
| RFC1155-SMI | RFC-1212 | RFC1213-MIB |
| GEN-MIB |
| IpAddress | Counter | TimeTicks |
| OBJECT-TYPE | DisplayString | lannet |
| chassis | 1.3.6.1.4.1.81.7 | ||
| OBJECT IDENTIFIER | |||
| chHWType | 1.3.6.1.4.1.81.7.1 | ||
| Indicates type of enclosure in which the SNMP agent operates. | |||
| OBJECT-TYPE | |||
| INTEGER | let18(1), let3(2), let36(3), let18Extended(4), lert40(5), let10(6), fdx100(7), stack(8), let20(9), let36-01-02(10), lea(11), lac(12), visage(13), letM770(14), m770(15), m770Atm(16), cajunP120(17), cajunP330(18), cajunP130(19), unknown(255) | ||
| chNumberOfSlots | 1.3.6.1.4.1.81.7.2 | ||
| Number of manageable slots in the chassis. In implementation it describes the number of manageable slots in the chassis (not all slots should be occupied). | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| chNumberOfEthernetBuses | 1.3.6.1.4.1.81.7.3 | ||
| Indicates the number of internal Ethernet buses provided by the box. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..255 | ||
| chNumberOfTRBuses | 1.3.6.1.4.1.81.7.4 | ||
| Indicates the number of internal Token Ring buses provided by the box. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..255 | ||
| chNumberOfFDDIBuses | 1.3.6.1.4.1.81.7.5 | ||
| Indicates the number of internal FDDI buses provided by the box. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..255 | ||
| chNumberOfLocalTalkBuses | 1.3.6.1.4.1.81.7.6 | ||
| Indicates the number of internal Local Talk buses provided by the box. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..255 | ||
| chReset | 1.3.6.1.4.1.81.7.7 | ||
| Setting the value of this attribute to ON is interpreted as a reset command for the whole chassis. It initiates a complete reinitialisation of the chassis and of all the devices incorporated inside the chassis. | |||
| OBJECT-TYPE | |||
| INTEGER | on(1), off(2) | ||
| chFullConfig | 1.3.6.1.4.1.81.7.8 | ||
| Full configuration message retrieved by management stations at periodic interrogation times. Coded in compact internal application format. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| chAg | 1.3.6.1.4.1.81.7.9 | ||
| OBJECT IDENTIFIER | |||
| chGenAgTable | 1.3.6.1.4.1.81.7.9.1 | ||
| Table of configuration attributes common to all SNMP agents in hubs. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ChGenAgEntry | |||
| chGenAgEntry | 1.3.6.1.4.1.81.7.9.1.1 | ||
| An entry in the table, containing configuration attributes for a single agent. | |||
| OBJECT-TYPE | |||
| ChGenAgEntry | |||
| chGenAgId | 1.3.6.1.4.1.81.7.9.1.1.1 | ||
| Agent index for identifying the agent. Takes the value of the slot number where the agent card is inserted. For box agents which are not managed as Group the value of chGenAgId is chNumberOfSlots+1. For box agents which are managed as Group the value in not greater then chNumberOfSlots | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| chGenAgType | 1.3.6.1.4.1.81.7.9.1.1.2 | ||
| Defines the type of the card whose management attributes are described by the SNMP agent. | |||
| OBJECT-TYPE | |||
| INTEGER | nma1-et(1), nma1-et-e(2), nma1-tr(3), nma2-et(4), nma2-tr(5), nma2-fddi(6), ielb(7), itlb(8), lts16(9), ierp(10), iefn(11), itfn(12), sh-ema(13), nma-rt(14), sh-tma(15), nma-re(16), ietlb(17), nma2-fddi-rad(18), iefr-mc(19), iefr-utp(20), ieqr(21), iere(22), itre(23), las(24), lsa(26), lsf100(27), nma-rs(28), lea(29), itrp(30), ls3ls(31), visageNMA(32), fat-pipe-fddi(33), visage16200(34), visage16TR(35), visage16155(36), lsa2(39), m-spv(40), m-mls(41), m-atm(42), m-spx(43), cajunP120(44), cajunP330(45), m-sps-T(46), m-sps-ER(47), m-sps-EB(48), cajunP122(49), cajunP333R(50), cajunX330ATM(51), cajunP130(52), m-acc(53), cajunP332-ML(54), cajunP333RLB(55), c-Hawk(56), unknown(255) | ||
| chGenAgMgmtIfType | 1.3.6.1.4.1.81.7.9.1.1.3 | ||
| This attribute describes one of the interfaces of agents existing on modules and their type. Value 'none' defines the lack of an interface whose type is recognized by the management console. Any other value defines an interface whose type is recognized by the management console and may be used as a management channel. | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), regular1822(2), hdh1822(3), ddn-x25(4), rfc877-x25(5), ethernet-csmacd(6), iso88023-csmacd(7), iso88024-tokenBus(8), iso88025-tokenRing(9), iso88026-man(10), starLan(11), proteon-10MBit(12), proteon-80MBit(13), hyperchannel(14), fddi(15), lapb(16), sdlc(17), t1-carrier(18), cept(19), basicIsdn(20), primaryIsdn(21), propPointToPointSerial(22), ppp(23), softwareLoopback(24), eon(25), ethernet-3Mbit(26), nsip(27), slip(28), ultra(29), ds3(30), sip(31), frameRelay(32), rs232(33), para(34), arcnet(35), arcnetPlus(36), atm(37), miox25(38), sonet(39), x25ple(40), iso88022llc(41), localTalk(42), smdsDxi(43), frameRelayService(44), v35(45), hssi(46), hippi(47), modem(48), aal5(49), sonetPath(50), sonetVT(51), smdsIcip(52), propVirtual(53), propMultiplexor(54), aflane8023(59), ip(255) | ||
| chGenAgAddr | 1.3.6.1.4.1.81.7.9.1.1.4 | ||
| This attribute defines an unique address by which the agent may be addressed by the management console. The address format should be consistent with the type defined by chGenAgMgmtIfType. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..20) | ||
| chGenAgSpecificOID | 1.3.6.1.4.1.81.7.9.1.1.5 | ||
| This attribute provides the OID of another group containing additional more specific information regarding this instance. | |||
| OBJECT-TYPE | |||
| OBJECT IDENTIFIER | |||
| chGenAgSLIPAddress | 1.3.6.1.4.1.81.7.9.1.1.6 | ||
| IP address of the SLIP channel of the agent | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| chGenAgTypeName | 1.3.6.1.4.1.81.7.9.1.1.7 | ||
| String with the Agent name. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..32) | ||
| chGenAgEntMngVersion | 1.3.6.1.4.1.81.7.9.1.1.8 | ||
| The entity management version supported by the specific Agent. In the format: X.Y.Z (using numbers): 1st byte - major version number 2nd byte - '.' 3rd byte - minor version number 4th byte - '.' 5th byte - debug version number. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| chGenAgIpAddr | 1.3.6.1.4.1.81.7.9.1.1.9 | ||
| This attribute defines the Ip address by which the agent may be addressed by the management console. For NMA-RX this should include the IP address of the Side Band interface. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| chLntAgTable | 1.3.6.1.4.1.81.7.9.2 | ||
| Table of configuration attributes of SNMP box agents in hubs. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ChLntAgEntry | |||
| chLntAgEntry | 1.3.6.1.4.1.81.7.9.2.1 | ||
| An entry in the table, containing configuration attributes for a single box agent. | |||
| OBJECT-TYPE | |||
| ChLntAgEntry | |||
| chLntAgId | 1.3.6.1.4.1.81.7.9.2.1.1 | ||
| Agent index for identifying the agent. Identical to the index in chGenAgTable for the described agent. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| chLntAgSLIPAddress | 1.3.6.1.4.1.81.7.9.2.1.2 | ||
| IP address of the SLIP channel of the agent | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| chLntAgSWVersion | 1.3.6.1.4.1.81.7.9.2.1.3 | ||
| ASCII string for description and display of the agent software version. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| chLntAgKernelVersion | 1.3.6.1.4.1.81.7.9.2.1.4 | ||
| ASCII string for description and display of the agent operating system (kernel) version. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| chLntAgCoprocSWVersion | 1.3.6.1.4.1.81.7.9.2.1.5 | ||
| ASCII string describing the software version of the agent's coprocessor. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| chLntAgSWFault | 1.3.6.1.4.1.81.7.9.2.1.6 | ||
| System fault emitted by agent software. It covers faults detected by the agent operating system and drivers. EnterpriseSpecific traps mechanism is used for transfering these traps to the management system. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| chLntAgMgmtBusSelection | 1.3.6.1.4.1.81.7.9.2.1.7 | ||
| Attribute describing the number of the bus on which management data are reported. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| chLntAgCoprocCommStatus | 1.3.6.1.4.1.81.7.9.2.1.8 | ||
| Attribute describing the status of the communication between the agent and its coprocessor. | |||
| OBJECT-TYPE | |||
| INTEGER | ok(1), commProblems(2), timeout(3), notSupported(255) | ||
| chLntAgCommDebugMode | 1.3.6.1.4.1.81.7.9.2.1.9 | ||
| Attribute describing the agent mode in which communication problem traps are sent to managers (value 'on') or are not sent to managers (value 'off'). | |||
| OBJECT-TYPE | |||
| INTEGER | on(1), off(2) | ||
| chLntAgConfigChangeTraps | 1.3.6.1.4.1.81.7.9.2.1.10 | ||
| The value of this attributes determines whether or not the agent sends Configuration Change traps to the manager. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| chLntAgFaultTraps | 1.3.6.1.4.1.81.7.9.2.1.11 | ||
| The value of this attributes determines whether or not the agent sends Fault traps to the manager. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| chLntAgTrafficThreshTraps | 1.3.6.1.4.1.81.7.9.2.1.12 | ||
| The value of this attributes determines whether or not the agent sends Traffic Threshold traps to the manager. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| chLntAgGroupEnrollDeenrollTraps | 1.3.6.1.4.1.81.7.9.2.1.13 | ||
| The value of this attributes determines whether or not the agent sends Group Enrollment and Group Deenrollment traps to the manager. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| chLntAgSoftFaultTraps | 1.3.6.1.4.1.81.7.9.2.1.14 | ||
| The value of this attributes determines whether or not the agent sends Software Fault traps to the manager. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| chLntAgHubEnrollTraps | 1.3.6.1.4.1.81.7.9.2.1.15 | ||
| The value of this attributes determines whether or not the agent sends periodic Hub Enrollment traps to the manager. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| chLntAgTempThreshTraps | 1.3.6.1.4.1.81.7.9.2.1.16 | ||
| The value of this attributes determines whether or not the agent sends Temperature Threshold traps to the manager. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| chLntAgSpecificOID | 1.3.6.1.4.1.81.7.9.2.1.17 | ||
| This attribute provides the OID of another group containing additional more specific information regarding this instance. | |||
| OBJECT-TYPE | |||
| OBJECT IDENTIFIER | |||
| chLntAgLastAddrConfig | 1.3.6.1.4.1.81.7.9.2.1.18 | ||
| Configuration attribute describing the last physical address detected at each port. Coded in internal application format. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| chLntAgSecAddrConfig | 1.3.6.1.4.1.81.7.9.2.1.19 | ||
| Configuration attribute describing the configuration of the secure addresses. Coded in internal application format. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| chLntAgSoftwareStatus | 1.3.6.1.4.1.81.7.9.2.1.20 | ||
| Describes configuration of the firmware on this agent. unLoadable(1) - is returned by agents which do not support the Software Download feature; loaded(2) - is returned by agents with loaded software; downLoading(3) - when the attribute is set to this value by manager, it triggers the Software Download procedure. When procedure finished, agent software will reestablish value 'loaded(2)'. downLoadOfDownload (4) - when the attribute is set to this value by manager, it causes the Agent to download the new download software. When procedure finished, agent software will reestablish value 'loaded(2)'. | |||
| OBJECT-TYPE | |||
| INTEGER | unLoadable(1), loaded(2), downLoading(3), downLoadOfDownload(4), notSupported(255) | ||
| chLntAgConfigurationSymbol | 1.3.6.1.4.1.81.7.9.2.1.21 | ||
| Defines the Configuration Symbol attached to any hardware module manufactured. One single character A..Z defines the CS version. For older modules which did not support this option on SNMP character '*' will be returned. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(1) | ||
| chLntAgIntTemp | 1.3.6.1.4.1.81.7.9.2.1.22 | ||
| Internal temperature measured by the temperature sensor placed on the agent card. Expressed in Celsius degrees.Value '999' means not supported. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| chLntAgBootVersion | 1.3.6.1.4.1.81.7.9.2.1.23 | ||
| ASCII string for description and display of the agent boot software version. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| chLntAgSensorFault | 1.3.6.1.4.1.81.7.9.2.1.24 | ||
| A code of a sensor fault discovered by the agent. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| chLntAgSensorFaultTraps | 1.3.6.1.4.1.81.7.9.2.1.25 | ||
| This attribute enables/disables generation of the sensor fault trap. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| chLntAgInterProcFault | 1.3.6.1.4.1.81.7.9.2.1.26 | ||
| A code of intercommunication fault between Main - Master processors. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| chLntAgInterProcFaultTraps | 1.3.6.1.4.1.81.7.9.2.1.27 | ||
| This attribute enables/disables generation of the intercommunication fault trap. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| chLntAgPSUVoltThrsTraps | 1.3.6.1.4.1.81.7.9.2.1.28 | ||
| The value of this attribute determines whether or not the agent sends PSU voltage threshold traps to the manager. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| chLntAgHardwareVersion | 1.3.6.1.4.1.81.7.9.2.1.29 | ||
| ASCII string for description and display of the agent hardware version. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| chLntAgSoftwareDscr | 1.3.6.1.4.1.81.7.9.2.1.30 | ||
| ASCII string for description and display of the agent software information. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| chLntAgCAMChangeTraps | 1.3.6.1.4.1.81.7.9.2.1.31 | ||
| The value of this attribute determines whether or not the agent sends CAM last change traps to the manager. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| chLntAgAppVersion | 1.3.6.1.4.1.81.7.9.2.1.32 | ||
| ASCII string for description and display of the agent's application version. e.g. software running top of the Kernel | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| chLntAgSetup | 1.3.6.1.4.1.81.7.9.3 | ||
| OBJECT IDENTIFIER | |||
| chLntAgMaxNmbOfMngrs | 1.3.6.1.4.1.81.7.9.3.1 | ||
| Maximum number of permanent managers. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| chLntAgPermMngrTable | 1.3.6.1.4.1.81.7.9.3.2 | ||
| Table of permanent managers. The Agent will send Traps to managers listed in the chLntAgPermMngrTable. A Trap will be send to the manager according to the Trap Enable/Disable flag related to the Trap. A permanent manager will be defined by the user, through the Agent setup procedure, or by SNMP request. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ChLntAgPermMngrEntry | |||
| chLntAgPermMngrEntry | 1.3.6.1.4.1.81.7.9.3.2.1 | ||
| An entry in the permanent managers table. | |||
| OBJECT-TYPE | |||
| ChLntAgPermMngrEntry | |||
| chLntAgPermMngrId | 1.3.6.1.4.1.81.7.9.3.2.1.1 | ||
| Index in the permanent managers table. It ranges from 1 to chLntAgMaxNmbOfMngrs | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| chLntAgPermMngrAddr | 1.3.6.1.4.1.81.7.9.3.2.1.2 | ||
| IP address of a permanent manager. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| chLntAgMngrTraps | 1.3.6.1.4.1.81.7.9.3.2.1.3 | ||
| Value 'on' indicates that SNMP agent should send SNMP traps (traffic excluded) to the manager. | |||
| OBJECT-TYPE | |||
| INTEGER | on(1), off(2) | ||
| chLntAgMaxNmbOfNets | 1.3.6.1.4.1.81.7.9.3.3 | ||
| Maximum number of remote networks. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| chLntAgRmtNetTable | 1.3.6.1.4.1.81.7.9.3.4 | ||
| Remote networks table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ChLntAgRmtNetEntry | |||
| chLntAgRmtNetEntry | 1.3.6.1.4.1.81.7.9.3.4.1 | ||
| Entry in the remote networks table. | |||
| OBJECT-TYPE | |||
| ChLntAgRmtNetEntry | |||
| chLntAgRmtNetId | 1.3.6.1.4.1.81.7.9.3.4.1.1 | ||
| Index of a remote network. It ranges from 1 to chLntAgMaxNmbOfNets. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| chLntAgRmtNetAddr | 1.3.6.1.4.1.81.7.9.3.4.1.2 | ||
| Address of a remote network. The host portion is always 0. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| chLntAgRmtNetMask | 1.3.6.1.4.1.81.7.9.3.4.1.3 | ||
| Subnet mask for the remote network. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| chLntAgDateTime | 1.3.6.1.4.1.81.7.9.3.5 | ||
| Current date and time for NMA-TR. The format is YYMMDDhhmmssw, where w - day of the week e.g., 1=Mon, 2=Tue,..., 7=Sun. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(13) | ||
| chLntAgReset | 1.3.6.1.4.1.81.7.9.3.6 | ||
| This attribute enables the user to reset the agent. | |||
| OBJECT-TYPE | |||
| INTEGER | on(1), off(2) | ||
| chLntAgTrapsTable | 1.3.6.1.4.1.81.7.9.3.7 | ||
| Table of traps for each permanent manager. A Trap will be send to the manager according to the Trap Enable/Disable flag related to the Trap ID. When adding a new manager to the permanent managers table, the Agent will set its entry in this table with the default value for each trap flag. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ChLntAgTrapsEntry | |||
| chLntAgTrapsEntry | 1.3.6.1.4.1.81.7.9.3.7.1 | ||
| An entry in the permanent managers table. | |||
| OBJECT-TYPE | |||
| ChLntAgTrapsEntry | |||
| chLntAgTrapsPermMngrId | 1.3.6.1.4.1.81.7.9.3.7.1.1 | ||
| Index in the permanent managers traps table. It ranges from 1 to chLntAgMaxNmbOfMngrs | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| chLntAgTrapsId | 1.3.6.1.4.1.81.7.9.3.7.1.2 | ||
| The trap number is the second index in the table. The following list conclude the available traps numbers to be configured by the manager: 1: Configuration Change Traps. Default = enabled(1). 2: Fault Traps. Default = enabled(1). 3: Traffic Threshold Exceeded Traps. Default = enabled(1). 4: Group DeEnrollment Trap. Default = enabled(1). 6: Agent SW Fault Trap. Default = enabled(1). 8: Hub Enrollment Trap. Default = enabled(1). 14: Temperature Warning Traps. Default = disabled(2). 19: PSU Existance Trap. Default = disabled(2). 22: VNS. Default = disabled(2). | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| chLntAgTrapsEnableFlag | 1.3.6.1.4.1.81.7.9.3.7.1.3 | ||
| The value of this attributes determines whether or not the agent sends the traps to the manager. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| chLntAgTicksPerSecond | 1.3.6.1.4.1.81.7.9.3.8 | ||
| defines how many ticks are counted in one second. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| chLntAgMaxTrapsNumber | 1.3.6.1.4.1.81.7.9.3.100 | ||
| This attribute define the muximum trap number supported by the agent. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| chAgHubMgmtIfType | 1.3.6.1.4.1.81.7.9.4 | ||
| This attribute describes one of the interfaces of agents existing on modules and their type. Value 'none' defines the lack of an interface whose type is recognized by the management console. Any other value defines an interface whose type is recognized by the management console and may be used as a management channel. | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), regular1822(2), hdh1822(3), ddn-x25(4), rfc877-x25(5), ethernet-csmacd(6), iso88023-csmacd(7), iso88024-tokenBus(8), iso88025-tokenRing(9), iso88026-man(10), starLan(11), proteon-10MBit(12), proteon-80MBit(13), hyperchannel(14), fddi(15), lapb(16), sdlc(17), t1-carrier(18), cept(19), basicIsdn(20), primaryIsdn(21), propPointToPointSerial(22), ppp(23), softwareLoopback(24), eon(25), ethernet-3Mbit(26), nsip(27), slip(28), ultra(29), ds3(30), sip(31), frameRelay(32), rs232(33), para(34), arcnet(35), arcnetPlus(36), atm(37), miox25(38), sonet(39), x25ple(40), iso88022llc(41), localTalk(42), smdsDxi(43), frameRelayService(44), v35(45), hssi(46), hippi(47), modem(48), aal5(49), sonetPath(50), sonetVT(51), smdsIcip(52), propVirtual(53), propMultiplexor(54), ip(255) | ||
| chAgHubAddr | 1.3.6.1.4.1.81.7.9.5 | ||
| This attribute defines an unique address by which the agent may be addressed by the management console. The address format should be consistent with the type defined by chAgHubMgmtIfType. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..20) | ||
| chMgr | 1.3.6.1.4.1.81.7.10 | ||
| OBJECT IDENTIFIER | |||
| chMgrTrapRepStatus | 1.3.6.1.4.1.81.7.10.1 | ||
| Value 'on' indicates that SNMP agent should send SNMP traps (traffic ex- cluded) to the manager. | |||
| OBJECT-TYPE | |||
| INTEGER | on(1), off(2) | ||
| chMgrContPerfRep | 1.3.6.1.4.1.81.7.10.2 | ||
| Value 'on' indicates that the SNMP agent should send traffic SNMP traps to the manager. | |||
| OBJECT-TYPE | |||
| INTEGER | on(1), off(2) | ||
| chMgrMngmtState | 1.3.6.1.4.1.81.7.10.3 | ||
| Attribute to be set by manager in order to instruct the agent to enter into a management session with the console. Setting this value to 'on' has the effect of performing an 'I am your manager' action upon the agent. | |||
| OBJECT-TYPE | |||
| INTEGER | on(1), off(2) | ||
| chMgrPollInterval | 1.3.6.1.4.1.81.7.10.4 | ||
| The attribute defines an interval during which the agent is waiting for the manager's requests. Default value 5 minutes. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| chHW | 1.3.6.1.4.1.81.7.11 | ||
| OBJECT IDENTIFIER | |||
| chHWPSUTable | 1.3.6.1.4.1.81.7.11.1 | ||
| Table of configuration attributes for Power Supply Units. This table can be retrieved only from agents equipped with adequate hardware. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ChHWPSUEntry | |||
| chHWPSUEntry | 1.3.6.1.4.1.81.7.11.1.1 | ||
| An entry in the table, containing configuration attributes for a single Power Supply Unit. | |||
| OBJECT-TYPE | |||
| ChHWPSUEntry | |||
| chHWPSUId | 1.3.6.1.4.1.81.7.11.1.1.1 | ||
| PSU index for identifying the PSU. The index for each hub: Stackable: odd number - internal, even number - backup LET 36: 1 - lower; 2 - higher, LET 20: 1 - right; 2 - left, LET 10: 1 - main; 2 - backup. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| chHWPSUActivityStatus | 1.3.6.1.4.1.81.7.11.1.1.2 | ||
| This attribute defines the status of the PSU in what concerns supplying power to the chassis. NotActive(1) - indicates a disabled or defective PSU which cannot supply power to the chassis. Dormant(2) - indicates a functional PSU which is installed for backup purposes and can at any moment supply power to the devices in the chassis. Active(3) - indicates that the PSU supplies power to the chassis. Failed(4) - indicates PSU failure (new LET-36 and LET-20). Unknown(5) - when the PSU activity is not readable or unknown. NotExist(6) - indicates absence of PSU from the configuration. NoBackupPS(7) - indicates absence of Backup PSU from the configuration. The following values are supported for each hub: Stack: active, failed, notExist, noBackupPS LET-36: active, failed, notExist. LET-20: active, failed, notExist. LET-10: active, failed, unknown. | |||
| OBJECT-TYPE | |||
| INTEGER | notActive(1), dormant(2), active(3), failed(4), unknown(5), notExist(6), noBackupPS(7) | ||
| chHWPSULocation | 1.3.6.1.4.1.81.7.11.1.1.3 | ||
| Describes the location of the PSU: LET-36: lower, upper. LET-20: right, left. LET-10: unknown. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), internal(2), external(3), right(4), left(5), lower(6), upper(7), unknown(8), notExist(9), middle(10) | ||
| chHWPSUVoltage | 1.3.6.1.4.1.81.7.11.1.1.4 | ||
| Indicates voltage of PSU expressed in miliVolts. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| chHWPSUVoltHighThresh | 1.3.6.1.4.1.81.7.11.1.1.5 | ||
| Indicates voltage High threshold of the PSU in the HUB. The PSU output working voltage needed to support a module in the HUB should be V±5%. This value is hard-coded. The Agent will Trap the manager when the PSU will exceed the chHWPSUVoltHighThresh. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| chHWPSUVoltLowThresh | 1.3.6.1.4.1.81.7.11.1.1.6 | ||
| Indicates voltage Low threshold of the PSU in the HUB. The PSU output working voltage needed to support a module in the HUB should be V±5%. This value is hard-coded. The Agent will Trap the manager when the PSU will 'dive' lower than the chHWPSUVoltLowThresh . | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| chHWIntTempWarning | 1.3.6.1.4.1.81.7.11.2 | ||
| Fault condition indicating that the temperature measured by one of the sensors internal to the box exceeded chHWIntTempThresh. | |||
| OBJECT-TYPE | |||
| INTEGER | ok(1), exceeded(2) | ||
| chHWIntTempThresh | 1.3.6.1.4.1.81.7.11.3 | ||
| Internal enclosure temperature threshold value, expressed in degrees Celsius. When exceeded, a trap is sent to the management console. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| chHWPeakIntTemp | 1.3.6.1.4.1.81.7.11.4 | ||
| Maximum internal temperature inside the chassis. It is the maximum of the temperature values detected by different temperature sensors inside the box. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| chHWFans | 1.3.6.1.4.1.81.7.11.5 | ||
| This attribute describes the existence/absence of the fans in a hub. | |||
| OBJECT-TYPE | |||
| INTEGER | exist(1), notExist(2), notSupported(255) | ||
| chSlotLastChange | 1.3.6.1.4.1.81.7.12 | ||
| This attribute contains the value of sysUpTime at the time any of the modules in the hub was enrolled/deenrolled. In addition it will be updated when a module is reset | |||
| OBJECT-TYPE | |||
| TimeTicks | |||
| chAlarms | 1.3.6.1.4.1.81.7.13 | ||
| OBJECT IDENTIFIER | |||
| alarmPolicyTable | 1.3.6.1.4.1.81.7.13.1 | ||
| A table containing the parameters that define the alarm policies. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AlarmPolicyEntry | |||
| alarmPolicyEntry | 1.3.6.1.4.1.81.7.13.1.1 | ||
| An entry that contains the definition of an alarm: threshold value, threshold type (rising/falling), sample time interval, sample type (delta or absolute value), and action policy. | |||
| OBJECT-TYPE | |||
| AlarmPolicyEntry | |||
| alarmPolicyIndex | 1.3.6.1.4.1.81.7.13.1.1.1 | ||
| The value of this object identifies the alarmPolicy. It is also used in the VariableTable as a pointer from the sampled OID to the alarmPolicy defined on that item. This item uniquely identifies the policy and has a value between 1 and the maximum size of the table. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| alarmPolicyParameterOID | 1.3.6.1.4.1.81.7.13.1.1.2 | ||
| This variable defines the type of variable that this policy monitors. The value of the item is an non-instanciated OID from the following list: - chHWPeakIntTemp. - ethPortFramesReceivedOK. - ethPortRunts. - ethPortPacketErrors. - ethPortCollisions. - ethPortPartitions. - ethPortPygmys. - ethGroupTotalErrors. - ethBusTotalCollisions. - ethBusTotalPackets. - ethBusTotalErrors. - ethBusUtilization. - tokRingUtilization. - dot5StatsLostFrameErrors. - dot5StatsSoftErrors. - dot5StatsHardErrors. - lsBusStatsPkts. - lsBusStatsUtilization. - lsBusStatsEthBroadcastPkts. - lsBusStatsEthMulticastPkts. - lsBusStatsGoodEthPkts. - lsBusStatsBadEthPkts. - lsBusStatsNonEthPkts - lsBusStatsPriorityPkts (1-4) - portInPkts. - portInTotalErrors. If the value of this item is not one of the above, or if it is one of the above but the item is not supported by the agent (such as a TR counter for a hub managed by an Ethernet agent), then when the row's status is changed to valid(1) a genErr will be returned. | |||
| OBJECT-TYPE | |||
| OBJECT IDENTIFIER | |||
| alarmPolicyRisingFalling | 1.3.6.1.4.1.81.7.13.1.1.3 | ||
| This value defines whether the policy is a rising alarm or a falling alarm. If the value of this item is rising(1), then the actionPolicy is executed if the value of the sampled variable is larger than the threshold. If the value of this item is falling(2), the actionPolicy is executed if the value of the sampled OID is smaller than or equal to the threshold. | |||
| OBJECT-TYPE | |||
| INTEGER | rising(1), falling(2) | ||
| alarmPolicyThresholdValue | 1.3.6.1.4.1.81.7.13.1.1.4 | ||
| The threshold value of the alarmPolicy. If the reading of the sampled instance (according to the alarmPolicyType: delta or absolute value) is above or below the value of this item (according to alarmPolicyRisingFalling), the alarmPolicyActionPolicy is carried out. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| alarmPolicySampleTimeInterval | 1.3.6.1.4.1.81.7.13.1.1.5 | ||
| The time interval between two subsequent samples of the data, in seconds. All instances that are assigned to this policy are sampled once every TimeInterval. The value of this item must be a multiple of 10 and smaller than 10,000. The agent will truncate values within the range to multiples of 10. An attempt to write values that are out of range will result in a badValue error. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| alarmPolicySampleType | 1.3.6.1.4.1.81.7.13.1.1.6 | ||
| This item defines the type of sample that is compared to the threshold. If the value of this item is delta(1), then the threshold is compared to the difference between every two consecutive samples of the variable. If the value is absoluteValue(2), it is compared to the value of the variable. The default value is delta(1). | |||
| OBJECT-TYPE | |||
| INTEGER | delta(1), absoluteValue(2) | ||
| alarmPolicyActionPolicy | 1.3.6.1.4.1.81.7.13.1.1.7 | ||
| This item defines the action taken by the agent upon detection of a variable larger or smaller than threshold (according to the value of alarmPolicyRisingFalling). If the value is trap(1) a trap is sent to all managers. If the value is trapAndDisconnectPort(2) and the OID in variableSampledOID points to a port then the port is disconnected. A value of (2) on a non-port item is legal, and will have the same effect as (1). Traps are sent only once, upon detection of the threshold crossing. | |||
| OBJECT-TYPE | |||
| INTEGER | trap(1), trapAndDisconnectPort(2), none(3) | ||
| alarmPolicyBitmap | 1.3.6.1.4.1.81.7.13.1.1.8 | ||
| This item describes the relationship between the policy table and the variable table. It is coded in proprietary coding. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| alarmPolicyStatus | 1.3.6.1.4.1.81.7.13.1.1.9 | ||
| This variable defines the status of the row. The values of this variables are defined and handled, according to the definitions in the IETF draft: Row creation with SNMPv1, from 19 October 1993. The createAndGo value is not supported. | |||
| OBJECT-TYPE | |||
| INTEGER | active(1), notInService(2), notReady(3), createAndWait(4), destroy(5) | ||
| alarmPolicyNextFree | 1.3.6.1.4.1.81.7.13.2 | ||
| An entry that points to the first available row in the policy table. If no rows are available, the value of the item is 0. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| variableTable | 1.3.6.1.4.1.81.7.13.3 | ||
| This table contains the instances to be sampled by the agent and a pointer to the relevant policy in the policyTable for each instance. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| VariableEntry | |||
| variableEntry | 1.3.6.1.4.1.81.7.13.3.1 | ||
| An entry that contains a single variable and the pointer to the policy by which it is monitored. | |||
| OBJECT-TYPE | |||
| VariableEntry | |||
| variablePolicy | 1.3.6.1.4.1.81.7.13.3.1.1 | ||
| This item points to the alarm policy that is executed on the variable defined in this row. There is no limitation on the number of variables that are assigned a given policy. It is possible to create rows in the variable table only if the policy pointed to is either active or notInService. When a row in the policy table is destroyed, all rows in the variable table that point to it will also be destroyed. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| variableInstance1 | 1.3.6.1.4.1.81.7.13.3.1.2 | ||
| This item defines the first index of the variable to be sampled. The combination of this item with variableInstance2 and with the alarmPolicyParameterOID (pointed to by variablePolicy) defines the instance to be sampled by the agent. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| variableInstance2 | 1.3.6.1.4.1.81.7.13.3.1.3 | ||
| This item is the second index of the variable to be sampled. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| variableStatus | 1.3.6.1.4.1.81.7.13.3.1.4 | ||
| This variable defines the status of the row. The values of this variables are defined and handled, according to the definitions in the IETF draft: Row creation with SNMPv1, from 19 October 1993. The createAndGo value is not supported. | |||
| OBJECT-TYPE | |||
| INTEGER | active(1), notInService(2), notReady(3), createAndWait(4), destroy(5) | ||
| variableNumOfEntries | 1.3.6.1.4.1.81.7.13.4 | ||
| The number of entries in the table. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| alarmPolicyLastChange | 1.3.6.1.4.1.81.7.13.5 | ||
| This attribute contains the value of sysUpTime at the last time any of the following changes were made to one of the alarm tables: - a policy's state was changed to or from 'active'; - a variable's state was changed to or from 'active'. | |||
| OBJECT-TYPE | |||
| TimeTicks | |||
| chThresholdStatus | 1.3.6.1.4.1.81.7.14 | ||
| This item is a bitmap that defines the threshold status of the hub, in relation to the alarmPolicyTable. If the hub is monitored by the agent according to policy number x in the alarmPolicyTable, and the threshold condition has occurred, then the bit #x in this item will have the value '1'. Otherwise it will be '0'. For x-186 based agents all bits of this item are '0'. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(4) | ||
| chLsPortList | 1.3.6.1.4.1.81.7.15 | ||
| A list of all LANswitch ports in the hub. 16 bits in the bitmap are allocated for each slot in the hub. The MSB is for port 1 of slot 1, and the LSB is for port 16 of slot 16. For ports which are in the hub the value of the bit is 1, otherwise 0. For XSwitches, 64 bits will be reserved for each slot. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(112) | ||
| chLsCAMPortList | 1.3.6.1.4.1.81.7.16 | ||
| A list of all LANswitch ports in the hub for which the contents of the CAM (list of MAC addresses detected at the LANSwitch Port) are currently available. 16 bits in the bitmap are allocated for each slot in the hub. The MSB is for port 1 of slot 1, and the LSB is for port 16 of slot 16. For ports which report the CAM the value of the bit is 1, otherwise 0. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(32) | ||
| chNumberOfHighSpeedBuses | 1.3.6.1.4.1.81.7.17 | ||
| Indicates the number of internal highspeed buses provided by the box. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..255 | ||
| chGroupList | 1.3.6.1.4.1.81.7.18 | ||
| The function of this variable is to summarize the information concerning the presence of the module and the module type for each slot of the hub. The information is coded as follows: First Octet: number of slots Second Octet: SNMP Type of information: Integer = 2, OctetString = 4. Third Octet: length of each field Fourth Octet: if no module in slot #1 so '0', else the module type i.e, the integer conrresponding to genGroupType. Last Octet: represents last slot and should contain the agent type. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| chNumberOfXSwitches | 1.3.6.1.4.1.81.7.19 | ||
| Indicats the number of XSwitches provided by the box. Default value for Visage hub is 1. Default value for Meritage hub is 2 | |||
| OBJECT-TYPE | |||
| INTEGER | 0..255 | ||
| lsBusThresholdStatus | 1.3.6.1.4.1.81.7.20 | ||
| This item is a bitmap that defines the threshold status of the highspeed bus, in relation to the alarmPolicyTable. If the bus is monitored by the agent according to policy number x in the alarmPolicyTable, and the threshold condition has occured, then the bit #x in this item will have the value '1'. Otherwise it will be '0'. For Agent other than NMA-RS, the value of this item is always 0. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(4) | ||
| chPluginList | 1.3.6.1.4.1.81.7.21 | ||
| The function of this variable is to summarize the information concerning the presence of the expansion module and the expansion module type for each slot of the stack. The information is coded as follow: First Octet: number of slots Second Octet: SNMP Type of information: Integer=2, OctetString=4 Third Octet: Length of each field Last Octets: For each slot, if no expansion module is present, the value will be 0; otherwise, the plug-in-type-number (written in number of octets described in the 3rd octet) | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| chLogFileTable | 1.3.6.1.4.1.81.7.22 | ||
| Table describing all the reset occurrences in a switch, doubly indexed by the group number and the sequential number of the reset event | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ChLogFileEntry | |||
| chLogFileEntry | 1.3.6.1.4.1.81.7.22.1 | ||
| An entry in the table, containing data on a single reset event that occurred to a single group. | |||
| OBJECT-TYPE | |||
| ChLogFileEntry | |||
| chLogFileGroupId | 1.3.6.1.4.1.81.7.22.1.1 | ||
| Index which identifies the group or slot number. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| chLogFileIndex | 1.3.6.1.4.1.81.7.22.1.2 | ||
| Index which identifies the sequential number of a reset event. Index #1 always represents the last recent reset event that occurred. Every new reset event causes a shift in the table entries. When the maximum storage capacity of the switch is reached, the oldest entry is shifted out of the table (FIFO) | |||
| OBJECT-TYPE | |||
| INTEGER | 1..65535 | ||
| chLogFileName | 1.3.6.1.4.1.81.7.22.1.3 | ||
| An enumeration which identifies the type of the log file we fetch. | |||
| OBJECT-TYPE | |||
| INTEGER | reset(1), other(255) | ||
| chLogFileAbsoluteTime | 1.3.6.1.4.1.81.7.22.1.4 | ||
| Absolute time in seconds at which the reset occurred. The absolute time is retrieved by the Agent from the net, in a standard format. In the case where the reset occurred before the Agent was already able to retrieve the absolute time, it should indicate 0. | |||
| OBJECT-TYPE | |||
| Counter | |||
| chLogFileMessage | 1.3.6.1.4.1.81.7.22.1.5 | ||
| Readable text message, which will contain a full description of the reset event and its cause. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..600) | ||
| chLogFileEncryptedMessage | 1.3.6.1.4.1.81.7.22.1.6 | ||
| Encrypted message saved in the Flash memory, which will contain a full description of the reset event, that is understandable to the Technician only. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..600) | ||
| chLicenseKey | 1.3.6.1.4.1.81.7.23 | ||
| This MIB item contains the authorization key for SMON application, and for other applications in the future. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(12) | ||
| genGroup | 1.3.6.1.4.1.81.8 | ||
| OBJECT IDENTIFIER | |||
| genGroupTable | 1.3.6.1.4.1.81.8.1 | ||
| Table of configuration attributes for managed modules. Includes configuration data which are independent of the specific functionality of the module. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| GenGroupEntry | |||
| genGroupEntry | 1.3.6.1.4.1.81.8.1.1 | ||
| An entry in the table, containing data about a single group. | |||
| OBJECT-TYPE | |||
| GenGroupEntry | |||
| genGroupId | 1.3.6.1.4.1.81.8.1.1.1 | ||
| Index which identifies the group inside the chassis for which this entry contains information. Equals the number of the slot by which the group is accessed. This value is never greater than chNumberOfSlots. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| genGroupSWVersion | 1.3.6.1.4.1.81.8.1.1.2 | ||
| ASCII string for description and display of the group software version. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| genGroupKernelVersion | 1.3.6.1.4.1.81.8.1.1.3 | ||
| ASCII string for description and display of the group kernel version. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| genGroupType | 1.3.6.1.4.1.81.8.1.1.4 | ||
| Attribute describing the type of the group (module). | |||
| OBJECT-TYPE | |||
| INTEGER | le10b(1), le10b-2(2), le10c(3), le10c-2(4), le15(5), le15-2(6), le20(7), le30x(8), le30x-2(9), le30xd(10), le40x(11), le40xt(12), ltr4-RJ45(13), ltr4-D9(14), ltr4-D25(15), ltr4-FO(16), ltrio-RJ45(19), ltrio-D9(20), ltrio-D25(21), ltrio-FO(22), ltrio-Con1(23), ltrio-Con2(24), le10b-2r(25), le10c-2r(26), le80xt(27), le140xt(28), ielb(29), ltrf4(30), ltrf16(31), lts16(32), le20n(33), ltr104-RJ45(34), le20r(35), llt8(36), le20s(37), le10b2n(38), ltr104-D9(39), ltr104-D25(40), ltrt-RJ45(41), ltrt-D9(42), ltr104f(43), itlb(44), le140xtf(45), le120r(46), le120r-2(47), le140xtc(48), le110b(49), le110bq(50), lcl100(51), le140xtq(52), le20n-fb(53), le20s-fb(54), le140xtf-fb(55), ltr104s(56), lert40-AUI(57), lert40-10BASET(58), lfd104-mic(59), lfd104-stm(60), lfd104-stl(61), lfd104-stp(62), lfd104-utp(63), lfd102-mic(64), lfd102-stm(65), lfd102-sts(66), le140xtn(67), ltr104a(68), le120q(69), le120sq2(70), le120sq5(71), le120q-fb(72), le120sq2-fb(73), le120sq5-fb(74), ltr108t(75), ltr108f(76), lse808(77), lhs(78), iefn(80), itfn(81), ierp(86), lse108(87), lse208(88), le110cq(89), itre2(90), sh-e16(92), le115q(93), sh-t16(94), sh-e8(95), lhb(96), sh-efn(97), sh-tfn(98), lace100(100), le140xts(101), le40xtn(102), le80xtn(103), itrp(104), lfd104-lcf(105), lfd104-sts(106), lfd102-lcf(107), lfd102-stl(108), lfd102-stp(109), lfd102-utp(110), phy4-mic(111), phy4-stm(112), phy4-stl(113), phy4-stp(114), phy4-utp(115), phy4-lcf(116), phy4-sts(117), phy2-mic(118), phy2-stm(119), phy2-stl(120), phy2-stp(121), phy2-utp(122), phy2-lcf(123), phy2-sts(124), sh-t16io-c(126), sh-t16io-fr(127), lse404(128), sh-t16io-cr(129), sh-e8fb(131), sh-e8fl(132), iefr-mc(134), ieqr(136), iere2(138), ltr104sn(139), le240xtc(140), le280xt(141), sh-e16fb(143), sh-e16fl(144), lse404s(145), lse404s-fb(146), lse404srj(147), le240xtcs(148), le280xts(149), lsa(150), lfe100n(151), lsf100(152), lfe100(153), lst168(154), lea10BT(155), lea10BTRed(156), leaFl(157), leaFlRed(158), sh-e24(159), sh-e24s(160), lfe1008(161), le180xt(163), sh-e24fl(164), sh-e24fb(165), sh-e24sfl(166), sh-e24sfb(167), sh-40sf(168), sh-80rj(169), lse-pm(170), lsf100n(171), ls3ls(172), las(173), leb200n(174), leb200(175), fat-pipe-fddi(176), lfe4004(178), lbt155(185), lsa2(186), lbt155Plus(187), lfe4004ST(188), lfe4004SF(189), lge-2000SX(190), lge-2000LX(191), lfe8008S(192), visage24T(1000), visage16200F(1001), visage16200T(1004), visage16200FC(1005), visage800T(1006), visage800F(1007), visage16155FR(1008), visage16155F(1009), visage2500(1010), visage3LS(1012), visage1600T(1013), visage2008SX(1014), visage2008LX(1015), visage1008SX(1016), visage1008LX(1017), visage26Plus(1025), visage26PlusFxMM(1026), visage26PlusFxSM(1027), visage26PlusTx(1028), cajunP117S(1029), cajunP117SR(1030), m12-100T(2000), m12-100F(2001), m-spv(2002), nma-rs(2003), nma-re(2004), m-spx(2005), m2-1000SX(2006), m2-1000LX(2007), m14-10F(2008), m24-10T(2009), m-sps-T(2010), m-sps-ER(2011), m-sps-EB(2012), m32-100T(2013), m-accf(2014), m-accsf(2015), m-mls(2200), cajunP120(2500), cajunP333T(2501), cajunP333R(2502), cajunP122(2503), cajunP334T(2504), cajunP332MF(2505), cajunP133G2(2506), cajunP332G-ML(2507), cajunP133F2(2508), cajunP134G2(2509), cajunP332GT-ML(2510), cajunP334T-ML(2511), cajunP333RLB(2512), cajunP333T-PWR(2513), c-Hawk(2800), m15-155F(3000), m3-622F(3001), m3-622SF(3002), m15-155SF(3003), m15-155MS(3004), m2-2400I(3005), m4-DS3(3009), m4-E3(3010), unknown(255) | ||
| genGroupDescr | 1.3.6.1.4.1.81.8.1.1.5 | ||
| Descriptor of the group in ASCII (readable) format, mainly for use with generic management applications. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..32) | ||
| genGroupNumberOfPorts | 1.3.6.1.4.1.81.8.1.1.6 | ||
| Number of ports in group. It is assumed that on each group the ports are assigned unique numbers in the range from 1 to genGroupNumberOfPorts. They correspond to the number of ports on the module (FRU) | |||
| OBJECT-TYPE | |||
| INTEGER | 0..255 | ||
| genGroupNumberOfIntPorts | 1.3.6.1.4.1.81.8.1.1.7 | ||
| Number of internal ports (ports connected to the chassis buses) on the module. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..255 | ||
| genGroupReset | 1.3.6.1.4.1.81.8.1.1.8 | ||
| Setting the value of this attribute to 'on' is interpreted as a software RESET command. Sensor software is reinitialized and according to the sensor specifications, partial or total reset of the module hardware may be performed. | |||
| OBJECT-TYPE | |||
| INTEGER | on(1), off(2), notSupported(255) | ||
| genGroupAutoMan | 1.3.6.1.4.1.81.8.1.1.9 | ||
| This attribute reflects the status of the Auto/Manual switch which defines the working mode of sensors. In the MANUAL mode no set operations may be performed on attributes related to the sensor. The sensor works according to configuration switches set by hardware and transmits all configuration information to the agent. In the AUTO mode, hardware switches are overridden by set commands. | |||
| OBJECT-TYPE | |||
| INTEGER | auto(1), man(2) | ||
| genGroupFullConfig | 1.3.6.1.4.1.81.8.1.1.10 | ||
| Attribute describing the full configuration of a group in internal application format. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| genGroupRedun12 | 1.3.6.1.4.1.81.8.1.1.11 | ||
| Value on(1) of this attribute defines a redundancy (backup) relationship between synchronous external ports 1 and 2 on a module. Value blocked(3) of this attribute defines that the module is in the redundancy block mode used by IMR based modules. | |||
| OBJECT-TYPE | |||
| INTEGER | on(1), off(2), blocked(3), notSupported(255) | ||
| genGroupRedun34 | 1.3.6.1.4.1.81.8.1.1.12 | ||
| Value ON of this attribute defines a redundancy (backup) relationship between synchronous external ports 3 and 4 on a module. | |||
| OBJECT-TYPE | |||
| INTEGER | on(1), off(2), notSupported(255) | ||
| genGroupRedun13-14 | 1.3.6.1.4.1.81.8.1.1.13 | ||
| Value ON of this attribute defines a redundancy (backup) relationship between synchronous external ports 13 and 14 on a module. | |||
| OBJECT-TYPE | |||
| INTEGER | on(1), off(2), notSupported(255) | ||
| genGroupStandAloneMode | 1.3.6.1.4.1.81.8.1.1.14 | ||
| Value ON of this attribute indicates the sensor's operation Stand Alone mode . Internal ports are disabled and the card functions in a local star configuration toward its external ports. | |||
| OBJECT-TYPE | |||
| INTEGER | on(1), off(2), notSupported(255) | ||
| genGroupInterProcCommStatus | 1.3.6.1.4.1.81.8.1.1.15 | ||
| This attribute describes the status of the communication between the microprocessor of the sensor and the microprocessor of the agent on cards with embedded agents. | |||
| OBJECT-TYPE | |||
| INTEGER | ok(1), commProblems(2), noCommunication(3), notSupported(255) | ||
| genGroupCommStatus | 1.3.6.1.4.1.81.8.1.1.16 | ||
| This attribute describes the communication status of the group with the SNMP Agent as detected and reported by the agent. | |||
| OBJECT-TYPE | |||
| INTEGER | ok(1), commProblems(2), noCommunication(3), notSupported(255) | ||
| genGroupHWStatus | 1.3.6.1.4.1.81.8.1.1.17 | ||
| This attribute describes the status of the group hardware as detected by the sensors software. | |||
| OBJECT-TYPE | |||
| INTEGER | ok(1), hardwareProblems(2), notSupported(255) | ||
| genGroupSupplyVoltageFault | 1.3.6.1.4.1.81.8.1.1.18 | ||
| A value 'on' of this attribute informs of a 'voltage supply out-of-range' error condition on sensor equipped with hardware which checks this condition. | |||
| OBJECT-TYPE | |||
| INTEGER | on(1), off(2), notSupported(255) | ||
| genGroupIntTemp | 1.3.6.1.4.1.81.8.1.1.19 | ||
| Internal temperature of the enclosure as measured by the specific module instance.Value '999' means not supported. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| genGroupSpecificOID | 1.3.6.1.4.1.81.8.1.1.20 | ||
| This attribute provides the OID of another group containing additional more specific information regarding this instance. | |||
| OBJECT-TYPE | |||
| OBJECT IDENTIFIER | |||
| genGroupConfigurationSymbol | 1.3.6.1.4.1.81.8.1.1.21 | ||
| Defines the Configuration Symbol attached to any hardware module manufactured. One single character A..Z defines the CS version. For older modules which did not support this option on SNMP character '*' will be returned. Meritage modules will use a new format X.Y - where X & Y are integers: 1st byte (X) - Major version number 2nd byte - '.' 3rd byte (Y) - minor version number | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| genGroupLastChange | 1.3.6.1.4.1.81.8.1.1.22 | ||
| This attribute contains the value of sysUpTime at the time any change pertaining to the specified group occurred. | |||
| OBJECT-TYPE | |||
| TimeTicks | |||
| genGroupRedunRecovery | 1.3.6.1.4.1.81.8.1.1.23 | ||
| This attribute is relevant for the cards with redundancy feature (LTR-108F). It defines the behaviour in case of main port failure: on(1) - the data path returns to the main port when its correct functionality is recovered. off(2) - the data path stays with the redundant port. | |||
| OBJECT-TYPE | |||
| INTEGER | on(1), off(2), notSupported(255) | ||
| genGroupHWVersion | 1.3.6.1.4.1.81.8.1.1.24 | ||
| Defines the Hardware version of the module. Current modules use a single character A - D. Very old modules which do not support this mib will be returned an asterisk '*' | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| genGroupHeight | 1.3.6.1.4.1.81.8.1.1.25 | ||
| This item describes the physical height of the module in Us (1U=1.75''). | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| genGroupWidth | 1.3.6.1.4.1.81.8.1.1.26 | ||
| This item describes the physical width of the module in HP units (1HP=0.5 mm). | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| genGroupIntrusionControl | 1.3.6.1.4.1.81.8.1.1.27 | ||
| Group intrusion security mode (not supported or Security Bypass or Secure) assigned to this module. Security Bypass - all ports in this group are not secure. Secure - ports in this group will perform security as defined per port, in the port level. The information is coded in internal format. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| genGroupThresholdStatus | 1.3.6.1.4.1.81.8.1.1.28 | ||
| This item is a bitmap that defines the threshold status of the module, in relation to the alarmPolicyTable. If the ring is monitored by the agent according to policy number x in the alarmPolicyTable, and the threshold condition has occured, then the bit #x in this item will have the value '1'. Otherwise it will be '0'. For x-186 based agents all bits of this item are '0'. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(4) | ||
| genGroupEavesdropping | 1.3.6.1.4.1.81.8.1.1.29 | ||
| Group eavesdropping security mode (not supported or Security Bypass or Secure) assigned to this module. Security Bypass - all ports in this group are not secure. Secure - ports in this group will perform security as defined per port, in the port level. This attribute can be assigned to security modules. The information is coded in internal proprierty format. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| genGroupMainSWVersion | 1.3.6.1.4.1.81.8.1.1.30 | ||
| ASCII string for description and display of the main CPU software version in modules that utilize more than one management processor. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| genGroupMPSActivityStatus | 1.3.6.1.4.1.81.8.1.1.31 | ||
| This attribute defines the status of the main PS inside the stackable hub. | |||
| OBJECT-TYPE | |||
| INTEGER | notActive(1), active(2), notSupported(255) | ||
| genGroupBUPSActivityStatus | 1.3.6.1.4.1.81.8.1.1.32 | ||
| This attribute defines the status of the backup PS externally connected to the module. | |||
| OBJECT-TYPE | |||
| INTEGER | notActive(1), active(2), notPresent(3), notSupported(255) | ||
| genGroupPrepareCounters | 1.3.6.1.4.1.81.8.1.1.33 | ||
| This item should help the agent to prepare a large amount of counters. The agent should reset this value to none(1), when it has terminated to prepare the counters. fethGroupCounters(7) - This counters are only supported by RISC agents for LFE1008. | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), ethPortCounters(2), ethPortErrCounters(3), ethPortSWCounters(4), fethPortSWCounters(5), ethGroupCounters(6), fethGroupCounters(7), scEthCounters(8), notSupported(255) | ||
| genGroupPortLastChange | 1.3.6.1.4.1.81.8.1.1.34 | ||
| This item contains the last two bytes of the TimeStamp of the last change of each port as follows: Bytes 0 -1: port 1, Bytes 2 -3: port 2, Bytes 4 -5: port 3, and so on. No trap should be sent on the item change. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| genGroupIntPortLastChange | 1.3.6.1.4.1.81.8.1.1.35 | ||
| This item contains the last two bytes of the TimeStamp of the last change of each internal port as follows: Bytes 0 -1: internal port 1, Bytes 2 -3: internal port 2, Bytes 4 -5: internal port 3, and so on. No trap should be sent on the item change. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| genGroupFaultMask | 1.3.6.1.4.1.81.8.1.1.36 | ||
| Each bit of this item describes the situation of the group regarding specific fault. For example: bit 1: on indicates 'module internal communication problem' bit 2 : on indicates 'module hardware problem' and so on. The fault traps will be sent. 1 genGroupInterProcCommStatus =commProblems(2) or genGroupInterProcCommStatus =noCommunication(3), or genGroupCommStatus = commProblems(2) or genGroupCommStatus = noCommunication(3) 2 genGroupSupplyVoltageFault = on(1) or genGroupHWStatus = hardwareProblems(2) or fethGroupFunctionalStatus = malfunctioning(3) 3 ethGroupFIFO = on(1) 4 ethGroupWrongPortSelection = on(1) 5 radFddiGroupTestResult= faulty(2) 6 iwrPMState = fail(2) or iwrIOMState = fail(2) 7 genGroupMPSActivityStatus = notActive(1) 8 genGroupBUPSActivityStatus = notActive(1) 9 lntAtmGroupBITResult = faulty(2) 10 tokGroupLSTBeaconing = on(1) 11 genCTIGroupCellLossAlarm=cellLossAlarm(2) 12 scGenGroupStatus=loadsBudgetProblem(2) 13 scGenGroupFansStatus=oneFanFailed(2) 14 scGenGroupBUPSFansStatus=oneFanFailed(2) 15 genGroupCascadUpStatus=rld(2) 16 genGroupCascadDownStatus=rld(2) 17 genGroupCascadUpStatus=blocked(3) 18 genGroupCascadDownStatus=blocked(3) | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| genGroupTypeName | 1.3.6.1.4.1.81.8.1.1.37 | ||
| String with the module name. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..32) | ||
| genGroupAgentSlot | 1.3.6.1.4.1.81.8.1.1.38 | ||
| This attribute defines the slot number of the Agent supporting this group. If there is multiplexor, than the value will be the multiplxor slot number. If there is no multiplexor, the value will be the mudule's slot number. The default value is the module's slot number. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| genGroupMngType | 1.3.6.1.4.1.81.8.1.1.39 | ||
| This attribute defines the management type of the module. | |||
| OBJECT-TYPE | |||
| INTEGER | agent(1), subAgent(2), sensor(3), notSupported(255) | ||
| genGroupNumberOfLogicalPorts | 1.3.6.1.4.1.81.8.1.1.40 | ||
| Number of logical ports in group. The logical ports represent the Link Aggregation Groups (LAGs) associated with that module/switch. It is assumed that on each group the logical ports are assigned unique numbers in the range from (genGroupNumberOfPorts+1) to (genGroupNumberOfPorts+genGroupNumberOf LogicalPorts). | |||
| OBJECT-TYPE | |||
| INTEGER | 0..255 | ||
| genGroupNumberOfInterfaces | 1.3.6.1.4.1.81.8.1.1.41 | ||
| The number of network interfaces (regardless of their current state) present on this module. This will help determined the ifNumber for the entire system | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| genGroupCascadUpStatus | 1.3.6.1.4.1.81.8.1.1.42 | ||
| The functional status of the P330 two cascading-up ports: ok(1) - fully functional ports, transmitting and receiving packets. rld(2) - receive link down condition on at least one of the ports. blocked(3) - stacking up problem | |||
| OBJECT-TYPE | |||
| INTEGER | ok(1), rld(2), blocked(3), notSupported(255) | ||
| genGroupCascadDownStatus | 1.3.6.1.4.1.81.8.1.1.43 | ||
| The functional status of the P330 two cascading-down ports: ok(1) - fully functional ports, transmitting and receiving packets. rld(2) - receive link down condition on at least one of the ports. blocked(3) - stacking down problem | |||
| OBJECT-TYPE | |||
| INTEGER | ok(1), rld(2), blocked(3), notSupported(255) | ||
| genGroupSTARootPortID | 1.3.6.1.4.1.81.8.1.1.44 | ||
| The port ID. Number through which the STA Root bridge can be reached. If it is one of the P330 backplane port, its port id. will be from 201 to 204, as referring to backplane Guitar ports, numbered from 0 to 3 respectively. This will help the STA to run in a distributed environment, i.e. as for P330. Note that internally, STA function will use only one port id. for the backplane ports, that is 120. For this reason, port id. 120 should not be used in the future. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| genGroupCopyPortInstruction | 1.3.6.1.4.1.81.8.1.1.45 | ||
| This variable is used internally by the P330 Master for sending a contracted instruction code to every Slave agent of the stack. The instruction is coded as follows: 1st Octet: 0 - reset the following port mirroring 1 - set the following port mirroring 2nd to 5th: mirroring source port id. 6th to 9th: mirroring destination port id. 10th Octet: mirroring direction: 1 - Rx only 2 - Tx only 3 - both Ports id. 201 to 204 refer to the P330 backplane Guitar ports, 0 to 3 respectively. Port id. 301, 302, 303 refer to P330 backplane LAGs, down, up, and fat (a single four ports LAG) respectively. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| genGroupLicenseKey | 1.3.6.1.4.1.81.8.1.1.46 | ||
| This MIB item contains the authorization key for SMON application, and for other applications in the future. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(12) | ||
| genGroupLogFileClear | 1.3.6.1.4.1.81.8.1.1.47 | ||
| This attribute enables the user to clear all the log files attached of a specific module. | |||
| OBJECT-TYPE | |||
| INTEGER | on(1), off(2) | ||
| genGroupBootVersion | 1.3.6.1.4.1.81.8.1.1.48 | ||
| ASCII string for description and display of the booter version of the module. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| genGroupResetLastStamp | 1.3.6.1.4.1.81.8.1.1.49 | ||
| This attribute contains the value of sysUpTime at the time it polled | |||
| OBJECT-TYPE | |||
| TimeTicks | |||
| genGroupSerialNumber | 1.3.6.1.4.1.81.8.1.1.50 | ||
| The burnt-in identifier of the device. This is a unique 7-digits number | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| genGroupShowModuleInformation | 1.3.6.1.4.1.81.8.1.1.51 | ||
| String that includes all information of the Show Module CLI Command. TAB String indicates new column, while CR String indicates new line. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| genGroupCascadingUpFault | 1.3.6.1.4.1.81.8.1.1.52 | ||
| Enable /Disable the sending of cascading up fault traps for this module. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2), notSupported(255) | ||
| genGroupCascadingDownFault | 1.3.6.1.4.1.81.8.1.1.53 | ||
| Enable /Disable the sending of cascading down fault traps for this module. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2), notSupported(255) | ||
| genGroupPortClassificationMask | 1.3.6.1.4.1.81.8.1.1.54 | ||
| This is a mask of the port classification values of all ports of this module. The index of the bits starts from 0, where bit 0 is unused. If the n bit has value of 1 - it means that the n port has valuable port classification. If the value of the n bit is 0 then either there is no such port or its port classification is 0. For example: If the first 10 ports of a module are valuable ports and there is no plugin then the value of this MIB is: 7f e0 If a module has 10 regular ports and there is a plugin with 2 valuable ports (which are considered as ports 51, 52) then the value of this MIB is: 00 00 00 00 00 00 18 | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| genPort | 1.3.6.1.4.1.81.9 | ||
| OBJECT IDENTIFIER | |||
| genPortTable | 1.3.6.1.4.1.81.9.1 | ||
| Table of configuration attributes for managed ports. Includes configuration data which are independent of the specific functionality of the port. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| GenPortEntry | |||
| genPortEntry | 1.3.6.1.4.1.81.9.1.1 | ||
| An entry in the table, containing data about a single port. | |||
| OBJECT-TYPE | |||
| GenPortEntry | |||
| genPortGroupId | 1.3.6.1.4.1.81.9.1.1.1 | ||
| Index which identifies the group inside the chassis for which this entry contains information. Equals the number of the slot by which the group containing the port is accessed. This value is never greater than chNumberOfSlots. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| genPortId | 1.3.6.1.4.1.81.9.1.1.2 | ||
| Index which identifies the port inside the group for which this entry contains information. It generally corresponds with the number by which the port is identified and is marked on the module. This value is never greater than genGroupNumberOfPorts of the group to which the port belongs. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| genPortFunctionality | 1.3.6.1.4.1.81.9.1.1.3 | ||
| Describes the functionality of the port according to international standards. | |||
| OBJECT-TYPE | |||
| INTEGER | private(1), repeaterAUI(2), repeaterThin(3), repeater10BaseT(4), tenBaseFSyncAct(5), foirl(6), xcvr(7), lobe(8), ri(9), ro(10), serial(11), localTalk(12), fddi(13), clock(14), genTokenRing(15), dte(16), activeLobe(17), genActiveTokenRing(18), tenBaseFB(19), eth10BaseT(20), fiber(21), wan(22), star(23), activeRI(24), activeRO(25), fl(26), sonet-oc3(27), a100BaseTX(28), a100BaseFX(29), oc3(30), anATM-Main(31), anATM-Secondary(32), a1000BaseFX(33), sonet(40), fimVoice(41), sdh-stm1(42), eth1000BaseSX(43), eth1000BaseLX(44), eth10BaseFL(45), ethLAG(46), lag100(47), lag1000(48), eth1000BaseTX(49), eth1000BaseCX(50), gBICNotPresent(51), gBICNotSupported(52), eth1000BaseX-Proprietary(53), oc12(54), sFP-NotPresent(55), sFP-NotSupported(56), eth10BaseTwInPWR(57), eth100BaseTXwInPWR(58) | ||
| genPortType | 1.3.6.1.4.1.81.9.1.1.4 | ||
| Attribute describing the type of port. | |||
| OBJECT-TYPE | |||
| INTEGER | le10bPort(1), le10cPort(2), le15Port(3), le20Port(4), le30xPort(5), le30xdPort(6), le40xPort(7), le40xtPort(8), lobeRJ45(9), lobeD9(10), lobeD25(11), lobeFO(12), ri104D25(13), ro104D25(14), riRJ45(15), riD9(16), riD25(17), riFO(18), ri104RJ45(19), ri104D9(20), roRJ45(21), roD9(22), roD25(23), roFO(24), ro104RJ45(25), ro104D9(26), le80xtPort(27), le140xtPort(28), ielb-AUIPort(29), ielb-10btPort(30), ltrf4Port(31), ltrf16Port(32), lts16Port(33), llt8Port(34), le20rPort(35), itlbRoPort(36), itlbRiPort(37), itlbDTEPort(38), starFO(39), le10bnPort(40), le120rPort(41), le140xtf-foPort(42), le140xtf-10btPort(43), le140xtcPort(44), le110bPort(45), le110bqPort(46), le140xtqPort(47), lert40-AUIPort(48), lert40-10btPort(49), clock-int(50), clock-ext(51), ri104RJ45S(52), ro104RJ45S(53), lobe104RJ45S(54), le20fbPort(55), le140xtf-fofbPort(56), fddi-micPort1(57), fddi-micPort2(58), fddi-micPort3(59), fddi-stmPort1(60), fddi-stmPort2(61), fddi-stmPort3(62), fddi-stlPort1(63), fddi-stlPort2(64), fddi-stlPort3(65), fddi-stpPort1(66), fddi-stpPort2(67), fddi-stpPort3(68), fddi-utpPort1(69), fddi-utpPort2(70), fddi-utpPort3(71), fddi-stsPort1(72), fddi-stsPort2(73), fddi-stsPort3(74), le140xtnPort(75), ltr104a-lobePort(76), ltr104a-riPort(77), ltr104a-roPort(78), le120qPort(79), le120sq2PortS(80), le120sq2PortM(81), le120sq5Port(82), le120q-fbPort(83), le120sq2-fbPortS(84), le120sq2-fbPortM(85), le120sq5-fbPort(86), ltr108t-lobePort1(87), ltr108t-riPort1(88), ltr108t-roPort1(89), ltr108t-lobePort(90), ltr108f-lobePort(91), ltr108f-starPortFO(92), ltr108f-riPortFO(93), ltr108f-roPortFO(94), lse808Port(95), lhsPort(96), iefnPort(98), itfnPort(99), itrePort(100), ierpPort(107), lse108Port(108), lse208Port(109), le110cqPort(110), ltr108t-starPort1(111), she-10btPort(112), she-AUIPort(113), she-FOPort(114), she-FOSyncPort(115), le115qPort(116), sht-lobePort(117), sht-riRJ45Port(118), sht-riD9Port(119), sht-riFOPort(120), sht-roRJ45Port(121), sht-roD9Port(122), sht-roFOPort(123), lhbPort(124), le140xtsPort(126), le40xtnPort(127), le80xtnPort(128), itrpPort(129), fddi-lcfPort1(130), fddi-lcfPort2(131), fddi-lcfPort3(132), ltr108f-lobeRJ45(133), lse404Port(134), star104RJ45S(135), she-10bfbPort(136), sht-starPort(137), le240xtcPort(138), le280xtPort(139), iefrMICPort(140), ri104RJ45SN(141), iwr10BaseTPort(142), ro104RJ45SN(144), sh-efn-AUIPort(145), lobe104RJ45SN(146), sh-efnPort(147), sh-tfnPort(148), ierePort(152), lse404sPort(153), lse404s-fbPort(154), le240xtcsPort(155), le280xtsPort(156), atmMMFPort(157), lsaPort(158), atmUTPPort(159), sh-elbAUIPort(160), sh-elb10btPort(161), lse404srjPort(162), lfe100Port(163), lsf100Port(164), lst-lobeRJ45Port(165), lst-starRJ45Port(166), lst-riRJ45Port(167), lst-roRJ45Port(168), tenBaseTPort(169), flPort(170), shes-10btPort(171), shes-AUIPort(172), shes-FOPort(173), shes-10bfbPort(174), le180xtPort(175), lfe1008Port(177), lse-pmPort(178), sh-40sfPort(179), sh-80rjPort(180), ls3ls-WAN(181), leb200Port(183), fat-pipe-fddiPort(184), lfe4004Port(186), sonetPort(190), fimVoicePort(191), lfe4004SFPort(192), lfe4004STPort(193), lge-2000SXPort(194), lge-2000LXPort(195), lfe8008SUTPPort(196), visage10BTPort(1000), visage16200FPort(1001), visage16200TPort(1004), visage16200FCPort(1005), visage800TPort(1006), visage800FPort(1007), visage16155FRPort(1008), visage16155FPort(1009), visage2500Port(1010), visage3LSPort(1012), visage1600TPort(1013), visage1000BaseSXPort(1014), visage1000BaseLXPort(1015), cajunP117SPort(1016), cajunP117SRPort(1017), m10or100BaseTXPort(2000), m100BaseFXPort(2001), m1000BaseSXPort(2002), m1000BaseLXPort(2003), m10BaseFLPort(2004), m10BaseTPort(2005), m10or100BaseTXdot1QPort(2006), m-acc155or622MMFPort(2007), m-acc155or622SMFPort(2008), cajunP120-10or100TPort(2500), cajunP120-100FPort(2501), cajunP120-1000SXPort(2502), cajunP120-1000LXPort(2503), cajunP330-10or100TPort(2504), cajunP330-100FPort(2505), cajunP330-1000SXPort(2506), cajunP330-1000LXPort(2507), cajunP330-LAG(2508), cajunP330-LAG100(2509), cajunP330-LAG1000(2510), cajunP110-LAG100(2511), cajunP110-LAG1000(2512), cajunP120-1000BaseCX-GBIC(2513), cajunP120-1000BaseSX-GBIC(2514), cajunP120-1000BaseLX-GBIC(2515), cajunP120-1000BaseT-GBIC(2516), cajunP120-GBIC-NotPresent(2517), cajunP120-GBIC-Unknown(2518), cajunP120-GBIC-Other(2519), cajunP120-FibreChannel-GBIC(2520), cajunP120-1000BaseTX(2521), cajunP330-1000TXPort(2522), cajunP330-1000SX-GBIC(2523), cajunP330-1000LX-GBIC(2524), cajunP330-1000T-GBIC(2525), cajunP330-1000CX-GBIC(2526), cajunP330-GBIC-NotPresent(2527), cajunP330-GBIC-NotSupported(2528), cajunP130-10or100BaseTXPort(2530), cajunP130-100BaseFXPort(2531), cajunP130-1000BaseSX-GBICPort(2532), cajunP130-1000BaseLX-GBICPort(2533), cajunP130-1000BaseX-Proprietary-GBICPort(2534), cajunP130-GBIC-NotSupported(2535), cajunP130-GBIC-NotPresent(2536), cajunP130-LAG100(2537), cajunP130-LAG1000(2538), cajunP130-1000BaseTPort(2539), cajunP330-ML-LAG(2540), cajunP330-ML-1000SX-SFP(2541), cajunP330-ML-1000LX-SFP(2542), cajunP330-ML-LAG100(2543), cajunP330-ML-LAG1000(2544), cajunP330-ML-100or1000TPort(2545), cajunP330-ML-10or100TPort(2546), cajunP330-ML-SFP-NotPresent(2547), cajunP330-ML-SFP-NotSupported(2548), cajunP330-10or100TPortAndInPWR(2549), m15-155FPort(3000), m3-622FPort(3001), m3-622SFPort(3002), m15-155SFPort(3003), m15-155MSPort(3004), m2-2400IPort(3005), m4-DS3Port(3009), m4-E3Port(3010), unknownPort(255) | ||
| genPortDescr | 1.3.6.1.4.1.81.9.1.1.5 | ||
| Descriptor of the port in ASCII (readable) format, mainly for use with generic management applications. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..32) | ||
| genPortActivityStatus | 1.3.6.1.4.1.81.9.1.1.6 | ||
| This attribute defines the status of ports that may be part of a redundancy scheme. notActive(1) - indicates a disabled port which cannot transmit or receive packets even if included in a redundancy scheme. dormant(2) - indicates an enabled port which does not transmit or receive packets, but because it is included in a redundancy scheme, it may at any moment become responsible packet transmission and reception. active(3) - indicates that the port transmits and receives packets, serving as the main path in the redundant configuration. | |||
| OBJECT-TYPE | |||
| INTEGER | notActive(1), dormant(2), active(3), notSupported(255) | ||
| genPortSecurityPolicy | 1.3.6.1.4.1.81.9.1.1.7 | ||
| Security policy (noPolicy or Trap Only or Trap and Close) assigned to this port. noPolicy - do not perform intrusion control security mechanism. Trap Only - perform intrusion control security mechanism and trap the console, in case of security violation. Trap and Close - perform intrusion control security mechanism, trap the console and close this port, in case of security violation. The information is coded in internal format. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| genPortSecureAddresses | 1.3.6.1.4.1.81.9.1.1.8 | ||
| This attribute defines the security information (physical addresses) relevant for the entry. Coded in internal format, cryptographic methods may be used for privacy purposes. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| genPortIntPortConnection | 1.3.6.1.4.1.81.9.1.1.9 | ||
| The value of this attribute defines the internal port to which the port is connected. A value 0 of this attribute would indicate no internal port connection (stand-alone mode). Any other positive value equals the number of the internal port. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..255 | ||
| genPortAdminStatus | 1.3.6.1.4.1.81.9.1.1.10 | ||
| A disabled port neither transmits nor receives. The port must be explicitly enabled to restore operation. For token ring ports, this attribute is read-only. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| genPortSpecificOID | 1.3.6.1.4.1.81.9.1.1.11 | ||
| This attribute provides the OID of another group containing additional more specific information regarding this instance. | |||
| OBJECT-TYPE | |||
| OBJECT IDENTIFIER | |||
| genPortThresholdStatus | 1.3.6.1.4.1.81.9.1.1.12 | ||
| This item is a bitmap that defines the threshold status of the port, in relation to the alarmPolicyTable. If the port is monitored by the agent according to policy number x in the alarmPolicyTable, and the threshold condition has occurred, then the bit #x in this item will have the value '1'. Otherwise it will be '0'. For x-186 based agents all bits of this item are '0'. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(4) | ||
| genPortEavesdropping | 1.3.6.1.4.1.81.9.1.1.13 | ||
| Eavesdropping security mechanism (Off or On) assigned to this port. On - perform Eavesdropping security mechanism in the port. The information is coded in internal format. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| genPortFaultMask | 1.3.6.1.4.1.81.9.1.1.14 | ||
| Each bit of this item describes the situation of the port regarding specific fault. For example: bit 1: on indicates 'port autopartition fault' bit4 : on indicates 'Ethernet port connection problem' and so on. The fault trap will be sent contains the genPortFaultMask item. 0 Don't care 1 ethPortAutoPartitionState = autoPartition(1) or fethPortAutoPartitionState = autoPartition(1) or scEthPortFunctionalStatus = partition(8) or genPortFunctionalStatus = partition(8) 4 ethPortNoAUILoop = on(1) or ethPortJabber = on(1) or ethPortMJLP = on(1) or ethPortFunctionalStatus = localJabber(3) or ethPortFunctionalStatus = illSeq(6) or ethPortFunctionalStatus = shortCirc(7) or ethPortFunctionalStatus = partitionOrLocalJabber(8) or ethPortFIFO = on(1) or fethPortFIFO = on(1) or fethPortFunctionalStatus = localJabber(3) or scEthPortAutoNegotiationStatus = fail(2) 7 ethPortFunctionalStatus = rld(2) or fethPortFunctionalStatus = rld(2) or scEthPortFunctionalStatus = rld(2) or genPortFunctionalStatus = rld(2) 10 ethPortFunctionalStatus = tld(4) or ethPortFunctionalStatus = remoteJabber(5) or ethPortFunctionalStatus = remoteFaultOrLockLost(9) or ethPortFunctionalStatus = remoteFault(10) or ethPortFunctionalStatus = lockLost(11) or fethPortFunctionalStatus = remoteFault(10) 11 tokPortRingSpeedError= on(1) 12 tokPortFunctionalStatus = rld(2) or tld(4) or tokPortConnected = notConnected(2) 15 tokPortCableFault = on(1) 16 radFddiPortTestResult= faulty(2) 17 radFddiPortFunctionalStatus= lerAlarm(2) 18 radFddiPortFunctionalStatus= lerCutoff(3) 19 ltalkPortJam = on(1) 20 ltalkPortTestResult = faulty(2) 21 clPortFunctionalStatus = faulty(2) 22 itrLinkFunctionalStatus = fail(2) or noRxClk(3) 23 fethPortFunctionalStatus = wrongSpeed(12) 24 lhsLinkStatus = linkFailure(2) 25 lntFddiPortRingConfiguration = isolate(5) 26 lntFddiPortRingConfiguration = wrap-a(2) or wrap-b(3) or wrap-s(4) 27 atmEdgePortHealthStatus = atmError(2) or atmInterfaceTCAlarmState = lcdFailure 28 fethPortDormantLinkFunctionalStatus = rld(2) or atmEdgePortDormantHealthStatus = atmError(2) 29 sonetSectionCurrentStatus = sonetSectionLOS or sonetSectionLOF or sonetLineCurrentStatus = sonetLineAIS or sonetPathCurrentStatus = sonetPathSTSLOP or sonetPathSTSAIS or sonetPathUnequipped or sonetPathSignalLabelMismatch 30 sonetLineCurrentStatus = sonetLineRDI or sonetPathCurrentStatus = sonetPathSTSRDI 31 genCTIPortSync = not ok(1) 32 genCTIPortRxAlarm = not ok(1) 33 genCTIPortTxAlarm = not ok(1) 34 atmEdgePortILMIStatus = down(2) 35 atmEdgePortSignalStatus = down(2) | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| genPortSWRdFault | 1.3.6.1.4.1.81.9.1.1.15 | ||
| Attribute that reports to the Agent of any fault occurs in the port for the Soft Redundancy application | |||
| OBJECT-TYPE | |||
| INTEGER | ok(1), fault(2) | ||
| genPortActivation | 1.3.6.1.4.1.81.9.1.1.16 | ||
| A disabled port neither transmits nor receives. The port must be Explicitly enabled to restore operation. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| genPortFunctionalStatus | 1.3.6.1.4.1.81.9.1.1.17 | ||
| The functional status of the port: ok(1) - fully functional port, transmitting and receiving packets. rld(2) - receive link down condition on the port - Indicates a cable or connector failure detected by the port H/W. rxJabber(3) - partition(8) - the port is in partition state. RemoteFault(10) - | |||
| OBJECT-TYPE | |||
| INTEGER | ok(1), rld(2), rxJabber(3), partition(8), remoteFault(10), notSupported(255) | ||
| genPortIfMap | 1.3.6.1.4.1.81.9.1.1.18 | ||
| This MIB object defines the mapping of the LANNET box port to a MIB-II interface. If the port corresponds to a stack of interfaces - like the case of ATM ports, the interface number of this port shows the lowest interface in the ifStack, the one that typically has a connector present. If value zero is returned, the mapping is impossible or unknown for this type of port. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| genPortVLANMode | 1.3.6.1.4.1.81.9.1.1.19 | ||
| This item defines the VLAN operation mode of the port: perPortOnly(1) - indicates that all received packets are mapped to the VLAN, defined on the port, and packets are transmitted in untagged format; dot1QTagging(2) - indicates that all received packets are mapped to VLANs according to 802.1Q standard. All transmitted packets are tagged according to the standard 802.1Q tagging; plusTagging(3) - indicates that all packets recieved and transmitted on that port are tagged according to Lannet_s PlusTagging scheme. This mode is used when inter-VLAN bridging should be supported; islTagging(4) - indicates that all packets recieved and transmitted on that port are tagged according to the proprietary ISL mode of Lannet; dot1QTaggingButPVID(5) - indicates that all received packets are mapped to VLANs according to 802.1Q standard. All transmitted packets are tagged according to the standard 802.1Q tagging, exluding packets that belong to the port_s VLAN,which are transmitted untagged. | |||
| OBJECT-TYPE | |||
| INTEGER | perPortOnly(1), dot1QTagging(2), plusTagging(3), islTagging(4), dot1QTaggingButPVID(5), notSupported(255) | ||
| genPortAdminPermission | 1.3.6.1.4.1.81.9.1.1.20 | ||
| This item defines whether or not the Agent is permitted to change a Port Status from Disable to Enable. Permit(1) - The agent is permitted to do so. NotPermit(2) - The agent is not permitted to do so. Default value is: permit(1). | |||
| OBJECT-TYPE | |||
| INTEGER | permit(1), notPermit(2), notSupported(255) | ||
| genPortName | 1.3.6.1.4.1.81.9.1.1.21 | ||
| Name of the port in ASCII format, mainly filled by network managers for easily recognize the specific use of a switched port. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..16) | ||
| genPortClassification | 1.3.6.1.4.1.81.9.1.1.22 | ||
| Classification assigned to this port. regular - this port is connected to regular stations. Topology changes that may occur on it will not generate the sending of topology change (notification) BPDUs, will not generate a fast aging on the local forwarding database, and will not be signaled by console if the port administrative status is disabled. valuable - this port is used as a backbone link or is connected to a valuable server. Topology changes that may occur on it will generate a fast aging on the local forwarding database, and if STA is enabled on the stack, the sending of topology change (notification) BPDUs. It will also be signaled and propagated by console even if the port administrative status is disabled or if STA is disabled on this port. | |||
| OBJECT-TYPE | |||
| INTEGER | regular(1), valuable(2), notSupported(255) | ||
| genPortVLANBindingMode | 1.3.6.1.4.1.81.9.1.1.23 | ||
| VLAN binding mode assigned to this port. static - this port supports only the egress VLAN list as configured manually in its corresponding dot1qVlanStaticEgressPort. This is the default VLAN Binding mode. bindToReceive - this port supports the whole range of 3K VLANs from VLAN ID 1 to 3071. bindToAll - this port supports the egress VLAN IDs for which dot1qVlanStaticTable rows exist. GVRP - this port supports the egress VLAN IDs configured manually in its corresponding dot1qVlanStaticEgressPort as well as VLAN IDs requested by the GVRP link partner. | |||
| OBJECT-TYPE | |||
| INTEGER | static(1), bindToReceive(2), bindToAll(3), gVRP(4), notSupported(255) | ||
| genIntPort | 1.3.6.1.4.1.81.10 | ||
| OBJECT IDENTIFIER | |||
| genIntPortTable | 1.3.6.1.4.1.81.10.1 | ||
| Table of configuration attributes of internal ports. Internal ports are physical and/or logical entities which transfer information and connect modules to the internal networks (buses). | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| GenIntPortEntry | |||
| genIntPortEntry | 1.3.6.1.4.1.81.10.1.1 | ||
| An entry in the table, containing data about a single port. | |||
| OBJECT-TYPE | |||
| GenIntPortEntry | |||
| genIntPortGroupId | 1.3.6.1.4.1.81.10.1.1.1 | ||
| Index which identifies the group inside the chassis for which this entry contains information. Equals the number of the slot by which the group containing the internal port is accessed. This value is never greater than chNumberOfSlots. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| genIntPortId | 1.3.6.1.4.1.81.10.1.1.2 | ||
| Index which identifies the port inside the group for which this entry contains information. This value is never greater than genGroupNumberOfIntPorts of the group to which the port belongs. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| genIntPortAdminStatus | 1.3.6.1.4.1.81.10.1.1.3 | ||
| Defines the capability of the internal port to transmit or receive data. A disabled internal port neither transmits or receives. The port must be explicitly enabled to restore operation. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| genIntPortActivityStatus | 1.3.6.1.4.1.81.10.1.1.4 | ||
| This attribute defines the status of internal ports that may be part of a redundancy scheme. notActive(1) - indicates a disabled port which cannot transmit or receive packets even if included in a redundancy scheme. dormant(2) - indicates an enabled port which does not transmit or receive packets, but because it is included in a redundancy scheme, it may at any moment become responsible packet transmission and reception. active(3) - indicates that the port transmits and receives packets, serving as the main path in the redundant configuration. | |||
| OBJECT-TYPE | |||
| INTEGER | notActive(1), dormant(2), active(3), notSupported(255) | ||
| genIntPortBusConnNumber | 1.3.6.1.4.1.81.10.1.1.5 | ||
| The value of this attribute defines the shared bus or virtual network to which the internal port is connected. The value '0' indicates that the port is disconnected from the bus. In switch environments (virtual net) 0 and 255 are read only values | |||
| OBJECT-TYPE | |||
| INTEGER | 0..255 | ||
| genIntPortBusConnType | 1.3.6.1.4.1.81.10.1.1.6 | ||
| The value of this attribute defines the type of the bus to which the internal port is connected. | |||
| OBJECT-TYPE | |||
| INTEGER | ethernet(1), token-ring(2), local-talk(3), fddi(4), high-speed(5), fastEthernet(6), xSwitch(7), atm(8), other(255) | ||
| genIntPortSpecificOID | 1.3.6.1.4.1.81.10.1.1.7 | ||
| This attribute provides the OID of another group containing additional more specific information regarding this instance. | |||
| OBJECT-TYPE | |||
| OBJECT IDENTIFIER | |||
| genIntPortMonitorMode | 1.3.6.1.4.1.81.10.1.1.8 | ||
| This attribute enables monitoring of a specified bus (RMON). | |||
| OBJECT-TYPE | |||
| INTEGER | on(1), off(2), notSupported(255) | ||
| softRedundancy | 1.3.6.1.4.1.81.11 | ||
| OBJECT IDENTIFIER | |||
| softRedundancyTable | 1.3.6.1.4.1.81.11.1 | ||
| Table of attributes which define software redundancy links defined by means of the chassis SNMP agents. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SoftRedundancyEntry | |||
| softRedundancyEntry | 1.3.6.1.4.1.81.11.1.1 | ||
| An entry in the table, containing data about a single software redundancy link. | |||
| OBJECT-TYPE | |||
| SoftRedundancyEntry | |||
| softRedundancyId | 1.3.6.1.4.1.81.11.1.1.1 | ||
| Index which identifies the software redundancy link which for which the current entry provides information. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| softRedundancyName | 1.3.6.1.4.1.81.11.1.1.2 | ||
| Logical name of the software redundancy link | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(1..15) | ||
| softRedundancyGroupId1 | 1.3.6.1.4.1.81.11.1.1.3 | ||
| ID of the group to which the main port on the software redundancy link belongs. This value is never greater than chNumberOfSlots. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| softRedundancyPortId1 | 1.3.6.1.4.1.81.11.1.1.4 | ||
| ID of the main port on the software redundancy link. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| softRedundancyGroupId2 | 1.3.6.1.4.1.81.11.1.1.5 | ||
| ID of the group to which the secondary port on the software redundancy link belongs. This value is never greater than chNumberOfSlots. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| softRedundancyPortId2 | 1.3.6.1.4.1.81.11.1.1.6 | ||
| ID of the secondary port on the software redundancy link. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| softRedundancyStatus | 1.3.6.1.4.1.81.11.1.1.7 | ||
| Status of the entry in the softRedundancy Table: valid(1) indicates that row is busy with meaningful values; createRequest(2) will be set by manager when creating a new row; underCreation(3) indicates that agent accepts create command and performs it; invalid(4) indicates that no meaningful values are present in the row. Managers set this value in order to transmit a 'Delete row' command to agent. | |||
| OBJECT-TYPE | |||
| INTEGER | valid(1), createRequest(2), underCreation(3), invalid(4) | ||
| softRedundancyGlobalStatus | 1.3.6.1.4.1.81.11.2 | ||
| This attribute is used to allow the user to preserve the information, configured in the SWRedundancy table, although not activating it. The user can disable it when STA is enable in the switch. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2), notSupported(255) | ||
| fastRedundancyTable | 1.3.6.1.4.1.81.11.3 | ||
| Table of attributes which define the unique fast redundancy link defined by means of the chassis SNMP agents. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| FastRedundancyEntry | |||
| fastRedundancyEntry | 1.3.6.1.4.1.81.11.3.1 | ||
| The unique entry in the table, containing data about the fast redundancy link. | |||
| OBJECT-TYPE | |||
| FastRedundancyEntry | |||
| fastRedundancyId | 1.3.6.1.4.1.81.11.3.1.1 | ||
| Index which identifies the fast redundancy link for which the current entry provides information. Since only a single entry is supported, it will be always 1. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| fastRedundancyName | 1.3.6.1.4.1.81.11.3.1.2 | ||
| Logical name of the fast redundancy link. The default value for this item is 'fast' | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(1..15) | ||
| fastRedundancyGroupId1 | 1.3.6.1.4.1.81.11.3.1.3 | ||
| ID of the group to which the main port on the fast redundancy link belongs. This value is never greater than chNumberOfSlots. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| fastRedundancyPortId1 | 1.3.6.1.4.1.81.11.3.1.4 | ||
| ID of the main port on the fast redundancy link. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| fastRedundancyGroupId2 | 1.3.6.1.4.1.81.11.3.1.5 | ||
| ID of the group to which the secondary port on the fast redundancy link belongs. This value is never greater than chNumberOfSlots. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| fastRedundancyPortId2 | 1.3.6.1.4.1.81.11.3.1.6 | ||
| ID of the secondary port on the fast redundancy link. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| fastRedundancyStatus | 1.3.6.1.4.1.81.11.3.1.7 | ||
| Status of the entry in the fastRedundancy Table: valid(1) indicates that the row is set with meaningful values; createRequest(2) will be set by Console when creating the row; underCreation(3) indicates that agent accepts create command and performs it; invalid(4) indicates that no meaningful values are present in the row. Console will set this value in order to transmit a 'Delete row' command to agent. | |||
| OBJECT-TYPE | |||
| INTEGER | valid(1), createRequest(2), underCreation(3), invalid(4) | ||
| ChGenAgEntry | |||
| SEQUENCE | |||
| INTEGER as chGenAgId | |||
| INTEGER as chGenAgType | |||
| INTEGER as chGenAgMgmtIfType | |||
| OCTET STRING as chGenAgAddr | |||
| OBJECT IDENTIFIER as chGenAgSpecificOID | |||
| IpAddress as chGenAgSLIPAddress | |||
| DisplayString as chGenAgTypeName | |||
| DisplayString as chGenAgEntMngVersion | |||
| IpAddress as chGenAgIpAddr | |||
| ChLntAgEntry | |||
| SEQUENCE | |||
| INTEGER as chLntAgId | |||
| IpAddress as chLntAgSLIPAddress | |||
| DisplayString as chLntAgSWVersion | |||
| DisplayString as chLntAgKernelVersion | |||
| DisplayString as chLntAgCoprocSWVersion | |||
| DisplayString as chLntAgSWFault | |||
| INTEGER as chLntAgMgmtBusSelection | |||
| INTEGER as chLntAgCoprocCommStatus | |||
| INTEGER as chLntAgCommDebugMode | |||
| INTEGER as chLntAgConfigChangeTraps | |||
| INTEGER as chLntAgFaultTraps | |||
| INTEGER as chLntAgTrafficThreshTraps | |||
| INTEGER as chLntAgGroupEnrollDeenrollTraps | |||
| INTEGER as chLntAgSoftFaultTraps | |||
| INTEGER as chLntAgHubEnrollTraps | |||
| INTEGER as chLntAgTempThreshTraps | |||
| OBJECT IDENTIFIER as chLntAgSpecificOID | |||
| OCTET STRING as chLntAgLastAddrConfig | |||
| OCTET STRING as chLntAgSecAddrConfig | |||
| INTEGER as chLntAgSoftwareStatus | |||
| DisplayString as chLntAgConfigurationSymbol | |||
| INTEGER as chLntAgIntTemp | |||
| DisplayString as chLntAgBootVersion | |||
| INTEGER as chLntAgSensorFault | |||
| INTEGER as chLntAgSensorFaultTraps | |||
| INTEGER as chLntAgInterProcFault | |||
| INTEGER as chLntAgInterProcFaultTraps | |||
| INTEGER as chLntAgPSUVoltThrsTraps | |||
| DisplayString as chLntAgHardwareVersion | |||
| DisplayString as chLntAgSoftwareDscr | |||
| INTEGER as chLntAgCAMChangeTraps | |||
| DisplayString as chLntAgAppVersion | |||
| ChLntAgPermMngrEntry | |||
| SEQUENCE | |||
| INTEGER as chLntAgPermMngrId | |||
| IpAddress as chLntAgPermMngrAddr | |||
| INTEGER as chLntAgMngrTraps | |||
| ChLntAgRmtNetEntry | |||
| SEQUENCE | |||
| INTEGER as chLntAgRmtNetId | |||
| IpAddress as chLntAgRmtNetAddr | |||
| IpAddress as chLntAgRmtNetMask | |||
| ChLntAgTrapsEntry | |||
| SEQUENCE | |||
| INTEGER as chLntAgTrapsPermMngrId | |||
| INTEGER as chLntAgTrapsId | |||
| INTEGER as chLntAgTrapsEnableFlag | |||
| ChHWPSUEntry | |||
| SEQUENCE | |||
| INTEGER as chHWPSUId | |||
| INTEGER as chHWPSUActivityStatus | |||
| INTEGER as chHWPSULocation | |||
| INTEGER as chHWPSUVoltage | |||
| INTEGER as chHWPSUVoltHighThresh | |||
| INTEGER as chHWPSUVoltLowThresh | |||
| AlarmPolicyEntry | |||
| SEQUENCE | |||
| INTEGER as alarmPolicyIndex | |||
| OBJECT IDENTIFIER as alarmPolicyParameterOID | |||
| INTEGER as alarmPolicyRisingFalling | |||
| INTEGER as alarmPolicyThresholdValue | |||
| INTEGER as alarmPolicySampleTimeInterval | |||
| INTEGER as alarmPolicySampleType | |||
| INTEGER as alarmPolicyActionPolicy | |||
| OCTET STRING as alarmPolicyBitmap | |||
| INTEGER as alarmPolicyStatus | |||
| VariableEntry | |||
| SEQUENCE | |||
| INTEGER as variablePolicy | |||
| INTEGER as variableInstance1 | |||
| INTEGER as variableInstance2 | |||
| INTEGER as variableStatus | |||
| ChLogFileEntry | |||
| SEQUENCE | |||
| INTEGER as chLogFileGroupId | |||
| INTEGER as chLogFileIndex | |||
| INTEGER as chLogFileName | |||
| Counter as chLogFileAbsoluteTime | |||
| DisplayString as chLogFileMessage | |||
| DisplayString as chLogFileEncryptedMessage | |||
| GenGroupEntry | |||
| SEQUENCE | |||
| INTEGER as genGroupId | |||
| DisplayString as genGroupSWVersion | |||
| DisplayString as genGroupKernelVersion | |||
| INTEGER as genGroupType | |||
| DisplayString as genGroupDescr | |||
| INTEGER as genGroupNumberOfPorts | |||
| INTEGER as genGroupNumberOfIntPorts | |||
| INTEGER as genGroupReset | |||
| INTEGER as genGroupAutoMan | |||
| OCTET STRING as genGroupFullConfig | |||
| INTEGER as genGroupRedun12 | |||
| INTEGER as genGroupRedun34 | |||
| INTEGER as genGroupRedun13-14 | |||
| INTEGER as genGroupStandAloneMode | |||
| INTEGER as genGroupInterProcCommStatus | |||
| INTEGER as genGroupCommStatus | |||
| INTEGER as genGroupHWStatus | |||
| INTEGER as genGroupSupplyVoltageFault | |||
| INTEGER as genGroupIntTemp | |||
| OBJECT IDENTIFIER as genGroupSpecificOID | |||
| DisplayString as genGroupConfigurationSymbol | |||
| TimeTicks as genGroupLastChange | |||
| INTEGER as genGroupRedunRecovery | |||
| DisplayString as genGroupHWVersion | |||
| INTEGER as genGroupHeight | |||
| INTEGER as genGroupWidth | |||
| OCTET STRING as genGroupIntrusionControl | |||
| OCTET STRING as genGroupThresholdStatus | |||
| OCTET STRING as genGroupEavesdropping | |||
| DisplayString as genGroupMainSWVersion | |||
| INTEGER as genGroupMPSActivityStatus | |||
| INTEGER as genGroupBUPSActivityStatus | |||
| INTEGER as genGroupPrepareCounters | |||
| OCTET STRING as genGroupPortLastChange | |||
| OCTET STRING as genGroupIntPortLastChange | |||
| OCTET STRING as genGroupFaultMask | |||
| DisplayString as genGroupTypeName | |||
| INTEGER as genGroupAgentSlot | |||
| INTEGER as genGroupMngType | |||
| INTEGER as genGroupNumberOfLogicalPorts | |||
| INTEGER as genGroupNumberOfInterfaces | |||
| INTEGER as genGroupCascadUpStatus | |||
| INTEGER as genGroupCascadDownStatus | |||
| INTEGER as genGroupSTARootPortID | |||
| OCTET STRING as genGroupCopyPortInstruction | |||
| OCTET STRING as genGroupLicenseKey | |||
| INTEGER as genGroupLogFileClear | |||
| DisplayString as genGroupBootVersion | |||
| TimeTicks as genGroupResetLastStamp | |||
| DisplayString as genGroupSerialNumber | |||
| DisplayString as genGroupShowModuleInformation | |||
| INTEGER as genGroupCascadingUpFault | |||
| INTEGER as genGroupCascadingDownFault | |||
| OCTET STRING as genGroupPortClassificationMask | |||
| GenPortEntry | |||
| SEQUENCE | |||
| INTEGER as genPortGroupId | |||
| INTEGER as genPortId | |||
| INTEGER as genPortFunctionality | |||
| INTEGER as genPortType | |||
| DisplayString as genPortDescr | |||
| INTEGER as genPortActivityStatus | |||
| OCTET STRING as genPortSecurityPolicy | |||
| OCTET STRING as genPortSecureAddresses | |||
| INTEGER as genPortIntPortConnection | |||
| INTEGER as genPortAdminStatus | |||
| OBJECT IDENTIFIER as genPortSpecificOID | |||
| OCTET STRING as genPortThresholdStatus | SIZE(4) | ||
| OCTET STRING as genPortEavesdropping | |||
| OCTET STRING as genPortFaultMask | |||
| INTEGER as genPortSWRdFault | |||
| INTEGER as genPortActivation | |||
| INTEGER as genPortFunctionalStatus | |||
| INTEGER as genPortIfMap | |||
| INTEGER as genPortVLANMode | |||
| INTEGER as genPortAdminPermission | |||
| DisplayString as genPortName | |||
| INTEGER as genPortClassification | |||
| INTEGER as genPortVLANBindingMode | |||
| GenIntPortEntry | |||
| SEQUENCE | |||
| INTEGER as genIntPortGroupId | |||
| INTEGER as genIntPortId | |||
| INTEGER as genIntPortAdminStatus | |||
| INTEGER as genIntPortActivityStatus | |||
| INTEGER as genIntPortBusConnNumber | |||
| INTEGER as genIntPortBusConnType | |||
| OBJECT IDENTIFIER as genIntPortSpecificOID | |||
| INTEGER as genIntPortMonitorMode | |||
| SoftRedundancyEntry | |||
| SEQUENCE | |||
| INTEGER as softRedundancyId | |||
| DisplayString as softRedundancyName | |||
| INTEGER as softRedundancyGroupId1 | |||
| INTEGER as softRedundancyPortId1 | |||
| INTEGER as softRedundancyGroupId2 | |||
| INTEGER as softRedundancyPortId2 | |||
| INTEGER as softRedundancyStatus | |||
| FastRedundancyEntry | |||
| SEQUENCE | |||
| INTEGER as fastRedundancyId | |||
| DisplayString as fastRedundancyName | |||
| INTEGER as fastRedundancyGroupId1 | |||
| INTEGER as fastRedundancyPortId1 | |||
| INTEGER as fastRedundancyGroupId2 | |||
| INTEGER as fastRedundancyPortId2 | |||
| INTEGER as fastRedundancyStatus | |||