COM21-HCXSTU-MIB

File: COM21-HCXSTU-MIB.mib (69327 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC RFC1155-SMI
COM21-HCX-MIB COM21-HCXALM-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
Integer32 IpAddress Gauge32
DisplayString MacAddress Gauge
com21 com21Hcx com21Traps
hcxAlmSeverity hcxEventLogTime

Defined Objects

com21HcxStu 1.3.6.1.4.1.1141.2.50
This is the Com21 ComPort Control MIB module. All data defined in this MIB is held upon the ComController. COM21 Part# 005-0025-00
MODULE-IDENTITY    

com21HcxStuStatusGroup 1.3.6.1.4.1.1141.2.51
OBJECT IDENTIFIER    

com21HcxStuStatusTable 1.3.6.1.4.1.1141.2.51.1
.
OBJECT-TYPE    
  SEQUENCE OF  
    HcxStuStatusEntry

com21HcxStuStatusEntry 1.3.6.1.4.1.1141.2.51.1.1
.
OBJECT-TYPE    
  HcxStuStatusEntry  

hcxStuStatusMacAddr 1.3.6.1.4.1.1141.2.51.1.1.1
Contains IEEE 802 medium access control address of the ComPort device.
OBJECT-TYPE    
  MacAddress  

hcxStuConfigured 1.3.6.1.4.1.1141.2.51.1.1.2
This attribute defines the configured state of the ComPort. This value will be set to true when the NMAPS creates a new entry. If this value is false, the hcxStuAcquired attribute is false and the hcxStuAuthorized flag is set to deauthorized then the entry shall be deleted. Note that this value cannot be set to false if the hcxStuAuthorized flag is set to true.
OBJECT-TYPE    
  INTEGER true(1), false(2)  

hcxStuAcquired 1.3.6.1.4.1.1141.2.51.1.1.3
This attribute defines the acquired state of the ComPort. Note that is state is set once an ComPort can be managed. We could have a condition were an ComPort is acquired but full service cannot be provided. In that case the hcxStuAcqFailInfo attribute shall indicate a problem. If an unknown ComPort is acquired then an entry is created with this value set to true and both hcxStuAuthorized and hcxStuConfigured set to false.
OBJECT-TYPE    
  INTEGER true(1), false(2)  

hcxStuAcqFailInfo 1.3.6.1.4.1.1141.2.51.1.1.4
This attribute provides secondary information related to an ComPort acquisition. If there is a failure in the system that prevents a user from receiving full service, then it will be indicated by this attribute. If an ComPort is unacquired or no problems were encountered then this attribute shall equal noFailure.
OBJECT-TYPE    
  INTEGER noFailure(1), vlanFailure(2), servGrpInvalid(3), bandwidthUnavail(4), unauthorized(5)  

hcxStuAuthorized 1.3.6.1.4.1.1141.2.51.1.1.5
This attribute defines the verified state of the ComPort. This state can only be set by the NMAPS. If this attribute is false, then all cells rates shall be set to 0 on the appropriate Ethernet and RF Receiver cards.
OBJECT-TYPE    
  INTEGER true(1), false(2)  

hcxStuLedFlashTest 1.3.6.1.4.1.1141.2.51.1.1.6
Used to invoke an ComPort LED test. Setting the the attribute to start will invoke test. Setting to stop will terminate the test. When reading this attribute, nil shall be returned if no test is active and start if the test is in progress.
OBJECT-TYPE    
  INTEGER nil(1), start(2), stop(3)  

hcxStuUpstreamTest 1.3.6.1.4.1.1141.2.51.1.1.7
Used to invoke an ComPort Upstream RF test. Setting the attribute to start will invoke test. Setting to stop will terminate the test. When reading this attribute, nil shall be returned if no test is active and start if the test is in progress. Note that the hcxStuUpstrmTestFreq shall be validated before initiating the test.
OBJECT-TYPE    
  INTEGER nil(1), start(2), stop(3)  

hcxStuVlanId 1.3.6.1.4.1.1141.2.51.1.1.8
This attribute defines the virtual LAN id associated with the ComPort. No default, must be set. Note, in the case of an acquired but unconfigured ComPort, a value of 0 will be returned.
OBJECT-TYPE    
  INTEGER 1..64  

hcxStuRxShelfId 1.3.6.1.4.1.1141.2.51.1.1.9
This attribute specifies the shelf id associated with the RX the ComPort is currently assigned to. If ComPort is unacquired then the value shall be 0.
OBJECT-TYPE    
  INTEGER 0..2  

hcxStuRxSlotId 1.3.6.1.4.1.1141.2.51.1.1.10
This attribute specifies the slot id of the RX card to which the ComPort is currently assigned. If ComPort is unacquired then the value shall be 0.
OBJECT-TYPE    
  INTEGER 0..10  

hcxStuRxPortId 1.3.6.1.4.1.1141.2.51.1.1.11
This attribute specifies the RX port to which the ComPort is assigned. Presently only one port supported. If the ComPort is unacquired then the attribute shall be set to 0.
OBJECT-TYPE    
  INTEGER 0..1  

hcxStuServiceType 1.3.6.1.4.1.1141.2.51.1.1.12
This attribute defines the Service Type associated with the ComPort. This equals the associated hcxServiceTypeId attribute. The default shall be 0, indicating no assigned service type.
OBJECT-TYPE    
  Integer32  

hcxStuConfSwImage 1.3.6.1.4.1.1141.2.51.1.1.14
Contains the configured software image to be downloaded to the ComPort. The Common Controller download process shall check this value when a download is requested. If this image does not support the hardware specified by the ComPort then an incompatible software version trap shall be generated. It is then up to the user to correct this field. When this field is set, the agent shall check if there is an image of the specified type loaded. If this is not the case then a unavailable software version trap shall be generated. Again, it is the responsibility of the user to ensure that the required image is downloaded. The image identifier shall be represented by 4 numbers deliminated by periods. i.e. a.b.c.d. Each number shall have a value between 0 and 255. This allows storage within a single (four byte) word.
OBJECT-TYPE    
  DisplayString SIZE(16)  

hcxStuPingTestAction 1.3.6.1.4.1.1141.2.51.1.1.15
Used to invoke a ping of the ComPort. Sends an OAM Ping message. When the user reads this attribute a nil response shall be given if no test is active and execute shall be return if a test is active.
OBJECT-TYPE    
  INTEGER nil(1), execute(2)  

hcxStuPingTestResult 1.3.6.1.4.1.1141.2.51.1.1.16
contains result of last ping test. invalid is returned if ping test cannot be run. Examples being an unacquired ComPort or a ComPort.
OBJECT-TYPE    
  INTEGER inprogress(1), success(2), failure(3)  

hcxStuEthTestAction 1.3.6.1.4.1.1141.2.51.1.1.17
This attribute is used to invoke the ComPort Ethernet test. If lpBkTest is selected, the ComController will place the ComPort in the loopback state, transmit a number of ethernet packets and validate the returned packets. hcxStuEthLpbkTestUpRate and hcxStuEthLpbkTestLatency attributes contain the Rate and Latency for the upstream path If dnStrmTest is selected, the ComController will transmit a number of ethernet packets and calculate the downstream rate. hcxStuEthTestDnRate attribute will contain the rate for the downstream path.
OBJECT-TYPE    
  INTEGER nil(1), lpBkTest(2), dnStrmTest(3)  

hcxStuEthTestResult 1.3.6.1.4.1.1141.2.51.1.1.18
This attribute contains the result of the last ComPort test.
OBJECT-TYPE    
  INTEGER inprogress(1), success(2), noResponse(3), corruptPacket(4)  

hcxStuRetPathSelect 1.3.6.1.4.1.1141.2.51.1.1.19
This attribute specifies the return path mode of the ComPort. Default is two way cable.
OBJECT-TYPE    
  INTEGER twoWay(1), teleRet(2)  

hcxStuEth8022Filter 1.3.6.1.4.1.1141.2.51.1.1.20
This attribute is used to control the filtering of 802.2 Ethernet packets for a specific ComPORT. When this is enabled (true), all Ethernet packets of this type shall be dropped. Default is true.
OBJECT-TYPE    
  INTEGER true(1), false(2)  

hcxStuDnstrmFwdCntrl 1.3.6.1.4.1.1141.2.51.1.1.21
This attribute is used to control the forwarding of packets downstream which where received in the upstream from a specific ComPORT. If set to true, then the data will NOT be forwarded downstream but out the WAN interface only. Default is true. Not that the logic here is reversed when compared to the hcxVlanPeerToPeerFlag attribute in the VLAN group.
OBJECT-TYPE    
  INTEGER true(1), false(2)  

hcxStuStatsCollect 1.3.6.1.4.1.1141.2.51.1.1.22
This attribute is used to control whether statistics are collected periodically from the ComPort. Default is enable for two-way ComPorts and disable for ComPorts configured for telephone return operation.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hcxStuPowerRangeState 1.3.6.1.4.1.1141.2.51.1.1.23
This attribute describes the power ranging state of the ComPort. An unacquired ComPort or one operating within the power specifications shall have a state of noProblem.
OBJECT-TYPE    
  INTEGER noProblem(1), powerLow(2), powerHigh(3)  

hcxStuRpmIPortId 1.3.6.1.4.1.1141.2.51.1.1.24
This attribute specifies the RPM I-Port to which the ComPort is associated. 0 will be reported if the ComPort has never been acquired or is not connected via an RPM. The last known I-Port will be reported if the ComPort is unacquired but have been acquired previously.
OBJECT-TYPE    
  INTEGER 0..8  

hcxStuEthLpbkTestUpRate 1.3.6.1.4.1.1141.2.51.1.1.25
This attribute contains the rate recorded for the last loopback test. Will be 0 if test failed.
OBJECT-TYPE    
  Integer32  

hcxStuEthLpbkTestLatency 1.3.6.1.4.1.1141.2.51.1.1.26
This attribute contains the round trip packet latency recorded by the last loopback test. Again 0 if test failed.
OBJECT-TYPE    
  Integer32  

hcxStuModelName 1.3.6.1.4.1.1141.2.51.1.1.27
This attribute defines the ComPort Model Type read from the ComPort. Prior to the acquisition of the ComPort for the first time, this attribute will be uninitialized. Invalid will be set if the model number is not recongnized.
OBJECT-TYPE    
  INTEGER uninitialized(1), invalid(2), cp1000(3), cp1000A(4), cp1000B(5), cp1000C(6), cp1000D(7), cp1100(8), cp1100A(9), cp1100B(10), cp1100C(11), cp1100D(12), cp2000(13), cp2000A(14), cp2100(15), cp2100A(16), cp5020(17), cp5120(18)  

hcxStuEthTestDnRate 1.3.6.1.4.1.1141.2.51.1.1.28
This attribute contains the downstream rate (in bps) recorded by the last hcxStuEthTestAction test. 0 if test failed.
OBJECT-TYPE    
  Integer32  

hcxStuEthLpbkTestDuration 1.3.6.1.4.1.1141.2.51.1.1.30
This attribute specifies the duration of the loopback test in seconds. Default is 5 seconds.
OBJECT-TYPE    
  INTEGER 5..80  

com21HcxStuSrcIpAddrGroup 1.3.6.1.4.1.1141.2.52
OBJECT IDENTIFIER    

com21HcxStuSrcIpAddrTable 1.3.6.1.4.1.1141.2.52.1
.
OBJECT-TYPE    
  SEQUENCE OF  
    HcxStuSrcIpAddrEntry

com21HcxStuSrcIpAddrEntry 1.3.6.1.4.1.1141.2.52.1.1
Holds the IP addresses and associated masks for ARP filtering. There are 8 addresses per ComPort.
OBJECT-TYPE    
  HcxStuSrcIpAddrEntry  

hcxStuSrcIpAddrMacAddr 1.3.6.1.4.1.1141.2.52.1.1.1
Contains IEEE 802 medium access control address of the ComPort device.
OBJECT-TYPE    
  MacAddress  

hcxStuSrcIpAddrIPAddr 1.3.6.1.4.1.1141.2.52.1.1.2
allowable IP Address for ComPort. Default 0.0.0.0.
OBJECT-TYPE    
  IpAddress  

hcxStuSrcIpAddrIPMask 1.3.6.1.4.1.1141.2.52.1.1.3
IP mask for ComPort. Default is ff.ff.ff.ff.
OBJECT-TYPE    
  IpAddress  

hcxStuSrcIpAddrUserMacAddr 1.3.6.1.4.1.1141.2.52.1.1.4
allowable MAC Address for ComPort. Default is 0:0:0:0:0:0
OBJECT-TYPE    
  MacAddress  

hcxStuSrcIpAddrIPStatus 1.3.6.1.4.1.1141.2.52.1.1.5
Used to delete or create an entry.
OBJECT-TYPE    
  Com21RowStatus  

hcxStuSrcIpAddrEtherIPAddr 1.3.6.1.4.1.1141.2.52.1.1.6
IP address of Ethernet Interface on users PC. Applicable only to telephone return.
OBJECT-TYPE    
  IpAddress  

hcxStuSrcIpAddrEntryId 1.3.6.1.4.1.1141.2.52.1.1.7
Contains table entry id.
OBJECT-TYPE    
  INTEGER 1..8  

hcxStuSrcIpAddrType 1.3.6.1.4.1.1141.2.52.1.1.8
This attribute indicates if the specified IP address/mask combination is Statically configured by NMAPS or dynamically learnt via DHCP
OBJECT-TYPE    
  INTEGER static(1), dynamic(2)  

hcxStuSrcIpAddrLeaseTimer 1.3.6.1.4.1.1141.2.52.1.1.9
This attribute indicates the lease timer value associated with a dynamically learnt IP address
OBJECT-TYPE    
  Integer32  

com21HcxStuIpFiltGroup 1.3.6.1.4.1.1141.2.53
OBJECT IDENTIFIER    

com21HcxStuIpFiltTable 1.3.6.1.4.1.1141.2.53.1
.
OBJECT-TYPE    
  SEQUENCE OF  
    HcxStuIpFiltEntry

com21HcxStuIpFiltEntry 1.3.6.1.4.1.1141.2.53.1.1
.
OBJECT-TYPE    
  HcxStuIpFiltEntry  

hcxStuIpFiltMacAddr 1.3.6.1.4.1.1141.2.53.1.1.1
Contains IEEE 802 medium access control address of the ComPort device.
OBJECT-TYPE    
  MacAddress  

hcxStuIpArpFiltEnable 1.3.6.1.4.1.1141.2.53.1.1.2
Specifies whether ARP authentication filtering should be enabled for this ComPort. This filter is applicable to 10BT, 100BT, and OC3 cards. It filters traffic in the upstream direction. Default is false. This filter can also be enabled for an entire VLAN via the MIB attribute hcxVlanIpArpFiltEnbl.
OBJECT-TYPE    
  INTEGER true(1), false(2)  

hcxStuIpArpFiltInvalidAddr 1.3.6.1.4.1.1141.2.53.1.1.3
Contains the last invalid IP Address used by the ComPort. This value is cleared on the quarter hour.
OBJECT-TYPE    
  IpAddress  

hcxStuIpArpFiltBadServAddr 1.3.6.1.4.1.1141.2.53.1.1.4
Contains the last ComController Server IP Address used by the ComPort. This value is cleared on the quarter hour.
OBJECT-TYPE    
  IpAddress  

hcxStuIpSrcFiltEnable 1.3.6.1.4.1.1141.2.53.1.1.5
Specifies whether IP source address filtering should be enabled for this ComPort. This filter is applicable to 100BT, and OC3 cards. It is not applicable to 10BT card. It filters traffic in the upstream direction. Default is false. This filter can also be enabled for an entire VLAN via the MIB attribute hcxVlanIpSrcFiltEnbl.
OBJECT-TYPE    
  INTEGER true(1), false(2)  

hcxStuIpDstFiltEnable 1.3.6.1.4.1.1141.2.53.1.1.6
Specifies whether IP destination address filtering should be enabled for this ComPort. This filter is applicable to 100BT, and OC3 cards. It is not applicable to to 10BT card. It filters traffic in the upstream direction. Default is false. This filter can also be enabled for an entire VLAN via the MIB attribute hcxVlanIpDstFiltEnbl.
OBJECT-TYPE    
  INTEGER true(1), false(2)  

hcxStuIpBootpReqFiltEnbl 1.3.6.1.4.1.1141.2.53.1.1.7
Allows enabling or disabling BOOTP Request Filter for this STU. Default: FALSE
OBJECT-TYPE    
  INTEGER true(1), false(2)  

hcxStuIpBootpReplyFiltEnbl 1.3.6.1.4.1.1141.2.53.1.1.8
Specifies whether BOOTP replies, or DHCPOFFER, or DHCPACK packets should be filtered for this ComPort. This filter is applicable to 100BT, and OC3 cards. It it not applicable to 10BT card. It filters traffic in the upstream direction. Default is false. This filter can also be enabled for an entire VLAN via the MIB attribute hcxVlanIpBootpReplyFiltEnbl.
OBJECT-TYPE    
  INTEGER true(1), false(2)  

hcxStuIpDhcpSnoopFiltEnbl 1.3.6.1.4.1.1141.2.53.1.1.9
Specifies whether DHCP snooping should be enabled for this ComPort. This filter is applicable to 100BT, and OC3 cards. It is not applicable to 10BT card. It snoops traffic in the downstream direction for DHCPACK packets, and in the upstream direction for DHCPDECLINE or DHCPRELEASE packets. Dynamic IP address assigments thus learned are stored in the valid source IP address table (com21HcxStuSrcIpAddrGroup.) Default is false. This filter can also be enabled for an entire VLAN via the MIB attribute hcxVlanIpDhcpSnoopFiltEnbl.
OBJECT-TYPE    
  INTEGER true(1), false(2)  

hcxStuL2SnapFiltEnbl 1.3.6.1.4.1.1141.2.53.1.1.10
Specifies whether SNAP-encoded IEEE 802.3 packets should be filtered for this ComPort. This filter is applicable to 100BT, and OC3 cards. It is not applicable to 10BT card. It filters traffic in both upstream and downstream directions. Default is false. This filter can also be enabled for an entire VLAN via the MIB attribute hcxVlanL2SnapFiltEnbl.
OBJECT-TYPE    
  INTEGER true(1), false(2)  

hcxStuL2NonSnapFiltEnbl 1.3.6.1.4.1.1141.2.53.1.1.11
Specifies whether non-SNAP-encoded IEEE 802.3 packets should be filtered for this ComPort. This filter is applicable to 10BT, 100BT, and OC3 cards. It filters traffic in both upstream and downstream directions. Default is false. This filter can also be enabled for an entire VLAN via the MIB attribute hcxVlanL2NonSnapFiltEnbl.
OBJECT-TYPE    
  INTEGER true(1), false(2)  

hcxStuL2EnetFiltEnbl 1.3.6.1.4.1.1141.2.53.1.1.12
Specifies whether Ethernet packets should be filtered for this ComPort. This filter is applicable to 100BT and OC3 cards. It is not applicable to 10BT card. It filters traffic in both upstream and downstream directions. Default is false. This filter can also be enabled for an entire VLAN via the MIB attribute hcxVlanL2EnetFiltEnbl.
OBJECT-TYPE    
  INTEGER true(1), false(2)  

hcxStuL2ArpIpv4FiltEnbl 1.3.6.1.4.1.1141.2.53.1.1.13
Specifies whether ARP packets should be filtered for this ComPort. This filter is applicable to 100BT and OC3 cards. It is not applicable to 10BT card. It filters traffic in both upstream and downstream directions. Default is false. This filter can also be enabled for an entire VLAN via the MIB attribute hcxVlanL2ArpIpv4FiltEnbl.
OBJECT-TYPE    
  INTEGER true(1), false(2)  

hcxStuL2Ipv4FiltEnbl 1.3.6.1.4.1.1141.2.53.1.1.14
Specifies whether IPv4 packets should be filtered for this ComPort. This filter is applicable to 100BT and OC3 cards. It is not applicable to 10BT card. It filters traffic in both upstream and downstream directions. Default is false. This filter can also be enabled for an entire VLAN via the MIB attribute hcxVlanL2Ipv4FiltEnbl.
OBJECT-TYPE    
  INTEGER true(1), false(2)  

hcxStuL2Ipv6FiltEnbl 1.3.6.1.4.1.1141.2.53.1.1.15
Specifies whether IPv6 packets should be filtered for this ComPort. This filter is applicable to 100BT and OC3 cards. It is not applicable to 10BT card. It filters traffic in both upstream and downstream directions. Default is false. This filter can also be enabled for an entire VLAN via the MIB attribute hcxVlanL2Ipv6FiltEnbl.
OBJECT-TYPE    
  INTEGER true(1), false(2)  

hcxStuL2IpxFiltEnbl 1.3.6.1.4.1.1141.2.53.1.1.16
Specifies whether IPX packets should be filtered for this ComPort. This filter is applicable to 100BT and OC3 cards. It is not applicable to 10BT card. It filters traffic in both upstream and downstream directions. Default is false. This filter can also be enabled for an entire VLAN via the MIB attribute hcxVlanL2IpxFiltEnbl.
OBJECT-TYPE    
  INTEGER true(1), false(2)  

hcxStuL2AppletalkFiltEnbl 1.3.6.1.4.1.1141.2.53.1.1.17
Specifies whether AppleTalk packets should be filtered for this ComPort. This filter is applicable to 100BT and OC3 cards. It is not applicable to 10BT card. It filters traffic in both upstream and downstream directions. Default is false. This filter can also be enabled for an entire VLAN via the MIB attribute hcxVlanL2AppleTalkFiltEnbl.
OBJECT-TYPE    
  INTEGER true(1), false(2)  

hcxStuL2OthersFiltEnbl 1.3.6.1.4.1.1141.2.53.1.1.18
Specifies whether all layer 2 packets that are none of the above (ARP, IPv4, IPv6, IPX, AppleTalk) should be filtered for this ComPort. This filter is applicable to 100BT and OC3 cards. It is not applicable to 10BT card. This filter filters traffic in both directions. This filter can also be enabled for an entire VLAN via the MIB attribute hcxVlanL2OthersFiltEnbl. Default is false.
OBJECT-TYPE    
  INTEGER true(1), false(2)  

hcxStuIpNetbiosFiltEnbl 1.3.6.1.4.1.1141.2.53.1.1.19
Specifies whether NetBIOS-over-IP packets should be filtered for this ComPort. This filter is applicable to 100BT and OC3 cards. It is not applicable to 10BT card. This filter filters traffic in the upstream direction. Default is false. This filter can also be enabled for an entire VLAN via the MIB attribute hcxVlanIpNetbiosFiltEnbl.
OBJECT-TYPE    
  INTEGER true(1), false(2)  

com21HcxStuIpFiltStatsGroup 1.3.6.1.4.1.1141.2.55
OBJECT IDENTIFIER    

com21HcxStuIpFiltStatsTable 1.3.6.1.4.1.1141.2.55.1
.
OBJECT-TYPE    
  SEQUENCE OF  
    HcxStuIpFiltStatsEntry

com21HcxStuIpFiltStatsEntry 1.3.6.1.4.1.1141.2.55.1.1
.
OBJECT-TYPE    
  HcxStuIpFiltStatsEntry  

hcxStuIpFiltStatsMacAddr 1.3.6.1.4.1.1141.2.55.1.1.1
Contains IEEE 802 medium access control address of the ComPort device.
OBJECT-TYPE    
  MacAddress  

hcxStuIpCurrArpFiltStat 1.3.6.1.4.1.1141.2.55.1.1.2
Contains the number of ARP packets from this ComPort dropped due to authentication filtering in the current 15 minute collection period.
OBJECT-TYPE    
  Gauge32  

hcxStuIpCurrSrcFiltStat 1.3.6.1.4.1.1141.2.55.1.1.3
Contains the number of IP packets from this ComPort dropped due to source address filtering in the current 15 minute collection period.
OBJECT-TYPE    
  Gauge32  

hcxStuIpCurrDstFiltStat 1.3.6.1.4.1.1141.2.55.1.1.4
Contains the number of IP packets from this ComPort dropped due to destination address filtering in the current 15 minute collection period.
OBJECT-TYPE    
  Gauge32  

hcxStuIpCurrBootpReqFiltStat 1.3.6.1.4.1.1141.2.55.1.1.5
Contains the number of bootp Req packets from this ComPort dropped due to filtering in the current 15 minute collection period.
OBJECT-TYPE    
  Gauge32  

hcxStuIpCurrBootpReplyFiltStat 1.3.6.1.4.1.1141.2.55.1.1.6
Contains the number of bootp Reply packets from this ComPort dropped due to filtering in the current 15 minute collection period.
OBJECT-TYPE    
  Gauge32  

hcxStuIpCurrDhcpSnoopFiltStat 1.3.6.1.4.1.1141.2.55.1.1.7
Contains the number of DHCP Ack packets from this ComPort snooped due to filtering in the current 15 minute collection period.
OBJECT-TYPE    
  Gauge32  

hcxStuIpPrevArpFiltStat 1.3.6.1.4.1.1141.2.55.1.1.8
Contains the number of ARP packets from this ComPort dropped due to authentication filtering in the previous 15 minute collection period.
OBJECT-TYPE    
  Gauge32  

hcxStuIpPrevSrcFiltStat 1.3.6.1.4.1.1141.2.55.1.1.9
Contains the number of IP packets from this ComPort dropped due to source address filtering in the previous 15 minute collection period.
OBJECT-TYPE    
  Gauge32  

hcxStuIpPrevDstFiltStat 1.3.6.1.4.1.1141.2.55.1.1.10
Contains the number of IP packets from this ComPort dropped due to destination address filtering in the previous 15 minute collection period.
OBJECT-TYPE    
  Gauge32  

hcxStuIpPrevBootpReqFiltStat 1.3.6.1.4.1.1141.2.55.1.1.11
Contains the number of bootp Req packets from this ComPort dropped due to filtering in the previous 15 minute collection period.
OBJECT-TYPE    
  Gauge32  

hcxStuIpPrevBootpReplyFiltStat 1.3.6.1.4.1.1141.2.55.1.1.12
Contains the number of bootp Reply packets from this ComPort dropped due to filtering in the previous 15 minute collection period.
OBJECT-TYPE    
  Gauge32  

hcxStuIpPrevDhcpSnoopFiltStat 1.3.6.1.4.1.1141.2.55.1.1.13
Contains the number of DHCP Ack packets from this ComPort snooped due to filtering in the previous 15 minute collection period.
OBJECT-TYPE    
  Gauge32  

hcxStuIpClearStats 1.3.6.1.4.1.1141.2.55.1.1.14
This attribute is used to clear all IP Filter statistics counters in this group. This operation is only possible if the hcxStatsControl attribute is set to wrapCurr.
OBJECT-TYPE    
  INTEGER nil(1), clear(2)  

hcxStuL2CurrSnapFiltStat 1.3.6.1.4.1.1141.2.55.1.1.15
Contains the number of SNAP-encoded IEEE 802.3 packets filtered in the current 15 min collection period.
OBJECT-TYPE    
  Gauge32  

hcxStuL2CurrNonSnapFiltStat 1.3.6.1.4.1.1141.2.55.1.1.16
Contains the number of non-SNAP-encoded IEEE 802.3 packets filtered in the current 15 min collection period.
OBJECT-TYPE    
  Gauge32  

hcxStuL2CurrEnetFiltStat 1.3.6.1.4.1.1141.2.55.1.1.17
Contains the number of Ethernet packets filtered in the current 15 min collection period.
OBJECT-TYPE    
  Gauge32  

hcxStuL2CurrArpIpv4FiltStat 1.3.6.1.4.1.1141.2.55.1.1.18
Contains the number of ARP for IPv4 packets filtered in the current 15 min collection period.
OBJECT-TYPE    
  Gauge32  

hcxStuL2CurrIpv4FiltStat 1.3.6.1.4.1.1141.2.55.1.1.19
Contains the number of IPv4 packets filtered in the current 15 min collection period.
OBJECT-TYPE    
  Gauge32  

hcxStuL2CurrIpv6FiltStat 1.3.6.1.4.1.1141.2.55.1.1.20
Contains the number of IPv6 packets filtered in the current 15 min collection period.
OBJECT-TYPE    
  Gauge32  

hcxStuL2CurrIpxFiltStat 1.3.6.1.4.1.1141.2.55.1.1.21
Contains the number of IPX packets filtered in the current 15 min collection period.
OBJECT-TYPE    
  Gauge32  

hcxStuL2CurrAppletalkFiltStat 1.3.6.1.4.1.1141.2.55.1.1.22
Contains the number of Appletalk packets filtered in the current 15 min collection period.
OBJECT-TYPE    
  Gauge32  

hcxStuL2CurrOthersFiltStat 1.3.6.1.4.1.1141.2.55.1.1.23
Contains the number of packets that are non of the above that are filtered in the current 15 min collection period.
OBJECT-TYPE    
  Gauge32  

hcxStuIpCurrNetbiosFiltStat 1.3.6.1.4.1.1141.2.55.1.1.24
Contains the number of Netbios packets filtered in the current 15 min collection period.
OBJECT-TYPE    
  Gauge32  

hcxStuL2PrevSnapFiltStat 1.3.6.1.4.1.1141.2.55.1.1.25
Contains the number of SNAP-encoded IEEE 802.3 packets filtered in the previous 15 min collection period.
OBJECT-TYPE    
  Gauge32  

hcxStuL2PrevNonSnapFiltStat 1.3.6.1.4.1.1141.2.55.1.1.26
Contains the number of non-SNAP-encoded IEEE 802.3 packets filtered in the previous 15 min collection period.
OBJECT-TYPE    
  Gauge32  

hcxStuL2PrevEnetFiltStat 1.3.6.1.4.1.1141.2.55.1.1.27
Contains the number of Ethernet packets filtered in the previous 15 min collection period.
OBJECT-TYPE    
  Gauge32  

hcxStuL2PrevArpIpv4FiltStat 1.3.6.1.4.1.1141.2.55.1.1.28
Contains the number of ARP for IPv4 packets filtered in the previous 15 min collection period.
OBJECT-TYPE    
  Gauge32  

hcxStuL2PrevIpv4FiltStat 1.3.6.1.4.1.1141.2.55.1.1.29
Contains the number of IPv4 packets filtered in the previous 15 min collection period.
OBJECT-TYPE    
  Gauge32  

hcxStuL2PrevIpv6FiltStat 1.3.6.1.4.1.1141.2.55.1.1.30
Contains the number of IPv6 packets filtered in the previous 15 min collection period.
OBJECT-TYPE    
  Gauge32  

hcxStuL2PrevIpxFiltStat 1.3.6.1.4.1.1141.2.55.1.1.31
Contains the number of IPX packets filtered in the previous 15 min collection period.
OBJECT-TYPE    
  Gauge32  

hcxStuL2PrevAppletalkFiltStat 1.3.6.1.4.1.1141.2.55.1.1.32
Contains the number of Appletalk packets filtered in the previous 15 min collection period.
OBJECT-TYPE    
  Gauge32  

hcxStuL2PrevOthersFiltStat 1.3.6.1.4.1.1141.2.55.1.1.33
Contains the number of packets that are non of the above that are filtered in the previous 15 min collection period.
OBJECT-TYPE    
  Gauge32  

hcxStuIpPrevNetbiosFiltStat 1.3.6.1.4.1.1141.2.55.1.1.34
Contains the number of Netbios packets filtered in the previous 15 min collection period.
OBJECT-TYPE    
  Gauge32  

com21HcxStuDstIpAddrGroup 1.3.6.1.4.1.1141.2.57
OBJECT IDENTIFIER    

com21HcxStuDstIpAddrTable 1.3.6.1.4.1.1141.2.57.1
.
OBJECT-TYPE    
  SEQUENCE OF  
    HcxStuDstIpAddrEntry

com21HcxStuDstIpAddrEntry 1.3.6.1.4.1.1141.2.57.1.1
Holds the IP addresses and associated masks for ARP filtering. There are 8 addresses per ComPort.
OBJECT-TYPE    
  HcxStuDstIpAddrEntry  

hcxStuDstIpAddrMacAddr 1.3.6.1.4.1.1141.2.57.1.1.1
Contains IEEE 802 medium access control address of the ComPort device.
OBJECT-TYPE    
  MacAddress  

hcxStuDstIpAddrIPAddr 1.3.6.1.4.1.1141.2.57.1.1.2
allowable IP Address for ComPort. Default 0.0.0.0.
OBJECT-TYPE    
  IpAddress  

hcxStuDstIpAddrIPMask 1.3.6.1.4.1.1141.2.57.1.1.3
IP mask for ComPort. Default is ff.ff.ff.ff.
OBJECT-TYPE    
  IpAddress  

hcxStuDstIpAddrIPStatus 1.3.6.1.4.1.1141.2.57.1.1.4
Used to delete or create an entry.
OBJECT-TYPE    
  Com21RowStatus  

hcxStuDstIpAddrEntryId 1.3.6.1.4.1.1141.2.57.1.1.5
Contains table entry id.
OBJECT-TYPE    
  INTEGER 1..8  

hcxStuAcqEvent 1.3.6.1.4.1.1141.4.90
This trap is issued only when the acquisition trap is enabled via the hcxStuAcqTrapEnable attribute. Severity WARNING.
NOTIFICATION-TYPE    
  hcxAlmSeverity  
  hcxEventLogTime  
  hcxStuStatusMacAddr  

hcxStuDeacqEvent 1.3.6.1.4.1.1141.4.91
This trap is issued only when the acquisition trap is enabled via the hcxStuAcqTrapEnable attribute. Severity WARNING.
NOTIFICATION-TYPE    
  hcxAlmSeverity  
  hcxEventLogTime  
  hcxStuStatusMacAddr  

hcxIncompSwVersion 1.3.6.1.4.1.1141.4.100
This trap is issued if the configured sw version (in hcxStuConfSwImage) is not applicable to the hw version/hw options reported by the ComPort. This an event with no clear condition. Only severity is WARNING.
NOTIFICATION-TYPE    
  hcxAlmSeverity  
  hcxEventLogTime  
  hcxStuStatusMacAddr  

hcxUnavailSwVersion 1.3.6.1.4.1.1141.4.101
This trap is issued if the configured image cannot be located on the ComController. This an event with no clear condition. Only severity is WARNING.
NOTIFICATION-TYPE    
  hcxAlmSeverity  
  hcxEventLogTime  
  hcxStuStatusMacAddr  

hcxStuPingTestComplete 1.3.6.1.4.1.1141.4.102
This trap is issued when the ping test is completed. This an event with no clear condition. Only severity is WARNING.
NOTIFICATION-TYPE    
  hcxAlmSeverity  
  hcxEventLogTime  
  hcxStuStatusMacAddr  
  hcxStuPingTestResult  

hcxStuEthTestComplete 1.3.6.1.4.1.1141.4.103
This notification is generated whenever the ComPort loopback test is completed. This shall either be completed after reception of looped back packet(s) or after a timeout. This an event with no clear condition. Only severity is WARNING.
NOTIFICATION-TYPE    
  hcxAlmSeverity  
  hcxEventLogTime  
  hcxStuStatusMacAddr  
  hcxStuEthTestResult  

hcxStuAcqRangeFail 1.3.6.1.4.1.1141.4.104
This trap is issued if an RX card reports a failure to range a previously acquired ComPort. Note that the ComPort states are defined in the proxy ComPort MIB. This an event with no clear condition. Only severity is WARNING.
NOTIFICATION-TYPE    
  hcxAlmSeverity  
  hcxEventLogTime  
  hcxStuStatusMacAddr  

hcxStuAcqOnlineFail 1.3.6.1.4.1.1141.4.105
This trap is issued if an RX card successfully acquires an ComPort, but the ComPort cannot be placed online due to a ComController or ComPort failure. Only severity is WARNING.
NOTIFICATION-TYPE    
  hcxAlmSeverity  
  hcxEventLogTime  
  hcxStuStatusMacAddr  

hcxStuArpInvalidAddr 1.3.6.1.4.1.1141.4.106
this trap is generated whenever an invalid ARP IP source address is detected. Severity is WARNING.
NOTIFICATION-TYPE    
  hcxAlmSeverity  
  hcxEventLogTime  
  hcxStuIpFiltMacAddr  
  hcxStuIpArpFiltInvalidAddr  

hcxStuArpBadServerAddr 1.3.6.1.4.1.1141.4.107
this trap is generated whenever the ComPort is detected as utilizing a reserved server address as its source IP address. Severity is WARNING.
NOTIFICATION-TYPE    
  hcxAlmSeverity  
  hcxEventLogTime  
  hcxStuIpFiltMacAddr  
  hcxStuIpArpFiltBadServAddr  

hcxStuRangFailPowerLow 1.3.6.1.4.1.1141.4.108
This trap is generated when the RX card cannot set a ComPort's power level correctly - the ComPort has too low a power level. This alarm is generated once and cleared only when the condition is corrected or the ComPort is deacquired. Default severity is MINOR.
NOTIFICATION-TYPE    
  hcxAlmSeverity  
  hcxEventLogTime  
  hcxStuStatusMacAddr  

hcxStuRangFailPowerHigh 1.3.6.1.4.1.1141.4.109
This trap is generated when the RX card cannot set a ComPort's power level correctly - the ComPort has too high a power level. This alarm is generated once and cleared only when the condition is corrected or the ComPort is deacquired. Default severity is MINOR.
NOTIFICATION-TYPE    
  hcxAlmSeverity  
  hcxEventLogTime  
  hcxStuStatusMacAddr  

hcxStuRangFailLowClear 1.3.6.1.4.1.1141.4.140
This trap is generated when the RX card successful ranges a ComPort that was previously reported as in the low power state or when a ComPort in that state is deacquired. Severity is CLEARED.
NOTIFICATION-TYPE    
  hcxAlmSeverity  
  hcxEventLogTime  
  hcxStuStatusMacAddr  

hcxStuRangFailHighClear 1.3.6.1.4.1.1141.4.141
This trap is generated when the RX card successful ranges a ComPort that was previously reported as in the high power state or when a ComPort in that state is deacquired. Severity is CLEARED.
NOTIFICATION-TYPE    
  hcxAlmSeverity  
  hcxEventLogTime  
  hcxStuStatusMacAddr  

Defined Objects

FrequencyKhz  
INTEGER 0..800000    

Com21RowStatus  
INTEGER active(1), create(2), destroy(3), deactive(4)    

StuGain  
INTEGER 18..58    

HcxStuStatusEntry  
SEQUENCE    
  MacAddress as hcxStuStatusMacAddr  
  INTEGER as hcxStuConfigured  
  INTEGER as hcxStuAcquired  
  INTEGER as hcxStuAcqFailInfo  
  INTEGER as hcxStuAuthorized  
  INTEGER as hcxStuLedFlashTest  
  INTEGER as hcxStuUpstreamTest  
  INTEGER as hcxStuVlanId  
  INTEGER as hcxStuRxShelfId  
  INTEGER as hcxStuRxSlotId  
  INTEGER as hcxStuRxPortId  
  Integer32 as hcxStuServiceType  
  DisplayString as hcxStuConfSwImage  
  INTEGER as hcxStuPingTestAction  
  INTEGER as hcxStuPingTestResult  
  INTEGER as hcxStuEthTestAction  
  INTEGER as hcxStuEthTestResult  
  INTEGER as hcxStuRetPathSelect  
  INTEGER as hcxStuEth8022Filter  
  INTEGER as hcxStuDnstrmFwdCntrl  
  INTEGER as hcxStuStatsCollect  
  INTEGER as hcxStuPowerRangeState  
  INTEGER as hcxStuRpmIPortId  
  Integer32 as hcxStuEthLpbkTestUpRate  
  Integer32 as hcxStuEthLpbkTestLatency  
  INTEGER as hcxStuModelName  
  Integer32 as hcxStuEthTestDnRate  
  INTEGER as hcxStuEthLpbkTestDuration  

HcxStuSrcIpAddrEntry  
SEQUENCE    
  MacAddress as hcxStuSrcIpAddrMacAddr  
  IpAddress as hcxStuSrcIpAddrIPAddr  
  IpAddress as hcxStuSrcIpAddrIPMask  
  MacAddress as hcxStuSrcIpAddrUserMacAddr  
  Com21RowStatus as hcxStuSrcIpAddrIPStatus  
  IpAddress as hcxStuSrcIpAddrEtherIPAddr  
  INTEGER as hcxStuSrcIpAddrEntryId  
  INTEGER as hcxStuSrcIpAddrType  
  Integer32 as hcxStuSrcIpAddrLeaseTimer  

HcxStuDstIpAddrEntry  
SEQUENCE    
  MacAddress as hcxStuDstIpAddrMacAddr  
  IpAddress as hcxStuDstIpAddrIPAddr  
  IpAddress as hcxStuDstIpAddrIPMask  
  Com21RowStatus as hcxStuDstIpAddrIPStatus  
  INTEGER as hcxStuDstIpAddrEntryId  

HcxStuIpFiltEntry  
SEQUENCE    
  MacAddress as hcxStuIpFiltMacAddr  
  INTEGER as hcxStuIpArpFiltEnable  
  IpAddress as hcxStuIpArpFiltInvalidAddr  
  IpAddress as hcxStuIpArpFiltBadServAddr  
  INTEGER as hcxStuIpSrcFiltEnable  
  INTEGER as hcxStuIpDstFiltEnable  
  INTEGER as hcxStuIpBootpReqFiltEnbl  
  INTEGER as hcxStuIpBootpReplyFiltEnbl  
  INTEGER as hcxStuIpDhcpSnoopFiltEnbl  
  INTEGER as hcxStuL2SnapFiltEnbl  
  INTEGER as hcxStuL2NonSnapFiltEnbl  
  INTEGER as hcxStuL2EnetFiltEnbl  
  INTEGER as hcxStuL2ArpIpv4FiltEnbl  
  INTEGER as hcxStuL2Ipv4FiltEnbl  
  INTEGER as hcxStuL2Ipv6FiltEnbl  
  INTEGER as hcxStuL2IpxFiltEnbl  
  INTEGER as hcxStuL2AppletalkFiltEnbl  
  INTEGER as hcxStuL2OthersFiltEnbl  
  INTEGER as hcxStuIpNetbiosFiltEnbl  

HcxStuIpFiltStatsEntry  
SEQUENCE    
  MacAddress as hcxStuIpFiltStatsMacAddr  
  Gauge32 as hcxStuIpCurrArpFiltStat  
  Gauge32 as hcxStuIpCurrSrcFiltStat  
  Gauge32 as hcxStuIpCurrDstFiltStat  
  Gauge32 as hcxStuIpCurrBootpReqFiltStat  
  Gauge32 as hcxStuIpCurrBootpReplyFiltStat  
  Gauge32 as hcxStuIpCurrDhcpSnoopFiltStat  
  Gauge32 as hcxStuL2CurrSnapFiltStat  
  Gauge32 as hcxStuL2CurrNonSnapFiltStat  
  Gauge32 as hcxStuL2CurrEnetFiltStat  
  Gauge32 as hcxStuL2CurrArpIpv4FiltStat  
  Gauge32 as hcxStuL2CurrIpv4FiltStat  
  Gauge32 as hcxStuL2CurrIpv6FiltStat  
  Gauge32 as hcxStuL2CurrIpxFiltStat  
  Gauge32 as hcxStuL2CurrAppletalkFiltStat  
  Gauge32 as hcxStuL2CurrOthersFiltStat  
  Gauge32 as hcxStuIpCurrNetbiosFiltStat  
  Gauge32 as hcxStuIpPrevArpFiltStat  
  Gauge32 as hcxStuIpPrevSrcFiltStat  
  Gauge32 as hcxStuIpPrevDstFiltStat  
  Gauge32 as hcxStuIpPrevBootpReqFiltStat  
  Gauge32 as hcxStuIpPrevBootpReplyFiltStat  
  Gauge32 as hcxStuIpPrevDhcpSnoopFiltStat  
  Gauge32 as hcxStuL2PrevSnapFiltStat  
  Gauge32 as hcxStuL2PrevNonSnapFiltStat  
  Gauge32 as hcxStuL2PrevEnetFiltStat  
  Gauge32 as hcxStuL2PrevArpIpv4FiltStat  
  Gauge32 as hcxStuL2PrevIpv4FiltStat  
  Gauge32 as hcxStuL2PrevIpv6FiltStat  
  Gauge32 as hcxStuL2PrevIpxFiltStat  
  Gauge32 as hcxStuL2PrevAppletalkFiltStat  
  Gauge32 as hcxStuL2PrevOthersFiltStat  
  Gauge32 as hcxStuIpPrevNetbiosFiltStat  
  Gauge as hcxStuIpClearStats