DISMAN-TRACEROUTE-MIB

File: DISMAN-TRACEROUTE-MIB.mib (50668 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
SNMP-FRAMEWORK-MIB IF-MIB INET-ADDRESS-MIB
DISMAN-PING-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Integer32
Gauge32 Unsigned32 mib-2
NOTIFICATION-TYPE OBJECT-IDENTITY RowStatus
StorageType TruthValue DateAndTime
MODULE-COMPLIANCE OBJECT-GROUP NOTIFICATION-GROUP
SnmpAdminString InterfaceIndexOrZero InetAddressType
InetAddress OperationResponseStatus

Defined Objects

traceRouteMIB 1.3.6.1.2.1.81
The Traceroute MIB (DISMAN-TRACEROUTE-MIB) provides access to the traceroute capability at a remote host.
MODULE-IDENTITY    

traceRouteNotifications 1.3.6.1.2.1.81.0
OBJECT IDENTIFIER    

traceRoutePathChange 1.3.6.1.2.1.81.0.1
The path to a target has changed.
NOTIFICATION-TYPE    
  traceRouteCtlTargetAddressType  
  traceRouteCtlTargetAddress  
  traceRouteResultsIpTgtAddrType  
  traceRouteResultsIpTgtAddr  

traceRouteTestFailed 1.3.6.1.2.1.81.0.2
Could not determine the path to a target.
NOTIFICATION-TYPE    
  traceRouteCtlTargetAddressType  
  traceRouteCtlTargetAddress  
  traceRouteResultsIpTgtAddrType  
  traceRouteResultsIpTgtAddr  

traceRouteTestCompleted 1.3.6.1.2.1.81.0.3
The path to a target has just been determined.
NOTIFICATION-TYPE    
  traceRouteCtlTargetAddressType  
  traceRouteCtlTargetAddress  
  traceRouteResultsIpTgtAddrType  
  traceRouteResultsIpTgtAddr  

traceRouteObjects 1.3.6.1.2.1.81.1
OBJECT IDENTIFIER    

traceRouteMaxConcurrentRequests 1.3.6.1.2.1.81.1.1
The maximum number of concurrent active traceroute requests that are allowed within an agent implementation. A value of 0 for this object implies that there is no limit for the number of concurrent active requests in effect.
OBJECT-TYPE    
  Unsigned32  

traceRouteCtlTable 1.3.6.1.2.1.81.1.2
Defines the Remote Operations Traceroute Control Table for providing the capability of invoking traceroute from a remote host. The results of traceroute operations can be stored in the traceRouteResultsTable, traceRouteProbeHistoryTable, and the traceRouteHopsTable.
OBJECT-TYPE    
  SEQUENCE OF  
    TraceRouteCtlEntry

traceRouteCtlEntry 1.3.6.1.2.1.81.1.2.1
Defines an entry in the traceRouteCtlTable. The first index element, traceRouteCtlOwnerIndex, is of type SnmpAdminString, a textual convention that allows for use of the SNMPv3 View-Based Access Control Model (RFC 2575 [11], VACM) and allows an management application to identify its entries. The second index, traceRouteCtlTestName (also an SnmpAdminString), enables the same management application to have multiple requests outstanding.
OBJECT-TYPE    
  TraceRouteCtlEntry  

traceRouteCtlOwnerIndex 1.3.6.1.2.1.81.1.2.1.1
To facilitate the provisioning of access control by a security administrator using the View-Based Access Control Model (RFC 2575, VACM) for tables in which multiple users may need to independently create or modify entries, the initial index is used as an 'owner index'. Such an initial index has a syntax of SnmpAdminString, and can thus be trivially mapped to a securityName or groupName as defined in VACM, in accordance with a security policy. When used in conjunction with such a security policy all entries in the table belonging to a particular user (or group) will have the same value for this initial index. For a given user's entries in a particular table, the object identifiers for the information in these entries will have the same subidentifiers (except for the 'column' subidentifier) up to the end of the encoded owner index. To configure VACM to permit access to this portion of the table, one would create vacmViewTreeFamilyTable entries with the value of vacmViewTreeFamilySubtree including the owner index portion, and vacmViewTreeFamilyMask 'wildcarding' the column subidentifier. More elaborate configurations are possible.
OBJECT-TYPE    
  SnmpAdminString SIZE(0..32)  

traceRouteCtlTestName 1.3.6.1.2.1.81.1.2.1.2
The name of a traceroute test. This is locally unique, within the scope of an traceRouteCtlOwnerIndex.
OBJECT-TYPE    
  SnmpAdminString SIZE(0..32)  

traceRouteCtlTargetAddressType 1.3.6.1.2.1.81.1.2.1.3
Specifies the type of host address to be used on the traceroute request at the remote host.
OBJECT-TYPE    
  InetAddressType  

traceRouteCtlTargetAddress 1.3.6.1.2.1.81.1.2.1.4
Specifies the host address used on the traceroute request at the remote host. The host address type can be determined by the examining the value of the corresponding traceRouteCtlTargetAddressType index element. A value for this object MUST be set prior to transitioning its corresponding traceRouteCtlEntry to active(1) via traceRouteCtlRowStatus.
OBJECT-TYPE    
  InetAddress  

traceRouteCtlByPassRouteTable 1.3.6.1.2.1.81.1.2.1.5
The purpose of this object is to optionally enable bypassing the route table. If enabled, the remote host will bypass the normal routing tables and send directly to a host on an attached network. If the host is not on a directly-attached network, an error is returned. This option can be used to perform the traceroute operation to a local host through an interface that has no route defined (e.g., after the interface was dropped by routed).
OBJECT-TYPE    
  TruthValue  

traceRouteCtlDataSize 1.3.6.1.2.1.81.1.2.1.6
Specifies the size of the data portion of a traceroute request in octets. A traceroute request is essentially transmitted by encoding a UDP datagram into a IP packet. So subtracting the size of a UDP header (8 octets) and the size of a IP header (20 octets) yields a maximum of 65507 octets.
OBJECT-TYPE    
  Unsigned32 0..65507  

traceRouteCtlTimeOut 1.3.6.1.2.1.81.1.2.1.7
Specifies the time-out value, in seconds, for a traceroute request.
OBJECT-TYPE    
  Unsigned32 1..60  

traceRouteCtlProbesPerHop 1.3.6.1.2.1.81.1.2.1.8
Specifies the number of times to reissue a traceroute request with the same time-to-live (TTL) value.
OBJECT-TYPE    
  Unsigned32 1..10  

traceRouteCtlPort 1.3.6.1.2.1.81.1.2.1.9
Specifies the UDP port to send the traceroute request to. Need to specify a port that is not in use at the destination (target) host. The default value for this object is the IANA assigned port, 33434, for the traceroute function.
OBJECT-TYPE    
  Unsigned32 1..65535  

traceRouteCtlMaxTtl 1.3.6.1.2.1.81.1.2.1.10
Specifies the maximum time-to-live value.
OBJECT-TYPE    
  Unsigned32 1..255  

traceRouteCtlDSField 1.3.6.1.2.1.81.1.2.1.11
Specifies the value to store in the Differentiated Services (DS) Field in the IP packet used to encapsulate the traceroute probe. The DS Field is defined as the Type of Service (TOS) octet in a IPv4 header or as the Traffic Class octet in a IPv6 header. The value of this object must be a decimal integer in the range from 0 to 255. This option can be used to determine what effect an explicit DS Field setting has on a traceroute response. Not all values are legal or meaningful. DS Field usage is often not supported by IP implementations. A value of 0 means that the function represented by this option is not supported. Useful TOS octet values are probably '16' (low delay) and '8' ( high throughput).
OBJECT-TYPE    
  Unsigned32 0..255  

traceRouteCtlSourceAddressType 1.3.6.1.2.1.81.1.2.1.12
Specifies the type of the source address, traceRouteCtlSourceAddress, to be used at a remote host when performing a traceroute operation.
OBJECT-TYPE    
  InetAddressType  

traceRouteCtlSourceAddress 1.3.6.1.2.1.81.1.2.1.13
Use the specified IP address (which must be given as an IP number, not a hostname) as the source address in outgoing probe packets. On hosts with more than one IP address, this option can be used to force the source address to be something other than the primary IP address of the interface the probe packet is sent on. If the IP address is not one of this machine's interface addresses, an error is returned and nothing is sent. A zero length octet string value for this object disables source address specification. The address type (InetAddressType) that relates to this object is specified by the corresponding value of traceRouteCtlSourceAddressType.
OBJECT-TYPE    
  InetAddress  

traceRouteCtlIfIndex 1.3.6.1.2.1.81.1.2.1.14
Setting this object to an interface's ifIndex prior to starting a remote traceroute operation directs the traceroute probes to be transmitted over the specified interface. A value of zero for this object implies that this option is not enabled.
OBJECT-TYPE    
  InterfaceIndexOrZero  

traceRouteCtlMiscOptions 1.3.6.1.2.1.81.1.2.1.15
Enables an application to specify implementation dependent options.
OBJECT-TYPE    
  SnmpAdminString  

traceRouteCtlMaxFailures 1.3.6.1.2.1.81.1.2.1.16
The value of this object indicates the maximum number of consecutive timeouts allowed before terminating a remote traceroute request. A value of either 255 (maximum hop count/possible TTL value) or a 0 indicates that the function of terminating a remote traceroute request when a specific number of successive timeouts are detected is disabled.
OBJECT-TYPE    
  Unsigned32 0..255  

traceRouteCtlDontFragment 1.3.6.1.2.1.81.1.2.1.17
This object enables setting of the don't fragment flag (DF) in the IP header for a probe. Use of this object enables performing a manual PATH MTU test.
OBJECT-TYPE    
  TruthValue  

traceRouteCtlInitialTtl 1.3.6.1.2.1.81.1.2.1.18
The value of this object specifies the initial TTL value to use. This enables bypassing the initial (often well known) portion of a path.
OBJECT-TYPE    
  Unsigned32 0..255  

traceRouteCtlFrequency 1.3.6.1.2.1.81.1.2.1.19
The number of seconds to wait before repeating a traceroute test as defined by the value of the various objects in the corresponding row. The number of hops in a single traceroute test is determined by the value of the corresponding traceRouteCtlProbesPerHop object. After a single test completes the number of seconds as defined by the value of traceRouteCtlFrequency MUST elapse before the next traceroute test is started. A value of 0 for this object implies that the test as defined by the corresponding entry will not be repeated.
OBJECT-TYPE    
  Unsigned32  

traceRouteCtlStorageType 1.3.6.1.2.1.81.1.2.1.20
The storage type for this conceptual row. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row.
OBJECT-TYPE    
  StorageType  

traceRouteCtlAdminStatus 1.3.6.1.2.1.81.1.2.1.21
Reflects the desired state that an traceRouteCtlEntry should be in: enabled(1) - Attempt to activate the test as defined by this traceRouteCtlEntry. disabled(2) - Deactivate the test as defined by this traceRouteCtlEntry. Refer to the corresponding traceRouteResultsOperStatus to determine the operational state of the test defined by this entry.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

traceRouteCtlDescr 1.3.6.1.2.1.81.1.2.1.22
The purpose of this object is to provide a descriptive name of the remote traceroute test.
OBJECT-TYPE    
  SnmpAdminString  

traceRouteCtlMaxRows 1.3.6.1.2.1.81.1.2.1.23
The maximum number of entries allowed in the traceRouteProbeHistoryTable. An implementation of this MIB will remove the oldest entry in the traceRouteProbeHistoryTable to allow the addition of an new entry once the number of rows in the traceRouteProbeHistoryTable reaches this value. Old entries are not removed when a new test is started. Entries are added to the traceRouteProbeHistoryTable until traceRouteCtlMaxRows is reached before entries begin to be removed. A value of 0 for this object disables creation of traceRouteProbeHistoryTable entries.
OBJECT-TYPE    
  Unsigned32  

traceRouteCtlTrapGeneration 1.3.6.1.2.1.81.1.2.1.24
The value of this object determines when and if to to generate a notification for this entry: pathChange(0) - Generate a traceRoutePathChange notification when the current path varies from a previously determined path. testFailure(1) - Generate a traceRouteTestFailed notification when the full path to a target can't be determined. testCompletion(2) - Generate a traceRouteTestCompleted notification when the path to a target has been determined. The value of this object defaults to zero, indicating that none of the above options have been selected.
OBJECT-TYPE    
  BITS pathChange(0), testFailure(1), testCompletion(2)  

traceRouteCtlCreateHopsEntries 1.3.6.1.2.1.81.1.2.1.25
The current path for a traceroute test is kept in the traceRouteHopsTable on a per hop basis when the value of this object is true(1).
OBJECT-TYPE    
  TruthValue  

traceRouteCtlType 1.3.6.1.2.1.81.1.2.1.26
The value of this object is used either to report or select the implementation method to be used for performing a traceroute operation. The value of this object may be selected from traceRouteImplementationTypeDomains. Additional implementation types should be allocated as required by implementers of the DISMAN-TRACEROUTE-MIB under their enterprise specific registration point and not beneath traceRouteImplementationTypeDomains.
OBJECT-TYPE    
  OBJECT IDENTIFIER  

traceRouteCtlRowStatus 1.3.6.1.2.1.81.1.2.1.27
This object allows entries to be created and deleted in the traceRouteCtlTable. Deletion of an entry in this table results in all corresponding (same traceRouteCtlOwnerIndex and traceRouteCtlTestName index values) traceRouteResultsTable, traceRouteProbeHistoryTable, and traceRouteHopsTable entries being deleted. A value MUST be specified for traceRouteCtlTargetAddress prior to a transition to active(1) state being accepted. Activation of a remote traceroute operation is controlled via traceRouteCtlAdminStatus and not by transitioning of this object's value to active(1). Transitions in and out of active(1) state are not allowed while an entry's traceRouteResultsOperStatus is active(1) with the exception that deletion of an entry in this table by setting its RowStatus object to destroy(6) will stop an active traceroute operation. The operational state of an traceroute operation can be determined by examination of the corresponding traceRouteResultsOperStatus object.
OBJECT-TYPE    
  RowStatus  

traceRouteResultsTable 1.3.6.1.2.1.81.1.3
Defines the Remote Operations Traceroute Results Table for keeping track of the status of a traceRouteCtlEntry. An entry is added to the traceRouteResultsTable when an traceRouteCtlEntry is started by successful transition of its traceRouteCtlAdminStatus object to enabled(1). An entry is removed from the traceRouteResultsTable when its corresponding traceRouteCtlEntry is deleted.
OBJECT-TYPE    
  SEQUENCE OF  
    TraceRouteResultsEntry

traceRouteResultsEntry 1.3.6.1.2.1.81.1.3.1
Defines an entry in the traceRouteResultsTable. The traceRouteResultsTable has the same indexing as the traceRouteCtlTable in order for a traceRouteResultsEntry to correspond to the traceRouteCtlEntry that caused it to be created.
OBJECT-TYPE    
  TraceRouteResultsEntry  

traceRouteResultsOperStatus 1.3.6.1.2.1.81.1.3.1.1
Reflects the operational state of an traceRouteCtlEntry: enabled(1) - Test is active. disabled(2) - Test has stopped.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

traceRouteResultsCurHopCount 1.3.6.1.2.1.81.1.3.1.2
Reflects the current TTL value (range from 1 to 255) for a remote traceroute operation. Maximum TTL value is determined by traceRouteCtlMaxTtl.
OBJECT-TYPE    
  Gauge32  

traceRouteResultsCurProbeCount 1.3.6.1.2.1.81.1.3.1.3
Reflects the current probe count (1..10) for a remote traceroute operation. The maximum probe count is determined by traceRouteCtlProbesPerHop.
OBJECT-TYPE    
  Gauge32  

traceRouteResultsIpTgtAddrType 1.3.6.1.2.1.81.1.3.1.4
This objects indicates the type of address stored in the corresponding traceRouteResultsIpTgtAddr object.
OBJECT-TYPE    
  InetAddressType  

traceRouteResultsIpTgtAddr 1.3.6.1.2.1.81.1.3.1.5
This objects reports the IP address associated with a traceRouteCtlTargetAddress value when the destination address is specified as a DNS name. The value of this object should be a zero length octet string when a DNS name is not specified or when a specified DNS name fails to resolve.
OBJECT-TYPE    
  InetAddress  

traceRouteResultsTestAttempts 1.3.6.1.2.1.81.1.3.1.6
The current number of attempts to determine a path to a target. The value of this object MUST be started at 0.
OBJECT-TYPE    
  Unsigned32  

traceRouteResultsTestSuccesses 1.3.6.1.2.1.81.1.3.1.7
The current number of attempts to determine a path to a target that have succeeded. The value of this object MUST be reported as 0 when no attempts have succeeded.
OBJECT-TYPE    
  Unsigned32  

traceRouteResultsLastGoodPath 1.3.6.1.2.1.81.1.3.1.8
The date and time when the last complete path was determined.
OBJECT-TYPE    
  DateAndTime  

traceRouteProbeHistoryTable 1.3.6.1.2.1.81.1.4
Defines the Remote Operations Traceroute Results Table for storing the results of a traceroute operation. An implementation of this MIB will remove the oldest entry in the traceRouteProbeHistoryTable to allow the addition of an new entry once the number of rows in the traceRouteProbeHistoryTable reaches the value specified by traceRouteCtlMaxRows.
OBJECT-TYPE    
  SEQUENCE OF  
    TraceRouteProbeHistoryEntry

traceRouteProbeHistoryEntry 1.3.6.1.2.1.81.1.4.1
Defines a table for storing the results of a traceroute operation. Entries in this table are limited by the value of the corresponding traceRouteCtlMaxRows object. The first two index elements identify the traceRouteCtlEntry that a traceRouteProbeHistoryEntry belongs to. The third index element selects a single traceroute operation result. The fourth and fifth indexes select the hop and the probe for a particular traceroute operation.
OBJECT-TYPE    
  TraceRouteProbeHistoryEntry  

traceRouteProbeHistoryIndex 1.3.6.1.2.1.81.1.4.1.1
An entry in this table is created when the result of a traceroute probe is determined. The initial 2 instance identifier index values identify the traceRouteCtlEntry that a probe result (traceRouteProbeHistoryEntry) belongs to. An entry is removed from this table when its corresponding traceRouteCtlEntry is deleted. An implementation MUST start assigning traceRouteProbeHistoryIndex values at 1 and wrap after exceeding the maximum possible value as defined by the limit of this object ('ffffffff'h).
OBJECT-TYPE    
  Unsigned32 1..'ffffffff'h  

traceRouteProbeHistoryHopIndex 1.3.6.1.2.1.81.1.4.1.2
Indicates which hop in a traceroute path that the probe's results are for. The value of this object is initially determined by the value of traceRouteCtlInitialTtl.
OBJECT-TYPE    
  Unsigned32 1..255  

traceRouteProbeHistoryProbeIndex 1.3.6.1.2.1.81.1.4.1.3
Indicates the index of a probe for a particular hop in a traceroute path. The number of probes per hop is determined by the value of the corresponding traceRouteCtlProbesPerHop object.
OBJECT-TYPE    
  Unsigned32 1..10  

traceRouteProbeHistoryHAddrType 1.3.6.1.2.1.81.1.4.1.4
This objects indicates the type of address stored in the corresponding traceRouteProbeHistoryHAddr object.
OBJECT-TYPE    
  InetAddressType  

traceRouteProbeHistoryHAddr 1.3.6.1.2.1.81.1.4.1.5
The address of a hop in a traceroute path. This object is not allowed to be a DNS name. The value of the corresponding object, traceRouteProbeHistoryHAddrType, indicates this object's IP address type.
OBJECT-TYPE    
  InetAddress  

traceRouteProbeHistoryResponse 1.3.6.1.2.1.81.1.4.1.6
The amount of time measured in milliseconds from when a probe was sent to when its response was received or when it timed out. The value of this object is reported as 0 when it is not possible to transmit a probe.
OBJECT-TYPE    
  Unsigned32  

traceRouteProbeHistoryStatus 1.3.6.1.2.1.81.1.4.1.7
The result of a traceroute operation made by a remote host for a particular probe.
OBJECT-TYPE    
  OperationResponseStatus  

traceRouteProbeHistoryLastRC 1.3.6.1.2.1.81.1.4.1.8
The last implementation method specific reply code received. Traceroute is usually implemented by transmitting a series of probe packets with increasing time-to-live values. A probe packet is a UDP datagram encapsulated into an IP packet. Each hop in a path to the target (destination) host rejects the probe packets (probe's TTL too small, ICMP reply) until either the maximum TTL is exceeded or the target host is received.
OBJECT-TYPE    
  Integer32  

traceRouteProbeHistoryTime 1.3.6.1.2.1.81.1.4.1.9
Timestamp for when this probe results were determined.
OBJECT-TYPE    
  DateAndTime  

traceRouteHopsTable 1.3.6.1.2.1.81.1.5
Defines the Remote Operations Traceroute Hop Table for keeping track of the results of traceroute tests on a per hop basis.
OBJECT-TYPE    
  SEQUENCE OF  
    TraceRouteHopsEntry

traceRouteHopsEntry 1.3.6.1.2.1.81.1.5.1
Defines an entry in the traceRouteHopsTable. The first two index elements identify the traceRouteCtlEntry that a traceRouteHopsEntry belongs to. The third index element, traceRouteHopsHopIndex, selects a hop in a traceroute path.
OBJECT-TYPE    
  TraceRouteHopsEntry  

traceRouteHopsHopIndex 1.3.6.1.2.1.81.1.5.1.1
Specifies the hop index for a traceroute hop. Values for this object with respect to the same traceRouteCtlOwnerIndex and traceRouteCtlTestName MUST start at 1 and increase monotonically. The traceRouteHopsTable keeps the current traceroute path per traceRouteCtlEntry if enabled by setting the corresponding traceRouteCtlCreateHopsEntries to true(1). All hops (traceRouteHopsTable entries) in a traceroute path MUST be updated at the same time when a traceroute operation completes. Care needs to be applied when either a path changes or can't be determined. The initial portion of the path, up to the first hop change, MUST retain the same traceRouteHopsHopIndex values. The remaining portion of the path SHOULD be assigned new traceRouteHopsHopIndex values.
OBJECT-TYPE    
  Unsigned32  

traceRouteHopsIpTgtAddressType 1.3.6.1.2.1.81.1.5.1.2
This objects indicates the type of address stored in the corresponding traceRouteHopsIpTargetAddress object.
OBJECT-TYPE    
  InetAddressType  

traceRouteHopsIpTgtAddress 1.3.6.1.2.1.81.1.5.1.3
This object reports the IP address associated with the hop. A value for this object should be reported as a numeric IP address and not as a DNS name.
OBJECT-TYPE    
  InetAddress  

traceRouteHopsMinRtt 1.3.6.1.2.1.81.1.5.1.4
The minimum traceroute round-trip-time (RTT) received for this hop. A value of 0 for this object implies that no RTT has been received.
OBJECT-TYPE    
  Unsigned32  

traceRouteHopsMaxRtt 1.3.6.1.2.1.81.1.5.1.5
The maximum traceroute round-trip-time (RTT) received for this hop. A value of 0 for this object implies that no RTT has been received.
OBJECT-TYPE    
  Unsigned32  

traceRouteHopsAverageRtt 1.3.6.1.2.1.81.1.5.1.6
The current average traceroute round-trip-time (RTT) for this hop.
OBJECT-TYPE    
  Unsigned32  

traceRouteHopsRttSumOfSquares 1.3.6.1.2.1.81.1.5.1.7
This object contains the sum of all traceroute responses received for this hop. Its purpose is to enable standard deviation calculation.
OBJECT-TYPE    
  Unsigned32  

traceRouteHopsSentProbes 1.3.6.1.2.1.81.1.5.1.8
The value of this object reflects the number of probes sent for this hop during this traceroute test. The value of this object should start at 0.
OBJECT-TYPE    
  Unsigned32  

traceRouteHopsProbeResponses 1.3.6.1.2.1.81.1.5.1.9
Number of responses received for this hop during this traceroute test. This value of this object should start at 0.
OBJECT-TYPE    
  Unsigned32  

traceRouteHopsLastGoodProbe 1.3.6.1.2.1.81.1.5.1.10
Date and time was the last response was received for a probe for this hop during this traceroute test.
OBJECT-TYPE    
  DateAndTime  

traceRouteConformance 1.3.6.1.2.1.81.2
OBJECT IDENTIFIER    

traceRouteCompliances 1.3.6.1.2.1.81.2.1
OBJECT IDENTIFIER    

traceRouteCompliance 1.3.6.1.2.1.81.2.1.1
The compliance statement for the DISMAN-TRACEROUTE-MIB.
MODULE-COMPLIANCE    

traceRouteGroups 1.3.6.1.2.1.81.2.2
OBJECT IDENTIFIER    

traceRouteGroup 1.3.6.1.2.1.81.2.2.1
The group of objects that comprise the remote traceroute operation.
OBJECT-GROUP    

traceRouteTimeStampGroup 1.3.6.1.2.1.81.2.2.2
The group of DateAndTime objects.
OBJECT-GROUP    

traceRouteNotificationsGroup 1.3.6.1.2.1.81.2.2.3
The notifications which are required to be supported by implementations of this MIB.
NOTIFICATION-GROUP    

traceRouteHopsTableGroup 1.3.6.1.2.1.81.2.2.4
The group of objects that comprise the traceRouteHopsTable.
OBJECT-GROUP    

traceRouteImplementationTypeDomains 1.3.6.1.2.1.81.3
OBJECT IDENTIFIER    

traceRouteUsingUdpProbes 1.3.6.1.2.1.81.3.1
Indicates that an implementation is using UDP probes to perform the traceroute operation.
OBJECT-IDENTITY    

Defined Objects

TraceRouteCtlEntry  
SEQUENCE    
  SnmpAdminString as traceRouteCtlOwnerIndex  
  SnmpAdminString as traceRouteCtlTestName  
  InetAddressType as traceRouteCtlTargetAddressType  
  InetAddress as traceRouteCtlTargetAddress  
  TruthValue as traceRouteCtlByPassRouteTable  
  Unsigned32 as traceRouteCtlDataSize  
  Unsigned32 as traceRouteCtlTimeOut  
  Unsigned32 as traceRouteCtlProbesPerHop  
  Unsigned32 as traceRouteCtlPort  
  Unsigned32 as traceRouteCtlMaxTtl  
  Unsigned32 as traceRouteCtlDSField  
  InetAddressType as traceRouteCtlSourceAddressType  
  InetAddress as traceRouteCtlSourceAddress  
  InterfaceIndexOrZero as traceRouteCtlIfIndex  
  SnmpAdminString as traceRouteCtlMiscOptions  
  Unsigned32 as traceRouteCtlMaxFailures  
  TruthValue as traceRouteCtlDontFragment  
  Unsigned32 as traceRouteCtlInitialTtl  
  Unsigned32 as traceRouteCtlFrequency  
  StorageType as traceRouteCtlStorageType  
  INTEGER as traceRouteCtlAdminStatus  
  Unsigned32 as traceRouteCtlMaxRows  
  BITS as traceRouteCtlTrapGeneration  
  SnmpAdminString as traceRouteCtlDescr  
  TruthValue as traceRouteCtlCreateHopsEntries  
  OBJECT IDENTIFIER as traceRouteCtlType  
  RowStatus as traceRouteCtlRowStatus  

TraceRouteResultsEntry  
SEQUENCE    
  INTEGER as traceRouteResultsOperStatus  
  Gauge32 as traceRouteResultsCurHopCount  
  Gauge32 as traceRouteResultsCurProbeCount  
  InetAddressType as traceRouteResultsIpTgtAddrType  
  InetAddress as traceRouteResultsIpTgtAddr  
  Unsigned32 as traceRouteResultsTestAttempts  
  Unsigned32 as traceRouteResultsTestSuccesses  
  DateAndTime as traceRouteResultsLastGoodPath  

TraceRouteProbeHistoryEntry  
SEQUENCE    
  Unsigned32 as traceRouteProbeHistoryIndex  
  Unsigned32 as traceRouteProbeHistoryHopIndex  
  Unsigned32 as traceRouteProbeHistoryProbeIndex  
  InetAddressType as traceRouteProbeHistoryHAddrType  
  InetAddress as traceRouteProbeHistoryHAddr  
  Unsigned32 as traceRouteProbeHistoryResponse  
  OperationResponseStatus as traceRouteProbeHistoryStatus  
  Integer32 as traceRouteProbeHistoryLastRC  
  DateAndTime as traceRouteProbeHistoryTime  

TraceRouteHopsEntry  
SEQUENCE    
  Unsigned32 as traceRouteHopsHopIndex  
  InetAddressType as traceRouteHopsIpTgtAddressType  
  InetAddress as traceRouteHopsIpTgtAddress  
  Unsigned32 as traceRouteHopsMinRtt  
  Unsigned32 as traceRouteHopsMaxRtt  
  Unsigned32 as traceRouteHopsAverageRtt  
  Unsigned32 as traceRouteHopsRttSumOfSquares  
  Unsigned32 as traceRouteHopsSentProbes  
  Unsigned32 as traceRouteHopsProbeResponses  
  DateAndTime as traceRouteHopsLastGoodProbe