
CNT245-MIB
File:
CNT245-MIB.mib (15555 bytes)
Imported modules
Imported symbols
Defined Objects
| cnt2CompressionEntry |
1.3.6.1.4.1.333.2.4.5.1.1 |
| An instance of a compression/decompression. |
| OBJECT-TYPE |
|
|
|
| |
Cnt2CompressionEntry |
|
|
| cnt2BytesToCompress |
1.3.6.1.4.1.333.2.4.5.1.1.3 |
| The number of bytes submitted to the engine for compression. This value will include all bytes submitted whether or not compression was successful. This value will always be equal or larger than cnt2CompressedBytes. |
| OBJECT-TYPE |
|
|
|
| |
Counter64 |
|
|
| cnt2CompressedBytes |
1.3.6.1.4.1.333.2.4.5.1.1.4 |
| The number of bytes received from the engine after compression. This value will include all of the bytes received from the engine whether or not compres- sion was successful, since the engine returns the initial size in any unsucces- sful attempt at compression. This value will be equal or smaller than cnt2BytesToCompress. |
| OBJECT-TYPE |
|
|
|
| |
Counter64 |
|
|
| cnt2BytesToDecompress |
1.3.6.1.4.1.333.2.4.5.1.1.5 |
| The number of bytes submitted to the engine for decompression. This value will include all bytes submitted whether or not decompression was successful. This value will always be equal or smaller than cnt2DecompressedBytes. |
| OBJECT-TYPE |
|
|
|
| |
Counter64 |
|
|
| cnt2DecompressedBytes |
1.3.6.1.4.1.333.2.4.5.1.1.6 |
| The number of bytes received from the engine after decompression. This value will include all of the bytes received from the engine whether or not decompres- sion was successful, since the engine returns the initial size in any unsucces- sful attempt at decompression. This value will be equal or larger than cnt2BytesToDecompress. |
| OBJECT-TYPE |
|
|
|
| |
Counter64 |
|
|
| cnt2ifCompressionEntry |
1.3.6.1.4.1.333.2.4.5.3.1 |
| An interface entry using compression/ decompression. |
| OBJECT-TYPE |
|
|
|
| |
Cnt2ifCompressionEntry |
|
|
| cnt2ifCompressedOctets |
1.3.6.1.4.1.333.2.4.5.3.1.3 |
| The number of bytes that were compressed out of the transmitted data stream. To calculate the compression ratio for trans- mitted data, the following calculation would be used: ifOutOctets + cnt2ifCompressedOctets ------------------------------------ ifOutOctets. to calculate the overall compression for this interface, the following calculation would be used: ifOutOctets + cnt2ifCompressedOctets + cnt2ifDecompressedOctets + ifInOctets -------------------------------------- ifOutOctets + ifInOctets. |
| OBJECT-TYPE |
|
|
|
| |
Counter64 |
|
|
| cnt2ifCompressionRatio |
1.3.6.1.4.1.333.2.4.5.3.1.4 |
| The Compression ratio for this index. The value is represent of 1 to xx.xx Compression Ratio. Example: Ratio of 1:15.82 would have this set to a value of 1582. The internal Calculation is done as: 100 * (ifOutOctets + cnt2ifCompressedOctets) --------------------------------------------- ifOutOctets Then the result is mod by 100 for floating point. This OID gets created dynamically when there is a compression circuit active. |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| cnt2ifDecompressionEntry |
1.3.6.1.4.1.333.2.4.5.4.1 |
| An interface entry using decompression. |
| OBJECT-TYPE |
|
|
|
| |
Cnt2ifDecompressionEntry |
|
|
| cnt2ifDecompressedOctets |
1.3.6.1.4.1.333.2.4.5.4.1.3 |
| The number of bytes that were compressed out of the received data stream. To calculate the compression ratio for received data, the following calculation would be used: ifInOctets + cnt2ifDeCompressedOctets ------------------------------------- ifInOctets to calculate the overall compression for this interface, the following calculation would be used: ifOutOctets + cnt2ifCompressedOctets + cnt2ifDecompressedOctets + ifInOctets -------------------------------------- ifOutOctets + ifInOctets. |
| OBJECT-TYPE |
|
|
|
| |
Counter64 |
|
|
| cnt2ifDecompressionRatio |
1.3.6.1.4.1.333.2.4.5.4.1.4 |
| The Decompression ratio for this index. The value is represent 1 to xx.xx decompression Ratio. Example: Ratio of 13.82 :1 would have this set to a value of 1382. The internal Calculation is done as: 100 * (ifInOctets + cnt2ifDeCompressedOctets) --------------------------------------------- ifInOctets Then the result is mod by 100 for floating point. This OID gets created dynamically when there is a decompression circuit active. |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
Defined Objects
| Cnt2CompressionEntry |
|
| SEQUENCE |
|
|
|
| |
Integer32 as cnt2CompressionSlotIndex |
|
|
| |
Integer32 as cnt2CompressionIndex |
|
|
| |
Counter64 as cnt2BytesToCompress |
|
|
| |
Counter64 as cnt2CompressedBytes |
|
|
| |
Counter64 as cnt2BytesToDecompress |
|
|
| |
Counter64 as cnt2DecompressedBytes |
|
|
| Cnt2ifCompressionEntry |
|
| SEQUENCE |
|
|
|
| |
Integer32 as cnt2ifCompressionSlotIndex |
|
|
| |
Integer32 as cnt2ifCompressionIndex |
|
|
| |
Counter64 as cnt2ifCompressedOctets |
|
|
| |
Integer32 as cnt2ifCompressionRatio |
|
|
| Cnt2ifDecompressionEntry |
|
| SEQUENCE |
|
|
|
| |
Integer32 as cnt2ifDecompressionSlotIndex |
|
|
| |
Integer32 as cnt2ifDecompressionIndex |
|
|
| |
Counter64 as cnt2ifDecompressedOctets |
|
|
| |
Integer32 as cnt2ifDecompressionRatio |
|
|