
CISCO-SSM-PROV-MIB
File:
CISCO-SSM-PROV-MIB.mib (12579 bytes)
Imported modules
Imported symbols
Defined Objects
| ciscoSsmProvMIB |
1.3.6.1.4.1.9.9.448 |
| This MIB is used to provision features on a Data Path Processor (DPP) of a Storage Service Module (SSM). A DPP is assigned to a contiguous set of ports. Each DPP can run one or more features independent of other DPPs on the module. Since the concept of a DPP is transparent to the network manager, ranges of ports are used to configure different features. A start and an end port are specified to identify a DPP and provision a feature. |
| MODULE-IDENTITY |
|
|
|
| ssmProvFeatureEntry |
1.3.6.1.4.1.9.9.448.1.1.1.1 |
| An entry in the ssmProvFeatureTable that contains information on the features that can be configured on an SSM. |
| OBJECT-TYPE |
|
|
|
| |
SsmProvFeatureEntry |
|
|
| ssmProvFeatureNeedsImage |
1.3.6.1.4.1.9.9.448.1.1.1.1.2 |
| The object indicates if the feature needs an image name to be specified during provisioning. If the value of this object is 'true', then an image needs to be specified. If the value of this object is 'false', then an image does not need to be specified. |
| OBJECT-TYPE |
|
|
|
| |
TruthValue |
|
|
| ssmProvFeatureIfTable |
1.3.6.1.4.1.9.9.448.1.1.2 |
| A table containing feature related information for interfaces. This table gives a list of interfaces that are assigned to different features. The interfaces supported are of the type fibreChannel. If a feature is removed from ssmProvFeatureTable, then corresponding entries in ssmProvFeatureIfTable will also get removed. |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
SsmProvFeatureIfEntry |
|
| ssmProvFeatureIfEntry |
1.3.6.1.4.1.9.9.448.1.1.2.1 |
| This contains information on the SSM-feature membership of a interface. |
| OBJECT-TYPE |
|
|
|
| |
SsmProvFeatureIfEntry |
|
|
| ssmProvFeatureIfForceRemove |
1.3.6.1.4.1.9.9.448.1.1.2.1.4 |
| This object indicates if the provisioning should be forcefully removed. The object must be set concurrently with setting the corresponding instance of ssmProvFeatureIfRowStatus to 'destroy'. The 'forceReset' option will cause the configuration to be removed and the SSM card to be reset in the process. No action is taken if this object is set to 'noop'. The value of this object when read is always 'noop'. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
forceReset(1), noop(2) |
|
| ssmProvFeatureIfPartnerImageURI |
1.3.6.1.4.1.9.9.448.1.1.2.1.5 |
| The object representing the location on the local system, from where the partner image will be picked for installation. The value of this object is only relevant if the ssmProvFeatureNeedsImage object is set to 'true' for that feature in ssmProvFeatureTable. |
| OBJECT-TYPE |
|
|
|
| |
SnmpAdminString |
SIZE(1..80) |
|
| ssmProvDppTable |
1.3.6.1.4.1.9.9.448.1.1.3 |
| A table containing DPP information for interfaces. This table gives a list of DPPs for every interface. Entries get added to the table when an SSM comes online and removed when it goes offline. |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
SsmProvDppEntry |
|
| ssmProvDppEntry |
1.3.6.1.4.1.9.9.448.1.1.3.1 |
| This contains information on the DPP to interface association. |
| OBJECT-TYPE |
|
|
|
| |
SsmProvDppEntry |
|
|
Defined Objects
| SsmProvFeatureEntry |
|
| SEQUENCE |
|
|
|
| |
SnmpAdminString as ssmProvFeatureName |
|
|
| |
TruthValue as ssmProvFeatureNeedsImage |
|
|
| SsmProvFeatureIfEntry |
|
| SEQUENCE |
|
|
|
| |
InterfaceIndex as ssmProvFeatureIfStartPort |
|
|
| |
InterfaceIndex as ssmProvFeatureIfEndPort |
|
|
| |
SnmpAdminString as ssmProvFeatureIfFeatureName |
|
|
| |
INTEGER as ssmProvFeatureIfForceRemove |
|
|
| |
SnmpAdminString as ssmProvFeatureIfPartnerImageURI |
|
|
| |
RowStatus as ssmProvFeatureIfRowStatus |
|
|
| SsmProvDppEntry |
|
| SEQUENCE |
|
|
|
| |
InterfaceIndex as ssmProvDppStartPort |
|
|
| |
InterfaceIndex as ssmProvDppEndPort |
|
|
| |
SnmpAdminString as ssmProvDppName |
|
|