status of the Tuned Dispersion Compensator (TDC). The values may be - 'disabled' - TDC has been disabled. 'acquiring' - TDC is acquiring or tuning to the desired compensation setting. 'locked' - TDC has been tuned and locked at the desired compensation setting
OBJECT-TYPE    
  INTEGER disabled(1), acquiring(2), locked(3)  

coiIfControllerTDCOperSetting 1.3.6.1.4.1.9.9.639.1.1.1.1.9
This object gives the dispersion compensation setting that the TDC has been tuned to. It is expressed in pico-seconds per nanometer. Example: The value of -650 represents a dispersion compensation setting of -650 ps/nm.
OBJECT-TYPE    
  Integer32 -2000..2000  

coiIfControllerPreFECBERMantissa 1.3.6.1.4.1.9.9.639.1.1.1.1.10
This object gives the mantissa part of the Pre FEC BER or correctable BER at any instance of time. It is represented in one hundreths of a unit.The exponent part is defined in coiIfControllerPreFECBERExponent Pre FEC BER is the BER of the signal before it undergoes the FEC algorithm. FEC will correct errors upto a certain Pre FEC BER beyond which the signal starts becoming uncorrectable. Knowing the Pre FEC BER helps monitor system health. Pre FEC BER is expressed in Scientific E notation with two decimal places Example: The value 235 represents the mantissa of 2.35
OBJECT-TYPE    
  Integer32 0..999  

coiIfControllerPreFECBERExponent 1.3.6.1.4.1.9.9.639.1.1.1.1.11
This object gives the exponent part of the Pre FEC BER or correctable BER at any instance of time. It is represented in powers of 10. The mantissa part is defined in coiIfControllerPreFECBERMantissa. Pre FEC BER is the BER of the signal before it undergoes the FEC algorithm. FEC will correct errors upto a certain Pre FEC BER beyond which the signal starts becoming uncorrectable. Knowing the Pre FEC BER helps monitor system health. Pre FEC BER is expressed in Scientific E notation with two decimal places Example: The value -11 represents the exponent value of 10 to the power of -11.
OBJECT-TYPE    
  Integer32 -30..0  

coiIfControllerQFactor 1.3.6.1.4.1.9.9.639.1.1.1.1.12
This Object gives the value of Q-Factor represented in one hundredths of a dB. Q-Factor represents the analog signal to noise ratio. It suggests the minimum correctable BER for a given signal. The higher the Q-factor, the better. Q-factor is expressed in dB Example: The value 365 represents a Q-Factor of 3.65 dB
OBJECT-TYPE    
  Integer32 0..9999  

coiIfControllerQMargin 1.3.6.1.4.1.9.9.639.1.1.1.1.13
Q-Margin defines how much operational system margin that is available for a given circuit. Minimum margin should be defined by one's Network Engineering Group. Q-margin is expressed in dBQ. dBQ is a scale relative to min required Q-Factor given by coiIfControllerQFactor. This object gives the value of the Q-Margin represented in one hundredths of a dBQ. Example: The value 236 represents a Q-Margin of 2.36 dBQ.
OBJECT-TYPE    
  Integer32 0..9999  

coiIfControllerOTNValidIntervals 1.3.6.1.4.1.9.9.639.1.1.1.1.14
This object gives the number of contiguous 15 minute intervals for which valid OTN performance monitoring data is available for the particular interface. The actual performance data is available in the following Tables coiOtnNearEndIntervalTable coiOtnFarEndIntervalTable The value of this object will be n (where n is the maximum number of 15 minute intervals supported at this interface), unless the measurement was (re-)started within the last (nx15) minutes, in which case the value will be the number of 15 minute intervals for which the agent has some data. This object reports value zero, if OTN is turned off by setting coiIfControllerOtnStatus to 'false'.
OBJECT-TYPE    
  Unsigned32 0..96  

coiIfControllerFECValidIntervals 1.3.6.1.4.1.9.9.639.1.1.1.1.15
This object gives the number of contiguous 15 minute intervals for which valid FEC PM data is available for the particular interface. The actual performance data is available in the following Table coiFECIntervalTable The value of this object will be n (where n is the maximum number of 15 minute intervals supported at this interface), unless the measurement was (re-)started within the last (nx15) minutes, in which case the value will be the number of 15 minute intervals for which the agent has some data. This object reports a value 0, if FEC is disabled by setting coiIfControllerFECMode to 'disable'.
OBJECT-TYPE    
  Unsigned32 0..96  

coiDwdmIfOtn 1.3.6.1.4.1.9.9.639.1.2
OBJECT IDENTIFIER    

coiOtnNearEndThresholdsTable 1.3.6.1.4.1.9.9.639.1.2.1
This table provides objects for configuring OTN ( G.709 ) near end error thresholds on interfaces of ifType opticalChannel (195).
OBJECT-TYPE    
  SEQUENCE OF  
    CoiOtnNearEndThresholdsEntry

coiOtnNearEndThresholdsEntry 1.3.6.1.4.1.9.9.639.1.2.1.1
An entry containing management information for configuration of performance monitoring thresholds for a given monitor and threshold type. Entries can be created for interfaces with ifType of opticalChannel(195). Thresholds are created/destroyed through the entry's RowStatus object semantics. The coiOtnNearEndThreshIntervalType defines the time interval over which the data being monitored is accumulated for which the threshold is to be applied. The coiOtnNearEndThreshMonType defines the type of statistics to which the threshold applies. The coiOtnNearEndThresholdType defines the specific threshold type value, which the threshold refers to.
OBJECT-TYPE    
  CoiOtnNearEndThresholdsEntry  

coiOtnNearEndThreshIntervalType 1.3.6.1.4.1.9.9.639.1.2.1.1.1
This object specifies the interval type during which the performance statistics were accumulated.
OBJECT-TYPE    
  CoiIntervalType  

coiOtnNearEndThreshMonType 1.3.6.1.4.1.9.9.639.1.2.1.1.2
This object gives the type of performance monitoring for which the threshold is being set.
OBJECT-TYPE    
  CoiMonitorType  

coiOtnNearEndThresholdType 1.3.6.1.4.1.9.9.639.1.2.1.1.3
This object gives the type of Error Threshold that is being set.
OBJECT-TYPE    
  CoiOtnThresholdType  

coiOtnNearEndThreshValue 1.3.6.1.4.1.9.9.639.1.2.1.1.4
This object is used to set the near end threshold value for the given threshold type as identified by coiOtnNearEndThresholdType.
OBJECT-TYPE    
  Unsigned32  

coiOtnNearEndThreshStorageType 1.3.6.1.4.1.9.9.639.1.2.1.1.5
The storage type for this conceptual row.
OBJECT-TYPE    
  StorageType  

coiOtnNearEndThreshStatus 1.3.6.1.4.1.9.9.639.1.2.1.1.6
This object controls the creation and deletion of a conceptual row in this table. The value of this object has no effect on whether other objects in this conceptual row can be modified. A conceptual row can not be made active until the coiOtnNearEndThreshValue has been set to a valid threshold value.
OBJECT-TYPE    
  RowStatus  

coiOtnFarEndThresholdsTable 1.3.6.1.4.1.9.9.639.1.2.2
This table provides objects for configuring OTN ( G.709 ) thresholds for far end of interfaces of ifType opticalChannel(195).
OBJECT-TYPE    
  SEQUENCE OF  
    CoiOtnFarEndThresholdsEntry

coiOtnFarEndThresholdsEntry 1.3.6.1.4.1.9.9.639.1.2.2.1
An entry containing managment information for configuration of far end performance monitoring thresholds for a given monitor and threshold type. Entries can be created for interfaces with ifType of opticalChannel(195). Thresholds are created/destroyed through the entry's RowStatus object semantics. The coiOtnFarEndThreshIntervalType defines the time interval over which the data being monitored is accumulated for which the threshold is to be applied. The coiOtnFarEndThreshMonType defines the type of statistics to which the threshold applies. The coiOtnFarEndThresholdType defines the specific threshold type value, which the threshold refers to.
OBJECT-TYPE    
  CoiOtnFarEndThresholdsEntry  

coiOtnFarEndThreshIntervalType 1.3.6.1.4.1.9.9.639.1.2.2.1.1
This object gives the interval type during which the performance statistics were accumulated in the far end of the interface.
OBJECT-TYPE    
  CoiIntervalType  

coiOtnFarEndThreshMonType 1.3.6.1.4.1.9.9.639.1.2.2.1.2
This object gives specify the type of monitoring for which threshold is being set on interfaces in the far end of the interface .
OBJECT-TYPE    
  CoiMonitorType  

coiOtnFarEndThresholdType 1.3.6.1.4.1.9.9.639.1.2.2.1.3
This object gives the type of Error Threshold that is being set on far end interfaces of ifType opticalChannel (195).
OBJECT-TYPE    
  CoiOtnThresholdType  

coiOtnFarEndThreshValue 1.3.6.1.4.1.9.9.639.1.2.2.1.4
This object is used to set the far end threshold value for the given threshold type as identified by the index coiOtnFarEndThresholdType.
OBJECT-TYPE    
  Unsigned32  

coiOtnFarEndThreshStorageType 1.3.6.1.4.1.9.9.639.1.2.2.1.5
The storage type for this conceptual row.
OBJECT-TYPE    
  StorageType  

coiOtnFarEndThreshStatus 1.3.6.1.4.1.9.9.639.1.2.2.1.6
This object controls the creation and deletion of a conceptual row in this table. The value of this object has no effect on whether other objects in this conceptual row can be modified. A conceptual row can not be made active until the coiOtnFarEndThreshValue has been set to valid threshold value.
OBJECT-TYPE    
  RowStatus  

coiOtnNearEndCurrentTable 1.3.6.1.4.1.9.9.639.1.2.3
This table contains the cumulative OTN (G.709) PM statistics for the near end of interfaces of ifType opticalChannel(195). The statistics are for the current interval of interval type identified by coiOtnNearEndCurIntervalType. The current PM statistics is the accumlated statistics for the time period defined by the interval type.
OBJECT-TYPE    
  SEQUENCE OF  
    CoiOtnNearEndCurrentEntry

coiOtnNearEndCurrentEntry 1.3.6.1.4.1.9.9.639.1.2.3.1
An entry containing management information on near end error/statistics counters such as Failure Counts, Errored Seconds...etc in the current interval
OBJECT-TYPE    
  CoiOtnNearEndCurrentEntry  

coiOtnNearEndCurIntervalType 1.3.6.1.4.1.9.9.639.1.2.3.1.1
This object gives the interval type during which the near end performance statistics are accumulated.
OBJECT-TYPE    
  CoiIntervalType  

coiOtnNearEndCurrentMonType 1.3.6.1.4.1.9.9.639.1.2.3.1.2
This object gives the part of optical network for which the near end OTN performance statistics are being monitored.
OBJECT-TYPE    
  CoiMonitorType  

coiOtnNearEndCurrentFCs 1.3.6.1.4.1.9.9.639.1.2.3.1.3
The counter associated with the number of failures encountered on the near end of interface in the current interval of type coiOtnNearEndCurIntervalType.
OBJECT-TYPE    
  Counter32  

coiOtnNearEndCurrentESs 1.3.6.1.4.1.9.9.639.1.2.3.1.4
The counter associated with the number of Errored Seconds encountered on near end of interface in the current interval of type coiOtnNearEndCurIntervalType.
OBJECT-TYPE    
  Counter32  

coiOtnNearEndCurrentSESs 1.3.6.1.4.1.9.9.639.1.2.3.1.5
The counter associated with the number of Severely Errored Seconds encountered on the near end of interface in the current interval of type coiOtnNearEndCurIntervalType.
OBJECT-TYPE    
  Counter32  

coiOtnNearEndCurrentUASs 1.3.6.1.4.1.9.9.639.1.2.3.1.6
The counter associated with the number of Unavailable Seconds encountered on the near end of interface in the current interval of type coiOtnNearEndCurIntervalType.
OBJECT-TYPE    
  Counter32  

coiOtnNearEndCurrentBBEs 1.3.6.1.4.1.9.9.639.1.2.3.1.7
The counter associated with the number of Background Block Errors encountered on the near end of interface in the current interval of type coiOtnNearEndCurIntervalType.
OBJECT-TYPE    
  Counter32  

coiOtnNearEndCurrentESRs 1.3.6.1.4.1.9.9.639.1.2.3.1.8
The counter associated with the Errored Seconds Ratio on the near end of interface in the current interval of type coiOtnNearEndCurIntervalType.
OBJECT-TYPE    
  Counter32  

coiOtnNearEndCurrentSESRs 1.3.6.1.4.1.9.9.639.1.2.3.1.9
The counter associated with the Severely Errored Seconds ratio on the near end of interface in current interval of type coiOtnNearEndCurIntervalType.
OBJECT-TYPE    
  Counter32  

coiOtnNearEndCurrentBBERs 1.3.6.1.4.1.9.9.639.1.2.3.1.10
The counter associated with the Background Block Errors ratio on the near end of interface in current interval of type coiOtnNearEndCurIntervalType.
OBJECT-TYPE    
  Counter32  

coiOtnFarEndCurrentTable 1.3.6.1.4.1.9.9.639.1.2.4
This table contains the cumulative OTN (G.709) PM stats for the far end of interfaces of ifType opticalChannel(195). The statistics are for the current interval of interval type identified by coiOtnFarEndCurIntervalType. The current PM statistics is the accumlated statistics for the time period defined by the interval type.
OBJECT-TYPE    
  SEQUENCE OF  
    CoiOtnFarEndCurrentEntry

coiOtnFarEndCurrentEntry 1.3.6.1.4.1.9.9.639.1.2.4.1
An entry containing managment information on far end error/statistics counters such as Failure Counts, Errored Seconds...etc in the current interval
OBJECT-TYPE    
  CoiOtnFarEndCurrentEntry  

coiOtnFarEndCurIntervalType 1.3.6.1.4.1.9.9.639.1.2.4.1.1
This object gives the interval type during which the performance statistics are accumulated in the far end of the interface.
OBJECT-TYPE    
  CoiIntervalType  

coiOtnFarEndCurrentMonType 1.3.6.1.4.1.9.9.639.1.2.4.1.2
This object gives the part of optical network for which far end OTN performance statistics are being monitored.
OBJECT-TYPE    
  CoiMonitorType  

coiOtnFarEndCurrentFCs 1.3.6.1.4.1.9.9.639.1.2.4.1.3
The counter associated with the number of failures encountered on far end of interface in current interval of type coiOtnFarEndCurIntervalType.
OBJECT-TYPE    
  Counter32  

coiOtnFarEndCurrentESs 1.3.6.1.4.1.9.9.639.1.2.4.1.4
The counter associated with the number of Errored Seconds encountered on far end of interface in current interval of type coiOtnFarEndCurIntervalType.
OBJECT-TYPE    
  Counter32  

coiOtnFarEndCurrentSESs 1.3.6.1.4.1.9.9.639.1.2.4.1.5
The counter associated with the number of Severely Errored Seconds encountered on far end of interface in the current interval of type coiOtnFarEndCurIntervalType.
OBJECT-TYPE    
  Counter32  

coiOtnFarEndCurrentUASs 1.3.6.1.4.1.9.9.639.1.2.4.1.6
The counter associated with the number of Unavailable Seconds encountered on far end of interface in the current interval of type coiOtnFarEndCurIntervalType.
OBJECT-TYPE    
  Counter32  

coiOtnFarEndCurrentBBEs 1.3.6.1.4.1.9.9.639.1.2.4.1.7
The counter associated with the number of Background Block Errors encountered on far end of interface in the current interval of type coiOtnFarEndCurIntervalType.
OBJECT-TYPE    
  Counter32  

coiOtnFarEndCurrentESRs 1.3.6.1.4.1.9.9.639.1.2.4.1.8
The counter associated with the Errored Seconds Ratio on far end of interface in the current interval of type coiOtnFarEndCurIntervalType.
OBJECT-TYPE    
  Counter32  

coiOtnFarEndCurrentSESRs 1.3.6.1.4.1.9.9.639.1.2.4.1.9
The counter associated with the Severely Errored Seconds ratio on far end of interface in the current interval of type coiOtnFarEndCurIntervalType.
OBJECT-TYPE    
  Counter32  

coiOtnFarEndCurrentBBERs 1.3.6.1.4.1.9.9.639.1.2.4.1.10
The counter associated with the Background Block Errors ratio on far end of interface in the current interval of type coiOtnFarEndCurIntervalType.
OBJECT-TYPE    
  Counter32  

coiOtnNearEndIntervalTable 1.3.6.1.4.1.9.9.639.1.2.5
This table contains historical cumulative OTN (G.709) PM stats for the near end of interfaces of ifType opticalChannel(195), for the interval type identified by the index coiOtnNearEndIntervalType and the interval number as identified by the index coiOtnNearEndIntervalNum. The PM statistics is the accumlated stats for the time period defined by the interval type in the time interval as defined by interval number.
OBJECT-TYPE    
  SEQUENCE OF  
    CoiOtnNearEndIntervalEntry

coiOtnNearEndIntervalEntry 1.3.6.1.4.1.9.9.639.1.2.5.1
An entry containing management information on near end error/statistics counters such as Failure Counts, Errored Seconds...etc in the given interval.
OBJECT-TYPE    
  CoiOtnNearEndIntervalEntry  

coiOtnNearEndIntervalType 1.3.6.1.4.1.9.9.639.1.2.5.1.1
This object gives the interval type during which the performance statistics are accumulated.
OBJECT-TYPE    
  CoiIntervalType  

coiOtnNearEndIntervalMonType 1.3.6.1.4.1.9.9.639.1.2.5.1.2
This object gives the part of optical network for which near end OTN performance statistics are being monitored.
OBJECT-TYPE    
  CoiMonitorType  

coiOtnNearEndIntervalNum 1.3.6.1.4.1.9.9.639.1.2.5.1.3
This object identifies the interval for which the set of near end OTN performance values is available. The interval identified by 1 is the most recent 15 minute or 24 hour interval, and the interval identified by N is the interval immediately preceding the one identified by N-1.
OBJECT-TYPE    
  Integer32 1..96  

coiOtnNearEndIntervalFCs 1.3.6.1.4.1.9.9.639.1.2.5.1.4
The counter associated with the number of failures encountered on the near end of interface in the interval identified by coiOtnNearEndIntervalType and coiOtnNearEndIntervalNum.
OBJECT-TYPE    
  Counter32  

coiOtnNearEndIntervalESs 1.3.6.1.4.1.9.9.639.1.2.5.1.5
The counter associated with the number of Errored Seconds encountered on the near end of interface in the interval identified by coiOtnNearEndIntervalType and coiOtnNearEndIntervalNum.
OBJECT-TYPE    
  Counter32  

coiOtnNearEndIntervalSESs 1.3.6.1.4.1.9.9.639.1.2.5.1.6
The counter associated with the number of Severely Errored Seconds encountered on the near end of interface in the interval identified by coiOtnNearEndIntervalType and coiOtnNearEndIntervalNum.
OBJECT-TYPE    
  Counter32  

coiOtnNearEndIntervalUASs 1.3.6.1.4.1.9.9.639.1.2.5.1.7
The counter associated with the number of Unavailable Seconds encountered on the near end of interface in the interval identified by coiOtnNearEndIntervalType and coiOtnNearEndIntervalNum.
OBJECT-TYPE    
  Counter32  

coiOtnNearEndIntervalBBEs 1.3.6.1.4.1.9.9.639.1.2.5.1.8
The counter associated with the number of Background Block Errors encountered on the near end of interface in the interval identified by coiOtnNearEndIntervalType and coiOtnNearEndIntervalNum.
OBJECT-TYPE    
  Counter32  

coiOtnNearEndIntervalESRs 1.3.6.1.4.1.9.9.639.1.2.5.1.9
The counter associated with the Errored Seconds Ratio on the near end of interface in the interval identified by coiiOtnNearEndIntervalType and coiOtnNearEndIntervalNum.
OBJECT-TYPE    
  Counter32  

coiOtnNearEndIntervalSESRs 1.3.6.1.4.1.9.9.639.1.2.5.1.10
The counter associated with the Severely Errored Seconds ratio on the near end of interface in the interval identified by coiOtnNearEndIntervalType and coiOtnNearEndIntervalNum.
OBJECT-TYPE    
  Counter32  

coiOtnNearEndIntervalBBERs 1.3.6.1.4.1.9.9.639.1.2.5.1.11
The counter associated with the Background Block Errors ratio on the near end of interface in the interval identified by coiOtnNearEndIntervalType and coiOtnNearEndIntervalNum.
OBJECT-TYPE    
  Counter32  

coiOtnNearEndIntervalValidData 1.3.6.1.4.1.9.9.639.1.2.5.1.12
This variable indicates if the data for the interval identified by coiOtnNearEndIntervalType and coiOtnNearEndIntervalNum is valid.
OBJECT-TYPE    
  TruthValue  

coiOtnFarEndIntervalTable 1.3.6.1.4.1.9.9.639.1.2.6
This table contains historical cumulative OTN (G.709) PM stats for the far end interfaces of ifType opticalChannel(195), for the interval type identified by the index coiOtnFarEndIntervalType and the interval number as identified by coiOtnFarEndIntervalNum. The PM statistics is the accumlated stats for the time period defined by the interval type in the time interval as defined by interval number.
OBJECT-TYPE    
  SEQUENCE OF  
    CoiOtnFarEndIntervalEntry

coiOtnFarEndIntervalEntry 1.3.6.1.4.1.9.9.639.1.2.6.1
An entry containing managment information on far end error/statistics counters such as Failure Counts, Errored Seconds...etc in the given interval
OBJECT-TYPE    
  CoiOtnFarEndIntervalEntry  

coiOtnFarEndIntervalType 1.3.6.1.4.1.9.9.639.1.2.6.1.1
This object gives the interval type during which the far end performance statistics are accumulated.
OBJECT-TYPE    
  CoiIntervalType  

coiOtnFarEndIntervalMonType 1.3.6.1.4.1.9.9.639.1.2.6.1.2
This object gives the part of optical network for which far end OTN performance statistics are being monitored.
OBJECT-TYPE    
  CoiMonitorType  

coiOtnFarEndIntervalNum 1.3.6.1.4.1.9.9.639.1.2.6.1.3
This object identifies the interval for which the set of far end OTN performance values for this interface is available. The interval identified by 1 is the most recent 15 minute or 24 hour interval, and the interval identified by N is the interval immediately preceding the one identified by N-1.
OBJECT-TYPE    
  Integer32 1..96  

coiOtnFarEndIntervalFCs 1.3.6.1.4.1.9.9.639.1.2.6.1.4
The counter associated with the number of Failures encountered on the far end of interface in the interval identified by coiOtnFarEndIntervalType and coiOtnFarEndIntervalNum.
OBJECT-TYPE    
  Counter32  

coiOtnFarEndIntervalESs 1.3.6.1.4.1.9.9.639.1.2.6.1.5
The counter associated with the number of Errored Seconds encountered on far end of interface in the interval identified by coiOtnFarEndIntervalType and coiOtnFarEndIntervalNum.
OBJECT-TYPE    
  Counter32  

coiOtnFarEndIntervalSESs 1.3.6.1.4.1.9.9.639.1.2.6.1.6
The counter associated with the number of Severely Errored Seconds encountered on far end interface in the interval identified by coiOtnFarEndIntervalType and coiOtnFarEndIntervalNum.
OBJECT-TYPE    
  Counter32  

coiOtnFarEndIntervalUASs 1.3.6.1.4.1.9.9.639.1.2.6.1.7
The counter associated with the number of Unavailable Seconds encountered on far end of interface in the interval identified by coiOtnFarEndIntervalType and coiOtnFarEndIntervalNum.
OBJECT-TYPE    
  Counter32  

coiOtnFarEndIntervalBBEs 1.3.6.1.4.1.9.9.639.1.2.6.1.8
The counter associated with the number of Background Block Errors encountered on far end of interface in the interval identified by coiOtnFarEndIntervalType and coiOtnFarEndIntervalNum.
OBJECT-TYPE    
  Counter32  

coiOtnFarEndIntervalESRs 1.3.6.1.4.1.9.9.639.1.2.6.1.9
The counter associated with the Errored Seconds Ratio on far end of interface in the interval identified by coiOtnFarEndIntervalType and coiOtnFarEndIntervalNum.
OBJECT-TYPE    
  Counter32  

coiOtnFarEndIntervalSESRs 1.3.6.1.4.1.9.9.639.1.2.6.1.10
The counter associated with the Severely Errored Seconds ratio on far end of interface in the interval identified by coiOtnFarEndIntervalType and coiOtnFarEndIntervalNum.
OBJECT-TYPE    
  Counter32  

coiOtnFarEndIntervalBBERs 1.3.6.1.4.1.9.9.639.1.2.6.1.11
The counter associated with the Background Block Errors ratio on far end of interface in the interval identified by coiOtnFarEndIntervalType and coiOtnFarEndIntervalNum.
OBJECT-TYPE    
  Counter32  

coiOtnFarEndIntervalValidData 1.3.6.1.4.1.9.9.639.1.2.6.1.12
This variable indicates if the far end data for the interval identified by coiOtnFarEndIntervalType and coiOtnFarEndIntervalNum is valid.
OBJECT-TYPE    
  TruthValue  

coiDwdmIfFEC 1.3.6.1.4.1.9.9.639.1.3
OBJECT IDENTIFIER    

coiFECThresholdsTable 1.3.6.1.4.1.9.9.639.1.3.1
This table contains the configurable thresholds for FEC ( Forward Error Correction ) statistics.
OBJECT-TYPE    
  SEQUENCE OF  
    CoiFECThresholdsEntry

coiFECThresholdsEntry 1.3.6.1.4.1.9.9.639.1.3.1.1
An entry containing management information for configuration of FEC thresholds. Entries can be created for ifIndices with an ifType of opticalChannel(195). Thresholds are created/destroyed, through the entry's RowStatus object semantics. The coiFECThreshIntervalType defines the time interval over which the data being monitored is accumulated for which the threshold is to be applied. The coiFECThreshType defines the specific threshold type value, which the threshold refers to.
OBJECT-TYPE    
  CoiFECThresholdsEntry  

coiFECThreshIntervalType 1.3.6.1.4.1.9.9.639.1.3.1.1.1
This object gives the type of the interval for which the thresholds are being set.
OBJECT-TYPE    
  CoiIntervalType  

coiFECThreshType 1.3.6.1.4.1.9.9.639.1.3.1.1.2
This object gives the type of the FEC Threshold that is being set. Valid values are - bitErrCor(1) : Bit Errors Corrected byteErrcor(2) : Byte Errors Corrected zeroErrDet(3) : Zero Bit Errors Detected oneErrDet(4) : One Bit Errors Detected unCorWords(5) : Un Correctable Words
OBJECT-TYPE    
  INTEGER bitErrCor(1), byteErrcor(2), zeroErrDet(3), oneErrDet(4), unCorWords(5)  

coiFECThreshValue 1.3.6.1.4.1.9.9.639.1.3.1.1.3
This object is used for configuring the FEC threshold value for the given threshold type.
OBJECT-TYPE    
  Unsigned32  

coiFECThreshStorageType 1.3.6.1.4.1.9.9.639.1.3.1.1.4
The storage type for this conceptual row.
OBJECT-TYPE    
  StorageType  

coiFECThreshStatus 1.3.6.1.4.1.9.9.639.1.3.1.1.5
This object controls the creation and deletion of a conceptual row in this table.The RowStatus TC requires that this DESCRIPTION clause states under which circumstances other objects in this row can be modified. The value of this object has no effect on whether other objects in this conceptual row can be modified. A conceptual row can not be made active until atleast coiFECThreshValueLSB has been set to a valid threshold value.
OBJECT-TYPE    
  RowStatus  

coiFECCurrentTable 1.3.6.1.4.1.9.9.639.1.3.2
This table contains the cumulative FEC PM stats for the interfaces of ifType opticalChannel(195) for the current interval of interval type identified coiFECCurIntervalType.
OBJECT-TYPE    
  SEQUENCE OF  
    CoiFECCurrentEntry

coiFECCurrentEntry 1.3.6.1.4.1.9.9.639.1.3.2.1
An entry containing managment information on FEC related error/statistics counters such as Bit Errors Corrected, Byte Errors Corrected etc in the current interval.
OBJECT-TYPE    
  CoiFECCurrentEntry  

coiFECCurIntervalType 1.3.6.1.4.1.9.9.639.1.3.2.1.1
This object gives the interval type during which the FEC PM statistics have been collected.
OBJECT-TYPE    
  CoiIntervalType  

coiFECCurrentCorBitErrs 1.3.6.1.4.1.9.9.639.1.3.2.1.2
The counter associated with the number of Bit Errors Corrected on this interface in the current interval of type coiFECCurIntervalType.
OBJECT-TYPE    
  Counter64  

coiFECCurrentCorByteErrs 1.3.6.1.4.1.9.9.639.1.3.2.1.3
The counter associated with the number of Byte Errors Corrected on this interface in the current interval of type coiFECCurIntervalType.
OBJECT-TYPE    
  Counter64  

coiFECCurrentDetZeroErrs 1.3.6.1.4.1.9.9.639.1.3.2.1.4
The counter associated with the number of zero bit errors detected on this interface in the current interval of type coiFECCurIntervalType.
OBJECT-TYPE    
  Counter64  

coiFECCurrentDetOneErrs 1.3.6.1.4.1.9.9.639.1.3.2.1.5
The counter associated with the number of one bit errors detected on this interface in the current interval of type coiFECCurIntervalType.
OBJECT-TYPE    
  Counter64  

coiFECCurrentUncorWords 1.3.6.1.4.1.9.9.639.1.3.2.1.6
The counter associated with the number of Uncorrectable Words encountered on this interface in the current interval of type coiFECCurIntervalType.
OBJECT-TYPE    
  Counter64  

coiFECIntervalTable 1.3.6.1.4.1.9.9.639.1.3.3
This table contains historical cumulative FEC PM stats for the interfaces of ifType opticalChannel(195), for the interval type identified by the index coiFECIntervalType and the interval number as identified by index coiFECIntervalNum. The PM statistics is the accumlated stats for the time period defined by the interval type in the time interval as defined by interval number.
OBJECT-TYPE    
  SEQUENCE OF  
    CoiFECIntervalEntry

coiFECIntervalEntry 1.3.6.1.4.1.9.9.639.1.3.3.1
An entry containing managment information on FEC error/statistics counters such as Bit Errors Corrected, Byte Errors Corrected etc in the given interval.
OBJECT-TYPE    
  CoiFECIntervalEntry  

coiFECIntervalType 1.3.6.1.4.1.9.9.639.1.3.3.1.1
This object gives the type of interval for which the FEC values have been collected.
OBJECT-TYPE    
  CoiIntervalType  

coiFECIntervalNum 1.3.6.1.4.1.9.9.639.1.3.3.1.2
This object gives the interval for which the set of FEC PM values are available. The interval identified by 1 is the most recent 15 minute or 24 hour interval, and the interval identified by N is the interval immediately preceding the one identified by N-1.
OBJECT-TYPE    
  Integer32 1..96  

coiFECIntervalCorBitErrs 1.3.6.1.4.1.9.9.639.1.3.3.1.3
The counter associated with the number of Bit Errors Corrected in the interval identified by coiFECIntervalType and coiFECIntervalNum.
OBJECT-TYPE    
  Counter64  

coiFECIntervalCorByteErrs 1.3.6.1.4.1.9.9.639.1.3.3.1.4
The counter associated with the number of Byte Errors Corrected on this interface in the interval identified by coiFECIntervalType and coiFECIntervalNum.
OBJECT-TYPE    
  Counter64  

coiFECIntervalDetZeroErrs 1.3.6.1.4.1.9.9.639.1.3.3.1.5
The counter associated with the number of zero bit errors detected on this interface in the interval identified by coiFECIntervalType and coiFECIntervalNum.
OBJECT-TYPE    
  Counter64  

coiFECIntervalDetOneErrs 1.3.6.1.4.1.9.9.639.1.3.3.1.6
The counter associated with the number of one bit errors detected on this interface in the interval identified by coiFECIntervalType and coiFECIntervalNum.
OBJECT-TYPE    
  Counter64  

coiFECIntervalUncorWords 1.3.6.1.4.1.9.9.639.1.3.3.1.7
The counter associated with the number of Uncorrectable Words encountered on this interface in the interval identified by coiFECIntervalType and coiFECIntervalNum.
OBJECT-TYPE    
  Counter64  

coiFECIntervalValidData 1.3.6.1.4.1.9.9.639.1.3.3.1.8
This object indicates whether the data for the interval identified by coiFECIntervalType and coiFECIntervalNum is valid.
OBJECT-TYPE    
  TruthValue  

ciscoOtnIfMIBConformance 1.3.6.1.4.1.9.9.639.2
OBJECT IDENTIFIER    

ciscoOtnIfMIBCompliances 1.3.6.1.4.1.9.9.639.2.1
OBJECT IDENTIFIER    

ciscoOtnIfMIBCompliance 1.3.6.1.4.1.9.9.639.2.1.1
The compliance statement for platforms that monitor the operating status and FEC/OTN with respect to error counters, for the physical layer.
MODULE-COMPLIANCE    

ciscoOtnIfMIBGroups 1.3.6.1.4.1.9.9.639.2.2
OBJECT IDENTIFIER    

coiIfControllerGroup 1.3.6.1.4.1.9.9.639.2.2.1
The collection of objects to allow configurations and give information related to the physical layer characteristics for interfaces of ifType opticalChannel(195).
OBJECT-GROUP    

coiIfOtnNearEndCurrentGroup 1.3.6.1.4.1.9.9.639.2.2.3
The collection of objects used for monitoring the near end OTN error counters in the current interval.
OBJECT-GROUP    

coiIfOtnNearEndIntervalGroup 1.3.6.1.4.1.9.9.639.2.2.4
The collection of objects used for monitoring the near end OTN error counters in a given interval.
OBJECT-GROUP    

coiIfOtnFarEndCurrentGroup 1.3.6.1.4.1.9.9.639.2.2.5
The collection of objects used for monitoring the far end OTN error counters in the current interval.
OBJECT-GROUP    

coiIfOtnFarEndIntervalGroup 1.3.6.1.4.1.9.9.639.2.2.6
The collection of objects used for monitoring the far end OTN error counters in a given interval.
OBJECT-GROUP    

coiIfOtnGroup 1.3.6.1.4.1.9.9.639.2.2.7
The collection of objects used for monitoring the OTN error counters.
OBJECT-GROUP    

coiIfFECGroup 1.3.6.1.4.1.9.9.639.2.2.8
The collection objects used for monitoring the FEC error counters.
OBJECT-GROUP    

coiIfFECCurrentGroup 1.3.6.1.4.1.9.9.639.2.2.9
The collection of objects used for monitoring the FEC error counters in the current interval.
OBJECT-GROUP    

coiIfFECIntervalGroup 1.3.6.1.4.1.9.9.639.2.2.10
The collection of objects used for monitoring the FEC error counters in a given interval .
OBJECT-GROUP    

Defined Objects

CoiIntervalType  
This value indicates the time period over which performance monitoring data has been collected. Valid values are - fifteenMin(1) - values for the 15 min interval. oneDay(2) - values for the 1 Day interval.
TEXTUAL-CONVENTION    
  INTEGER fifteenMin(1), oneDay(2)  

CoiMonitorType  
This value indicates the part of the optical network in which the performance statistics is being monitored. Valid values are - path(1) - Performance statistics for path parameters. section(2) - Performance statistics for section parameters. tcm1(3) - Performance statistics for tandem connection monitoring 1. tcm2(4) - Performance statistics for tandem connection monitoring 2.
TEXTUAL-CONVENTION    
  INTEGER path(1), section(2), tcm1(3), tcm2(4)  

CoiOtnThresholdType  
This value indicates the type of OTN Error Thresholds that can be defined. Valid values are - fc(1) - Failure Counts. es(2) - Errored Seconds. ses(3) - Severely Errored Seconds. uas(4) - Unavailable Seconds. bbe(5) - Bit Block Errors. esr(6) - Error Seconds Ratio. sesr(7) - Severely Errored Seconds Ratio. bber(8) - Background Block Errored Seconds Ratio.
TEXTUAL-CONVENTION    
  INTEGER fc(1), es(2), ses(3), uas(4), bbe(5), esr(6), sesr(7), bber(8)  

CoiOpticalWavelength  
This value represents the wavelength of optical signals in a DWDM optical channel. It is represented in units of picometers. A value of zero either indicates that the wavelength is unknown, or that it does not fall under the frequency grid defined in ITU-T G.694.1
TEXTUAL-CONVENTION    
  Unsigned32 0 | 1528770..1604030  

CoiIfControllerEntry  
SEQUENCE    
  INTEGER as coiIfControllerLoopback  
  CoiOpticalWavelength as coiIfControllerWavelength  
  INTEGER as coiIfControllerLaserAdminStatus  
  INTEGER as coiIfControllerLaserOperStatus  
  TruthValue as coiIfControllerOtnStatus  
  INTEGER as coiIfControllerFECMode  
  INTEGER as coiIfControllerTDCOperMode  
  INTEGER as coiIfControllerTDCOperStatus  
  Integer32 as coiIfControllerTDCOperSetting  
  Integer32 as coiIfControllerPreFECBERMantissa  
  Integer32 as coiIfControllerPreFECBERExponent  
  Integer32 as coiIfControllerQFactor  
  Integer32 as coiIfControllerQMargin  
  Unsigned32 as coiIfControllerOTNValidIntervals  
  Unsigned32 as coiIfControllerFECValidIntervals  

CoiOtnNearEndThresholdsEntry  
SEQUENCE    
  CoiIntervalType as coiOtnNearEndThreshIntervalType  
  CoiMonitorType as coiOtnNearEndThreshMonType  
  CoiOtnThresholdType as coiOtnNearEndThresholdType  
  Unsigned32 as coiOtnNearEndThreshValue  
  StorageType as coiOtnNearEndThreshStorageType  
  RowStatus as coiOtnNearEndThreshStatus  

CoiOtnFarEndThresholdsEntry  
SEQUENCE    
  CoiIntervalType as coiOtnFarEndThreshIntervalType  
  CoiMonitorType as coiOtnFarEndThreshMonType  
  CoiOtnThresholdType as coiOtnFarEndThresholdType  
  Unsigned32 as coiOtnFarEndThreshValue  
  StorageType as coiOtnFarEndThreshStorageType  
  RowStatus as coiOtnFarEndThreshStatus  

CoiOtnNearEndCurrentEntry  
SEQUENCE    
  CoiIntervalType as coiOtnNearEndCurIntervalType  
  CoiMonitorType as coiOtnNearEndCurrentMonType  
  Counter32 as coiOtnNearEndCurrentFCs  
  Counter32 as coiOtnNearEndCurrentESs  
  Counter32 as coiOtnNearEndCurrentSESs  
  Counter32 as coiOtnNearEndCurrentUASs  
  Counter32 as coiOtnNearEndCurrentBBEs  
  Counter32 as coiOtnNearEndCurrentESRs  
  Counter32 as coiOtnNearEndCurrentSESRs  
  Counter32 as coiOtnNearEndCurrentBBERs  

CoiOtnFarEndCurrentEntry  
SEQUENCE    
  CoiIntervalType as coiOtnFarEndCurIntervalType  
  CoiMonitorType as coiOtnFarEndCurrentMonType  
  Counter32 as coiOtnFarEndCurrentFCs  
  Counter32 as coiOtnFarEndCurrentESs  
  Counter32 as coiOtnFarEndCurrentSESs  
  Counter32 as coiOtnFarEndCurrentUASs  
  Counter32 as coiOtnFarEndCurrentBBEs  
  Counter32 as coiOtnFarEndCurrentESRs  
  Counter32 as coiOtnFarEndCurrentSESRs  
  Counter32 as coiOtnFarEndCurrentBBERs  

CoiOtnNearEndIntervalEntry  
SEQUENCE    
  CoiIntervalType as coiOtnNearEndIntervalType  
  CoiMonitorType as coiOtnNearEndIntervalMonType  
  Integer32 as coiOtnNearEndIntervalNum  
  Counter32 as coiOtnNearEndIntervalFCs  
  Counter32 as coiOtnNearEndIntervalESs  
  Counter32 as coiOtnNearEndIntervalSESs  
  Counter32 as coiOtnNearEndIntervalUASs  
  Counter32 as coiOtnNearEndIntervalBBEs  
  Counter32 as coiOtnNearEndIntervalESRs  
  Counter32 as coiOtnNearEndIntervalSESRs  
  Counter32 as coiOtnNearEndIntervalBBERs  
  TruthValue as coiOtnNearEndIntervalValidData  

CoiOtnFarEndIntervalEntry  
SEQUENCE    
  CoiIntervalType as coiOtnFarEndIntervalType  
  CoiMonitorType as coiOtnFarEndIntervalMonType  
  Integer32 as coiOtnFarEndIntervalNum  
  Counter32 as coiOtnFarEndIntervalFCs  
  Counter32 as coiOtnFarEndIntervalESs  
  Counter32 as coiOtnFarEndIntervalSESs  
  Counter32 as coiOtnFarEndIntervalUASs  
  Counter32 as coiOtnFarEndIntervalBBEs  
  Counter32 as coiOtnFarEndIntervalESRs  
  Counter32 as coiOtnFarEndIntervalSESRs  
  Counter32 as coiOtnFarEndIntervalBBERs  
  TruthValue as coiOtnFarEndIntervalValidData  

CoiFECThresholdsEntry  
SEQUENCE    
  CoiIntervalType as coiFECThreshIntervalType  
  INTEGER as coiFECThreshType  
  Unsigned32 as coiFECThreshValue  
  StorageType as coiFECThreshStorageType  
  RowStatus as coiFECThreshStatus  

CoiFECCurrentEntry  
SEQUENCE    
  CoiIntervalType as coiFECCurIntervalType  
  Counter64 as coiFECCurrentCorBitErrs  
  Counter64 as coiFECCurrentCorByteErrs  
  Counter64 as coiFECCurrentDetZeroErrs  
  Counter64 as coiFECCurrentDetOneErrs  
  Counter64 as coiFECCurrentUncorWords  

CoiFECIntervalEntry  
SEQUENCE    
  CoiIntervalType as coiFECIntervalType  
  Integer32 as coiFECIntervalNum  
  Counter64 as coiFECIntervalCorBitErrs  
  Counter64 as coiFECIntervalCorByteErrs  
  Counter64 as coiFECIntervalDetZeroErrs  
  Counter64 as coiFECIntervalDetOneErrs  
  Counter64 as coiFECIntervalUncorWords  
  TruthValue as coiFECIntervalValidData