DES3526-L2MGMT-MIB

File: DES3526-L2MGMT-MIB.mib (158505 bytes)

Imported modules

SNMPv2-SMI SNMP-FRAMEWORK-MIB SNMPv2-TC
SW3500PRIMGMT-MIB RFC1213-MIB

Imported symbols

Counter32 Counter64 TimeTicks
NOTIFICATION-TYPE MODULE-IDENTITY OBJECT-TYPE
IpAddress Unsigned32 SnmpAdminString
MacAddress RowStatus des3526
DisplayString

Defined Objects

swL2MgmtMIB 1.3.6.1.4.1.171.11.64.1.2
The Structure of Layer 2 Network Management Information for the proprietary enterprise.
MODULE-IDENTITY    

swL2DevMgmt 1.3.6.1.4.1.171.11.64.1.2.1
OBJECT IDENTIFIER    

swL2DevInfo 1.3.6.1.4.1.171.11.64.1.2.1.1
OBJECT IDENTIFIER    

swDevInfoSystemUpTime 1.3.6.1.4.1.171.11.64.1.2.1.1.1
The value of sysUpTime at the time the switch entered its current operational state. If the current state was entered prior to the last re-initialization, then this object contains a zero value. This value is in the units of seconds.
OBJECT-TYPE    
  TimeTicks  

swDevInfoTotalNumOfPort 1.3.6.1.4.1.171.11.64.1.2.1.1.2
The number of ports within this switch. This value is the sum of the ports within this switch.
OBJECT-TYPE    
  INTEGER 0..65535  

swDevInfoNumOfPortInUse 1.3.6.1.4.1.171.11.64.1.2.1.1.3
The number of ports in this switch connected to the segment or the end stations.
OBJECT-TYPE    
  INTEGER 0..65535  

swDevInfoConsoleInUse 1.3.6.1.4.1.171.11.64.1.2.1.1.4
The usage indication of the console system.
OBJECT-TYPE    
  INTEGER other(1), in-use(2), not-in-use(3)  

swDevInfoModuleType 1.3.6.1.4.1.171.11.64.1.2.1.1.5
This object indicates the module type of this port.
OBJECT-TYPE    
  OCTET STRING  

swDevInfoPowerTable 1.3.6.1.4.1.171.11.64.1.2.1.1.8
A list of the temperature.
OBJECT-TYPE    
  SEQUENCE OF  
    SwDevInfoPowerEntry

swDevInfoPowerEntry 1.3.6.1.4.1.171.11.64.1.2.1.1.8.1
An entry for Power information.
OBJECT-TYPE    
  SwDevInfoPowerEntry  

swDevInfoPowerUnitIndex 1.3.6.1.4.1.171.11.64.1.2.1.1.8.1.1
Indicates the ID of the unit in the System
OBJECT-TYPE    
  INTEGER 0..65535  

swDevInfoPowerID 1.3.6.1.4.1.171.11.64.1.2.1.1.8.1.2
Indicates ID of the power
OBJECT-TYPE    
  INTEGER 0..65535  

swDevInfoPowerStatus 1.3.6.1.4.1.171.11.64.1.2.1.1.8.1.3
Indicates status of the power
OBJECT-TYPE    
  INTEGER other(0), lowVoltage(1), overCurrent(2), working(3), fail(4), connect(5), disconnect(6)  

swL2DevCtrl 1.3.6.1.4.1.171.11.64.1.2.1.2
OBJECT IDENTIFIER    

swL2DevCtrlStpState 1.3.6.1.4.1.171.11.64.1.2.1.2.1
This object can enable or disable the spanning tree algorithm during the runtime of the system.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2DevCtrlIGMPSnooping 1.3.6.1.4.1.171.11.64.1.2.1.2.2
This object indicates if the layer 2 Internet Group Management Protocol (IGMP) capture function has been enabled or disabled.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2DevCtrlRmonState 1.3.6.1.4.1.171.11.64.1.2.1.2.3
This object can be enable or disable RMON.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2DevCtrlCleanAllStatisticCounter 1.3.6.1.4.1.171.11.64.1.2.1.2.8
If the object is set to active, all the statistic counters will be cleared. If set to normal, do nothing.
OBJECT-TYPE    
  INTEGER normal(1), active(2)  

swL2DevCtrlVlanIdOfFDBTbl 1.3.6.1.4.1.171.11.64.1.2.1.2.9
Indicates the VLAN ID which the Dot1dTpFdbTable belongs to ; The default value is the DEFAULT_VLAN_ID of the system.
OBJECT-TYPE    
  VlanId  

swL2MACNotifyState 1.3.6.1.4.1.171.11.64.1.2.1.2.10
This object can enable or disable MAC Notification.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2MACNotifyHistorySize 1.3.6.1.4.1.171.11.64.1.2.1.2.11
This object indicates the history size of variation MAC in the address table. The default value is 1 .
OBJECT-TYPE    
  INTEGER 1..500  

swL2MACNotifyInterval 1.3.6.1.4.1.171.11.64.1.2.1.2.12
This object indicates the time interval in seconds for triggering the MAC notify message.
OBJECT-TYPE    
  INTEGER 1..2147483647  

swL2DevCtrlAsymVlanState 1.3.6.1.4.1.171.11.64.1.2.1.2.13
This object can enable or disable asymmetric VLANs during the runtime of the system.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2DevCtrlManagementVlanId 1.3.6.1.4.1.171.11.64.1.2.1.2.14
This object controls which Vlan includes system ip and that the Vlan should have been created.
OBJECT-TYPE    
  VlanId  

swL2DevCtrlTelnet 1.3.6.1.4.1.171.11.64.1.2.1.2.15
OBJECT IDENTIFIER    

swL2DevCtrlTelnetState 1.3.6.1.4.1.171.11.64.1.2.1.2.15.1
This object controls the Telnet status.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2DevCtrlTelnetTcpPort 1.3.6.1.4.1.171.11.64.1.2.1.2.15.2
This object can designate a TCP port. When Telnet is disabled this object isn't accessible.
OBJECT-TYPE    
  INTEGER 1..65535  

swL2DevCtrlLLDPState 1.3.6.1.4.1.171.11.64.1.2.1.2.16
Specifies the state of the LLDP function. When this function is enabled, the switch can start to transmit LLDP packets and receive and process the LLDP packets. The specific function of each port will depend on the per port LLDP setting. For the advertisement of LLDP packets, the switch announces the information to its neighbor through ports. For the receiving of LLDP packets, the switch will learn the information from the LLDP packets advertised from the neighbor in the neighbor table.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swL2DevCtrlWeb 1.3.6.1.4.1.171.11.64.1.2.1.2.17
OBJECT IDENTIFIER    

swL2DevCtrlWebState 1.3.6.1.4.1.171.11.64.1.2.1.2.17.1
This object controls Web status.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2DevCtrlWebTcpPort 1.3.6.1.4.1.171.11.64.1.2.1.2.17.2
This object can designate a TCP port. When Web is disabled this object isn't accessible.
OBJECT-TYPE    
  INTEGER 1..65535  

swL2DevCtrlLLDPForwardMessageState 1.3.6.1.4.1.171.11.64.1.2.1.2.18
When lldp is disabled and lldp forward_message is enabled, the received LLDP Data Unit packets will be forwarded.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swL2DevAlarm 1.3.6.1.4.1.171.11.64.1.2.1.3
OBJECT IDENTIFIER    

swL2DevAlarmNewRoot 1.3.6.1.4.1.171.11.64.1.2.1.3.1
When the device has become the new root of Spanning Tree, this object decides whether to send a new root trap.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2DevAlarmTopologyChange 1.3.6.1.4.1.171.11.64.1.2.1.3.2
This object determines whether to send a trap or not when the switch topology has changed. If the object is enabled(3), the topology change trap is sent by the device when any of its configured ports transition from the Learning state to the Forwarding state, or from the Forwarding state to the Blocking state. For the same port transition, the device doesn't send the trap if this object value is set to disabled or other.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2DevAlarmLinkChange 1.3.6.1.4.1.171.11.64.1.2.1.3.3
This object determines whether to send a trap or not when the link has changed. If the object is enabled (3), the Link Change trap is sent by the device when any of its port links change. The device doesn't send the trap if this object value is set to disabled or other.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2VlanMgmt 1.3.6.1.4.1.171.11.64.1.2.3
OBJECT IDENTIFIER    

swL2VlanAdvertisementTable 1.3.6.1.4.1.171.11.64.1.2.3.1
A table containing the advertisement state for each VLAN configured into the device by (local or network) management.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2VlanAdvertisementEntry

swL2VlanAdvertisementEntry 1.3.6.1.4.1.171.11.64.1.2.3.1.1
Advertisement state for each VLAN configured in the device.
OBJECT-TYPE    
  SwL2VlanAdvertisementEntry  

swL2VlanIndex 1.3.6.1.4.1.171.11.64.1.2.3.1.1.1
The VLAN-ID or other identifier referring to this VLAN.
OBJECT-TYPE    
  INTEGER 1..4094  

swL2VlanName 1.3.6.1.4.1.171.11.64.1.2.3.1.1.2
An administratively assigned string, which may be used to identify the VLAN.
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

swL2VlanAdvertiseState 1.3.6.1.4.1.171.11.64.1.2.3.1.1.3
This object indicates the advertised status of this VLAN entry.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2PortMgmt 1.3.6.1.4.1.171.11.64.1.2.4
OBJECT IDENTIFIER    

swL2PortInfoTable 1.3.6.1.4.1.171.11.64.1.2.4.1
A table that contains information about every port.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2PortInfoEntry

swL2PortInfoEntry 1.3.6.1.4.1.171.11.64.1.2.4.1.1
A list of information for each port of the device.
OBJECT-TYPE    
  SwL2PortInfoEntry  

swL2PortInfoPortIndex 1.3.6.1.4.1.171.11.64.1.2.4.1.1.1
This object indicates the module's port number.(1..Max port number in the module).
OBJECT-TYPE    
  INTEGER 0..65535  

swL2PortInfoUnitIndex 1.3.6.1.4.1.171.11.64.1.2.4.1.1.2
Indicates ID of the unit in the device
OBJECT-TYPE    
  INTEGER 0..65535  

swL2PortInfoType 1.3.6.1.4.1.171.11.64.1.2.4.1.1.3
This object indicates the connector type of this port.
OBJECT-TYPE    
  INTEGER portType-100Base-TX(1), portType-100Base-FX(2), portType-100Base-FL(3), portType-1000Base-TX(4), portType-1000Base-SX(5), portType-1000Base-LX(6), portType-1000Base-SX-GBIC(7), portType-1000Base-LX-GBIC(8), portType-1000Base-TX-GBIC(9), portType-1000Base-1394(10), none(11)  

swL2PortInfoLinkStatus 1.3.6.1.4.1.171.11.64.1.2.4.1.1.4
This object indicates the port link status.
OBJECT-TYPE    
  INTEGER other(1), link-pass(2), link-fail(3)  

swL2PortInfoNwayStatus 1.3.6.1.4.1.171.11.64.1.2.4.1.1.5
This object indicates the port speed and duplex mode.
OBJECT-TYPE    
  INTEGER other(1), auto(2), half-10Mbps(3), full-10Mbps(4), half-100Mbps(5), full-100Mbps(6), half-1Gigabps(7), full-1Gigabps(8)  

swL2PortInfoModuleType 1.3.6.1.4.1.171.11.64.1.2.4.1.1.6
This object indicates the module type of this port.
OBJECT-TYPE    
  INTEGER none(0), moduleType-COMBO(1), moduleType-1394(2), moduleType-1000T(3), moduleType-MGBIC(4), moduleType-1P-SC-SX(5), moduleType-2P-SC-SX(6), moduleType-1P-SC-LX(7), moduleType-2P-SC-LX(8), moduleType-1P-TX(9), moduleType-2P-TX(10), moduleType-1P-MTRJ-SX(11), moduleType-2P-MTRJ-SX(12), moduleType-1P-MTRJ-LX(13), moduleType-2P-MTRJ-LX(14), moduleType-1P-GBIC(15), moduleType-2P-GBIC(16), moduleType-1P-GBIC-1P-TX(17), moduleType-1P-GBIC-1P-STACK(18), moduleType-2P-STACK(19), moduleType-2P-100FX(20), moduleType-1P-100FX(21), moduleType-2P-100FX-NEW(22), moduleType-1P-100FL(23), moduleType-2P-100FL(24), moduleType-2P-100TX(25), moduleType-BaseModule-24PORT(26)  

swL2PortInfoErrorDisabled 1.3.6.1.4.1.171.11.64.1.2.4.1.1.7
This object indicates the blocking type of this port.
OBJECT-TYPE    
  INTEGER none(0), storm(1), lbd(2), unknow(3)  

swL2PortCtrlTable 1.3.6.1.4.1.171.11.64.1.2.4.2
A table that contains control information about every port.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2PortCtrlEntry

swL2PortCtrlEntry 1.3.6.1.4.1.171.11.64.1.2.4.2.1
A list of control information for each port of the device.
OBJECT-TYPE    
  SwL2PortCtrlEntry  

swL2PortCtrlPortIndex 1.3.6.1.4.1.171.11.64.1.2.4.2.1.1
This object indicates the module's port number.(1..Max port number in the module)
OBJECT-TYPE    
  INTEGER 0..65535  

swL2PortCtrlUnitIndex 1.3.6.1.4.1.171.11.64.1.2.4.2.1.2
Indicates the ID of the unit in the device
OBJECT-TYPE    
  INTEGER 0..65535  

swL2PortCtrlAdminState 1.3.6.1.4.1.171.11.64.1.2.4.2.1.3
This object decides whether the port is enabled or disabled.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2PortCtrlNwayState 1.3.6.1.4.1.171.11.64.1.2.4.2.1.4
Choose the port speed, duplex mode, and N-Way function mode.
OBJECT-TYPE    
  INTEGER other(1), nway-enabled(2), nway-disabled-10Mbps-Half(3), nway-disabled-10Mbps-Full(4), nway-disabled-100Mbps-Half(5), nway-disabled-100Mbps-Full(6), nway-disabled-1Gigabps-Half(7), nway-disabled-1Gigabps-Full(8)  

swL2PortCtrlFlowCtrlState 1.3.6.1.4.1.171.11.64.1.2.4.2.1.5
The flow control mechanism is different between full duplex mode and half duplex mode. For half duplex mode, the jamming signal is asserted. For full duplex mode, IEEE 802.3x flow control function sends PAUSE frames and receives PAUSE frames.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2PortCtrlLockState 1.3.6.1.4.1.171.11.64.1.2.4.2.1.6
This object decides whether the port is locked or not.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2PortCtrlMACNotifyState 1.3.6.1.4.1.171.11.64.1.2.4.2.1.7
This object decides whether MAC notification is enabled or not.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2PortCtrlMulticastfilter 1.3.6.1.4.1.171.11.64.1.2.4.2.1.8
This object decides the multicast packet filtering mode on this port .
OBJECT-TYPE    
  INTEGER other(0), forward-all-groups(1), forward-unregistered-groups(2), filter-unregistered-groups(3)  

swL2PortCtrlMdixState 1.3.6.1.4.1.171.11.64.1.2.4.2.1.11
This object decides the MDIX mode on this port.
OBJECT-TYPE    
  INTEGER auto(1), normal(2), cross(3)  

swL2PortInformationTable 1.3.6.1.4.1.171.11.64.1.2.4.4
A table that contains information about every port.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2PortInformationEntry

swL2PortInformationEntry 1.3.6.1.4.1.171.11.64.1.2.4.4.1
A list of information for each port of the device.
OBJECT-TYPE    
  SwL2PortInformationEntry  

swL2PortInformationPortIndex 1.3.6.1.4.1.171.11.64.1.2.4.4.1.1
This object indicates the module's port number.(1..Max port number in the module)
OBJECT-TYPE    
  INTEGER 0..65535  

swL2PortInformationMediumType 1.3.6.1.4.1.171.11.64.1.2.4.4.1.2
Indicates medium type of the port number.
OBJECT-TYPE    
  INTEGER copper(1), fiber(2)  

swL2PortInformationUnitID 1.3.6.1.4.1.171.11.64.1.2.4.4.1.3
Indicates ID of the unit in the system
OBJECT-TYPE    
  INTEGER 0..65535  

swL2PortInformationType 1.3.6.1.4.1.171.11.64.1.2.4.4.1.4
This object indicates the connector type of this port.
OBJECT-TYPE    
  INTEGER portType-100Base-TX(1), portType-100Base-FX(2), portType-100Base-FL(3), portType-1000Base-TX(4), portType-1000Base-SX(5), portType-1000Base-LX(6), portType-1000Base-SX-GBIC(7), portType-1000Base-LX-GBIC(8), portType-1000Base-TX-GBIC(9), portType-1000Base-1394(10), portType-1000Base-TX-GBIC-COMBO(11), portType-1000Base-none-GBIC(12), portType-1000Base-SX-MGBIC(13), portType-1000Base-LX-MGBIC(14), portType-1000Base-TX-MGBIC(15), portType-1000Base-none-MGBIC(16), portType-SIO(17), portType-10G(18), portType-10G-xenpak-1310nm(19), portType-10G-xenpak-850nm(20), portType-10G-xenpak-empty(21), portType-10G-xfp-1310nm(22), portType-10G-xfp-850nm(23), portType-10G-xfp-empty(24), portType-none(25)  

swL2PortInformationLinkStatus 1.3.6.1.4.1.171.11.64.1.2.4.4.1.5
This object indicates the port link status.
OBJECT-TYPE    
  INTEGER other(1), link-pass(2), link-fail(3)  

swL2PortInformationNwayStatus 1.3.6.1.4.1.171.11.64.1.2.4.4.1.6
This object indicates the port speed and duplex mode.
OBJECT-TYPE    
  INTEGER other(0), empty(1), link-down(2), half-10Mbps(3), full-10Mbps(4), half-100Mbps(5), full-100Mbps(6), half-1Gigabps(7), full-1Gigabps(8), full-10Gigabps(9)  

swL2PortInformationModuleType 1.3.6.1.4.1.171.11.64.1.2.4.4.1.7
This object indicates the module type of this port.
OBJECT-TYPE    
  INTEGER none(0), moduleType-COMBO(1), moduleType-1394(2), moduleType-1000T(3), moduleType-MGBIC(4), moduleType-1P-SC-SX(5), moduleType-2P-SC-SX(6), moduleType-1P-SC-LX(7), moduleType-2P-SC-LX(8), moduleType-1P-TX(9), moduleType-2P-TX(10), moduleType-1P-MTRJ-SX(11), moduleType-2P-MTRJ-SX(12), moduleType-1P-MTRJ-LX(13), moduleType-2P-MTRJ-LX(14), moduleType-1P-GBIC(15), moduleType-2P-GBIC(16), moduleType-1P-GBIC-1P-TX(17), moduleType-1P-GBIC-1P-STACK(18), moduleType-2P-STACK(19), moduleType-2P-100FX(20), moduleType-1P-100FX(21), moduleType-2P-100FX-NEW(22), moduleType-1P-100FL(23), moduleType-2P-100FL(24), moduleType-2P-100TX(25), moduleType-BaseModule-24PORT(26)  

swL2PortInformationErrorDisabled 1.3.6.1.4.1.171.11.64.1.2.4.4.1.8
This object indicates the blocking type of this port.
OBJECT-TYPE    
  INTEGER none(0), storm(1), lbd(2), unknow(3)  

swL2PortControlTable 1.3.6.1.4.1.171.11.64.1.2.4.5
A table that contains control information about every port.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2PortControlEntry

swL2PortControlEntry 1.3.6.1.4.1.171.11.64.1.2.4.5.1
A list of control information for each port of the device.
OBJECT-TYPE    
  SwL2PortControlEntry  

swL2PortControlPortIndex 1.3.6.1.4.1.171.11.64.1.2.4.5.1.1
This object indicates the module's port number.(1..Max port number in the module)
OBJECT-TYPE    
  INTEGER 0..65535  

swL2PortControlMediumType 1.3.6.1.4.1.171.11.64.1.2.4.5.1.2
Indicates the medium type of the port number.
OBJECT-TYPE    
  INTEGER copper(1), fiber(2)  

swL2PortControlUnitIndex 1.3.6.1.4.1.171.11.64.1.2.4.5.1.3
Indicates ID of the unit in the device
OBJECT-TYPE    
  INTEGER 0..65535  

swL2PortControlAdminState 1.3.6.1.4.1.171.11.64.1.2.4.5.1.4
This object decides if the port is enabled or disabled.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2PortControlNwayState 1.3.6.1.4.1.171.11.64.1.2.4.5.1.5
Choose the port speed, duplex mode, and N-Way function mode.
OBJECT-TYPE    
  INTEGER other(1), nway-enabled(2), nway-disabled-10Mbps-Half(3), nway-disabled-10Mbps-Full(4), nway-disabled-100Mbps-Half(5), nway-disabled-100Mbps-Full(6), nway-disabled-1Gigabps-Half(7), nway-disabled-1Gigabps-Full(8), nway-disabled-1Gigabps-Full-master(9), nway-disabled-1Gigabps-Full-slave(10)  

swL2PortControlFlowCtrlState 1.3.6.1.4.1.171.11.64.1.2.4.5.1.6
The flow control mechanism is different between full duplex mode and half duplex mode. For half duplex mode, the jamming signal is asserted. For full duplex mode, the IEEE 802.3x flow control function sends PAUSE frames and receives PAUSE frames.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2PortControlLockState 1.3.6.1.4.1.171.11.64.1.2.4.5.1.7
This object decides whether the port is locked or not.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2PortControlMACNotifyState 1.3.6.1.4.1.171.11.64.1.2.4.5.1.8
This object sets each port's MAC notification state.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2PortControlMulticastfilter 1.3.6.1.4.1.171.11.64.1.2.4.5.1.9
This object controls the multicast port filtering mode for a specified port.
OBJECT-TYPE    
  INTEGER other(0), forward-all-groups(1), forward-unregistered-groups(2), filter-unregistered-groups(3)  

swL2PortControlMdixState 1.3.6.1.4.1.171.11.64.1.2.4.5.1.11
This object decides the MDIX mode on this port.
OBJECT-TYPE    
  INTEGER auto(1), normal(2), cross(3)  

swL2LimitedMulticastMgmt 1.3.6.1.4.1.171.11.64.1.2.5
OBJECT IDENTIFIER    

swL2MulticastRangeTable 1.3.6.1.4.1.171.11.64.1.2.5.1
.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2MulticastRangeEntry

swL2MulticastRangeEntry 1.3.6.1.4.1.171.11.64.1.2.5.1.1
A list of information contained in swL2MulticastRangeTable.
OBJECT-TYPE    
  SwL2MulticastRangeEntry  

swL2MulticastRangeName 1.3.6.1.4.1.171.11.64.1.2.5.1.1.1
This object specifies the multicast range name.
OBJECT-TYPE    
  DisplayString  

swL2MulticastRangeFromIp 1.3.6.1.4.1.171.11.64.1.2.5.1.1.2
This object specifies the start IP address for this range.
OBJECT-TYPE    
  IpAddress  

swL2MulticastRangeToIp 1.3.6.1.4.1.171.11.64.1.2.5.1.1.3
This object specifies the end IP address for this range.
OBJECT-TYPE    
  IpAddress  

swL2MulticastRangeRowStatus 1.3.6.1.4.1.171.11.64.1.2.5.1.1.4
This object indicates the status of this entry.
OBJECT-TYPE    
  RowStatus  

swL2LimitedMulticastPortInfo 1.3.6.1.4.1.171.11.64.1.2.5.2
OBJECT IDENTIFIER    

swL2LimitedMulticastStatusTable 1.3.6.1.4.1.171.11.64.1.2.5.2.1
.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2LimitedMulticastStatusEntry

swL2LimitedMulticastStatusEntry 1.3.6.1.4.1.171.11.64.1.2.5.2.1.1
A list of information contained in swL2LimitedMulticastStatusTable.
OBJECT-TYPE    
  SwL2LimitedMulticastStatusEntry  

swL2LimitedMulticastPort 1.3.6.1.4.1.171.11.64.1.2.5.2.1.1.1
This object indicates the port.
OBJECT-TYPE    
  INTEGER 1..65535  

swL2LimitedMulticastAccess 1.3.6.1.4.1.171.11.64.1.2.5.2.1.1.2
This object indicates the access type.
OBJECT-TYPE    
  INTEGER none(1), permit(2), deny(3)  

swL2LimitedMulticastState 1.3.6.1.4.1.171.11.64.1.2.5.2.1.1.3
This object indicates the state for this port.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2LimitedMulticastRangeTable 1.3.6.1.4.1.171.11.64.1.2.5.2.2
.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2LimitedMulticastRangeEntry

swL2LimitedMulticastRangeEntry 1.3.6.1.4.1.171.11.64.1.2.5.2.2.1
A list of information contained in swL2LimitedMulticastRangeTable.
OBJECT-TYPE    
  SwL2LimitedMulticastRangeEntry  

swL2LimitedMulticastID 1.3.6.1.4.1.171.11.64.1.2.5.2.2.1.1
This object indicates the range ID.
OBJECT-TYPE    
  INTEGER 1..65535  

swL2LimitedMulticastRangeName 1.3.6.1.4.1.171.11.64.1.2.5.2.2.1.2
OBJECT-TYPE    
  DisplayString  

swL2LimitedMulticastFromIp 1.3.6.1.4.1.171.11.64.1.2.5.2.2.1.3
This object specifies the start IP address of the range on this port.
OBJECT-TYPE    
  IpAddress  

swL2LimitedMulticastToIp 1.3.6.1.4.1.171.11.64.1.2.5.2.2.1.4
This object specifies the end IP address of the range on this port.
OBJECT-TYPE    
  IpAddress  

swL2LimitedMulticastRowStatus 1.3.6.1.4.1.171.11.64.1.2.5.2.2.1.5
This object indicates the status of this entry.
OBJECT-TYPE    
  RowStatus  

swL2QOSMgmt 1.3.6.1.4.1.171.11.64.1.2.6
OBJECT IDENTIFIER    

swL2QOSBandwidthControlTable 1.3.6.1.4.1.171.11.64.1.2.6.1
.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2QOSBandwidthControlEntry

swL2QOSBandwidthControlEntry 1.3.6.1.4.1.171.11.64.1.2.6.1.1
A list of information contained in swL2QOSBandwidthControlTable.
OBJECT-TYPE    
  SwL2QOSBandwidthControlEntry  

swL2QOSBandwidthPortIndex 1.3.6.1.4.1.171.11.64.1.2.6.1.1.1
Indicates the port.
OBJECT-TYPE    
  INTEGER 1..650  

swL2QOSBandwidthRxRate 1.3.6.1.4.1.171.11.64.1.2.6.1.1.2
Indicates the RX Rate(Mbit/sec) of the specifed port. Value 0 means no limit.
OBJECT-TYPE    
  INTEGER 0..1000  

swL2QOSBandwidthTxRate 1.3.6.1.4.1.171.11.64.1.2.6.1.1.3
Indicates the TX Rate(Mbit/sec) of the specifed port. Value 0 means no limit.
OBJECT-TYPE    
  INTEGER 0..1000  

swL2QOSBandwidthRadiusRxRate 1.3.6.1.4.1.171.11.64.1.2.6.1.1.4
The Rx Rate value comes from the RADIUS server, If an 802.1X port is authenticated, this value will overwrite the locally configured Rx Rate.
OBJECT-TYPE    
  INTEGER  

swL2QOSBandwidthRadiusTxRate 1.3.6.1.4.1.171.11.64.1.2.6.1.1.5
The Tx Rate value comes from the RADIUS server, If an 802.1X port is authenticated, this value will overwrite the locally configured Tx Rate.
OBJECT-TYPE    
  INTEGER  

swL2QOSSchedulingTable 1.3.6.1.4.1.171.11.64.1.2.6.2
.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2QOSSchedulingEntry

swL2QOSSchedulingEntry 1.3.6.1.4.1.171.11.64.1.2.6.2.1
A list of information contained in swL2QOSSchedulingTable.
OBJECT-TYPE    
  SwL2QOSSchedulingEntry  

swL2QOSSchedulingClassIndex 1.3.6.1.4.1.171.11.64.1.2.6.2.1.1
Indicates the hardware queue number.
OBJECT-TYPE    
  INTEGER 0..3  

swL2QOSSchedulingMaxPkts 1.3.6.1.4.1.171.11.64.1.2.6.2.1.2
Indicates the maximum number of packets the hardware priority queue will be allowed to transmit before allowing the next lowest priority queue to transmit its packets. a value between 0 and 255 can be specified.
OBJECT-TYPE    
  INTEGER 0..255  

swL2QOSSchedulingMaxLatency 1.3.6.1.4.1.171.11.64.1.2.6.2.1.3
Indicates the maximum amount of time the hardware priority queue will be allowed to transmit packets before allowing the next lowest priority queue to begin transmitting its packets. A value between 0 and 255 can be specified- with this value multiplied by 16 ms to arrive at the total allowed time for queue to transmit packets. For example, a value of 3 specifies 3*16=48 ms. The queue will continue transmitting the last packet until it is finished when the max_latency timer expires.
OBJECT-TYPE    
  INTEGER 0..255  

swL2QOS8021pUserPriorityTable 1.3.6.1.4.1.171.11.64.1.2.6.3
.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2QOS8021pUserPriorityEntry

swL2QOS8021pUserPriorityEntry 1.3.6.1.4.1.171.11.64.1.2.6.3.1
A list of information contained in swL2QOS8021pUserPriorityTable.
OBJECT-TYPE    
  SwL2QOS8021pUserPriorityEntry  

swL2QOS8021pUserPriorityIndex 1.3.6.1.4.1.171.11.64.1.2.6.3.1.1
The 802.1p user priority .
OBJECT-TYPE    
  INTEGER 0..7  

swL2QOS8021pUserPriorityClass 1.3.6.1.4.1.171.11.64.1.2.6.3.1.2
The number of the switch's hardware priority queue. The switch has four hardware priority queues available. They are numbered between 0 (the lowest priority) and 3 (the highest priority).
OBJECT-TYPE    
  INTEGER 0..3  

swL2QOS8021pDefaultPriorityTable 1.3.6.1.4.1.171.11.64.1.2.6.4
.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2QOS8021pDefaultPriorityEntry

swL2QOS8021pDefaultPriorityEntry 1.3.6.1.4.1.171.11.64.1.2.6.4.1
A list of information contained in swL2QOS8021pDefaultPriorityTable.
OBJECT-TYPE    
  SwL2QOS8021pDefaultPriorityEntry  

swL2QOS8021pDefaultPriorityIndex 1.3.6.1.4.1.171.11.64.1.2.6.4.1.1
Indicates the port number.
OBJECT-TYPE    
  INTEGER 1..650  

swL2QOS8021pDefaultPriority 1.3.6.1.4.1.171.11.64.1.2.6.4.1.2
The priority value to assign to untagged packets received by the switch ports on the switch.
OBJECT-TYPE    
  INTEGER 0..7  

swL2QOS8021pRadiusPriority 1.3.6.1.4.1.171.11.64.1.2.6.4.1.3
Indicates the value of 802.1p comes from RADIUS server. If an 802.1X port is authenticated, this value will overwrite the local configured value.
OBJECT-TYPE    
  INTEGER  

swL2IpMacBindingMgmt 1.3.6.1.4.1.171.11.64.1.2.7
OBJECT IDENTIFIER    

swL2IpMacBindingPortTable 1.3.6.1.4.1.171.11.64.1.2.7.1
The table specifies the port's ip-mac binding function.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2IpMacBindingPortEntry

swL2IpMacBindingPortEntry 1.3.6.1.4.1.171.11.64.1.2.7.1.1
A list of information about the port's ip-mac binding function.
OBJECT-TYPE    
  SwL2IpMacBindingPortEntry  

swL2IpMacBindingPortIndex 1.3.6.1.4.1.171.11.64.1.2.7.1.1.1
This object indicates the module's port number.(1..Max port number in the module).
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IpMacBindingPortState 1.3.6.1.4.1.171.11.64.1.2.7.1.1.2
This object enables (strict or loose mode)/disables IP-MAC binding on the specified port. Note: enable-strict (2): SW learning enable-loose (4) : HW learning
OBJECT-TYPE    
  INTEGER other(1), enable-strict(2), disable(3), enable-loose(4)  

swL2IpMacBindingPortAllowZeroIp 1.3.6.1.4.1.171.11.64.1.2.7.1.1.3
This object enables/disables the allow zero IP status on the specified port.
OBJECT-TYPE    
  INTEGER other(1), enable(2), disable(3)  

swL2IpMacBindingPortForwardDhcpPkt 1.3.6.1.4.1.171.11.64.1.2.7.1.1.4
This object can be set to forward or not forward DHCP packets on the specified port.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swL2IpMacBindingPortDHCPSnoopMaxEntry 1.3.6.1.4.1.171.11.64.1.2.7.1.1.5
This object indicates the max entry created by DHCP packets on the specified port. Note: When 0 is set on the specified port, the max entry created by DHCP packets is no limit
OBJECT-TYPE    
  INTEGER 0..10  

swL2IpMacBindingPortDHCPSnoopEntryClearAction 1.3.6.1.4.1.171.11.64.1.2.7.1.1.6
When set to start(2), the address binding entries learned for the specified ports will be cleared. When get, it always returns other (1).
OBJECT-TYPE    
  INTEGER other(1), start(2)  

swL2IpMacBindingTable 1.3.6.1.4.1.171.11.64.1.2.7.2
This table specifies IP-MAC binding information.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2IpMacBindingEntry

swL2IpMacBindingEntry 1.3.6.1.4.1.171.11.64.1.2.7.2.1
IP-MAC binding entry used to add\delete\configure the address pair to the switch's authorized user database.
OBJECT-TYPE    
  SwL2IpMacBindingEntry  

swL2IpMacBindingIpIndex 1.3.6.1.4.1.171.11.64.1.2.7.2.1.1
The IP address of the IP-MAC binding.
OBJECT-TYPE    
  IpAddress  

swL2IpMacBindingMac 1.3.6.1.4.1.171.11.64.1.2.7.2.1.2
The MAC address of the IP-MAC binding.
OBJECT-TYPE    
  MacAddress  

swL2IpMacBindingStatus 1.3.6.1.4.1.171.11.64.1.2.7.2.1.3
The status of this entry.
OBJECT-TYPE    
  RowStatus  

swL2IpMacBindingPorts 1.3.6.1.4.1.171.11.64.1.2.7.2.1.4
The port members of this entry.
OBJECT-TYPE    
  PortList  

swL2IpMacBindingAction 1.3.6.1.4.1.171.11.64.1.2.7.2.1.5
The action of this entry.
OBJECT-TYPE    
  INTEGER inactive(0), active(1)  

swL2IpMacBindingMode 1.3.6.1.4.1.171.11.64.1.2.7.2.1.6
The mode of this entry. arp: This entry is specified as an ARP mode entry, and this entry will not be added as an access entry. If this object is not specified, the mode defaults to ARP mode. If the system is in ARP mode, the ARP mode entries and ACL mode entries will be effective. If the system is in ACL mode, only the ACL mode entries will be active. acl: This entry is specified as an ACL mode entry. If the user enables the ACL mode, this entry will be added as an access entry. auto: This mode cannot be configured, and when the auto mode is employed, it means this entry is to be learned by DHCP snooping.
OBJECT-TYPE    
  INTEGER arp(0), acl(1), auto(2)  

swL2IpMacBindingBlockedTable 1.3.6.1.4.1.171.11.64.1.2.7.3
The table specifies information of MAC addresses which were blocked.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2IpMacBindingBlockedEntry

swL2IpMacBindingBlockedEntry 1.3.6.1.4.1.171.11.64.1.2.7.3.1
The entry can not create/configure. It can only delete.
OBJECT-TYPE    
  SwL2IpMacBindingBlockedEntry  

swL2IpMacBindingBlockedVID 1.3.6.1.4.1.171.11.64.1.2.7.3.1.1
The object specifies the VLAN ID.
OBJECT-TYPE    
  VlanIndex  

swL2IpMacBindingBlockedMac 1.3.6.1.4.1.171.11.64.1.2.7.3.1.2
The MAC address which was blocked.
OBJECT-TYPE    
  MacAddress  

swL2IpMacBindingBlockedVlanName 1.3.6.1.4.1.171.11.64.1.2.7.3.1.3
This object specifies the VLAN name.
OBJECT-TYPE    
  DisplayString  

swL2IpMacBindingBlockedPort 1.3.6.1.4.1.171.11.64.1.2.7.3.1.4
The port with which the MAC is associated.
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IpMacBindingBlockedType 1.3.6.1.4.1.171.11.64.1.2.7.3.1.5
The value is always blockByAddrBind. This entry will be deleted by setting the value to delete(3).
OBJECT-TYPE    
  INTEGER other(1), blockByAddrBind(2), delete(3)  

swL2IpMacBindingAllPortState 1.3.6.1.4.1.171.11.64.1.2.7.4
This object enables/disables IP-MAC binding on all ports of the system. This action is only applicable when users have write privileges, and can only be viewed when users have read privileges. Note: enable-strict (2): This means strict mode (SW learning). All packets are sent to the CPU. If the user chooses, the port will check ARP packets and IP packets by IP-MAC-PORT Binding entries. If the MAC address can be found or not found by the entry, the MAC will be set as dynamic learned or it will set as blocked, respectively. Other packets will be sent to the CPU and dropped. enable-loose (4) : This means loose mode (HW learning): Only ARP packets and IP broadcast packets will be sent to the CPU. If the user chooses , the port will learn the MAC address on non-ARP and non-IP broadcast packets directly, so these packets will be bypassed. But if the switch receives the ARP or IP broadcast packets and Can not bypass the IP MAC Binding checking, the switch will set this MAC address as blocked and all packets from this MAC address will be dropped.
OBJECT-TYPE    
  INTEGER other(1), enable-strict(2), disable(3), enable-loose(4)  

swL2IpMacBindingTrapLogState 1.3.6.1.4.1.171.11.64.1.2.7.5
when set to enable(2),whenever there's a new MAC that violates the pre-defined Ip Mac Binding configuration, the trap will be sent out and the relevant information will be logged into the system.
OBJECT-TYPE    
  INTEGER other(1), enable(2), disable(3)  

swL2IpMacBindingACLMode 1.3.6.1.4.1.171.11.64.1.2.7.6
when set to enable(2), the Ip Mac Binding will use acl mode
OBJECT-TYPE    
  INTEGER other(1), enable(2), disable(3)  

swL2IpMacBindingDHCPSnoopState 1.3.6.1.4.1.171.11.64.1.2.7.7
When the dhcp_snoop function is enabled, all address_binding disabled ports will act as DHCP server ports (the switch will learn IP addresses through DHCP server ports (by DHCP OFFER and DHCP ACK packets)). The auto-learned IP-MAC binding entry will be mapped to a specific source port based on the MAC address learning function. This entry will be created as an ACL-mode binding entry for this specific port. Each entry is associated with a lease time. When the lease time expires, the expired entry will be removed from this port. The automatically learned binding entry can be moved from one port to another port if the DHCP snooping function has learned that the MAC address has moved to a different port. Consider a case where DHCP snooping learns a binding entry, and the same IP-MAC binding entry has been statically configured. Suppose that the learned information is consistent with the statically configured entry, then the automatically learned entry will not be created. Suppose the entry is statically configured in ARP mode, since the automatically learned entry will be created in ACL mode, the entry will become ACL mode. Suppose the entry is statically configured on one port and the entry is automatically learned on another port, then both entries will exist. When the dhcp_snoop function is disabled, all of the automatically learned binding entries will be removed.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swL2IpMacBindingDHCPSnoopEntryClearAllState 1.3.6.1.4.1.171.11.64.1.2.7.8
Used to clear all entries created by DHCP packets.
OBJECT-TYPE    
  INTEGER other(1), start(2)  

swL2IpMacBindingDHCPSnoopTable 1.3.6.1.4.1.171.11.64.1.2.7.9
The table specifies information regarding the DHCP snooping function learning IP-MAC binding entries.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2IpMacBindingDHCPSnoopEntry

swL2IpMacBindingDHCPSnoopEntry 1.3.6.1.4.1.171.11.64.1.2.7.9.1
A list of information about the DHCP snooping learning IP-MAC binding entry.
OBJECT-TYPE    
  SwL2IpMacBindingDHCPSnoopEntry  

swL2IpMacBindingDHCPSnoopIpIndex 1.3.6.1.4.1.171.11.64.1.2.7.9.1.1
The IP address of this entry.
OBJECT-TYPE    
  IpAddress  

swL2IpMacBindingDHCPSnoopMac 1.3.6.1.4.1.171.11.64.1.2.7.9.1.2
The MAC address of this entry.
OBJECT-TYPE    
  MacAddress  

swL2IpMacBindingDHCPSnoopLeaseTime 1.3.6.1.4.1.171.11.64.1.2.7.9.1.3
Specifies the lease time of this entry. When the lease time expires, this entry will be removed from this port.
OBJECT-TYPE    
  INTEGER  

swL2IpMacBindingDHCPSnoopPort 1.3.6.1.4.1.171.11.64.1.2.7.9.1.4
Specifies the port of this entry.
OBJECT-TYPE    
  INTEGER  

swL2IpMacBindingDHCPSnoopStatus 1.3.6.1.4.1.171.11.64.1.2.7.9.1.5
Specifies the status (inactive or active) of this entry.
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

swL2IpMacBindingPermitIPPoolTable 1.3.6.1.4.1.171.11.64.1.2.7.10
This table specifies the permitted IP pool of IP-MAC binding.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2IpMacBindingPermitIPPoolEntry

swL2IpMacBindingPermitIPPoolEntry 1.3.6.1.4.1.171.11.64.1.2.7.10.1
A list of information of each permitted IP pool entry.
OBJECT-TYPE    
  SwL2IpMacBindingPermitIPPoolEntry  

swL2IpMacBindingPermitIPPoolStartIP 1.3.6.1.4.1.171.11.64.1.2.7.10.1.1
The start IP address of the permitted IP pool.
OBJECT-TYPE    
  IpAddress  

swL2IpMacBindingPermitIPPoolEndIP 1.3.6.1.4.1.171.11.64.1.2.7.10.1.2
The end IP address of the permitted IP pool.
OBJECT-TYPE    
  IpAddress  

swL2IpMacBindingPermitIPPoolPorts 1.3.6.1.4.1.171.11.64.1.2.7.10.1.3
The port members of the permitted IP pool.
OBJECT-TYPE    
  PortList  

swL2IpMacBindingPermitIPPoolStatus 1.3.6.1.4.1.171.11.64.1.2.7.10.1.4
The status of the permitted IP pool.
OBJECT-TYPE    
  RowStatus  

swL2TrunkMgmt 1.3.6.1.4.1.171.11.64.1.2.8
OBJECT IDENTIFIER    

swL2TrunkMaxSupportedEntries 1.3.6.1.4.1.171.11.64.1.2.8.1
Maximum number of entries in the trunk configuration table (swL2TrunkCtrlTable).
OBJECT-TYPE    
  INTEGER 0..65535  

swL2TrunkCurrentNumEntries 1.3.6.1.4.1.171.11.64.1.2.8.2
Current active number of entries in the trunk configuration table.
OBJECT-TYPE    
  INTEGER 0..65535  

swL2TrunkCtrlTable 1.3.6.1.4.1.171.11.64.1.2.8.3
This table specifies which ports are grouped as a set of ports(up to 8) into a single logical link.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2TrunkCtrlEntry

swL2TrunkCtrlEntry 1.3.6.1.4.1.171.11.64.1.2.8.3.1
A list of information specifies which ports are grouped as a set of ports(up to 8) into a single logical link.
OBJECT-TYPE    
  SwL2TrunkCtrlEntry  

swL2TrunkIndex 1.3.6.1.4.1.171.11.64.1.2.8.3.1.1
The index of logical port trunk. The trunk group number depends on the existence of the unit and module.
OBJECT-TYPE    
  INTEGER 0..65535  

swL2TrunkName 1.3.6.1.4.1.171.11.64.1.2.8.3.1.2
The name of logical port trunk.
OBJECT-TYPE    
  DisplayString SIZE(0..12)  

swL2TrunkMasterPort 1.3.6.1.4.1.171.11.64.1.2.8.3.1.3
The object indicates the master port number of the port trunk entry. When using Port Trunk, you can not configure the other ports of the group except the master port. Their configuration must be the same as the master port (e.g. speed, duplex, enabled/disabled, flow control, and so on).
OBJECT-TYPE    
  INTEGER 1..65535  

swL2TrunkMember 1.3.6.1.4.1.171.11.64.1.2.8.3.1.4
Indicates how many ports are included in this Trunk. The trunk port number depends on the existence of module. The maximum number of ports is 8 for one trunks.
OBJECT-TYPE    
  PortList  

swL2TrunkFloodingPort 1.3.6.1.4.1.171.11.64.1.2.8.3.1.5
The object indicates the flooding port number of the port trunk entry. The first port of the trunk is implicitly configured to be the flooding port.
OBJECT-TYPE    
  INTEGER 1..65535  

swL2TrunkType 1.3.6.1.4.1.171.11.64.1.2.8.3.1.6
This object indicates the type of the trunk group. static : is static trunk group lacp : is LACP trunk group .
OBJECT-TYPE    
  INTEGER other(1), static(2), lacp(3)  

swL2TrunkState 1.3.6.1.4.1.171.11.64.1.2.8.3.1.7
This object indicates the status of this entry.
OBJECT-TYPE    
  RowStatus  

swL2TrunkAlgorithm 1.3.6.1.4.1.171.11.64.1.2.8.4
This object configures the part of the packet examined by the switch when selecting the egress port for transmitting load-sharing data.
OBJECT-TYPE    
  INTEGER other(1), mac-source(2), mac-destination(3), mac-source-dest(4), ip-source(5), ip-destination(6), ip-source-dest(7)  

swL2MirrorMgmt 1.3.6.1.4.1.171.11.64.1.2.9
OBJECT IDENTIFIER    

swL2MirrorLogicTargetPort 1.3.6.1.4.1.171.11.64.1.2.9.1
This object indicates which port will sniff another port to the switch. A trunk port member cannot be configured as a target Snooping port. The port number is the sequential (logical) number which is also applied to bridge MIB, etc.
OBJECT-TYPE    
  INTEGER 0..65535  

swL2MirrorPortSourceIngress 1.3.6.1.4.1.171.11.64.1.2.9.2
This represents the ingress of the source port packet to be sniffed.
OBJECT-TYPE    
  PortList  

swL2MirrorPortSourceEgress 1.3.6.1.4.1.171.11.64.1.2.9.3
This represents the egress of the source port packet to be sniffed.
OBJECT-TYPE    
  PortList  

swL2MirrorPortState 1.3.6.1.4.1.171.11.64.1.2.9.4
This object indicates the port mirroring state. other(1) - this entry is currently in use but the conditions under which it will remain so are different for each of the following values. disabled(2) - writing this value to the object will remove the corresponding entry from the table. enabled(3) - this entry will reside in the table.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2IGMPMgmt 1.3.6.1.4.1.171.11.64.1.2.10
OBJECT IDENTIFIER    

swL2IGMPMaxSupportedVlans 1.3.6.1.4.1.171.11.64.1.2.10.1
Maximum number of VLANs in the layer 2 IGMP control table (swL2IGMPCtrlTable).
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IGMPCtrlTable 1.3.6.1.4.1.171.11.64.1.2.10.3
This table controls the VLAN's IGMP function. Its scale depends on the current VLAN state (swL2VlanInfoStatus). If VLAN is in disabled mode, there is only one entry in the table, with index 1. If VLAN is in Port-Base or 802.1q mode, the number of entries can be up to 12, with an index range from 1 to 12.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2IGMPCtrlEntry

swL2IGMPCtrlEntry 1.3.6.1.4.1.171.11.64.1.2.10.3.1
The entry in IGMP control table (swL2IGMPCtrlTable). The entry is effective only when IGMP capture switch (swL2DevCtrlIGMPSnooping) is enabled.
OBJECT-TYPE    
  SwL2IGMPCtrlEntry  

swL2IGMPCtrlVid 1.3.6.1.4.1.171.11.64.1.2.10.3.1.1
This object indicates the IGMP control entry's VLAN ID. If VLAN is disabled, the VID is always 0 and cannot be changed by management users. If VLAN is in Port-Base mode, the VID is arranged from 1 to 12, fixed form. If VLAN is in 802.1q mode, the VID setting can vary from 1 to 4094 by management user, and the Vid in each entry must be unique in the IGMP Control Table.
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IGMPQueryInterval 1.3.6.1.4.1.171.11.64.1.2.10.3.1.2
The frequency at which the IGMP Host-Query packets are transmitted on this switch.
OBJECT-TYPE    
  INTEGER 1..65535  

swL2IGMPMaxResponseTime 1.3.6.1.4.1.171.11.64.1.2.10.3.1.3
The maximum query response time on this switch.
OBJECT-TYPE    
  INTEGER 1..25  

swL2IGMPRobustness 1.3.6.1.4.1.171.11.64.1.2.10.3.1.4
The Robustness Variable allows tuning for the expected packet loss on a subnet. If a subnet is expected to have a high loss, the Robustness Variable may be increased. IGMP is robust to (Robustness Variable-1) packet losses.
OBJECT-TYPE    
  INTEGER 1..255  

swL2IGMPLastMemberQueryInterval 1.3.6.1.4.1.171.11.64.1.2.10.3.1.5
The Last Member Query Interval is the Max Response Time inserted into Group-Specific Queries sent in response to Leave Group messages, and is also the amount of time between Group-Specific Query messages.
OBJECT-TYPE    
  INTEGER 1..65535  

swL2IGMPHostTimeout 1.3.6.1.4.1.171.11.64.1.2.10.3.1.6
The timer value for sending IGMP query packet when none was sent by the host in the LAN. The timer works in per-VLAN basis. Our device will be activated to send the query message if the timer has expired. Please reference RFC2236-1997.
OBJECT-TYPE    
  INTEGER 1..16711450  

swL2IGMPRouteTimeout 1.3.6.1.4.1.171.11.64.1.2.10.3.1.7
The Router Timeout is how long a host must wait after hearing a Query before it may send any IGMPv2 messages.
OBJECT-TYPE    
  INTEGER 1..16711450  

swL2IGMPLeaveTimer 1.3.6.1.4.1.171.11.64.1.2.10.3.1.8
When a query receives a Leave Group message for a group that has group members on the reception interface, it sends Group-Specific Queries every swL2IGMPLeaveTimer to the group being left.
OBJECT-TYPE    
  INTEGER 0..16711450  

swL2IGMPQueryState 1.3.6.1.4.1.171.11.64.1.2.10.3.1.9
This object decides if the IGMP query is enabled or disabled.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2IGMPCurrentState 1.3.6.1.4.1.171.11.64.1.2.10.3.1.10
This object indicates the current IGMP query state.
OBJECT-TYPE    
  INTEGER other(1), querier(2), non-querier(3)  

swL2IGMPCtrlState 1.3.6.1.4.1.171.11.64.1.2.10.3.1.11
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different for each of the following values. disable(2) - IGMP funtion is disabled for this entry. enable(3) - IGMP funtion is enabled for this entry.
OBJECT-TYPE    
  INTEGER other(1), disable(2), enable(3)  

swL2IGMPQueryInfoTable 1.3.6.1.4.1.171.11.64.1.2.10.4
The table contains the current number of IGMP query packets which have been captured by this device, as well as the IGMP query packets sent by the device.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2IGMPQueryInfoEntry

swL2IGMPQueryInfoEntry 1.3.6.1.4.1.171.11.64.1.2.10.4.1
Information about current IGMP query information, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrState of associated VLAN entires are all enabled.
OBJECT-TYPE    
  SwL2IGMPQueryInfoEntry  

swL2IGMPInfoVid 1.3.6.1.4.1.171.11.64.1.2.10.4.1.1
This object indicates the VID of the associated IGMP info table entry. It follows swL2IGMPCtrlVid in the associated entry of the IGMP control table (swL2IGMPCtrlTable).
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IGMPInfoQueryCount 1.3.6.1.4.1.171.11.64.1.2.10.4.1.2
This object indicates the number of query packets received since the IGMP function has been enabled, on a per-VLAN basis.
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IGMPInfoTxQueryCount 1.3.6.1.4.1.171.11.64.1.2.10.4.1.3
This object indicates the send count of IGMP query messages, on a per-VLAN basis. In case of the IGMP timer expiration, the switch sends IGMP query packets to related VLAN member ports and increments this object by 1.
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IGMPInfoTable 1.3.6.1.4.1.171.11.64.1.2.10.5
The table containing current IGMP information which have been captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN entries are all enabled. Note that the priority of IGMP table entries is lower than the Filtering Table, i.e. if there is a table hash collision between the entries of the IGMP Table and the Filtering Table inside the switch H/W address table, the Filtering Table entry will overwrite the colliding entry of the IGMP Table. See swL2FilterMgmt description also.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2IGMPInfoEntry

swL2IGMPInfoEntry 1.3.6.1.4.1.171.11.64.1.2.10.5.1
Information about current IGMP information which was captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN entries are all enabled.
OBJECT-TYPE    
  SwL2IGMPInfoEntry  

swL2IGMPVid 1.3.6.1.4.1.171.11.64.1.2.10.5.1.1
This object indicates the VID of individual IGMP table entries. It shows the VID of IGMP report information captured on the network.
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IGMPGroupIpAddr 1.3.6.1.4.1.171.11.64.1.2.10.5.1.2
This object identifies group ip address which have been captured from the IGMP packet, on a per-Vlan basis.
OBJECT-TYPE    
  IpAddress  

swL2IGMPMacAddr 1.3.6.1.4.1.171.11.64.1.2.10.5.1.3
This object identifies mac addresses which correspond to swL2IGMPGroupIpAddr, on a per-Vlan basis.
OBJECT-TYPE    
  MacAddress  

swL2IGMPPortMap 1.3.6.1.4.1.171.11.64.1.2.10.5.1.4
This object indicates which ports belong to the same multicast group, on a per-Vlan basis. Each multicast group has a octect string to indicate with port map. The most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the switch is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'(Note that the setting of the bit corresponding to the port from which a frame is received is irrelevant). The 4 octets represent one unit port according to its logic port. If the unit has less then 32 port, the other ports don't care and just fill in zero.
OBJECT-TYPE    
  PortList  

swL2IGMPIpGroupReportCount 1.3.6.1.4.1.171.11.64.1.2.10.5.1.5
This object indicates how many report packets were received by the device corresponding with this entry where the IGMP function is enabled, on a per-Vlan basis.
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IGMPMulticastVlanTable 1.3.6.1.4.1.171.11.64.1.2.10.6
The information of the IGMP snooping multicast VLAN table.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2IGMPMulticastVlanEntry

swL2IGMPMulticastVlanEntry 1.3.6.1.4.1.171.11.64.1.2.10.6.1
The entry of swL2IGMPMulticastVlanTable.
OBJECT-TYPE    
  SwL2IGMPMulticastVlanEntry  

swL2IGMPMulticastVlanid 1.3.6.1.4.1.171.11.64.1.2.10.6.1.1
This object indicates the VLAN id of the IGMP snooping multicast VLAN entry.
OBJECT-TYPE    
  INTEGER 2..4094  

swL2IGMPMulticastVlanName 1.3.6.1.4.1.171.11.64.1.2.10.6.1.2
This object indicates the VLAN name of the IGMP snooping multicast VLAN entry.
OBJECT-TYPE    
  SnmpAdminString SIZE(0..32)  

swL2IGMPMulticastVlanSourcePort 1.3.6.1.4.1.171.11.64.1.2.10.6.1.3
This object indicates the portlist of the source ports of IGMP snooping multicast VLAN. The source ports will be set as tag ports of the VLAN entry and the IGMP control messages received from the member ports would be forwarded to the source ports.
OBJECT-TYPE    
  PortList  

swL2IGMPMulticastVlanMemberPort 1.3.6.1.4.1.171.11.64.1.2.10.6.1.4
This object indicates the portlist of the member ports of IGMP snooping multicast VLAN. The source ports will be set to untag ports of the vlan entry and the IGMP control messages received from the member ports would be forwarded to the source ports.
OBJECT-TYPE    
  PortList  

swL2IGMPMulticastVlanRowStatus 1.3.6.1.4.1.171.11.64.1.2.10.6.1.5
This object indicates the status of this entry.
OBJECT-TYPE    
  RowStatus  

swL2IGMPMulticastVlanReplaceSourceIP 1.3.6.1.4.1.171.11.64.1.2.10.6.1.6
This object is used to replace the source IP address in the IP header for IGMP control packets.
OBJECT-TYPE    
  IpAddress  

swL2IGMPRouterPortTable 1.3.6.1.4.1.171.11.64.1.2.10.7
The information of the router port table.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2IGMPRouterPortEntry

swL2IGMPRouterPortEntry 1.3.6.1.4.1.171.11.64.1.2.10.7.1
The entry of swL2IGMPRouterPortTable.
OBJECT-TYPE    
  SwL2IGMPRouterPortEntry  

swL2IGMPRouterPortVlanid 1.3.6.1.4.1.171.11.64.1.2.10.7.1.1
This object indicates the VLAN id of the router port entry.
OBJECT-TYPE    
  INTEGER 1..4094  

swL2IGMPRouterPortVlanName 1.3.6.1.4.1.171.11.64.1.2.10.7.1.2
This object indicates the VLAN name of the router port entry.
OBJECT-TYPE    
  SnmpAdminString SIZE(0..32)  

swL2IGMPRouterPortStaticPortList 1.3.6.1.4.1.171.11.64.1.2.10.7.1.3
This object indicates the static portlist of the router port entry.
OBJECT-TYPE    
  PortList  

swL2IGMPRouterPortDynamicPortList 1.3.6.1.4.1.171.11.64.1.2.10.7.1.4
This object indicates the dynamic portlist of the router port entry.
OBJECT-TYPE    
  PortList  

swL2IGMPRouterPortForbiddenPortList 1.3.6.1.4.1.171.11.64.1.2.10.7.1.5
This object indicates the forbidden portlist of the router port entry.
OBJECT-TYPE    
  PortList  

swL2DhcpRelayMgmt 1.3.6.1.4.1.171.11.64.1.2.11
OBJECT IDENTIFIER    

swL2DhcpRelayState 1.3.6.1.4.1.171.11.64.1.2.11.1
This object indicates if the DHCP relay function is enabled or disabled.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2DhcpRelayHopCount 1.3.6.1.4.1.171.11.64.1.2.11.2
This object indicates the maximum number of router hops that the DHCP packets can cross.
OBJECT-TYPE    
  INTEGER 1..16  

swL2DhcpRelayTimeThreshold 1.3.6.1.4.1.171.11.64.1.2.11.3
This object indicates the minimum time in seconds within which the switch must relay the DHCP request. If this time is exceeded, the switch will drop the DHCP packet.
OBJECT-TYPE    
  INTEGER 0..65535  

swL2DhcpRelayOption82State 1.3.6.1.4.1.171.11.64.1.2.11.4
This object indicates if the DHCP relay agent information option 82 function is enabled or disabled.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2DhcpRelayOption82Check 1.3.6.1.4.1.171.11.64.1.2.11.5
This object indicates if the checking mechanism of DHCP relay agent information option 82 is enabled or disabled.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2DhcpRelayOption82Policy 1.3.6.1.4.1.171.11.64.1.2.11.6
This object indicates the re-forwarding policy is DHCP relay agent information option 82. replace(1) - replace the exiting option 82 field in messages. drop(2) - discard messages with existing option 82 field. keep(3) - retain the existing option 82 field in messages.
OBJECT-TYPE    
  INTEGER replace(1), drop(2), keep(3)  

swL2DhcpRelayCtrlTable 1.3.6.1.4.1.171.11.64.1.2.11.7
This table specifies the IP address og the destination to forward (relay) DHCP packets to.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2DhcpRelayCtrlEntry

swL2DhcpRelayCtrlEntry 1.3.6.1.4.1.171.11.64.1.2.11.7.1
A list of information specifying the IP address as a destination to forward (relay) DHCP packets to.
OBJECT-TYPE    
  SwL2DhcpRelayCtrlEntry  

swL2DhcpRelayCtrlInterfaceName 1.3.6.1.4.1.171.11.64.1.2.11.7.1.1
The name of the IP interface.
OBJECT-TYPE    
  DisplayString SIZE(1..12)  

swL2DhcpRelayCtrlServer 1.3.6.1.4.1.171.11.64.1.2.11.7.1.2
The DHCP server IP address.
OBJECT-TYPE    
  IpAddress  

swL2DhcpRelayCtrlState 1.3.6.1.4.1.171.11.64.1.2.11.7.1.3
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, results in the corresponding entry being removed from the table. valid(3) - this entry will reside in the table.
OBJECT-TYPE    
  INTEGER other(1), invalid(2), valid(3)  

swL2LoopDetectMgmt 1.3.6.1.4.1.171.11.64.1.2.12
OBJECT IDENTIFIER    

swL2LoopDetectCtrl 1.3.6.1.4.1.171.11.64.1.2.12.1
OBJECT IDENTIFIER    

swL2LoopDetectAdminState 1.3.6.1.4.1.171.11.64.1.2.12.1.1
This object indicates the loopback detection status of the system.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swL2LoopDetectInterval 1.3.6.1.4.1.171.11.64.1.2.12.1.2
This object indicates the interval value, the range is from 1 to 32767 seconds.
OBJECT-TYPE    
  INTEGER 1..32767  

swL2LoopDetectRecoverTime 1.3.6.1.4.1.171.11.64.1.2.12.1.3
This object indicates the recover time, the range is from 60 to 1000000. A value of 0 disables the recover function.
OBJECT-TYPE    
  INTEGER 0..1000000  

swL2LoopDetectMode 1.3.6.1.4.1.171.11.64.1.2.12.1.4
This object indicates the loopback detection mode for the system.
OBJECT-TYPE    
  INTEGER vlan-based(1), port-based(2)  

swL2LoopDetectPortMgmt 1.3.6.1.4.1.171.11.64.1.2.12.2
OBJECT IDENTIFIER    

swL2LoopDetectPortTable 1.3.6.1.4.1.171.11.64.1.2.12.2.1
The table specifies the loopback detection function specified by the port.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2LoopDetectPortEntry

swL2LoopDetectPortEntry 1.3.6.1.4.1.171.11.64.1.2.12.2.1.1
The table specifies the loopback detection function specified by the port.
OBJECT-TYPE    
  SwL2LoopDetectPortEntry  

swL2LoopDetectPortIndex 1.3.6.1.4.1.171.11.64.1.2.12.2.1.1.1
This object indicates the module's port number. The range is from 1 to the maximum port number specified in the module
OBJECT-TYPE    
  INTEGER 1..65535  

swL2LoopDetectPortState 1.3.6.1.4.1.171.11.64.1.2.12.2.1.1.2
This object indicates the loopback detection function state on the port.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swL2LoopDetectPortLoopVLAN 1.3.6.1.4.1.171.11.64.1.2.12.2.1.1.3
This object indicates the VLAN list that has detected a loopback.
OBJECT-TYPE    
  DisplayString  

swL2LoopDetectPortLoopStatus 1.3.6.1.4.1.171.11.64.1.2.12.2.1.1.4
This object indicates the port status.
OBJECT-TYPE    
  INTEGER normal(1), loop(2), error(3)  

swL2TrafficSegMgmt 1.3.6.1.4.1.171.11.64.1.2.13
OBJECT IDENTIFIER    

swL2TrafficSegTable 1.3.6.1.4.1.171.11.64.1.2.13.1
This table specifies that the port can just forward traffic to the specific port list.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2TrafficSegEntry

swL2TrafficSegEntry 1.3.6.1.4.1.171.11.64.1.2.13.1.1
A list of information specifying the port with its traffic forward list.
OBJECT-TYPE    
  SwL2TrafficSegEntry  

swL2TrafficSegPort 1.3.6.1.4.1.171.11.64.1.2.13.1.1.1
The port number of the logical port.
OBJECT-TYPE    
  INTEGER 0..65535  

swL2TrafficSegForwardPorts 1.3.6.1.4.1.171.11.64.1.2.13.1.1.2
The port list that the specific port can forward traffic to.
OBJECT-TYPE    
  PortList  

swL2PortSecurityMgmt 1.3.6.1.4.1.171.11.64.1.2.14
OBJECT IDENTIFIER    

swL2PortSecurityControlTable 1.3.6.1.4.1.171.11.64.1.2.14.1
port security feature which controls the address learning capability and the traffic forwarding decision. Each port can have this function enabled or disabled. When it is enabled and a number is given said N, which allows N addresses to be learned at this port, the first N learned addresses are locked at this port as static entry. When the learned addresses number reaches N, any incoming packet that has not learned a source addresses is discarded (e.g. dropped) and no more new addresses can be learned on this port.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2PortSecurityControlEntry

swL2PortSecurityControlEntry 1.3.6.1.4.1.171.11.64.1.2.14.1.1
A list of information contained in swL2PortSecurityControlTable.
OBJECT-TYPE    
  SwL2PortSecurityControlEntry  

swL2PortSecurityPortIndex 1.3.6.1.4.1.171.11.64.1.2.14.1.1.1
Indicates the secured port to lock address learning.
OBJECT-TYPE    
  INTEGER 1..255  

swL2PortSecurityMaxLernAddr 1.3.6.1.4.1.171.11.64.1.2.14.1.1.2
Indicates allowable number of addresses to be learned at this port.
OBJECT-TYPE    
  INTEGER 0..65535  

swL2PortSecurityMode 1.3.6.1.4.1.171.11.64.1.2.14.1.1.3
Indicates the mode of locking address. In deleteOnTimeout(3) mode - the locked addresses can be aged out after aging timer has expired. In this mode, when the locked address has aged out, the number of addresses that can be learned has to increase by one. In deleteOnReset(4) mode - never age out the locked addresses unless restarting the system to prevent from port movement or intrusion.
OBJECT-TYPE    
  INTEGER other(1), permanent(2), deleteOnTimeout(3), deleteOnReset(4)  

swL2PortSecurityAdmState 1.3.6.1.4.1.171.11.64.1.2.14.1.1.4
Indicates the administration state of the locking address.
OBJECT-TYPE    
  INTEGER other(1), enable(2), disable(3)  

swL2PortSecurityTrapLogState 1.3.6.1.4.1.171.11.64.1.2.14.2
when enable(2),whenever there's a new MAC that violates the pre-defined port security configuration, a trap will be sent out and the relevant information will be logged in system.
OBJECT-TYPE    
  INTEGER other(1), enable(2), disable(3)  

swL2MgmtMIBTraps 1.3.6.1.4.1.171.11.64.1.2.15
OBJECT IDENTIFIER    

swL2MgmtMIBTrapPrefix 1.3.6.1.4.1.171.11.64.1.2.15.0
OBJECT IDENTIFIER    

swL2macNotification 1.3.6.1.4.1.171.11.64.1.2.15.0.3
This trap indicate the MAC addresses variation in the address table .
NOTIFICATION-TYPE    
  swL2macNotifyInfo  

swL2porttypechgNotification 1.3.6.1.4.1.171.11.64.1.2.15.0.4
This trap indicates the port type change.
NOTIFICATION-TYPE    
  swL2PortInfoPortIndex  
  swL2PortInfoType  

swPowerStatusChg 1.3.6.1.4.1.171.11.64.1.2.15.0.5
Power Status change notification. The notification is issued when the swPowerStatus changes as in the following cases: lowVoltage -> overCurrent. lowVoltage -> working. lowVoltage -> disconnect. lowVoltage -> connect. overCurrent -> lowVoltage. overCurrent -> working. overCurrent -> disconnect. overCurrent -> connect. working -> lowVoltage. working -> overCurrent. working -> connect. working -> disconnect. fail -> connect. fail -> disconnect. connect -> lowVoltage. connect -> overCurrent. connect -> working. connect -> disconnect. disconnect -> lowVoltage. disconnect -> overCurrent. disconnect -> working. disconnect -> connect.
NOTIFICATION-TYPE    
  swDevInfoPowerUnitIndex  
  swDevInfoPowerID  
  swDevInfoPowerStatus  

swPowerFailure 1.3.6.1.4.1.171.11.64.1.2.15.0.6
Power Failure notification. The notification issues when the swPowerStatus changes as in the following cases: lowVoltage -> fail. overCurrent -> fail. working -> fail. connect -> fail. disconnect -> fail.
NOTIFICATION-TYPE    
  swDevInfoPowerUnitIndex  
  swDevInfoPowerID  
  swDevInfoPowerStatus  

swPowerRecover 1.3.6.1.4.1.171.11.64.1.2.15.0.7
Power Recover notification. The notification issues when the swPowerStatus changes as in the following cases: fail -> lowVoltage. fail -> overCurrent. fail -> working.
NOTIFICATION-TYPE    
  swDevInfoPowerUnitIndex  
  swDevInfoPowerID  
  swDevInfoPowerStatus  

swl2NotificationBidings 1.3.6.1.4.1.171.11.64.1.2.15.1
OBJECT IDENTIFIER    

swL2macNotifyInfo 1.3.6.1.4.1.171.11.64.1.2.15.1.1
This object indicates information about the last time the system rebooted.
OBJECT-TYPE    
  OCTET STRING SIZE(0..1024)  

swl2NotifyPortSecurity 1.3.6.1.4.1.171.11.64.1.2.15.2
OBJECT IDENTIFIER    

swL2PortSecurityViolationMac 1.3.6.1.4.1.171.11.64.1.2.15.2.1
This object indicates the MAC address that violated the port security configuration.
OBJECT-TYPE    
  MacAddress  

swL2PortSecurityViolationTrap 1.3.6.1.4.1.171.11.64.1.2.15.2.2
When the port_security trap is enabled, if there's a new MAC that violates the pre-defined port security configuration a trap will be sent out
NOTIFICATION-TYPE    
  swL2PortSecurityPortIndex  
  swL2PortSecurityViolationMac  

swl2NotifyIpMacBinding 1.3.6.1.4.1.171.11.64.1.2.15.3
OBJECT IDENTIFIER    

swL2IpMacBindingViolationIP 1.3.6.1.4.1.171.11.64.1.2.15.3.1
This object indicates the MAC address that violates the IP-Mac Binging configuration.
OBJECT-TYPE    
  MacAddress  

swL2IpMacBindingViolationMac 1.3.6.1.4.1.171.11.64.1.2.15.3.2
This object indicates the IP address that violates the IP-Mac Binging configuration.
OBJECT-TYPE    
  MacAddress  

swL2IpMacBindingViolationTrap 1.3.6.1.4.1.171.11.64.1.2.15.3.3
When the IP-Mac Binding trap is enabled, if there's a new MAC that violates the pre-defined port security configuration a trap will be sent out
NOTIFICATION-TYPE    
  swL2IpMacBindingPortIndex  
  swL2IpMacBindingViolationIP  
  swL2IpMacBindingViolationMac  

swl2NotifyLoopDetect 1.3.6.1.4.1.171.11.64.1.2.15.4
OBJECT IDENTIFIER    

swL2VlanLoopDetectVID 1.3.6.1.4.1.171.11.64.1.2.15.4.1
This object indicates the VID that has detected a loopback.
OBJECT-TYPE    
  INTEGER  

swL2PortLoopOccurred 1.3.6.1.4.1.171.11.64.1.2.15.4.2
The trap is sent when a Port loop occurs.
NOTIFICATION-TYPE    
  swL2LoopDetectPortIndex  

swL2PortLoopRestart 1.3.6.1.4.1.171.11.64.1.2.15.4.3
The trap is sent when a Port loop restarts after the interval time.
NOTIFICATION-TYPE    
  swL2LoopDetectPortIndex  

swL2VlanLoopOccurred 1.3.6.1.4.1.171.11.64.1.2.15.4.4
The trap is sent when a Port with a VID loop occurs.
NOTIFICATION-TYPE    
  swL2LoopDetectPortIndex  
  swL2VlanLoopDetectVID  

swL2VlanLoopRestart 1.3.6.1.4.1.171.11.64.1.2.15.4.5
The trap is sent when a Port with a VID loop restarts after the interval time.
NOTIFICATION-TYPE    
  swL2LoopDetectPortIndex  
  swL2VlanLoopDetectVID  

swL2DhcpLocalRelayMgmt 1.3.6.1.4.1.171.11.64.1.2.24
OBJECT IDENTIFIER    

swL2DhcpLocalRelayState 1.3.6.1.4.1.171.11.64.1.2.24.1
This object indicates the status of the DHCP local relay function of the switch.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2DhcpLocalRelayVLANTable 1.3.6.1.4.1.171.11.64.1.2.24.2
This table is used to manage the DHCP local relay status for each VLAN.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2DhcpLocalRelayVLANEntry

swL2DhcpLocalRelayVLANEntry 1.3.6.1.4.1.171.11.64.1.2.24.2.1
This object lists the current VLANs in the switch and their corresponding DHCP local relay status.
OBJECT-TYPE    
  SwL2DhcpLocalRelayVLANEntry  

swL2DhcpLocalRelayVLANID 1.3.6.1.4.1.171.11.64.1.2.24.2.1.1
This object shows the VIDs of the current VLANS in the switch.
OBJECT-TYPE    
  INTEGER 1..4094  

swL2DhcpLocalRelayVLANState 1.3.6.1.4.1.171.11.64.1.2.24.2.1.2
This object indicates the status of the DHCP relay function of the VLAN.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

Defined Objects

PortList  
OCTET STRING SIZE(0..127)    

VlanIndex  
Unsigned32    

VlanId  
INTEGER 1..4094    

SwDevInfoPowerEntry  
SEQUENCE    
  INTEGER as swDevInfoPowerUnitIndex  
  INTEGER as swDevInfoPowerID  
  INTEGER as swDevInfoPowerStatus  

SwL2VlanAdvertisementEntry  
SEQUENCE    
  INTEGER as swL2VlanIndex  
  DisplayString as swL2VlanName  
  INTEGER as swL2VlanAdvertiseState  

SwL2PortInfoEntry  
SEQUENCE    
  INTEGER as swL2PortInfoPortIndex  
  INTEGER as swL2PortInfoUnitIndex  
  INTEGER as swL2PortInfoType  
  INTEGER as swL2PortInfoLinkStatus  
  INTEGER as swL2PortInfoNwayStatus  
  INTEGER as swL2PortInfoModuleType  
  INTEGER as swL2PortInfoErrorDisabled  

SwL2PortCtrlEntry  
SEQUENCE    
  INTEGER as swL2PortCtrlPortIndex  
  INTEGER as swL2PortCtrlUnitIndex  
  INTEGER as swL2PortCtrlAdminState  
  INTEGER as swL2PortCtrlNwayState  
  INTEGER as swL2PortCtrlFlowCtrlState  
  INTEGER as swL2PortCtrlLockState  
  INTEGER as swL2PortCtrlMACNotifyState  
  INTEGER as swL2PortCtrlMulticastfilter  
  INTEGER as swL2PortCtrlMdixState  

SwL2PortInformationEntry  
SEQUENCE    
  INTEGER as swL2PortInformationPortIndex  
  INTEGER as swL2PortInformationMediumType  
  INTEGER as swL2PortInformationUnitID  
  INTEGER as swL2PortInformationType  
  INTEGER as swL2PortInformationLinkStatus  
  INTEGER as swL2PortInformationNwayStatus  
  INTEGER as swL2PortInformationModuleType  
  INTEGER as swL2PortInformationErrorDisabled  

SwL2PortControlEntry  
SEQUENCE    
  INTEGER as swL2PortControlPortIndex  
  INTEGER as swL2PortControlMediumType  
  INTEGER as swL2PortControlUnitIndex  
  INTEGER as swL2PortControlAdminState  
  INTEGER as swL2PortControlNwayState  
  INTEGER as swL2PortControlFlowCtrlState  
  INTEGER as swL2PortControlLockState  
  INTEGER as swL2PortControlMACNotifyState  
  INTEGER as swL2PortControlMulticastfilter  
  INTEGER as swL2PortControlMdixState  

SwL2MulticastRangeEntry  
SEQUENCE    
  DisplayString as swL2MulticastRangeName  
  IpAddress as swL2MulticastRangeFromIp  
  IpAddress as swL2MulticastRangeToIp  
  RowStatus as swL2MulticastRangeRowStatus  

SwL2LimitedMulticastStatusEntry  
SEQUENCE    
  INTEGER as swL2LimitedMulticastPort  
  INTEGER as swL2LimitedMulticastAccess  
  INTEGER as swL2LimitedMulticastState  

SwL2LimitedMulticastRangeEntry  
SEQUENCE    
  INTEGER as swL2LimitedMulticastID  
  DisplayString as swL2LimitedMulticastRangeName  
  IpAddress as swL2LimitedMulticastFromIp  
  IpAddress as swL2LimitedMulticastToIp  
  RowStatus as swL2LimitedMulticastRowStatus  

SwL2QOSBandwidthControlEntry  
SEQUENCE    
  INTEGER as swL2QOSBandwidthPortIndex  
  INTEGER as swL2QOSBandwidthRxRate  
  INTEGER as swL2QOSBandwidthTxRate  
  INTEGER as swL2QOSBandwidthRadiusRxRate  
  INTEGER as swL2QOSBandwidthRadiusTxRate  

SwL2QOSSchedulingEntry  
SEQUENCE    
  INTEGER as swL2QOSSchedulingClassIndex  
  INTEGER as swL2QOSSchedulingMaxPkts  
  INTEGER as swL2QOSSchedulingMaxLatency  

SwL2QOS8021pUserPriorityEntry  
SEQUENCE    
  INTEGER as swL2QOS8021pUserPriorityIndex  
  INTEGER as swL2QOS8021pUserPriorityClass  

SwL2QOS8021pDefaultPriorityEntry  
SEQUENCE    
  INTEGER as swL2QOS8021pDefaultPriorityIndex  
  INTEGER as swL2QOS8021pDefaultPriority  
  INTEGER as swL2QOS8021pRadiusPriority  

SwL2IpMacBindingPortEntry  
SEQUENCE    
  INTEGER as swL2IpMacBindingPortIndex  
  INTEGER as swL2IpMacBindingPortState  
  INTEGER as swL2IpMacBindingPortAllowZeroIp  
  INTEGER as swL2IpMacBindingPortForwardDhcpPkt  
  INTEGER as swL2IpMacBindingPortDHCPSnoopMaxEntry  
  INTEGER as swL2IpMacBindingPortDHCPSnoopEntryClearAction  

SwL2IpMacBindingEntry  
SEQUENCE    
  IpAddress as swL2IpMacBindingIpIndex  
  MacAddress as swL2IpMacBindingMac  
  RowStatus as swL2IpMacBindingStatus  
  PortList as swL2IpMacBindingPorts  
  INTEGER as swL2IpMacBindingAction  
  INTEGER as swL2IpMacBindingMode  

SwL2IpMacBindingBlockedEntry  
SEQUENCE    
  VlanIndex as swL2IpMacBindingBlockedVID  
  MacAddress as swL2IpMacBindingBlockedMac  
  DisplayString as swL2IpMacBindingBlockedVlanName  
  INTEGER as swL2IpMacBindingBlockedPort  
  INTEGER as swL2IpMacBindingBlockedType  

SwL2IpMacBindingDHCPSnoopEntry  
SEQUENCE    
  IpAddress as swL2IpMacBindingDHCPSnoopIpIndex  
  MacAddress as swL2IpMacBindingDHCPSnoopMac  
  INTEGER as swL2IpMacBindingDHCPSnoopLeaseTime  
  INTEGER as swL2IpMacBindingDHCPSnoopPort  
  INTEGER as swL2IpMacBindingDHCPSnoopStatus  

SwL2IpMacBindingPermitIPPoolEntry  
SEQUENCE    
  IpAddress as swL2IpMacBindingPermitIPPoolStartIP  
  IpAddress as swL2IpMacBindingPermitIPPoolEndIP  
  PortList as swL2IpMacBindingPermitIPPoolPorts  
  RowStatus as swL2IpMacBindingPermitIPPoolStatus  

SwL2TrunkCtrlEntry  
SEQUENCE    
  INTEGER as swL2TrunkIndex  
  DisplayString as swL2TrunkName  
  INTEGER as swL2TrunkMasterPort  
  PortList as swL2TrunkMember  
  INTEGER as swL2TrunkFloodingPort  
  INTEGER as swL2TrunkType  
  RowStatus as swL2TrunkState  

SwL2IGMPCtrlEntry  
SEQUENCE    
  INTEGER as swL2IGMPCtrlVid  
  INTEGER as swL2IGMPQueryInterval  
  INTEGER as swL2IGMPMaxResponseTime  
  INTEGER as swL2IGMPRobustness  
  INTEGER as swL2IGMPLastMemberQueryInterval  
  INTEGER as swL2IGMPHostTimeout  
  INTEGER as swL2IGMPRouteTimeout  
  INTEGER as swL2IGMPLeaveTimer  
  INTEGER as swL2IGMPQueryState  
  INTEGER as swL2IGMPCurrentState  
  INTEGER as swL2IGMPCtrlState  

SwL2IGMPQueryInfoEntry  
SEQUENCE    
  INTEGER as swL2IGMPInfoVid  
  INTEGER as swL2IGMPInfoQueryCount  
  INTEGER as swL2IGMPInfoTxQueryCount  

SwL2IGMPInfoEntry  
SEQUENCE    
  INTEGER as swL2IGMPVid  
  IpAddress as swL2IGMPGroupIpAddr  
  MacAddress as swL2IGMPMacAddr  
  PortList as swL2IGMPPortMap  
  INTEGER as swL2IGMPIpGroupReportCount  

SwL2IGMPMulticastVlanEntry  
SEQUENCE    
  INTEGER as swL2IGMPMulticastVlanid  
  SnmpAdminString as swL2IGMPMulticastVlanName  
  PortList as swL2IGMPMulticastVlanSourcePort  
  PortList as swL2IGMPMulticastVlanMemberPort  
  RowStatus as swL2IGMPMulticastVlanRowStatus  
  IpAddress as swL2IGMPMulticastVlanReplaceSourceIP  

SwL2IGMPRouterPortEntry  
SEQUENCE    
  INTEGER as swL2IGMPRouterPortVlanid  
  SnmpAdminString as swL2IGMPRouterPortVlanName  
  PortList as swL2IGMPRouterPortStaticPortList  
  PortList as swL2IGMPRouterPortDynamicPortList  
  PortList as swL2IGMPRouterPortForbiddenPortList  

SwL2DhcpRelayCtrlEntry  
SEQUENCE    
  DisplayString as swL2DhcpRelayCtrlInterfaceName  
  IpAddress as swL2DhcpRelayCtrlServer  
  INTEGER as swL2DhcpRelayCtrlState  

SwL2LoopDetectPortEntry  
SEQUENCE    
  INTEGER as swL2LoopDetectPortIndex  
  INTEGER as swL2LoopDetectPortState  
  DisplayString as swL2LoopDetectPortLoopVLAN  
  INTEGER as swL2LoopDetectPortLoopStatus  

SwL2TrafficSegEntry  
SEQUENCE    
  INTEGER as swL2TrafficSegPort  
  PortList as swL2TrafficSegForwardPorts  

SwL2PortSecurityControlEntry  
SEQUENCE    
  INTEGER as swL2PortSecurityPortIndex  
  INTEGER as swL2PortSecurityMaxLernAddr  
  INTEGER as swL2PortSecurityMode  
  INTEGER as swL2PortSecurityAdmState  

SwL2DhcpLocalRelayVLANEntry  
SEQUENCE    
  INTEGER as swL2DhcpLocalRelayVLANID  
  INTEGER as swL2DhcpLocalRelayVLANState