
CISCO-WAN-SRM-MIB
File:
CISCO-WAN-SRM-MIB.mib (10176 bytes)
Imported modules
Imported symbols
Defined Objects
| srm3T3CnfGrpEntry |
1.3.6.1.4.1.351.110.3.10.1.1 |
| an entry in the T3 configuration table |
| OBJECT-TYPE |
|
|
|
| |
Srm3T3CnfGrpEntry |
|
|
| srmT1RowStatus |
1.3.6.1.4.1.351.110.3.10.1.1.3 |
| a command is used to add, delete, or modify one or more DS1 mapping. Default value is delete. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
add(1), delete(2), modify(3) |
|
| srmTargetSlotNum |
1.3.6.1.4.1.351.110.3.10.1.1.4 |
| specify the target slot number to be linked. There is no default value for this object. For MGX8850: SRM01 services slots 1 - 6 and 9 - 14, SRM02 services slots 17 - 22 and 25 - 30 For MGX8220: SYNTAX Integer32 (5 ..14) |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
1..32 |
|
| srmeCnfGrp |
1.3.6.1.4.1.351.110.3.22 |
| OBJECT IDENTIFIER |
|
|
|
| srmeCnfGrpEntry |
1.3.6.1.4.1.351.110.3.22.1.1 |
| an entry in the SRME Distribution configuration table |
| OBJECT-TYPE |
|
|
|
| |
SrmeCnfGrpEntry |
|
|
| srmeLineNum |
1.3.6.1.4.1.351.110.3.22.1.1.1 |
| This object identifies the SRME line number. For OC3/STM1: SYNTAX Integer32 1 There is no default value for this object. |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
1..3 |
|
| srmeStartVtNum |
1.3.6.1.4.1.351.110.3.22.1.1.2 |
| The start T1 or E1 number (virtual tributary) to be affected. For OC3 with T1 tributaries: SYNTAX Integer32 (1 .. 84) For STM1 with E1 tributaries: SYNTAX Integer32 (1 .. 63) There is no default value for this object. |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
1..84 |
|
| srmeRowStatus |
1.3.6.1.4.1.351.110.3.22.1.1.3 |
| Command used to add, delete, or modify one or more T1 or E1 mappings. Only the srmeVtFramingType object can be modified once the distribution link is added. To modify all other objects, user should first delete the link and add it again. Default value is modify(3). |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
add(1), delete(2), modify(3) |
|
| srmeVtFramingType |
1.3.6.1.4.1.351.110.3.22.1.1.6 |
| Specifies the Framing Type of the target slot line. This is applicable only if the target module is a T1 Service Module and byte sync mapping is used on SRME. Not applicable to E1 Service Modules. sf: Superframe or D4 esf: Extended Superframe. Default is 'esf' if SRME lines are configured for byte-synchronous mapping, Else, the default is notApplicable. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
notApplicable(1), sf(2), esf(3) |
|
| ciscoWanSrmMIB |
1.3.6.1.4.1.351.150.30 |
| The MIB module for configuration of bulk distribution (de-multiplexing of traffic from higher-bandwidth to lower-bandwidth interfaces). This is used for configuring bulk distribution of T3 interfaces on T1 modules supported in MGX82xx series. Some of the T1 modules are AUSM, FRSM,CESM. This MIB module also contains info. on configuring bulk distribution of SONET interfaces(VT interfaces) on T1 Modules. SRM - Service Resource Module SRME - Service Resource Module Enhanced. |
| MODULE-IDENTITY |
|
|
|
Defined Objects
| Srm3T3CnfGrpEntry |
|
| SEQUENCE |
|
|
|
| |
Integer32 as srmT3LineNum |
|
|
| |
Integer32 as srmStartT1LineNum |
|
|
| |
INTEGER as srmT1RowStatus |
|
|
| |
Integer32 as srmTargetSlotNum |
|
|
| |
Integer32 as srmTargetSlotLineNum |
|
|
| SrmeCnfGrpEntry |
|
| SEQUENCE |
|
|
|
| |
Integer32 as srmeLineNum |
|
|
| |
Integer32 as srmeStartVtNum |
|
|
| |
INTEGER as srmeRowStatus |
|
|
| |
Integer32 as srmeTargetSlotNum |
|
|
| |
Integer32 as srmeTargetSlotLineNum |
|
|
| |
INTEGER as srmeVtFramingType |
|
|