CPQIDE-MIB

File: CPQIDE-MIB.mib (58623 bytes)

Imported modules

CPQHOST-MIB RFC1155-SMI RFC1213-MIB
RFC-1212 RFC-1215

Imported symbols

compaq enterprises Counter
Gauge DisplayString OBJECT-TYPE
TRAP-TYPE sysName cpqHoTrapFlags

Defined Objects

cpqIde 1.3.6.1.4.1.232.14
OBJECT IDENTIFIER    

cpqIdeMibRev 1.3.6.1.4.1.232.14.1
OBJECT IDENTIFIER    

cpqIdeMibRevMajor 1.3.6.1.4.1.232.14.1.1
The Major Revision level. A change in the major revision level represents a major change in the architecture of the MIB. A change in the major revision level may indicate a significant change in the information supported and/or the meaning of the supported information, correct interpretation of data may require a MIB document with the same major revision level.
OBJECT-TYPE    
  INTEGER 1..65535  

cpqIdeMibRevMinor 1.3.6.1.4.1.232.14.1.2
The Minor Revision level. A change in the minor revision level may represent some minor additional support; no changes to any pre-existing information has occurred.
OBJECT-TYPE    
  INTEGER 0..65535  

cpqIdeMibCondition 1.3.6.1.4.1.232.14.1.3
The overall condition. This object represents the overall status of the Ide system represented by this MIB.
OBJECT-TYPE    
  INTEGER other(1), ok(2), degraded(3), failed(4)  

cpqIdeComponent 1.3.6.1.4.1.232.14.2
OBJECT IDENTIFIER    

cpqIdeInterface 1.3.6.1.4.1.232.14.2.1
OBJECT IDENTIFIER    

cpqIdeOsCommon 1.3.6.1.4.1.232.14.2.1.4
OBJECT IDENTIFIER    

cpqIdeOsCommonPollFreq 1.3.6.1.4.1.232.14.2.1.4.1
The Insight Agent's polling frequency. The frequency, in seconds, at which the Insight Agent requests information from the device driver. A frequency of zero indicates that the Insight Agent retrieves the information upon request of a management station, it does not poll the device driver at a specific interval. If the poll frequency is zero (0) all attempts to write to this object will fail. If the poll frequency is non-zero, setting this value will change the polling frequency of the Insight Agent. Setting the poll frequency to zero will always fail, an agent may also choose to fail any request to change the poll frequency to a value that would severely impact system performance.
OBJECT-TYPE    
  INTEGER 0..65535  

cpqIdeOsCommonModuleTable 1.3.6.1.4.1.232.14.2.1.4.2
A table of software modules that provide an interface to the device this MIB describes.
OBJECT-TYPE    
  SEQUENCE OF  
    CpqIdeOsCommonModuleEntry

cpqIdeOsCommonModuleEntry 1.3.6.1.4.1.232.14.2.1.4.2.1
A description of a software modules that provide an interface to the device this MIB describes.
OBJECT-TYPE    
  CpqIdeOsCommonModuleEntry  

cpqIdeOsCommonModuleIndex 1.3.6.1.4.1.232.14.2.1.4.2.1.1
A unique index for this module description.
OBJECT-TYPE    
  INTEGER 0..255  

cpqIdeOsCommonModuleName 1.3.6.1.4.1.232.14.2.1.4.2.1.2
The module name.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

cpqIdeOsCommonModuleVersion 1.3.6.1.4.1.232.14.2.1.4.2.1.3
The module version in XX.YY format. Where XX is the major version number and YY is the minor version number. This field will be a null (size 0) string if the agent cannot provide the module version.
OBJECT-TYPE    
  DisplayString SIZE(0..5)  

cpqIdeOsCommonModuleDate 1.3.6.1.4.1.232.14.2.1.4.2.1.4
The module date. field octets contents range ===== ====== ======= ===== 1 1-2 year 0..65536 2 3 month 1..12 3 4 day 1..31 4 5 hour 0..23 5 6 minute 0..59 6 7 second 0..60 (use 60 for leap-second) This field will be set to year = 0 if the agent cannot provide the module date. The hour, minute, and second field will be set to zero (0) if they are not relevant.
OBJECT-TYPE    
  OCTET STRING SIZE(7)  

cpqIdeOsCommonModulePurpose 1.3.6.1.4.1.232.14.2.1.4.2.1.5
The purpose of the module described in this entry.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

cpqIdeIdent 1.3.6.1.4.1.232.14.2.2
OBJECT IDENTIFIER    

cpqIdeIdentTable 1.3.6.1.4.1.232.14.2.2.1
IDE Drive Identification Table.
OBJECT-TYPE    
  SEQUENCE OF  
    CpqIdeIdentEntry

cpqIdeIdentEntry 1.3.6.1.4.1.232.14.2.2.1.1
IDE Identification Table Entry.
OBJECT-TYPE    
  CpqIdeIdentEntry  

cpqIdeIdentIndex 1.3.6.1.4.1.232.14.2.2.1.1.1
An index that uniquely specifies each device. For disks, this index value will match the value of the cpqSeFixedDiskIndex in the Standard Equipment MIB (CPQSTDEQ.MIB) when the same disk is being described. Each possible index value indicates a specific drive as shown in the table below: Drive Index IDE Controller Drive Unit =========== ============== ========== 0 Primary 1 1 Primary 2 2 Secondary 1 3 Secondary 2 Any other index value would be implementation specific.
OBJECT-TYPE    
  INTEGER 0..65535  

cpqIdeIdentModel 1.3.6.1.4.1.232.14.2.2.1.1.2
IDE Drive Model. The is the drive model name and can be used for identification purposes.
OBJECT-TYPE    
  DisplayString SIZE(0..41)  

cpqIdeIdentSerNum 1.3.6.1.4.1.232.14.2.2.1.1.3
IDE Drive Serial Number. The is the drive serial number and can be used for identification purposes.
OBJECT-TYPE    
  DisplayString SIZE(0..21)  

cpqIdeIdentFWVers 1.3.6.1.4.1.232.14.2.2.1.1.4
IDE Firmware Version. This is the version of the firmware on the IDE drive. If the IDE drive firmware version is unavailable, then this string will be of length zero (0).
OBJECT-TYPE    
  DisplayString SIZE(0..9)  

cpqIdeIdentCondition 1.3.6.1.4.1.232.14.2.2.1.1.5
IDE Drive Condition. This is the overall condition of the IDE drive. The following values are defined: other(1) The drive does not support drive condition monitoring. ok(2) The drive is operating normally. No user action is required. degraded(3) The drive is degraded. The drive may need to be replaced. failed(4) The drive has failed. The drive should be replaced.
OBJECT-TYPE    
  INTEGER other(1), ok(2), degraded(3), failed(4)  

cpqIdeIdentErrorNumber 1.3.6.1.4.1.232.14.2.2.1.1.6
IDE Error Number. This value represents the error code associated with a failing IDE drive.
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

cpqIdeIdentType 1.3.6.1.4.1.232.14.2.2.1.1.7
IDE Device Type. This is the type of ATAPI device. The following types are defined: other(1) The Insight agent does not recognize this type. You may need to upgrade your software. disk(2) This is a direct-access device like a disk drive. tape(3) This is a sequential-access device like a tape drive. printer(4) This is a printer device. processor(5) This is a processor device. worm(6) This is a write-once, read-many times device. cd-rom(7) This is a CD or DVD device. scanner(8) This is a scanner device. optical(9) This is an optical memory device. jukeBox(10) This is a media changer device like a jukebox. commDev(11) This is a communications device like a LAN bridge.
OBJECT-TYPE    
  INTEGER other(1), disk(2), tape(3), printer(4), processor(5), wormDrive(6), cd-rom(7), scanner(8), optical(9), jukeBox(10), commDev(11)  

cpqIdeIdentTypeExtended 1.3.6.1.4.1.232.14.2.2.1.1.8
IDE Extended Device Type. This is additional information about the type of IDE device. The following types are defined: other(1) This target does not have any extended type information. pdcd(2) This is a power-drive CD-ROM. removableDisk(3) This is a removable media disk device like a floppy drive.
OBJECT-TYPE    
  INTEGER other(1), pdcd(2), removableDisk(3)  

cpqIdeIdentCondition2 1.3.6.1.4.1.232.14.2.2.1.1.9
IDE Drive Condition. This is the overall condition of the IDE drive. The following values are defined: other(1) The drive does not support drive condition monitoring. ok(2) The drive is operating normally. No user action is required. degraded(3) The drive is degraded. See cpqIdeIdentStatus for the appropriate action. failed(4) The drive has failed. See cpqIdeIdentStatus for the appropriate action.
OBJECT-TYPE    
  INTEGER other(1), ok(2), degraded(3), failed(4)  

cpqIdeIdentStatus 1.3.6.1.4.1.232.14.2.2.1.1.10
IDE Drive Satus. This indicates the status of the IDE drive. The following values are defined: other(1) The drive does not support drive status monitoring. ok(2) The drive is operating normally. No user action is required. preFailureDegraded(3) The drive has detected that at least one pre-failure SMART attribute has gone out of range. The drive may need to be replaced. ultraAtaDegraded(4) The Ultra ATA Integrity Monitor has detected data transmission errors between the hard drive and processor. For best performance, move Ultra ATA devices to the primary controller and non Ultra ATA devices to the secondary controller. If errors still persist, consider replacing the standard 40-conductor cable with and 80-conductor cable.
OBJECT-TYPE    
  INTEGER other(1), ok(2), preFailureDegraded(3), ultraAtaDegraded(4)  

cpqIdeIdentUltraAtaAvailability 1.3.6.1.4.1.232.14.2.2.1.1.11
This describes the availability of Ultra ATA transfers between this device and the controller. The following values are defined: other(1) The agents do not support reporting this variable or the agent need to be upgraded. noNotSupportedByDeviceAndController(2), The device and the controller do not support Ultra ATA. noNotSupportedByDevice(3), The device does not support Ultra ATA but the controller does support Ultra ATA. noNotSupportedByController(4), The controller does not support Ultra ATA but the device does support Ultra ATA. NoDisabledInSetup(5), The device and the controller do support Ultra ATA but it has been disabled in F10 Setup. yesEnabledInSetup(6), The device and the controller do support Ultra ATA and it is enabled in F10 Setup.
OBJECT-TYPE    
  INTEGER other(1), noNotSupportedByDeviceAndController(2), noNotSupportedByDevice(3), noNotSupportedByController(4), noDisabledInSetup(5), yesEnabledInSetup(6)  

cpqIdeController 1.3.6.1.4.1.232.14.2.3
OBJECT IDENTIFIER    

cpqIdeControllerTable 1.3.6.1.4.1.232.14.2.3.1
IDE Controller Table.
OBJECT-TYPE    
  SEQUENCE OF  
    CpqIdeControllerEntry

cpqIdeControllerEntry 1.3.6.1.4.1.232.14.2.3.1.1
IDE Controller Table Entry.
OBJECT-TYPE    
  CpqIdeControllerEntry  

cpqIdeControllerIndex 1.3.6.1.4.1.232.14.2.3.1.1.1
An index that uniquely identifies each controller.
OBJECT-TYPE    
  INTEGER  

cpqIdeControllerOverallCondition 1.3.6.1.4.1.232.14.2.3.1.1.2
IDE Controller Overall Condition. This is the overall condition of the IDE controller and any associated devices.
OBJECT-TYPE    
  INTEGER other(1), ok(2), degraded(3), failed(4)  

cpqIdeControllerModel 1.3.6.1.4.1.232.14.2.3.1.1.3
IDE Controller Model. The is the IDE controller model name.
OBJECT-TYPE    
  DisplayString  

cpqIdeControllerFwRev 1.3.6.1.4.1.232.14.2.3.1.1.4
IDE Controller Firmware Revision. The is the IDE controller firmware revision.
OBJECT-TYPE    
  DisplayString  

cpqIdeControllerSlot 1.3.6.1.4.1.232.14.2.3.1.1.5
IDE Controller Slot. This identifies the physical slot where the IDE controller resides in the system. For example, if this value is three, the controller is located in slot three of your computer. If the value cannot be determined or is not applicable, the value is set to -1.
OBJECT-TYPE    
  INTEGER  

cpqIdeControllerStatus 1.3.6.1.4.1.232.14.2.3.1.1.6
IDE Channel Host Controller Status. The host controller can be in one of the following states: Other (1) The agent is unable to determine the status of the controller. OK (2) Indicates that the controller is in normal operation mode. Failed (3) Indicates that the host controller has failed and should be replaced.
OBJECT-TYPE    
  INTEGER other(1), ok(2), failed(3)  

cpqIdeControllerCondition 1.3.6.1.4.1.232.14.2.3.1.1.7
IDE Controller Condition. This is the condition of the IDE controller.
OBJECT-TYPE    
  INTEGER other(1), ok(2), degraded(3), failed(4)  

cpqIdeControllerSerialNumber 1.3.6.1.4.1.232.14.2.3.1.1.8
IDE Controller Serial Number. The is the IDE controller serial number. A NULL string indicates that the serial number could not be determined or is irrelevant.
OBJECT-TYPE    
  DisplayString  

cpqIdeAtaDisk 1.3.6.1.4.1.232.14.2.4
OBJECT IDENTIFIER    

cpqIdeAtaDiskTable 1.3.6.1.4.1.232.14.2.4.1
IDE ATA Disk Table.
OBJECT-TYPE    
  SEQUENCE OF  
    CpqIdeAtaDiskEntry

cpqIdeAtaDiskEntry 1.3.6.1.4.1.232.14.2.4.1.1
IDE ATA Disk Table Entry.
OBJECT-TYPE    
  CpqIdeAtaDiskEntry  

cpqIdeAtaDiskControllerIndex 1.3.6.1.4.1.232.14.2.4.1.1.1
An index that uniquely identifies each controller.
OBJECT-TYPE    
  INTEGER  

cpqIdeAtaDiskIndex 1.3.6.1.4.1.232.14.2.4.1.1.2
An index that uniquely identifies each disk.
OBJECT-TYPE    
  INTEGER  

cpqIdeAtaDiskModel 1.3.6.1.4.1.232.14.2.4.1.1.3
ATA Disk Model. The is the model name of the ATA disk.
OBJECT-TYPE    
  DisplayString  

cpqIdeAtaDiskFwRev 1.3.6.1.4.1.232.14.2.4.1.1.4
ATA Disk Firmware Revision. The is the firmware revision of the ATA disk.
OBJECT-TYPE    
  DisplayString  

cpqIdeAtaDiskSerialNumber 1.3.6.1.4.1.232.14.2.4.1.1.5
ATA Disk Serial Number. The is the serial number of the ATA disk.
OBJECT-TYPE    
  DisplayString  

cpqIdeAtaDiskStatus 1.3.6.1.4.1.232.14.2.4.1.1.6
ATA Disk Status. This is the status of the ATA disk.
OBJECT-TYPE    
  INTEGER other(1), ok(2), smartError(3), failed(4)  

cpqIdeAtaDiskCondition 1.3.6.1.4.1.232.14.2.4.1.1.7
ATA Disk Condition. This is the condition of the ATA disk.
OBJECT-TYPE    
  INTEGER other(1), ok(2), degraded(3), failed(4)  

cpqIdeAtaDiskCapacity 1.3.6.1.4.1.232.14.2.4.1.1.8
ATA Disk Capacity. This is the capacity of the ATA disk in megabytes.
OBJECT-TYPE    
  INTEGER  

cpqIdeAtaDiskSmartEnabled 1.3.6.1.4.1.232.14.2.4.1.1.9
ATA Disk S.M.A.R.T Enabled? other(1) The agent cannot determine the state of S.M.A.R.T. monitoring on this ATA disk. true(2) The ATA disk has S.M.A.R.T motitoring enabled. false(3) The ATA disk does not have S.M.A.R.T motitoring enabled.
OBJECT-TYPE    
  INTEGER other(1), true(2), false(3)  

cpqIdeAtaDiskTransferMode 1.3.6.1.4.1.232.14.2.4.1.1.10
ATA Disk Transfer Mode. other(1) The agent cannot determine the transfer mode on this ATA disk. pioMode0(2) The ATA disk is using PIO mode 0. pioMode1(3) The ATA disk is using PIO mode 1. pioMode2(4) The ATA disk is using PIO mode 2. pioMode3(5) The ATA disk is using PIO mode 3. pioMode4(6) The ATA disk is using PIO mode 4. dmaMode0(7) The ATA disk is using DMA mode 0. dmaMode1(8) The ATA disk is using DMA mode 1. dmaMode2(9) The ATA disk is using DMA mode 2. ultraDmaMode0(10) The ATA disk is using Ultra DMA mode 0. ultraDmaMode1(11) The ATA disk is using Ultra DMA mode 1. ultraDmaMode2(12) The ATA disk is using Ultra DMA mode 2. ultraDmaMode3(13) The ATA disk is using Ultra DMA mode 3. ultraDmaMode4(14) The ATA disk is using Ultra DMA mode 4. ultraDmaMode5(15) The ATA disk is using Ultra DMA mode 5.
OBJECT-TYPE    
  INTEGER other(1), pioMode0(2), pioMode1(3), pioMode2(4), pioMode3(5), pioMode4(6), dmaMode0(7), dmaMode1(8), dmaMode2(9), ultraDmaMode0(10), ultraDmaMode1(11), ultraDmaMode2(12), ultraDmaMode3(13), ultraDmaMode4(14), ultraDmaMode5(15)  

cpqIdeAtaDiskChannel 1.3.6.1.4.1.232.14.2.4.1.1.11
ATA Disk Channel. other(1) The agent cannot determine the channel to which the ATA disk is attached. channel0(2) The ATA disk is attached to the primary channel. channel1(3) The ATA disk is attached to the secondary channel. serial(4) The disk is attached to the serial interface and channel no longer applies.
OBJECT-TYPE    
  INTEGER other(1), channel0(2), channel1(3), serial(4)  

cpqIdeAtaDiskNumber 1.3.6.1.4.1.232.14.2.4.1.1.12
ATA Disk Number. other(1) The agent cannot determine the number of the ATA disk. device0(2) The ATA disk is device 0 (master). device1(3) The ATA disk is device 1 (slave). sataDevice0(4) The SATA disk is device 0. sataDevice1(5) The SATA disk is device 1. sataDevice2(6) The SATA disk is device 2. sataDevice3(7) The SATA disk is device 3. sataDevice4(8) The SATA disk is device 4. sataDevice5(9) The SATA disk is device 5. sataDevice6(10) The SATA disk is device 6. sataDevice7(11) The SATA disk is device 7. bay1(21) The disk is in bay 1. bay2(22) The disk is in bay 2. bay3(23) The disk is in bay 3. bay4(24) The disk is in bay 4. bay5(25) The disk is in bay 5. bay6(26) The disk is in bay 6. bay7(27) The disk is in bay 7. bay8(28) The disk is in bay 8.
OBJECT-TYPE    
  INTEGER other(1), device0(2), device1(3), sataDevice0(4), sataDevice1(5), sataDevice2(6), sataDevice3(7), sataDevice4(8), sataDevice5(9), sataDevice6(10), sataDevice7(11), bay1(21), bay2(22), bay3(23), bay4(24), bay5(25), bay6(26), bay7(27), bay8(28)  

cpqIdeAtaDiskLogicalDriveMember 1.3.6.1.4.1.232.14.2.4.1.1.13
Logical Drive Membership? other(1) The agent cannot determine if the ATA disk is part of a logical drive. true(2) The ATA disk is part of a logical drive. false(3) The ATA disk is not part of a logical drive.
OBJECT-TYPE    
  INTEGER other(1), true(2), false(3)  

cpqIdeAtaDiskIsSpare 1.3.6.1.4.1.232.14.2.4.1.1.14
ATA Disk Spare? other(1) The agent cannot determine if the ATA disk is a spare. true(2) The ATA disk is a spare disk. false(3) The ATA disk is not a spare disk.
OBJECT-TYPE    
  INTEGER other(1), true(2), false(3)  

cpqIdeAtaDiskOsName 1.3.6.1.4.1.232.14.2.4.1.1.15
ATA Disk OS Name. The OS name for this ATA disk. This field will be a null (size 0) string if the agent does not support OS name or if the ATA disk is part of a logical drive.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

cpqIdeAtaDiskType 1.3.6.1.4.1.232.14.2.4.1.1.16
ATA Disk Type other(1) The agent cannot determine the disk type. ata(2) The disk type is parallel ATA. sata(3) The disk type is Serial ATA.
OBJECT-TYPE    
  INTEGER other(1), ata(2), sata(3)  

cpqIdeAtaDiskSataVersion 1.3.6.1.4.1.232.14.2.4.1.1.17
Physical Drive SATA Version. The following values are defined: other(1) The agent is unable to determine the SATA version for this disk or it is not a SATA disk. sataOne(2) The disk is SATA version one. sataTwo(3) The disk is SATA version two.
OBJECT-TYPE    
  INTEGER other(1), sataOne(2), sataTwo(3)  

cpqIdeAtapiDevice 1.3.6.1.4.1.232.14.2.5
OBJECT IDENTIFIER    

cpqIdeAtapiDeviceTable 1.3.6.1.4.1.232.14.2.5.1
IDE ATAPI Device Table.
OBJECT-TYPE    
  SEQUENCE OF  
    CpqIdeAtapiDeviceEntry

cpqIdeAtapiDeviceEntry 1.3.6.1.4.1.232.14.2.5.1.1
IDE ATAPI Device Table Entry.
OBJECT-TYPE    
  CpqIdeAtapiDeviceEntry  

cpqIdeAtapiDeviceControllerIndex 1.3.6.1.4.1.232.14.2.5.1.1.1
An index that uniquely identifies each controller.
OBJECT-TYPE    
  INTEGER  

cpqIdeAtapiDeviceIndex 1.3.6.1.4.1.232.14.2.5.1.1.2
An index that uniquely identifies each ATAPI device.
OBJECT-TYPE    
  INTEGER  

cpqIdeAtapiDeviceModel 1.3.6.1.4.1.232.14.2.5.1.1.3
ATAPI Device Model. The is the model name of the ATAPI device.
OBJECT-TYPE    
  DisplayString  

cpqIdeAtapiDeviceFwRev 1.3.6.1.4.1.232.14.2.5.1.1.4
ATAPI Device Firmware Revision. The is the firmware revision of the ATAPI device.
OBJECT-TYPE    
  DisplayString  

cpqIdeAtapiDeviceType 1.3.6.1.4.1.232.14.2.5.1.1.5
ATAPI Device Type. This is the type of ATAPI device. The following types are defined: other(1) The agent does not recognize this type. You may need to upgrade your software. disk(2) This is a direct-access device like a disk drive. tape(3) This is a sequential-access device like a tape drive. printer(4) This is a printer device. processor(5) This is a processor device. worm(6) This is a write-once, read-many times device. cd-rom(7) This is a CD or DVD device. scanner(8) This is a scanner device. optical(9) This is an optical memory device. jukeBox(10) This is a media changer device like a jukebox. commDev(11) This is a communications device like a LAN bridge.
OBJECT-TYPE    
  INTEGER other(1), disk(2), tape(3), printer(4), processor(5), wormDrive(6), cd-rom(7), scanner(8), optical(9), jukeBox(10), commDev(11)  

cpqIdeAtapiDeviceTypeExtended 1.3.6.1.4.1.232.14.2.5.1.1.6
ATAPI Extended Device Type. This is additional information about the type of ATAPI device. The following types are defined: other(1) This target does not have any extended type information. pdcd(2) This is a power-drive CD-ROM. removableDisk(3) This is a removable media disk device like a floppy drive.
OBJECT-TYPE    
  INTEGER other(1), pdcd(2), removableDisk(3)  

cpqIdeAtapiDeviceChannel 1.3.6.1.4.1.232.14.2.5.1.1.7
ATAPI Device Channel. other(1) The agent cannot determine the channel to which the ATAPI device is attached. channel0(2) The ATAPI device is attached to the primary channel. channel1(3) The ATAPI device is attached to the secondary channel.
OBJECT-TYPE    
  INTEGER other(1), channel0(2), channel1(3)  

cpqIdeAtapiDeviceNumber 1.3.6.1.4.1.232.14.2.5.1.1.8
ATAPI Device Number. other(1) The agent cannot determine the number of the ATAPI device. device0(2) The ATAPI device is device 0 (master). device1(3) The ATAPI device is device 1 (slave).
OBJECT-TYPE    
  INTEGER other(1), device0(2), device1(3)  

cpqIdeLogicalDrive 1.3.6.1.4.1.232.14.2.6
OBJECT IDENTIFIER    

cpqIdeLogicalDriveTable 1.3.6.1.4.1.232.14.2.6.1
IDE Logical Drive Table.
OBJECT-TYPE    
  SEQUENCE OF  
    CpqIdeLogicalDriveEntry

cpqIdeLogicalDriveEntry 1.3.6.1.4.1.232.14.2.6.1.1
IDE Logical Drive Table Entry.
OBJECT-TYPE    
  CpqIdeLogicalDriveEntry  

cpqIdeLogicalDriveControllerIndex 1.3.6.1.4.1.232.14.2.6.1.1.1
An index that uniquely identifies each controller.
OBJECT-TYPE    
  INTEGER  

cpqIdeLogicalDriveIndex 1.3.6.1.4.1.232.14.2.6.1.1.2
An index that uniquely identifies each logical drive.
OBJECT-TYPE    
  INTEGER  

cpqIdeLogicalDriveRaidLevel 1.3.6.1.4.1.232.14.2.6.1.1.3
IDE Logical Drive RAID Level. The following RAID levels are defined: other(1) The agent cannot determine the RAID level of this logical drive. raid0(2) The logical drive is configured with RAID level 0. raid1(3) The logical drive is configured with RAID level 1. raid0plus1(4) The logical drive is configured with RAID level 0 plus 1. raid5(5) The logical drive is configured with RAID level 5. raid15(6) The logical drive is configured with RAID level 1 plus 5. volume(7) The logical drive is configured as a volume set.
OBJECT-TYPE    
  INTEGER other(1), raid0(2), raid1(3), raid0plus1(4), raid5(5), raid15(6), volume(7)  

cpqIdeLogicalDriveCapacity 1.3.6.1.4.1.232.14.2.6.1.1.4
IDE Logical Drive Capacity. This is the capacity of the logical drive in megabytes.
OBJECT-TYPE    
  INTEGER  

cpqIdeLogicalDriveStatus 1.3.6.1.4.1.232.14.2.6.1.1.5
IDE Logical Drive Status. This is the status of the logical drive. other(1) The agent cannot determine the logical drive status. ok(2) Indicates that the logical drive is in normal operation mode. degraded(3) Indicates that at least one physical drive has failed, but the logical drive's RAID level lets the drive continue to operate with no data loss. rebuilding(4) Indicates that the logical drive is rebuilding a physical drive. When complete, the logical drive will return to normal operation. failed(5) Indicates that more physical drives have failed than the RAID level of the logical drive can handle without data loss.
OBJECT-TYPE    
  INTEGER other(1), ok(2), degraded(3), rebuilding(4), failed(5)  

cpqIdeLogicalDriveCondition 1.3.6.1.4.1.232.14.2.6.1.1.6
IDE Logical Drive Condition. This is the condition of the logical drive.
OBJECT-TYPE    
  INTEGER other(1), ok(2), degraded(3), failed(4)  

cpqIdeLogicalDriveDiskIds 1.3.6.1.4.1.232.14.2.6.1.1.7
IDE Logical Drive Disk ID list. This lists the ATA disks drive IDs which are associated with this logical drive. These are the same IDs which can be used as indices into the ATA disk table (cpqIdeAtaDiskIndex). Each byte of the string is an index.
OBJECT-TYPE    
  OCTET STRING SIZE(0..255)  

cpqIdeLogicalDriveStripeSize 1.3.6.1.4.1.232.14.2.6.1.1.8
IDE Logical Drive Stripe Size. This is the stripe size in kilobytes.
OBJECT-TYPE    
  INTEGER  

cpqIdeLogicalDriveSpareIds 1.3.6.1.4.1.232.14.2.6.1.1.9
IDE Logical Drive Spare ID list. This lists the ATA disks drive IDs which are possible spares for this logical drive. These are the same IDs which can be used as indices into the ATA disk table (cpqIdeAtaDiskIndex). Each byte of the string is an index.
OBJECT-TYPE    
  OCTET STRING SIZE(0..255)  

cpqIdeLogicalDriveRebuildingDisk 1.3.6.1.4.1.232.14.2.6.1.1.10
IDE Logical Drive Rebuilding Disk. This is the ATA disk that is in the process of rebuilding. If no drive is currently rebuilding, a value of -1 will be returned.
OBJECT-TYPE    
  INTEGER  

cpqIdeLogicalDriveOsName 1.3.6.1.4.1.232.14.2.6.1.1.11
IDE Logical Drive OS Name. The OS name for this logical drive. This field will be a null (size 0) string if the agent does not support OS name.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

cpqIdeDriveDegraded 1.3.6.1.4.1.232.14001
An IDE drive status has been set to degraded. User Action: The drive should be scheduled for replacement. Refer to the appropriate Maintenance and Service Guide for detailed information on a component replacement.
TRAP-TYPE    
  sysName  
  cpqHoTrapFlags  
  cpqIdeIdentIndex  

cpqIdeDriveOk 1.3.6.1.4.1.232.14002
An IDE drive status has been set to ok. User Action: None.
TRAP-TYPE    
  sysName  
  cpqHoTrapFlags  
  cpqIdeIdentIndex  

cpqIdeDriveUltraAtaDegraded 1.3.6.1.4.1.232.14003
An IDE drive detects an excessive number of Ultra ATA data transmission errors between the hard drive and the processor. User Action: For best performance move Ultra ATA devices to the primary controller and non Ultra ATA devices to the secondary controller. If errors still persist, consider replacing the standard 40-conductor IDE cable with an 80-conductor Ultra ATA cable.
TRAP-TYPE    
  sysName  
  cpqHoTrapFlags  
  cpqIdeIdentIndex  

cpqIdeAtaDiskStatusChange 1.3.6.1.4.1.232.14004
ATA Disk Status Change. This trap signifies that the agent has detected a change in the status of an ATA disk drive. The variable cpqIdeAtaDiskStatus indicates the current disk drive status. User Action: If the physical drive status is smartError(3) or failed(4), replace the drive.
TRAP-TYPE    
  sysName  
  cpqHoTrapFlags  
  cpqIdeAtaDiskControllerIndex  
  cpqIdeAtaDiskIndex  
  cpqIdeAtaDiskModel  
  cpqIdeAtaDiskFwRev  
  cpqIdeAtaDiskSerialNumber  
  cpqIdeAtaDiskStatus  
  cpqIdeAtaDiskChannel  
  cpqIdeAtaDiskNumber  

cpqIdeLogicalDriveStatusChange 1.3.6.1.4.1.232.14005
IDE Logical Drive Status Change. This trap signifies that the agent has detected a change in the status of an IDE logical drive. The variable cpqIdeLogicalDriveStatus indicates the current logical drive status. User Action: If the logical drive status is failed(5), examine the array for failed drives that need replacement.
TRAP-TYPE    
  sysName  
  cpqHoTrapFlags  
  cpqIdeControllerModel  
  cpqIdeControllerSlot  
  cpqIdeLogicalDriveControllerIndex  
  cpqIdeLogicalDriveIndex  
  cpqIdeLogicalDriveStatus  

Defined Objects

CpqIdeOsCommonModuleEntry  
SEQUENCE    
  INTEGER as cpqIdeOsCommonModuleIndex  
  DisplayString as cpqIdeOsCommonModuleName  
  DisplayString as cpqIdeOsCommonModuleVersion  
  OCTET STRING as cpqIdeOsCommonModuleDate  
  DisplayString as cpqIdeOsCommonModulePurpose  

CpqIdeIdentEntry  
SEQUENCE    
  INTEGER as cpqIdeIdentIndex  
  DisplayString as cpqIdeIdentModel  
  DisplayString as cpqIdeIdentSerNum  
  DisplayString as cpqIdeIdentFWVers  
  INTEGER as cpqIdeIdentCondition  
  DisplayString as cpqIdeIdentErrorNumber  
  INTEGER as cpqIdeIdentType  
  INTEGER as cpqIdeIdentTypeExtended  
  INTEGER as cpqIdeIdentCondition2  
  INTEGER as cpqIdeIdentStatus  
  INTEGER as cpqIdeIdentUltraAtaAvailability  

CpqIdeControllerEntry  
SEQUENCE    
  INTEGER as cpqIdeControllerIndex  
  INTEGER as cpqIdeControllerOverallCondition  
  DisplayString as cpqIdeControllerModel  
  DisplayString as cpqIdeControllerFwRev  
  INTEGER as cpqIdeControllerSlot  
  INTEGER as cpqIdeControllerStatus  
  INTEGER as cpqIdeControllerCondition  
  DisplayString as cpqIdeControllerSerialNumber  

CpqIdeAtaDiskEntry  
SEQUENCE    
  INTEGER as cpqIdeAtaDiskControllerIndex  
  INTEGER as cpqIdeAtaDiskIndex  
  DisplayString as cpqIdeAtaDiskModel  
  DisplayString as cpqIdeAtaDiskFwRev  
  DisplayString as cpqIdeAtaDiskSerialNumber  
  INTEGER as cpqIdeAtaDiskStatus  
  INTEGER as cpqIdeAtaDiskCondition  
  INTEGER as cpqIdeAtaDiskCapacity  
  INTEGER as cpqIdeAtaDiskSmartEnabled  
  INTEGER as cpqIdeAtaDiskTransferMode  
  INTEGER as cpqIdeAtaDiskChannel  
  INTEGER as cpqIdeAtaDiskNumber  
  INTEGER as cpqIdeAtaDiskLogicalDriveMember  
  INTEGER as cpqIdeAtaDiskIsSpare  
  DisplayString as cpqIdeAtaDiskOsName  
  INTEGER as cpqIdeAtaDiskType  
  INTEGER as cpqIdeAtaDiskSataVersion  

CpqIdeAtapiDeviceEntry  
SEQUENCE    
  INTEGER as cpqIdeAtapiDeviceControllerIndex  
  INTEGER as cpqIdeAtapiDeviceIndex  
  DisplayString as cpqIdeAtapiDeviceModel  
  DisplayString as cpqIdeAtapiDeviceFwRev  
  INTEGER as cpqIdeAtapiDeviceType  
  INTEGER as cpqIdeAtapiDeviceTypeExtended  
  INTEGER as cpqIdeAtapiDeviceChannel  
  INTEGER as cpqIdeAtapiDeviceNumber  

CpqIdeLogicalDriveEntry  
SEQUENCE    
  INTEGER as cpqIdeLogicalDriveControllerIndex  
  INTEGER as cpqIdeLogicalDriveIndex  
  INTEGER as cpqIdeLogicalDriveRaidLevel  
  INTEGER as cpqIdeLogicalDriveCapacity  
  INTEGER as cpqIdeLogicalDriveStatus  
  INTEGER as cpqIdeLogicalDriveCondition  
  OCTET STRING as cpqIdeLogicalDriveDiskIds  
  INTEGER as cpqIdeLogicalDriveStripeSize  
  OCTET STRING as cpqIdeLogicalDriveSpareIds  
  INTEGER as cpqIdeLogicalDriveRebuildingDisk  
  DisplayString as cpqIdeLogicalDriveOsName