DMA200-MIB

File: DMA200-MIB.mib (11410 bytes)

Imported modules

RFC1155-SMI RFC1213-MIB RFC-1215
RFC-1212

Imported symbols

enterprises DisplayString TRAP-TYPE
OBJECT-TYPE

Defined Objects

gdc 1.3.6.1.4.1.498
OBJECT IDENTIFIER    

sc 1.3.6.1.4.1.498.3
OBJECT IDENTIFIER    

dmaSystem 1.3.6.1.4.1.498.3.7
OBJECT IDENTIFIER    

dmaMaster 1.3.6.1.4.1.498.3.7.1
OBJECT IDENTIFIER    

dmaAccess 1.3.6.1.4.1.498.3.7.1
The dmaAccess trap is sent whenever the following occurs: value Condition ----- --------- local User plugs in a terminal to the front panel global User enters global mode local User enters local mode none User removes front panel terminal
TRAP-TYPE    
  dmaMasterSupvAccess  

dmaMasterFSterminate 1.3.6.1.4.1.498.3.7.1.1
When set, this object will terminate a terminal session from the front panel FS port. The terminal will display a message to the user that access is terminated.
OBJECT-TYPE    
  INTEGER disconnect(1)  

dmaMasterSupvAccess 1.3.6.1.4.1.498.3.7.1.2
The value of the supervisory port terminal access on the DMA-200 master as sent by the trap. Note: when in global access, this can't be read.
OBJECT-TYPE    
  INTEGER none(1), local(2), global(3)  

dmaMasterModemCmd 1.3.6.1.4.1.498.3.7.1.3
This is the modem 'AT' command string which can be sent for modem configuration. When read, it gives the last response from the modem. If the modem response is greater than 256 bytes in length, the first 256 bytes are read.
OBJECT-TYPE    
  DisplayString SIZE(0..256)  

dmaMasterDialPrefix 1.3.6.1.4.1.498.3.7.1.4
This is the modem 'AT' command string which is sent to the modem before the DialPhoneNumber. The default is ATD.
OBJECT-TYPE    
  DisplayString SIZE(0..16)  

dmaMasterDialPhoneNumber 1.3.6.1.4.1.498.3.7.1.5
The phone number of the remote node (DMA-200 slave or PMC-100 slave) to be dialled. If no dial-out phone number is generated, this value should be set to a zero length string.
OBJECT-TYPE    
  DisplayString SIZE(0..16)  

dmaMasterDialing 1.3.6.1.4.1.498.3.7.1.6
The value initiating the dial or disconnect activity of the DMA-200 master dial-out port. No dialing is initiated if the phone number value is a zero string.
OBJECT-TYPE    
  INTEGER connect(1), disconnect(2)  

dmaMasterDialPortStatus 1.3.6.1.4.1.498.3.7.1.7
The DMA-200 modem port status at the time of the SNMP status request.
OBJECT-TYPE    
  INTEGER readyOffline(1), dialing(2), connectedOnline(3)  

dmaMasterResumeScan 1.3.6.1.4.1.498.3.7.1.8
When written, the DMA200 cancels the internal delay timer and resumes scanning the Network Elements.
OBJECT-TYPE    
  INTEGER  

dmaMasterScanCtrl 1.3.6.1.4.1.498.3.7.1.9
This object is stored in non-volatile memory and controls the scanning process. The first time the unit is powered, the non-volatile memory is set to dmaScanOff. Setting dmaScanOn will begin the scan process. Setting dmaScanOff will stop the scan process and clear any current alarm states.
OBJECT-TYPE    
  INTEGER dmaScanOff(1), dmaScanOn(2)  

dmaNode 1.3.6.1.4.1.498.3.7.2
OBJECT IDENTIFIER    

dmaElementAlarm 1.3.6.1.4.1.498.3.7.2
The dmaElementAlarm trap is sent: a) whenever the dma scans the active network elements and detects a change in status. The element number and the current status are sent. This way the trap is sent when an alarm occurs and when it clears. b) whenever a network element is logged on to by the DMA and a mismatch in dmaElementType is found.
TRAP-TYPE    
  dmaElementIndex  
  dmaElementType  
  dmaElementStatus  
  dmaNodeName  

dmaNodeNum 1.3.6.1.4.1.498.3.7.2.1
Number of DMA-200 and PMC-100 nodes in the system. Firmware revisions E- and below have a maximum of 20 nodes Firmware revisions F- and above have a maximum of 40 nodes
OBJECT-TYPE    
  INTEGER  

dmaNodeTable 1.3.6.1.4.1.498.3.7.2.2
A table that contains information about the nodes in the system.
OBJECT-TYPE    
  SEQUENCE OF  
    DmaNodeEntry

dmaNodeEntry 1.3.6.1.4.1.498.3.7.2.2.1
A list of information for each node in the system.
OBJECT-TYPE    
  DmaNodeEntry  

dmaNodeIndex 1.3.6.1.4.1.498.3.7.2.2.1.1
The value indicates the node number for which this entry contains management information.
OBJECT-TYPE    
  INTEGER 1..20  

dmaNodeValid 1.3.6.1.4.1.498.3.7.2.2.1.2
The value indicates the status of the table row entry for the purpose of creation and deletion of new node instances.
OBJECT-TYPE    
  INTEGER valid(1), invalid(2)  

dmaNodePhoneNumber 1.3.6.1.4.1.498.3.7.2.2.1.3
The phone number of the slave DMA-200 or slave PMC- 100. If no phone number is generated, this value should be set to a zero length string.
OBJECT-TYPE    
  DisplayString SIZE(0..16)  

dmaNodeName 1.3.6.1.4.1.498.3.7.2.2.1.4
A textual description of the node ID such as the name or location of the node site. If no name or location identification is generated, this value should be set to a zero length string.
OBJECT-TYPE    
  DisplayString SIZE(0..8)  

dmaElement 1.3.6.1.4.1.498.3.7.3
OBJECT IDENTIFIER    

dmaElementConfigTable 1.3.6.1.4.1.498.3.7.3.1
A table that contains information about all Network Elements in the system.
OBJECT-TYPE    
  SEQUENCE OF  
    DmaElementEntry

dmaElementEntry 1.3.6.1.4.1.498.3.7.3.1.1
A list of information for each Network Element
OBJECT-TYPE    
  DmaElementEntry  

dmaElementIndex 1.3.6.1.4.1.498.3.7.3.1.1.1
The value indicates the Network Element numeric address for which this entry contains management information.
OBJECT-TYPE    
  INTEGER 0..255  

dmaElementRemoteIndex 1.3.6.1.4.1.498.3.7.3.1.1.2
The value indicates the numeric address of the remote Network Element on the oposite end of the line.
OBJECT-TYPE    
  INTEGER 0..255  

dmaElementValid 1.3.6.1.4.1.498.3.7.3.1.1.3
The value indicates the status of the table row entry for the purpose of creation and deletion of new Network Element instances.
OBJECT-TYPE    
  INTEGER valid(1), invalid(2)  

dmaElementType 1.3.6.1.4.1.498.3.7.3.1.1.4
The value indicates the type the T1-CSU Network Element. This value is set by the manager and sent with traps.
OBJECT-TYPE    
  INTEGER other(1), dc551(2), dc552A(3), dc552A-1(4), dc552A-V11(5), dc552A-1-V11(6)  

dmaElementStatus 1.3.6.1.4.1.498.3.7.3.1.1.5
The value indicates the communication status of the supervisory connection between the DMA-200 Master and the Network Element at the time of the SNMP status request.
OBJECT-TYPE    
  INTEGER statusOK(1), statusMajor(2), statusMinor(3), statusNotResponding(4), statusCommErr(5), statusMismatchDC551(6), statusMismatchDC552A(7), statusMismatchDC552A-1(8), statusMismatchDC552A-V11(9), statusMismatchDC552A-1-V11(10)  

dmaElementNode 1.3.6.1.4.1.498.3.7.3.1.1.6
The value indicates the node number to which this Network Element is attached. Same as the corresponding dmaNodeIndex. A value of zero indicates that this Network Element is attached to no node.
OBJECT-TYPE    
  INTEGER  

Defined Objects

DmaNodeEntry  
SEQUENCE    
  INTEGER as dmaNodeIndex  
  INTEGER as dmaNodeValid  
  DisplayString as dmaNodePhoneNumber  
  DisplayString as dmaNodeName  

DmaElementEntry  
SEQUENCE    
  INTEGER as dmaElementIndex  
  INTEGER as dmaElementRemoteIndex  
  INTEGER as dmaElementValid  
  INTEGER as dmaElementType  
  INTEGER as dmaElementStatus  
  INTEGER as dmaElementNode