CTRON-SFPS-PORT-MIB

File: CTRON-SFPS-PORT-MIB.mib (40055 bytes)

Imported modules

RFC-1212 RFC1213-MIB RFC1155-SMI
CTRON-SFPS-INCLUDE-MIB

Imported symbols

OBJECT-TYPE DisplayString Counter
TimeTicks Gauge sfpsPortConfig
sfpsPortStats sfpsPortAttributeTable sfpsPortAttributeAPI

Defined Objects

sfpsInPortConfigTable 1.3.6.1.4.1.52.4.2.4.2.1.2.1.1
This table contains the configuration information of each configured inbound SFPS switch port. If SFPS is not configured on a port, than an entry will not exist.
OBJECT-TYPE    
  SEQUENCE OF  
    SfpsInPortConfigEntry

sfpsInPortConfigEntry 1.3.6.1.4.1.52.4.2.4.2.1.2.1.1.1
Each entry specifies the SFPS configuration for the SFPS inbound switch port for which the entry exists.
OBJECT-TYPE    
  SfpsInPortConfigEntry  

sfpsInPortConfigPort 1.3.6.1.4.1.52.4.2.4.2.1.2.1.1.1.1
The primary index to the SFPS in port table. This identifies the inbound SFPS switch port for which the entry exists.
OBJECT-TYPE    
  SfpsSwitchPort  

sfpsInPortConfigAdminStatus 1.3.6.1.4.1.52.4.2.4.2.1.2.1.1.1.2
Sets the administrative state of the SFPS inbound switch port for which the entry exists.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), loopback(4)  

sfpsInPortConfigOperStatus 1.3.6.1.4.1.52.4.2.4.2.1.2.1.1.1.3
Indicates the current operating condition of the SFPS on the inbound switch port for which this entry exists.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), pending-disable(4), pending-enable(5), invalid-config(6), testing(7)  

sfpsInPortConfigOperTime 1.3.6.1.4.1.52.4.2.4.2.1.2.1.1.1.4
Indicates the elapsed time, in hundredths of a second, that sfpsInPortOperStatus has been in its current operational state on the SFPS inbound switch port for which this entry exists.
OBJECT-TYPE    
  TimeTicks  

sfpsInPortConfigType 1.3.6.1.4.1.52.4.2.4.2.1.2.1.1.1.5
Sets the type of port access attribute for the inbound SFPS port for which the entry exists. Access ports allow single user or shared access and perform statisics and control; network ports are equivalent to trunk ports with no access control; host management port indicates the (virtual) port to which the (internal) management agent is attached; host control port indicates the port to redirect non-management packets.
OBJECT-TYPE    
  INTEGER other(1), access-port(2), network-port(3), host-mgmt-port(4), host-ctl-port(5), unknown(6), going-to-access(7), hybrid-port(8), stand-by(9), network-only(10), accessOnly(11), raPrimary(12), uplink(13), fclStandby(14), loopStandby(15), raStandby(16), flood(17), uplinkFlood(18), downlinkFlood(19), unknown-ra-standby(20)  

sfpsInPortConfigReservedBW 1.3.6.1.4.1.52.4.2.4.2.1.2.1.1.1.6
Sets the amount of Bandwidth that is reserved for the inbound SFPS port for which this entry exists. This bandwidth is set aside for this port and may be given to another port if unused.
OBJECT-TYPE    
  INTEGER  

sfpsInPortConfigAllocBW 1.3.6.1.4.1.52.4.2.4.2.1.2.1.1.1.7
Sets the amount of Bandwidth that is allocated for the inbound SFPS port for which this entry exists. This bandwidth may be less than the reserved bandwidth.
OBJECT-TYPE    
  INTEGER  

sfpsInPortConfigQoS 1.3.6.1.4.1.52.4.2.4.2.1.2.1.1.1.8
Sets the desired QoS service class for the inbound SFPS port for which this entry exists.
OBJECT-TYPE    
  INTEGER  

sfpsInPortConfigQSize 1.3.6.1.4.1.52.4.2.4.2.1.2.1.1.1.9
Indicates the maximum inbound queue size for this port. Size is indicated in packets (packet descriptors).
OBJECT-TYPE    
  INTEGER  

sfpsInPortConfigQLen 1.3.6.1.4.1.52.4.2.4.2.1.2.1.1.1.10
Indicates the actual inbound queue size for this port. Size is indicated in packets (packet descriptors). This is a transient value that reflects the current depth of queue.
OBJECT-TYPE    
  Gauge  

sfpsInPortConfigSwitchId 1.3.6.1.4.1.52.4.2.4.2.1.2.1.1.1.11
This entry is the id of the port.
OBJECT-TYPE    
  OCTET STRING  

sfpsInPortConfigMediaType 1.3.6.1.4.1.52.4.2.4.2.1.2.1.1.1.12
OBJECT-TYPE    
  INTEGER ethernet(1), fddi(2), atm-lec(3), token-ring(4), wan(5), inb(6), hcp(7), hdp(8), atm-svc(9), atm-pvc(10), unknown(11), atm-forum-lec(12), atm-forum-pvc(13), atm-forum-svc(14)  

sfpsInPortConfigFrontPanelPort 1.3.6.1.4.1.52.4.2.4.2.1.2.1.1.1.13
This represents the front panel physical port number
OBJECT-TYPE    
  SfpsSwitchPort  

sfpsInPortConfigLinkStatus 1.3.6.1.4.1.52.4.2.4.2.1.2.1.1.1.14
The link status of this port.
OBJECT-TYPE    
  INTEGER other(1), linkUp(2), linkDown(3), link-N-A(4)  

sfpsInPortConfigLinkStateAge 1.3.6.1.4.1.52.4.2.4.2.1.2.1.1.1.15
Number of time ticks that link has been in this state.
OBJECT-TYPE    
  TimeTicks  

sfpsInPortConfigRouterPort 1.3.6.1.4.1.52.4.2.4.2.1.2.1.1.1.16
Specifies whether this port is a router port.
OBJECT-TYPE    
  INTEGER other(1), router-port(2), no-router(3)  

sfpsInPortConfigSlotNumber 1.3.6.1.4.1.52.4.2.4.2.1.2.1.1.1.17
Slot number in the chassis.
OBJECT-TYPE    
  INTEGER  

sfpsInPortConfigMib2PortId 1.3.6.1.4.1.52.4.2.4.2.1.2.1.1.1.18
Mib2 Port id
OBJECT-TYPE    
  INTEGER  

sfpsInPortConfigTopoAgent 1.3.6.1.4.1.52.4.2.4.2.1.2.1.1.1.19
Topology Agent
OBJECT-TYPE    
  DisplayString  

sfpsInPortConfigLayer3Learning 1.3.6.1.4.1.52.4.2.4.2.1.2.1.1.1.22
Topology Agent
OBJECT-TYPE    
  INTEGER other(1), enabled(2), disabled(3)  

sfpsOutPortConfigTable 1.3.6.1.4.1.52.4.2.4.2.1.2.1.2
This table contains the configuration information of each configured outbound SFPS switch port. If SFPS is not configured on a port, than an entry will not exist.
OBJECT-TYPE    
  SEQUENCE OF  
    SfpsOutPortConfigEntry

sfpsOutPortConfigEntry 1.3.6.1.4.1.52.4.2.4.2.1.2.1.2.1
Each entry specifies the SFPS configuration for the SFPS outbound switch port for which the entry exists.
OBJECT-TYPE    
  SfpsOutPortConfigEntry  

sfpsOutPortConfigPort 1.3.6.1.4.1.52.4.2.4.2.1.2.1.2.1.1
The primary index to the SFPS in port table. This identifies the outbound SFPS switch port for which the entry exists.
OBJECT-TYPE    
  SfpsSwitchPort  

sfpsOutPortConfigAdminStatus 1.3.6.1.4.1.52.4.2.4.2.1.2.1.2.1.2
Sets the administrative state of the SFPS outbound switch port for which the entry exists.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), loopback(4)  

sfpsOutPortConfigOperStatus 1.3.6.1.4.1.52.4.2.4.2.1.2.1.2.1.3
Indicates the current operating condition of the SFPS on the outbound switch port for which this entry exists.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), pending-disable(4), pending-enable(5), invalid-config(6), testing(7)  

sfpsOutPortConfigOperTime 1.3.6.1.4.1.52.4.2.4.2.1.2.1.2.1.4
Indicates the elapsed time, in hundredths of a second, that sfpsOutPortOperStatus has been in its current operational state on the SFPS outbound switch port for which this entry exists.
OBJECT-TYPE    
  TimeTicks  

sfpsOutPortConfigType 1.3.6.1.4.1.52.4.2.4.2.1.2.1.2.1.5
Sets the type of port access attribute for the outbound SFPS port for which the entry exists. Access ports allow single user or shared access and perform statisics and control; network ports are equivalent to trunk ports with no access control; host management port indicates the (virtual) port to which the (internal) management agent is attached; host control port indicates the port to redirect non-management packets.
OBJECT-TYPE    
  INTEGER other(1), access-port(2), network-port(3), host-mgmt-port(4), host-ctl-port(5), unknown(6), going-to-access(7), hybrid-port(8), stand-by(9), network-only(10), accessOnly(11), raPrimary(12), standbyFCLConflict(13), standbyLoopedPort(14), standbyVersionConflict(15), standbyRANonPrimary(16), flood(17), uplinkFlood(18), downlinkFlood(19), unknown-ra-standby(20)  

sfpsOutPortConfigReservedBW 1.3.6.1.4.1.52.4.2.4.2.1.2.1.2.1.6
Sets the amount of Bandwidth that is reserved for the outbound SFPS port for which this entry exists. This bandwidth is set aside for this port and may be given to another port if unused.
OBJECT-TYPE    
  INTEGER  

sfpsOutPortConfigAllocBW 1.3.6.1.4.1.52.4.2.4.2.1.2.1.2.1.7
Sets the amount of Bandwidth that is allocated for the outbound SFPS port for which this entry exists. This bandwidth may be less than the reserved bandwidth.
OBJECT-TYPE    
  INTEGER  

sfpsOutPortConfigQoS 1.3.6.1.4.1.52.4.2.4.2.1.2.1.2.1.8
Sets the desired QoS service class for the outbound SFPS port for which this entry exists.
OBJECT-TYPE    
  INTEGER  

sfpsOutPortConfigQSize 1.3.6.1.4.1.52.4.2.4.2.1.2.1.2.1.9
Indicates the maximum outbound queue size for this port. Size is indicated in packets (packet descriptors).
OBJECT-TYPE    
  INTEGER  

sfpsOutPortConfigQLen 1.3.6.1.4.1.52.4.2.4.2.1.2.1.2.1.10
Indicates the actual outbound queue size for this port. Size is indicated in packets (packet descriptors). This is a transient value that reflects the current depth of queue.
OBJECT-TYPE    
  Gauge  

sfpsOutPortConfigSwitchId 1.3.6.1.4.1.52.4.2.4.2.1.2.1.2.1.11
This entry is id of the port.
OBJECT-TYPE    
  OCTET STRING  

sfpsOutPortConfigMediaType 1.3.6.1.4.1.52.4.2.4.2.1.2.1.2.1.12
OBJECT-TYPE    
  INTEGER ethernet(1), fddi(2), atm-lec(3), token-ring(4), wan(5), inb(6), hcp(7), hdp(8), atm-encap(9), atm-pvc(10), unknown(11), atm-forum-lec(12), atm-forum-pvc(13), atm-forum-svc(14)  

sfpsOutPortConfigFrontPanelPort 1.3.6.1.4.1.52.4.2.4.2.1.2.1.2.1.13
OBJECT-TYPE    
  SfpsSwitchPort  

sfpsOutPortConfigLinkStatus 1.3.6.1.4.1.52.4.2.4.2.1.2.1.2.1.14
The link status of this port.
OBJECT-TYPE    
  INTEGER other(1), linkUp(2), linkDown(3), linkNA(4)  

sfpsOutPortConfigLinkStateAge 1.3.6.1.4.1.52.4.2.4.2.1.2.1.2.1.15
Number of time ticks that link has been in this state.
OBJECT-TYPE    
  TimeTicks  

sfpsOutPortConfigRouterPort 1.3.6.1.4.1.52.4.2.4.2.1.2.1.2.1.16
Specifies whether this port is a router port.
OBJECT-TYPE    
  INTEGER other(1), router-port(2), no-router(3)  

sfpsOutPortConfigSlotNumber 1.3.6.1.4.1.52.4.2.4.2.1.2.1.2.1.17
Slot number in the chassis.
OBJECT-TYPE    
  INTEGER  

sfpsOutPortConfigMib2PortId 1.3.6.1.4.1.52.4.2.4.2.1.2.1.2.1.18
Mib2 Port id
OBJECT-TYPE    
  INTEGER  

sfpsPortAttributePort 1.3.6.1.4.1.52.4.2.4.2.1.2.1.9.1.1
OBJECT-TYPE    
  INTEGER  

sfpsPortAttributeAttributes 1.3.6.1.4.1.52.4.2.4.2.1.2.1.9.1.2
OBJECT-TYPE    
  HexInteger  

sfpsPortAttributeLearnSelfArp 1.3.6.1.4.1.52.4.2.4.2.1.2.1.9.1.3
OBJECT-TYPE    
  INTEGER off(2), on(1)  

sfpsPortAttributeAPIVerb 1.3.6.1.4.1.52.4.2.4.2.1.2.1.9.2.1
OBJECT-TYPE    
  INTEGER other(1), resetAll(2), resetPort(3), enablePortAttr(4), disablePortAttr(5)  

sfpsPortAttributeAPIPort 1.3.6.1.4.1.52.4.2.4.2.1.2.1.9.2.2
OBJECT-TYPE    
  INTEGER  

sfpsPortAttributeAPIAttribute 1.3.6.1.4.1.52.4.2.4.2.1.2.1.9.2.3
OBJECT-TYPE    
  INTEGER none(2), learnSelfArp(1)  

sfpsInPortStatsTable 1.3.6.1.4.1.52.4.2.4.2.1.2.2.1
This table contains the packet and byte counters for each inbound SFPS switch port.
OBJECT-TYPE    
  SEQUENCE OF  
    SfpsInPortStatsEntry

sfpsInPortStatsEntry 1.3.6.1.4.1.52.4.2.4.2.1.2.2.1.1
Specifies the SFPS packet and byte counters for the inbound SFPS switch port for which this entry exists.
OBJECT-TYPE    
  SfpsInPortStatsEntry  

sfpsInPortStatsPort 1.3.6.1.4.1.52.4.2.4.2.1.2.2.1.1.1
The primary index to the SFPS port table. This identifies the SFPS inbound switch port for which the entry exists.
OBJECT-TYPE    
  SfpsSwitchPort  

sfpsInPortStatsAdminStatus 1.3.6.1.4.1.52.4.2.4.2.1.2.2.1.1.2
Sets the administrative state of the SFPS packet and byte counters on the inbound SFPS switch port for which this entry exists.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

sfpsInPortStatsReset 1.3.6.1.4.1.52.4.2.4.2.1.2.2.1.1.3
Resets the SFPS packet and byte counters on the inbound SFPS switch port for which this entry exists.
OBJECT-TYPE    
  INTEGER other(1), reset(2)  

sfpsInPortStatsOperTime 1.3.6.1.4.1.52.4.2.4.2.1.2.2.1.1.4
Indicates the amount of time (# of time ticks) that the port-specific SFPS packet and byte counters have been active on the inbound SFPS switch port for which this entry exists.
OBJECT-TYPE    
  TimeTicks  

sfpsInPortStatsPkts 1.3.6.1.4.1.52.4.2.4.2.1.2.2.1.1.5
Indicates the total number of SFPS packets that have been received, during sfpsInPortStatsOpertime, on the inbound SFPS switch port for which this entry exists.
OBJECT-TYPE    
  Counter  

sfpsInPortStatsDiscardPkts 1.3.6.1.4.1.52.4.2.4.2.1.2.2.1.1.6
Indicates the total number of SFPS packets that have been discarded (dropped), during sfpsInPortStatsOpertime, on the inbound SFPS switch port for which this entry exists
OBJECT-TYPE    
  Counter  

sfpsInPortStatsBytes 1.3.6.1.4.1.52.4.2.4.2.1.2.2.1.1.7
Indicates the total number of SFPS bytes that have been received, during sfpsInPortStatsOperTime, on the inbound SFPS switch port for which the entry exists.
OBJECT-TYPE    
  Counter  

sfpsInPortStatsDiscardBytes 1.3.6.1.4.1.52.4.2.4.2.1.2.2.1.1.8
Indicates the total number of bytes in the SFPS packets that have been discarded (dropped), during sfpsInPortStatsOperTime, on the inbound SFPS switch port for which the entry exists.
OBJECT-TYPE    
  Counter  

sfpsInPortStatsQOverflows 1.3.6.1.4.1.52.4.2.4.2.1.2.2.1.1.9
Indicates the total number of queue overflow conditions have been experienced for the inbound SFPS switch port for which the entry exists.
OBJECT-TYPE    
  Counter  

sfpsInPortStatsLinkUps 1.3.6.1.4.1.52.4.2.4.2.1.2.2.1.1.10
The number of link ups that this port has seen.
OBJECT-TYPE    
  Counter  

sfpsInPortStatsLinkDowns 1.3.6.1.4.1.52.4.2.4.2.1.2.2.1.1.11
The number of link downs that this port has seen.
OBJECT-TYPE    
  Counter  

sfpsOutPortStatsTable 1.3.6.1.4.1.52.4.2.4.2.1.2.2.2
This table contains the packet and byte counters for each outbound SFPS switch port.
OBJECT-TYPE    
  SEQUENCE OF  
    SfpsOutPortStatsEntry

sfpsOutPortStatsEntry 1.3.6.1.4.1.52.4.2.4.2.1.2.2.2.1
Specifies the SFPS packet and byte counters for the outbound SFPS switch port for which this entry exists.
OBJECT-TYPE    
  SfpsOutPortStatsEntry  

sfpsOutPortStatsPort 1.3.6.1.4.1.52.4.2.4.2.1.2.2.2.1.1
The primary index to the SFPS port table. This identifies the SFPS outbound switch port for which the entry exists.
OBJECT-TYPE    
  SfpsSwitchPort  

sfpsOutPortStatsAdminStatus 1.3.6.1.4.1.52.4.2.4.2.1.2.2.2.1.2
Sets the administrative state of the SFPS packet and byte counters on the outbound SFPS switch port for which this entry exists.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

sfpsOutPortStatsReset 1.3.6.1.4.1.52.4.2.4.2.1.2.2.2.1.3
Resets the SFPS packet and byte counters on the outbound SFPS switch port for which this entry exists.
OBJECT-TYPE    
  INTEGER other(1), reset(2)  

sfpsOutPortStatsOperTime 1.3.6.1.4.1.52.4.2.4.2.1.2.2.2.1.4
Indicates the amount of time (# of time ticks) that the port-specific SFPS packet and byte counters have been active on the outbound SFPS switch port for which this entry exists.
OBJECT-TYPE    
  TimeTicks  

sfpsOutPortStatsPkts 1.3.6.1.4.1.52.4.2.4.2.1.2.2.2.1.5
Indicates the total number of SFPS packets that have been received, during sfpsOutPortStatsOpertime, on the outbound SFPS switch port for which this entry exists.
OBJECT-TYPE    
  Counter  

sfpsOutPortStatsDiscardPkts 1.3.6.1.4.1.52.4.2.4.2.1.2.2.2.1.6
Indicates the total number of SFPS packets that have been discarded (dropped), during sfpsOutPortStatsOpertime, on the outbound SFPS switch port for which this entry exists
OBJECT-TYPE    
  Counter  

sfpsOutPortStatsBytes 1.3.6.1.4.1.52.4.2.4.2.1.2.2.2.1.7
Indicates the total number of SFPS bytes that have been received, during sfpsOutPortStatsOperTime, on the outbound SFPS switch port for which the entry exists.
OBJECT-TYPE    
  Counter  

sfpsOutPortStatsDiscardBytes 1.3.6.1.4.1.52.4.2.4.2.1.2.2.2.1.8
Indicates the total number of bytes in the SFPS packets that have been discarded (dropped), during sfpsOutPortStatsOperTime, on the outbound SFPS switch port for which the entry exists.
OBJECT-TYPE    
  Counter  

sfpsOutPortStatsQOverflows 1.3.6.1.4.1.52.4.2.4.2.1.2.2.2.1.9
Indicates the total number of queue overflow conditions have been experienced for the outbound SFPS switch port for which the entry exists.
OBJECT-TYPE    
  Counter  

sfpsOutPortStatsLinkUps 1.3.6.1.4.1.52.4.2.4.2.1.2.2.2.1.10
The number of link ups that this port has seen.
OBJECT-TYPE    
  Counter  

sfpsOutPortStatsLinkDowns 1.3.6.1.4.1.52.4.2.4.2.1.2.2.2.1.11
The number of link downs that this port has seen.
OBJECT-TYPE    
  Counter  

Defined Objects

SfpsSwitchPort  
INTEGER    

HexInteger  
INTEGER    

SfpsInPortConfigEntry  
SEQUENCE    
  SfpsSwitchPort as sfpsInPortConfigPort  
  INTEGER as sfpsInPortConfigAdminStatus  
  INTEGER as sfpsInPortConfigOperStatus  
  TimeTicks as sfpsInPortConfigOperTime  
  INTEGER as sfpsInPortConfigType  
  INTEGER as sfpsInPortConfigReservedBW  
  INTEGER as sfpsInPortConfigAllocBW  
  INTEGER as sfpsInPortConfigQoS  
  INTEGER as sfpsInPortConfigQSize  
  Gauge as sfpsInPortConfigQLen  
  OCTET STRING as sfpsInPortConfigSwitchId  
  INTEGER as sfpsInPortConfigMediaType  
  SfpsSwitchPort as sfpsInPortConfigFrontPanelPort  
  INTEGER as sfpsInPortConfigLinkStatus  
  TimeTicks as sfpsInPortConfigLinkStateAge  
  INTEGER as sfpsInPortConfigRouterPort  
  INTEGER as sfpsInPortConfigSlotNumber  
  INTEGER as sfpsInPortConfigMib2PortId  
  DisplayString as sfpsInPortConfigTopoAgent  
  INTEGER as sfpsInPortConfigLayer3Learning  

SfpsOutPortConfigEntry  
SEQUENCE    
  SfpsSwitchPort as sfpsOutPortConfigPort  
  INTEGER as sfpsOutPortConfigAdminStatus  
  INTEGER as sfpsOutPortConfigOperStatus  
  TimeTicks as sfpsOutPortConfigOperTime  
  INTEGER as sfpsOutPortConfigType  
  INTEGER as sfpsOutPortConfigReservedBW  
  INTEGER as sfpsOutPortConfigAllocBW  
  INTEGER as sfpsOutPortConfigQoS  
  INTEGER as sfpsOutPortConfigQSize  
  Gauge as sfpsOutPortConfigQLen  
  OCTET STRING as sfpsOutPortConfigSwitchId  
  INTEGER as sfpsOutPortConfigMediaType  
  SfpsSwitchPort as sfpsOutPortConfigFrontPanelPort  
  INTEGER as sfpsOutPortConfigLinkStatus  
  TimeTicks as sfpsOutPortConfigLinkStateAge  
  INTEGER as sfpsOutPortConfigRouterPort  
  INTEGER as sfpsOutPortConfigSlotNumber  
  INTEGER as sfpsOutPortConfigMib2PortId  

SfpsInPortStatsEntry  
SEQUENCE    
  SfpsSwitchPort as sfpsInPortStatsPort  
  INTEGER as sfpsInPortStatsAdminStatus  
  INTEGER as sfpsInPortStatsReset  
  TimeTicks as sfpsInPortStatsOperTime  
  Counter as sfpsInPortStatsPkts  
  Counter as sfpsInPortStatsDiscardPkts  
  Counter as sfpsInPortStatsBytes  
  Counter as sfpsInPortStatsDiscardBytes  
  Counter as sfpsInPortStatsQOverflows  
  Counter as sfpsInPortStatsLinkUps  
  Counter as sfpsInPortStatsLinkDowns  

SfpsOutPortStatsEntry  
SEQUENCE    
  SfpsSwitchPort as sfpsOutPortStatsPort  
  INTEGER as sfpsOutPortStatsAdminStatus  
  INTEGER as sfpsOutPortStatsReset  
  TimeTicks as sfpsOutPortStatsOperTime  
  Counter as sfpsOutPortStatsPkts  
  Counter as sfpsOutPortStatsDiscardPkts  
  Counter as sfpsOutPortStatsBytes  
  Counter as sfpsOutPortStatsDiscardBytes  
  Counter as sfpsOutPortStatsQOverflows  
  Counter as sfpsOutPortStatsLinkUps  
  Counter as sfpsOutPortStatsLinkDowns