
CISCO-WAN-CES-PORT-MIB
File:
CISCO-WAN-CES-PORT-MIB.mib (15472 bytes)
Imported modules
Imported symbols
Defined Objects
| cesmPort |
1.3.6.1.4.1.351.110.5.3.1 |
| OBJECT IDENTIFIER |
|
|
|
| cesmPortCnfGrpTable |
1.3.6.1.4.1.351.110.5.3.1.1.1 |
| The config table is for CES logical port. This is used for configuring the port type and number of DS0s and number of Subcircuits in DS0 on the CES port. |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
CesmPortCnfGrpEntry |
|
| cesmPortCnfGrpEntry |
1.3.6.1.4.1.351.110.5.3.1.1.1.1 |
| An entry for each logical port. Each entry contains information on the port type, DS0s configured and number of DS0 subcircuits. |
| OBJECT-TYPE |
|
|
|
| |
CesmPortCnfGrpEntry |
|
|
| cesPortNum |
1.3.6.1.4.1.351.110.5.3.1.1.1.1.1 |
| This object identifies the logical port number. The range support depends upon the type of the service module(Card). - 8 port T1 Card, range is 1..192. - 8 port E1 Card, range is 1..248. - 1 port T3 Card, range is 1..1. Range is caclulated as follows. This can be used for calculating the range for other type of cards. For T1 Card: (24 * Number of T1 Ports) For E1 Card: (31 * Number of E1 Ports). |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
1..2048 |
|
| cesPortRowStatus |
1.3.6.1.4.1.351.110.5.3.1.1.1.1.2 |
| This variable enables or modifies the port 1 - add : Add a logical port 2 - del : Delete a logical port 3 - mod : Modify a logical port. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
add(1), del(2), mod(3) |
|
| cesPortLineNum |
1.3.6.1.4.1.351.110.5.3.1.1.1.1.3 |
| This object represents the line number to which this port is associated. The supported range depends upon the type of service module(card). |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
1..128 |
|
| cesPortType |
1.3.6.1.4.1.351.110.5.3.1.1.1.1.4 |
| This object represents port type whether it is carrying subrate circuits. structured : This is for SDT(Structured Data Transfer). This type of port supports following features: * intended to emulate point-to-point fractional DS1 or E1 circuit. * Synchronous timing * Fractional(Nx64 Kbps)DS1/E1 service (Contiguous timeslots only).You can map an Nx64 Kbps channel to any Virtual Channel(VC). unstructured : This is for unstructured data transfer(UDT) All the DS0 time slots are allocated. This type of port supports following features: * intended to emulate point-to-point DS1 or E1 circuit. * Synchronous and Asynchronous timing framingOnVcDisconnect : similar to unstructured during normal operation. In case of channel failure line data will be looped back towards line. strau : only one DS0 time slot is allocated. The value strau(4) value is not supported in CESM-8T1/E1 or CESM-T3E3. CESM-T3E3 card supports value unstructured(2) only. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
structured(1), unstructured(2), framingOnVcDisconnect(3), strau(4) |
|
| cesPortNumOfDs0Slot |
1.3.6.1.4.1.351.110.5.3.1.1.1.1.6 |
| This represents number of DS0 time slots configured to this Port. If the cesPortType is strau(4), then this can not have more than 1 DS0 time slot. |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
1..32 |
|
| cesPortNumOfSCIPerDS0 |
1.3.6.1.4.1.351.110.5.3.1.1.1.1.7 |
| This object represents number of subcircuit in the DS0 time slot. This is applicable only when cesPortType is strau(4). 8 = there are 8 no .of 8kbps links (1 bit) 4 = there are 4 no .of 16kbps links (2 bit) 2 = there are 2 no .of 32kbps links (4 bit) Currently not supported in CESM-8. |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
1..8 |
|
| cesPortSpeed |
1.3.6.1.4.1.351.110.5.3.1.1.1.1.8 |
| This object identifies the configured speed of port. Max speed for T1 = 1544 Max speed for E1 = 2038 Max speed for T3 = 44736 Max speed for E3 = 34368. |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..44736 |
|
| cesPortState |
1.3.6.1.4.1.351.110.5.3.1.1.1.1.9 |
| This variable indicates the state of the logical port. The possible values are : notConfigured (1) : Port is not configured active (2) : Port is in active state remoteLoopback (3) : Remote Loopback is set failedDueToLine(4) : Port failed due to some failure in physical line failedDueToSignalling(5) : Port failed due to some Signalling issues. inactive (6) : Port is not active inBert (7) : Bit Error Rate Test(BERT) in progress. farEndRemoteLoopback(8): Far End is in loopback. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
notConfigured(1), active(2), remoteLoopback(3), failedDueToLine(4), failedDueToSignalling(5), inactive(6), inBert(7), farEndRemoteLoopback(8) |
|
| cesPortBERTEnable |
1.3.6.1.4.1.351.110.5.3.1.1.1.1.10 |
| This variable enables/disables BERT. This object is not supported in CESM-T3E3. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
disable(1), enable(2) |
|
| cesPortNextAvailable |
1.3.6.1.4.1.351.110.5.3.1.1.2 |
| This variable contains the next UNUSED logical port number of the possible 32 DS0s * n ports. This number can be used in channel config table, the cesportNextAvailable gets updated if the number gets used to create a logical port. A '0' indicates that no more ports are available. |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..2048 |
|
| cesPortsUsedLine1 |
1.3.6.1.4.1.351.110.5.3.1.1.3 |
| Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1 This is for line 1 |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..'ffffff'h |
|
| cesPortsUsedLine2 |
1.3.6.1.4.1.351.110.5.3.1.1.4 |
| Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1 This is for line 2. |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..'ffffff'h |
|
| cesPortsUsedLine3 |
1.3.6.1.4.1.351.110.5.3.1.1.5 |
| Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1 This is for line 3 |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..'ffffff'h |
|
| cesPortsUsedLine4 |
1.3.6.1.4.1.351.110.5.3.1.1.6 |
| Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1. This is for line 4 |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..'ffffff'h |
|
| cesPortsUsedLine5 |
1.3.6.1.4.1.351.110.5.3.1.1.7 |
| Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1 This is for line 5 |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..'ffffff'h |
|
| cesPortsUsedLine6 |
1.3.6.1.4.1.351.110.5.3.1.1.8 |
| Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1 This is for line 6 |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..'ffffff'h |
|
| cesPortsUsedLine7 |
1.3.6.1.4.1.351.110.5.3.1.1.9 |
| Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1 This is for line 7 |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..'ffffff'h |
|
| cesPortsUsedLine8 |
1.3.6.1.4.1.351.110.5.3.1.1.10 |
| Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1 This is for line 8 |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..'ffffff'h |
|
Defined Objects
| CesmPortCnfGrpEntry |
|
| SEQUENCE |
|
|
|
| |
Integer32 as cesPortNum |
|
|
| |
INTEGER as cesPortRowStatus |
|
|
| |
Integer32 as cesPortLineNum |
|
|
| |
INTEGER as cesPortType |
|
|
| |
Integer32 as cesPortDs0ConfigBitMap |
|
|
| |
Integer32 as cesPortNumOfDs0Slot |
|
|
| |
Integer32 as cesPortNumOfSCIPerDS0 |
|
|
| |
Integer32 as cesPortSpeed |
|
|
| |
INTEGER as cesPortState |
|
|
| |
INTEGER as cesPortBERTEnable |
|
|