
| SNMPv2-SMI | SNMPv2-CONF | BASIS-MIB |
| CISCOWAN-SMI |
| MODULE-IDENTITY | OBJECT-TYPE | Integer32 |
| Counter32 | MODULE-COMPLIANCE | OBJECT-GROUP |
| bbIfCnf | bbIfCnt | bbIfStateGrp |
| ciscoWan |
| bbIfCnfPortGrp | 1.3.6.1.4.1.351.110.5.2.6.1.1 | ||
| OBJECT IDENTIFIER | |||
| bbIfCnfPortGrpTable | 1.3.6.1.4.1.351.110.5.2.6.1.1.1 | ||
| The Broadband Interface config table is for logical interface. There will an entry for each of the logical partition of the physical line. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| BbIfCnfPortGrpEntry | |||
| bbIfCnfPortGrpEntry | 1.3.6.1.4.1.351.110.5.2.6.1.1.1.1 | ||
| An entry for the logical interface. The interface may be further be configured to be used as a virtual trunk OR as a UNI Port. | |||
| OBJECT-TYPE | |||
| BbIfCnfPortGrpEntry | |||
| bbIfNum | 1.3.6.1.4.1.351.110.5.2.6.1.1.1.1.1 | ||
| This is logical interface number within a physical line num. In MGX PXM1 card, a physical port can have a maximum of 32 logical interfaces. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..32 | ||
| bbIfRowStatus | 1.3.6.1.4.1.351.110.5.2.6.1.1.1.1.2 | ||
| This variable enables or disables the logical interface. 1 - enable 2 - disable 3 - modify | |||
| OBJECT-TYPE | |||
| INTEGER | add(1), del(2), mod(3) | ||
| bbIfAdmin | 1.3.6.1.4.1.351.110.5.2.6.1.1.1.1.3 | ||
| This variable enables or disables the logical interface. 1 - up 2 - down 3 - writeOnly | |||
| OBJECT-TYPE | |||
| INTEGER | up(1), down(2), writeOnly(3) | ||
| bbIfLineNum | 1.3.6.1.4.1.351.110.5.2.6.1.1.1.1.4 | ||
| The line number associated with the logical interface. For PXM1, there is currently 4 physical lines. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..4 | ||
| bbIfIngrPctBandwidth | 1.3.6.1.4.1.351.110.5.2.6.1.1.1.1.5 | ||
| The percentage of aggregate physical line bandwidth, available for this broadband interface - Ingress. Default is 0 %. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..100 | ||
| bbIfEgrPctBandwidth | 1.3.6.1.4.1.351.110.5.2.6.1.1.1.1.6 | ||
| The percentage of aggregate physical line bandwidth, available for this broadband interface - Egress . Default is 0 %. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..100 | ||
| bbIfMinVpi | 1.3.6.1.4.1.351.110.5.2.6.1.1.1.1.7 | ||
| The lower limit of VPI range to be reserved for this logical interface. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..4095 | ||
| bbIfMaxVpi | 1.3.6.1.4.1.351.110.5.2.6.1.1.1.1.8 | ||
| The upper limit of VPI range to be reserved for this logical interface. For virtual trunks, bbIfMinVpi and bbIfMaxVpi should be the same. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..4095 | ||
| bbIfSpeed | 1.3.6.1.4.1.351.110.5.2.6.1.1.1.1.9 | ||
| The speed of the port in cells per second. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| bbIfMaxCellRatePct | 1.3.6.1.4.1.351.110.5.2.6.1.1.1.1.10 | ||
| The maximum cell rate allowed for the port in terms of percentage. Must be greater than or equal to bbIfIngrPctBandwidth. The default is 100 percent. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..100 | ||
| nextBbIfNumAvailable | 1.3.6.1.4.1.351.110.5.2.6.1.1.2 | ||
| Indicates the next logical broadband interface number that is available. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..32 | ||
| bbIfStateGrpTable | 1.3.6.1.4.1.351.110.5.2.6.3.1 | ||
| The state table for the logical interface. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| BbIfStateGrpEntry | |||
| bbIfStateGrpEntry | 1.3.6.1.4.1.351.110.5.2.6.3.1.1 | ||
| An entry for each logical interface representing the state. | |||
| OBJECT-TYPE | |||
| BbIfStateGrpEntry | |||
| bbStateIfNum | 1.3.6.1.4.1.351.110.5.2.6.3.1.1.1 | ||
| This is logical interface number within a physical line num. In MGX PXM1 card, a physical port can have a maximum of 32 logical interfaces. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..32 | ||
| bbIfState | 1.3.6.1.4.1.351.110.5.2.6.3.1.1.2 | ||
| This variable indicates the status of the logical interface. The following values are not supported for the logical interface. remoteloopback (3), outofcelldelineation (6), localloopback (7). | |||
| OBJECT-TYPE | |||
| INTEGER | notConfigured(1), active(2), linefailure(4), signallingfailure(5), inactive(6), lineinloopback(7) | ||
| bbIfOversubscribed | 1.3.6.1.4.1.351.110.5.2.6.3.1.1.3 | ||
| This variable indicates the whether the logical interface is over subscribed or not. | |||
| OBJECT-TYPE | |||
| INTEGER | false(1), true(2) | ||
| bbIfIngrPercentUtil | 1.3.6.1.4.1.351.110.5.2.6.3.1.1.4 | ||
| Percentage Utilization of the interface in the Ingress direction. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..1000 | ||
| bbIfEgrPercentUtil | 1.3.6.1.4.1.351.110.5.2.6.3.1.1.5 | ||
| Percentage Utilization of the interface in the Egress direction. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..1000 | ||
| bbIfCntGrp | 1.3.6.1.4.1.351.110.5.2.6.4.1 | ||
| OBJECT IDENTIFIER | |||
| bbIfCntGrpTable | 1.3.6.1.4.1.351.110.5.2.6.4.1.1 | ||
| The Broadband Interface Count table is for logical interface. There will an entry for each of the logical partition of the physical line. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| BbIfCntGrpEntry | |||
| bbIfCntGrpEntry | 1.3.6.1.4.1.351.110.5.2.6.4.1.1.1 | ||
| An entry for logical interface. | |||
| OBJECT-TYPE | |||
| BbIfCntGrpEntry | |||
| bbCntIfNum | 1.3.6.1.4.1.351.110.5.2.6.4.1.1.1.1 | ||
| Refers to the logical interface index. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..32 | ||
| bbIfTotalCells | 1.3.6.1.4.1.351.110.5.2.6.4.1.1.1.2 | ||
| Total number of cells (VC plus Qbin) that belong to this Interface. This maps on to the virtual interface of QE. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| bbIfRcvValidOAMCells | 1.3.6.1.4.1.351.110.5.2.6.4.1.1.1.3 | ||
| Total number of OAM cell received. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| bbIfRcvRmCells | 1.3.6.1.4.1.351.110.5.2.6.4.1.1.1.4 | ||
| Total number of RM cells Received. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| bbIfRcvClp0Cells | 1.3.6.1.4.1.351.110.5.2.6.4.1.1.1.5 | ||
| Total number of CLP-0 cells Received. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| bbIfRcvClp1Cells | 1.3.6.1.4.1.351.110.5.2.6.4.1.1.1.6 | ||
| Total number of CLP-1 cells Received. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| bbIfRcvClp0DiscCells | 1.3.6.1.4.1.351.110.5.2.6.4.1.1.1.7 | ||
| Total number of CLP-0 cells discarded at Ingress. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| bbIfRcvClp1DiscCells | 1.3.6.1.4.1.351.110.5.2.6.4.1.1.1.8 | ||
| Total number of CLP-1 cells discarded at Ingress. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| bbIfXmtOAMCells | 1.3.6.1.4.1.351.110.5.2.6.4.1.1.1.9 | ||
| Total number of OAM cells transmitted. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| bbIfXmtRmCells | 1.3.6.1.4.1.351.110.5.2.6.4.1.1.1.10 | ||
| Total number of RM cells transmitted. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| bbIfXmtClp0Cells | 1.3.6.1.4.1.351.110.5.2.6.4.1.1.1.11 | ||
| Total number of CLP-0 cells transmitted. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| bbIfXmtClp1Cells | 1.3.6.1.4.1.351.110.5.2.6.4.1.1.1.12 | ||
| Total number of CLP-1 cells transmitted. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| bbIfCntClrButton | 1.3.6.1.4.1.351.110.5.2.6.4.1.1.1.13 | ||
| Writing a value of 2 resets all the counters. | |||
| OBJECT-TYPE | |||
| INTEGER | noAction(1), resetCounter32s(2) | ||
| bbIfRcvErroredCells | 1.3.6.1.4.1.351.110.5.2.6.4.1.1.1.14 | ||
| Total number of cells with Invalid VPI VCI or Invalid PTI fields This is a card level counter and hence will be the same for all instances of the ports. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| ciscoWanBbifPortMIB | 1.3.6.1.4.1.351.150.32 | ||
| The MIB module for configuration of ATM logical ports in PXM1 Service module in MGX82xx series. This MIB contains information on ATM Logical port statistics. | |||
| MODULE-IDENTITY | |||
| cwbPortMIBConformance | 1.3.6.1.4.1.351.150.32.2 | ||
| OBJECT IDENTIFIER | |||
| cwbPortMIBGroups | 1.3.6.1.4.1.351.150.32.2.1 | ||
| OBJECT IDENTIFIER | |||
| cwbPortGenearlGroup | 1.3.6.1.4.1.351.150.32.2.1.1 | ||
| The collection of objects which are applicable for general information about logical ports. | |||
| OBJECT-GROUP | |||
| cwbPortConfGroup | 1.3.6.1.4.1.351.150.32.2.1.2 | ||
| The collection of objects which are used for configuring ATM logical ports(known as broad band interface ports). | |||
| OBJECT-GROUP | |||
| cwbPortStateGroup | 1.3.6.1.4.1.351.150.32.2.1.3 | ||
| The collection of objects which are used for finding the state of ATM logical ports(known as broad band interface ports). | |||
| OBJECT-GROUP | |||
| cwbPortStatsGroup | 1.3.6.1.4.1.351.150.32.2.1.4 | ||
| The collection of objects containing the statistics information for ATM Logical ports. | |||
| OBJECT-GROUP | |||
| cwbPortMIBCompliances | 1.3.6.1.4.1.351.150.32.2.2 | ||
| OBJECT IDENTIFIER | |||
| cwbPortCompliance | 1.3.6.1.4.1.351.150.32.2.2.1 | ||
| The compliance statement for objects related to SRM MIB. | |||
| MODULE-COMPLIANCE | |||
| BbIfCnfPortGrpEntry | |||
| SEQUENCE | |||
| Integer32 as bbIfNum | |||
| INTEGER as bbIfRowStatus | |||
| INTEGER as bbIfAdmin | |||
| Integer32 as bbIfLineNum | |||
| Integer32 as bbIfIngrPctBandwidth | |||
| Integer32 as bbIfEgrPctBandwidth | |||
| Integer32 as bbIfMinVpi | |||
| Integer32 as bbIfMaxVpi | |||
| Integer32 as bbIfSpeed | |||
| Integer32 as bbIfMaxCellRatePct | |||
| BbIfStateGrpEntry | |||
| SEQUENCE | |||
| INTEGER as bbStateIfNum | |||
| INTEGER as bbIfState | |||
| INTEGER as bbIfOversubscribed | |||
| INTEGER as bbIfIngrPercentUtil | |||
| INTEGER as bbIfEgrPercentUtil | |||
| BbIfCntGrpEntry | |||
| SEQUENCE | |||
| INTEGER as bbCntIfNum | |||
| Counter32 as bbIfTotalCells | |||
| Counter32 as bbIfRcvValidOAMCells | |||
| Counter32 as bbIfRcvRmCells | |||
| Counter32 as bbIfRcvClp0Cells | |||
| Counter32 as bbIfRcvClp1Cells | |||
| Counter32 as bbIfRcvClp0DiscCells | |||
| Counter32 as bbIfRcvClp1DiscCells | |||
| Counter32 as bbIfXmtOAMCells | |||
| Counter32 as bbIfXmtRmCells | |||
| Counter32 as bbIfXmtClp0Cells | |||
| Counter32 as bbIfXmtClp1Cells | |||
| INTEGER as bbIfCntClrButton | |||
| Counter32 as bbIfRcvErroredCells | |||