CISCO-SWITCH-ENGINE-MIB

File: CISCO-SWITCH-ENGINE-MIB.mib (213004 bytes)

Imported modules

SNMPv2-SMI IF-MIB CISCO-TC
CISCO-SMI CISCO-VTP-MIB INET-ADDRESS-MIB
ENTITY-MIB SNMPv2-TC SNMP-FRAMEWORK-MIB
MPLS-VPN-MIB SNMPv2-CONF

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Gauge32
Counter32 Counter64 IpAddress
Integer32 Unsigned32 ifIndex
OwnerString InterfaceIndexOrZero CiscoNetworkProtocol
CiscoPort ciscoMgmt VlanIndex
InetAddressType InetAddress entPhysicalIndex
TEXTUAL-CONVENTION DisplayString RowStatus
TimeInterval MacAddress TruthValue
TimeStamp SnmpAdminString MplsVpnId
MODULE-COMPLIANCE OBJECT-GROUP

Defined Objects

ciscoSwitchEngineMIB 1.3.6.1.4.1.9.9.97
This MIB module defines management objects for Cisco Layer 2/3 switches. These devices may either have a single (central) switching engine entity or may consist of multiple (distributed) switching engine entities which are inter-connected via a common 'switching fabric'. In the central switching engine model, all the physical ports in the system are handled by the only switching engine in the system. In the distributed switching model, each switching engine will handle a set of 'local' physical ports and when necessary, packets are also switched between switching engines over the switching fabric. Cisco L2/L3 switching devices use regular routers to assist them in learning packet 'flows' by observing how a router routes a candidate flow. A flow is some combination of source network address, destination network address and the transport port numbers, as applicable. Once a flow is established (learned), all traffic belonging to that flow will be switched at Layer 3 by the switch engine, effectively bypassing the router, until the flow has been 'aged' out. Most Cisco L2/L3 switching devices employ built-in (internal) router module(s) for integrating Layer 3 switching with Layer 2 forwarding. However, they can also learn 'flows' through other physically-separate (external) Cisco routers that are connected to the switch-engine through the network.
MODULE-IDENTITY    

cseMIBObjects 1.3.6.1.4.1.9.9.97.1
OBJECT IDENTIFIER    

cseL2Objects 1.3.6.1.4.1.9.9.97.1.1
OBJECT IDENTIFIER    

cseL2StatsTable 1.3.6.1.4.1.9.9.97.1.1.1
A table containing switching engine's L2 statistics counters.
OBJECT-TYPE    
  SEQUENCE OF  
    CseL2StatsEntry

cseL2StatsEntry 1.3.6.1.4.1.9.9.97.1.1.1.1
A conceptual row containing L2 statistics maintained by a switching engine (identified by entPhysicalIndex). Each switching engine managed by this MIB module has an entry in this table.
OBJECT-TYPE    
  CseL2StatsEntry  

cseL2ForwardedLocalPkts 1.3.6.1.4.1.9.9.97.1.1.1.1.1
Number of packets received from ports local to this switching engine and forwarded at layer 2.
OBJECT-TYPE    
  Counter32  

cseL2ForwardedLocalOctets 1.3.6.1.4.1.9.9.97.1.1.1.1.2
Number of octets in the packets received from ports local to this switching engine and forwarded at layer 2.
OBJECT-TYPE    
  Counter64  

cseL2ForwardedTotalPkts 1.3.6.1.4.1.9.9.97.1.1.1.1.3
Total number of packets received from all sources (local and over the fabric) and forwarded at layer 2 by this switching engine.
OBJECT-TYPE    
  Counter32  

cseL2NewAddressLearns 1.3.6.1.4.1.9.9.97.1.1.1.1.4
Number of new MAC addresses learned by the switching engine.
OBJECT-TYPE    
  Counter32  

cseL2AddrLearnFailures 1.3.6.1.4.1.9.9.97.1.1.1.1.5
Number of MAC addresses failed to be learned because the L2 forwarding address table was full. If the value keeps increasing, the network topology should be reconfigured.
OBJECT-TYPE    
  Counter32  

cseL2DstAddrLookupMisses 1.3.6.1.4.1.9.9.97.1.1.1.1.6
Number of misses during destination MAC address table lookups. A few misses happen normally. Large numbers of misses occur as a result of cseL2AddrLearnFailures.
OBJECT-TYPE    
  Counter32  

cseL2IpPkts 1.3.6.1.4.1.9.9.97.1.1.1.1.7
Number of packets belonging to the IP family received by this switching engine from all sources. This value includes L3 switched packets.
OBJECT-TYPE    
  Counter32  

cseL2IpxPkts 1.3.6.1.4.1.9.9.97.1.1.1.1.8
Number of packets belonging to the IPX family received by this switching engine from all sources. This value includes L3 switched packets.
OBJECT-TYPE    
  Counter32  

cseL2AssignedProtoPkts 1.3.6.1.4.1.9.9.97.1.1.1.1.9
Number of packets belonging to an assigned group of network protocols (typically AppleTalk, DecNet and Vines) received by this switching engine from all sources. This value includes L3 switched packets.
OBJECT-TYPE    
  Counter32  

cseL2OtherProtoPkts 1.3.6.1.4.1.9.9.97.1.1.1.1.10
Number of packets belonging to all other protocol families, received by this switching engine from all sources. This value includes L3 switched packets.
OBJECT-TYPE    
  Counter32  

cseL2StatsHCTable 1.3.6.1.4.1.9.9.97.1.1.2
Contains the High Capacity L2 Statistics extensions to the cseL2StatsTable.
OBJECT-TYPE    
  SEQUENCE OF  
    CseL2StatsHCEntry

cseL2StatsHCEntry 1.3.6.1.4.1.9.9.97.1.1.2.1
Contains the High Capacity L2 Statistics extensions to cseL2StatsEntry. These objects will be created by the agent for all cseL2StatsEntries it deems appropriate.
OBJECT-TYPE    
  CseL2StatsHCEntry  

cseL2HCOverflowForwardedLocalPkts 1.3.6.1.4.1.9.9.97.1.1.2.1.1
The number of times the associated cseL2ForwardedLocalPkts counter has overflowed.
OBJECT-TYPE    
  Counter32  

cseL2HCForwardedLocalPkts 1.3.6.1.4.1.9.9.97.1.1.2.1.2
Number of packets received from ports local to this switching engine and forwarded at layer 2.
OBJECT-TYPE    
  Counter64  

cseL2HCOverflowForwardedTotalPkts 1.3.6.1.4.1.9.9.97.1.1.2.1.3
The number of times the associated cseL2ForwardeTotalPkts counter has overflowed.
OBJECT-TYPE    
  Counter32  

cseL2HCForwardedTotalPkts 1.3.6.1.4.1.9.9.97.1.1.2.1.4
Total number of packets received from all sources (local and over the fabric) and forwarded at layer 2 by this switching engine.
OBJECT-TYPE    
  Counter64  

cseL2HCOverflowIpPkts 1.3.6.1.4.1.9.9.97.1.1.2.1.5
The number of times the associated cseL2IpPkts counter has overflowed.
OBJECT-TYPE    
  Counter32  

cseL2HCIpPkts 1.3.6.1.4.1.9.9.97.1.1.2.1.6
Number of packets belonging to the IP family received by this switching engine from all sources. This value includes L3 switched packets.
OBJECT-TYPE    
  Counter64  

cseL2HCOverflowIpxPkts 1.3.6.1.4.1.9.9.97.1.1.2.1.7
The number of times the associated cseL2IpxPkts counter has overflowed.
OBJECT-TYPE    
  Counter32  

cseL2HCIpxPkts 1.3.6.1.4.1.9.9.97.1.1.2.1.8
Number of packets belonging to the IPX family received by this switching engine from all sources. This value includes L3 switched packets.
OBJECT-TYPE    
  Counter64  

cseL2HCOverflowAssignedProtoPkts 1.3.6.1.4.1.9.9.97.1.1.2.1.9
The number of times the associated cseL2HCAssignedProtoPkts counter has overflowed.
OBJECT-TYPE    
  Counter32  

cseL2HCAssignedProtoPkts 1.3.6.1.4.1.9.9.97.1.1.2.1.10
Number of packets belonging to an assigned group of network protocols (typically AppleTalk, DecNet and Vines) received by this switching engine from all sources. This value includes L3 switched packets.
OBJECT-TYPE    
  Counter64  

cseL2HCOverflowOtherProtoPkts 1.3.6.1.4.1.9.9.97.1.1.2.1.11
The number of times the associated cseL2HCOtherProtoPkts counter has overflowed.
OBJECT-TYPE    
  Counter32  

cseL2HCOtherProtoPkts 1.3.6.1.4.1.9.9.97.1.1.2.1.12
Number of packets belonging to all other protocol families, received by this switching engine from all sources. This value includes L3 switched packets.
OBJECT-TYPE    
  Counter64  

cseFlow 1.3.6.1.4.1.9.9.97.1.2
OBJECT IDENTIFIER    

cseFlowEstablishedAgingTime 1.3.6.1.4.1.9.9.97.1.2.1
The adminstrative aging time for IP established flows. The default value for this object is implementation specific. If the cseFlowEstablishedAgingTime is not configured to the appropriate value, it will be adjusted to the closest value. The corresponding operational object, taken effect on the a device, is cseFlowOperIPEstablishedAgingTime.
OBJECT-TYPE    
  Integer32 1..65535  

cseFlowFastAgingTime 1.3.6.1.4.1.9.9.97.1.2.2
The administrative fast aging time for the established flow entries, that have less number of packets than the value set in the cseFlowFastAgePktThreshold, switched within this time. Setting to value of 0 turns off fast aging. The default value for this object is implementation specific. If the cseFlowFastAgingTime is not configured to the appropriate value, it will be adjusted to the closest value. The corresponding operational object, taken effect on the device, is cseFlowOperFastAgingTime.
OBJECT-TYPE    
  Unsigned32  

cseFlowFastAgePktThreshold 1.3.6.1.4.1.9.9.97.1.2.3
The administrative packet threshold setting for the cseFlowFastAgingTime. The default for Fast Aging Packet Threshold is 0, i.e. no packets switched within the time set in cseFlowFastAgingTime, after an L3 flow was established. If the cseFlowFastAgingTime is not configured to the appropriate value, it will be adjusted to the closest value. The corresponding operational object, taken effect on the device, is cseFlowOperFastAgePktThreshold.
OBJECT-TYPE    
  Unsigned32  

cseRouterTable 1.3.6.1.4.1.9.9.97.1.2.4
A table containing information about all routers that are discovered by the switch, including internal and external routers.
OBJECT-TYPE    
  SEQUENCE OF  
    CseRouterEntry

cseRouterEntry 1.3.6.1.4.1.9.9.97.1.2.4.1
A conceptual row in the cseRouterTable containing information about a router. A row appears either directly through dynamic learning or indirectly through management configuration (via SNMP,by creating an entry in the cseStaticExtRouterTable or via CLI).
OBJECT-TYPE    
  CseRouterEntry  

cseRouterIndex 1.3.6.1.4.1.9.9.97.1.2.4.1.1
The router's IP address which is used to uniquely identify it for L3 flows.
OBJECT-TYPE    
  IpAddress  

cseRouterFlowMask 1.3.6.1.4.1.9.9.97.1.2.4.1.2
The IP type of mask configured for the router represented by this row. Each flow known to the switching engine has a mask which is applied to all packets in order to compare them to that flow. Each hardware-learned flow has the mask configured for the router which logically forwards that flow.
OBJECT-TYPE    
  INTEGER dstOnly(1), srcDst(2), fullFlow(3), notApplicable(4), srcDstVlan(5)  

cseRouterName 1.3.6.1.4.1.9.9.97.1.2.4.1.3
DNS name (if available) of the router.
OBJECT-TYPE    
  DisplayString  

cseRouterStatic 1.3.6.1.4.1.9.9.97.1.2.4.1.4
If the value of the object is true, this router was configured via SNMP or CLI. Otherwise, this router was learned automatically.
OBJECT-TYPE    
  TruthValue  

cseRouterIpxFlowMask 1.3.6.1.4.1.9.9.97.1.2.4.1.5
The IPX type of mask configured for the router represented by this row. Each flow known to the switching engine has a mask which is applied to all packets in order to compare them to that flow. Each hardware-learned flow has the mask configured for the router which logically forwards that flow.
OBJECT-TYPE    
  INTEGER dstOnly(1), srcDst(2), fullFlow(3), notApplicable(4)  

cseStaticExtRouterTable 1.3.6.1.4.1.9.9.97.1.2.5
A table of external routers which are enabled for Layer 3 IP switching by the switching engine. This table may contain routers that have not yet been discovered by the device.
OBJECT-TYPE    
  SEQUENCE OF  
    CseStaticExtRouterEntry

cseStaticExtRouterEntry 1.3.6.1.4.1.9.9.97.1.2.5.1
A conceptual row in the cseStaticExtRouterTable for enabling an external router to be installed in the switch's router table. The entry is created and deleted by using cseStaticRouterStatus.
OBJECT-TYPE    
  CseStaticExtRouterEntry  

cseStaticRouterName 1.3.6.1.4.1.9.9.97.1.2.5.1.1
DNS name (if available) of the external router.
OBJECT-TYPE    
  DisplayString  

cseStaticRouterOwner 1.3.6.1.4.1.9.9.97.1.2.5.1.2
String indicating the owner who created the static entry.
OBJECT-TYPE    
  OwnerString  

cseStaticRouterStatus 1.3.6.1.4.1.9.9.97.1.2.5.1.3
Used to manage creation and deletion of rows in this table. Once a row becomes active, values within that row cannot be modified except by deleting and creating the row.
OBJECT-TYPE    
  RowStatus  

cseStaticRouterType 1.3.6.1.4.1.9.9.97.1.2.5.1.4
Indicates if the router is included for unicast switching, or multicast switching, or both.
OBJECT-TYPE    
  BITS unicast(0), multicast(1)  

cseRouterVlanTable 1.3.6.1.4.1.9.9.97.1.2.6
The table listing the MAC address used by routers on particular VLANs.
OBJECT-TYPE    
  SEQUENCE OF  
    CseRouterVlanEntry

cseRouterVlanEntry 1.3.6.1.4.1.9.9.97.1.2.6.1
A conceptual row of the cseRouterVlanTable. An entry exists for each known VLAN of each known router.
OBJECT-TYPE    
  CseRouterVlanEntry  

cseRouterMac 1.3.6.1.4.1.9.9.97.1.2.6.1.1
Mac address used by the router for this VLAN number.
OBJECT-TYPE    
  MacAddress  

cseRouterVlan 1.3.6.1.4.1.9.9.97.1.2.6.1.2
The Vlan number associated with the router's MAC address.
OBJECT-TYPE    
  VlanIndex  

cseRouterProtocol 1.3.6.1.4.1.9.9.97.1.2.6.1.3
Indicates which protocols are routed by this router on this VLAN using this Mac address.
OBJECT-TYPE    
  BITS ip(0), ipx(1)  

cseFlowMaxQueries 1.3.6.1.4.1.9.9.97.1.2.7
Maximum number of query entries allowed to be outstanding at any time, in the cseFlowQueryTable. The typical value for this object is 5.
OBJECT-TYPE    
  Unsigned32  

cseFlowQueryTable 1.3.6.1.4.1.9.9.97.1.2.8
A control table used to query the switching engine by specifying retrieval criteria for L3 flows. The resulting data for each instance of a query in this table is returned in the cseFlowDataTable. The maximum number of entries (rows) in this table cannot exceed the value returned by cseFlowMaxQueries.
OBJECT-TYPE    
  SEQUENCE OF  
    CseFlowQueryEntry

cseFlowQueryEntry 1.3.6.1.4.1.9.9.97.1.2.8.1
A conceptual row of the cesFlowQueryTable used to setup retrieval criteria to search for L3 flows on a particular switching engine entity identified by entPhysicalIndex. The actual search is started by setting the value of cseFlowQueryStatus to 'active'. Once a row becomes active, values within the row cannot be modified, except by deleting and re-creating the row.
OBJECT-TYPE    
  CseFlowQueryEntry  

cseFlowQueryIndex 1.3.6.1.4.1.9.9.97.1.2.8.1.1
An arbitrary integer which uniquely identifies the control query among all those specified for the switching engine indicated by entPhysicalIndex.
OBJECT-TYPE    
  Unsigned32  

cseFlowQueryMask 1.3.6.1.4.1.9.9.97.1.2.8.1.2
Setting each value causes the appropriate action: 'dstOnly' - causes the creation of rows in the cseFlowDataTable corresponding to the current L3 flow information for the absolute destination IP address set in the cseFlowQueryDestination object in this table. If cseFlowQueryDestinationMask is also specified at the same time, it will be applied to the address part of cseFlowQueryDestination. 'srcOrDst' - causes the creation of rows in the cseFlowDataTable corresponding to the current L3 flow information for EITHER of the absolute IP addresses set in the cseFlowQueryDestination or cseFlowQuerySource objects. If either of cseFlowQueryDestinationMask and cseFlowQuerySourceMask objects are also specified at the same time, they will be applied to the respective address parts of cseFlowQueryDestination and cseFlowQuerySource objects. This option is typically used to setup queries for flows on traffic in either directions. 'srcAndDst' - causes the creation of rows in the cseFlowDataTable corresponding to the current L3 flow information for BOTH the absolute IP addresses set in the cseFlowQueryDestination and cseFlowQuerySource objects. If either of cseFlowQueryDestinationMask and cseFlowQuerySourceMask objects are also specified at the same time, they will be applied to the respective address parts of cseFlowQueryDestination and cseFlowQuerySource objects. This option is typically used to setup queries for flows on traffic in one direction only. 'fullFlow' - causes the creation of row(s) in the cseFlowDataTable exactly corresponding to the current L3 flow information for the complete IP flow (including the transport port numbers) set in the cseFlowQueryDestination and cseFlowQuerySource objects. If either of cseFlowQueryDestinationMask and cseFlowQuerySourceMask objects are also specified at the same time, they will be applied to the respective address parts of cseFlowQueryDestination and cseFlowQuerySource objects. This option is typically used to setup queries for flows on traffic for specific (TCP/UDP) port numbers corresponding to standard protocols such as FTP, WWW, TELNET, etc. 'ipxDstOnly' - causes the creation of rows in the cseFlowDataTable corresponding to the current L3 flow information for the absolute destination IPX address set in the cseFlowQueryDestination object in this table. If cseFlowQueryDestinationMask is also specified at the same time, it will be applied to the address part of cseFlowQueryDestination. 'ipxSrcAndDst' - causes the creation of rows in the cseFlowDataTable corresponding to the current L3 flow information for BOTH the absolute IPX addresses set in the cseFlowQueryDestination and cseFlowQuerySource objects. If either of cseFlowQueryDestinationMask and cseFlowQuerySourceMask objects are also specified at the same time, they will be applied to the respective address parts of cseFlowQueryDestination and cseFlowQuerySource objects. 'any' - returns all rows corresponding to all established flow entries in the cseFlowDataTable. Note: 1. The type FlowAddressComponent used for objects cseFlowQuerySource and cseFlowQueryDestination, has the network address part and also the transport port number part, if applicable. 2. The value of this object cannot be modified when the corresponding instance of cseFlowQueryStatus is 'active'.
OBJECT-TYPE    
  INTEGER dstOnly(1), srcOrDst(2), srcAndDst(3), fullFlow(4), ipxDstOnly(5), ipxSrcAndDst(6), any(7)  

cseFlowQueryTransport 1.3.6.1.4.1.9.9.97.1.2.8.1.3
The IP transport protocol type specified for this query. Ignored for IPX flow queries. The value of this object cannot be modified when the corresponding instance of cseFlowQueryStatus is 'active'.
OBJECT-TYPE    
  BITS udp(0), tcp(1)  

cseFlowQuerySource 1.3.6.1.4.1.9.9.97.1.2.8.1.4
The source network address and port (if applicable). The value of this object cannot be modified when the corresponding instance of cseFlowQueryStatus is 'active'.
OBJECT-TYPE    
  FlowAddressComponent  

cseFlowQuerySourceMask 1.3.6.1.4.1.9.9.97.1.2.8.1.5
The source address mask to be applied to the corresponding instance of cseFlowQuerySource. The value of this object cannot be modified when the corresponding instance of cseFlowQueryStatus is 'active'.
OBJECT-TYPE    
  FlowAddressComponent  

cseFlowQueryDestination 1.3.6.1.4.1.9.9.97.1.2.8.1.6
The destination network address and port (if applicable). The value of this object cannot be modified when the corresponding instance of cseFlowQueryStatus is 'active'.
OBJECT-TYPE    
  FlowAddressComponent  

cseFlowQueryDestinationMask 1.3.6.1.4.1.9.9.97.1.2.8.1.7
The destination address mask to be applied to the corresponding instance of cseFlowQueryDestination. The value of this object cannot be modified when the corresponding instance of cseFlowQueryStatus is 'active'.
OBJECT-TYPE    
  FlowAddressComponent  

cseFlowQueryRouterIndex 1.3.6.1.4.1.9.9.97.1.2.8.1.8
Index of the router for which the flows are available. An 'all-zero' IP address indicates that the query is for any router. The value of this object cannot be modified when the corresponding instance of cseFlowQueryStatus is 'active'.
OBJECT-TYPE    
  IpAddress  

cseFlowQueryOwner 1.3.6.1.4.1.9.9.97.1.2.8.1.9
The manager entity that configured this entry and is therefore using the resources assigned to it.
OBJECT-TYPE    
  OwnerString  

cseFlowQueryResultingRows 1.3.6.1.4.1.9.9.97.1.2.8.1.10
The result status of the query. Possible values are: -1 - Either the query has not been initiated or the agent is busy processing this query instance. Time to completion of the query processing depends on the complexity of the query and the number of matches that satisfy this query. 0..2147483647 - The search has ended and this is the number of rows in the cseFlowDataTable, resulting from this query.
OBJECT-TYPE    
  Integer32 -1..2147483647  

cseFlowQueryResultTotalPkts 1.3.6.1.4.1.9.9.97.1.2.8.1.11
The aggregate number of total packets switched by the system on all the flows matching this query. This is a snapshot value and is valid only when the corresponding instance of cseFlowQueryResultingRows is greater than or equal to 0.
OBJECT-TYPE    
  CiscoGauge64  

cseFlowQueryResultTotalOctets 1.3.6.1.4.1.9.9.97.1.2.8.1.12
The aggregate number of total octets switched by the system on all the flows matching this query. This is a snapshot value and is valid only when the corresponding instance of cseFlowQueryResultingRows is greater than or equal to 0.
OBJECT-TYPE    
  CiscoGauge64  

cseFlowQueryResultAvgDuration 1.3.6.1.4.1.9.9.97.1.2.8.1.13
The average duration of the flows matching this query. This is a snapshot value and is valid only when the corresponding instance of cseFlowQueryResultingRows is greater than or equal to 0.
OBJECT-TYPE    
  TimeInterval  

cseFlowQueryResultAvgIdle 1.3.6.1.4.1.9.9.97.1.2.8.1.14
The elapsed time since the flows were last used, averaged over all flows matching this query. This is a snapshot value and is valid only when the corresponding instance of cseFlowQueryResultingRows is greater than or equal to 0.
OBJECT-TYPE    
  TimeInterval  

cseFlowQueryStatus 1.3.6.1.4.1.9.9.97.1.2.8.1.15
The status object used to manage rows in this table. When set to active(1), the query is initiated. Once initiated, the value may not be modified until the value of cseFlowQueryResultingRows is greater than or equal to 0. However, this object can be set to active(1) only after all the appropriate objects for this query as defined by the value set in the cseFlowQueryMask object, have also been set. Once a row becomes active, values within the row cannot be modified, except by deleting and re-creating it.
OBJECT-TYPE    
  RowStatus  

cseFlowQueryCreateTime 1.3.6.1.4.1.9.9.97.1.2.8.1.16
Time when this query was created.
OBJECT-TYPE    
  TimeStamp  

cseFlowQueryTotalFlows 1.3.6.1.4.1.9.9.97.1.2.8.1.17
The total number of L3 flows matching the query criterion.
OBJECT-TYPE    
  Unsigned32  

cseFlowQuerySkipNFlows 1.3.6.1.4.1.9.9.97.1.2.8.1.18
The number of searched flows to be skipped before storing any L3 flows in cseFlowDataTable. This object can be used along with cseFloQueryTotalFlows object to skip previously found flows by setting the variable equal to the number of the associated rows in cseFlowDataTable, and only query the remaining flows in the table. Note that due to the dynamical nature of the L3 flows, the queried flows may be missed or repeated by setting this object. The value of this object cannot be modified when the corresponding instance of cseFlowQueryStatus is 'active'.
OBJECT-TYPE    
  Integer32 0..2147483647  

cseFlowDataTable 1.3.6.1.4.1.9.9.97.1.2.9
A table containing L3 flow information corresponding to all the completed queries setup in the cseFlowQueryTable, that were initiated on the switch engine(s).
OBJECT-TYPE    
  SEQUENCE OF  
    CseFlowDataEntry

cseFlowDataEntry 1.3.6.1.4.1.9.9.97.1.2.9.1
A conceptual row of the cseFlowDataTable used to return information about one of the L3 flows which matched the search criteria set by the cseFlowQueryMask object in the corresponding instance of the cseFlowQueryTable.
OBJECT-TYPE    
  CseFlowDataEntry  

cseFlowDataIndex 1.3.6.1.4.1.9.9.97.1.2.9.1.1
A number to uniquely identify a result entry that matches a particular query for a specific switching engine.
OBJECT-TYPE    
  Unsigned32  

cseFlowDataSrcMac 1.3.6.1.4.1.9.9.97.1.2.9.1.2
Source Mac Address of the router's outgoing interface.
OBJECT-TYPE    
  MacAddress  

cseFlowDataDstMac 1.3.6.1.4.1.9.9.97.1.2.9.1.3
Destination Mac Address used to forward the packets in this flow.
OBJECT-TYPE    
  MacAddress  

cseFlowDataStaticFlow 1.3.6.1.4.1.9.9.97.1.2.9.1.4
Indicates whether this flow was software-installed.
OBJECT-TYPE    
  TruthValue  

cseFlowDataEncapType 1.3.6.1.4.1.9.9.97.1.2.9.1.5
Protocol encapsulation type used to forward packets in this flow to their destination.
OBJECT-TYPE    
  INTEGER ipArpa(1), ipxEthernet(2), ipx802raw(3), ipx802sap(4), ipx802snap(5), other(6)  

cseFlowDataSource 1.3.6.1.4.1.9.9.97.1.2.9.1.6
The source network address and the port (if appropriate) of this flow.
OBJECT-TYPE    
  FlowAddressComponent  

cseFlowDataDestination 1.3.6.1.4.1.9.9.97.1.2.9.1.7
The destination network address and port (if appropriate) of this flow.
OBJECT-TYPE    
  FlowAddressComponent  

cseFlowDataDestVlan 1.3.6.1.4.1.9.9.97.1.2.9.1.8
The vlan number on which packets belonging to this flow are forwarded.
OBJECT-TYPE    
  VlanIndex  

cseFlowDataIpQOS 1.3.6.1.4.1.9.9.97.1.2.9.1.9
Level of Quality of service for this IP flow. If it is not an IP flow, this object will not be instantiated.
OBJECT-TYPE    
  Integer32 0..7  

cseFlowDataIpQOSPolicy 1.3.6.1.4.1.9.9.97.1.2.9.1.10
Level of the Quality of service policy for this IP flow. If it is not an IP flow, this object will not be instantiated.
OBJECT-TYPE    
  Integer32 0..7  

cseFlowDataWhenCreated 1.3.6.1.4.1.9.9.97.1.2.9.1.11
Time when this flow was created in the switching engine.
OBJECT-TYPE    
  TimeStamp  

cseFlowDataLastUsed 1.3.6.1.4.1.9.9.97.1.2.9.1.12
Time since this flow was last used to forward a packet by the switching engine.
OBJECT-TYPE    
  TimeStamp  

cseFlowDataPkts 1.3.6.1.4.1.9.9.97.1.2.9.1.13
A snapshot value of the number of packets forwarded on this flow at the time of corresponding query.
OBJECT-TYPE    
  Gauge32  

cseFlowDataOctets 1.3.6.1.4.1.9.9.97.1.2.9.1.14
A snapshot value of octets forwarded on this flow at the time of corresponding query.
OBJECT-TYPE    
  CiscoGauge64  

cseFlowSwitchControlTable 1.3.6.1.4.1.9.9.97.1.2.10
A table used to control the L3 flow switching operation, per protocol type.
OBJECT-TYPE    
  SEQUENCE OF  
    CseFlowSwitchControlEntry

cseFlowSwitchControlEntry 1.3.6.1.4.1.9.9.97.1.2.10.1
A conceptual row for the configuration of Flow switching feature for an L3 protocol type.
OBJECT-TYPE    
  CseFlowSwitchControlEntry  

cseFlowSwitchProtocol 1.3.6.1.4.1.9.9.97.1.2.10.1.1
Protocol type for which this row instance. Only ip(1) and ipx(14) values are currently supported.
OBJECT-TYPE    
  CiscoNetworkProtocol  

cseFlowSwitchStatus 1.3.6.1.4.1.9.9.97.1.2.10.1.2
The current status of the global flow switching capability for the specified L3 protocol type.
OBJECT-TYPE    
  ControlStatus  

cseFlowMcastMaxQueries 1.3.6.1.4.1.9.9.97.1.2.11
Maximum number of query entries allowed to be outstanding at any time, in the cseFlowMcastQueryTable. The typical value for this object is 5.
OBJECT-TYPE    
  Unsigned32  

cseFlowMcastQueryTable 1.3.6.1.4.1.9.9.97.1.2.12
A control table used to query the switching engine by specifying retrieval criteria for IP multicast L3 flows. Each row instance in the table represents a query with its parameters. The resulting data for each instance of a query in this table is returned in the cseFlowMcastResultTable. The maximum number of entries (rows) in this table cannot exceed the value of cseFlowMcastMaxQueries object. Unlike unicast switched layer 3 flows, an IP multicast switched flow is created and installed by software, and is uniquely identified by flow's source IP address, and multicast group IP address. It is stored with input Vlan ID in the cache entry, so that the packets in the flow will not be replicated and forwarded to the receivers on the same (input) Vlan. Another difference is that all IP multicast hardware switched flows belonging to the same (source, group) are stored only on one switch engine on a Cisco L3 switch with distributed switch engines, whereas unicast flows identified by certain criterion may resident on multiple switch engines in the system.
OBJECT-TYPE    
  SEQUENCE OF  
    CseFlowMcastQueryEntry

cseFlowMcastQueryEntry 1.3.6.1.4.1.9.9.97.1.2.12.1
A conceptual row of the cesMcastFlowQueryTable used to setup retrieval criteria to search for IP multicast L3 flows on all switching engine entities in the device. The actual search is started by setting the value of cseFlowMcastQueryStatus to 'active'. Once a row becomes active, values within the row cannot be modified, without setting the associated RowStatus object to 'notInService' first, or deleting and re-creating the row.
OBJECT-TYPE    
  CseFlowMcastQueryEntry  

cseFlowMcastQueryIndex 1.3.6.1.4.1.9.9.97.1.2.12.1.1
An arbitrary integer in the range of 1 to cseFlowMcastMaxQueries to identify this control query.
OBJECT-TYPE    
  Unsigned32  

cseFlowMcastQueryMask 1.3.6.1.4.1.9.9.97.1.2.12.1.2
This object is used to set up the query criterion for the multicast flows of interest. If any one of the defined BITs is set, then the value of the corresponding object in the same row instance will be used for the search. Specifically, if the 'source(0)' BIT is set, then the cseFlowMcastQuerySrc object will be included in the search criterion. If the group(1) BIT is set, then the cseFlowMcastQueryGrp object will be included in the search criterion. If the vlan(2) BIT is set, then the cseFlowMcastQuerySrcVlan object will be included in the search criterion. If the router(3) BIT is set, then the cseFlowMcastQueryRtrIndex object will be included in the search criterion. If the mvrf(4) BIT is set, then the cseFlowMcastQueryMvrf object will be included in the search criterion; If the sourceip(5) BIT is set, then the cseFlowMcastQueryAddrType and cseFlowMcastQuerySource objects will be included in the search criterion. If the groupip(6) BIT is set, then the cseFlowMcastQueryAddrType and cseFlowMcastQueryGroup objects will be included in the search criterion. If the source(0) or group(1) BIT is set, then the sourceip(5) or groupip(6) cannot be set, and vice-versa. If any of the BITs in this variable is cleared, the corresponding parameter object in the same row is treated as a wildcard. When the row is instantiated, the BITs in the variable will be cleared, and none of query parameter objects in this row will be instantiated. This will be considered as a wildcard search for flows on the default Multicast Virtual Private Network (MVPN) routing/forwarding (MVRF) instance. i.e. it will return all rows corresponding to all established multicast flow entries in the default MVRF, in cseFlowMcastResultTable. The address type of this wildcard search will be specified be cseFlowMcastQueryAddrType. It is SNMP managers' responsibility to set certain bits on in this object instance, if necessary, and the corresponding flow parameter variables to the appropriate values in order to setup the desired query criteria. The value of this object can not be altered when the corresponding instance of cseFlowMcastQueryStatus is 'active'.
OBJECT-TYPE    
  BITS source(0), group(1), vlan(2), router(3), mvrf(4), sourceip(5), groupip(6)  

cseFlowMcastQuerySrc 1.3.6.1.4.1.9.9.97.1.2.12.1.3
The source address of the IP multicast layer 3 flows. This object should be instantiated and assigned a proper IP address whenever the 'source' bit of cseFlowMcastQueryMask object in the same row is on. If the 'source' bit is set, and an appropriate IP address is assigned to this object, then only flows with the specified source address will be containing in the result table. If the 'source' bit in the associated cseFlowMcastQueryMask is cleared, this object is ignored during the query, and all flows will be considered regardless of their source IP address. This object is deprecated and replaced by cseFlowMcastQueryAddrType and cseFlowMcastQuerySource.
OBJECT-TYPE    
  IpAddress  

cseFlowMcastQueryGrp 1.3.6.1.4.1.9.9.97.1.2.12.1.4
The IP multicast group address of the queried flows. This object should be instantiated and set whenever the 'group' bit of the associated cseFlowMcastQueryMask object is on. If the 'group' bit is set, and a multicast group address is assigned to the object, only flows with the specified group address will be contained in the result table. If the 'group' bit in the associated cseFlowMcastQueryMask is cleared, this object is ignored during the query, and all flows will be considered regardless of their group address. This object is deprecated and replaced by cseFlowMcastQueryAddrType and cseFlowMcastQueryGroup.
OBJECT-TYPE    
  McastGroupIp  

cseFlowMcastQuerySrcVlan 1.3.6.1.4.1.9.9.97.1.2.12.1.5
The source Vlan ID of the IP multicast layer 3 flows. This object should be instantiated and set whenever the 'vlan' bit of the associated cseFlowMcastQueryMask object is on. If the 'vlan' bit is set, and a Vlan ID is assigned to this object, only flows belonging to that vlan will be contained in the result table. If the 'vlan' bit in the associated cseFlowMcastQueryMask object is cleared, this object is ignored during the query, and all flows will be considered regardless of their vlan IDs.
OBJECT-TYPE    
  VlanIndex  

cseFlowMcastQueryRtrIndex 1.3.6.1.4.1.9.9.97.1.2.12.1.6
Index of the router for which the multicast flows are available, that is the flows would be replicated and routed by the specified router, should the flows did not get switched. This object should be instantiated and set whenever the 'router' bit of the asociated cseFlowMcastQueryMask object is on. If the 'router' bit is set, and a router's IP address is assigned to this object, then only flows associated with that router will be contained in the result table. If the 'router' bit in the cseFlowMcastQueryMask object is cleared, this object is ignored during the query, and all flows will be considered regardless of the routers being switched.
OBJECT-TYPE    
  IpAddress  

cseFlowMcastQuerySkipNFlows 1.3.6.1.4.1.9.9.97.1.2.12.1.7
The number of searched flows to be skipped before storing any multicast flows in cseFlowMcastResultTable. This object can be used along with cseFlowMcastQueryTotalFlows object to skip previously found flows by setting the variable equal to the number of the associated rows in cseFlowMcastResultTable, and only query the remaining flows in the table. Note that due to the dynamical nature of the L3 flows, the queried flows may be missed or repeated by setting this object.
OBJECT-TYPE    
  Integer32 0..2147483647  

cseFlowMcastQueryOwner 1.3.6.1.4.1.9.9.97.1.2.12.1.8
The manager entity that configured this entry and is therefore using the resources assigned to it. It is used to model an administratively assigned name of the owner of a resource. It is recommended that this object have one or more the following information: IP address, management station name, network manager's name, location, or phone number.
OBJECT-TYPE    
  OwnerString  

cseFlowMcastQueryTotalFlows 1.3.6.1.4.1.9.9.97.1.2.12.1.9
The number of flows matching the query criterion.
OBJECT-TYPE    
  Integer32 0..2147483647  

cseFlowMcastQueryRows 1.3.6.1.4.1.9.9.97.1.2.12.1.10
Indicating the status of the query by following values: -1 - Either the query has not been started or the agent is still processing this query instance. It is the default value when the row is instantiated. 0..2147483647 - The search has ended and this is the number of rows in the cseFlowMcastResultTable, resulting from this query.
OBJECT-TYPE    
  Integer32 -1..2147483647  

cseFlowMcastQueryStatus 1.3.6.1.4.1.9.9.97.1.2.12.1.11
The status object used to manage rows in this table. When set to 'active', the query of flows is initiated. This object can be set to active only after all the appropriate objects for this query as defined by the bits in the cseFlowMcastQueryMask object, have also been instantiated. The completion of the query is indicated by the value of cseFlowMcastQueryRows as soon as it becomes greater than or equal to 0. Once a row becomes active, values within the row cannot be modified without setting it to 'notInService' first, or just deleting and re-creating it. To abort a lengthy on-going query, setting this object to 'notInService', or 'destroy' will terminate a search if one is in progress, and cause the associated rows in cseFlowMcastResultTable, if any, to be deleted.
OBJECT-TYPE    
  RowStatus  

cseFlowMcastQueryCreateTime 1.3.6.1.4.1.9.9.97.1.2.12.1.12
Time when this query was last set to active.
OBJECT-TYPE    
  TimeStamp  

cseFlowMcastQueryMvrf 1.3.6.1.4.1.9.9.97.1.2.12.1.13
The human-readable name of the Multicast Virtual Private Network (MVPN) routing/forwarding instance (MVRF). When the 'mvrf' bit of cseFlowMcastQueryMask object in the same row is on, an appropriate value should be specified and only flows with the specified MVRF name will be contained in the result table. If the 'mvrf' bit in the associated cseFlowMcastQueryMask is cleared, this object is ignored during the query, and all the flows corresponding to the default MVRF will be considered.
OBJECT-TYPE    
  MplsVpnId  

cseFlowMcastQueryAddrType 1.3.6.1.4.1.9.9.97.1.2.12.1.14
The Internet address type for this multicast search query.
OBJECT-TYPE    
  InetAddressType  

cseFlowMcastQuerySource 1.3.6.1.4.1.9.9.97.1.2.12.1.15
The source Internet address of the IP multicast layer 3 flows. When the 'sourceip' bit of cseFlowMcastQueryMask cseFlowMcastQueryMask object in the same row is on, an appropriate value should be specified and only flows with the specified source address will be contained in the result table. If the 'sourceip' bit in the associated cseFlowMcastQueryMask is cleared, this object is ignored during the query, and all flows will be considered regardless of their source address. The type of this address is determined by the value of the cseFlowMcastQueryAddrType object. The default value of this object is all zeros.
OBJECT-TYPE    
  InetAddress  

cseFlowMcastQueryGroup 1.3.6.1.4.1.9.9.97.1.2.12.1.16
The multicast group Internet address of the queried flows. When the 'mvrf' bit of cseFlowMcastQueryMask object in the same row is on, an appropriate value should be specified and only flows with the specified group address will be contained in the result table. If the 'groupip' bit in the associated cseFlowMcastQueryMask is cleared, this object is ignored during the query, and all flows will be considered regardless of their group address. The type of this address is determined by the value of the cseFlowMcastQueryAddrType object. The default value of this object is all zeros.
OBJECT-TYPE    
  InetAddress  

cseFlowMcastResultTable 1.3.6.1.4.1.9.9.97.1.2.13
A table containing current IP multicast flow information corresponding to all the completed queries set up in the cseFlowMcastQueryTable, that were initiated on the switch engine(s). The query result will not become available until the current search completes.
OBJECT-TYPE    
  SEQUENCE OF  
    CseFlowMcastResultEntry

cseFlowMcastResultEntry 1.3.6.1.4.1.9.9.97.1.2.13.1
A conceptual row of cseFlowMcastResultTable, containing information about an IP multicast layer 3 flow that matchs the search criteria set in the corresponding row of cseFlowMcastQueryTable. This row instance is indexed by the query index (cseFlowMcastQueryIndex), the switch engine entity (entPhysicalIndex), and data entry index (cseFlowMcastResultIndex). The value of entPhysicalIndex object is assigned by Entity-MIB, and uniquely identifies a switching engine on which the IP multicast flow is stored.
OBJECT-TYPE    
  CseFlowMcastResultEntry  

cseFlowMcastResultIndex 1.3.6.1.4.1.9.9.97.1.2.13.1.1
A positive integer which uniquely identify a result entry on a specific switching engine matching a particular query.
OBJECT-TYPE    
  Integer32 1..2147483647  

cseFlowMcastResultGrp 1.3.6.1.4.1.9.9.97.1.2.13.1.2
The multicast group IP address of the multicast layer 3 flow. This object is deprecated and replaced by cseFlowMcastResultAddrType and cseFlowMcastResultGroup.
OBJECT-TYPE    
  McastGroupIp  

cseFlowMcastResultSrc 1.3.6.1.4.1.9.9.97.1.2.13.1.3
The source address of the multicast layer 3 flow. This object is deprecated and replaced by cseFlowMcastResultAddrType and cseFlowMcastResultSource.
OBJECT-TYPE    
  IpAddress  

cseFlowMcastResultSrcVlan 1.3.6.1.4.1.9.9.97.1.2.13.1.4
The source Vlan ID of the IP multicast layer 3 flow.
OBJECT-TYPE    
  VlanIndex  

cseFlowMcastResultRtrIp 1.3.6.1.4.1.9.9.97.1.2.13.1.5
The interface IP address of the router this multicast flow is switching for. Since IP multicast flows can only be established for a router's trunk ports, it is the primary IP address of the router's trunk link that connects to the switch.
OBJECT-TYPE    
  IpAddress  

cseFlowMcastResultRtrMac 1.3.6.1.4.1.9.9.97.1.2.13.1.6
The default MAC address of the router the multicast flow is switching for. Different multicast flows switching different ports of the same router will have the identical value of this object.
OBJECT-TYPE    
  MacAddress  

cseFlowMcastResultCreatedTS 1.3.6.1.4.1.9.9.97.1.2.13.1.7
Time when the IP multicast flow was created.
OBJECT-TYPE    
  TimeStamp  

cseFlowMcastResultLastUsedTS 1.3.6.1.4.1.9.9.97.1.2.13.1.8
Time when this IP multicast flow was last used.
OBJECT-TYPE    
  TimeStamp  

cseFlowMcastResultPkts 1.3.6.1.4.1.9.9.97.1.2.13.1.9
The total number of multicast traffic packets forwarded for this flow (replicated packets are not counted).
OBJECT-TYPE    
  Counter64  

cseFlowMcastResultOctets 1.3.6.1.4.1.9.9.97.1.2.13.1.10
The total number of multicast traffic octets forwarded for this flow (replicated packets are not counted).
OBJECT-TYPE    
  Counter64  

cseFlowMcastResultDstVlans 1.3.6.1.4.1.9.9.97.1.2.13.1.11
A string of octets containing one bit per VLAN. Each octet within the value of this object specifies a set of eight VLANs, e.g. the first octet corresponding to VLANs with VlanIndex values of 0 through 7, the second octet to VLANs 8 through 15, etc. Within each octet, the most significant bit represents the lowest numbered VLAN, and the least significant bit represents the highest numbered VLAN, thus each vlan is represented by a single bit within the octet. The bits in this object will be set to '1' if the corresponding Vlans are in the out-going interface (vlan) list of the IP multicast flow described by this row instance.
OBJECT-TYPE    
  OCTET STRING SIZE(0..128)  

cseFlowMcastResultDstVlans2k 1.3.6.1.4.1.9.9.97.1.2.13.1.12
A string of octets containing one bit per VLAN, with VlanIndex values of 1024 through 2047,with each octet within the value of this object specifies a set of eight VLANs, e.g. the first octet corresponding to VLANs with VlanIndex values of 1024 through 1031, the second octet to VLANs 1032 through 1039 etc. Within each octet, the most significant bit represents the lowest numbered VLAN, and the least significant bit represents the highest numbered VLAN, thus each vlan is represented by a single bit within the octet. The bits in this object will be set to '1' if the corresponding Vlans are in the out-going interface (vlan) list of the IP multicast flow described by this row instance.
OBJECT-TYPE    
  OCTET STRING SIZE(0..128)  

cseFlowMcastResultDstVlans3k 1.3.6.1.4.1.9.9.97.1.2.13.1.13
A string of octets containing one bit per VLAN. With VlanIndex values of 2048 through 3071 with each octet within the value of this object specifies a set of eight VLANs, e.g. the first octet corresponding to VLANs with VlanIndex values of 2048 through 2055, the second octet to VLANs 2056 through 2063 etc. Within each octet, the most significant bit represents the lowest numbered VLAN, and the least significant bit represents the highest numbered VLAN, thus each vlan is represented by a single bit within the octet. The bits in this object will be set to '1' if the corresponding Vlans are in the out-going interface (vlan) list of the IP multicast flow described by this row instance.
OBJECT-TYPE    
  OCTET STRING SIZE(0..128)  

cseFlowMcastResultDstVlans4k 1.3.6.1.4.1.9.9.97.1.2.13.1.14
A string of octets containing one bit per VLAN. With VlanIndex values of 3072 through 4095, with each octet within the value of this object specifies a set of eight VLANs, e.g. the first octet corresponding to VLANs with VlanIndex values of 3072 through 3079 the second octet to VLANs 3080 through 3087 etc. Within each octet, the most significant bit represents the lowest numbered VLAN, and the least significant bit represents the highest numbered VLAN, thus each vlan is represented by a single bit within the octet. The bits in this object will be set to '1' if the corresponding Vlans are in the out-going interface (vlan) list of the IP multicast flow described by this row instance.
OBJECT-TYPE    
  OCTET STRING SIZE(0..128)  

cseFlowMcastResultMvrf 1.3.6.1.4.1.9.9.97.1.2.13.1.15
The MVRF to which this flow belongs to.
OBJECT-TYPE    
  MplsVpnId  

cseFlowMcastResultAddrType 1.3.6.1.4.1.9.9.97.1.2.13.1.16
The Internet address type of cseFlowMcastResultGroup and cseFlowMcastResultSource.
OBJECT-TYPE    
  InetAddressType  

cseFlowMcastResultGroup 1.3.6.1.4.1.9.9.97.1.2.13.1.17
The multicast group IP address of the multicast layer 3 flow.
OBJECT-TYPE    
  InetAddress  

cseFlowMcastResultSource 1.3.6.1.4.1.9.9.97.1.2.13.1.18
The source address of the multicast layer 3 flow.
OBJECT-TYPE    
  InetAddress  

cseFlowMcastResultFlowType 1.3.6.1.4.1.9.9.97.1.2.13.1.19
Indicates the type of multicast layer 3 flow. other - Multicast flow type is none of the followoing. rpfMfd - This flow is a RPF MFD flow. partial - This flow is a partial shortcut flow.
OBJECT-TYPE    
  INTEGER other(1), rpfMfd(2), partialSC(3)  

cseFlowMcastResultHFlag1k2k 1.3.6.1.4.1.9.9.97.1.2.13.1.20
A string of octets containing one bit per out-going interface (VLAN) with VlanIndex values of 0 through 2047. Each octet within the value of this object specifies a set of eight VLANs, e.g. the first octet corresponding to VLANs with VlanIndex values of 0 through 7, the second octet to VLANs 8 through 15, etc. Within each octet, the most significant bit represents the lowest numbered VLAN, and the least significant bit represents the highest numbered VLAN, thus each vlan is represented by a single bit within the octet. The bits in this object will be set to '1' if the multicast layer 3 flow described by this row instance is hardware switched on the corresponding VLAN. If the length of this string is less than 256 octets, any 'missing' octets are assumed to contain the value of zero.
OBJECT-TYPE    
  OCTET STRING SIZE(0..256)  

cseFlowMcastResultHFlag3k4k 1.3.6.1.4.1.9.9.97.1.2.13.1.21
A string of octets containing one bit per out-going interface (VLAN) with VlanIndex values of 2048 through 4095. Each octet within the value of this object specifies a set of eight VLANs, e.g. the first octet corresponding to VLANs with VlanIndex values of 2048 through 2055, the second octet to VLANs 2056 through 2063 etc. Within each octet, the most significant bit represents the lowest numbered VLAN, and the least significant bit represents the highest numbered VLAN, thus each vlan is represented by a single bit within the octet. The bits in this object will be set to '1' if the multicast layer 3 flow described by this row instance is hardware switched on the corresponding VLAN. If the length of this string is less than 256 octets, any 'missing' octets are assumed to contain the value of zero.
OBJECT-TYPE    
  OCTET STRING SIZE(0..256)  

cseFlowMcastSwitchStatus 1.3.6.1.4.1.9.9.97.1.2.14
The current status of the global IP multicast flow switching capability. When enabled, the switch engine will be able to install multicast flow entries in its L3 forwarding table, and perform hardware assisted switching for the flows.
OBJECT-TYPE    
  ControlStatus  

cseFlowIPXEstablishedAgingTime 1.3.6.1.4.1.9.9.97.1.2.15
The administrative aging time for established IPX flows. The default value for this object is implementation specific. The corresponding operational object is cseFlowOperIPXAgingTime.
OBJECT-TYPE    
  Integer32 1..2147483647  

cseStaticIpxExtRouterTable 1.3.6.1.4.1.9.9.97.1.2.16
A table of external routers which are enabled for Layer 3 IPX switching by the switching engine. This table may contain routers that have not yet been discovered by the device.
OBJECT-TYPE    
  SEQUENCE OF  
    CseStaticIpxExtRouterEntry

cseStaticIpxExtRouterEntry 1.3.6.1.4.1.9.9.97.1.2.16.1
A conceptual row in the cseStaticIpxExtRouterTable for enabling an external router to be installed in the switch's router table. The entry is created and deleted by using cseStaticIpxRouterStatus.
OBJECT-TYPE    
  CseStaticIpxExtRouterEntry  

cseStaticIpxRouterName 1.3.6.1.4.1.9.9.97.1.2.16.1.1
DNS name (if available) of the external router.
OBJECT-TYPE    
  DisplayString  

cseStaticIpxRouterOwner 1.3.6.1.4.1.9.9.97.1.2.16.1.2
String indicating the owner who created the static entry.
OBJECT-TYPE    
  OwnerString  

cseStaticIpxRouterStatus 1.3.6.1.4.1.9.9.97.1.2.16.1.3
Used to manage creation and deletion of rows in this table. Once a row becomes active, values within that row cannot be modified except by deleting and creating the row.
OBJECT-TYPE    
  RowStatus  

cseFlowOperEstablishedAgingTime 1.3.6.1.4.1.9.9.97.1.2.17
The operational aging time for IP established flows.
OBJECT-TYPE    
  Integer32 1..2147483647  

cseFlowOperFastAgingTime 1.3.6.1.4.1.9.9.97.1.2.18
The operational fast aging time for the established flow entries, that have less number of packets than the value set in the cseFlowOperFastAgePktThreshold,switched within this time.
OBJECT-TYPE    
  Unsigned32  

cseFlowOperFastAgePktThreshold 1.3.6.1.4.1.9.9.97.1.2.19
The operational packet threshold for the cseFlowOperFastAgingTime.
OBJECT-TYPE    
  Unsigned32  

cseFlowOperIPXAgingTime 1.3.6.1.4.1.9.9.97.1.2.20
The operational aging time for established IPX flows.
OBJECT-TYPE    
  Integer32 1..2147483647  

cseBridgedFlowStatsCtrlTable 1.3.6.1.4.1.9.9.97.1.2.21
A table controls the reporting of intra-vlan statistics for bridged flow per vlan. When a vlan is created in a device supporting this table, a corresponding entry of this table will be added.
OBJECT-TYPE    
  SEQUENCE OF  
    CseBridgedFlowStatsCtrlEntry

cseBridgedFlowStatsCtrlEntry 1.3.6.1.4.1.9.9.97.1.2.21.1
A row instance contains the configuration to enable or disable the reporting of intra-vlan statistics for bridged flow per vlan.
OBJECT-TYPE    
  CseBridgedFlowStatsCtrlEntry  

cseBridgedFlowVlan 1.3.6.1.4.1.9.9.97.1.2.21.1.1
Indicates the Vlan number on which the reporting of intra-vlan bridged flow statistics is configured.
OBJECT-TYPE    
  VlanIndex  

cseFlowBridgedFlowStatsEnable 1.3.6.1.4.1.9.9.97.1.2.21.1.2
Indicates whether intra-vlan bridged flow statistics is enabled. If this object is set to 'true', intra-vlan bridged flow statistics is reported in cseFlowDataTable when a corresponding query is set up in cseFlowQueryTable. If this object is set to 'false', intra-vlan bridged flow statistics is not reported. The default is false.
OBJECT-TYPE    
  TruthValue  

cseFlowIPFlowMask 1.3.6.1.4.1.9.9.97.1.2.22
Indicates the flow mask for IP flows. If dstOnly(1) is used, it enables flows based on Layer 3 destination addresses only. If srcDst(2) is used, it enables flows based on both Layer 3 source and destination addresses only. If fullFlow(3) is used, it enables flows based on Layer 4 port numbers in addition to source and destination addresses. If srcOnly(4) is used, it enables flows based on Layer 3 source addresses only. If intDstSrc(5) is used, it enables flows based on source interface in addition to source and destination addresses. If intFull(6) is used, it enables flows based on source interface in addition to Layer 4 port numbers, source and destination addresses. If null(7) is used, no flow will be enabled. If intDstOnly(8) is used, it enables flows based on source interface in addition to the destination addresses. If intSrcOnly(9) is used, it enables flows based on source interface in addition to the source addresses.
OBJECT-TYPE    
  INTEGER dstOnly(1), srcDst(2), fullFlow(3), srcOnly(4), intDstSrc(5), intFull(6), null(7), intDstOnly(8), intSrcOnly(9)  

cseFlowIPXFlowMask 1.3.6.1.4.1.9.9.97.1.2.23
Indicates the flow mask for IPX flows. If dstOnly(1) is used, it enables flows based on Layer 3 destination addresses only. If srcDst(2) is used, it enables flows based on both Layer 3 source and destination addresses only.
OBJECT-TYPE    
  INTEGER dstOnly(1), srcDst(2)  

cseFlowLongAgingTime 1.3.6.1.4.1.9.9.97.1.2.24
The administrative long aging time for the established flow entries. Setting to value of 0 turns off long aging.
OBJECT-TYPE    
  Unsigned32  

cseFlowExcludeTable 1.3.6.1.4.1.9.9.97.1.2.25
A table controls the flow creation based on protocol and port number. If a packet matches the protocol and port number specified in this table entries, a flow entry will not be established.
OBJECT-TYPE    
  SEQUENCE OF  
    CseFlowExcludeEntry

cseFlowExcludeEntry 1.3.6.1.4.1.9.9.97.1.2.25.1
A row instance contains the configuration to enable or disable the establishment of flow entry for matching traffic.
OBJECT-TYPE    
  CseFlowExcludeEntry  

cseFlowExcludePort 1.3.6.1.4.1.9.9.97.1.2.25.1.1
Indicates the TCP or UDP port number that matching traffic will be excluded from flow establishment. The value of 0 is not allowed.
OBJECT-TYPE    
  CiscoPort  

cseFlowExcludeProtocol 1.3.6.1.4.1.9.9.97.1.2.25.1.2
Indicates the protocol that matching traffic will be excluded from flow establishment.
OBJECT-TYPE    
  INTEGER udp(1), tcp(2), both(3)  

cseFlowExcludeStatus 1.3.6.1.4.1.9.9.97.1.2.25.1.3
The status of this conceptual row. New rows are created using 'createAndGo' and deleted using 'destroy'. Once 'active' this object may be set to only 'destroy'. cseFlowExcludeProtocol may be modified at any time (even while the row is active).
OBJECT-TYPE    
  RowStatus  

cseFlowStatsTable 1.3.6.1.4.1.9.9.97.1.2.26
A table containing flow statistics information on each switching engine.
OBJECT-TYPE    
  SEQUENCE OF  
    CseFlowStatsEntry

cseFlowStatsEntry 1.3.6.1.4.1.9.9.97.1.2.26.1
A conceptual row of cseFlowStatsTable, containing flow statistics maintained by a switching engine entity (identified by entPhysicalIndex). Each switching engine managed by this MIB module has an entry in this table.
OBJECT-TYPE    
  CseFlowStatsEntry  

cseFlowTotalFlows 1.3.6.1.4.1.9.9.97.1.2.26.1.1
Indicates the total number of flow entries installed in this switching engine.
OBJECT-TYPE    
  Gauge32  

cseNetflowLS 1.3.6.1.4.1.9.9.97.1.3
OBJECT IDENTIFIER    

cseNetflowLSExportStatus 1.3.6.1.4.1.9.9.97.1.3.1
Status of the Netflow LAN Switching data export feature.
OBJECT-TYPE    
  ControlStatus  

cseNetflowLSExportHost 1.3.6.1.4.1.9.9.97.1.3.2
Network(IP) address in dotted decimal format or the DNS hostname of the host to which Netflow LAN switching statistics are exported.
OBJECT-TYPE    
  DisplayString  

cseNetflowLSExportTransportNumber 1.3.6.1.4.1.9.9.97.1.3.3
The transport(UDP) port number to be used for the Netflow LAN switching statistics being exported.
OBJECT-TYPE    
  Unsigned32  

cseNetflowLSExportDataSource 1.3.6.1.4.1.9.9.97.1.3.4
The source network address used as a filter for selecting the flows to which the netflow LAN switching data export feature is applied.
OBJECT-TYPE    
  FlowAddressComponent  

cseNetflowLSExportDataSourceMask 1.3.6.1.4.1.9.9.97.1.3.5
The mask to be applied to the corresponding instance of cseNetflowExportDataSource.
OBJECT-TYPE    
  FlowAddressComponent  

cseNetflowLSExportDataDest 1.3.6.1.4.1.9.9.97.1.3.6
The destination network address used as a filter for selecting the flows to which the netflow LAN switching data export feature is applied.
OBJECT-TYPE    
  FlowAddressComponent  

cseNetflowLSExportDataDestMask 1.3.6.1.4.1.9.9.97.1.3.7
The mask to be applied to its corresponding instance of cseNetflowExportDataDest.
OBJECT-TYPE    
  FlowAddressComponent  

cseNetflowLSExportDataProtocol 1.3.6.1.4.1.9.9.97.1.3.8
The protocol used as a filter for selecting the flows to which the netflow LAN switching data export feature is applied.
OBJECT-TYPE    
  Integer32 0..255  

cseNetflowLSExportDataFilterSelection 1.3.6.1.4.1.9.9.97.1.3.9
The filter set can be chosen either included(1) or excluded(2) mutually exclusive. If this object is set to included(1) - exports the flows that match cseNetflowLSExportDataSource, cseNetflowLSExportDataSourceMask, cseNetflowLSExportDataDest, cseNetflowLSExportDataDestMask and cseNetflowLSExportDataProtocol. excluded(2) - exports the flows that don't match cseNetflowLSExportDataSource, cseNetflowLSExportDataSourceMask, cseNetflowLSExportDataDest, cseNetflowLSExportDataDestMask and cseNetflowLSExportDataProtocol.
OBJECT-TYPE    
  INTEGER included(1), excluded(2)  

cseNetflowLSExportNDEVersionNumber 1.3.6.1.4.1.9.9.97.1.3.10
The netflow data export version number which is supported by the device. The typical value of this object can be 1, 7 or 8.
OBJECT-TYPE    
  Integer32 1..65535  

cseNetflowLSFilterSupport 1.3.6.1.4.1.9.9.97.1.3.11
Indicates whether this device supports single filter or multiple filters. single - use objects in cseNDESingleFilterGroupRev1 to configure NDE filtering paramaters. multiple - use objects in cseNDEMultipleFiltersGroup to configure NDE filtering paramaters.
OBJECT-TYPE    
  INTEGER single(1), multiple(2)  

cseNetflowLSFilterTable 1.3.6.1.4.1.9.9.97.1.3.12
A Table containing Netflow Data Export filtering configuration.
OBJECT-TYPE    
  SEQUENCE OF  
    CseNetflowLSFilterEntry

cseNetflowLSFilterEntry 1.3.6.1.4.1.9.9.97.1.3.12.1
A conceptutal row in the cseNetflowLSFilterTable, representing a NDE filter configuration.
OBJECT-TYPE    
  CseNetflowLSFilterEntry  

cseNetflowLSFilterIndex 1.3.6.1.4.1.9.9.97.1.3.12.1.1
An arbitrary integer which uniquely identifies the filter
OBJECT-TYPE    
  Unsigned32  

cseNetflowLSFilterDataSource 1.3.6.1.4.1.9.9.97.1.3.12.1.2
The source network address used as a filter for selecting the flows to which the netflow LAN switching data export feature is applied. If cseNetflowLSNDEFilterDataSource contains all zeros, then the cseNetflowLSNDEFilterDataSource object will not be included in the filtering criterion.
OBJECT-TYPE    
  FlowAddressComponent  

cseNetflowLSFilterDataSourceMask 1.3.6.1.4.1.9.9.97.1.3.12.1.3
The mask to be applied to the corresponding instance of cseNetflowExportDataSource. If cseNetflowLSFilterDataSourceMask contains all zeros, then the cseNetflowLSFilterDataSourceMask object will not be included in the filtering criterion.
OBJECT-TYPE    
  FlowAddressComponent  

cseNetflowLSFilterDataDest 1.3.6.1.4.1.9.9.97.1.3.12.1.4
The destination network address used as a filter for selecting the flows to which the netflow LAN switching data export feature is applied. If cseNetflowLSFilterDataDest contains all zeros, then the cseNetflowLSFilterDataDest object will not be included in the filtering criterion.
OBJECT-TYPE    
  FlowAddressComponent  

cseNetflowLSFilterDataDestMask 1.3.6.1.4.1.9.9.97.1.3.12.1.5
The mask to be applied to its corresponding instance of cseNetflowExportDataDest. If cseNetflowLSFilterDataDestMask contains all zeros, then the cseNetflowLSFilterDataDestMask object will not be included in the filtering criterion.
OBJECT-TYPE    
  FlowAddressComponent  

cseNetflowLSFilterDataProtocol 1.3.6.1.4.1.9.9.97.1.3.12.1.6
The protocol used as a filter for selecting the flows to which the netflow LAN switching data export feature is applied. The default value is set to 0, to specify that no value has been set. If cseNetflowLSFilterDataProtocol is set to 0, then the cseNetflowLSFilterDataProtocol object will not be included in the filtering criterion.
OBJECT-TYPE    
  Integer32 0..255  

cseNetflowLSFilterSelection 1.3.6.1.4.1.9.9.97.1.3.12.1.7
The filter set can be chosen either included(1) or excluded(2). If this object is set to included(1) - exports the flows that match cseNetflowLSFilterDataSource, cseNetflowLSFilterDataSourceMask, cseNetflowLSFilterDataDest, cseNetflowLSFilterDataDestMask and cseNetflowLSFilterDataProtocol. excluded(2) - exports the flows that don't match cseNetflowLSFilterDataSource, cseNetflowLSFilterDataSourceMask, cseNetflowLSFilterDataDest, cseNetflowLSFilterDataDestMask and cseNetflowLSFilterDataProtocol.
OBJECT-TYPE    
  INTEGER included(1), excluded(2)  

cseNetflowLSFilterStatus 1.3.6.1.4.1.9.9.97.1.3.12.1.8
The status object used to manage the rows in this table. Once a row becomes active, values within that row cannot be modified except by deleting and creating the row.
OBJECT-TYPE    
  RowStatus  

cseNetFlowIfIndexEnable 1.3.6.1.4.1.9.9.97.1.3.13
Indicates whether ifIndex reporting in NDE (Netflow Data Export) is enabled. if bit destIfIndex(0) is on, destination ifIndex reporting in NDE is enabled. if bit srcIfIndex(1) is on, source ifIndex reporting in NDE is enabled.
OBJECT-TYPE    
  BITS destIfIndex(0), srcIfIndex(1)  

cseNetflowASInfoExportCtrl 1.3.6.1.4.1.9.9.97.1.3.14
Indicates whether export of Autonomous System(AS) number information, in the NDE records, is enabled. disable - Disables the export of AS number information. originate - Enables the export of origination AS numbers of source and destination IP addresses. peer - Enables the export of peer AS numbers of source and destination IP addresses.
OBJECT-TYPE    
  INTEGER disable(1), originate(2), peer(3)  

cseNetflowPerVlanIfGlobalEnable 1.3.6.1.4.1.9.9.97.1.3.15
Indicates whether 'creation of Netflow entries per VLAN interface' feature is enabled at the device level. If this object is set to 'false', netflow entries will be created for all VLANs. If this object is set to 'true', creation of netflow entries can be controlled by cseNetflowPerVlanIfCtrlTable.
OBJECT-TYPE    
  TruthValue  

cseNetflowPerVlanIfCtrlTable 1.3.6.1.4.1.9.9.97.1.3.16
A table to control netflow entry creation for each VLAN. When a VLAN is created, a corresponding entry is added to this table.
OBJECT-TYPE    
  SEQUENCE OF  
    CseNetflowPerVlanIfCtrlEntry

cseNetflowPerVlanIfCtrlEntry 1.3.6.1.4.1.9.9.97.1.3.16.1
An entry containing the configuration to enable or disable netflow entry creation for each VLAN.
OBJECT-TYPE    
  CseNetflowPerVlanIfCtrlEntry  

cseNetflowPerVlanIfCtrlVlan 1.3.6.1.4.1.9.9.97.1.3.16.1.1
Indicates the VLAN number on which creation of netflow entries is configured.
OBJECT-TYPE    
  VlanIndex  

cseNetflowPerVlanIfEnable 1.3.6.1.4.1.9.9.97.1.3.16.1.2
Specifies whether creation of netflow entries is enabled on this VLAN. If this object is set to 'true', the system will create netflow entries for this VLAN. If this object is set to 'false', the system will not create any netflow entries for this VLAN. When the value of cseNetflowPerVlanIfGlobalEnable is 'false', this object will not take effect.
OBJECT-TYPE    
  TruthValue  

cseL3Objects 1.3.6.1.4.1.9.9.97.1.4
OBJECT IDENTIFIER    

cseL3StatsTable 1.3.6.1.4.1.9.9.97.1.4.1
A table containing L3 statistics information on each switching engine.
OBJECT-TYPE    
  SEQUENCE OF  
    CseL3StatsEntry

cseL3StatsEntry 1.3.6.1.4.1.9.9.97.1.4.1.1
A conceptual row of cseL3StatsTable, containing L3 statistics maintained by a switching engine entity (identified by entPhysicalIndex). Each switching engine managed by this MIB module has an entry in this table.
OBJECT-TYPE    
  CseL3StatsEntry  

cseL3SwitchedTotalPkts 1.3.6.1.4.1.9.9.97.1.4.1.1.1
Total number of packets switched at Layer 3 by this switching engine.
OBJECT-TYPE    
  Counter32  

cseL3SwitchedTotalOctets 1.3.6.1.4.1.9.9.97.1.4.1.1.2
Number of octets in the total packets switched at Layer 3 by this switching engine.
OBJECT-TYPE    
  Counter64  

cseL3CandidateFlowHits 1.3.6.1.4.1.9.9.97.1.4.1.1.3
Number of L3 Cache hits for the candidate flow entries in this switching engine.
OBJECT-TYPE    
  Counter32  

cseL3EstablishedFlowHits 1.3.6.1.4.1.9.9.97.1.4.1.1.4
Number of L3 Cache hits for established flow entries in this switching engine.
OBJECT-TYPE    
  Counter32  

cseL3ActiveFlows 1.3.6.1.4.1.9.9.97.1.4.1.1.5
Number of active flows in the Layer 3 flow table of this switching engine.
OBJECT-TYPE    
  Gauge32  

cseL3FlowLearnFailures 1.3.6.1.4.1.9.9.97.1.4.1.1.6
Number of flows that failed to be learned because the Layer 3 flow table in this switching engine was full.
OBJECT-TYPE    
  Counter32  

cseL3IntFlowInvalids 1.3.6.1.4.1.9.9.97.1.4.1.1.7
Number of flow invalidation events received by this switching engine from the internal router(s).
OBJECT-TYPE    
  Counter32  

cseL3ExtFlowInvalids 1.3.6.1.4.1.9.9.97.1.4.1.1.8
Number of flow invalidation events received by this switching engine from external routers.
OBJECT-TYPE    
  Counter32  

cseL3SwitchedPktsPerSec 1.3.6.1.4.1.9.9.97.1.4.1.1.9
Number of packets switched per second at Layer 3 by this switching engine.
OBJECT-TYPE    
  Counter32  

cseL3VlanStatsTable 1.3.6.1.4.1.9.9.97.1.4.2
A table containing per-VLAN, Layer 3 statistics information per switching engine.
OBJECT-TYPE    
  SEQUENCE OF  
    CseL3VlanStatsEntry

cseL3VlanStatsEntry 1.3.6.1.4.1.9.9.97.1.4.2.1
A conceptual row of cseL3VlanStatsTable, containing per-VLAN Layer 3 statistics maintained by a switching engine (identified by entPhysicalIndex). An entry exists for each known VLAN for each switching engine.
OBJECT-TYPE    
  CseL3VlanStatsEntry  

cseL3VlanIndex 1.3.6.1.4.1.9.9.97.1.4.2.1.1
Vlan number for which the statistics are maintained by this entry.
OBJECT-TYPE    
  VlanIndex  

cseL3VlanInPkts 1.3.6.1.4.1.9.9.97.1.4.2.1.2
Number of packets Layer 3 forwarded from this Vlan to some other VLAN by this switching engine.
OBJECT-TYPE    
  Counter64  

cseL3VlanInOctets 1.3.6.1.4.1.9.9.97.1.4.2.1.3
Number of octets in packets Layer-3 forwarded from this Vlan to some other VLAN by this switching engine.
OBJECT-TYPE    
  Counter64  

cseL3VlanOutPkts 1.3.6.1.4.1.9.9.97.1.4.2.1.4
Number of packets Layer-3 forwarded to this Vlan by this switching engine.
OBJECT-TYPE    
  Counter64  

cseL3VlanOutOctets 1.3.6.1.4.1.9.9.97.1.4.2.1.5
Number of octets in packets Layer-3 forwarded to this Vlan by this switching engine.
OBJECT-TYPE    
  Counter64  

cseL3VlanInUnicastPkts 1.3.6.1.4.1.9.9.97.1.4.2.1.6
Number of unicast packets Layer 3 forwarded from this Vlan to some other VLAN by this switching engine.
OBJECT-TYPE    
  Counter64  

cseL3VlanInUnicastOctets 1.3.6.1.4.1.9.9.97.1.4.2.1.7
Number of octets in unicast packets Layer-3 forwarded from this Vlan to some other VLAN by this switching engine.
OBJECT-TYPE    
  Counter64  

cseL3VlanOutUnicastPkts 1.3.6.1.4.1.9.9.97.1.4.2.1.8
Number of unicast packets Layer 3 forwarded to this Vlan by this switching engine.
OBJECT-TYPE    
  Counter64  

cseL3VlanOutUnicastOctets 1.3.6.1.4.1.9.9.97.1.4.2.1.9
Number of octets in unicast packets Layer-3 forwarded to this Vlan by this switching engine.
OBJECT-TYPE    
  Counter64  

cseStatsFlowTable 1.3.6.1.4.1.9.9.97.1.4.3
A table of flow statistics per switch engine that is not covered in cseL3StatsTable.
OBJECT-TYPE    
  SEQUENCE OF  
    CseStatsFlowEntry

cseStatsFlowEntry 1.3.6.1.4.1.9.9.97.1.4.3.1
A conceptual row about slot based L3 flow statistics.
OBJECT-TYPE    
  CseStatsFlowEntry  

cseStatsFlowAged 1.3.6.1.4.1.9.9.97.1.4.3.1.1
Total number of layer 3 flows aged out by hardware. Management applications can control flow aging by setting the value of cseFlowEstablishedAgingTime object.
OBJECT-TYPE    
  Counter32  

cseStatsFlowPurged 1.3.6.1.4.1.9.9.97.1.4.3.1.2
Total number of layer 3 flows purged by software; it may happen because a router invalidates certain flows, or a router for which flows are being switched has been excluded from cseRouterTable, or access-list has changed, or certain features have been enabled that would purge certain flows (TCP interception, Web cache are examples of such features).
OBJECT-TYPE    
  Counter32  

cseStatsFlowParityFail 1.3.6.1.4.1.9.9.97.1.4.3.1.3
Total number of memory parity errors on accessing flows in the cache pools. It may be due to the internal RAM reading error, not necessarily the corrupted flow data.
OBJECT-TYPE    
  Counter32  

cseCacheUtilTable 1.3.6.1.4.1.9.9.97.1.4.4
A table of utilization levels in percentage of cache capacity per switch engine. Each row instance is the current flow utilization information in the cache pool of the corresponding switching engine.
OBJECT-TYPE    
  SEQUENCE OF  
    CseCacheUtilEntry

cseCacheUtilEntry 1.3.6.1.4.1.9.9.97.1.4.4.1
A row instance represents layer 3 flow utilization of a particular cache pool on a switching engine.
OBJECT-TYPE    
  CseCacheUtilEntry  

cseCacheUtilization 1.3.6.1.4.1.9.9.97.1.4.4.1.1
Flow utilization level in percentage in this switching engine. It includes the flow entries for both unicast and multicast. The lighter the utilization level, the less risk of dropping flows, i.e. the higher success-rate of flow insertion.
OBJECT-TYPE    
  Gauge32 0..100  

cseCacheEntriesCreated 1.3.6.1.4.1.9.9.97.1.4.4.1.2
This object indicates the total number of flow entries successfully created in this switching engine.
OBJECT-TYPE    
  Unsigned32  

cseCacheEntriesFailed 1.3.6.1.4.1.9.9.97.1.4.4.1.3
This object indicates the number of flow entries which were failed to be created in this switching engine.
OBJECT-TYPE    
  Unsigned32  

cseErrorStatsTable 1.3.6.1.4.1.9.9.97.1.4.5
A table of IP and IPX error counters per switch engine.
OBJECT-TYPE    
  SEQUENCE OF  
    CseErrorStatsEntry

cseErrorStatsEntry 1.3.6.1.4.1.9.9.97.1.4.5.1
A row instance represents layer-3 IP and IPX error counters on a switching engine.
OBJECT-TYPE    
  CseErrorStatsEntry  

cseIpPlenErrors 1.3.6.1.4.1.9.9.97.1.4.5.1.1
Indicates the number of IP length against physical length errors.
OBJECT-TYPE    
  Counter64  

cseIpTooShortErrors 1.3.6.1.4.1.9.9.97.1.4.5.1.2
Indicates the number of IP length too short errors.
OBJECT-TYPE    
  Counter64  

cseIpCheckSumErrors 1.3.6.1.4.1.9.9.97.1.4.5.1.3
Indicates the number of IP checksum errors.
OBJECT-TYPE    
  Counter64  

cseIpxPlenErrors 1.3.6.1.4.1.9.9.97.1.4.5.1.4
Indicates the number of IPX length against physical length errors.
OBJECT-TYPE    
  Counter64  

cseIpxTooShortErrors 1.3.6.1.4.1.9.9.97.1.4.5.1.5
Indicates the number of IPX length too short errors.
OBJECT-TYPE    
  Counter64  

cseErrorStatsLCTable 1.3.6.1.4.1.9.9.97.1.4.6
A table of IP and IPX error counters per switch engine.
OBJECT-TYPE    
  SEQUENCE OF  
    CseErrorStatsLCEntry

cseErrorStatsLCEntry 1.3.6.1.4.1.9.9.97.1.4.6.1
A row instance represents layer-3 IP and IPX error counters on a switching engine.
OBJECT-TYPE    
  CseErrorStatsLCEntry  

cseLCIpPlenErrors 1.3.6.1.4.1.9.9.97.1.4.6.1.1
Indicates the number of IP length against physical length errors.
OBJECT-TYPE    
  Counter32  

cseLCIpTooShortErrors 1.3.6.1.4.1.9.9.97.1.4.6.1.2
Indicates the number of IP length too short errors.
OBJECT-TYPE    
  Counter32  

cseLCIpCheckSumErrors 1.3.6.1.4.1.9.9.97.1.4.6.1.3
Indicates the number of IP checksum errors.
OBJECT-TYPE    
  Counter32  

cseLCIpxPlenErrors 1.3.6.1.4.1.9.9.97.1.4.6.1.4
Indicates the number of IPX length against physical length errors.
OBJECT-TYPE    
  Counter32  

cseLCIpxTooShortErrors 1.3.6.1.4.1.9.9.97.1.4.6.1.5
Indicates the number of IPX length too short errors.
OBJECT-TYPE    
  Counter32  

cseL3SwitchedAggrPktsPerSec 1.3.6.1.4.1.9.9.97.1.4.7
Number of packets switched per second at Layer 3 by the entire system.
OBJECT-TYPE    
  Counter32  

cseProtocolFilter 1.3.6.1.4.1.9.9.97.1.5
OBJECT IDENTIFIER    

cseProtocolFilterEnable 1.3.6.1.4.1.9.9.97.1.5.1
Indicates if protocol filtering is enabled in the device.
OBJECT-TYPE    
  TruthValue  

cseProtocolFilterPortTable 1.3.6.1.4.1.9.9.97.1.5.2
A table containing the protocol filtering configuration and status information on ports.
OBJECT-TYPE    
  SEQUENCE OF  
    CseProtocolFilterPortEntry

cseProtocolFilterPortEntry 1.3.6.1.4.1.9.9.97.1.5.2.1
A conceptual row in the cseProtocolFilterPortTable, representing a Protocol filter configuration status information for a particular port (identified by ifIndex) and protocol type.
OBJECT-TYPE    
  CseProtocolFilterPortEntry  

cseProtocolFilterPortProtocol 1.3.6.1.4.1.9.9.97.1.5.2.1.1
The protocol (group) to filter, used here as the secondary index.
OBJECT-TYPE    
  INTEGER ip(1), ipx(2), grpProtocols(3)  

cseProtocolFilterPortAdminStatus 1.3.6.1.4.1.9.9.97.1.5.2.1.2
An indication of the administrative status of the protocol filtering on this interface. - on(1) indicates that the interface will send and receive the traffic for protocol specified in cseProtocolFilterPortProtocol. - off(2) indicates that the interface will not receive traffic for this protocol, or if this feature is not supported. - auto(3) indicates that the corresponding cseProtocolFilterPortOperStatus will transit to 'on' after receiving one packet of this protocol type.
OBJECT-TYPE    
  INTEGER on(1), off(2), auto(3)  

cseProtocolFilterPortOperStatus 1.3.6.1.4.1.9.9.97.1.5.2.1.3
An indication of the operational status of filtering for this protocol on this interface. - on(1) indicates that the interface will send and receive the protocol traffic. - off(2) indicates that the interface will drop all traffic belonging to this protocol. - notSupported(3) indicates the hardware does not support protocol filtering.
OBJECT-TYPE    
  INTEGER on(1), off(2), notSupported(3)  

cseUcastCache 1.3.6.1.4.1.9.9.97.1.6
OBJECT IDENTIFIER    

cseUcastCacheTable 1.3.6.1.4.1.9.9.97.1.6.1
A control table used to purge certain types of IP/IPX layer 3 unicast flows stored in the cache pool.
OBJECT-TYPE    
  SEQUENCE OF  
    CseUcastCacheEntry

cseUcastCacheEntry 1.3.6.1.4.1.9.9.97.1.6.1.1
A conceptual row in the cseUcastCacheTable, used to set up flow clearing criteria. The actual purging is started by setting the value of cseUcastCacheStatus to 'active'. Once a row becomes active, values within the row cannot be modified, except by setting it to 'notInService' first or deleting and re-creating the row.
OBJECT-TYPE    
  CseUcastCacheEntry  

cseUcastCacheIndex 1.3.6.1.4.1.9.9.97.1.6.1.1.1
An arbitrary integer which uniquely identifies the flow purge contained in this row instance.
OBJECT-TYPE    
  Unsigned32  

cseUcastCacheFlowType 1.3.6.1.4.1.9.9.97.1.6.1.1.2
Setting each value causes the appropriate action: 'dstOnly' - causes purge of flows in the cache whose absolute destination IP addresses match the address part of the value set in the cseUcastCacheDest object. If cseUcastCacheDestMask is also specified at the same time, it will be applied to the address part of cseUcastCacheDest. 'srcOrDst' - causes purge of flows in the cache whose either absolute source or destination IP addresses match the address parts of the values set in cseUcastCacheSource or cseUcastCacheDest. If cseUcastCacheDestMask/cseUcastCacheSrcMask also specified, they will be applied to the address parts of cseUcastCacheSource/ cseUcastCacheDest appropriately. 'srcAndDst' - causes purge of flows in the cache whose both absolute source and destination IP addresses match the address parts of values set in cseUcastCacheSource and cseUcastCacheDest objects. If cseUcastCacheSrcMask and cseUcastCacheDestMask also specified, they will be applied to the address parts of cseUcastCacheSource and cseUcastCacheDest. 'fullFlow' - causes purge of IP flows whose IP addresses and transport port numbers match the values set in cseUcastCacheDest and cseUcastCacheSource objects. If either cseUcastCacheDestMask or cseUcastCacheSrcMask objects have valid values, they will be applied to the respective address parts of cseUcastCacheDest and cseUcastCacheSource objects. This option is typically used to purge flows relevant to specific applications such as FTP, WWW, TELNET, etc. 'ipxDstOnly' - causes purge of IPX flows in the cache whose absolute destination IPX address match the address part of the value set in cseUcastCacheDest object. if cseUcastCacheDestMask holds valid value at the same time, it will be applied to the address part of cseUcastCacheDest. 'ipxSrcAndDst' - causes purge of IPX flows in the cache whose both absolute source and destination IPX addresses match the address parts of the values set in cseUcastCacheSource and cseUcastCacheDest objects. If either of cseUcastCacheSrcMask or cseUcastCacheDestMask have valid values at the same time, they will be applied to the respective address parts of cseUcastCacheSource and cseUcastCacheDest objects. 'any' - causes purge of all established flows currently in the cache. The values of cseUcastCacheDest, cseUcastCacheSource, cseUcastCacheDestMask, cseUcastCacheSrcMask, and cseUcastCacheTransport should be ignored in this case. Note: 1. When the row instance is initialized, the value of this object instance will be set to 'any'. 2. The rest flow parameter variables will not be instantiated until they get set by management applications based on the value of cseUcastCacheFlowType object.
OBJECT-TYPE    
  INTEGER any(1), dstOnly(2), srcOrDst(3), srcAndDst(4), fullFlow(5), ipxDstOnly(6), ipxSrcAndDst(7)  

cseUcastCacheTransport 1.3.6.1.4.1.9.9.97.1.6.1.1.3
The IP transport protocol type (if applicable) of the specified switched flows to be purged; it will be instantiated if and only if it gets set by the management applications and the value of cseUcastCacheFlowMask is equal to 'fullFlow'. Its value can not be modified when the corresponding instance of cseUcastCacheStatus is 'active'.
OBJECT-TYPE    
  INTEGER udp(1), tcp(2)  

cseUcastCacheDest 1.3.6.1.4.1.9.9.97.1.6.1.1.4
Destination network address and port number (if applicable). The port field is ignored for IPX flows and IP flows if the value of cseUcastCacheFlowMask is not equal to 'fullFlow'. Its value can not be modified when the corresponding instance of cseUcastCacheStatus is 'active'.
OBJECT-TYPE    
  FlowAddressComponent  

cseUcastCacheDestMask 1.3.6.1.4.1.9.9.97.1.6.1.1.5
If instantiated, specified and applicable, the destination address mask will be applied to the value of cseUcastCacheDest in the same row instance. Its value can not be modified when the corresponding instance of cseUcastCacheStatus is 'active'.
OBJECT-TYPE    
  FlowAddressComponent  

cseUcastCacheSource 1.3.6.1.4.1.9.9.97.1.6.1.1.6
Source network address and port number (if applicable). The port field is ignored for IPX flows and IP flows if the value of cseUcastCacheFlowMask is not equal to 'fullFlow'. Its value can not be modified when the corresponding instance of cseUcastCacheStatus is 'active'.
OBJECT-TYPE    
  FlowAddressComponent  

cseUcastCacheSrcMask 1.3.6.1.4.1.9.9.97.1.6.1.1.7
If instantiated, specified and applicable, the source address mask will be applied to the value of cseUcastCacheSource in the same row instance. Its value can not be modified when the corresponding instance of cseUcastCacheStatus is 'active'.
OBJECT-TYPE    
  FlowAddressComponent  

cseUcastCacheRtrIp 1.3.6.1.4.1.9.9.97.1.6.1.1.8
IP address of the router (internal or external) for which the flows are being switched, and need to be purged. An 'all-zero' value is a wildcard IP address for any router. Its value can not be modified when the corresponding instance of cseUcastCacheStatus is 'active'.
OBJECT-TYPE    
  IpAddress  

cseUcastCacheOwner 1.3.6.1.4.1.9.9.97.1.6.1.1.9
The manager entity that configured this entry and is therefore using the resources assigned to it.
OBJECT-TYPE    
  OwnerString  

cseUcastCacheStatus 1.3.6.1.4.1.9.9.97.1.6.1.1.10
The status object used to manage rows in this table. When set to active(1), the flow purge is initiated, and the value of cseUcastCacheResult object becomes 'purging'. However, this object can be set to active(1) only after all the appropriate objects for this query as defined by the value set in the cseUcastCacheFlowType object, have also been set. Upon the completion of flow purge, the value of cseUcastCacheResult object changes to 'notPurging'. Once a row becomes active, values within the row cannot be modified, except by setting it to 'notInService' first, or deleting and re-creating it.
OBJECT-TYPE    
  RowStatus  

cseUcastCacheResult 1.3.6.1.4.1.9.9.97.1.6.1.1.11
state of the flow purging operation. 'purging' - purging operation is proceeding 'notPurging' - the purging operation completed, or not started yet.
OBJECT-TYPE    
  INTEGER purging(1), notPurging(2)  

cseMcastCache 1.3.6.1.4.1.9.9.97.1.7
OBJECT IDENTIFIER    

cseMcastCacheTable 1.3.6.1.4.1.9.9.97.1.7.1
A control table used to purge specified IP multicast flows from the switch engine.
OBJECT-TYPE    
  SEQUENCE OF  
    CseMcastCacheEntry

cseMcastCacheEntry 1.3.6.1.4.1.9.9.97.1.7.1.1
A conceptual row in the cseMcastCacheTable, used to set up flow clearing criteria. The actual purging is started by setting the value of cseMcastCacheStatus to 'active'. Once a row becomes active, values within the row cannot be modified, except by setting it to 'notInService' first, or deleting and re-creating the row.
OBJECT-TYPE    
  CseMcastCacheEntry  

cseMcastCacheIndex 1.3.6.1.4.1.9.9.97.1.7.1.1.1
An arbitrary integer which uniquely identifies the flow purge contained in the current row instance.
OBJECT-TYPE    
  Unsigned32  

cseMcastCacheFlowType 1.3.6.1.4.1.9.9.97.1.7.1.1.2
Setting each value causes the appropriate action: 'any' - causes purge of all established IP multicast layer 3 flows in the cache. The value of cseMcastCacheGrp, and cseMcastCacheSrc will be ignored in this case. 'group' - causes purge of flows whose multicast group IP address match the values of cseMcastCacheGrp. 'grpAndSrc' - causes purge of multicast flows whose both group IP address and source Ip address match the values of cseMcastCacheGrp and cseMcastCacheSrc. Note: 1. The instance of this object is initialized to 'any' when the corresponding row instance is being instantiated. 2. Flow parameter variables, cseMcastCacheGrp, cseMcastCacheSrc, cseMcastCacheRtrIp will not be instantiated until they get set by management applications (in such cases, cseMcastCacheFlowType object should be set to a value other than 'any').
OBJECT-TYPE    
  INTEGER any(1), group(2), grpAndSrc(3)  

cseMcastCacheGrp 1.3.6.1.4.1.9.9.97.1.7.1.1.3
Specifying multicast group IP address of the flows to be cleared. Its value can not be modified when the corresponding instance of cseMcastCacheStatus is 'active'.
OBJECT-TYPE    
  McastGroupIp  

cseMcastCacheSrc 1.3.6.1.4.1.9.9.97.1.7.1.1.4
The source address of the IP multicast flows to be purged. Its value can not be modified when the corresponding instance of cseMcastCacheStatus is 'active'.
OBJECT-TYPE    
  IpAddress  

cseMcastCacheRtrIp 1.3.6.1.4.1.9.9.97.1.7.1.1.5
The IP address of the router whose flows are currently being switched, and will be purged. An 'all-zero' value is a wildcard IP address for any router. Its value can not be modified when the corresponding instance of cseMcastCacheStatus is 'active'.
OBJECT-TYPE    
  IpAddress  

cseMcastCacheOwner 1.3.6.1.4.1.9.9.97.1.7.1.1.6
The manager entity that configured this entry and is therefore using the resources assigned to it.
OBJECT-TYPE    
  OwnerString  

cseMcastCacheResult 1.3.6.1.4.1.9.9.97.1.7.1.1.7
state of the flow purging operation. 'purging' - purging operation is proceeding 'notPurging' - the purging operation completed, or not started yet.
OBJECT-TYPE    
  INTEGER purging(1), notPurging(2)  

cseMcastCacheStatus 1.3.6.1.4.1.9.9.97.1.7.1.1.8
The status object used to manage rows in this table. When set to active(1), the flow purge is initiated, and the value of cseMcastCacheResult object becomes 'purging'. However, this object can be set to active(1) only after all the appropriate objects for this query as defined by the value set in the cseMcastCacheFlowType object, have also been set. Upon the completion of flow purge, the value of cseMcastCacheResult object changes to 'notPurging'. Once a row becomes active, values within the row cannot be modified, except by setting it to 'notInService' first, or deleting and re-creating it.
OBJECT-TYPE    
  RowStatus  

cseCef 1.3.6.1.4.1.9.9.97.1.8
OBJECT IDENTIFIER    

cseCefFibTable 1.3.6.1.4.1.9.9.97.1.8.1
This table contains the information stored in the device's forwarding information base (FIB). FIB is a forwarding scheme that utilizes matching pattern to provide optimized lookup for efficient packet forwarding. It contains a forwarding table which consist of matching criteria for incoming traffic as well as information to forward traffic that matched defined criteria.
OBJECT-TYPE    
  SEQUENCE OF  
    CseCefFibEntry

cseCefFibEntry 1.3.6.1.4.1.9.9.97.1.8.1.1
Each row contains the IP address type, the final destination IP address, the final destination IP address mask as well as the FIB entry type.
OBJECT-TYPE    
  CseCefFibEntry  

cseCefFibIndex 1.3.6.1.4.1.9.9.97.1.8.1.1.1
The index of this table entry.
OBJECT-TYPE    
  Unsigned32  

cseCefFibAddrType 1.3.6.1.4.1.9.9.97.1.8.1.1.2
The type of IP address denoted in cseCefFibDestIp and cseCefFibDestIpMask object.
OBJECT-TYPE    
  InetAddressType  

cseCefFibDestIp 1.3.6.1.4.1.9.9.97.1.8.1.1.3
The destination IP address specified in IP packet header.
OBJECT-TYPE    
  InetAddress  

cseCefFibDestIpMask 1.3.6.1.4.1.9.9.97.1.8.1.1.4
The specified destination IP address mask.
OBJECT-TYPE    
  InetAddress  

cseCefFibType 1.3.6.1.4.1.9.9.97.1.8.1.1.5
Indicates the FIB entry type. other(1) indicates that this FIB entry type is none of the following. resolved(2) indicates that IP traffic matched the destination prefix of this entry is associated with a valid next-hop address. bridge(3) indicates that IP traffic matched the destination prefix of this entry will be forwarded using Layer 2 look up result. drop(4) indicates that IP traffic matched the destination prefix of this entry will be dropped. connected(5) indicates that IP traffic matched the destination prefix of this entry is associated with a connected network. receive(6) indicates that IP traffic matched the destination prefix of this entry will be sent to a router interface. wildcard(7) indicates this FIB entry will match all traffic. tunnel(8) indicates this FIB entry applied to tunneling traffic. default(9) indicates that IP traffic matched the destination prefix of this entry will be forwarded using a default route.
OBJECT-TYPE    
  INTEGER other(1), resolved(2), bridge(3), drop(4), connected(5), receive(6), wildcard(7), tunnel(8), default(9)  

cseCefAdjacencyTable 1.3.6.1.4.1.9.9.97.1.8.3
This table contains information stored in the device's adjacency table. Entry in this table is linked to entry of cseCefFibTable by its cseCefFibIndex object.
OBJECT-TYPE    
  SEQUENCE OF  
    CseCefAdjacencyEntry

cseCefAdjacencyEntry 1.3.6.1.4.1.9.9.97.1.8.3.1
Each row contains next hop IP address, next-hop Ethernet address, adjacency type, and number of bytes and packets transmitted to each adjacency entry. Next hop encapsulation type and MTU value are also available if supported by the device.
OBJECT-TYPE    
  CseCefAdjacencyEntry  

cseCefAdjacencyIndex 1.3.6.1.4.1.9.9.97.1.8.3.1.1
The adjacency index of this table entry.
OBJECT-TYPE    
  Unsigned32  

cseCefAdjacencyAddrType 1.3.6.1.4.1.9.9.97.1.8.3.1.2
The type of IP address denoted in cseCefAdjacencyNextHopIp object.
OBJECT-TYPE    
  InetAddressType  

cseCefAdjacencyNextHopIp 1.3.6.1.4.1.9.9.97.1.8.3.1.3
The next hop IP address.
OBJECT-TYPE    
  InetAddress  

cseCefAdjacencyNextHopMac 1.3.6.1.4.1.9.9.97.1.8.3.1.4
The next hop Ethernet address.
OBJECT-TYPE    
  MacAddress  

cseCefAdjacencyNextHopIfIndex 1.3.6.1.4.1.9.9.97.1.8.3.1.5
Indicates the next hop interface ifIndex.
OBJECT-TYPE    
  InterfaceIndexOrZero  

cseCefAdjacencyType 1.3.6.1.4.1.9.9.97.1.8.3.1.6
Indicates this adjacency entry type. other(1) indicates the adjacency entry type is none of the following. punt(2) indicates entry that sends traffic to the router. glean(3) indicates entry that needs to be gleaned for incoming traffic. drop(4) indicates entry that drops packets. null(5) indicates entry that drops packets destined for the Null0 interface. noRewrite(6) indicates entry that sends traffic to the router when rewrite information is incomplete. forceDrop(7) indicates entry that drop packets due to ARP throttling. connect(8) indicates entry that contains complete rewrite information. unresolved(9) indicates entry that next hop traffic is unresolved. loopback(10) indicates entry that drops packets destined for loopback interface. tunnel(11) indicates entry that next hop traffic is through a tunnel.
OBJECT-TYPE    
  INTEGER other(1), punt(2), glean(3), drop(4), null(5), noRewrite(6), forceDrop(7), connect(8), unresolved(9), loopback(10), tunnel(11)  

cseCefAdjacencyPkts 1.3.6.1.4.1.9.9.97.1.8.3.1.7
Indicates the number of Layer 3 packets transmitted to this adjacency entry.
OBJECT-TYPE    
  Counter64  

cseCefAdjacencyOctets 1.3.6.1.4.1.9.9.97.1.8.3.1.8
Indicates the number of Layer 3 octets transmitted to this adjacency entry.
OBJECT-TYPE    
  Counter64  

cseCefAdjacencyEncap 1.3.6.1.4.1.9.9.97.1.8.3.1.9
Indicates the next hop destination encapsulation type. arpa(1) indicates that next hop destination used ARPA encapsulation type to forward packets. raw(2) indicates that next hop destination used RAW encapsulation type to forward packets. sap(3) indicates that next hop destination used SAP encapsulation type to forward packets. snap(4) indicates that next hop destination used SNAP encapsulation type to forward packets.
OBJECT-TYPE    
  INTEGER arpa(1), raw(2), sap(3), snap(4)  

cseCefAdjacencyMTU 1.3.6.1.4.1.9.9.97.1.8.3.1.10
Indicates the next hop destination MTU value.
OBJECT-TYPE    
  Unsigned32  

cseTcamUsage 1.3.6.1.4.1.9.9.97.1.9
OBJECT IDENTIFIER    

cseTcamUsageTable 1.3.6.1.4.1.9.9.97.1.9.1
This table contains the resource usage of TCAM (Ternary Content Addressable Memory) in the device. Not all the resource types denoted by cseTcamResourceType object are supported. If that is the case, the corresponding row for that type will not be instantiated in this table.
OBJECT-TYPE    
  SEQUENCE OF  
    CseTcamUsageEntry

cseTcamUsageEntry 1.3.6.1.4.1.9.9.97.1.9.1.1
Each row contains a short description of the resource type, the total amount of TCAM allocated for that type as well as the amount of allocated resource has been used up.
OBJECT-TYPE    
  CseTcamUsageEntry  

cseTcamResourceType 1.3.6.1.4.1.9.9.97.1.9.1.1.1
The resource type which take up TCAM space. aclStorageMask(1) indicates that TCAM space is allocated to store ACL masks. aclStorageValue(2) indicates that TCAM space is allocated to store ACL value. aclDynamicStorageMask(3) indicates that TCAM space is allocated to dynamically store ACL masks. aclDynamicStorageValue(4) indicates that TCAM space is allocated to dynamically store ACL values. qosStorageMask(5) indicates that TCAM space is allocated to store QoS masks. qosStorageValue(6) indicates that TCAM space is allocated to store QoS value. qosDynamicStorageMask(7) indicates that TCAM space is allocated to dynamically store QoS masks. qosDynamicStorageValue(8) indicates that TCAM space is allocated to dynamically store QoS values. l4PortOperator(9) indicates that TCAM space is allocated for layer 4 port operators purpose. interfaceMapping(10) indicates that TCAM space is allocated for interface mapping purpose. ingressInterfaceMapping(11) indicates that TCAM space is allocated for ingress interface mapping purpose. egressInterfaceMapping(12) indicates that TCAM space is allocated for egress interface mapping purpose. louSource(13) indicates that TCAM space is allocated as source LOUs (Logical Operation Unit). louDestination(14) indicates that TCAM space is allocated as destination LOUs. andOr(15) indicates that TCAM space is allocated for ANDOR purpose. orAnd(16) indicates that TCAM space is allocated for ORAND purpose. aclAdjacency(17) indicates that TCAM space is allocated for ACL adjacency purpose. aclHighStorageMask(18) indicates that high bank TCAM space is allocated to store ACL masks. aclHighStorageValue(19) indicates that high bank TCAM space is allocated to store ACL value. aclLowStorageMask(20) indicates that low bank TCAM space is allocated to store ACL masks. aclLowStorageValue(21) indicates that low bank TCAM space is allocated to store ACL values. qosHighStorageMask(22) indicates that high bank TCAM space is allocated to store QoS masks. qosHighStorageValue(23) indicates that high bank TCAM space is allocated to store QoS value. qosLowStorageMask(24) indicates that low bank TCAM space is allocated to store QoS masks. qosLowStorageValue(25) indicates that low bank TCAM space is allocated to store QoS values. sgacl(26) indicates that TCAM space is allocated for SGACL (Security Group Access Control List) purpose. accounting(27) indicates that TCAM space is allocated for accounting purpose such as AS (Autonomous System) based accounting, classification based accounting. ipv6Ext(28) indicates that TCAM space is allocated for IPv6 Extended Header lookup purpose. ethertype(29) indicates that TCAM space is allocated for layer2 ethertype lookup purpose. destInfo(30) indicates that TCAM space is allocated for destination information lookup purpose.
OBJECT-TYPE    
  INTEGER aclStorageMask(1), aclStorageValue(2), aclDynamicStorageMask(3), aclDynamicStorageValue(4), qosStorageMask(5), qosStorageValue(6), qosDynamicStorageMask(7), qosDynamicStorageValue(8), l4PortOperator(9), interfaceMapping(10), ingressInterfaceMapping(11), egressInterfaceMapping(12), louSource(13), louDestination(14), andOr(15), orAnd(16), aclAdjacency(17), aclHighStorageMask(18), aclHighStorageValue(19), aclLowStorageMask(20), aclLowStorageValue(21), qosHighStorageMask(22), qosHighStorageValue(23), qosLowStorageMask(24), qosLowStorageValue(25), sgacl(26), accounting(27), ipv6Ext(28), ethertype(29), destInfo(30)  

cseTcamResourceDescr 1.3.6.1.4.1.9.9.97.1.9.1.1.2
The short description of the resource type.
OBJECT-TYPE    
  SnmpAdminString  

cseTcamResourceUsed 1.3.6.1.4.1.9.9.97.1.9.1.1.3
The amount of TCAM resource has been used up for this resource type.
OBJECT-TYPE    
  Unsigned32  

cseTcamResourceTotal 1.3.6.1.4.1.9.9.97.1.9.1.1.4
The total amount of TCAM resource is allocated for this resource type.
OBJECT-TYPE    
  Unsigned32  

cseMet 1.3.6.1.4.1.9.9.97.1.10
OBJECT IDENTIFIER    

cseMetUsageTable 1.3.6.1.4.1.9.9.97.1.10.1
This table contains the resource usage of MET (Multicast Expansion Table) in the device.
OBJECT-TYPE    
  SEQUENCE OF  
    CseMetUsageEntry

cseMetUsageEntry 1.3.6.1.4.1.9.9.97.1.10.1.1
Each row contains the total number of entries in each MET, the number of free entries in unallocated as well as allocated space of the MET. Each row represents MET data maintained by each module (identified by its entPhysicalIndex) which is capable of this feature.
OBJECT-TYPE    
  CseMetUsageEntry  

cseMetIndex 1.3.6.1.4.1.9.9.97.1.10.1.1.1
A value uniquely identifies a MET in a module.
OBJECT-TYPE    
  Unsigned32  

cseMetTotalEntries 1.3.6.1.4.1.9.9.97.1.10.1.1.2
The total number of entries in this MET.
OBJECT-TYPE    
  Unsigned32  

cseMetUnallocatedSpcFreeEntries 1.3.6.1.4.1.9.9.97.1.10.1.1.3
The number of free entries reside in unallocated space of this MET.
OBJECT-TYPE    
  Unsigned32  

cseMetAllocatedSpcFreeEntries 1.3.6.1.4.1.9.9.97.1.10.1.1.4
The number of free entries reside in allocated space of this MET.
OBJECT-TYPE    
  Unsigned32  

cseMIBNotifications 1.3.6.1.4.1.9.9.97.2
OBJECT IDENTIFIER    

cseMIBConformance 1.3.6.1.4.1.9.9.97.3
OBJECT IDENTIFIER    

cseMIBCompliances 1.3.6.1.4.1.9.9.97.3.1
OBJECT IDENTIFIER    

cseMIBCompliance 1.3.6.1.4.1.9.9.97.3.1.1
The compliance statement for the CISCO-SWITCH_ENGINE-MIB MIB.
MODULE-COMPLIANCE    

cseMIBCompliance2 1.3.6.1.4.1.9.9.97.3.1.2
The compliance statement for the CISCO-SWITCH-ENGINE-MIB MIB.
MODULE-COMPLIANCE    

cseMIBCompliance3 1.3.6.1.4.1.9.9.97.3.1.3
The compliance statement for the CISCO-SWITCH-ENGINE-MIB MIB.
MODULE-COMPLIANCE    

cseMIBCompliance4 1.3.6.1.4.1.9.9.97.3.1.4
The compliance statement for the CISCO-SWITCH-ENGINE-MIB MIB.
MODULE-COMPLIANCE    

cseMIBCompliance5 1.3.6.1.4.1.9.9.97.3.1.5
The compliance statement for the CISCO-SWITCH-ENGINE-MIB MIB.
MODULE-COMPLIANCE    

cseMIBCompliance6 1.3.6.1.4.1.9.9.97.3.1.6
The compliance statement for the CISCO-SWITCH-ENGINE-MIB MIB.
MODULE-COMPLIANCE    

cseMIBCompliance7 1.3.6.1.4.1.9.9.97.3.1.7
The compliance statement for the CISCO-SWITCH-ENGINE-MIB MIB.
MODULE-COMPLIANCE    

cseMIBGroups 1.3.6.1.4.1.9.9.97.3.2
OBJECT IDENTIFIER    

cseStatisticsGroup 1.3.6.1.4.1.9.9.97.3.2.1
A collection of objects providing switch engine statistics.
OBJECT-GROUP    

cseStatisticsGroup2 1.3.6.1.4.1.9.9.97.3.2.2
A collection of objects providing switch engine statistics on aged/purged flows, and the cache utilizations.
OBJECT-GROUP    

cseVlanStatisticsGroup 1.3.6.1.4.1.9.9.97.3.2.3
A collection of objects providing per-vlan switch engine statistics, if supported.
OBJECT-GROUP    

cseRouterGroup 1.3.6.1.4.1.9.9.97.3.2.4
A collection of objects providing information on routers which are used to support layer 3 switching in the system.
OBJECT-GROUP    

cseFlowMgmtGroup 1.3.6.1.4.1.9.9.97.3.2.5
A collection of objects providing information for determining the L3 flow switching performance in the switching engine. There may be some platform specific limitations when performing a SET on some of these objects. The following are valid for Catalyst 5000 platforms: - cseFlowEstablishedAgingTime has a default value of 256. - cseFlowFastAgePktThreshold can only be set to 1, 3, 7, 15, 31 or 63 packets. If the packet threshold is not configured to one of these values, it will be adjusted to the closest value. - cseFlowFastAgingTime can be set to only values that are multiples of 8 in the range (0..128). If it is set to a value that is not multiple of 8, then the closest value that is a multiple of 8 will take effect. The default value for fast aging time is 32 seconds. (i.e. less than cseFlowFastAgePktThreshold number of packets were switched within 32 seconds after the an L3 flow entry was established). - cseFlowIPXEstablishedAgingTime has a default value of 256.
OBJECT-GROUP    

cseNetflowLSGroup 1.3.6.1.4.1.9.9.97.3.2.6
A collection of objects providing information on the Netflow LAN switching Data Export feature, if supported.
OBJECT-GROUP    

cseProtocolFilterGroup 1.3.6.1.4.1.9.9.97.3.2.7
A collection of objects providing information on the Protocol filter feature, if supported.
OBJECT-GROUP    

cseFlowMcastMgmtGroup 1.3.6.1.4.1.9.9.97.3.2.8
A collection of objects for querying IP multicast flows stored in hardware switching cache.
OBJECT-GROUP    

cseUcastCachePurgeGroup 1.3.6.1.4.1.9.9.97.3.2.9
A collection of objects providing IP/IPX unicast flow cache purging function.
OBJECT-GROUP    

cseMcastCachePurgeGroup 1.3.6.1.4.1.9.9.97.3.2.10
A collection of objects providing IP multicast flow cache purge function.
OBJECT-GROUP    

cseFlowMgmtOperStatusGroup 1.3.6.1.4.1.9.9.97.3.2.11
A collection of objects providing operating status information on aging time for flows used in L3 switching.
OBJECT-GROUP    

cse4kVlanGroup 1.3.6.1.4.1.9.9.97.3.2.12
A collection of objects providing information for VLANS with VlanIndex from 1024 to 4095.
OBJECT-GROUP    

cseNDEMandatoryGroup 1.3.6.1.4.1.9.9.97.3.2.13
A collection of objects providing information on the type of filter support, status and the version of NDE used.
OBJECT-GROUP    

cseNDESingleFilterGroup 1.3.6.1.4.1.9.9.97.3.2.14
A collection of objects providing information on the Netflow LAN switching Data Export feature, with a single host and a single filter support.
OBJECT-GROUP    

cseNDEMultipleFiltersGroup 1.3.6.1.4.1.9.9.97.3.2.15
A collection of objects providing information on the Netflow LAN switching Data Export feature, with multiple filter support.
OBJECT-GROUP    

cseFlowMgmtGroupRev1 1.3.6.1.4.1.9.9.97.3.2.16
A collection of objects providing information for determining the L3 flow switching performance in the switching engine. There may be some platform specific limitations when performing a SET on some of these objects. The following are valid for Catalyst 5000 platforms: - cseFlowEstablishedAgingTime has a default value of 256. - cseFlowFastAgePktThreshold can only be set to 1, 3, 7, 15, 31 or 63 packets. If the packet threshold is not configured to one of these values, it will be adjusted to the closest value. - cseFlowFastAgingTime can be set to only values that are multiples of 8 in the range (0..128). If it is set to a value that is not multiple of 8, then the closest value that is a multiple of 8 will take effect. The default value for fast aging time is 32 seconds. (i.e. less than cseFlowFastAgePktThreshold number of packets were switched within 32 seconds after the an L3 flow entry was established). - cseFlowIPXEstablishedAgingTime has a default value of 256.
OBJECT-GROUP    

cseL3ErrorsGroup 1.3.6.1.4.1.9.9.97.3.2.17
A collection of objects providing the IP and IPX error statistics.
OBJECT-GROUP    

cseBridgedFlowGroup 1.3.6.1.4.1.9.9.97.3.2.18
A collection of objects control the reporting of intra-vlan bridged flow statistics.
OBJECT-GROUP    

cseVlanStatisticsExtGroup 1.3.6.1.4.1.9.9.97.3.2.19
A collection of objects providing additional per-vlan switch engine statistics, if supported.
OBJECT-GROUP    

cseProtocolFilterExtGroup 1.3.6.1.4.1.9.9.97.3.2.20
A collection of objects providing additional information on the Protocol filter feature, if supported.
OBJECT-GROUP    

cseFlowMgmtExtGroup 1.3.6.1.4.1.9.9.97.3.2.21
A collection of objects providing additional information on the L3 flow switching in the switching engine.
OBJECT-GROUP    

cseFlowMgmtExtGroup1 1.3.6.1.4.1.9.9.97.3.2.22
A collection of objects providing additional information on the L3 flow switching in the switching engine.
OBJECT-GROUP    

cseNDEReportGroup 1.3.6.1.4.1.9.9.97.3.2.23
A collection of objects providing the configuration on NDE ifIndex report feature.
OBJECT-GROUP    

cseStatisticsFlowGroup 1.3.6.1.4.1.9.9.97.3.2.24
A collection of object providing switch engine statistics on total number of installed flows.
OBJECT-GROUP    

cseFlowMgmtExtGroup2 1.3.6.1.4.1.9.9.97.3.2.25
A collection of objects providing additional information on the L3 flow switching in the switching engine.
OBJECT-GROUP    

cseNDESingleFilterGroupRev1 1.3.6.1.4.1.9.9.97.3.2.26
A collection of objects providing information on the Netflow LAN switching Data Export feature, with a single filter support.
OBJECT-GROUP    

cseCefFibAdjacencyGroup 1.3.6.1.4.1.9.9.97.3.2.27
A collection of objects providing FIB and adjacency information available in the device.
OBJECT-GROUP    

cseCefAdjacencyEncapGroup 1.3.6.1.4.1.9.9.97.3.2.28
A collection of object providing adjacency next hop encapsulation information available in the device.
OBJECT-GROUP    

cseCefAdjacencyMTUGroup 1.3.6.1.4.1.9.9.97.3.2.29
A collection of object providing adjacency next hop MTU information available in the device.
OBJECT-GROUP    

cseTcamUsageGroup 1.3.6.1.4.1.9.9.97.3.2.30
A collection of objects providing the resource usage information on TCAM available in the device.
OBJECT-GROUP    

cseL3ErrorsLCGroup 1.3.6.1.4.1.9.9.97.3.2.31
A collection of objects providing the IP and IPX error statistics.
OBJECT-GROUP    

cseNetflowASInfoExportGroup 1.3.6.1.4.1.9.9.97.3.2.32
A collection of object providing AS number information export control.
OBJECT-GROUP    

cseNetflowPerVlanIfGroup 1.3.6.1.4.1.9.9.97.3.2.33
A collection of objects providing control of netflow entry creation per vlan.
OBJECT-GROUP    

cseMetUsageGroup 1.3.6.1.4.1.9.9.97.3.2.34
A collection of objects providing MET utilization information.
OBJECT-GROUP    

cseFlowMcastMgmtGroup1 1.3.6.1.4.1.9.9.97.3.2.35
A collection of objects for querying IP multicast flows stored in hardware switching cache.
OBJECT-GROUP    

cseFlowMcastRtrMgmtGroup 1.3.6.1.4.1.9.9.97.3.2.36
A collection of objects for specifying the router based information while IP multicast flows stored in the hardware switching cache are queried.
OBJECT-GROUP    

cseFlowMcastMgmtGroup2 1.3.6.1.4.1.9.9.97.3.2.37
A collection of objects for enhanced querying of IP multicast flows stored in hardware switching cache.
OBJECT-GROUP    

cseCacheStatisticsGroup 1.3.6.1.4.1.9.9.97.3.2.38
A collection of objects providing switch engine statistics on the flow cache entries.
OBJECT-GROUP    

cseL3SwitchedPktsPerSecGroup 1.3.6.1.4.1.9.9.97.3.2.39
A collection of objects providing switch engine statistics on total number of packets switched per second.
OBJECT-GROUP    

Defined Objects

CiscoGauge64  
This TC describes an object with a nonnegative integer value that may increase or decrease, with a maximum value of 2^64-1.
TEXTUAL-CONVENTION    
  Counter64  

ControlStatus  
This TC describes the current status of a controlled object value.
TEXTUAL-CONVENTION    
  INTEGER enabled(1), disabled(2)  

McastGroupIp  
This TC specifies an multicast group IP address, a class D IP address with the first byte in the range of 224 to 239.
TEXTUAL-CONVENTION    
  IpAddress  

FlowAddressComponent  
Represents a network layer address. The length and format of the address is protocol dependent as follows: ip 6 octets first 4 octets are the IP address in network order last 2 bytes is the transport's port number. ipx 10 octets first 4 octets are the net number last 6 octets are the host number
TEXTUAL-CONVENTION    
  OCTET STRING SIZE(6..6 | 10..10)  

CseL2StatsEntry  
SEQUENCE    
  Counter32 as cseL2ForwardedLocalPkts  
  Counter64 as cseL2ForwardedLocalOctets  
  Counter32 as cseL2ForwardedTotalPkts  
  Counter32 as cseL2NewAddressLearns  
  Counter32 as cseL2AddrLearnFailures  
  Counter32 as cseL2DstAddrLookupMisses  
  Counter32 as cseL2IpPkts  
  Counter32 as cseL2IpxPkts  
  Counter32 as cseL2AssignedProtoPkts  
  Counter32 as cseL2OtherProtoPkts  

CseL2StatsHCEntry  
SEQUENCE    
  Counter32 as cseL2HCOverflowForwardedLocalPkts  
  Counter64 as cseL2HCForwardedLocalPkts  
  Counter32 as cseL2HCOverflowForwardedTotalPkts  
  Counter64 as cseL2HCForwardedTotalPkts  
  Counter32 as cseL2HCOverflowIpPkts  
  Counter64 as cseL2HCIpPkts  
  Counter32 as cseL2HCOverflowIpxPkts  
  Counter64 as cseL2HCIpxPkts  
  Counter32 as cseL2HCOverflowAssignedProtoPkts  
  Counter64 as cseL2HCAssignedProtoPkts  
  Counter32 as cseL2HCOverflowOtherProtoPkts  
  Counter64 as cseL2HCOtherProtoPkts  

CseRouterEntry  
SEQUENCE    
  IpAddress as cseRouterIndex  
  INTEGER as cseRouterFlowMask  
  DisplayString as cseRouterName  
  TruthValue as cseRouterStatic  
  INTEGER as cseRouterIpxFlowMask  

CseStaticExtRouterEntry  
SEQUENCE    
  DisplayString as cseStaticRouterName  
  OwnerString as cseStaticRouterOwner  
  RowStatus as cseStaticRouterStatus  
  BITS as cseStaticRouterType  

CseRouterVlanEntry  
SEQUENCE    
  MacAddress as cseRouterMac  
  VlanIndex as cseRouterVlan  
  BITS as cseRouterProtocol  

CseFlowQueryEntry  
SEQUENCE    
  Unsigned32 as cseFlowQueryIndex  
  INTEGER as cseFlowQueryMask  
  BITS as cseFlowQueryTransport  
  FlowAddressComponent as cseFlowQuerySource  
  FlowAddressComponent as cseFlowQuerySourceMask  
  FlowAddressComponent as cseFlowQueryDestination  
  FlowAddressComponent as cseFlowQueryDestinationMask  
  IpAddress as cseFlowQueryRouterIndex  
  OwnerString as cseFlowQueryOwner  
  Integer32 as cseFlowQueryResultingRows  
  CiscoGauge64 as cseFlowQueryResultTotalPkts  
  CiscoGauge64 as cseFlowQueryResultTotalOctets  
  TimeInterval as cseFlowQueryResultAvgDuration  
  TimeInterval as cseFlowQueryResultAvgIdle  
  RowStatus as cseFlowQueryStatus  
  TimeStamp as cseFlowQueryCreateTime  
  Unsigned32 as cseFlowQueryTotalFlows  
  Integer32 as cseFlowQuerySkipNFlows  

CseFlowDataEntry  
SEQUENCE    
  Unsigned32 as cseFlowDataIndex  
  MacAddress as cseFlowDataSrcMac  
  MacAddress as cseFlowDataDstMac  
  TruthValue as cseFlowDataStaticFlow  
  INTEGER as cseFlowDataEncapType  
  FlowAddressComponent as cseFlowDataSource  
  FlowAddressComponent as cseFlowDataDestination  
  VlanIndex as cseFlowDataDestVlan  
  Integer32 as cseFlowDataIpQOS  
  Integer32 as cseFlowDataIpQOSPolicy  
  TimeStamp as cseFlowDataWhenCreated  
  TimeStamp as cseFlowDataLastUsed  
  Gauge32 as cseFlowDataPkts  
  CiscoGauge64 as cseFlowDataOctets  

CseFlowSwitchControlEntry  
SEQUENCE    
  CiscoNetworkProtocol as cseFlowSwitchProtocol  
  ControlStatus as cseFlowSwitchStatus  

CseFlowMcastQueryEntry  
SEQUENCE    
  Unsigned32 as cseFlowMcastQueryIndex  
  BITS as cseFlowMcastQueryMask  
  IpAddress as cseFlowMcastQuerySrc  
  McastGroupIp as cseFlowMcastQueryGrp  
  VlanIndex as cseFlowMcastQuerySrcVlan  
  IpAddress as cseFlowMcastQueryRtrIndex  
  Integer32 as cseFlowMcastQuerySkipNFlows  
  OwnerString as cseFlowMcastQueryOwner  
  Integer32 as cseFlowMcastQueryTotalFlows  
  Integer32 as cseFlowMcastQueryRows  
  RowStatus as cseFlowMcastQueryStatus  
  TimeStamp as cseFlowMcastQueryCreateTime  
  MplsVpnId as cseFlowMcastQueryMvrf  
  InetAddressType as cseFlowMcastQueryAddrType  
  InetAddress as cseFlowMcastQuerySource  
  InetAddress as cseFlowMcastQueryGroup  

CseFlowMcastResultEntry  
SEQUENCE    
  Integer32 as cseFlowMcastResultIndex  
  McastGroupIp as cseFlowMcastResultGrp  
  IpAddress as cseFlowMcastResultSrc  
  VlanIndex as cseFlowMcastResultSrcVlan  
  IpAddress as cseFlowMcastResultRtrIp  
  MacAddress as cseFlowMcastResultRtrMac  
  TimeStamp as cseFlowMcastResultCreatedTS  
  TimeStamp as cseFlowMcastResultLastUsedTS  
  Counter64 as cseFlowMcastResultPkts  
  Counter64 as cseFlowMcastResultOctets  
  OCTET STRING as cseFlowMcastResultDstVlans  
  OCTET STRING as cseFlowMcastResultDstVlans2k  
  OCTET STRING as cseFlowMcastResultDstVlans3k  
  OCTET STRING as cseFlowMcastResultDstVlans4k  
  MplsVpnId as cseFlowMcastResultMvrf  
  InetAddressType as cseFlowMcastResultAddrType  
  InetAddress as cseFlowMcastResultGroup  
  InetAddress as cseFlowMcastResultSource  
  INTEGER as cseFlowMcastResultFlowType  
  OCTET STRING as cseFlowMcastResultHFlag1k2k  
  OCTET STRING as cseFlowMcastResultHFlag3k4k  

CseStaticIpxExtRouterEntry  
SEQUENCE    
  DisplayString as cseStaticIpxRouterName  
  OwnerString as cseStaticIpxRouterOwner  
  RowStatus as cseStaticIpxRouterStatus  

CseBridgedFlowStatsCtrlEntry  
SEQUENCE    
  VlanIndex as cseBridgedFlowVlan  
  TruthValue as cseFlowBridgedFlowStatsEnable  

CseFlowExcludeEntry  
SEQUENCE    
  CiscoPort as cseFlowExcludePort  
  INTEGER as cseFlowExcludeProtocol  
  RowStatus as cseFlowExcludeStatus  

CseFlowStatsEntry  
SEQUENCE    
  Gauge32 as cseFlowTotalFlows  

CseNetflowLSFilterEntry  
SEQUENCE    
  Unsigned32 as cseNetflowLSFilterIndex  
  FlowAddressComponent as cseNetflowLSFilterDataSource  
  FlowAddressComponent as cseNetflowLSFilterDataSourceMask  
  FlowAddressComponent as cseNetflowLSFilterDataDest  
  FlowAddressComponent as cseNetflowLSFilterDataDestMask  
  Integer32 as cseNetflowLSFilterDataProtocol  
  INTEGER as cseNetflowLSFilterSelection  
  RowStatus as cseNetflowLSFilterStatus  

CseNetflowPerVlanIfCtrlEntry  
SEQUENCE    
  VlanIndex as cseNetflowPerVlanIfCtrlVlan  
  TruthValue as cseNetflowPerVlanIfEnable  

CseL3StatsEntry  
SEQUENCE    
  Counter32 as cseL3SwitchedTotalPkts  
  Counter64 as cseL3SwitchedTotalOctets  
  Counter32 as cseL3CandidateFlowHits  
  Counter32 as cseL3EstablishedFlowHits  
  Gauge32 as cseL3ActiveFlows  
  Counter32 as cseL3FlowLearnFailures  
  Counter32 as cseL3IntFlowInvalids  
  Counter32 as cseL3ExtFlowInvalids  
  Counter32 as cseL3SwitchedPktsPerSec  

CseL3VlanStatsEntry  
SEQUENCE    
  VlanIndex as cseL3VlanIndex  
  Counter64 as cseL3VlanInPkts  
  Counter64 as cseL3VlanInOctets  
  Counter64 as cseL3VlanOutPkts  
  Counter64 as cseL3VlanOutOctets  
  Counter64 as cseL3VlanInUnicastPkts  
  Counter64 as cseL3VlanInUnicastOctets  
  Counter64 as cseL3VlanOutUnicastPkts  
  Counter64 as cseL3VlanOutUnicastOctets  

CseStatsFlowEntry  
SEQUENCE    
  Counter32 as cseStatsFlowAged  
  Counter32 as cseStatsFlowPurged  
  Counter32 as cseStatsFlowParityFail  

CseCacheUtilEntry  
SEQUENCE    
  Gauge32 as cseCacheUtilization  
  Unsigned32 as cseCacheEntriesCreated  
  Unsigned32 as cseCacheEntriesFailed  

CseErrorStatsEntry  
SEQUENCE    
  Counter64 as cseIpPlenErrors  
  Counter64 as cseIpTooShortErrors  
  Counter64 as cseIpCheckSumErrors  
  Counter64 as cseIpxPlenErrors  
  Counter64 as cseIpxTooShortErrors  

CseErrorStatsLCEntry  
SEQUENCE    
  Counter32 as cseLCIpPlenErrors  
  Counter32 as cseLCIpTooShortErrors  
  Counter32 as cseLCIpCheckSumErrors  
  Counter32 as cseLCIpxPlenErrors  
  Counter32 as cseLCIpxTooShortErrors  

CseProtocolFilterPortEntry  
SEQUENCE    
  INTEGER as cseProtocolFilterPortProtocol  
  INTEGER as cseProtocolFilterPortAdminStatus  
  INTEGER as cseProtocolFilterPortOperStatus  

CseUcastCacheEntry  
SEQUENCE    
  Unsigned32 as cseUcastCacheIndex  
  INTEGER as cseUcastCacheFlowType  
  INTEGER as cseUcastCacheTransport  
  FlowAddressComponent as cseUcastCacheDest  
  FlowAddressComponent as cseUcastCacheDestMask  
  FlowAddressComponent as cseUcastCacheSource  
  FlowAddressComponent as cseUcastCacheSrcMask  
  IpAddress as cseUcastCacheRtrIp  
  OwnerString as cseUcastCacheOwner  
  INTEGER as cseUcastCacheResult  
  RowStatus as cseUcastCacheStatus  

CseMcastCacheEntry  
SEQUENCE    
  Unsigned32 as cseMcastCacheIndex  
  INTEGER as cseMcastCacheFlowType  
  McastGroupIp as cseMcastCacheGrp  
  IpAddress as cseMcastCacheSrc  
  IpAddress as cseMcastCacheRtrIp  
  OwnerString as cseMcastCacheOwner  
  INTEGER as cseMcastCacheResult  
  RowStatus as cseMcastCacheStatus  

CseCefFibEntry  
SEQUENCE    
  Unsigned32 as cseCefFibIndex  
  InetAddressType as cseCefFibAddrType  
  InetAddress as cseCefFibDestIp  
  InetAddress as cseCefFibDestIpMask  
  INTEGER as cseCefFibType  

CseCefAdjacencyEntry  
SEQUENCE    
  Unsigned32 as cseCefAdjacencyIndex  
  InetAddressType as cseCefAdjacencyAddrType  
  InetAddress as cseCefAdjacencyNextHopIp  
  MacAddress as cseCefAdjacencyNextHopMac  
  InterfaceIndexOrZero as cseCefAdjacencyNextHopIfIndex  
  INTEGER as cseCefAdjacencyType  
  Counter64 as cseCefAdjacencyPkts  
  Counter64 as cseCefAdjacencyOctets  
  INTEGER as cseCefAdjacencyEncap  
  Unsigned32 as cseCefAdjacencyMTU  

CseTcamUsageEntry  
SEQUENCE    
  INTEGER as cseTcamResourceType  
  SnmpAdminString as cseTcamResourceDescr  
  Unsigned32 as cseTcamResourceUsed  
  Unsigned32 as cseTcamResourceTotal  

CseMetUsageEntry  
SEQUENCE    
  Unsigned32 as cseMetIndex  
  Unsigned32 as cseMetTotalEntries  
  Unsigned32 as cseMetUnallocatedSpcFreeEntries  
  Unsigned32 as cseMetAllocatedSpcFreeEntries