CXAsyncIo-MIB

File: CXAsyncIo-MIB.mib (50877 bytes)

Imported modules

RFC1155-SMI RFC-1212 RFC-1215
CXProduct-SMI

Imported symbols

Counter OBJECT-TYPE TRAP-TYPE
cxAsyncIo Alias

Defined Objects

asioSapOprTable 1.3.6.1.4.1.495.2.1.6.44.1
Contains configuration information about each Async driver SAP (service access point) and its associated hardware port.
OBJECT-TYPE    
  SEQUENCE OF  
    AsioSapOprEntry

asioPortStatusChange 1.3.6.1.4.1.495.2.1.6.44.1
Indicates that the associated hardware port has changed state. It has toggled between any of the states as defined in object asyStatOprPortState.
TRAP-TYPE    
  asioSapOprNumber  
  asioStatOprPortState  

asioSapOprEntry 1.3.6.1.4.1.495.2.1.6.44.1.1
Contains configuration information for a specific Async driver SAP (service access point) and its associated hardware port.
OBJECT-TYPE    
  AsioSapOprEntry  

asioSapOprNumber 1.3.6.1.4.1.495.2.1.6.44.1.1.1
Indicates the table row containing configuration or monitoring objects for a SAP (service access point) associated with the slot and port for this card. Range of Values: 11 - 71 Note: First digit indicates the slot and the second digit indicates the port. Default Value: none
OBJECT-TYPE    
  INTEGER  

asioSapOprAlias 1.3.6.1.4.1.495.2.1.6.44.1.1.2
Determines the name which uniquely identifies the SAP (service access point). Range of Values: 1 to 16 alphanumeric characters starting with an alpha character Default Value: none Configuration Changed: Administrative
OBJECT-TYPE    
  Alias  

asioSapOprPortSpeed 1.3.6.1.4.1.495.2.1.6.44.1.1.3
Defines the input and output speed, in bits per second, for the associated hardware port. Any value between 50 and 115200 will be accepted. Note: 134.5 bit/s is the minimum speed supported on ports in slots 5, 6 and 7 when the Data Expansion Module is installed. Default Value: 9600 bit/s
OBJECT-TYPE    
  INTEGER 50..115200  

asioSapOprPortCharacterSize 1.3.6.1.4.1.495.2.1.6.44.1.1.5
Defines the character size, in number of bits, to be used on the associated hardware port. Options: 5,6, 7 or 8 Note: This value does not include the start, stop or parity bits.
OBJECT-TYPE    
  INTEGER 5..8  

asioSapOprPortStopBits 1.3.6.1.4.1.495.2.1.6.44.1.1.6
Defines the number of stop bits to be used on the associated hardware port. Options: one (1 bit) one-point-five (1.5 bits) two (2 bits) Default Value: 1 bit
OBJECT-TYPE    
  INTEGER one(1), one-point-five(2), two(3)  

asioSapOprPortBreakLength 1.3.6.1.4.1.495.2.1.6.44.1.1.7
Defines the number of break characters to be transmitted on the line when a reset is requested by the upper layer. A break is an all-zeroes character without a stop bit(s). Range of Values: 0 - 65535 Default Value: 10
OBJECT-TYPE    
  INTEGER 0..65535  

asioSapOprPortMaxQueueLength 1.3.6.1.4.1.495.2.1.6.44.1.1.8
Defines the maximum transmitter queue length, in number of buffers. If more data requests are received from the upper layer after the queue has reached its maximum value, the data is discarded and the object asyStatOprTxSysCongestionDiscards is incremented. You must be careful when updating this object dynamically because queued data can be lost if the size of the transmitter queue is decreased. Range of Values: 1 - 100 Default Value: 50 Configuration Changed: Operative only
OBJECT-TYPE    
  INTEGER 1..100  

asioSapOprPortQueueUpperThreshold 1.3.6.1.4.1.495.2.1.6.44.1.1.9
Defines the queue length, in number of buffers, after which the Async driver starts flow controlling the upper layer. After the queue has reached this length, the Async driver will queue more data requests on the transmit queue up to the length specified in object asySapOprPortMaxQueueLength. Data is discarded above that length. The value for this object should always be less than the value of object asySapOprPortMaxQueueLength Range of Values: 1 - 100 Default Value: 45 Configuration Changed: Operative only
OBJECT-TYPE    
  INTEGER 1..100  

asioSapOprPortQueueLowerThreshold 1.3.6.1.4.1.495.2.1.6.44.1.1.10
Defines the queue length, in number of buffers, after which the Async driver stops flow controlling the upper layer. The value for this object should always be less than or equal to the value of object asySapOprPortQueueUpperThreshold. Range of Values: 1 - 100 Default Value: 15 Configuration Changed: Operative only
OBJECT-TYPE    
  INTEGER 1..100  

asioSapOprPortSignalDownTimer 1.3.6.1.4.1.495.2.1.6.44.1.1.11
Defines the length of time, in seconds, after which the Async port will drop its signals when it has received a disconnect request from the upper layer. Range of Values: 0 - 255 Default Value: 3
OBJECT-TYPE    
  INTEGER 0..255  

asioSapOprPortMaxTimeDelay 1.3.6.1.4.1.495.2.1.6.44.1.1.12
Defines the maximum time, in milliseconds, the port must wait before processing received characters. Range of Values: 1 - 5 Default Value: 5
OBJECT-TYPE    
  INTEGER 1..5  

asioSapOprPortMaxInterruptCharacters 1.3.6.1.4.1.495.2.1.6.44.1.1.13
Obsolete.
OBJECT-TYPE    
  INTEGER 5..40  

asioSapOprPortSignalSamplingPeriod 1.3.6.1.4.1.495.2.1.6.44.1.1.20
Determines the sampling period, in 100 millisecond increments, that the associated hardware port uses to sample detectable signals. Range of Values: 3 - 100 Default Value: 5 Configuration Changed: Operative only
OBJECT-TYPE    
  INTEGER 3..100  

asioSapOprPortDcdDtrSignalSamples 1.3.6.1.4.1.495.2.1.6.44.1.1.21
Defines the number of samples of object asySapPortSignalSamplingPeriod that the associated hardware port must detect before validating the DCD (Data Carrier Detect) signals if the port is physically strapped as a DTE, or DTR (Data Terminal Ready) signals if the port is strapped as a DCE. Range of Values: 1 - 30 Default Value: 3 Configuration Changed: Operative only
OBJECT-TYPE    
  INTEGER 1..30  

asioSapOprPortCtsRtsSignalSamples 1.3.6.1.4.1.495.2.1.6.44.1.1.22
Defines the number of samples of object asySapPortSignalSamplingPeriod that the associated hardware port must detect before validating the CTS (Clear To Send) signals if the port is physically strapped as a DTE, or RTS (Request To Send) signals if the port is strapped as a DCE. Range of Values: 1 - 30 Default Value: 3 Configuration Changed: Operative only
OBJECT-TYPE    
  INTEGER 1..30  

asioSapOprPortDsrDrsSignalSamples 1.3.6.1.4.1.495.2.1.6.44.1.1.23
Defines the number of samples of object asySapPortSignalSamplingPeriod that the associated hardware port must detect before validating the DRS (Data Rate Selector) signals if the port is physically strapped as a DTE, or DSR (Data Set Ready) signals if the port is strapped as a DCE. Range of Values: 1 - 30 Default Value: 3 Configuration Changed: Operative only
OBJECT-TYPE    
  INTEGER 1..30  

asioSapOprPortTmLlSignalSamples 1.3.6.1.4.1.495.2.1.6.44.1.1.24
Defines the number of samples of object asySapPortSignalSamplingPeriod that the associated hardware port must detect before validating the TM (Test Mode) signals if the port is physically strapped as a DTE, or LL (Local Loopback) signals if the port is strapped as a DCE. Range of Values: 1 - 30 Default Value: 3 Configuration Changed: Operative only
OBJECT-TYPE    
  INTEGER 1..30  

asioSapOprPortRiRlSignalSamples 1.3.6.1.4.1.495.2.1.6.44.1.1.25
Defines the number of samples of object asySapPortSignalSamplingPeriod that the associated hardware port must detect before validating the RI (Ring Indicator)signals if the port is physically strapped as a DTE, RL (Remote Loopback) signals if the port is strapped as a DCE. Range of Values: 1 - 30 Default Value: 3 Configuration Changed: Operative only
OBJECT-TYPE    
  INTEGER 1..30  

asioSapOprPortStatisticsTimer 1.3.6.1.4.1.495.2.1.6.44.1.1.26
Determines the period of time, in seconds, that is used to measure Async driver performance and collect statistics. Range of Values: 0 - 60. Default Value: 0 (Performance statistics are not measured)
OBJECT-TYPE    
  INTEGER 0..60  

asioSapOprPortCarrierAction 1.3.6.1.4.1.495.2.1.6.44.1.1.27
Determines whether or not this SAP (service access point) will inform the associated upper layer SAP that service is no longer available because its associated hardware port has detected a loss of DCD (Data Carrier Detect) if the port is physically strapped as a DTE, or a loss of DTR (Data Terminal Ready) if the port is physically strapped as a DCE. Options: disabled (1) enabled (2) Default Value: disabled Configuration Changed: Operative only
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

asioOprPortTrap 1.3.6.1.4.1.495.2.1.6.44.1.1.30
Indicates whether or not this SAP (service access point) produces the object asyPortStatusChange trap. Options: disabled (1) enabled (2) Default Value: disabled Configuration Changed: Operative only
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

asioOprControlLine 1.3.6.1.4.1.495.2.1.6.44.1.1.34
Controls the state of the hardware port associated with the specified SAP (service access point). Options: forceDown (1) forceUp (2) forceReset (3) Configuration Changed: Operative only
OBJECT-TYPE    
  INTEGER forceDown(1), forceUp(2), forceReset(3)  

asioOprControlStats 1.3.6.1.4.1.495.2.1.6.44.1.1.35
Controls the handling of statistics collected at the associated hardware port. Option: clearSAPStats (1) Configuration Changed: Operative only
OBJECT-TYPE    
  INTEGER clearSapStats(1)  

asioStatOprPortType 1.3.6.1.4.1.495.2.1.6.44.1.1.38
Identifies the hardware strapping used at the associated hardware port. Options: unknown (1) dte (2) dce (3)
OBJECT-TYPE    
  INTEGER unknown(1), dte(2), dce(3)  

asioStatOprPortInterfaceType 1.3.6.1.4.1.495.2.1.6.44.1.1.39
Identifies the type of hardware interface needed for the associated hardware port. Options: unknown (1) rs232d
OBJECT-TYPE    
  INTEGER unknown(1), rs232d(2)  

asioStatOprPortState 1.3.6.1.4.1.495.2.1.6.44.1.1.40
Indicates the state of the associated hardware port. Options: portUp (1) portDown (2) portShutDown (3) portDownBadConfiguration (4) portOutOfOrder (5)
OBJECT-TYPE    
  INTEGER portUp(1), portDown(2), portShutDown(3), portDownBadConfiguration(4), portOutOfOrder(5)  

asioStatOprDCDState 1.3.6.1.4.1.495.2.1.6.44.1.1.45
Indicates the current state (active- high or active-low) of the DCD (Data Carrier Detect) signal at the associated hardware port. Options: unknown (1) inactive (2) active (3)
OBJECT-TYPE    
  INTEGER unknown(1), inactive(2), active(3)  

asioStatOprDTRState 1.3.6.1.4.1.495.2.1.6.44.1.1.46
Indicates the current state (active- high or active-low) of the DTR (Data Terminal Ready) signal at the associated hardware port. Options: unknown (1) inactive (2) active (3)
OBJECT-TYPE    
  INTEGER unknown(1), inactive(2), active(3)  

asioStatOprRTSState 1.3.6.1.4.1.495.2.1.6.44.1.1.47
Indicates the current state (active- high or active-low) of the RTS (Request To Send) signal at the associated hardware port. Options: unknown (1) inactive (2) active (3)
OBJECT-TYPE    
  INTEGER unknown(1), inactive(2), active(3)  

asioStatOprCTSState 1.3.6.1.4.1.495.2.1.6.44.1.1.48
Indicates the current state (active- high or active-low) of the CTS (Clear To Send) signal at the associated hardware port. Options: unknown (1) inactive (2) active (3)
OBJECT-TYPE    
  INTEGER unknown(1), inactive(2), active(3)  

asioStatOprDSRState 1.3.6.1.4.1.495.2.1.6.44.1.1.49
Indicates the current state (active- high or active-low) of the DSR (Data Set Ready) signal at the associated hardware port. Options: unknown (1) inactive (2) active (3)
OBJECT-TYPE    
  INTEGER unknown(1), inactive(2), active(3)  

asioStatOprDRSState 1.3.6.1.4.1.495.2.1.6.44.1.1.50
Indicates the current state (active- high or active-low) of the DRS (Data Rate Selection) signal at the associated hardware port. Options: unknown (1) inactive (2) active (3)
OBJECT-TYPE    
  INTEGER unknown(1), inactive(2), active(3)  

asioStatOprTMState 1.3.6.1.4.1.495.2.1.6.44.1.1.51
Indicates the current state (active- high or active-low) of the TM (Test Mode) signal at the associated hardware port. Options: unknown (1) inactive (2) active (3)
OBJECT-TYPE    
  INTEGER unknown(1), inactive(2), active(3)  

asioStatOprLLState 1.3.6.1.4.1.495.2.1.6.44.1.1.52
Indicates the current state (active- high or active-low) of the LL (Local Loopback) signal at the associated hardware port. Options: unknown (1) inactive (2) active (3)
OBJECT-TYPE    
  INTEGER unknown(1), inactive(2), active(3)  

asioStatOprRIState 1.3.6.1.4.1.495.2.1.6.44.1.1.53
Indicates the current state (active- high or active-low) of the RI (Ring Indicator) signal at the associated hardware port. Options: unknown (1) inactive (2) active (3)
OBJECT-TYPE    
  INTEGER unknown(1), inactive(2), active(3)  

asioStatOprRLState 1.3.6.1.4.1.495.2.1.6.44.1.1.54
Indicates the current state (active- high or active-low) of the RL (Remote Loopback) signal at the associated hardware port. Options: unknown (1) inactive (2) active (3)
OBJECT-TYPE    
  INTEGER unknown(1), inactive(2), active(3)  

asioStatOprTxBps 1.3.6.1.4.1.495.2.1.6.44.1.1.59
Indicates the number of bits per second that were transmitted during the sampling period entered in object asySapAdmPortStatisticsTimer.
OBJECT-TYPE    
  Counter  

asioStatOprRxBps 1.3.6.1.4.1.495.2.1.6.44.1.1.60
Indicates the number of bits per second that were received during the sampling period entered in object asySapAdmPortStatisticsTimer.
OBJECT-TYPE    
  Counter  

asioStatOprTxBpsMax 1.3.6.1.4.1.495.2.1.6.44.1.1.61
Indicates the maximum number of bits per second transmitted, since the statistics were last reset, during the sampling period entered in object asySapAdmPortStatisticsTimer.
OBJECT-TYPE    
  Counter  

asioStatOprRxBpsMax 1.3.6.1.4.1.495.2.1.6.44.1.1.62
Indicates the maximum number of bits per second received, since the statistics were last reset, during the sampling period entered in object asySapAdmPortStatisticsTimer.
OBJECT-TYPE    
  Counter  

asioStatOprTxCharacters 1.3.6.1.4.1.495.2.1.6.44.1.1.63
Indicates the number of characters transmitted from this port, since the statistics were last reset, during the sampling period entered in object asySapAdmPortStatisticsTimer.
OBJECT-TYPE    
  Counter  

asioStatOprTxBadStateDiscards 1.3.6.1.4.1.495.2.1.6.44.1.1.64
Indicates the number of characters that were discarded at this SAP (service access point) since the last power-up. The characters were discarded as a result of a frame transmission requested while the port was in an invalid state, during the sampling period entered in object asySapAdmPortStatisticsTimer.
OBJECT-TYPE    
  Counter  

asioStatOprTxResetDiscards 1.3.6.1.4.1.495.2.1.6.44.1.1.65
Indicates the number of characters that were discarded at this SAP (service access point) since the last power-up as a result of a management requested line reset during the sampling period entered in object asySapAdmPortStatisticsTimer.
OBJECT-TYPE    
  Counter  

asioStatOprTxSysCongestionDiscards 1.3.6.1.4.1.495.2.1.6.44.1.1.66
Indicates the number of characters that were discarded at this SAP (service access point) since the last power-up as a result of system congestion, during the sampling period entered in object asySapAdmPortStatisticsTimer.
OBJECT-TYPE    
  Counter  

asioStatOprRxCharacters 1.3.6.1.4.1.495.2.1.6.44.1.1.72
Indicates the number of characters that were received through this port since the statistics were last reset, during the sampling period entered in object asySapAdmPortStatisticsTimer.
OBJECT-TYPE    
  Counter  

asioStatOprRxOverrunErrorCharacters 1.3.6.1.4.1.495.2.1.6.44.1.1.73
Indicates the number of overrun error characters that were received by the associated hardware port since the last power-up, during the sampling period entered in object asySapAdmPortStatisticsTimer.
OBJECT-TYPE    
  Counter  

asioStatOprRxParityErrorCharacters 1.3.6.1.4.1.495.2.1.6.44.1.1.74
Indicates the number of parity error characters that were received by the associated hardware port since the last power-up, during the sampling period entered in object asySapAdmPortStatisticsTimer.
OBJECT-TYPE    
  Counter  

asioStatOprRxFramingErrorCharacters 1.3.6.1.4.1.495.2.1.6.44.1.1.75
Indicates the number of framing error characters that were received by the associated hardware port since the last power-up, during the sampling period entered in object asySapAdmPortStatisticsTimer.
OBJECT-TYPE    
  Counter  

asioStatOprRxNoiseErrorCharacters 1.3.6.1.4.1.495.2.1.6.44.1.1.76
Indicates the number of noise error characters that were received by the associated hardware port since the last power-up, during the sampling period entered in object asySapAdmPortStatisticsTimer.
OBJECT-TYPE    
  Counter  

asioStatOprRxBreakCharacters 1.3.6.1.4.1.495.2.1.6.44.1.1.77
Indicates the number of break characters that were received by the associated hardware port since the last power-up, during the sampling period entered in object asySapAdmPortStatisticsTimer.
OBJECT-TYPE    
  Counter  

asioStatOprRxBadStateDiscards 1.3.6.1.4.1.495.2.1.6.44.1.1.78
Indicates the number of characters that were discarded at this SAP (service access point) since the last power-up. They were discarded as a result of a frame reception while in an invalid state, during the sampling period entered in object asySapAdmPortStatisticsTimer.
OBJECT-TYPE    
  Counter  

asioStatOprRxBusyDiscards 1.3.6.1.4.1.495.2.1.6.44.1.1.79
Indicates the number of characters that were discarded at this SAP (service access point) since the last power-up. They were discarded as a result of a busy condition, during the sampling period entered in object asySapAdmPortStatisticsTimer. Note: The busy condition occurs as a result of a slow response to data reception.
OBJECT-TYPE    
  Counter  

asioStatOprPortStateChanges 1.3.6.1.4.1.495.2.1.6.44.1.1.85
Indicates the number of state transitions that have occurred at the associated hardware port since the last power-up, during the sampling period entered in object asySapAdmPortStatisticsTimer. Note: One state transition is defined as a change between any of the states defined in object asyStatOprPortState.
OBJECT-TYPE    
  Counter  

asioStatOprDCDStateChanges 1.3.6.1.4.1.495.2.1.6.44.1.1.86
Indicates the number of DCD (Data Carrier Detect) state transitions that have occurred at the associated hardware port since the last power-up, during the sampling period entered in object asySapAdmPortStatisticsTimer. Note: One state transition is defined as a change from inactive to active, or vice- versa.
OBJECT-TYPE    
  Counter  

asioStatOprDTRStateChanges 1.3.6.1.4.1.495.2.1.6.44.1.1.87
Indicates the number of DTR (Data Terminal Ready) state transitions that have occurred at the associated hardware port since the last power-up, during the sampling period entered in object asySapAdmPortStatisticsTimer. Note: One state transition is defined as a change from inactive to active, or vice- versa.
OBJECT-TYPE    
  Counter  

asioStatOprRTSStateChanges 1.3.6.1.4.1.495.2.1.6.44.1.1.88
Indicates the number of RTS (Request To Send) state transitions that have occurred at the associated hardware port since the last power-up, during the sampling period entered in object asySapAdmPortStatisticsTimer. Note: One state transition is defined as a change from inactive to active, or vice- versa.
OBJECT-TYPE    
  Counter  

asioStatOprCTSStateChanges 1.3.6.1.4.1.495.2.1.6.44.1.1.89
Indicates the number of CTS (Clear To Send) state transitions that have occurred at the associated hardware port since the last power-up, during the sampling period entered in object asySapAdmPortStatisticsTimer. Note: One state transition is defined as a change from inactive to active, or vice versa.
OBJECT-TYPE    
  Counter  

asioStatOprDSRStateChanges 1.3.6.1.4.1.495.2.1.6.44.1.1.90
Indicates the number of DSR (Data Set Ready) state transitions that have occurred at the associated hardware port since the last power-up, during the sampling period entered in object asySapAdmPortStatisticsTimer. Note: One state transition is defined as a change from inactive to active, or vice- versa.
OBJECT-TYPE    
  Counter  

asioStatOprDRSStateChanges 1.3.6.1.4.1.495.2.1.6.44.1.1.91
Indicates the number of DRS (Data Rate Selector) state transitions that have occurred at the associated hardware port since the last power-up, during the sampling period entered in object asySapAdmPortStatisticsTimer. Note: One state transition is defined as a change from inactive to active, or vice- versa.
OBJECT-TYPE    
  Counter  

asioStatOprTMStateChanges 1.3.6.1.4.1.495.2.1.6.44.1.1.92
Indicates the number of TM (Test Mode) state transitions that have occurred at the associated hardware port since the last power-up, during the sampling period entered in object asySapAdmPortStatisticsTimer. Note: One state transition is defined as a change from inactive to active, or vice- versa.
OBJECT-TYPE    
  Counter  

asioStatOprLLStateChanges 1.3.6.1.4.1.495.2.1.6.44.1.1.93
Indicates the number of LL (Local Loopback) state transitions that have occurred at the associated hardware port since the last power-up, during the sampling period entered in object asySapAdmPortStatisticsTimer. Note: One state transition is defined as a change from inactive to active, or vice- versa.
OBJECT-TYPE    
  Counter  

asioStatOprRIStateChanges 1.3.6.1.4.1.495.2.1.6.44.1.1.94
Indicates the number of RI (Ring Indicator) state transitions that have occurred at the associated hardware port since the last power-up, during the sampling period entered in object asySapAdmPortStatisticsTimer. Note: One state transition is defined as a change from inactive to active, or vice- versa.
OBJECT-TYPE    
  Counter  

asioStatOprRLStateChanges 1.3.6.1.4.1.495.2.1.6.44.1.1.95
Indicates the number of RL (Remote Loopback) state transitions that have occurred at the associated hardware port since the last power-up, during the sampling period entered in object asySapAdmPortStatisticsTimer. Note: One state transition is defined as a change from inactive to active, or vice- versa.
OBJECT-TYPE    
  Counter  

asioStatOprPortResets 1.3.6.1.4.1.495.2.1.6.44.1.1.96
Indicates the number of port resets that have occurred at the associated hardware port since the last power-up, during the sampling period entered in object asySapAdmPortStatisticsTimer.
OBJECT-TYPE    
  Counter  

asioSapAdmTable 1.3.6.1.4.1.495.2.1.6.44.2
Contains the planned configuration information for each Async driver SAP (service access point) and its associated hardware port.
OBJECT-TYPE    
  SEQUENCE OF  
    AsioSapAdmEntry

asioSapAdmEntry 1.3.6.1.4.1.495.2.1.6.44.2.1
Contains the planned configuration information for a specific Async driver SAP (service access point) and its associated hardware port.
OBJECT-TYPE    
  AsioSapAdmEntry  

asioSapAdmNumber 1.3.6.1.4.1.495.2.1.6.44.2.1.1
Indicates the table row containing configuration or monitoring objects for a SAP (service access point) associated with the slot and a port for this card. Range of Values: 11 - 71 Note: First digit indicates the slot and the second digit indicates the port. Default Value: None
OBJECT-TYPE    
  INTEGER  

asioSapAdmAlias 1.3.6.1.4.1.495.2.1.6.44.2.1.2
Determines the name which uniquely identifies the SAP (service access point). Range of Values: 1 to 16 alphanumeric characters beginning with an alpha character Default Value: none Configuration Changed: Administrative
OBJECT-TYPE    
  Alias  

asioSapAdmPortSpeed 1.3.6.1.4.1.495.2.1.6.44.2.1.3
Defines the input and output speed, in bits per second, for the associated hardware port. Any value between 50 and 115200 will be accepted. Note: 134.5 bit/s is the minimum speed supported on ports in slots 5, 6 and 7 when the Data Expansion Module is installed. Default Value: 9600 bit/s Configuration Changed: Administrative
OBJECT-TYPE    
  INTEGER 50..115200  

asioSapAdmPortCharacterSize 1.3.6.1.4.1.495.2.1.6.44.2.1.5
Defines the character size, in number of bits, to be used on the associated hardware port. Options: 5, 6, 7 or 8 Note: This value does not include the start, stop or parity bits. Default Value: 8 Configuration Changed: Administrative
OBJECT-TYPE    
  INTEGER 5..8  

asioSapAdmPortStopBits 1.3.6.1.4.1.495.2.1.6.44.2.1.6
Defines the number of stop bits to be used on the associated hardware port. Options: one (1 bit) one-point-five (1.5 bits) two (2 bits) Default Value: 1 bit Configuration Changed: Administrative
OBJECT-TYPE    
  INTEGER one(1), one-point-five(2), two(3)  

asioSapAdmPortBreakLength 1.3.6.1.4.1.495.2.1.6.44.2.1.7
Defines the number of break characters to be transmitted on the line when a reset is requested by the upper layer. A break is an all-zeroes character without a stop bit(s). Range of Values: 0 - 65535 Default Value: 3 Configuration Changed: Administrative
OBJECT-TYPE    
  INTEGER 0..65535  

asioSapAdmPortMaxQueueLength 1.3.6.1.4.1.495.2.1.6.44.2.1.8
Defines the maximum transmitter queue length, in number of buffers. If more data requests are received from the upper layer after the queue has reached its maximum value, the data is discarded and the object asyStatOprTxSysCongestionDiscards is incremented. You must be careful when updating this object dynamically because queued data can be lost if the size of the transmitter queue is decreased. Range of Values: 1 - 100 Default Value: 50 Configuration Changed: Administrative
OBJECT-TYPE    
  INTEGER 1..100  

asioSapAdmPortQueueUpperThreshold 1.3.6.1.4.1.495.2.1.6.44.2.1.9
Defines the queue length, in number of buffers, after which the Async driver starts flow controlling the upper layer. After the queue has reached this length, the Async driver will queue more data requests on the transmit queue up to the length specified in object asySapOprPortMaxQueueLength. Data is discarded above that length. The value for this object should always be less than or equal to the value of object asySapOprPortMaxQueueLength Range of Values: 1 - 100 Default Value: 45 Configuration Changed: Administrative
OBJECT-TYPE    
  INTEGER 1..100  

asioSapAdmPortQueueLowerThreshold 1.3.6.1.4.1.495.2.1.6.44.2.1.10
Defines the queue length, in number of buffers, after which the Async driver stops flow controlling the upper layer. The value for this object should always be less than or equal to the value of object asySapOprPortQueueUpperThreshold. Range of Values: 1 - 100 Default Value: 15 Configuration Changed: Administrative
OBJECT-TYPE    
  INTEGER 1..100  

asioSapAdmPortSignalDownTimer 1.3.6.1.4.1.495.2.1.6.44.2.1.11
Defines the length of time, in seconds, after which the Async port will drop its signals when it has received a disconnect request from the upper layer. Range of Values: 0 - 255 Default Value: 3 Configuration Changed: Administrative
OBJECT-TYPE    
  INTEGER 0..255  

asioSapAdmPortMaxTimeDelay 1.3.6.1.4.1.495.2.1.6.44.2.1.12
Defines the maximum time, in milliseconds, the port must wait before processing received characters. Range of Values: 1 - 5 Default Value: 5 Configuration Changed: Administrative
OBJECT-TYPE    
  INTEGER 1..5  

asioSapAdmPortMaxInterruptCharacters 1.3.6.1.4.1.495.2.1.6.44.2.1.13
Obsolete.
OBJECT-TYPE    
  INTEGER 5..40  

asioSapAdmPortSignalSamplingPeriod 1.3.6.1.4.1.495.2.1.6.44.2.1.20
Determines the sampling period, in 100 millisecond increments, that the associated hardware port uses to sample detectable signals. Range of Values: 3 - 100 Default Value: 5 Configuration Changed: Administrative
OBJECT-TYPE    
  INTEGER 3..100  

asioSapAdmPortDcdDtrSignalSamples 1.3.6.1.4.1.495.2.1.6.44.2.1.21
Defines the number of samples of object asySapPortSignalSamplingPeriod that the associated hardware port must detect before validating the DCD (Data Carrier Detect) signals if the port is physically strapped as a DTE, or DTR (Data Terminal Ready) signals if the port is strapped as a DCE. Range of Values: 1 - 30 Default Value: 3 Configuration Changed: Administrative
OBJECT-TYPE    
  INTEGER 1..30  

asioSapAdmPortCtsRtsSignalSamples 1.3.6.1.4.1.495.2.1.6.44.2.1.22
Defines the number of samples of object asySapPortSignalSamplingPeriod that the associated hardware port must detect before validating the CTS (Clear To Send) signals if the port is physically strapped as a DTE, or RTS (Request To Send) signals if the port is strapped as a DCE. Range of Values: 1 - 30 Default Value: 3 Configuration Changed: Administrative
OBJECT-TYPE    
  INTEGER 1..30  

asioSapAdmPortDsrDrsSignalSamples 1.3.6.1.4.1.495.2.1.6.44.2.1.23
Defines the number of samples of object asySapPortSignalSamplingPeriod that the associated hardware port must detect before validating the DRS (Data Rate Selector) signals if the port is physically strapped as a DTE, or DSR (Data Set Ready) signals if the port is strapped as a DCE. Range of Values: 1 - 30 Default Value: 3 Configuration Changed: Administrative
OBJECT-TYPE    
  INTEGER 1..30  

asioSapAdmPortTmLlSignalSamples 1.3.6.1.4.1.495.2.1.6.44.2.1.24
Defines the number of samples of object asySapPortSignalSamplingPeriod that the associated hardware port must detect before validating the TM (Test Mode) signals if the port is physically strapped as a DTE, or LL (Local Loopback) signals if the port is strapped as a DCE. Range of Values: 1 - 30 Default Value: 3 Configuration Changed: Administrative
OBJECT-TYPE    
  INTEGER 1..30  

asioSapAdmPortRiRlSignalSamples 1.3.6.1.4.1.495.2.1.6.44.2.1.25
Defines the number of samples of object asySapPortSignalSamplingPeriod that the associated hardware port must detect before validating the RI (Ring Indicator)signals if the port is physically strapped as a DTE, RL (Remote Loopback) signals if the port is strapped as a DCE. Range of Values: 1 - 30 Default Value: 3 Configuration Changed: Administrative
OBJECT-TYPE    
  INTEGER 1..30  

asioSapAdmPortStatisticsTimer 1.3.6.1.4.1.495.2.1.6.44.2.1.26
Determines the period of time, in seconds, that is used to measure Async driver performance and collect statistics. Range of Values: 0 - 60. Default Value: 0 = Performance statistics are not measured
OBJECT-TYPE    
  INTEGER 0..60  

asioSapAdmPortCarrierAction 1.3.6.1.4.1.495.2.1.6.44.2.1.27
Determines whether or not this SAP (service access point) will inform the associated upper layer SAP that service is no longer available because its associated hardware port has detected a loss of DCD (Data Carrier Detect) if the port is physically strapped as a DTE, or a loss of DTR (Data Terminal Ready) if the port is physically strapped as a DCE. Options: disabled (1) enabled (2) Default Value: enabled Configuration Changed: Administrative
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

asioAdmPortTrap 1.3.6.1.4.1.495.2.1.6.44.2.1.30
Indicates whether on not this SAP (service access point) produces the asyPortStatusChange trap. Options: disabled (1) enabled (2) Default Value: disabled Configuration Changed: Administrative
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

Defined Objects

AsioSapOprEntry  
SEQUENCE    
  INTEGER as asioSapOprNumber  
  Alias as asioSapOprAlias  
  INTEGER as asioSapOprPortSpeed  
  INTEGER as asioSapOprPortCharacterSize  
  INTEGER as asioSapOprPortStopBits  
  INTEGER as asioSapOprPortBreakLength  
  INTEGER as asioSapOprPortMaxQueueLength  
  INTEGER as asioSapOprPortQueueUpperThreshold  
  INTEGER as asioSapOprPortQueueLowerThreshold  
  INTEGER as asioSapOprPortSignalDownTimer  
  INTEGER as asioSapOprPortMaxTimeDelay  
  INTEGER as asioSapOprPortMaxInterruptCharacters  
  INTEGER as asioSapOprPortSignalSamplingPeriod  
  INTEGER as asioSapOprPortDcdDtrSignalSamples  
  INTEGER as asioSapOprPortCtsRtsSignalSamples  
  INTEGER as asioSapOprPortDsrDrsSignalSamples  
  INTEGER as asioSapOprPortTmLlSignalSamples  
  INTEGER as asioSapOprPortRiRlSignalSamples  
  INTEGER as asioSapOprPortStatisticsTimer  
  INTEGER as asioSapOprPortCarrierAction  
  INTEGER as asioOprPortTrap  
  INTEGER as asioOprControlLine  
  INTEGER as asioOprControlStats  
  INTEGER as asioStatOprPortType  
  INTEGER as asioStatOprPortInterfaceType  
  INTEGER as asioStatOprPortState  
  INTEGER as asioStatOprDCDState  
  INTEGER as asioStatOprDTRState  
  INTEGER as asioStatOprRTSState  
  INTEGER as asioStatOprCTSState  
  INTEGER as asioStatOprDSRState  
  INTEGER as asioStatOprDRSState  
  INTEGER as asioStatOprTMState  
  INTEGER as asioStatOprLLState  
  INTEGER as asioStatOprRIState  
  INTEGER as asioStatOprRLState  
  Counter as asioStatOprTxBps  
  Counter as asioStatOprRxBps  
  Counter as asioStatOprTxBpsMax  
  Counter as asioStatOprRxBpsMax  
  Counter as asioStatOprTxCharacters  
  Counter as asioStatOprTxBadStateDiscards  
  Counter as asioStatOprTxResetDiscards  
  Counter as asioStatOprTxSysCongestionDiscards  
  Counter as asioStatOprRxCharacters  
  Counter as asioStatOprRxOverrunErrorCharacters  
  Counter as asioStatOprRxParityErrorCharacters  
  Counter as asioStatOprRxFramingErrorCharacters  
  Counter as asioStatOprRxNoiseErrorCharacters  
  Counter as asioStatOprRxBreakCharacters  
  Counter as asioStatOprRxBadStateDiscards  
  Counter as asioStatOprRxBusyDiscards  
  Counter as asioStatOprPortStateChanges  
  Counter as asioStatOprDCDStateChanges  
  Counter as asioStatOprDTRStateChanges  
  Counter as asioStatOprRTSStateChanges  
  Counter as asioStatOprCTSStateChanges  
  Counter as asioStatOprDSRStateChanges  
  Counter as asioStatOprDRSStateChanges  
  Counter as asioStatOprTMStateChanges  
  Counter as asioStatOprLLStateChanges  
  Counter as asioStatOprRIStateChanges  
  Counter as asioStatOprRLStateChanges  
  Counter as asioStatOprPortResets  

AsioSapAdmEntry  
SEQUENCE    
  INTEGER as asioSapAdmNumber  
  Alias as asioSapAdmAlias  
  INTEGER as asioSapAdmPortSpeed  
  INTEGER as asioSapAdmPortCharacterSize  
  INTEGER as asioSapAdmPortStopBits  
  INTEGER as asioSapAdmPortBreakLength  
  INTEGER as asioSapAdmPortMaxQueueLength  
  INTEGER as asioSapAdmPortQueueUpperThreshold  
  INTEGER as asioSapAdmPortQueueLowerThreshold  
  INTEGER as asioSapAdmPortSignalDownTimer  
  INTEGER as asioSapAdmPortMaxTimeDelay  
  INTEGER as asioSapAdmPortMaxInterruptCharacters  
  INTEGER as asioSapAdmPortSignalSamplingPeriod  
  INTEGER as asioSapAdmPortDcdDtrSignalSamples  
  INTEGER as asioSapAdmPortCtsRtsSignalSamples  
  INTEGER as asioSapAdmPortDsrDrsSignalSamples  
  INTEGER as asioSapAdmPortTmLlSignalSamples  
  INTEGER as asioSapAdmPortRiRlSignalSamples  
  INTEGER as asioSapAdmPortStatisticsTimer  
  INTEGER as asioSapAdmPortCarrierAction  
  INTEGER as asioAdmPortTrap