
COM21-HCXTOP-MIB
File:
COM21-HCXTOP-MIB.mib (81304 bytes)
Imported modules
Imported symbols
Defined Objects
| com21HcxCtrl |
1.3.6.1.4.1.1141.2.1 |
| This is the Com21 ComController Unit Control MIB module. It provides for overall, high-level control of the ComController and comUNITY system. COM21 Part# 005-0025-00 |
| MODULE-IDENTITY |
|
|
|
| hcxEncryptionEnable |
1.3.6.1.4.1.1141.2.2.2 |
| Used to enable or disable encryption on a system basis. Default is true. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
true(1), false(2) |
|
| hcxUserText |
1.3.6.1.4.1.1141.2.2.5 |
| The User Text is a non-volatile string which is set by the management system with an arbitrary value. This value does not have to be unique. It's purpose is solely to assist the carrier personnel with identifying the ComController device. |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
SIZE(32) |
|
| hcxRestartAction |
1.3.6.1.4.1.1141.2.2.9 |
| The Restart Action is an active-value. The setting of this value to warmStart(2) causes the ComController to restart utilizing the present active software load. The setting of this value to coldStart(3) causes the ComController to restart, refreshing the current active firmware images and the active configuration file from the NMAPS. This completion of the reboot shall be indicated by the standard SNMP warmStart or coldStart trap. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
nil(1), warmStart(2), coldStart(3) |
|
| hcxMajorAlarmStatusLed |
1.3.6.1.4.1.1141.2.2.10 |
| The Major Alarm Status LED is a read-only variable which describes the condition of the ComController Major Alarm Status light emitting diode located on the CC board. A value of on(1) indicates that a Major alarm exists and that the LED is illuminated. A value of off(2) indicates that no major alarm condition is detected. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
on(1), off(2) |
|
| hcxMinorAlarmStatusLed |
1.3.6.1.4.1.1141.2.2.11 |
| The Minor Alarm Status LED is a read-only variable which describes the condition of the ComController Minor Alarm Status light emitting diode located on the CC board. A value of on(1) indicates that a Minor alarm exists and that the LED is illuminated. A value of off(2) indicates that no minor alarm condition is detected. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
on(1), off(2) |
|
| hcxAutoLoadBalancing |
1.3.6.1.4.1.1141.2.2.12 |
| This attribute controls whether the ComController shall perform automatic load balancing after an RX resource is added (or restored to the system). Default is on. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
on(1), off(2) |
|
| hcxAutoFreqHopping |
1.3.6.1.4.1.1141.2.2.13 |
| This attribute controls whether the ComController shall perform automatic frequency hopping. Note that the auto frequency hopping can also be controlled on a specific RX port basis. Turning this attribute off will override the individual ComPort configurations. Default will be on. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
on(1), off(2) |
|
| hcxKeyRenewalPeriod |
1.3.6.1.4.1.1141.2.2.14 |
| Contains the period at which encryption keys should be renewed. This attribute is expressed in hours. i.e. value of 48 indicates a 48hour renewal frequency. Default is 24. 0 disables renewal. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0..8784 |
|
| hcxHcxSwDnldResult |
1.3.6.1.4.1.1141.2.2.18 |
| This attribute contains the result of the last ComController software image download from the boot server. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
inprogress(1), success(2), serverNoResponse(3), imageNotFound(4), versionMismatch(5), serverConnectionLost(6), uninitiated(7) |
|
| hcxCnfgBackupAction |
1.3.6.1.4.1.1141.2.2.21 |
| This attribute is provided to allow a user to trigger a backup of ComController configuration data on to the boot server. backupToSaved is used to create a user controlled backup on NMAPS. revertToSaved is used retrieve a saved database from NMAPS. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
nil(1), backupToSaved(2), revertToSaved(3) |
|
| hcxCnfgBackupResult |
1.3.6.1.4.1.1141.2.2.22 |
| This attribute contains the result of the last configuration data backup operation. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
inprogress(1), success(2), serverNoResponse(3), writeFailed(4), uninitiated(5) |
|
| hcxPhyConfigType |
1.3.6.1.4.1.1141.2.2.23 |
| This attribute details the physical configuration type of the ComController. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
singleShelf(1), fullConfig(2), compactShelf(3) |
|
| hcxNumOfShelves |
1.3.6.1.4.1.1141.2.2.24 |
| This attribute specifies the number of shelves in the system. Presently one or two. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..2 |
|
| hcxBootpResult |
1.3.6.1.4.1.1141.2.2.26 |
| This attribute contains the result of the last bootp operation. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
inprogress(1), success(2), serverNoResponse(3), serverUnknown(4), imageNotFound(5), versionMismatch(6), serverConnectionLost(7) |
|
| hcxFreqHopPause |
1.3.6.1.4.1.1141.2.2.28 |
| This attribute defines the number of seconds between a failed frequency hopping operation and a subsequent attempt. If a given upstream frequency is found to be in an error state, then the HCX will cycle through the configured alternates. If all these alternates are also found to be in a degraded state, then the HCX shall pause for the number of seconds defined by this attribute before attempting another hop. Default 30secs. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0..300 |
|
| hcxMaxDnstrmCBRAlloc |
1.3.6.1.4.1.1141.2.2.29 |
| This attribute defines the maximum percentage of downstream bandwidth that can be allocated to CBR traffic. This control mechanism will denied service to acquiring ComPorts if the addition of the configured CBR bandwidth would exceed the defined percentage. Note that this is a limit. i.e. if this attribute is set to 50%, then UP TO half the bandwidth can be CBR. It does not mean that half WILL be CBR. 100%, the default, means in effect there is no control. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0..100 |
|
| hcxMaxUpstrmCBRAlloc |
1.3.6.1.4.1.1141.2.2.30 |
| This attribute defines the maximum percentage of upstream bandwidth that can be allocated to CBR traffic. Default 100. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0..100 |
|
| hcxHcxAlternateSwRel |
1.3.6.1.4.1.1141.2.2.31 |
| This attribute details the alternate software revision. It is written after cold boot by the CC and later can be written by the user. If this value is written by the user - note that the release need not necessarily change - then the CC shall retrieve a new set of alternate images from the boot server. Format is a.b.c.ddd. |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
SIZE(32) |
|
| hcxHcxImageControl |
1.3.6.1.4.1.1141.2.2.32 |
| This attribute is used to activate a given revision of software images. The CC shall automatically reboot if this field is changed by the user and the version input is valid. Format is a.b.c.ddd. |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
SIZE(32) |
|
| hcxStatsControl |
1.3.6.1.4.1.1141.2.2.33 |
| This attribute controls the statistics collection mechanism. If previousCounts is selected then the current stats shall be copied into the previous stats counts every 15minutes. If wrapCurr is selected, then there shall be no copying in to previous counts and the current counters shall wrap. If NMAPS is utilized then previousCounts MUST be selected. Default previousCounts. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
previousCounts(1), wrapCurr(2) |
|
| hcxImageTransfer |
1.3.6.1.4.1.1141.2.2.34 |
| This attribute is used tell the CC to download an individual ComController software image from the boot server (NMAPS) to PCMCIA disk. Images transfered as a result of this command are not loaded to the corresponding card - to do this, the uploaded image must be made to be the primary image and the card must be rebooted. The images are specified via , where the revision is of the a.b.c.ddd format and the image type is one of the following: rx - RX card rxm - RXM card tx - TX card cc - CC card 10bt - 10bT card 100bt - 100bT card oc3 - OC3 card atm - ATM switch comp - compact HCX image stu3com - 3COM modem image(s) stu - COM21 ComPort images The CC will check the validity of the revision number against the hcxHcxSwRelease and hcxHcxAlternateSwRel values. |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
SIZE(32) |
|
| hcxSyncClkSelect |
1.3.6.1.4.1.1141.2.2.37 |
| specifies the clock selected for synchronization. Default is internalClk. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
internalClk(1), priNetworkClk(2), secNetworkClk(3) |
|
| hcxAcqMinPower |
1.3.6.1.4.1.1141.2.3.6 |
| Contains the minimum power setting to be used by the ComPort when hunting for upstream channel. This data is used in the INVITE_CONFIG message. Default 18. |
| OBJECT-TYPE |
|
|
|
| |
StuGain |
|
|
| hcxAcqMaxPower |
1.3.6.1.4.1.1141.2.3.7 |
| Contains the maximum power setting to be used by the ComPort when hunting for upstream channel. This data is used in the INVITE_CONFIG message. Default 58. |
| OBJECT-TYPE |
|
|
|
| |
StuGain |
|
|
| hcxAcqPowerStepSize |
1.3.6.1.4.1.1141.2.3.8 |
| Contains the power step size to be used by the ComPort when hunting for upstream channel. This data is used in the INVITE_CONFIG message. Default 1. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..20 |
|
| hcxEventLogSize |
1.3.6.1.4.1.1141.2.4.2 |
| Contains the maximum number of events to be stored in the log. Default is 200. Upper limit will be controlled by the available memory. Set to 1000 for now. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
10..1000 |
|
| hcxNumAcquiredStus |
1.3.6.1.4.1.1141.2.5.2 |
| This value contains the number of acquired ComPorts for this ComController. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0..2048 |
|
| hcxNumEnabledStus |
1.3.6.1.4.1.1141.2.5.4 |
| This value contains the number of enabled and active ComPorts on this ComController. Note that we assume all ComPort support ethernet if. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0..2048 |
|
| hcxStuAggrUpStrmCbrRate |
1.3.6.1.4.1.1141.2.5.5 |
| This attribute defines the aggregate of all ComPort upstream CBR rates in the ComController. This includes both acquired and unacquired ComPorts. Defined in Kbps. |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| hcxStuAggrUpStrmMinRate |
1.3.6.1.4.1.1141.2.5.6 |
| This attribute defines the aggregate of all ComPort upstream minimum PCR rates in the ComController. This includes both acquired and unacquired ComPorts. Defined in Kbps. |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| hcxStuAggrUpStrmMaxRate |
1.3.6.1.4.1.1141.2.5.7 |
| This attribute defines the aggregate of all ComPort upstream maximum rates in the ComController. This includes both acquired and unacquired ComPorts. Defined in Kbps. |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| hcxStuAltDownFreq |
1.3.6.1.4.1.1141.2.5.9 |
| This attribute defines an alternate ComController downstream frequency. This attribute would be utilized if an unrecognized ComPort is acquired and the hcxStuAltDownFreqEnable is set to enable. Minimum step size is 200. i.e. 200000hz. Default is 0, indicating no alternate frequency. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
88000..800000 |
|
| hcxStuAcqTrapEnable |
1.3.6.1.4.1.1141.2.5.11 |
| Indicates whether the topology change trap mechanism should be used, or a trap per STU acq, or both. Note that NMAPS is dependant upon the topology change mechanism, so should be disabled only when NMAPS is not in use. Also be aware that a high number of traps will occur if the per acq trap is selected. Default is topoChgTrapOnly. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
topoChgTrapOnly(1), acqTrapOnly(2), bothTopoAndAcqTrap(3) |
|
| hcxStuRpcEnable |
1.3.6.1.4.1.1141.2.5.12 |
| Controls whether the system offers an RPC based interface for statistics and ComPort status. Default is true. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
true(1), false(2) |
|
| hcxStuAutoDiscEnable |
1.3.6.1.4.1.1141.2.5.13 |
| Controls whether the system performs auto discover of telephone return ComPorts. Default is true. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
true(1), false(2) |
|
| hcxStuAutoDiscIpAddr |
1.3.6.1.4.1.1141.2.5.14 |
| The IP address of the return path interface of a PC that will enable autodiscovery of a ComPORT operating in Telephone Return mode. A PC must be present with this address on an established return path connection to allow telephone return autodiscovery to take place. |
| OBJECT-TYPE |
|
|
|
| |
IpAddress |
|
|
| hcxStuAutoGainAdjust |
1.3.6.1.4.1.1141.2.5.15 |
| This attribute is used to control the automatic adjustment of ComPort gain after acquisition. Default is disable. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
disable(1), enable(2) |
|
| hcxStuAltDownFreqEnable |
1.3.6.1.4.1.1141.2.5.16 |
| This attribute is used to control the automatic setting of an alternate downstream frequency. If enabled, the hcxStuAltDownFreq shall be set in any unconfigured ComPort acquired by an HCX. Note that this feature CANNOT be enabled if hcxStuDefaultAuth is set to true or hcxStuAltDownFreq is set to 0. Default is disabled. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
disable(1), enable(2) |
|
| hcxStuPcMacAddress |
1.3.6.1.4.1.1141.2.5.17 |
| This attribute is used to set the mac address of the PC. Setting this attribute starts a search for the mac address of the ComPort that is connected to this PC. |
| OBJECT-TYPE |
|
|
|
| |
MacAddress |
|
|
| hcxStuPcToStuMacAddressResult |
1.3.6.1.4.1.1141.2.5.18 |
| This attribute contains the result of the last PC to ComPort mac address search. It changes to 'inprogress' when hcxStuPcMacAddress is set. When the search completes this attribute will display either 'success' or 'failure'. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
inprogress(1), success(2), failure(3) |
|
| hcxStuOverMacAddress |
1.3.6.1.4.1.1141.2.5.19 |
| This attribute displays the mac address of the ComPort that is connected to the PC with mac address hcxStuPcMacAddress. The value is valid only if hcxStuPcToStuMacAddressResult displays success. |
| OBJECT-TYPE |
|
|
|
| |
MacAddress |
|
|
| hcxStuGlobalSwImage |
1.3.6.1.4.1.1141.2.5.20 |
| This attribute provides an easy way to change the configured software image for all configured ComPorts without having to modify hcxStuConfSwImage of individual ComPorts. When this attribute is written to by the user, the hcxStuConfSwImage attribute for all configured ComPorts will be automatically modified to reflect this value. However, this is only a one-time action. The user is free to modify the hcxStuConfSwImage attribute of individual ComPorts to other values. Since this attribute only affects configured ComPorts, it does not interfere with hcxStuDefCom21SwImage or hcxStuDef3ComSwImage from com21HcxStuDefaultGroup. Default is 0.0.0.0. Also, it will reset back to 0.0.0.0 upon a ComController reboot. |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
SIZE(16) |
|
| hcxTrapReceiverEntry |
1.3.6.1.4.1.1141.2.6.1.1 |
| A destination address and community string to a particular trap server, along with a trap filter and entry aging capability. |
| OBJECT-TYPE |
|
|
|
| |
HcxTrapReceiverEntry |
|
|
| hcxTrapRcvrStatus |
1.3.6.1.4.1.1141.2.6.1.1.1 |
| Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the hcxTrapReceiverTable. That is, it effectively disassociates the address identified with the entry by removing the entry from the table. On a read the value of valid(1) should be returned if the entry contains a valid record, or invalid(2) should be returned if the entry contains an invalid record. Default is valid. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
valid(1), invalid(2), delete(3) |
|
| hcxTrapRcvrComm |
1.3.6.1.4.1.1141.2.6.1.1.3 |
| Community string used for traps sent to this trap receiver. Note that this string is writable only by the CC CUI. |
| OBJECT-TYPE |
|
|
|
| |
OCTET STRING |
SIZE(0..16) |
|
| hcxTrapRcvrAgeTime |
1.3.6.1.4.1.1141.2.6.1.1.4 |
| This is the time interval used to age entries out of the trap receiver table. The default value if not specified will be 0, or infinite, never to be aged out. At least initially, there will be no transient management devices in the comUNITY system. Therefore this attibute will always be set to 0. |
| OBJECT-TYPE |
|
|
|
| |
TimeTicks |
|
|
| hcxSlotSupportedTypes |
1.3.6.1.4.1.1141.2.8.1.1.3 |
| contains card types supported for this slot. com21Exp specifies 10baseT or 100baseT or oc3. intConn is the interconnect card used on the expansion shelf (Shelf2). rxIntConn is used to indicate a slot that can be used for an RX, 100bT or 10bT card in the single shelf configuration or for the interconnect card when an expansion shelf is present. rx indicates either RX or RXM cards. On the expansion shelf there is support of up to 8 rx cards. rxCom21Exp defines RX, oc3, 10bT or 100bT card for slots 3 and 4. For all other slots it defines Rx, 10bT or 100bT cards (This implies that oc3 card is supported only in slots 2,3 and 4). Note that there is a maximum of 5x10bT/100bT and 12xRX in the system. maximum number of oc3 cards supported is 2 Release 2.3 software shall support the following slot designations. if hcxPhyConfigType = singleShelf: Shelf 1 Slot 1 - cc Slot 2 - com21Exp Slot 3 - rxCom21Exp Slot 4 - rxCom21Exp Slot 5 - rxIntConn Slot 6 - rxCom21Exp Slot 7 - rxCom21Exp Slot 8 - rx Slot 9 - rx Slot 10 - txDig Slot 11 - tx if hcxPhyConfigType = fullShelf: Shelf 1 Shelf2 Slot 1 - cc Slot 1 - intConn Slot 2 - com21Exp Slot 2 - rx Slot 3 - rxCom21Exp Slot 3 - rx Slot 4 - rxCom21Exp Slot 4 - rx Slot 5 - rxIntConn Slot 5 - rx Slot 6 - rxCom21Exp Slot 6 - rx Slot 7 - rxCom21Exp Slot 7 - rx Slot 8 - rx Slot 8 - rx Slot 9 - rx Slot 9 - rx Slot 10 - txDig Slot 10 - noCard Slot 11 - tx Slot 11 - noCard if hcxPhyConfigType = compactShelf: Shelf 1 Slot 1 - cc Slot 2 - com21Exp Slot 3 - rxCom21Exp Slot 4 - rx Slot 5 - txDig Slot 6 - tx |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
rx(1), tx(2), cc(3), com21Exp(4), txDig(5), intConn(6), rxIntConn(7), noCard(8), rxCom21Exp(9) |
|
| hcxSlotConfigCardType |
1.3.6.1.4.1.1141.2.8.1.1.4 |
| contains card type configured for this slot. This attribute will be checked against the set of supported card types and rejected if not present. Note that the cardtype of ethDual10bT can be used to specify either the 4k or 8k CAM versions of the 10bT card. Note that a 10bT or 100bT or oc3 card CANNOT be unconfigured if an STU on an associated VLAN is acquired. |
| OBJECT-TYPE |
|
|
|
| |
HcxCardType |
|
|
| hcxImageType |
1.3.6.1.4.1.1141.2.9.1.1.2 |
| contains image type. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
hcxCC(1), hcxTx(2), hcxRx(3), hcxEth10baseT(4), hcxEth100baseT(5), hcxTele(6), stu(7), stu3com(8), hcxRxm(9), atmlSwitch(10), compCfg(11), compSwitch(12), hcxOc3(13) |
|
| hcxHwRevision |
1.3.6.1.4.1.1141.2.9.1.1.5 |
| contains hardware revision supported by this image. Note that in the future, we may define a range of hardware revisions supported. |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
SIZE(32) |
|
| hcxFwRevision |
1.3.6.1.4.1.1141.2.9.1.1.6 |
| contains firmware boot revision supported by this image. Note that in the future, we may define a range of hardware revisions supported. |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
SIZE(32) |
|
| hcxImageState |
1.3.6.1.4.1.1141.2.9.1.1.7 |
| this attribute specifies the state of an image. An image is either part of the active set of ComController and ComPort images, or is a part of the alternate set. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
active(1), alternate(2) |
|
| hcxDnStrmType |
1.3.6.1.4.1.1141.2.10.1.1.3 |
| defines CBR or ondemand (UBR) traffic in the downstream direction. Default is ondemand. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
cbr(1), ondemand(2) |
|
| hcxDnStrmRate |
1.3.6.1.4.1.1141.2.10.1.1.4 |
| peak bits per second in the downstream direction. Policing/shaping of this attribute is the responsibility of the appropriate Ethernet card. Setting this value to 0 will have the effect of stopping downstream traffic. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0..11560000 |
|
| hcxUpStrmType |
1.3.6.1.4.1.1141.2.10.1.1.5 |
| defines CBR or ondemand in the upstream direction. This attribute controls the type of minimum cell traffic. Default is ondemand. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
cbr(1), ondemand(2) |
|
| hcxUpStrmMinRate |
1.3.6.1.4.1.1141.2.10.1.1.6 |
| bits per second in the upstream direction. Policing/shaping of this attribute is the responsibility of the appropriate RX card. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0..1650000 |
|
| hcxUpStrmMaxRate |
1.3.6.1.4.1.1141.2.10.1.1.7 |
| peak bits per second in the upstream direction. This is a best-effort rate. Policing/shaping of this attribute is the responsibility of the appropriate RX card. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0..1650000 |
|
| hcxServTypeDelete |
1.3.6.1.4.1.1141.2.10.1.1.8 |
| The ComController Service Type Delete is an active-value. The setting of this value to execute(2) causes the multicast list entry to be deleted. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
nil(1), execute(2) |
|
| hcxArpServerTrapEnable |
1.3.6.1.4.1.1141.2.12.1 |
| specifies if traps should be generated when user impersonation of ComController server IP addresses is detected. Default false. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
true(1), false(2) |
|
| hcxArpUserTrapEnable |
1.3.6.1.4.1.1141.2.12.2 |
| controls if traps should be generated when user specifies an incorrect IP address in an ARP message. Default false. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
true(1), false(2) |
|
| hcxStuDefaultAuth |
1.3.6.1.4.1.1141.2.13.1 |
| Indicates whether the default authorization of a previously unconfigured and unauthorized ComPort should be permitted. If true, then all other attributes in this group must be set. Note that this feature CANNOT be enabled if hcxStuAltDownFreqEnable is set to true. Default false. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
true(1), false(2) |
|
| hcxStuDefaultServType |
1.3.6.1.4.1.1141.2.13.2 |
| Contains the default QoS group for an acquired but unconfigured/unauthorized ComPort. Once configured, then the appropriate service type defined for the particular ComPort shall be used. 0 indicates no default QoS group to be used. Default 0. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0..16 |
|
| hcxStuDefaultVlan |
1.3.6.1.4.1.1141.2.13.3 |
| Contains the default VLAN id for an acquired but unconfigured/unauthorized ComPort. Once configured, then the appropriate VLAN id defined for the particular ComPort shall be used. 0 indicates no default VLAN id to be used. Default 0. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0..64 |
|
| hcxStuDefCom21SwImage |
1.3.6.1.4.1.1141.2.13.4 |
| Contains the default software image for an acquired but unconfigured/unauthorized ComPort. Once configured, then the appropriate software image defined for the particular ComPort shall be used. Null string indicates no default software image to be used. Default null string. |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
SIZE(16) |
|
| hcxStuDef3ComSwImage |
1.3.6.1.4.1.1141.2.13.5 |
| Contains the default software image for an acquired but unconfigured/unauthorized 3COM modem. Once configured, then the appropriate software image defined for the particular 3COM modem shall be used. Null string indicates no default software image to be used. Default null string. |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
SIZE(16) |
|
| hcxDbAction |
1.3.6.1.4.1.1141.2.14.1 |
| This attribute is used to control various database actions. saveDb causes the present active database to be saved to disk. This will overwrite any previously saved database. revertToPeriodicDb causes the periodically saved database to become the active database. revertToSavedDb causes the user saved database to become the active database. deleteSavedDb and deletePeriodicDb simply delete the current saved and periodic database respectively. In the case of these last two options, the CC shall reboot. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
nil(1), saveDb(2), deleteSavedDb(3), deletePeriodicDb(4), revertToPeriodicDb(5), revertToSavedDb(6) |
|
| hcxDbActionResult |
1.3.6.1.4.1.1141.2.14.2 |
| This attribute contains the result of the last hcxDbAction. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
inprogress(1), success(2), diskFailure(3), noDatabaseFound(4), invalidDatabase(5) |
|
| hcxDbBackupPeriod |
1.3.6.1.4.1.1141.2.14.3 |
| the period, in hours, at which the database will be automatically saved on the disk. 0 will disable the auto backup. Default 24. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0..24 |
|
| hcxFileTransProt |
1.3.6.1.4.1.1141.2.18.1 |
| specifies the type of protocol used for file transfer. i.e. for config_db and images. This information is stored in NVRAM. Note that a upon boot, if there is no valid CC image, an TFTP will be attempted regardless of the setting of this attribute. Default is ftp. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
ftp(1), tftp(2) |
|
| hcxFileServerCntrl |
1.3.6.1.4.1.1141.2.18.2 |
| specifies how the file server address is obtained. This parameter is controlled by CC Boot shell line. Can elect to use bootp or allow the operator to explicitly specify. Note that if this attribute is set to mibSpecified then no bootp should be generated by the boot or runtime code. This information is stored in NVRAM. Default is bootp. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
bootp(1), mibSpecified(2) |
|
| hcxImageServerIpAddr |
1.3.6.1.4.1.1141.2.18.3 |
| IP address of the image file server. This attribute is writeable only if hcxFileServerCntrl is set to mibSpecified. Otherwise it is a read-only attribute detailing the IP address returned by bootp. This attribute is held in NVRAM. Default is 0.0.0.0. |
| OBJECT-TYPE |
|
|
|
| |
IpAddress |
|
|
| hcxImageServerPath |
1.3.6.1.4.1.1141.2.18.4 |
| specifies path to the image files. This attribute is writeable only if hcxFileServerCntrl is set to mibSpecified. Otherwise it is a read-only attribute detailing the path returned by bootp. This attribute is held in NVRAM. Default is null string. |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
SIZE(32) |
|
| hcxImageServerLogin |
1.3.6.1.4.1.1141.2.18.5 |
| specifies a login to the image server. This attribute is only applicable if hcxFileServerCntrl is set to mibSpecified and hcxFileTransProt is set to ftp. This attribute is held in NVRAM. Default is ftp. |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
SIZE(16) |
|
| hcxImageServerPassword |
1.3.6.1.4.1.1141.2.18.6 |
| specifies a password to the image server. This attribute is only applicable if hcxFileServerCntrl is set to mibSpecified and hcxFileTransProt is set to ftp. This attribute is held in NVRAM. Default is anonymous. |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
SIZE(16) |
|
| hcxDatabaseServerIpAddr |
1.3.6.1.4.1.1141.2.18.7 |
| IP address of the server on which to save and retrieve the config database. This attribute is only applicable if hcxFileServerCntrl is set to mibSpecified. Default is 0.0.0.0. |
| OBJECT-TYPE |
|
|
|
| |
IpAddress |
|
|
| hcxDatabaseServerPath |
1.3.6.1.4.1.1141.2.18.8 |
| specifies path and the name of the config database file. This attribute is only applicable if hcxFileServerCntrl is set to mibSpecified. Default is null string. |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
SIZE(32) |
|
| hcxDatabaseServerLogin |
1.3.6.1.4.1.1141.2.18.9 |
| specifies a login to the Database server. This attribute is only applicable if hcxFileServerCntrl is set to mibSpecified and hcxFileTransProt is set to ftp. Default is ftp. |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
SIZE(16) |
|
| hcxDatabaseServerPassword |
1.3.6.1.4.1.1141.2.18.10 |
| specifies a password to the Database server. This attribute is only applicable if hcxFileServerCntrl is set to mibSpecified and hcxFileTransProt is set to ftp. Default is anonymous. |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
SIZE(16) |
|
| hcxCardRemClear |
1.3.6.1.4.1.1141.4.121 |
| generated whenever a card is reinserted in a slot or when a slot is configured to empty or when a slot is reassigned, and that slot has a previously generated hcxCardRemoved trap. If the inserted card is of the incorrect type, then a subsequent hcxMismatchDetect trap will be generated. Severity is CLEARED. |
| NOTIFICATION-TYPE |
|
|
|
| |
hcxAlmSeverity |
|
|
| |
hcxEventLogTime |
|
|
| |
hcxShelfNo |
|
|
| |
hcxSlotId |
|
|
Defined Objects
| HcxCardType |
|
| INTEGER |
rx(1), tx(2), ethDual10bT(3), ethQuad10bT(4), eth100bT(5), tele(6), cc(7), oc3(8), atm25(9), empty(10), txRf(11), txDig(12), eth10bT8k(13), intConn(14), rxm(15), atmlSw(16), compactSw(17) |
|
|
| HcxTrapReceiverEntry |
|
| SEQUENCE |
|
|
|
| |
INTEGER as hcxTrapRcvrStatus |
|
|
| |
IpAddress as hcxTrapRcvrNetAddress |
|
|
| |
OCTET STRING as hcxTrapRcvrComm |
|
|
| |
TimeTicks as hcxTrapRcvrAgeTime |
|
|
| HcxShelfEntry |
|
| SEQUENCE |
|
|
|
| |
INTEGER as hcxShelfId |
|
|
| |
Integer32 as hcxShelfNoSlots |
|
|
| HcxSlotEntry |
|
| SEQUENCE |
|
|
|
| |
INTEGER as hcxShelfNo |
|
|
| |
INTEGER as hcxSlotId |
|
|
| |
INTEGER as hcxSlotSupportedTypes |
|
|
| |
HcxCardType as hcxSlotConfigCardType |
|
|
| |
HcxCardType as hcxSlotInsertCardType |
|
|
| HcxImageListEntry |
|
| SEQUENCE |
|
|
|
| |
INTEGER as hcxImageId |
|
|
| |
INTEGER as hcxImageType |
|
|
| |
DisplayString as hcxImageFilename |
|
|
| |
DisplayString as hcxSwRevision |
|
|
| |
DisplayString as hcxHwRevision |
|
|
| |
DisplayString as hcxFwRevision |
|
|
| |
INTEGER as hcxImageState |
|
|
| HcxServTypeEntry |
|
| SEQUENCE |
|
|
|
| |
Integer32 as hcxServiceTypeId |
|
|
| |
DisplayString as hcxServTypeDesc |
|
|
| |
INTEGER as hcxDnStrmType |
|
|
| |
INTEGER as hcxDnStrmRate |
|
|
| |
INTEGER as hcxUpStrmType |
|
|
| |
INTEGER as hcxUpStrmMinRate |
|
|
| |
INTEGER as hcxUpStrmMaxRate |
|
|
| |
INTEGER as hcxServTypeDelete |
|
|