DL5400-MIB

File: DL5400-MIB.mib (76134 bytes)

Imported modules

RFC-1212 RFC-1215 RFC1155-SMI

Imported symbols

OBJECT-TYPE TRAP-TYPE enterprises
IpAddress TimeTicks Counter

Defined Objects


dl5400 1.3.6.1.4.1.300.110
OBJECT IDENTIFIER    

configuration 1.3.6.1.4.1.300.110.1
OBJECT IDENTIFIER    

dl5400ModulesAppear 1.3.6.1.4.1.300.110.1
There is a module appeared in the device.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

unitLevelConfig 1.3.6.1.4.1.300.110.1.1
OBJECT IDENTIFIER    

unitSerialNum 1.3.6.1.4.1.300.110.1.1.1
An ID that uniquely and globally identifies the unit. A Serial Number must consist of printable ASCII characters 0x20..0x7E.
OBJECT-TYPE    
  DisplayString SIZE(0..20)  

unitName 1.3.6.1.4.1.300.110.1.1.2
A descriptive name that identifies the DL5400 unit. Use of this parameter is optional, but recommended to aid management.
OBJECT-TYPE    
  DisplayString SIZE(0..20)  

unitHwRev 1.3.6.1.4.1.300.110.1.1.3
The DL5400 hardware revision.
OBJECT-TYPE    
  DisplayString SIZE(1..4)  

unitSwRev 1.3.6.1.4.1.300.110.1.1.4
The DL5400 software revision.
OBJECT-TYPE    
  DisplayString SIZE(1..7)  

unitMibRev 1.3.6.1.4.1.300.110.1.1.5
The DL5400 MIB revision.
OBJECT-TYPE    
  DisplayString SIZE(0..20)  

unitFrontPnl 1.3.6.1.4.1.300.110.1.1.6
This feature enables (ON) or disables (OFF) the users ability to make changes in the configuration or run tests from the front panel display and buttons.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

unitDateYear 1.3.6.1.4.1.300.110.1.1.7
The DL5400's date: Year.
OBJECT-TYPE    
  TODYear  

unitDateMonth 1.3.6.1.4.1.300.110.1.1.8
The DL5400's date: Month.
OBJECT-TYPE    
  TODMonth  

unitDateDay 1.3.6.1.4.1.300.110.1.1.9
The DL5400's date: Day.
OBJECT-TYPE    
  TODDay  

unitTimeHour 1.3.6.1.4.1.300.110.1.1.10
The DL5400's time: Hour.
OBJECT-TYPE    
  TODHour  

unitTimeMinute 1.3.6.1.4.1.300.110.1.1.11
The DL5400's time: Minute.
OBJECT-TYPE    
  TODMinute  

unitTimeSecond 1.3.6.1.4.1.300.110.1.1.12
The DL5400's time: Second.
OBJECT-TYPE    
  TODSecond  

unitTimezone 1.3.6.1.4.1.300.110.1.1.13
This object is used to indicate the timezone associated with the time of day that exists on DL5400 System. The enumerated values are defined as hours west of Greenwhich, for example, g01Timezone represents the time zone which is 1 hour west of Greenwhich.
OBJECT-TYPE    
  INTEGER gmtTimezone(1), g01Timezone(2), g02Timezone(3), g03Timezone(4), g04Timezone(5), estTimezone(6), cstTimezone(7), mstTimezone(8), pstTimezone(9), astTimezone(10), hstTimezone(11), g11Timezone(12), g12Timezone(13), g13Timezone(14), g14Timezone(15), g15Timezone(16), g16Timezone(17), g17Timezone(18), g18Timezone(19), g19Timezone(20), g20Timezone(21), g21Timezone(22), g22Timezone(23), g23Timezone(24)  

unitLedStatus 1.3.6.1.4.1.300.110.1.1.14
The defined values have the following description Off - The unit is not equipped or is provision in an out of Service state Green - No alarms, status or test conditions exists for the unit Blink Amber - Test conditions are present in the unit Solid Amber - A minor alarm condition persists in the unit or on some interface of the unit, or the unit is powering up. Red - An Alarm condition persists in the unit or on some interface of the unit Blink-Green - reserved Blink-Red - reserved
OBJECT-TYPE    
  INTEGER off(1), green(2), blink-Green(3), blink-Amber(4), solid-Amber(5), red(6), blink-Red(7)  

unitTimeStamp 1.3.6.1.4.1.300.110.1.1.15
Time Stamp on the unit of format MM/DD/YYYY HH:MM:SS This will be sent as a varbind along with all the traps to NMS manager
OBJECT-TYPE    
  DisplayString SIZE(1..20)  

unitModelType 1.3.6.1.4.1.300.110.1.1.16
The unit model type
OBJECT-TYPE    
  INTEGER ml-pppNxDs1Enet(1)  

unitRouteMode 1.3.6.1.4.1.300.110.1.1.17
Unit Route Mode
OBJECT-TYPE    
  INTEGER staticIp(1), fastForward(2)  

unitTelnetConfig 1.3.6.1.4.1.300.110.1.2
OBJECT IDENTIFIER    

unitTelnetIdleTimeout 1.3.6.1.4.1.300.110.1.2.1
This object is used to indicate number of minutes of inactivity required before setting the telnet access point to auto-logoff.
OBJECT-TYPE    
  INTEGER  

unitDteEnetCfg 1.3.6.1.4.1.300.110.1.3
OBJECT IDENTIFIER    

dteEnetTable 1.3.6.1.4.1.300.110.1.3.1
Table of all Dte Ethernet ports in the system
OBJECT-TYPE    
  SEQUENCE OF  
    DteEnetEntry

dteEnetEntry 1.3.6.1.4.1.300.110.1.3.1.1
An entry in the dteEnetTable
OBJECT-TYPE    
  DteEnetEntry  

dteEnetIndex 1.3.6.1.4.1.300.110.1.3.1.1.1
The dteEnet port index
OBJECT-TYPE    
  INTEGER dte1(1)  

dteEnetIpAddress 1.3.6.1.4.1.300.110.1.3.1.1.2
IP address assigned to the DTE port of the DL5400.
OBJECT-TYPE    
  IpAddress  

dteEnetSubnetMask 1.3.6.1.4.1.300.110.1.3.1.1.3
IP Subnet mask assigned to the DTE port of the DL5400.
OBJECT-TYPE    
  IpAddress  

dteEnetMacAddress 1.3.6.1.4.1.300.110.1.3.1.1.4
Ethernet MAC address of this dte port
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

dteEnetProtocol 1.3.6.1.4.1.300.110.1.3.1.1.5
Ethernet protocol used by the DL5400. dix is also called Ethernet-II.
OBJECT-TYPE    
  INTEGER ethernet(1), ieee8023(2)  

dteEnetOper 1.3.6.1.4.1.300.110.1.3.1.1.6
Ethernet operation used by the DL5400.
OBJECT-TYPE    
  INTEGER autodetect(1), tenMb(2), hundredMb(3)  

dteEnetMode 1.3.6.1.4.1.300.110.1.3.1.1.7
Ethernet mode used by the DL5400.
OBJECT-TYPE    
  INTEGER autodetect(1), halfduplex(2), fullduplex(3)  

dteEnetOperStatus 1.3.6.1.4.1.300.110.1.3.1.1.8
Ethernet operation status
OBJECT-TYPE    
  DisplayString  

dteEnetModeStatus 1.3.6.1.4.1.300.110.1.3.1.1.9
Ethernet Mode status
OBJECT-TYPE    
  DisplayString  

comm1SerialConfig 1.3.6.1.4.1.300.110.1.5
OBJECT IDENTIFIER    

comm1SerialPortState 1.3.6.1.4.1.300.110.1.5.1
This object is used to enable or disable port.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

comm1SerialBaudRate 1.3.6.1.4.1.300.110.1.5.2
COMM 1 Baud Rate.
OBJECT-TYPE    
  DL5400commBaudRate  

comm1SerialBitsPerWord 1.3.6.1.4.1.300.110.1.5.3
COMM 1 Bits Per Word.
OBJECT-TYPE    
  DL5400commNumDataBits  

comm1SerialStopBits 1.3.6.1.4.1.300.110.1.5.4
COMM 1 Stop Bits.
OBJECT-TYPE    
  DL5400commStopBits  

comm1SerialParity 1.3.6.1.4.1.300.110.1.5.5
COMM 1 Parity.
OBJECT-TYPE    
  DL5400commParity  

comm1SerialFlowControl 1.3.6.1.4.1.300.110.1.5.6
COMM 1 Flow Control.
OBJECT-TYPE    
  DL5400commFlowControl  

comm1SerialLogoutOnLos 1.3.6.1.4.1.300.110.1.5.7
This object is used to enable or disable auto-logoff on loss of DSR.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

comm1SerialIdleTimeout 1.3.6.1.4.1.300.110.1.5.8
This object is used to indicate number of minutes of inactivity required before setting this serial access point to auto-logoff.
OBJECT-TYPE    
  INTEGER  

comm2SerialConfig 1.3.6.1.4.1.300.110.1.6
OBJECT IDENTIFIER    

comm2SerialPortState 1.3.6.1.4.1.300.110.1.6.1
This object is used to enable or disable port.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

comm2SerialBaudRate 1.3.6.1.4.1.300.110.1.6.2
COMM 2 Baud Rate.
OBJECT-TYPE    
  DL5400commBaudRate  

comm2SerialBitsPerWord 1.3.6.1.4.1.300.110.1.6.3
COMM 2 Bits Per Word.
OBJECT-TYPE    
  DL5400commNumDataBits  

comm2SerialStopBits 1.3.6.1.4.1.300.110.1.6.4
COMM 2 Stop Bits.
OBJECT-TYPE    
  DL5400commStopBits  

comm2SerialParity 1.3.6.1.4.1.300.110.1.6.5
COMM 2 Parity.
OBJECT-TYPE    
  DL5400commParity  

comm2SerialFlowControl 1.3.6.1.4.1.300.110.1.6.6
COMM 2 Flow Control. HwFlowControl option is not applicable for multidrop serial port when in MultiDrop mode
OBJECT-TYPE    
  DL5400commFlowControl  

comm2SerialLogoutOnLos 1.3.6.1.4.1.300.110.1.6.7
This object is used to enable or disable auto-logoff on loss of DSR.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

comm2SerialIdleTimeout 1.3.6.1.4.1.300.110.1.6.8
This object is used to indicate number of minutes of inactivity required before setting this serial access point to auto-logoff.
OBJECT-TYPE    
  INTEGER  

comm2InMDmode 1.3.6.1.4.1.300.110.1.6.9
This object indicates if this serial port is in multidrop mode or not.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

comm2InMDId 1.3.6.1.4.1.300.110.1.6.10
Identifies the multidrop session
OBJECT-TYPE    
  DisplayString  

netConfig 1.3.6.1.4.1.300.110.1.7
OBJECT IDENTIFIER    

netPriTxClk 1.3.6.1.4.1.300.110.1.7.1
The primary transmit clock source for DL5400.
OBJECT-TYPE    
  DL5400TxClkSrc  

netPriLoopPort 1.3.6.1.4.1.300.110.1.7.2
The primary loop port clock source for DL5400.
OBJECT-TYPE    
  INTEGER  

netSecTxClk 1.3.6.1.4.1.300.110.1.7.3
The secondary transmit clock source for DL5400.
OBJECT-TYPE    
  DL5400TxClkSrc  

netSecLoopPort 1.3.6.1.4.1.300.110.1.7.4
The secondary loop port clock source for DL5400.
OBJECT-TYPE    
  INTEGER  

netExtClkFrequency 1.3.6.1.4.1.300.110.1.7.5
The defined parameters are the external clock frequencies. The user must provision what frequency is to be used
OBJECT-TYPE    
  INTEGER freq8kHZ(1), freq1544kHZ(2)  

netPriStatus 1.3.6.1.4.1.300.110.1.7.6
Primary clock operation status
OBJECT-TYPE    
  DisplayString  

netSecStatus 1.3.6.1.4.1.300.110.1.7.7
Secondary clock operation status
OBJECT-TYPE    
  DisplayString  

netActiveStatus 1.3.6.1.4.1.300.110.1.7.8
Active clock operation status
OBJECT-TYPE    
  DisplayString  

netSuppressYeldet 1.3.6.1.4.1.300.110.1.7.9
This enables or disables the suppression of Yellow Alarm (RAI) detection. Applicable in SF Framing
OBJECT-TYPE    
  INTEGER suppressYelDet(1), allowYelDet(2)  

netLineType 1.3.6.1.4.1.300.110.1.7.10
Tells if this is a T1 or E1 device
OBJECT-TYPE    
  INTEGER t1(1), e1(2)  

netPortTable 1.3.6.1.4.1.300.110.1.7.11
Table of all network port in the system.
OBJECT-TYPE    
  SEQUENCE OF  
    NetPortEntry

netPortEntry 1.3.6.1.4.1.300.110.1.7.11.1
An entry in the Net Port Table
OBJECT-TYPE    
  NetPortEntry  

netPortIndex 1.3.6.1.4.1.300.110.1.7.11.1.1
The network port index.
OBJECT-TYPE    
  INTEGER 1..8  

netAdmin 1.3.6.1.4.1.300.110.1.7.11.1.2
Tells the Net DS1 Admin state
OBJECT-TYPE    
  INTEGER is(1), oos(2), oos-mt(3)  

netFramingFormat 1.3.6.1.4.1.300.110.1.7.11.1.3
This variable describes the Framing Format option for the network port.
OBJECT-TYPE    
  INTEGER esf(2), d4(3)  

netLineCode 1.3.6.1.4.1.300.110.1.7.11.1.4
This variable describes the Line Code option for the network port.
OBJECT-TYPE    
  INTEGER b8zs(2), ami(5)  

netLBO 1.3.6.1.4.1.300.110.1.7.11.1.5
This selects the line build out value in dBs and applies to CSU/DSU mode only.
OBJECT-TYPE    
  INTEGER ft0To133(3), ft133To266(4), ft266To399(5), ft399To533(6), ft533To655(7), lbo-0dB(8), lbo-7p5dB(9), lbo-15dB(10), lbo-22p5dB(11)  

netEGL 1.3.6.1.4.1.300.110.1.7.11.1.6
This selects the equalizer gain limit in dBs and applies to CSU mode only.
OBJECT-TYPE    
  INTEGER egl-36dB(1), egl-30dB(2)  

netFDL 1.3.6.1.4.1.300.110.1.7.11.1.7
'other' indicates that a protocol other than one following is used. 'dsx1Ansi-T1-403' refers to the FDL exchange recommended by ANSI. 'dsx1Att-54016' refers to ESF FDL exchanges. 'dsx1Fdl-none' indicates that the device does not use the FDL.
OBJECT-TYPE    
  INTEGER none(1), ansi(2), att(3), both(4)  

netSetCode 1.3.6.1.4.1.300.110.1.7.11.1.8
enabled or disabled setCode feature.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

netClock 1.3.6.1.4.1.300.110.1.7.11.1.9
This selects the source of Transmit clock.
OBJECT-TYPE    
  INTEGER loopTiming(1), sysTiming(3)  

netFrameStatus 1.3.6.1.4.1.300.110.1.7.11.1.10
Framing Operational State.
OBJECT-TYPE    
  DisplayString  

netFrameUpTime 1.3.6.1.4.1.300.110.1.7.11.1.11
Tells the Framing UpTime.
OBJECT-TYPE    
  TimeTicks  

unitSnmpConfig 1.3.6.1.4.1.300.110.1.8
OBJECT IDENTIFIER    

unitSnmpTrapAddrTable 1.3.6.1.4.1.300.110.1.8.1
A list of IP addresses of the management stations along with information on how to direct a trap to that addresss
OBJECT-TYPE    
  SEQUENCE OF  
    UnitSnmpTrapAddrEntry

unitSnmpTrapAddrEntry 1.3.6.1.4.1.300.110.1.8.1.1
An entry in the Snmp trap address table
OBJECT-TYPE    
  UnitSnmpTrapAddrEntry  

unitSnmpTrapHostAddr 1.3.6.1.4.1.300.110.1.8.1.1.1
Specifies the IP address of the management station to which this unit sends traps.
OBJECT-TYPE    
  IpAddress  

unitSnmpTrapDirection 1.3.6.1.4.1.300.110.1.8.1.1.2
Specifies the way the trap is to be sent to the host
OBJECT-TYPE    
  INTEGER disabled(1), inBand(2), outBand(3)  

unitSnmpTrapDevState 1.3.6.1.4.1.300.110.1.8.2
Specifies whether to forward or block SNMP traps on device.
OBJECT-TYPE    
  INTEGER forward(1), block(2)  

unitSnmpTrapCommunity 1.3.6.1.4.1.300.110.1.8.3
Specifies the Community Name of the management station to which this unit sends traps.
OBJECT-TYPE    
  DisplayString  

unitPPPConfig 1.3.6.1.4.1.300.110.1.9
OBJECT IDENTIFIER    

pppPortTable 1.3.6.1.4.1.300.110.1.9.1
Table of all network ports in the system.
OBJECT-TYPE    
  SEQUENCE OF  
    PPPPortEntry

pppPortEntry 1.3.6.1.4.1.300.110.1.9.1.1
An entry in the PPP Port table
OBJECT-TYPE    
  PPPPortEntry  

pppPortIndex 1.3.6.1.4.1.300.110.1.9.1.1.1
Port number of the Net port.
OBJECT-TYPE    
  INTEGER net1(1), net2(2), net3(3), net4(4), net5(5), net6(6), net7(7), net8(8)  

pppPortInitialMRU 1.3.6.1.4.1.300.110.1.9.1.1.2
The initial Maximum Receive Unit (MRU) that the local PPP entity will advertise to the remote entity. If the value of this variable is 0 then the local PPP entity will not advertise any MRU to the remote entity and the default MRU will be assumed. Changing this object will have effect when the link is next restarted.
OBJECT-TYPE    
  INTEGER  

pppPortMagicNumber 1.3.6.1.4.1.300.110.1.9.1.1.3
If true(2) then the local node will attempt to perform Magic Number negotiation with the remote node. If false(1) then this negotiation is not performed. In any event, the local node will comply with any magic number negotiations attempted by the remote node, per the PPP specification. Changing this object will have effect when the link is next restarted.
OBJECT-TYPE    
  INTEGER false(1), true(2)  

pppPortFcsSize 1.3.6.1.4.1.300.110.1.9.1.1.4
The size of the FCS, in bits, the local node will attempt to negotiate for use with the remote node. Regardless of the value of this object, the local node will comply with any FCS size negotiations initiated by the remote node, per the PPP specification. Changing this object will have effect when the link is next restarted.
OBJECT-TYPE    
  INTEGER size16bits(1), size32bits(2)  

pppPortRestore 1.3.6.1.4.1.300.110.1.9.1.1.5
PPP port restore mode, auto or manual.
OBJECT-TYPE    
  INTEGER auto(1), manual(2)  

unitMLPPPConfig 1.3.6.1.4.1.300.110.1.9.2
OBJECT IDENTIFIER    

mlPPPIpAddress 1.3.6.1.4.1.300.110.1.9.2.1
IP Address assigned to the ML-PPP port of DL5400.
OBJECT-TYPE    
  IpAddress  

mlPPPSubnetMask 1.3.6.1.4.1.300.110.1.9.2.2
IP Subnet mask assigned to the ML-PPP link of DL5400.
OBJECT-TYPE    
  IpAddress  

mlPPPNumberedInterface 1.3.6.1.4.1.300.110.1.9.2.3
Numbered Interface enabled or disabled.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

mlPPPMRRU 1.3.6.1.4.1.300.110.1.9.2.4
Maximum Received Reconstructed Unit of ML-PPP.
OBJECT-TYPE    
  INTEGER  

mlPPPBundleStatus 1.3.6.1.4.1.300.110.1.9.2.5
Tells the current bundle status
OBJECT-TYPE    
  DisplayString  

mlPPPBundleUpTime 1.3.6.1.4.1.300.110.1.9.2.6
The time (in hundredths of a second) since the bundle is up.
OBJECT-TYPE    
  TimeTicks  

mlPPPIPCPState 1.3.6.1.4.1.300.110.1.9.2.7
The current state of IPCP.
OBJECT-TYPE    
  DisplayString  

mlPPPPortTable 1.3.6.1.4.1.300.110.1.9.3
Table of all mlppp port in the system.
OBJECT-TYPE    
  SEQUENCE OF  
    MLPPPPortEntry

mlPPPPortEntry 1.3.6.1.4.1.300.110.1.9.3.1
An entry in the mlppp Port Table
OBJECT-TYPE    
  MLPPPPortEntry  

mlPPPPortIndex 1.3.6.1.4.1.300.110.1.9.3.1.1
The network port index.
OBJECT-TYPE    
  INTEGER 1..8  

mlPPPAdmin 1.3.6.1.4.1.300.110.1.9.3.1.2
Tells the MLPPP Admin State.
OBJECT-TYPE    
  INTEGER is(1), oos(2), oos-mt(3)  

mlPPPStatus 1.3.6.1.4.1.300.110.1.9.3.1.3
Tells the MLPPP Operational State.
OBJECT-TYPE    
  DisplayString  

mlPPPUpTime 1.3.6.1.4.1.300.110.1.9.3.1.4
The time (in hundredths of a second) since the MLPPP is up.
OBJECT-TYPE    
  TimeTicks  

mlPPPLCPState 1.3.6.1.4.1.300.110.1.9.3.1.5
Tells the LCP Operational State.
OBJECT-TYPE    
  DisplayString  

unitRouterConfig 1.3.6.1.4.1.300.110.1.10
OBJECT IDENTIFIER    

unitStaticRoutingTable 1.3.6.1.4.1.300.110.1.10.1
Table of all static routing entries in the system.
OBJECT-TYPE    
  SEQUENCE OF  
    StaticRoutingEntry

staticRoutingEntry 1.3.6.1.4.1.300.110.1.10.1.1
An entry in the static routing table.
OBJECT-TYPE    
  StaticRoutingEntry  

routeDestination 1.3.6.1.4.1.300.110.1.10.1.1.1
Destination of the static route.
OBJECT-TYPE    
  IpAddress  

routeNetworkMask 1.3.6.1.4.1.300.110.1.10.1.1.2
Network Mask
OBJECT-TYPE    
  IpAddress  

routeNextHopAddress 1.3.6.1.4.1.300.110.1.10.1.1.3
Address of the next hop router. The next hop router must be on the same local network as DL5400
OBJECT-TYPE    
  IpAddress  

routeMetric 1.3.6.1.4.1.300.110.1.10.1.1.4
Number of hops between DL5400 and the destination.
OBJECT-TYPE    
  INTEGER  

routeDirection 1.3.6.1.4.1.300.110.1.10.1.1.5
Direction of the Route, Network(NUM) or WAN.
OBJECT-TYPE    
  INTEGER wan(1), num(2)  

routeStatus 1.3.6.1.4.1.300.110.1.10.1.1.6
Writing invalid has the effect of deleting this interface.
OBJECT-TYPE    
  DL5400Validation  

unitArpConfig 1.3.6.1.4.1.300.110.1.11
OBJECT IDENTIFIER    

unitClearArpTable 1.3.6.1.4.1.300.110.1.11.1
Clear all arp entries in the system.
OBJECT-TYPE    
  INTEGER true(1)  

unitArpTable 1.3.6.1.4.1.300.110.1.11.2
Table of all arp entries in the system.
OBJECT-TYPE    
  SEQUENCE OF  
    UnitArpEntry

unitArpEntry 1.3.6.1.4.1.300.110.1.11.2.1
An entry in the arp table.
OBJECT-TYPE    
  UnitArpEntry  

arpEntryNum 1.3.6.1.4.1.300.110.1.11.2.1.1
Entry Number in the arp table.
OBJECT-TYPE    
  INTEGER  

arpIPAddress 1.3.6.1.4.1.300.110.1.11.2.1.2
Entry IpAddress in the arp table.
OBJECT-TYPE    
  IpAddress  

arpMACAddress 1.3.6.1.4.1.300.110.1.11.2.1.3
Entry MAC address in the arp table.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

arpPortNum 1.3.6.1.4.1.300.110.1.11.2.1.4
Entry Port Number in the arp table.
OBJECT-TYPE    
  INTEGER  

alarms 1.3.6.1.4.1.300.110.2
OBJECT IDENTIFIER    

dl5400ModulesDisappear 1.3.6.1.4.1.300.110.2
There is a module disappeared in the device.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

unitAlarmConfig 1.3.6.1.4.1.300.110.2.1
OBJECT IDENTIFIER    

unitAlarmStatusTable 1.3.6.1.4.1.300.110.2.1.1
The Unit Level alarms and status table.
OBJECT-TYPE    
  SEQUENCE OF  
    UnitAlarmStatusEntry

unitAlarmStatusEntry 1.3.6.1.4.1.300.110.2.1.1.1
An Entry in the unit Alarms Table.
OBJECT-TYPE    
  UnitAlarmStatusEntry  

unitAlarmIndex 1.3.6.1.4.1.300.110.2.1.1.1.1
An index value that uniquely identifies a Unit Level alarm entry.
OBJECT-TYPE    
  INTEGER  

unitAlarmSeverity 1.3.6.1.4.1.300.110.2.1.1.1.2
This parameter indicates the severity of the alarm, or may indicate that the data is status only.
OBJECT-TYPE    
  INTEGER status(1), minor(2), major(3)  

unitAlarmType 1.3.6.1.4.1.300.110.2.1.1.1.3
This parameter is the code for the alarm or status type. This code is used to index into an array of text strings to present a message to the human operator.
OBJECT-TYPE    
  DL5400Event  

unitAlarmOriginCardNum 1.3.6.1.4.1.300.110.2.1.1.1.4
The card type of the device originating the event.
OBJECT-TYPE    
  DL5400CardId  

unitAlarmOriginPortNum 1.3.6.1.4.1.300.110.2.1.1.1.5
The port number of the device originating the event.
OBJECT-TYPE    
  DL5400PortId  

events 1.3.6.1.4.1.300.110.3
OBJECT IDENTIFIER    

unitEventTable 1.3.6.1.4.1.300.110.3.1
The Unit Level event history table.
OBJECT-TYPE    
  SEQUENCE OF  
    UnitEventEntry

unitEventEntry 1.3.6.1.4.1.300.110.3.1.1
An entry in the Unit Level event history table.
OBJECT-TYPE    
  UnitEventEntry  

unitEventIndex 1.3.6.1.4.1.300.110.3.1.1.1
An index that uniquely identifies a Unit Level event entry.
OBJECT-TYPE    
  INTEGER  

unitEventSeverity 1.3.6.1.4.1.300.110.3.1.1.2
This parameter indicates whether an entry is status-only or the severity of an alarm entry.
OBJECT-TYPE    
  INTEGER status(1), minor(2), major(3), clear(4), information(5)  

unitEventHour 1.3.6.1.4.1.300.110.3.1.1.3
The hour that the event occurred.
OBJECT-TYPE    
  TODHour  

unitEventMinute 1.3.6.1.4.1.300.110.3.1.1.4
The minute that the event occurred.
OBJECT-TYPE    
  TODMinute  

unitEventSecond 1.3.6.1.4.1.300.110.3.1.1.5
The second that the event occurred.
OBJECT-TYPE    
  TODSecond  

unitEventMonth 1.3.6.1.4.1.300.110.3.1.1.6
The month that the event occurred.
OBJECT-TYPE    
  TODMonth  

unitEventDay 1.3.6.1.4.1.300.110.3.1.1.7
The day that the event occurred.
OBJECT-TYPE    
  TODDay  

unitEventYear 1.3.6.1.4.1.300.110.3.1.1.8
The year that the event occurred.
OBJECT-TYPE    
  TODYear  

unitEventOriginCardNum 1.3.6.1.4.1.300.110.3.1.1.9
The card type of the device originating the event.
OBJECT-TYPE    
  DL5400CardId  

unitEventOriginPortNum 1.3.6.1.4.1.300.110.3.1.1.10
The port number of the device originating the event.
OBJECT-TYPE    
  DL5400PortId  

unitEventType 1.3.6.1.4.1.300.110.3.1.1.11
This parameter is the code for the event type. This code is used to index into an array of text strings to present a message to the human operator.
OBJECT-TYPE    
  DL5400Event  

statistics 1.3.6.1.4.1.300.110.4
OBJECT IDENTIFIER    

arpStats 1.3.6.1.4.1.300.110.4.1
OBJECT IDENTIFIER    

arpbadLengthField 1.3.6.1.4.1.300.110.4.1.1
Bad Length Field
OBJECT-TYPE    
  Counter  

arpunsupportedHardware 1.3.6.1.4.1.300.110.4.1.2
unsupported Hardware
OBJECT-TYPE    
  Counter  

arpunsupportedProtocol 1.3.6.1.4.1.300.110.4.1.3
unsupported Protocol
OBJECT-TYPE    
  Counter  

arpinvalidSenderAddr 1.3.6.1.4.1.300.110.4.1.4
total number of packets with invalid sender protocol address
OBJECT-TYPE    
  Counter  

arpinvalidTargetAddr 1.3.6.1.4.1.300.110.4.1.5
total number of packets with invalid target protocol address
OBJECT-TYPE    
  Counter  

arpbadAddress 1.3.6.1.4.1.300.110.4.1.6
bad address
OBJECT-TYPE    
  Counter  

arppktsReceived 1.3.6.1.4.1.300.110.4.1.7
total number of packets recieved
OBJECT-TYPE    
  Counter  

arpshortPktsReceived 1.3.6.1.4.1.300.110.4.1.8
total number of short packets recieved
OBJECT-TYPE    
  Counter  

arppktsFromMeReceived 1.3.6.1.4.1.300.110.4.1.9
total number of packets from me received
OBJECT-TYPE    
  Counter  

arpsrcBcstReceived 1.3.6.1.4.1.300.110.4.1.10
total number of source broadcasts received
OBJECT-TYPE    
  Counter  

arprepliedSent 1.3.6.1.4.1.300.110.4.1.11
total number of replies sent
OBJECT-TYPE    
  Counter  

arpincomingRequests 1.3.6.1.4.1.300.110.4.1.12
total number of incoming requests
OBJECT-TYPE    
  Counter  

arprequestSent 1.3.6.1.4.1.300.110.4.1.13
total number of requests sent
OBJECT-TYPE    
  Counter  

arpnoMACAddr 1.3.6.1.4.1.300.110.4.1.14
No MAC address
OBJECT-TYPE    
  Counter  

hdlcStatsTable 1.3.6.1.4.1.300.110.4.2
The hdlc statistics table.
OBJECT-TYPE    
  SEQUENCE OF  
    HdlcStatsEntry

hdlcStatsEntry 1.3.6.1.4.1.300.110.4.2.1
An entry in the Hdlc statistics table.
OBJECT-TYPE    
  HdlcStatsEntry  

hdlcPortIndex 1.3.6.1.4.1.300.110.4.2.1.1
Port Index
OBJECT-TYPE    
  INTEGER  

hdlcLinkStatusBadFCSc 1.3.6.1.4.1.300.110.4.2.1.2
Bad FCS
OBJECT-TYPE    
  Counter  

hdlcFramesAborted 1.3.6.1.4.1.300.110.4.2.1.3
Frame aborted
OBJECT-TYPE    
  Counter  

hdlcFramesNotAligned 1.3.6.1.4.1.300.110.4.2.1.4
Frame not aligned
OBJECT-TYPE    
  Counter  

hdlcOctetsRcv 1.3.6.1.4.1.300.110.4.2.1.5
Octets Received
OBJECT-TYPE    
  Counter  

hdlcPctsRcv 1.3.6.1.4.1.300.110.4.2.1.6
Packets Received
OBJECT-TYPE    
  Counter  

hdlcOctetsTrsmt 1.3.6.1.4.1.300.110.4.2.1.7
Octets Transmitted
OBJECT-TYPE    
  Counter  

hdlcPctsTrsmt 1.3.6.1.4.1.300.110.4.2.1.8
Packets Transmitted
OBJECT-TYPE    
  Counter  

miscStats 1.3.6.1.4.1.300.110.4.3
OBJECT IDENTIFIER    

miscprotocolPctsDumped 1.3.6.1.4.1.300.110.4.3.1
Rx packets with IF error on data Ethernet interface
OBJECT-TYPE    
  Counter  

miscnonroutablePcts 1.3.6.1.4.1.300.110.4.3.2
Rx packets non routable on data Ehternet interface
OBJECT-TYPE    
  Counter  

clrStats 1.3.6.1.4.1.300.110.4.4
OBJECT IDENTIFIER    

clearAllStats 1.3.6.1.4.1.300.110.4.4.1
clear all statistics
OBJECT-TYPE    
  INTEGER true(1)  

clearCur15Min 1.3.6.1.4.1.300.110.4.4.2
clear current 15 minutes statistics
OBJECT-TYPE    
  INTEGER true(1)  

clearCur24Hr 1.3.6.1.4.1.300.110.4.4.3
clear current 24 hours statistics
OBJECT-TYPE    
  INTEGER true(1)  

clearOld15Min 1.3.6.1.4.1.300.110.4.4.4
clear old 15 minutes statistics
OBJECT-TYPE    
  INTEGER true(1)  

clearOld24Hr 1.3.6.1.4.1.300.110.4.4.5
clear old 24 hours statistics
OBJECT-TYPE    
  INTEGER true(1)  

maintenance 1.3.6.1.4.1.300.110.5
OBJECT IDENTIFIER    

maintModTable 1.3.6.1.4.1.300.110.5.1
Table of all Module Status in the system
OBJECT-TYPE    
  SEQUENCE OF  
    MaintModEntry

maintModEntry 1.3.6.1.4.1.300.110.5.1.1
An entry in the maintModTable
OBJECT-TYPE    
  MaintModEntry  

maintModIndex 1.3.6.1.4.1.300.110.5.1.1.1
The module index
OBJECT-TYPE    
  INTEGER pp(1), ds1(2), enet(3), mpm(4)  

maintModStatus 1.3.6.1.4.1.300.110.5.1.1.2
Module actual status
OBJECT-TYPE    
  DisplayString  

maintOperstatus 1.3.6.1.4.1.300.110.5.1.1.3
Module Operational status
OBJECT-TYPE    
  DisplayString  

dl5400SelfTestFail 1.3.6.1.4.1.300.110.11
Self Test failed on the unit.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400RamTestFail 1.3.6.1.4.1.300.110.12
RAM Test failed on the unit.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400RomChecksumFail 1.3.6.1.4.1.300.110.13
ROM Checksum failed on the unit.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400FlashChecksumFail 1.3.6.1.4.1.300.110.14
Flash Checksum failed on the unit.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400TimeNotSet 1.3.6.1.4.1.300.110.15
The Unit's time is not set.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400UnitRestart 1.3.6.1.4.1.300.110.16
The Unit is resetting.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400LampTestStart 1.3.6.1.4.1.300.110.17
Lamp Test started.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400LampTestEnd 1.3.6.1.4.1.300.110.18
Lamp Test terminated.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400mgmtPOSTFail 1.3.6.1.4.1.300.110.19
Management POST failed.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400mgmtPOSTok 1.3.6.1.4.1.300.110.20
Management Port OK.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400FrontTemperatureHigh 1.3.6.1.4.1.300.110.21
The unit's front temperature is high.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400FrontTemperatureOK 1.3.6.1.4.1.300.110.22
The unit's front temperature is OK.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400BackTemperatureHigh 1.3.6.1.4.1.300.110.23
The unit's back temperature is high.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400BackTemperatureOK 1.3.6.1.4.1.300.110.24
The unit's back temperature is OK.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400ExternalMajorAlarmStart 1.3.6.1.4.1.300.110.25
The external major alarm input is active on the unit.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400ExternalMajorAlarmEnd 1.3.6.1.4.1.300.110.26
The external major alarm input is de-activated on the unit.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400ExternalMinorAlarmStart 1.3.6.1.4.1.300.110.27
The external minor alarm input is active on the unit.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400ExternalMinorAlarmEnd 1.3.6.1.4.1.300.110.28
The external minor alarm input is de-activated on the unit.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400ExternalStatusAlarmStart 1.3.6.1.4.1.300.110.29
The external status alarm input is active on the unit.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400ExternalStatusAlarmEnd 1.3.6.1.4.1.300.110.30
The external status alarm input is de-activated on the unit.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400PrimaryClockFail 1.3.6.1.4.1.300.110.31
Unit's primary clock has failed.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400PrimaryClockOk 1.3.6.1.4.1.300.110.32
Unit's primary clock is OK.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400SecondaryClockFail 1.3.6.1.4.1.300.110.33
Unit's Secondary clock has failed.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400SecondaryClockOk 1.3.6.1.4.1.300.110.34
Unit's Secondary clock is OK.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400ExternalClockFail 1.3.6.1.4.1.300.110.35
Unit's external clock has failed.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400ExternalClockOk 1.3.6.1.4.1.300.110.36
Unit's external clock is OK.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400Fan1FailAlarm 1.3.6.1.4.1.300.110.37
A fan 1 failed on the unit.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400Fan1Ok 1.3.6.1.4.1.300.110.38
A fan is ok on the unit.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400Fan2FailAlarm 1.3.6.1.4.1.300.110.39
A fan 2 failed on the unit.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400Fan2Ok 1.3.6.1.4.1.300.110.40
A fan 2 is ok on the unit.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400PSFanFailed 1.3.6.1.4.1.300.110.41
Power Supply Fan Failed on the unit.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400PSFanOK 1.3.6.1.4.1.300.110.42
Power Supply Fan OK on the unit.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400PktProcessorPostFail 1.3.6.1.4.1.300.110.43
Packet Processor POST Failed.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400PktProcessorPostOk 1.3.6.1.4.1.300.110.44
Packet Processor POST OK.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400PacketProcessorMissing 1.3.6.1.4.1.300.110.45
Packet Processor Missing.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400PacketProcessorOk 1.3.6.1.4.1.300.110.46
Packet Processor OK.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400VoltageExceeds 1.3.6.1.4.1.300.110.47
Voltage has exceeded allowed operating voltage range
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400VoltageOk 1.3.6.1.4.1.300.110.48
Voltage is within allowed limits
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400ModuleProcessorFail 1.3.6.1.4.1.300.110.49
Module Processor Failed
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400ModuleProcessorOk 1.3.6.1.4.1.300.110.50
Module Processor OK.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400ModulesCfgMismatch 1.3.6.1.4.1.300.110.51
There is configuration mismatch between equipped modules.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400ModulesCfgMatch 1.3.6.1.4.1.300.110.52
There is no configuration mismatch between equipped modules.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400UsePriClkAlarm 1.3.6.1.4.1.300.110.53
Using primary clock source on the unit.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400UseSecClkAlarm 1.3.6.1.4.1.300.110.54
Using secondary clock source on the unit. Primary clock source failed on the unit.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400UseIntClkAlarm 1.3.6.1.4.1.300.110.55
Using internal clock source on the unit. Primary and secondary clock sources failed on the unit.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400UseRxClk1Alarm 1.3.6.1.4.1.300.110.56
Receive multiplexer synced to net 1.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400UseRxClk2Alarm 1.3.6.1.4.1.300.110.57
Receive multiplexer synced to net 2.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400UseRxClk3Alarm 1.3.6.1.4.1.300.110.58
Receive multiplexer synced to net 3.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400UseRxClk4Alarm 1.3.6.1.4.1.300.110.59
Receive multiplexer synced to net 4.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400UseRxClk5Alarm 1.3.6.1.4.1.300.110.60
Receive multiplexer synced to net 5.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400UseRxClk6Alarm 1.3.6.1.4.1.300.110.61
Receive multiplexer synced to net 6.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400UseRxClk7Alarm 1.3.6.1.4.1.300.110.62
Receive multiplexer synced to net 7.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400UseRxClk8Alarm 1.3.6.1.4.1.300.110.63
Receive multiplexer synced to net 8.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400MLpppPOSTFail 1.3.6.1.4.1.300.110.64
ML-PPP POST failed.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400MLpppPOSTok 1.3.6.1.4.1.300.110.65
ML-PPP Port OK.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400MLpppModuleMissing 1.3.6.1.4.1.300.110.66
ML-PPP Module is Missing
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400MLpppModuleOK 1.3.6.1.4.1.300.110.67
ML-PPP Module is OK
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  


dl5400MLpppInsufficientLinksOk 1.3.6.1.4.1.300.110.69
Insufficient ML-PPP links alarm remitted.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400ModulesFail 1.3.6.1.4.1.300.110.70
There is a module failed in the device.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400ModulesUp 1.3.6.1.4.1.300.110.71
There is a module up in the device.
TRAP-TYPE    
  unitEventSeverity  
  unitTimeStamp  

dl5400LossOfSignalStart 1.3.6.1.4.1.300.110.100
Loss of Signal occured on the specified Network port.
TRAP-TYPE    
  unitEventOriginPortNum  
  unitEventSeverity  
  unitTimeStamp  

dl5400LossOfSignalEnd 1.3.6.1.4.1.300.110.101
Loss of Signal ended on the specified Network port.
TRAP-TYPE    
  unitEventOriginPortNum  
  unitEventSeverity  
  unitTimeStamp  

dl5400LossOfFrameStart 1.3.6.1.4.1.300.110.102
Loss of Frame ended on the specified Network port.
TRAP-TYPE    
  unitEventOriginPortNum  
  unitEventSeverity  
  unitTimeStamp  

dl5400LossOfFrameEnd 1.3.6.1.4.1.300.110.103
Loss of Frame ended on the specified Network port.
TRAP-TYPE    
  unitEventOriginPortNum  
  unitEventSeverity  
  unitTimeStamp  

dl5400AisStart 1.3.6.1.4.1.300.110.104
AIS Alarm started on the specified Network port.
TRAP-TYPE    
  unitEventOriginPortNum  
  unitEventSeverity  
  unitTimeStamp  

dl5400AisEnd 1.3.6.1.4.1.300.110.105
AIS Alarm started on the specified Network port.
TRAP-TYPE    
  unitEventOriginPortNum  
  unitEventSeverity  
  unitTimeStamp  

dl5400RaiStart 1.3.6.1.4.1.300.110.106
RAI Alarm(Yellow) received on the specified Network port.
TRAP-TYPE    
  unitEventOriginPortNum  
  unitEventSeverity  
  unitTimeStamp  

dl5400RaiEnd 1.3.6.1.4.1.300.110.107
RAI Alarm(Yellow) Ended on the specified Network port.
TRAP-TYPE    
  unitEventOriginPortNum  
  unitEventSeverity  
  unitTimeStamp  

dl5400netLineRemoteLoopbackStart 1.3.6.1.4.1.300.110.158
Network Line/Remote Loopback on specified Network port .
TRAP-TYPE    
  unitEventOriginPortNum  
  unitEventSeverity  
  unitTimeStamp  

dl5400netLineRemoteLoopbackEnd 1.3.6.1.4.1.300.110.159
Network Line/Remote Loopback ended on specified Network port .
TRAP-TYPE    
  unitEventOriginPortNum  
  unitEventSeverity  
  unitTimeStamp  

dl5400pppEchoTimeout 1.3.6.1.4.1.300.110.164
PPP Echo Timeout.
TRAP-TYPE    
  unitEventOriginPortNum  
  unitEventSeverity  
  unitTimeStamp  

dl5400pppEchoTimeoutRemit 1.3.6.1.4.1.300.110.165
PPP Echo Timeout Alarm Remitted.
TRAP-TYPE    
  unitEventOriginPortNum  
  unitEventSeverity  
  unitTimeStamp  

dl5400pppLineLoopbackStart 1.3.6.1.4.1.300.110.166
PPP Line Loopback Start.
TRAP-TYPE    
  unitEventOriginPortNum  
  unitEventSeverity  
  unitTimeStamp  

dl5400pppLineLoopbackEnd 1.3.6.1.4.1.300.110.167
PPP Line Loopback End.
TRAP-TYPE    
  unitEventOriginPortNum  
  unitEventSeverity  
  unitTimeStamp  

dl5400pppLinkFallbackStart 1.3.6.1.4.1.300.110.168
PPP Link FallbackStart.
TRAP-TYPE    
  unitEventOriginPortNum  
  unitEventSeverity  
  unitTimeStamp  

dl5400pppLinkFallbackEnd 1.3.6.1.4.1.300.110.169
PPP Link Fallback End.
TRAP-TYPE    
  unitEventOriginPortNum  
  unitEventSeverity  
  unitTimeStamp  

dl5400dteLocalLoopbackStart 1.3.6.1.4.1.300.110.170
Network DTE Local Loopback on specified Network port .
TRAP-TYPE    
  unitEventOriginPortNum  
  unitEventSeverity  
  unitTimeStamp  

dl5400dteLocalLoopbackEnd 1.3.6.1.4.1.300.110.171
Network DTE Local Loopback ended on specified Network port .
TRAP-TYPE    
  unitEventOriginPortNum  
  unitEventSeverity  
  unitTimeStamp  

dl5400dteRemoteLoopbackStart 1.3.6.1.4.1.300.110.172
Network DTE Remote Loopback on specified Network port .
TRAP-TYPE    
  unitEventOriginPortNum  
  unitEventSeverity  
  unitTimeStamp  

dl5400dteRemoteLoopbackEnd 1.3.6.1.4.1.300.110.173
Network DTE Remote Loopback ended on specified Network port .
TRAP-TYPE    
  unitEventOriginPortNum  
  unitEventSeverity  
  unitTimeStamp  

dl5400MLpppLinkDown 1.3.6.1.4.1.300.110.174
ML-PPP links down caused by ML-PPP Protocol Layer.
TRAP-TYPE    
  unitEventOriginPortNum  
  unitEventSeverity  
  unitTimeStamp  

dl5400MLpppLinkUp 1.3.6.1.4.1.300.110.175
ML-PPP links up caused by ML-PPP Protocol Layer.
TRAP-TYPE    
  unitEventOriginPortNum  
  unitEventSeverity  
  unitTimeStamp  

Defined Objects

DisplayString  
OCTET STRING    

DL5400Validation  
INTEGER valid(1), invalid(2)    

DL5400commBaudRate  
INTEGER bps1200(1), bps2400(2), bps4800(3), bps9600(4), bps19200(5), bps38400(6), bps57600(7), bps115200(8)    

DL5400commParity  
INTEGER even(1), odd(2), none(3)    

DL5400commStopBits  
INTEGER one(1), oneAndHalf(2), two(3)    

DL5400commNumDataBits  
INTEGER seven(7), eight(8)    

DL5400commFlowControl  
INTEGER xoffUntilXon(1), xoffUntilAny(2), hwFlowControl(3), none(4)    

TODYear  
INTEGER 0..9999    

TODMonth  
INTEGER 1..12    

TODDay  
INTEGER 1..31    

TODHour  
INTEGER 0..23    

TODMinute  
INTEGER 0..59    

TODSecond  
INTEGER 0..59    

DL5400CardId  
INTEGER mpm(1), pp(2), enet(3), ds1(4)    

DL5400PortId  
INTEGER dte(1), nmsEthernet(2), comm1(3), comm2(4), net1(5), net2(6), net3(7), net4(8), net5(9), net6(10), net7(11), net8(12)    

DL5400TxClkSrc  
INTEGER internalClock(1), externalClock(2), rcvrdTiming(3), autoTiming(4)    

DL5400Event  
INTEGER ev-mod-appear(1), ev-mod-disappear(2), ev-system-reset(3), ev-system-initialized(4), ev-timeofday-changed(5), ev-admin-isnr(6), ev-admin-oos(7), ev-admin-oosmt(8), ev-cuisession-inactivitytimeout(9), ev-clkref-configchanged(10), ev-selftest-fail(11), ev-ram-test-fail(12), ev-rom-checksum-fail(13), ev-flash-checksum-fail(14), ev-time-not-set(15), ev-unit-restart(16), ev-lamptest-start(17), ev-lamptest-end(18), ev-mgmt-post-fail(19), ev-mgmt-post-fail-remit(20), ev-front-high-temperature(21), ev-front-high-temperature-remit(22), ev-back-high-temperature(23), ev-back-high-temperature-remit(24), ev-external-major-alarm-input(25), ev-external-major-alarm-input-end(26), ev-external-minor-alarm-input(27), ev-external-minor-alarm-input-end(28), ev-external-status-alarm-input(29), ev-external-status-alarm-input-end(30), ev-primary-clk-fail(31), ev-primary-clk-ok(32), ev-secondary-clk-fail(33), ev-secondary-clk-ok(34), ev-ext-clk-fail(35), ev-ext-clk-ok(36), ev-fan1-fail(37), ev-fan1-ok(38), ev-fan2-fail(39), ev-fan2-ok(40), ev-ps-fan-fail(41), ev-ps-fan-ok(42), ev-packet-processor-post-fail(43), ev-packet-processor-post-ok(44), ev-packet-processor-missing(45), ev-packet-processor-ok(46), ev-voltage-exceeds(47), ev-voltage-ok(48), ev-module-processor-fail(49), ev-module-processor-ok(50), ev-mod-cfg-mismatch(51), ev-mod-cfg-match(52), ev-use-primary-clk(53), ev-use-secondary-clk(54), ev-use-internal-clk(55), ev-use-rx-clk1(56), ev-use-rx-clk2(57), ev-use-rx-clk3(58), ev-use-rx-clk4(59), ev-use-rx-clk5(60), ev-use-rx-clk6(61), ev-use-rx-clk7(62), ev-use-rx-clk8(63), ev-mlppp-post-fail(64), ev-mlppp-post-fail-remit(65), ev-mlppp-module-missing(66), ev-mlppp-module-ok(67), ev-mlppp-insufficient-links(68), ev-mlppp-insufficient-links-remit(69), ev-mod-fail(70), ev-mod-up(71), ev-mod-no-resp(72), ev-mod-hello(73), ev-mod-init-fail(74), ev-mod-init-ok(75), ev-mod-some-ports-failed(76), ev-mod-some-ports-ok(77), ev-mod-all-ports-failed(78), ev-mod-all-ports-ok(79), ev-lost-signal(100), ev-lost-signal-remit(101), ev-lof(102), ev-lof-remit(103), ev-ais(104), ev-ais-remit(105), ev-rai(106), ev-rai-remit(107), ev-red-alarm(108), ev-red-alarm-remit(109), ev-exceeded-cv-consec-sec(110), ev-exceeded-cv-consec-sec-remit(111), ev-exceeded-ses-consec-sec(112), ev-exceeded-ses-consec-sec-remit(113), ev-exceeded-uas-consec-sec(114), ev-exceeded-uas-consec-sec-remit(115), ev-exceeded-pcv-15min-minor-threshold(116), ev-exceeded-pcv-15min-minor-threshold-remit(117), ev-exceeded-pcv-15min-major-threshold(118), ev-exceeded-pcv-15min-major-threshold-remit(119), ev-exceeded-es-15min-minor-threshold(120), ev-exceeded-es-15min-minor-threshold-remit(121), ev-exceeded-es-15min-major-threshold(122), ev-exceeded-es-15min-major-threshold-remit(123), ev-exceeded-ses-15min-minor-threshold(124), ev-exceeded-ses-15min-minor-threshold-remit(125), ev-exceeded-ses-15min-major-threshold(126), ev-exceeded-ses-15min-major-threshold-remit(127), ev-exceeded-sas-15min-minor-threshold(128), ev-exceeded-sas-15min-minor-threshold-remit(129), ev-exceeded-sas-15min-major-threshold(130), ev-exceeded-sas-15min-major-threshold-remit(131), ev-exceeded-uas-15min-minor-threshold(132), ev-exceeded-uas-15min-minor-threshold-remit(133), ev-exceeded-uas-15min-major-threshold(134), ev-exceeded-uas-15min-major-threshold-remit(135), ev-exceeded-pcv-24hr-minor-threshold(136), ev-exceeded-pcv-24hr-minor-threshold-remit(137), ev-exceeded-pcv-24hr-major-threshold(138), ev-exceeded-pcv-24hr-major-threshold-remit(139), ev-exceeded-es-24hr-minor-threshold(140), ev-exceeded-es-24hr-minor-threshold-remit(141), ev-exceeded-es-24hr-major-threshold(142), ev-exceeded-es-24hr-major-threshold-remit(143), ev-exceeded-ses-24hr-minor-threshold(144), ev-exceeded-ses-24hr-minor-threshold-remit(145), ev-exceeded-ses-24hr-major-threshold(146), ev-exceeded-ses-24hr-major-threshold-remit(147), ev-exceeded-sas-24hr-minor-threshold(148), ev-exceeded-sas-24hr-minor-threshold-remit(149), ev-exceeded-sas-24hr-major-threshold(150), ev-exceeded-sas-24hr-major-threshold-remit(151), ev-exceeded-uas-24hr-minor-threshold(152), ev-exceeded-uas-24hr-minor-threshold-remit(153), ev-exceeded-uas-24hr-major-threshold(154), ev-exceeded-uas-24hr-major-threshold-remit(155), ev-net-local-loopback-start(156), ev-net-local-loopback-end(157), ev-net-remote-loopback-start(158), ev-net-remote-loopback-end(159), ev-net-payload-loopback-start(160), ev-net-payload-loopback-end(161), ev-net-BERT-start(162), ev-net-BERT-end(163), ev-ppp-echo-timeout(164), ev-ppp-echo-timeout-remit(165), ev-ppp-loopback-line(166), ev-ppp-loopback-line-remit(167), ev-ppp-link-fallback(168), ev-ppp-link-fallback-remit(169), ev-dte-local-loopback-start(170), ev-dte-local-loopback-end(171), ev-dte-remote-loopback-start(172), ev-dte-remote-loopback-end(173), ev-mlppp-link-down(174), ev-mlppp-link-up(175)    

DteEnetEntry  
SEQUENCE    
  INTEGER as dteEnetIndex  
  IpAddress as dteEnetIpAddress  
  IpAddress as dteEnetSubnetMask  
  OCTET STRING as dteEnetMacAddress  
  INTEGER as dteEnetProtocol  
  INTEGER as dteEnetOper  
  INTEGER as dteEnetMode  
  DisplayString as dteEnetOperStatus  
  DisplayString as dteEnetModeStatus  

NetPortEntry  
SEQUENCE    
  INTEGER as netPortIndex  
  INTEGER as netAdmin  
  INTEGER as netFramingFormat  
  INTEGER as netLineCode  
  INTEGER as netLBO  
  INTEGER as netEGL  
  INTEGER as netFDL  
  INTEGER as netSetCode  
  INTEGER as netClock  
  DisplayString as netFrameStatus  
  TimeTicks as netFrameUpTime  

UnitSnmpTrapAddrEntry  
SEQUENCE    
  IpAddress as unitSnmpTrapHostAddr  
  INTEGER as unitSnmpTrapDirection  

PPPPortEntry  
SEQUENCE    
  INTEGER as pppPortIndex  
  INTEGER as pppPortInitialMRU  
  INTEGER as pppPortMagicNumber  
  INTEGER as pppPortFcsSize  
  INTEGER as pppPortRestore  

MLPPPPortEntry  
SEQUENCE    
  INTEGER as mlPPPPortIndex  
  INTEGER as mlPPPAdmin  
  DisplayString as mlPPPStatus  
  TimeTicks as mlPPPUpTime  
  DisplayString as mlPPPLCPState  

StaticRoutingEntry  
SEQUENCE    
  IpAddress as routeDestination  
  IpAddress as routeNetworkMask  
  IpAddress as routeNextHopAddress  
  INTEGER as routeMetric  
  INTEGER as routeDirection  
  DL5400Validation as routeStatus  

UnitArpEntry  
SEQUENCE    
  INTEGER as arpEntryNum  
  IpAddress as arpIPAddress  
  OCTET STRING as arpMACAddress  
  INTEGER as arpPortNum  

UnitAlarmStatusEntry  
SEQUENCE    
  INTEGER as unitAlarmIndex  
  INTEGER as unitAlarmSeverity  
  DL5400Event as unitAlarmType  
  DL5400CardId as unitAlarmOriginCardNum  
  DL5400PortId as unitAlarmOriginPortNum  

UnitEventEntry  
SEQUENCE    
  INTEGER as unitEventIndex  
  INTEGER as unitEventSeverity  
  TODHour as unitEventHour  
  TODMinute as unitEventMinute  
  TODSecond as unitEventSecond  
  TODMonth as unitEventMonth  
  TODDay as unitEventDay  
  TODYear as unitEventYear  
  DL5400CardId as unitEventOriginCardNum  
  DL5400PortId as unitEventOriginPortNum  
  DL5400Event as unitEventType  

HdlcStatsEntry  
SEQUENCE    
  INTEGER as hdlcPortIndex  
  Counter as hdlcLinkStatusBadFCSc  
  Counter as hdlcFramesAborted  
  Counter as hdlcFramesNotAligned  
  Counter as hdlcOctetsRcv  
  Counter as hdlcPctsRcv  
  Counter as hdlcOctetsTrsmt  
  Counter as hdlcPctsTrsmt  

MaintModEntry  
SEQUENCE    
  INTEGER as maintModIndex  
  DisplayString as maintModStatus  
  DisplayString as maintOperstatus